Cypress CY7C264-45DC 8k x 8 power-switched and reprogrammable prom Datasheet

CY7C261
CY7C263/CY7C264
8K x 8 Power-Switched and Reprogrammable PROM
Features
Functional Description
• CMOS for optimum speed/power
• Windowed for reprogrammability
• High speed
— 20 ns (commercial)
The CY7C261, CY7C263, and CY7C264 are high-performance 8192-word by 8-bit CMOS PROMs. When deselected,
the 7C261 automatically powers down into a low-power standby mode. It is packaged in a 300-mil-wide package. The 7C263
and 7C264 are packaged in 300-mil-wide and 600-mil-wide
packages respectively, and do not power down when deselected. The reprogrammable packages are equipped with an erasure window; when exposed to UV light, these PROMs are
erased and can then be reprogrammed. The memory cells utilize proven EPROM floating-gate technology and byte-wide intelligent programming algorithms.
— 25 ns (military)
• Low power
— 660 mW (commercial)
— 770 mW (military)
• Super low standby power (7C261)
— Less than 220 mW when deselected
— Fast access: 20 ns
EPROM technology 100% programmable
Slim 300-mil or standard 600-mil packaging available
5V ± 10% VCC, commercial and military
Capable of withstanding greater than 2001V static discharge
• TTL-compatible I/O
• Direct replacement for bipolar PROMs
•
•
•
•
The CY7C261, CY7C263, and CY7C264 are plug-in replacements for bipolar devices and offer the advantages of lower
power, superior performance and programming yield. The
EPROM cell requires only 12.5V for the supervoltage and low
current requirements allow for gang programming. The
EPROM cells allow for each memory location to be tested
100%, as each location is written into, erased, and repeatedly
exercised prior to encapsulation. Each PROM is also tested for
AC performance to guarantee that after customer programming the product will meet DC and AC specification limits.
Read is accomplished by placing an active LOW signal on CS.
The contents of the memory location addressed by the address line (A0−A12) will become available on the output lines
(O0−O7).
Logic Block Diagram
Pin Configurations
O7
A2
A3
ROW
ADDRESS
PROGRAM–
MABLE
ARRAY
COLUMN
MULTI–
PLEXER
DIP/Flatpack
Top View
O6
A7
A6
A5
A4
A3
A2
A1
A0
O0
O1
A4
A5
O5
A6
A7
ADDRESS
DECODER
O4
A8
O3
A9
A10
A11
COLUMN
ADDRESS
O2
A12
O2
GND
VCC
A8
A9
A10
CS
A11
A12
O7
O6
O5
O4
O3
1
24
2
23
3
22
4
21
5
20
6
19
7
18
8 7C261 17
7C263
9 7C264 16
10
15
11
14
12
13
LCC/PLCC (OpaqueOnly)
Top View
A5
A6
A7
NC
VCC
A8
A9
A1
A4
A3
A2
A1
A0
NC
O0
4 3 2 1 28 27 26
25
5
24
6
23
7C261
7
22
8
7C263
21
9
20
10
19
11
12 1314151617 18
A10
CS
A11
A12
NC
O7
O6
O1
O2
GND
NC
O3
O4
O5
A0
O1
POWER DOWN
(7C261)
O0
CS
For an 8K x 8 Registered PROM, see theCY7C265.
Cypress Semiconductor Corporation
Document #: 38-04010 Rev. **
•
3901 North First Street
•
San Jose
•
CA 95134 • 408-943-2600
Revised March 4, 2002
CY7C261
CY7C263/CY7C264
Selection Guide
Maximum Access Time (ns)
Maximum Operating
Current (mA)
Maximum Standby
Current (mA)
(7C261 only)
Commercial
7C261-20
7C263-20
7C264-20
7C261-25
7C263-25
7C264-25
7C261-35
7C263-35
7C264-35
7C261-45
7C263-45
7C264-45
7C261-55
7C263-55
7C264-55
20
25
35
45
55
120
120
100
100
100
140
120
120
120
40
30
30
30
40
30
30
30
Military
Commercial
40
Military
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Storage Temperatures .................................–65°C to+150°C
Latch-Up Current..................................................... >200 mA
Ambient Temperature with
Power Applied..............................................–55°C to+125°C
Operating Range
Supply Voltage to Ground Potential
(Pin 24 to Pin 12) ............................................ –0.5V to+7.0V
DC Voltage Applied to Outputs
in High Z State ................................................ –0.5V to+7.0V
DC Input Voltage........................................... –3.0V to + 7.0V
DC Program Voltage
(Pin 19 DIP, Pin 23 LCC) ..............................................13.0V
Static Discharge Voltage............................................>2001V
(per MIL-STD-883, Method 3015)
Document #: 38-04010 Rev. **
UV Exposure ................................................ 7258 Wsec/cm2
Range
Ambient
Temperature
VCC
Commercial
0°C to + 70°C
5V ± 10%
Industrial[1]
–40°C to + 85°C
5V ± 10%
Military[2]
–55°C to + 125°C
5V ± 10%
Notes:
1. See the Ordering Information section regarding industrial temperature
range specification.
2. TA is the “instant on” case temperature.
Page 2 of 16
CY7C261
CY7C263/CY7C264
]]
Electrical Characteristics Over the Operating Range[3,4]
7C261-20, 25
7C263-20, 25
7C264-20, 25
Parameter
Description
Test Conditions
VOH
Output HIGH Voltage
VCC = Min., IOH = –2.0 mA
VOH
Output HIGH Voltage
VCC = Min., IOH = –4.0 mA
VOL
Output LOW Voltage
VCC = Min., IOL = 8 mA
(6 mA Mil)
VOL
Output LOW Voltage
VCC = Min., IOL = 16 mA
VIH
Input HIGH Level
VIL
Input LOW Level
IIX
Input Current
VCD
Input Diode Clamp Voltage
IOZ
Output Leakage Current
GND <VOUT < VCC
Output Disabled
IOS
Output Short Circuit Current[5]
VCC = Max., VOUT = GND
ICC
Power Supply Current
VCC = Max.,
f = Max.
IOUT= 0 mA
Com’l
Mil
VCC = Max.,
CS > VIH
Com’l
Min.
7C261-35, 45, 55
7C263-35, 45, 55
7C264-35, 45, 55
Max.
Min.
Max.
2.4
V
2.4
V
0.4
V
0.4
2.0
ISB
Standby Supply Current (7C261)
VPP
Programming Supply Voltage
IPP
Programming Supply Current
VIHP
Input HIGH Programming Voltage
VILP
Input LOW Programming Voltage
–10
+10
V
0.8
V
+10
µA
–10
+10
µA
–10
Note 4
Com’l
Mil
V
2.0
0.8
GND < VIN < VCC
Unit
Note 4
–10
+10
–40
+40
–40
+40
µA
–20
–90
–20
–90
mA
120
100
mA
140
120
40
30
Mil
40
12
mA
30
13
12
50
4.75
13
V
50
mA
4.75
0.4
V
0.4
V
Notes:
3. See the last page of this specification for Group A subgroup testing information.
4. See the “Introduction to CMOS PROMs” section of the Cypress Data Book for general information on testing.
5. For test purposes, not more than one output at a time should be shorted. Short circuit test duration should not exceed 30 seconds.]
Capacitance[4]
Parameter
Description
CIN
Input Capacitance
COUT
Output Capacitance
Document #: 38-04010 Rev. **
Test Conditions
TA = 25°C, f = 1 MHz,
VCC = 5.0V
Max.
Unit
10
pF
10
pF
Page 3 of 16
CY7C261
CY7C263/CY7C264
AC Test Loads and Waveforms[4]
Test Load for -20 through -30 speeds
R1 500Ω
(658Ω MIL)
R1 500
(658Ω MIL)
5V
5V
OUTPUT
3.0V
OUTPUT
R2 333Ω
(403Ω MIL)
30 pF
GND
R2 333Ω
(403Ω MIL)
5 pF
90%
10%
90%
10%
≤ 5 ns
≤ 5 ns
INCLUDING
JIG AND
SCOPE
INCLUDING
JIG AND
SCOPE
(a) Normal Load
(b) High Z Load
Equivalent to:
THÉVENIN EQUIVALENT
RTH 200Ω (250Ω MIL)
OUTPUT
2.0V(1.9VMIL)
Test Load for -35 through -55 speeds
R1250 Ω
R1 250Ω
5V
5V
OUTPUT
OUTPUT
R2167 Ω
30pF
INCLUDING
JIG AND
SCOPE
INCLUDING
JIG AND
SCOPE
(c) Normal Load
Equivalent to:
R2167 Ω
5 pF
(d) High Z Load
THÉ VENIN EQUIVALENT
OUTPUT
RTH 100Ω
2.0V
Switching Characteristics Over the Operating Range [2,3,4]
7C261-20
7C263-20
7C264-20
Parameter
Description
Min.
Max.
7C261-25
7C263-25
7C264-25
Min.
Max.
7C261-35
7C263-35
7C264-35
Min.
7C261-45
7C263-45
7C264-45
Max. Min.
Max.
7C261-55
7C263-55
7C264-55
Min.
Max.
Unit
tAA
Address to Output Valid
20
25
35
45
55
ns
tHZCS1
Chip Select Inactive to High Z
(7C263 and 7C264)
12
12
20
30
35
ns
tHZCS2
Chip Select Inactive to High Z
(7C261)
20
25
35
45
55
ns
tACS1
Chip Select Active to Output Valid
(7C263 and 7C264)
12
12
20
30
35
ns
tACS2
Chip Select Active to Output Valid
(7C261)
20
25
35
45
55
ns
tPU
Chip Select Active to Power-Up
(7C261)
tPD
Chip Select Inactive to
Power-Down (7C261)
Document #: 38-04010 Rev. **
0
0
20
0
25
0
35
0
45
ns
55
ns
Page 4 of 16
CY7C261
CY7C263/CY7C264
Switching Waveforms[4]
tPD
VCC
SUPPLY
CURRENT
tPU
50%
50%
A0 - A12
ADDRESS
CS
tAA
tHZCS
tACS
O0 - O7
Erasure Characteristics
Operating Modes
Wavelengths of light less than 4000 angstroms begin to erase
the devices in the windowed package. For this reason, an
opaque label should be placed over the window if the PROM
is exposed to sunlight or fluorescent lighting for extended periods of time.
Read
The recommended dose of ultraviolet light for erasure is a
wavelength of 2537 angstroms for a minimum dose (UV intensity multiplied by exposure time) of 25 Wsec/cm2. For an ultraviolet lamp with a 12 mW/cm2 power rating, the exposure time would
be approximately 35 minutes. The 7C261 or 7C263 needs to
be within 1 inch of the lamp during erasure. Permanent damage may result if the PROM is exposed to high-intensity UV
light for an extended period of time. 7258 Wsec/cm2 is the
recommended maximum dosage.
Read is the normal operating mode for programmed device. In
this mode, all signals are normal TTL levels. The PROM is
addressed with a 13-bit field, a chip select, (active LOW), is
applied to the CS pin, and the contents of the addressed location
appear on the data out pins.
Program, Program Inhibit, Program Verify
These modes are entered by placing a high voltage VPP on pin
19, with pins 18 and 20 set to VILP. In this state, pin 21 becomes a
latch signal, allowing the upper 5 address bits to be latched into an
onboard register, pin 22 becomes an active LOW program (PGM)
signal and pin 23 becomes an active LOW verify (VFY) signal. Pins
22 and 23 should never be active LOW at the same time. The PROGRAM mode exists when PGM is LOW, and VFY is HIGH. The verify
mode exists when the reverse is true, PGM HIGH and VFY LOW and
the program inhibit mode is entered with both PGM and VFY HIGH.
Program inhibit is specifically provided to allow data to be placed on
and removed from the data pins without conflict
Table 1. Mode Selection
Pin Function[6, 7]
Read or Output Disable
A12
A11
A10
A9
A8
CS
O7–O0
Program
NA
VPP
LATCH
PGM
VFY
CS
D7–D0
Read
A12
A11
A10
A9
A8
VIL
O7–O0
Output Disable
A12
A11
A10
A9
A8
VIH
High Z
Program
VILP
VPP
VILP
VILP
VIHP
VILP
D7–D0
Program Inhibit
VILP
VPP
VILP
VIHP
VIHP
VILP
High Z
Program Verify
VILP
VPP
VILP
VIHP
VILP
VILP
O7–O0
Blank Check
VILP
VPP
VILP
VIHP
VILP
VILP
O7–O0
Mode
Notes:
6. X = “don’t care” but not to exceed VCC ±5%.
7. Addresses A8-A12 must be latched through lines A0-A4 in programming modes.
Document #: 38-04010 Rev. **
Page 5 of 16
CY7C261
CY7C263/CY7C264
DIP/Flatpack
Top View
2
23
VFY
A5
3
22
PGM
4
21
5
20
CS
A2/A10
6
19
VPP
A1/A9
7
18
NA
A0/A8
8
7C261 17
D7
D0
9
D6
D1
7C263 16
10 7C264 15
D5
D2
11
14
D4
GND
12
13
D3
A4/A12
A3/A11
A2/A10
A1/A9
A0/A8
NC
D0
4 3 2 1 28 27 26
25
5
24
6
7C261
23
7
22
8
21
9
7C263
20
10
19
11
12 13 14 15 16 17 18
D1
A4 /A
12
A 3/ A
11
LATCH
VFY
PGM
A6
LATCH
CS
VPP
NA
NC
D7
D6
D5
VCC
NC
D3
D4
24
GND
1
D2
A7
A5
A6
A7
NC
VCC
LCC/PLCC (Opaque only)
Top View
Figure 1. Programming Pinouts
Programming Information
Programming support is available from Cypress as well as
from a number of third-party software vendors. For detailed
programming information, including a listing of software pack-
Document #: 38-04010 Rev. **
ages, please see the PROM Programming Information located
at the end of this section. Programming algorithms can be obtained from any Cypress representative.
Page 6 of 16
CY7C261
CY7C263/CY7C264
Typical DC and AC Characteristics
NORMALIZED SUPPLY CURRENT
vs. AMBIENT TEMPERATURE
NORMALIZED SUPPLY CURRENT
vs. SUPPLY VOLTAGE
1.2
1.4
1.2
1.0
TA = 25°C
f = f MAX
0.8
4.5
5.0
5.5
1.1
1.0
0.9
0.8
-55
6.0
SUPPLY VOLTAGE (V)
1.6
1.4
1.2
1.0
0.8
25
125
TA = 25°C
0.4
4.0
30
40
30
20
10
1.0
2.0
3.0
6.0
20
15
10
VCC = 4.5V
TA = 25°C
5
0
5.5
25
4.0
0
0
OUTPUT VOLTAGE (V)
200
400
600
800 1000
CAPACITANCE (pF)
NORMALIZED SUPPLY CURRENT
vs. CYCLE PERIOD
1.05
150
1.00
125
100
75
VCC = 5.0V
TA = 25°C
50
5.0
TYPICAL ACCESS TIME CHANGE
vs. OUTPUT LOADING
50
0
4.5
SUPPLY VOLTAGE (V)
35
175
25
VCC = 5.5V
TA = 25°C
0.95
0.90
0.85
0.80
0.75
1.0
2.0
3.0
OUTPUT VOLTAGE (V)
Document #: 38-04010 Rev. **
0.6
60
OUTPUT SINK CURRENT
vs. OUTPUT VOLTAGE
0
0.0
0.8
OUTPUT SOURCE CURRENT
vs. VOLTAGE
AMBIENT TEMPERATURE (°C)
OUTPUT SINK CURRENT (mA)
125
DELTA t AA (ns)
OUTPUT SOURCE CURRENT (mA)
NORMALIZED ACCESS TIME
NORMALIZED ACCESS TIME
vs. TEMPERATURE
0.6
- 55
25
1.0
AMBIENT TEMPERATURE (°C)
NORMALIZED I CC
0.6
4.0
NORMALIZED ACCESS TIME
1.2
NORMALIZED I CC
NORMALIZED I
CC
1.6
NORMALI ZED ACCESS TIME
vs. SUPPLY VOLTAGE
4.0
0.70
0
25
50
75
100
CYCLE PERIOD (ns)
Page 7 of 16
CY7C261
CY7C263/CY7C264
]
Ordering Information[8]
Speed
(ns)
20
25
35
45
55
Ordering Code
CY7C261-20JC
Package
Name
J64
Package Type
28-Lead Plastic Leaded Chip Carrier
CY7C261-20PC
P13
24-Lead (300-Mil) Molded DIP
CY7C261-20WC
W14
24-Lead (300-Mil) Windowed CerDIP
CY7C261-25JC
J64
28-Lead Plastic Leaded Chip Carrier
CY7C261-25PC
P13
24-Lead (300-Mil) Molded DIP
CY7C261-25WC
W14
24-Lead (300-Mil) Windowed CerDIP
CY7C261-25DMB
D14
24-Lead (300-Mil) CerDIP
CY7C261-25LMB
L64
28-Square Leadless Chip Carrier
CY7C261-25QMB
Q64
28-Pin Windowed Leadless Chip Carrier
CY7C261-25TMB
T73
24-Lead Windowed Cerpack
CY7C261-25WMB
W14
24-Lead (300-Mil) Windowed CerDIP
CY7C261-35JC
J64
28-Lead Plastic Leaded Chip Carrier
CY7C261-35PC
P13
24-Lead (300-Mil) Molded DIP
CY7C261-35WC
W14
24-Lead (300-Mil) Windowed CerDIP
CY7C261-35DMB
D14
24-Lead (300-Mil) CerDIP
CY7C261-35LMB
L64
28-Square Leadless Chip Carrier
CY7C261-35QMB
Q64
28-Pin Windowed Leadless Chip Carrier
CY7C261-35TMB
T73
24-Lead Windowed Cerpack
CY7C261-35WMB
W14
24-Lead (300-Mil) Windowed CerDIP
CY7C261-45JC
J64
28-Lead Plastic Leaded Chip Carrier
CY7C261-45PC
P13
24-Lead (300-Mil) Molded DIP
CY7C261-45WC
W14
24-Lead (300-Mil) Windowed CerDIP
CY7C261-45DMB
D14
24-Lead (300-Mil) CerDIP
CY7C261-45LMB
L64
28-Square Leadless Chip Carrier
CY7C261-45QMB
Q64
28-Pin Windowed Leadless Chip Carrier
CY7C261-45TMB
T73
24-Lead Windowed Cerpack
CY7C261-45WMB
W14
24-Lead (300-Mil) Windowed CerDIP
CY7C261-55JC
J64
28-Lead Plastic Leaded Chip Carrier
CY7C261-55PC
P13
24-Lead (300-Mil) Molded DIP
CY7C261-55WC
W14
24-Lead (300-Mil) Windowed CerDIP
CY7C261-55DMB
D14
24-Lead (300-Mil) CerDIP
CY7C261-55LMB
L64
28-Square Leadless Chip Carrier
CY7C261-55QMB
Q64
28-Pin Windowed Leadless Chip Carrier
CY7C261-55TMB
T73
24-Lead Windowed Cerpack
CY7C261-55WMB
W14
24-Lead (300-Mil) Windowed CerDIP
Operating
Range
Commercial
Commercial
Military
Commercial
Military
Commercial
Military
Commercial
Military
Note:
8. Most of these products are available in industrial temperature range. Contact a Cypress representative for specifications and product availability.
Document #: 38-04010 Rev. **
Page 8 of 16
CY7C261
CY7C263/CY7C264
Ordering Information[8] (continued)
Speed
(ns)
20
25
35
45
55
Ordering Code
Package
Name
Package Type
CY7C263-20JC
J64
28-Lead Plastic Leaded Chip Carrier
CY7C263-20PC
P13
24-Lead (300-Mil) Molded DIP
CY7C263-20WC
W14
24-Lead (300-Mil) Windowed CerDIP
CY7C263-25JC
J64
28-Lead Plastic Leaded Chip Carrier
CY7C263-25PC
P13
24-Lead (300-Mil) Molded DIP
CY7C263-25WC
W14
24-Lead (300-Mil) Windowed CerDIP
CY7C263-25DMB
D14
24-Lead (300-Mil) CerDIP
CY7C263-25LMB
L64
28-Square Leadless Chip Carrier
CY7C263-25QMB
Q64
28-Pin Windowed Leadless Chip Carrier
CY7C263-25TMB
T73
24-Lead Windowed Cerpack
CY7C263-25WMB
W14
24-Lead (300-Mil) Windowed CerDIP
CY7C263-35JC
J64
28-Lead Plastic Leaded Chip Carrier
CY7C263-35PC
P13
24-Lead (300-Mil) Molded DIP
CY7C263-35WC
W14
24-Lead (300-Mil) Windowed CerDIP
CY7C263-35DMB
D14
24-Lead (300-Mil) CerDIP
CY7C263-35LMB
L64
28-Square Leadless Chip Carrier
CY7C263-35QMB
Q64
28-Pin Windowed Leadless Chip Carrier
CY7C263-35TMB
T73
24-Lead Windowed Cerpack
CY7C263-35WMB
W14
24-Lead (300-Mil) Windowed CerDIP
CY7C263-45JC
J64
28-Lead Plastic Leaded Chip Carrier
CY7C263-45PC
P13
24-Lead (300-Mil) Molded DIP
CY7C263-45WC
W14
24-Lead (300-Mil) Windowed CerDIP
CY7C263-45DMB
D14
24-Lead (300-Mil) CerDIP
CY7C263-45LMB
L64
28-Square Leadless Chip Carrier
CY7C263-45QMB
Q64
28-Pin Windowed Leadless Chip Carrier
CY7C263-45TMB
T73
24-Lead Windowed Cerpack
CY7C263-45WMB
W14
24-Lead (300-Mil) Windowed CerDIP
CY7C263-55JC
J64
28-Lead Plastic Leaded Chip Carrier
CY7C263-55PC
P13
24-Lead (300-Mil) Molded DIP
CY7C263-55WC
W14
24-Lead (300-Mil) Windowed CerDIP
CY7C263-55DMB
D14
24-Lead (300-Mil) CerDIP
CY7C263-55LMB
L64
28-Square Leadless Chip Carrier
CY7C263-55QMB
Q64
28-Pin Windowed Leadless Chip Carrier
CY7C263-55TMB
T73
24-Lead Windowed Cerpack
CY7C263-55WMB
W14
24-Lead (300-Mil) Windowed CerDIP
Document #: 38-04010 Rev. **
Operating
Range
Commercial
Commercial
Military
Commercial
Military
Commercial
Military
Commercial
Military
Page 9 of 16
CY7C261
CY7C263/CY7C264
Ordering Information[8] (continued)
Speed
(ns)
20
25
35
45
55
Ordering Code
Package
Name
Operating
Range
Package Type
CY7C264-20DC
D12
24-Lead (600-Mil) CerDIP
CY7C264-20PC
P11
24-Lead (600-Mil) Molded DIP
Commercial
CY7C264-20WC
W12
24-Lead (600-Mil) Windowed CerDIP
CY7C264-25DC
D12
24-Lead (600-Mil) CerDIP
Commercial
CY7C264-25PC
P11
24-Lead (600-Mil) Molded DIP
CY7C264-25WC
W12
24-Lead (600-Mil) Windowed CerDIP
CY7C264-25DMB
D12
24-Lead (600-Mil) CerDIP
CY7C264-25WMB
W12
24-Lead (600-Mil) Windowed CerDIP
Military
CY7C264-35DC
D12
24-Lead (600-Mil) CerDIP
CY7C264-35PC
P11
24-Lead (600-Mil) Molded DIP
Commercial
CY7C264-35WC
W12
24-Lead (600-Mil) Windowed CerDIP
CY7C264-35DMB
D12
24-Lead (600-Mil) CerDIP
CY7C264-35WMB
W12
24-Lead (600-Mil) Windowed CerDIP
CY7C264-45DC
D12
24-Lead (600-Mil) CerDIP
Military
Commercial
CY7C264-45PC
P11
24-Lead (600-Mil) Molded DIP
CY7C264-45WC
W12
24-Lead (600-Mil) Windowed CerDIP
CY7C264-45DMB
D12
24-Lead (600-Mil) CerDIP
CY7C264-45WMB
W12
24-Lead (600-Mil) Windowed CerDIP
Military
CY7C264-55DC
D12
24-Lead (600-Mil) CerDIP
CY7C264-55PC
P11
24-Lead (600-Mil) Molded DIP
Commercial
CY7C264-55WC
W12
24-Lead (600-Mil) Windowed CerDIP
CY7C264-55DMB
D12
24-Lead (600-Mil) CerDIP
CY7C264-55WMB
W12
24-Lead (600-Mil) Windowed CerDIP
Military
MILITARY SPECIFICATION
Group A Subgroup Testing
DC Characteristics
Parameter
Switching Characteristics
Subgroups
Parameter
VOH
1, 2, 3
tAA
VOL
1, 2, 3
tACS1[10]
Subgroups
7, 8, 9, 10, 11
[9]
7, 8, 9, 10, 11
VIH
1, 2, 3
tACS2
VIL
1, 2, 3
IIX
1, 2, 3
Notes:
9. 7C261 only.
10. 7C263 and 7C264 only.
IOZ
1, 2, 3
ICC
1, 2, 3
ISB[9]
1, 2, 3
Document #: 38-04010 Rev. **
7, 8, 9, 10, 11
Page 10 of 16
CY7C261
CY7C263/CY7C264
Package Diagrams
24-Lead (600-Mil) CerDIP D12
MIL-STD-1835 D-3 Config. A
51-80038
24-Lead (300-Mil) CerDIP D14
MIL-STD-1835 D- 9 Config.A
51-80031
Document #: 38-04010 Rev. **
Page 11 of 16
CY7C261
CY7C263/CY7C264
Package Diagrams (continued)
28-Lead Plastic Leaded Chip Carrier J64
51-85001-A
28-Square Leadless Chip Carrier L64
MIL-STD-1835 C-4
51-80051
Document #: 38-04010 Rev. **
Page 12 of 16
CY7C261
CY7C263/CY7C264
Package Diagrams (continued)
24-Lead (600-Mil) Molded DIP P11
51-85016-A
24-Lead (300-Mil) Molded DIP P13/P13A
51-85013-A
Document #: 38-04010 Rev. **
Page 13 of 16
CY7C261
CY7C263/CY7C264
Package Diagrams (continued)
28-Pin Windowed Leadless Chip Carrier Q64
MIL–STD–1835 C–4
51-80102
24-Lead Windowed Cerpack T73
Document #: 38-04010 Rev. **
Page 14 of 16
CY7C261
CY7C263/CY7C264
Package Diagrams (continued)
24-Lead (600-Mil) Windowed CerDIP W12
MIL-STD-1835 D-3 Config. A
24-Lead (300-Mil) Windowed CerDIP W14
MIL-STD-1835 D-9 Config. A
51-80086
Document #: 38-04010 Rev. **
Page 15 of 16
© Cypress Semiconductor Corporation, 2002. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress Semiconductor product. Nor does it convey or imply any license under patent or other rights. Cypress Semiconductor does not authorize
its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
Semiconductor products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress Semiconductor against all charges.
CY7C261
CY7C263/CY7C264
Document Title: CY7C261 CY7C263/CY7C264 8K x 8 Power Switched and Reprogrammable PROM
Document Number: 38-04010
REV.
ECN NO.
Issue
Date
Orig. of
Change
**
113866
3/6/02
DSG
Description of Change
Change from Spec number: 38-00005 to 38-04010
)
Document #: 38-04010 Rev. **
Page 16 of 16
Similar pages