REF : 20090825-B PROD. SPECIFICATION FOR APPROVAL SHIELDED SMD POWER INDUCTOR NAME ABC'S DWG No. PAGE: 1 HP1004□□□□L□-□□□ ABC'S ITEM No. Marking ( White ) Inductance code D B C R56 Ⅰ﹒MECHANICAL DIMENSIONS： E m/m B : 10.5 ± 0.3 m/m C : 3.50 ± 0.3 m/m D : 4.00 max. E : 1.70 ± 0.5 m/m m/m F : 4.50 typ. m/m G : 6.00 typ. m/m H : 13.0 typ. m/m F A A : 11.3 ± 0.4 G H ( PCB Pattern ) a Ⅱ﹒SCHEMATIC DIAGRAM： b 1 2 c Ⅲ﹒MATERIALS LIST： a﹒Core：Iron powder b﹒Wire：Enamelled copper wire Peak Temp：260℃ max. Max time above 230℃ ：50sec max. Max time above 200℃ ：70sec max. c﹒Cilp：Cu / Ni /Sn d﹒Remark：Products comply with RoHS' requirements ( Temp. rise included ) c﹒Resistance to solder heat：260℃. 10 secs. Reflow Area +2.0 ~ 4.0℃ / sec max. Forced Cooling Area -(1.0 ~ 5.0)℃ / sec max. Peak Temperature: 260℃ 230℃ 200 150 70sec max. 100 50 0 AR-001A 150 ~ 200 ℃ / 60 ~ 120sec 50s ec max. Temperature ( ℃ ) b﹒Operating temp .：-55℃ ~ +125℃ Preheat Area +4.0℃ / sec max. 250 Ⅳ﹒GENERAL SPECIFICATION： a﹒Storage temp.：-55℃ ~ +125℃ Temperature Rising Area 50 100 150 Time ( seconds ) 200 250 SPECIFICATION FOR APPROVAL PAGE: 2 REF : 20090825-B PROD. NAME SHIELDED SMD POWER INDUCTOR ABC'S DWG No. HP1004□□□□L□-□□□ ABC'S ITEM No. Ⅴ﹒ELECTRICAL CHARACTERISTICS： RDC ( mΩ ) Inductance L ( μH ) Isat(A) typ. Irms(A) typ. max. typ. HP1004R18ML□-□□□ 0.18 ± 20 ％ 46.0 40.0 0.8 0.7 HP1004R24ML□-□□□ 0.24 ± 20 ％ 44.0 33.0 1.0 0.9 HP1004R36ML□-□□□ 0.36 ± 20 ％ 30.0 32.0 1.2 1.1 HP1004R47ML□-□□□ 0.47 ± 20 ％ 30.0 30.0 1.7 1.5 HP1004R56ML□-□□□ 0.56 ± 20 ％ 22.0 32.0 1.7 1.6 HP1004R78ML□-□□□ 0.78 ± 20 ％ 22.0 27.0 1.9 1.8 HP10041R0ML□-□□□ 1.00 ± 20 ％ 20.0 25.0 2.5 2.3 HP10041R8ML□-□□□ 1.80 ± 20 ％ 16.0 17.0 5.0 4.5 HP10042R0ML□-□□□ 2.00 ± 20 ％ 14.0 16.0 6.0 5.2 HP10044R7ML□-□□□ 4.70 ± 20 ％ 7.6 10.0 14.5 13.0 HP10046R8ML□-□□□ 6.80 ± 20 ％ 7.5 9.0 19.5 17.5 HP1004100ML□-□□□ 10.0 ± 20 ％ 7.0 8.0 30.5 28.0 HP1004150ML□-□□□ 15.0 ± 20 ％ 6.0 6.0 41.5 37.5 HP1004220ML□-□□□ 22.0 ± 20 ％ 4.5 5.0 66.0 60.5 HP1004470ML□-□□□ 47.0 ± 20 ％ 3.0 3.0 190.0 175.0 HP1004101ML□-□□□ 100.0 ± 20 ％ 2.0 2.5 270.0 250.0 DWG No. 1). □：Packaging information … A：Bulk 2). "- □□□ ":Reference code B：Taping Reel 3). Measured frequency of inductance is 100 KHz / 0.25V 4). Isat base on inductance drop 20% typ. of L value at 20℃ 5). Irms base on temp. rise 40℃ typ. AR-001A SPECIFICATION FOR APPROVAL PAGE: 3 REF : 20090825-B PROD. ABC'S DWG No. SHIELDED SMD POWER INDUCTOR NAME HP1004□□□□L□-□□□ ABC'S ITEM No. Ⅵ﹒PACKAGING INFORMATION： ( 1 ) Configuration T Cover Tape A B N 2.0±0.5 ∮C ∮C D G Embossed carrier ※ Carrier tape width : D P:16 m/m 4 m/m End Start R56 R56 R56 Leader no component 200 m/m min. R56 R56 Trailer no component 400 m/m min. Components User direction of feed ( 2 ) Dimensions Unit:m/m Style A B C D 13 - 24 330 21±0.8 13±0.5 24 G 26 +0 N 50 T -0 30.4 ( 3 ) Q'TY & G.W. Per package Inner : Reel Outer : Carton Series HP1004 AR-001A Q'TY (pcs) G.W. (gw) Style Q'TY (pcs) G.W. (Kg) Size (cm) 900 2,500 13 - 24 3,600 11.0 40 x 40 x 24 SPECIFICATION FOR APPROVAL REF : 20090825-B PROD. NAME PAGE: 4 SHIELDED SMD POWER INDUCTOR ABC'S DWG No. HP1004□□□□L□-□□□ ABC'S ITEM No. Ⅶ﹒DWGING NUMBER EXPRESSION： H P 1 0 0 4 Reference code Appendix code 2 : Package Appendix code 1 : Classification Tolerance code Electrical code Dimension code Type code Appendix code 1：Product Classification L：Lead Free Standard products comply with RoHS' requirements 1 ~ 9：Lead Free Special products comply with RoHS' requirements Appendix code 2：Package Information Code AR-001A Inner package Inner package Q'TY A T.B.D. T.B.D B T / R ( Reel package ) 900 pcs Remark SPECIFICATION FOR APPROVAL PAGE: 5 REF : 20090825-B PROD. NAME SHIELDED SMD POWER INDUCTOR ABC'S DWG No. HP1004□□□□L□-□□□ ABC'S ITEM No. Ⅷ﹒RELIABILITY TEST： Test item Solderability Thermal shock test ( Temp. cycle ) Specification Test condition More than 95% of the terminal electrode Shall be covered With fresh solder. Preconditioning: 150℃/16Hrs±30min Dry Bake Solder : Sn96.5 / Ag3 / Cu0.5 or equivalent Solder temp. :245±5℃ Flux : Rosin Dip time: 5±0.5sec Electrical oharacteristics shall not change more than ±20% Room temp. 15 minutes -55 ℃ 30 minutes Room temp. 15 minutes +125 ℃ Total : 50 cycles Humidity Test Temperature : 40±2℃ Humidity : 90±5% Time : 1000 hours High temp. Resistance test Temperature : 125±5℃ Applied current : Per spec. Time : 96 hours AR-001A 30 minutes SPECIFICATION FOR APPROVAL REF : 20090825-B PROD. NAME PAGE: 6 ABC'S DWG No. SHIELDED SMD POWER INDUCTOR HP1004□□□□L□-□□□ ABC'S ITEM No. Ⅸ﹒UL CARD： OBMW2 Magnet Wire-Component September 8, 2000 E174837 JUNG SHING WIRE CO LTD 231 CHUNG CHENG RD, SEC 3 JEN-TEH HSIANG, TAINAN HSIEN TAIWAN Mtl Dsg AIW CFUEWB EIAIW EILOCKY EILOCKW EIW EIW-2 FL.EILOCKY LSFFW LSUEW PEW PEY SF.FLW SF.EIW SF.BY@ SF.FLY@ SF.BLOCKBS SF.EILOCKY# SF.EILOCKBS SF.BW@ SFFW Mark Dsg ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ BC SFFY UEW-1 UEW-2 UEW-4 UEY UEY-2 OC ____ ____ Polyamideimide Polyurethane Polyesterimide Polyesterimide Polyesterimide Polyamideimide Polyamide Modified Epoxy ____ ____ Polyesterimide Polyesterimide Modified Polyester Polyurethane Polyurethane Polyester Polyester Modified Polyester Polyesterimide Modified Polyester Modified Polyester Modified Polyester Polyesterimide Polyesterimide Polyamide ____ ____ ____ ____Nylon ____ Nylon Nylon Modified Polyamide Polyamide Modified Polyamide ____ Modified Polyester Polyurethane ANSI Type Temp Class MW81-C MW75C MW35C ___ ___ 220 130 200 180 200 ___ MW74-C ___ MW79-C ___ ___ MW24-C MW26C MW77C MW27-C MW27-C ___ ___ ___ Mark Dsg ____ ____ ____ ____ ____ ____ 220 200 155 155 130 155 155 155 180 155 155 155 180 180 MW26C MW79 155 155 A not-for-profit organization dedicated to public safety and committed to quality service Page 1 of 2 287806002 Mtl Dsg Coat Typ Coat Typ BC OC Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane Polyamide ____ ____ ____ Nylon Polyamide ANSI Type Temp Class MW80C MW2-C ___ 155 105 130 130 130 130 MW75C MW28-C MW28-C Marking: Compan y name or trademarks Recognized Component Mark. or 榮 星 電 線 @-May be suffixed by LZ; # - May be suffixed by LZ, EL or LZI. LZ - Signifies magned wires twisted together; EL - signifies base coated magn et wire laid parallel with top coat applied overall; LZL - signifies base coated magnet wire twisted together and covered with top coat overall. , material designation or marked designation on packaed o r reel, and See General Information Preceding These Recognitions For use only in equipment where the acceptability of the combination is determined by Underwriters Laboratories Inc. 287806002 AR-001A Page 2 of 2 OBMW2⁄E174837 September 8 , 2000