GL34A THRU GL34J SURFACE MOUNT GLASS PASSIVATED FAST SWITCHING JUNCTION RECTIFIER * Reverse Voltage - 50 to 600 Volts FEATURES ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ For surface mount applications ♦ High temperature metallurgically bonded construction ♦ Glass passivated cavity-free junction ♦ Capable of meeting environmental standards of MIL-S-19500 ♦ Fast switching for high efficiency ♦ High temperature soldering guaranteed: 450°C/5 seconds at terminals. Complete device submersible temperature of 260°C for 10 seconds in solder bath E D DO-213AA T N E P A T Forward Current - 0.5 Ampere SOLDERABLE ENDS 1st BAND 2nd BAND D1= 0.066 0.060 (1.676) (1.524) D2 0.022 (0.559) 0.016 (0.406) D2 = D1 + 0 - 0.008 (0.20) 0.145 (3.683) 0.131(3.327) 1st band denotes type and polarity 2cnd band denotes voltage type MECHANICAL DATA Dimensions in inches and (millimeters) *Glass-plastic encapsulation technique is covered by Patent No. 3,996,602 and brazed-end cap assembly by Patent No. 3,930,306 ® Case: JEDEC DO-213AA molded plastic over glass body Terminals: Plated terminals, solderable per MIL-STD-750, Method 2026 Polarity: Two bands indicate cathode-end - 1st band denotes device type and 2nd band denotes repetitive peak reverse voltage rating Mounting Position: Any Weight: 0.0014 ounce, 0.036 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. Standard recovery device: first band is white SYMBOLS GL34A GL34B GL34D GL34G GL34J Polarity color bands (2nd Band) Maximum repetitive peak reverse voltage VRRM Gray 50 Red 100 Orange 200 Yellow 400 Green 600 Volts Maximum RMS voltage VRMS 35 70 140 280 420 Volts Maximum DC blocking voltage VDC 50 100 200 400 600 Volts Maximum average forward rectified current at TT=75°C I(AV) 0.5 Amp Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) IFSM 10.0 Amps VF 1.2 IR 5.0 50.0 µA 30.0 µA 1.5 µs Maximum instantaneous forward voltage at 0.5A Maximum DC reverse current at rated DC blocking voltage TA=25°C TA=125°C Maximum full load reverse current, full cycle average at TA=55°C IR(AV) 1.3 Volts Typical reverse recovery time (NOTE 1) Typical junction capacitance (NOTE 2) CJ 4.0 pF Maximum thermal resistance (NOTE 3) (NOTE 4) RΘJA RΘJT 150.0 70.0 °C/W TJ, TSTG -65 to +175 °C Operating junction and storage temperature range trr NOTES: (1) Reverse recovery test conditions IF=0.5A, IR=1.0A, Irr=0.25A (2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to ambient, 0.2 x 0.2” (5.0 x 5.0mm) copper pads to each terminal (4) Thermal resistance from junction to terminal, 0.2 x 0.2” (5.0 x 5.0mm) copper pads to each terminal 4/98 RATINGS AND CHARACTERISTIC CURVES GL34A THRU GL34J FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 0.5 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES FIG. 1 - FORWARD CURRENT DERATING CURVE 60 HZ RESISTIVE OR INDUCTIVE LOAD 0.4 0.3 0.2 0.1 10 8.0 6.0 4.0 2.0 0 0 25 50 75 100 125 150 TJ=TJ max. 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 1 10 175 100 NUMBER OF CYCLES AT 60 HZ TERMINAL TEMPERATURE, °C FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG. 4 - TYPICAL REVERSE CHARACTERISTICS 10 INSTANTANEOUS REVERSE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT, AMPERES 10 1 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 0.1 0.1 TJ=25°C 0.01 0 20 40 60 80 PERCENT OF RATED PEAK REVERSE VOLTAGE, % 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 INSTANTANEOUS FORWARD VOLTAGE, VOLTS FIG. 5 - TYPICAL JUNCTION CAPACITANCE 30 JUNCTION CAPACITANCE, pF TJ=100°C 1 TJ=25°C f=1.0 MHZ Vsig=50mVp-p 10 1 1 10 REVERSE VOLTAGE, VOLTS 100 100