ON NCP305LSQ44T1 Voltage detector sery Datasheet

NCP304, NCP305
Voltage Detector Series
The NCP304 and NCP305 series are second generation ultra−low
current voltage detectors. These devices are specifically designed for
use as reset controllers in portable microprocessor based systems
where extended battery life is paramount.
Each series features a highly accurate undervoltage detector with
hysteresis which prevents erratic system reset operation as the
comparator threshold is crossed.
The NCP304 series consists of complementary output devices that
are available with either an active high or active low reset output. The
NCP305 series has an open drain N−Channel output with an active low
reset output.
The NCP304 and NCP305 device series are available in the
SC−82AB package with standard undervoltage thresholds. Additional
thresholds that range from 0.9 V to 4.9 V in 100 mV steps can
be manufactured.
www.onsemi.com
4
1
SC−82AB
SQ SUFFIX
CASE 419C
PIN CONNECTIONS AND
MARKING DIAGRAM
Features
•
•
•
•
•
•
•
Quiescent Current of 1.0 mA Typical
High Accuracy Undervoltage Threshold of 2.0%
Wide Operating Voltage Range of 0.8 V to 10 V
Complementary or Open Drain Reset Output
Active Low or Active High Reset Output
NCV Prefix for Automotive and Other Applications Requiring
Unique Site and Control Change Requirements; AEC−Q100
Qualified and PPAP Capable
These Devices are Pb−Free and are RoHS Compliant
GND
XXX MG
G
Reset
Output
1
2 Vin
(Top View)
XXX
M
G
Typical Applications
•
•
•
•
3 N.C.
4
Microprocessor Reset Controller
Low Battery Detection
Power Fail Indicator
Battery Backup Detection
= Specific Device Code
= Date Code
= Pb−Free Package
(Note: Microdot may be in either location)
ORDERING INFORMATION
See detailed ordering , marking and shipping information in
the ordering information section on page 19 of this data sheet.
NCP305LSQxxT1
Open Drain Output Configuration
NCP304xSQxxT1
Complementary Output Configuration
2
2
Input
1
Input
*
Vref
Reset Output
1
Reset Output
Vref
4
4
GND
GND
This device contains 38 active transistors.
This device contains 37 active transistors.
* The representative block diagram depicts active low reset output ‘L’ suffix devices. The comparator
input is interchanged for the active high output ‘H’ suffix devices.
Figure 1. Representative Block Diagrams
© Semiconductor Components Industries, LLC, 2015
May, 2015 − Rev. 25
1
Publication Order Number:
NCP304/D
NCP304, NCP305
MAXIMUM RATINGS (Note 1)
Rating
Symbol
Value
Unit
Input Power Supply Voltage (Pin 2)
Vin
12
V
Output Voltage (Pin 1)
Complementary, NCP304
N−Channel Open Drain, NCP305
VOUT
Output Current (Pin 1) (Note 2)
IOUT
70
mA
Thermal Resistance, Junction−to−Air
RqJA
285
°C/W
V
−0.3 to Vin+0.3
−0.3 to 12
Maximum Junction Temperature
TJ
+125
°C
Storage Temperature Range
Tstg
−55 to +150
°C
Latchup Performance (Note 3)
Positive
Negative
ILATCHUP
mA
500
170
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. This device series contains ESD protection and exceeds the following tests:
Human Body Model 2000 V per MIL−STD−883, Method 3015.
Machine Model Method 200 V.
2. The maximum package power dissipation limit must not be exceeded.
TJ(max)−TA
PD +
RqJA
3. Maximum Ratings per JEDEC standard JESD78.
ELECTRICAL CHARACTERISTICS (For all values TA = 25°C, unless otherwise noted.)
Characteristic
Symbol
Min
Typ
Max
Unit
Detector Threshold (Pin 2, Vin Decreasing)
VDET−
0.882
0.900
0.918
V
Detector Threshold Hysteresis (Pin 2, Vin Increasing)
VHYS
0.027
0.045
0.063
V
−
−
0.8
−
2.4
3.0
NCP304/5 − 0.9
Supply Current (Pin 2)
(Vin = 0.8 V)
(Vin = 2.9 V)
mA
Iin
Maximum Operating Voltage (Pin 2)
Vin(max)
−
−
10
V
Minimum Operating Voltage (Pin 2)
(TA = −40°C to 85°C)
Vin(min)
−
−
0.55
0.65
0.70
0.80
V
Reset Output Current (Pin 1, Active Low ‘L’ Suffix Devices)
IOUT
mA
N−Channel Sink Current, NCP304, NCP305
(VOUT = 0.05 V, Vin = 0.70 V)
(VOUT = 0.50 V, Vin = 0.85 V)
0.01
0.05
0.05
0.50
−
−
P−Channel Source Current, NCP304
(VOUT = 2.4 V, Vin = 4.5 V)
1.0
2.0
−
Reset Output Current (Pin 1, Active High ‘H’ Suffix Devices)
IOUT
mA
N−Channel Sink Current, NCP304, NCP305
(VOUT = 0.5 V, Vin = 1.5 V)
1.05
2.5
−
P−Channel Source Current, NCP304
(VOUT = 0.4 V, Vin = 0.7 V)
(VOUT = GND, Vin = 0.8 V)
0.011
0.014
0.04
0.08
−
−
ms
Propagation Delay Input to Output (Figure 2)
4. In the case of CMOS Output Type: The time interval between the rising edge of VDD input pulse from 0.7 V to (+VDET) +2.0 V and output
voltage level becoming to VDD/2. In the case of N−Channel Open Drain Output Type: Output pin is pulled up with a resistance of 470 kW
to 5.0 V, the time interval between the rising edge of VDD input pulse from 0.7 V to (+VDET) +2.0 V and output voltage level becoming to
2.5 V.
www.onsemi.com
2
NCP304, NCP305
ELECTRICAL CHARACTERISTICS (continued) (For all values TA = 25°C, unless otherwise noted.)
Characteristic
Symbol
Min
Typ
Max
Unit
Complementary Output NCP304 Series
Output Transition, High to Low (Note 4)
Output Transition, Low to High (Note 4)
tpHL
tpLH
−
−
18
6.0
−
60
N−Channel Open Drain NCP305 Series
Output Transition, High to Low (Note 4)
Output Transition, Low to High (Note 4)
tpHL
tpLH
−
−
18
−
−
100
Detector Threshold (Pin 2, Vin Decreasing)
VDET−
1.764
1.80
1.836
V
Detector Threshold Hysteresis (Pin 2, Vin Increasing)
VHYS
0.054
0.090
0.126
V
−
−
0.8
1.0
2.4
3.0
NCP304/5 − 0.9
NCP304/5 − 1.8
Supply Current (Pin 2)
(Vin = 1.7 V)
(Vin = 3.8 V)
mA
Iin
Maximum Operating Voltage (Pin 2)
Vin(max)
−
−
10
V
Minimum Operating Voltage (Pin 2)
(TA = −40°C to 85°C)
Vin(min)
−
−
0.55
0.65
0.70
0.80
V
Reset Output Current (Pin 1, Active Low ‘L’ Suffix Devices)
IOUT
mA
N−Channel Sink Current, NCP304, NCP305
(VOUT = 0.05 V, Vin = 0.70 V)
(VOUT = 0.50 V, Vin = 1.5 V)
0.01
1.0
0.05
2.0
−
−
P−Channel Source Current, NCP304
(VOUT = 2.4 V, Vin = 4.5 V)
1.0
2.0
−
Reset Output Current (Pin 1, Active High ‘H’ Suffix Devices)
IOUT
N−Channel Sink Current, NCP304, NCP305
(VOUT = 0.5 V, Vin = 5.0 V)
P−Channel Source Current, NCP304
(VOUT = 0.4 V, Vin = 0.7 V)
(VOUT = GND, Vin = 1.5 V)
mA
6.3
11
−
0.011
0.525
0.04
0.6
−
−
ms
Propagation Delay Input to Output (Figure 2)
Complementary Output NCP304 Series
Output Transition, High to Low (Note 4)
Output Transition, Low to High (Note 4)
tpHL
tpLH
−
−
14
15
−
60
N−Channel Open Drain NCP305 Series
Output Transition, High to Low (Note 4)
Output Transition, Low to High (Note 4)
tpHL
tpLH
−
−
14
−
−
100
Detector Threshold (Pin 2, Vin Decreasing)
VDET−
1.960
2.00
2.040
Detector Threshold Hysteresis (Pin 2, Vin Increasing)
VHYS
0.06
0.10
0.14
NCP304/5 − 2.0
Supply Current (Pin 2)
(Vin = 1.9 V)
(Vin = 4.0 V)
V
V
mA
Iin
−
−
0.9
1.1
2.7
3.3
Maximum Operating Voltage (Pin 2)
Vin(max)
−
−
10
V
Minimum Operating Voltage (Pin 2)
(TA = −40°C to 85°C)
Vin(min)
−
−
0.55
0.65
0.70
0.80
V
Reset Output Current (Pin 1, Active Low ‘L’ Suffix Devices)
IOUT
mA
4. In the case of CMOS Output Type: The time interval between the rising edge of VDD input pulse from 0.7 V to (+VDET) +2.0 V and output
voltage level becoming to VDD/2. In the case of N−Channel Open Drain Output Type: Output pin is pulled up with a resistance of 470 kW
to 5.0 V, the time interval between the rising edge of VDD input pulse from 0.7 V to (+VDET) +2.0 V and output voltage level becoming to
2.5 V.
www.onsemi.com
3
NCP304, NCP305
ELECTRICAL CHARACTERISTICS (continued) (For all values TA = 25°C, unless otherwise noted.)
Characteristic
Symbol
Min
Typ
Max
N−Channel Sink Current, NCP304, NCP305
(VOUT = 0.05 V, Vin = 0.70 V)
(VOUT = 0.50 V, Vin = 1.5 V)
0.01
1.0
0.05
2.0
−
−
P−Channel Source Current, NCP304
(VOUT = 2.4 V, Vin = 4.5 V)
1.0
2.0
−
Unit
NCP304/5 − 2.0
Reset Output Current (Pin 1, Active High ‘H’ Suffix Devices)
IOUT
N−Channel Sink Current, NCP304, NCP305
(VOUT = 0.5 V, Vin = 5.0 V)
P−Channel Source Current, NCP304
(VOUT = 0.4 V, Vin = 0.7 V)
(VOUT = GND, Vin = 1.5 V)
mA
6.3
11
−
0.011
0.525
0.04
0.6
−
−
ms
Propagation Delay Input to Output (Figure 2)
Complementary Output NCP304 Series
Output Transition, High to Low (Note 4)
Output Transition, Low to High (Note 4)
tpHL
tpLH
−
−
13
15
−
60
N−Channel Open Drain NCP305 Series
Output Transition, High to Low (Note 4)
Output Transition, Low to High (Note 4)
tpHL
tpLH
−
−
13
−
−
100
Detector Threshold (Pin 2, Vin Decreasing)
VDET−
2.646
2.700
2.754
V
Detector Threshold Hysteresis (Pin 2, Vin Increasing)
VHYS
0.081
0.135
0.189
V
−
−
0.9
1.1
2.7
3.3
NCP304/5 − 2.7
Supply Current (Pin 2)
(Vin = 2.6 V)
(Vin = 4.7 V)
mA
Iin
Maximum Operating Voltage (Pin 2)
Vin(max)
−
−
10
V
Minimum Operating Voltage (Pin 2)
(TA = −40°C to 85°C)
Vin(min)
−
−
0.55
0.65
0.70
0.80
V
Reset Output Current (Pin 1, Active Low ‘L’ Suffix Devices)
IOUT
mA
N−Channel Sink Current, NCP304, NCP305
(VOUT = 0.05 V, Vin = 0.70 V)
(VOUT = 0.50 V, Vin = 1.5 V)
0.01
1.0
0.05
2.0
−
−
P−Channel Source Current, NCP304
(VOUT = 2.4 V, Vin = 4.5 V)
1.0
2.0
−
Reset Output Current (Pin 1, Active High ‘H’ Suffix Devices)
IOUT
N−Channel Sink Current, NCP304, NCP305
(VOUT = 0.5 V, Vin = 5.0 V)
P−Channel Source Current, NCP304
(VOUT = 0.4 V, Vin = 0.7 V)
(VOUT = GND, Vin = 1.5 V)
mA
6.3
11
−
0.011
0.525
0.04
0.6
−
−
ms
Propagation Delay Input to Output (Figure 2)
Complementary Output NCP304 Series
Output Transition, High to Low (Note 4)
Output Transition, Low to High (Note 4)
tpHL
tpLH
−
−
12
19
−
60
N−Channel Open Drain NCP305 Series
Output Transition, High to Low (Note 4)
Output Transition, Low to High (Note 4)
tpHL
tpLH
−
−
12
−
−
100
4. In the case of CMOS Output Type: The time interval between the rising edge of VDD input pulse from 0.7 V to (+VDET) +2.0 V and output
voltage level becoming to VDD/2. In the case of N−Channel Open Drain Output Type: Output pin is pulled up with a resistance of 470 kW
to 5.0 V, the time interval between the rising edge of VDD input pulse from 0.7 V to (+VDET) +2.0 V and output voltage level becoming to
2.5 V.
www.onsemi.com
4
NCP304, NCP305
ELECTRICAL CHARACTERISTICS (continued) (For all values TA = 25°C, unless otherwise noted.)
Characteristic
Symbol
Min
Typ
Max
Unit
Detector Threshold (Pin 2, Vin Decreasing)
VDET−
2.842
2.900
2.958
V
Detector Threshold Hysteresis (Pin 2, Vin Increasing)
VHYS
0.087
0.145
0.203
V
−
−
0.9
1.1
2.9
3.5
NCP304/5 − 2.9
Supply Current (Pin 2)
(Vin = 2.8 V)
(Vin = 4.9 V)
mA
Iin
Maximum Operating Voltage (Pin 2)
Vin(max)
−
−
10
V
Minimum Operating Voltage (Pin 2)
(TA = −40°C to 85°C)
Vin(min)
−
−
0.55
0.65
0.70
0.80
V
Reset Output Current (Pin 1, Active Low ‘L’ Suffix Devices)
IOUT
mA
N−Channel Sink Current, NCP304, NCP305
(VOUT = 0.05 V, Vin = 0.70 V)
(VOUT = 0.50 V, Vin = 1.5 V)
0.01
1.0
0.05
2.0
−
−
P−Channel Source Current, NCP304
(VOUT = 2.4 V, Vin = 4.5 V)
1.0
2.0
−
Reset Output Current (Pin 1, Active High ‘H’ Suffix Devices)
IOUT
N−Channel Sink Current, NCP304, NCP305
(VOUT = 0.5 V, Vin = 5.0 V)
P−Channel Source Current, NCP304
(VOUT = 0.4 V, Vin = 0.7 V)
(VOUT = GND, Vin = 1.5 V)
mA
6.3
11
−
0.011
0.525
0.04
0.6
−
−
ms
Propagation Delay Input to Output (Figure 2)
Complementary Output NCP304 Series
Output Transition, High to Low (Note 4)
Output Transition, Low to High (Note 4)
tpHL
tpLH
−
−
12
19
−
60
N−Channel Open Drain NCP305 Series
Output Transition, High to Low (Note 4)
Output Transition, Low to High (Note 4)
tpHL
tpLH
−
−
12
−
−
100
Detector Threshold (Pin 2, Vin Decreasing)
VDET−
2.94
3.00
3.06
V
Detector Threshold Hysteresis (Pin 2, Vin Increasing)
VHYS
0.09
0.15
0.21
V
−
−
1.0
1.2
3.0
3.6
NCP304/5 − 3.0
Supply Current (Pin 2)
(Vin = 2.87 V)
(Vin = 5.0 V)
mA
Iin
Maximum Operating Voltage (Pin 2)
Vin(max)
−
−
10
V
Minimum Operating Voltage (Pin 2)
(TA = −40°C to 85°C)
Vin(min)
−
−
0.55
0.65
0.70
0.80
V
Reset Output Current (Pin 1, Active Low ‘L’ Suffix Devices)
IOUT
mA
N−Channel Sink Current, NCP304, NCP305
(VOUT = 0.05 V, Vin = 0.70 V)
(VOUT = 0.50 V, Vin = 1.5 V)
0.01
1.0
0.05
2.0
−
−
P−Channel Source Current, NCP304
(VOUT = 2.4 V, Vin = 4.5 V)
1.0
2.0
−
Reset Output Current (Pin 1, Active High ‘H’ Suffix Devices)
IOUT
N−Channel Sink Current, NCP304, NCP305
(VOUT = 0.5 V, Vin = 5.0 V)
mA
6.3
11
−
4. In the case of CMOS Output Type: The time interval between the rising edge of VDD input pulse from 0.7 V to (+VDET) +2.0 V and output
voltage level becoming to VDD/2. In the case of N−Channel Open Drain Output Type: Output pin is pulled up with a resistance of 470 kW
to 5.0 V, the time interval between the rising edge of VDD input pulse from 0.7 V to (+VDET) +2.0 V and output voltage level becoming to
2.5 V.
www.onsemi.com
5
NCP304, NCP305
ELECTRICAL CHARACTERISTICS (continued) (For all values TA = 25°C, unless otherwise noted.)
Characteristic
Symbol
Min
Typ
Max
0.011
0.525
0.04
0.6
−
−
Unit
NCP304/5 − 3.0
P−Channel Source Current, NCP304
(VOUT = 0.4 V, Vin = 0.7 V)
(VOUT = GND, Vin = 1.5 V)
ms
Propagation Delay Input to Output (Figure 2)
Complementary Output NCP304 Series
Output Transition, High to Low (Note 4)
Output Transition, Low to High (Note 4)
tpHL
tpLH
−
−
12
19
−
60
N−Channel Open Drain NCP305 Series
Output Transition, High to Low (Note 4)
Output Transition, Low to High (Note 4)
tpHL
tpLH
−
−
12
−
−
100
Detector Threshold (Pin 2, Vin Decreasing)
VDET−
4.410
4.500
4.590
V
Detector Threshold Hysteresis (Pin 2, Vin Increasing)
VHYS
0.135
0.225
0.315
V
−
−
−
−
3.0
3.9
NCP304/5 − 4.5
Supply Current (Pin 2)
(Vin = 4.34 V)
(Vin = 6.5 V)
mA
Iin
Maximum Operating Voltage (Pin 2)
Vin(max)
−
−
10
V
Minimum Operating Voltage (Pin 2)
(TA = −40°C to 85°C)
Vin(min)
−
−
0.55
0.65
0.70
0.80
V
Reset Output Current (Pin 1, Active Low ‘L’ Suffix Devices)
IOUT
mA
N−Channel Sink Current, NCP304, NCP305
(VOUT = 0.05 V, Vin = 0.70 V)
(VOUT = 0.50 V, Vin = 1.5 V)
0.01
1.0
0.05
2.0
−
−
P−Channel Source Current, NCP304
(VOUT = 5.9 V, Vin = 8.0 V)
1.5
3.0
−
Reset Output Current (Pin 1, Active High ‘H’ Suffix Devices)
IOUT
N−Channel Sink Current, NCP304, NCP305
(VOUT = 0.5 V, Vin = 5.0 V)
P−Channel Source Current, NCP304
(VOUT = 0.4 V, Vin = 0.7 V)
(VOUT = GND, Vin = 1.5 V)
mA
6.3
11
−
0.011
0.525
0.04
0.6
−
−
ms
Propagation Delay Input to Output (Figure 2)
Complementary Output NCP304 Series
Output Transition, High to Low (Note 4)
Output Transition, Low to High (Note 4)
tpHL
tpLH
−
−
10
21
−
60
N−Channel Open Drain NCP305 Series
Output Transition, High to Low (Note 4)
Output Transition, Low to High (Note 4)
tpHL
tpLH
−
−
10
−
−
100
Detector Threshold (Pin 2, Vin Decreasing)
VDET−
4.606
4.70
4.794
V
Detector Threshold Hysteresis (Pin 2, Vin Increasing)
VHYS
0.141
0.235
0.329
V
−
−
1.1
1.3
3.0
3.9
−
−
10
NCP304/5 − 4.7
Supply Current (Pin 2)
(Vin = 4.54 V)
(Vin = 6.7 V)
mA
Iin
Maximum Operating Voltage (Pin 2)
Vin(max)
V
4. In the case of CMOS Output Type: The time interval between the rising edge of VDD input pulse from 0.7 V to (+VDET) +2.0 V and output
voltage level becoming to VDD/2. In the case of N−Channel Open Drain Output Type: Output pin is pulled up with a resistance of 470 kW
to 5.0 V, the time interval between the rising edge of VDD input pulse from 0.7 V to (+VDET) +2.0 V and output voltage level becoming to
2.5 V.
www.onsemi.com
6
NCP304, NCP305
ELECTRICAL CHARACTERISTICS (continued) (For all values TA = 25°C, unless otherwise noted.)
Characteristic
Symbol
Min
Typ
Max
Unit
Vin(min)
−
−
0.55
0.65
0.70
0.80
V
NCP304/5 − 4.7
Minimum Operating Voltage (Pin 2)
(TA = −40°C to 85°C)
Reset Output Current (Pin 1, Active Low ‘L’ Suffix Devices)
IOUT
mA
N−Channel Sink Current, NCP304, NCP305
(VOUT = 0.05 V, Vin = 0.70 V)
(VOUT = 0.50 V, Vin = 1.5 V)
0.01
1.0
0.05
2.0
−
−
P−Channel Source Current, NCP304
(VOUT = 5.9 V, Vin = 8.0 V)
1.5
3.0
−
Reset Output Current (Pin 1, Active High ‘H’ Suffix Devices)
IOUT
N−Channel Sink Current, NCP304, NCP305
(VOUT = 0.5 V, Vin = 5.0 V)
P−Channel Source Current, NCP304
(VOUT = 0.4 V, Vin = 0.7 V)
(VOUT = GND, Vin = 1.5 V)
mA
6.3
11
−
0.011
0.525
0.04
0.6
−
−
ms
Propagation Delay Input to Output (Figure 2)
Complementary Output NCP304 Series
Output Transition, High to Low (Note 4)
Output Transition, Low to High (Note 4)
tpHL
tpLH
−
−
10
21
−
60
N−Channel Open Drain NCP305 Series
Output Transition, High to Low (Note 4)
Output Transition, Low to High (Note 4)
tpHL
tpLH
−
−
10
−
−
100
4. In the case of CMOS Output Type: The time interval between the rising edge of VDD input pulse from 0.7 V to (+VDET) +2.0 V and output
voltage level becoming to VDD/2. In the case of N−Channel Open Drain Output Type: Output pin is pulled up with a resistance of 470 kW
to 5.0 V, the time interval between the rising edge of VDD input pulse from 0.7 V to (+VDET) +2.0 V and output voltage level becoming to
2.5 V.
www.onsemi.com
7
NCP304, NCP305
VDET+ + 2
Input Voltage, Pin 2
0.7
0V
5V
Reset Output Voltage, Pin 1
2.5 V
NCP305L
Open Drain
0.5 V
0V
VDET+ + 2
Reset Output Voltage, Pin 1
VDET+ + 2
2
0V
NCP304L
Complementary
0.1 V
tpLH
tpHL
NCP304 and NCP305 series are measured with a 10 pF capacitive load. NCP305 has an additional 470 k pullup resistor connected
from the reset output to +5.0 V. The reset output voltage waveforms are shown for the active low ‘L’ devices. The upper detector
threshold, VDET+ is the sum of the lower detector threshold, VDET− plus the input hysteresis, VHYS.
Figure 2. Propagation Delay Measurement Conditions
www.onsemi.com
8
NCP304, NCP305
Table 1. NCP304 SERIES ELECTRICAL CHARACTERISTIC TABLE FOR 0.9 − 4.9 V
Detector Threshold
Hysteresis
Vin Low
Vin High
Vin Low
Vin High
P−Channel
Source
Current
VHYS (V)
Iin
(mA)
(Note 5)
Iin
(mA)
(Note 6)
IOUT
(mA)
(Note 7)
IOUT
(mA)
(Note 8)
IOUT
(mA)
(Note 9)
Supply Current
Detector Threshold
VDET− (V)
N−Chl Sink Current
Min
Typ
Max
Min
Typ
Max
Typ
Typ
Typ
Typ
Typ
NCP304LSQ09T1
0.882
0.9
0.918
0.027
0.045
0.063
0.8
0.9
0.05
0.5
2.0
NCP304LSQ15T1
1.470
1.5
1.530
0.045
0.075
0.105
NCP304LSQ18T1
1.764
1.8
1.836
0.054
0.090
0.126
NCP304LSQ20T1
1.960
2.0
2.040
0.060
0.100
0.140
0.9
1.1
NCP304LSQ23T1
2.254
2.3
2.346
0.069
0.115
0.161
NCP304LSQ25T1
2.450
2.5
2.550
0.075
0.125
0.175
NCP304LSQ27T1
2.646
2.7
2.754
0.081
0.135
0.189
NCP304LSQ28T1
2.744
2.8
2.856
0.084
0.140
0.196
NCP304LSQ29T1
2.842
2.9
2.958
0.087
0.145
0.203
NCP304LSQ30T1
2.940
3.0
3.060
0.090
0.150
0.210
1.0
1.2
NCP304LSQ31T1
3.038
3.1
3.162
0.093
0.155
0.217
NCP304LSQ33T1
3.234
3.3
3.366
0.099
0.165
0.231
NCP304LSQ37T1
3.626
3.7
3.774
0.111
0.185
0.259
NCP304LSQ38T1
3.724
3.8
3.876
0.114
0.190
0.266
NCP304LSQ40T1
3.920
4.0
4.080
0.120
0.200
0.280
1.1
1.3
NCP304LSQ42T1
4.116
4.2
4.284
0.126
0.210
0.294
NCP304LSQ43T1
4.214
4.3
4.386
0.129
0.215
0.301
NCP304LSQ45T1
4.410
4.5
4.590
0.135
0.225
0.315
NCP304LSQ46T1
4.508
4.6
4.692
0.138
0.230
0.322
NCP304LSQ47T1
4.606
4.7
4.794
0.141
0.235
0.329
Part Number
5.
6.
7.
8.
Condition 1:
Condition 2:
Condition 3:
Condition 4:
Condition 4:
9. Condition 5:
3.0
0.9 − 2.9 V, Vin = VDET− − 0.10 V; 3.0 − 3.9 V, Vin = VDET− − 0.13 V; 4.0 − 4.9 V, Vin = VDET− − 0.16 V
0.9 − 4.9 V, Vin = VDET− + 2.0 V
0.9 − 4.9 V, Vin = 0.7 V, VOUT = 0.05 V, Active Low ‘L’ Suffix Devices
0.9 − 1.0 V, Vin = 0.85 V, VOUT = 0.5 V; 1.1 − 1.5 V, Vin = 1.0 V, VOUT = 0.5 V; 1.6 − 4.9 V, Vin = 1.5 V, VOUT = 0.5 V,
Active Low ‘L’ Suffix Devices
0.9 − 3.9 V, Vin = 4.5 V, VOUT = 2.4 V; 4.0 − 4.9 V, Vin = 8.0 V, VOUT = 5.9 V, Active Low ‘L’ Suffix Devices
Table 2. NCP304 SERIES ELECTRICAL CHARACTERISTIC TABLE FOR 0.9 − 4.9 V
Detector Threshold
Detector Threshold
Hysteresis
Vin Low
Vin High
N−Channel
Sink
Current
VHYS (V)
Iin
(mA)
(Note 10)
Iin
(mA)
(Note 11)
IOUT
(mA)
(Note 12)
VDET− (V)
Supply Current
P−Channel
Source Current
Vin Low
Vin High
IOUT
(mA)
(Note 13)
IOUT
(mA)
(Note 14)
Min
Typ
Max
Min
Typ
Max
Typ
Typ
Typ
Typ
Typ
NCP304HSQ09T1
0.882
0.9
0.918
0.027
0.045
0.063
0.8
0.9
2.5
0.04
0.08
NCP304HSQ18T1
NCP304HSQ20T1
NCP304HSQ22T1
NCP304HSQ27T1
NCP304HSQ29T1
NCP304HSQ30T1
NCP304HSQ45T1
NCP304HSQ47T1
1.764
1.960
2.156
2.646
2.842
2.940
4.410
4.606
1.8
2.0
2.2
2.7
2.9
3.0
4.5
4.7
1.836
2.040
2.244
2.754
2.958
3.060
4.590
4.794
0.054
0.060
0.066
0.081
0.087
0.090
0.135
0.141
0.090
0.100
0.110
0.135
0.145
0.150
0.225
0.235
0.126
0.140
0.154
0.189
0.203
0.210
0.315
0.329
0.9
1.1
1.0
1.2
Part Number
10. Condition 1: 0.9 − 2.9 V, Vin = VDET− − 0.10 V; 3.0 − 3.9 V, Vin = VDET− − 0.13 V; 4.0 − 4.9 V, Vin = VDET− − 0.16 V
11. Condition 2: 0.9 − 4.9 V, Vin = VDET− + 2.0 V
12. Condition 3: 0.9 − 1.4 V, Vin = 1.5 V, VOUT = 0.5 V; 1.5 − 4.9 V, Vin = 5.0 V, VOUT = 0.5 V, Active High ‘H’ Suffix Devices
13. Condition 4: 0.9 − 4.9 V, Vin = 0.7 V, VOUT = 0.4 V, Active High ‘H’ Suffix Devices
14. Condition 5: 0.9 − 1.0 V, Vin = 0.8 V, VOUT = GND; 1.1 − 1.5 V, Vin = 1.0 V, VOUT = GND; 1.6 − 4.9 V, Vin = 1.5 V, VOUT = GND,
Active High ‘H’ Suffix Devices
www.onsemi.com
9
NCP304, NCP305
Table 3. NCP305 SERIES ELECTRICAL CHARACTERISTIC TABLE FOR 0.9 − 4.9 V
Detector Threshold
Supply Current
N−Channel
Sink Current
Detector Threshold
Hysteresis
Vin Low
Vin High
Vin Low
Vin High
VHYS (V)
Iin
(mA)
(Note 15)
Iin
(mA)
(Note 16)
IOUT
(mA)
(Note 17)
IOUT
(mA)
(Note 18)
VDET− (V)
Min
Typ
Max
Min
Typ
Max
Typ
Typ
Typ
Typ
NCP305LSQ09T1
0.882
0.9
0.918
0.027
0.045
0.063
0.8
0.9
0.05
0.5
NCP305LSQ15T1
1.470
1.5
1.530
0.045
0.075
0.105
NCP305LSQ16T1
1.568
1.6
1.632
0.048
0.080
0.112
NCP305LSQ17T1
1.666
1.7
1.734
0.051
0.085
0.119
NCP305LSQ18T1
1.764
1.8
1.836
0.054
0.090
0.126
NCP305LSQ20T1
1.960
2.0
2.040
0.060
0.100
0.140
NCP305LSQ22T1
2.156
2.2
2.244
0.066
0.110
0.154
NCP305LSQ23T1
2.254
2.3
2.346
0.069
0.115
0.161
NCP305LSQ24T1
2.352
2.4
2.448
0.072
0.120
0.168
NCP305LSQ25T1
2.450
2.5
2.550
0.075
0.125
0.175
NCP305LSQ26T1
2.548
2.6
2.652
0.078
0.130
0.182
NCP305LSQ27T1
2.646
2.7
2.754
0.081
0.135
0.189
NCP305LSQ28T1
2.744
2.8
2.856
0.084
0.140
0.196
NCP305LSQ29T1
2.842
2.9
2.958
0.087
0.145
0.203
NCP305LSQ30T1
2.940
3.0
3.060
0.090
0.150
0.210
NCP305LSQ31T1
3.038
3.1
3.162
0.093
0.155
0.217
NCP305LSQ32T1
3.136
3.2
3.264
0.096
0.160
0.224
NCP305LSQ33T1
3.234
3.3
3.366
0.099
0.165
0.231
NCP305LSQ34T1
3.332
3.4
3.468
0.102
0.170
0.238
NCP305LSQ35T1
3.430
3.5
3.570
0.105
0.175
0.245
NCP305LSQ36T1
3.528
3.6
3.672
0.108
0.180
0.252
NCP305LSQ37T1
3.626
3.7
3.774
0.111
0.185
0.259
NCP305LSQ40T1
3.920
4.0
4.080
0.120
0.200
0.280
NCP305LSQ44T1
4.312
4.4
4.488
0.132
0.220
0.308
NCP305LSQ45T1
4.410
4.5
4.590
0.135
0.225
0.315
NCP305LSQ47T1
4.606
4.7
4.794
0.141
0.235
0.329
NCP305LSQ49T1
4.802
4.9
4.998
0.147
0.245
0.343
Part Number
2.0
0.9
1.1
1.0
1.2
1.1
1.3
15. Condition 1: 0.9 − 2.9 V, Vin = VDET− − 0.10 V; 3.0 − 3.9 V, Vin = VDET− − 0.13 V; 4.0 − 4.9 V, Vin = VDET− − 0.16 V
16. Condition 2: 0.9 − 4.9 V, Vin = VDET− + 2.0 V
17. Condition 3: 0.9 − 4.9 V, Vin = 0.7 V, VOUT = 0.05 V, Active Low ‘L’ Suffix Devices
18. Condition 4: 0.9 − 1.0 V, Vin = 0.85 V, VOUT = 0.5 V; 1.1 − 1.5 V, Vin = 1.0 V, VOUT = 0.5 V; 1.6 − 4.9 V, Vin = 1.5 V, VOUT = 0.5 V,
Active Low ‘L’ Suffix Devices
www.onsemi.com
10
0.98
0.96
VDET+
0.94
0.92
VDET−
0.90
0.88
0.86
−50
−25
0
25
75
50
100
VDET, DETECTOR THRESHOLD VOLTAGE (V)
VDET, DETECTOR THRESHOLD VOLTAGE (V)
NCP304, NCP305
3.00
2.95
2.90
VDET+
2.85
2.80
2.75
VDET−
2.70
2.65
2.60
−50
Figure 3. NCP304/5 Series 0.9 V
Detector Threshold Voltage vs. Temperature
50
75
100
Figure 4. NCP304/5 Series 2.7 V
Detector Threshold Voltage vs. Temperature
1.0
4.9
VOUT, OUTPUT VOLTAGE (V)
VDET, DETECTOR THRESHOLD VOLTAGE (V)
25
TA, AMBIENT TEMPERATURE (°C)
TA, AMBIENT TEMPERATURE (°C)
4.8
VDET+
4.7
4.6
VDET−
4.5
4.4
4.3
−50
0.8
0.6
0.4
TA = −30°C
TA = 25°C
TA = 85°C
0.2
0
0
75
TA, AMBIENT TEMPERATURE (°C)
0.4
0.6
Vin, INPUT VOLTAGE (V)
Figure 5. NCP304/5 Series 4.5 V
Detector Threshold Voltage vs. Temperature
Figure 6. NCP304L/5L Series 0.9 V
Reset Output Voltage vs. Input Voltage
−25
25
50
0
100
0.2
0.8
1.0
7.0
VOUT, OUTPUT OUTPUT (V)
3.0
VOUT, OUTPUT OUTPUT (V)
0
−25
2.5
2.0
1.5
1.0
TA = −30°C
TA = 25°C
TA = 85°C
0.5
0
6.0
5.0
4.0
3.0
2.0
TA = −30°C
TA = 25°C
TA = 85°C
1.0
0
0
1.0
1.5
0.5
2.0
Vin, INPUT VOLTAGE (V)
2.5
3.0
0
1.0
2.0
4.0
3.0
Vin, INPUT VOLTAGE (V)
5.0
Figure 8. NCP304L/5L Series 4.5 V
Reset Output Voltage vs. Input Voltage
Figure 7. NCP304L/5L Series 2.7 V
Reset Output Voltage vs. Input Voltage
www.onsemi.com
11
6.0
NCP304, NCP305
1.2
IOUT, OUTPUT SINK CURRENT (mA)
VOUT, OUTPUT VOLTAGE (V)
3.0
2.5
2.0
1.5
1.0
TA = −30°C
TA = 25°C
0.5
0
TA = 85°C
0
0.5
1.0
1.5
2.0
2.5
Vin = 0.85 V
0.8
0.6
0.4
Vin = 0.7 V
0.2
0
3.0
0
0.6
1.0
0.8
VOUT, OUTPUT VOLTAGE (V)
Figure 9. NCP304H/5H Series 2.7 V
Reset Output Voltage vs. Input Voltage
Figure 10. NCP304H/5L Series 0.9 V
Reset Output Sink Current vs. Output Voltage
IOUT, OUTPUT SINK CURRENT (mA)
35
TA = 25°C
14
Vin = 2.5 V
12
10
8.0
Vin = 2.0V
6.0
4.0
Vin = 1.5 V
2.0
0
TA = 25°C
30
Vin = 4.0 V
25
Vin = 3.5 V
20
Vin = 3.0 V
15
Vin = 2.5 V
10
Vin = 2.0 V
5.0
Vin = 1.5 V
0
0
0.5
1.0
1.5
0
2.5
2.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
VOUT, OUTPUT VOLTAGE (V)
VOUT, OUTPUT VOLTAGE (V)
Figure 11. NCP304H/5L Series 2.7 V
Reset Output Sink Current vs. Output Voltage
Figure 12. NCP304H/5L Series 4.5 V
Reset Output Sink Current vs. Output Voltage
2.5
2.0
Vin = 2.5 V
2.0
Iin, INPUT CURRENT (mA)
IOUT, OUTPUT SOURCE CURRENT (mA)
0.4
0.2
Vin, INPUT VOLTAGE (V)
16
IOUT, OUTPUT SINK CURRENT (mA)
TA = 25°C
1.0
1.5
Vin = 2.0 V
1.0
Vin = 1.5 V
0.5
TA = 25°C
1.5
1.0
0.5
0
0
0
0.5
1.0
1.5
2.0
2.5
0
VOUT, OUTPUT VOLTAGE (V)
4.0
6.0
Vin, INPUT VOLTAGE (V)
Figure 13. NCP304H Series 2.7 V Reset Output
Source Current vs. Output Voltage
Figure 14. NCP304/5 Series 0.9 V
Input Current vs. Input Voltage
www.onsemi.com
12
2.0
8.0
10
NCP304, NCP305
2
2.0
TA = 25°C
Iin, INPUT CURRENT (mA)
Iin, INPUT CURRENT (mA)
TA = 25°C
1.5
1.0
0.5
0
1.5
1.0
0.5
0
0
2.0
4.0
6.0
Vin, INPUT VOLTAGE (V)
10
8.0
0
Figure 15. NCP304/5 Series 2.7 V
Input Current vs. Input Voltage
8.0
10
7.0
IOUT, OUTPUT SINK CURRENT (mA)
IOUT, OUTPUT SINK CURRENT (mA)
6.0
4.0
Vin, INPUT VOLTAGE (V)
Figure 16. NCP304/5 Series 4.5 V
Input Current vs. Input Voltage
1.4
1.2
1.0
0.8
0.6
TA = 85°C
0.4
TA = 25°C
0.2
TA = −30°C
0
0
0.4
0.2
0.6
6.0
5.0
TA = −30°C
4.0
TA = 25°C
TA = 85°C
3.0
2.0
1.0
0
0
1.0
0.8
0.5
1.0
1.5
2.0
2.5
Vin, INPUT VOLTAGE (V)
Vin, INPUT VOLTAGE (V)
Figure 17. NCP304H/5L Series 0.9 V
Reset Output Sink Current vs. Input Voltage
Figure 18. NCP304H/5L Series 2.7 V
Reset Output Sink Current vs. Input Voltage
3.0
90
IOUT, OUTPUT SINK CURRENT (mA)
12
IOUT, OUTPUT SINK CURRENT (mA)
2.0
10
TA = −30°C
8.0
TA = 25°C
6.0
TA = 85°C
4.0
2.0
80
70
60
Vout = Vin − 2.1 V
= Vin − 1.5 V
50
= Vin − 1.0 V
= Vin − 0.5 V
40
30
20
10
0
0
0
1.0
2.0
3.0
0
5.0
4.0
2.0
4.0
6.0
8.0
Vin, INPUT VOLTAGE (V)
Vin, INPUT VOLTAGE (V)
Figure 19. NCP304H/5L Series 4.5 V
Reset Output Sink Current vs. Input Voltage
Figure 20. NCP304H/5H Series 2.7 V
Reset Output Sink Current vs. Input Voltage
www.onsemi.com
13
10
12
IOUT, OUTPUT SOURCE CURRENT (mA)
IOUT, OUTPUT SOURCE CURRENT (mA)
NCP304, NCP305
VOUT = Vin −2.1 V
TA = 25°C
10
Vin −1.5 V
8.0
Vin −1.0 V
6.0
4.0
Vin − 0.5 V
2.0
0
0
2.0
4.0
6.0
8.0
10
12
VOUT = Vin −2.1 V
TA = 25°C
10
Vin −1.5 V
8.0
Vin −1.0 V
6.0
4.0
Vin − 0.5 V
2.0
0
0
Vin, INPUT VOLTAGE (V)
IOUT, OUTPUT SOURCE CURRENT (mA)
IOUT, OUTPUT SOURCE CURRENT (mA)
VOUT = Vin −2.1 V
TA = 25°C
Vin −1.5 V
8.0
Vin −1.0 V
4.0
Vin − 0.5 V
2.0
0
0
2.0
4.0
6.0
10
Figure 22. NCP304H Series 2.7 V
Reset Output Source Current vs. Input Voltage
12
6.0
8.0
6.0
Vin, INPUT VOLTAGE (V)
Figure 21. NCP304H Series 0.9 V
Reset Output Source Current vs. Input Voltage
10
4.0
2.0
8.0
10
4.0
TA = −30°C
3.0
TA = 25°C
2.0
TA = 85°C
1.0
0
0
0.5
1.0
1.5
2.0
2.5
3.0
Vin, INPUT VOLTAGE (V)
Vin, INPUT VOLTAGE (V)
Figure 24. NCP304H Series 2.7 V
Reset Output Source Current vs. Input Voltage
Figure 23. NCP304H Series 4.5 V
Reset Output Source Current vs. Input Voltage
www.onsemi.com
14
NCP304, NCP305
OPERATING DESCRIPTION
high state for active high devices. After completion of the
power interruption, Vin will again return to its nominal level
and become greater than the VDET+. The voltage detector
has built−in hysteresis to prevent erratic reset operation as
the comparator threshold is crossed.
Although these device series are specifically designed for
use as reset controllers in portable microprocessor based
systems, they offer a cost−effective solution in numerous
applications where precise voltage monitoring is required.
Figure 26 through Figure 32 shows various application
examples.
The NCP304 and NCP305 series devices are second
generation ultra−low current voltage detectors. Figures 25
and 26 show a timing diagram and a typical application.
Initially consider that input voltage Vin is at a nominal level
and it is greater than the voltage detector upper threshold
(VDET+), and the reset output (Pin 1) will be in the high state
for active low devices, or in the low state for active high
devices. If there is a power interruption and Vin becomes
significantly deficient, it will fall below the lower detector
threshold (VDET−). This sequence of events causes the Reset
output to be in the low state for active low devices, or in the
“L” in Part Name
“H” in Part Name
Function: active Low Reset Output
Function: active High Reset Output
Input < Vdet−, Reset Output is Low
Input < Vdet−, Reset Output is High
Input > Vdet+, Reset Output is High
Input > Vdet+, Reset Output is Low
Input Voltage, Pin 2
Reset Output (Active Low), Pin 1
Vin
VDET+
VDET−
Vin
VDET+
VDET−
0V
Reset Output (Active High), Pin 1
Vin
VDET+
VDET−
0V
Figure 25. Timing Waveforms
www.onsemi.com
15
NCP304, NCP305
APPLICATION CIRCUIT INFORMATION
VDD
VDD
2
Input
NCP304
Series
4
*
1
Microprocessor
Reset
Reset Output
* Required for
GND
GND
NCP305
Figure 26. Microprocessor Reset Circuit
2.85 V
2.70 V
Vin < 2.7 ON
2
Input
NCP304
LSQ27T1
1
To Additional Circuitry
Reset Output
Vin > 2.835 ON
4
GND
Figure 27. Battery Charge Indicator
Vsupply
5.0 V
2
Input
1
NCP305
LSQ45T1
Reset Output
4
GND
2
Input
3.3 V
1
NCP305
LSQ30T1
4
Reset Output
GND
Low state output if either
power supply is below the
respective undervoltage detector threshold but greater
than 1.0 V.
Figure 28. Dual Power Supply Undervoltage Supervision
www.onsemi.com
16
NCP304, NCP305
VDD
RH
2
VDD
Input
RL
1
NCP301
NCP305
LSQ27T1
LSN27T1
Reset
Reset Output
Microprocessor
GND
GND
4
Figure 29. Microprocessor Reset Circuit with Additional Hysteresis
Comparator hysteresis can be increased with the addition of
resistor RH. The hysteresis equations have been simplified and
do not account for the change of input current Iin as Vin crosses
the comparator threshold. The internal resistance, Rin is simply
calculated using Iin = 0.26 mA at 2.6 V.
Vin Decreasing:
V th +
ǒRR
H
Ǔ
) 1 ǒV DET*Ǔ
in
Vin Increasing:
V th +
ǒ
Ǔ
RH
) 1 ǒV DET* ) V HYSǓ
R in ø R L
VHYS = Vin Increasing − Vin Decreasing
Test Data
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Vth Decreasing
(mV)
Vth Increasing
(mV)
VHYS
(mV)
RH
(W)
RL
(kW)
2.70
2.70
2.70
2.70
2.70
2.70
2.70
2.70
2.70
2.70
2.84
2.87
2.88
2.91
2.90
2.94
2.98
2.70
3.04
3.15
0.135
0.17
0.19
0.21
0.20
0.24
0.28
0.27
0.34
0.35
0
100
100
100
220
220
220
470
470
470
−
10
6.8
4.3
10
6.8
4.3
10
6.8
4.3
5.0 V
100 k
Test Data
C
2
fOSC (kHz)
IQ (mA)
0.01
2590
21.77
1
0.1
490
21.97
Reset Output
1.0
52
22.07
82 k
NCP301
NCP302
HSQ27T1
LSN27T1
4
C (mF)
Input
GND
Figure 30. Simple Clock Oscillator
www.onsemi.com
17
NCP304, NCP305
Vsupply
This circuit monitors the current at the load. As
current flows through the load, a voltage drop with
respect to ground appears across Rsense where
Vsense = Iload * Rsense. The following conditions apply:
Load
VDD
Rsense
2
If:
ILoad t VDET − /Rsense
ILoad w (VDET −+VHYS)/Rsense
Input
50 k
NCP301
NCP305
LSQ09T1
LSN27T1
4
1
Then:
Reset Output = 0 V
Reset Output = VDD
Microcontroller
Reset Output
GND
GND
Figure 31. Microcontroller Systems Load Sensing
Vsupply
2
Input
NCP305
NCP301
LSQ45T1
LSN27T1
4
GND
2
Input
NCP305
NCP301
LSQ27T1
LSN27T1
4
GND
2
Input
1
Reset
Output
1
Reset
Output
Vin = 1.0 V to 10 V
NCP305
NCP301
LSQ18T1
LSN27T1
4
1
Reset
Output
GND
A simple voltage monitor can be constructed by connecting several voltage detectors as shown above. Each LED will
sequentially turn on when the respective voltage detector threshold (VDET− +VHYS) is exceeded. Note that detector
thresholds (VDET−) that range from 0.9 V to 4.9 V in 100 mV steps can be manufactured.
Figure 32. LED Bar Graph
www.onsemi.com
18
NCP304, NCP305
ORDERING INFORMATION
Device
Threshold
Voltage
Output
Type
Reset
Marking
NCP304LSQ09T1G
0.9
SHG
NCP304LSQ18T1G
1.8
SGX
NCP304LSQ20T1G
2.0
SGV
NCP304LSQ23T1G
2.3
SGR
NCP304LSQ25T1G
2.5
SGP
NCP304LSQ27T1G
2.7
SGN
NCP304LSQ280T1G
2.8
CAT
NCP304LSQ29T1G
2.9
SGK
NCP304LSQ30T1G
3.0
SGJ
NCV304LSQ30T1G*
3.0
NCP304LSQ33T1G
3.3
NCV304LSQ33T1G*
3.3
AGA
NCP304LSQ37T1G
3.7
SGB
NCP304LSQ38T1G
3.8
SGA
NCP304LSQ40T1G
4.0
SFY
NCP304LSQ42T1G
4.2
SFU
NCP304LSQ43T1G
4.3
SFV
NCP304LSQ45T1G
4.5
SFS
NCP304LSQ46T1G
4.6
SFR
NCP304LSQ47T1G
4.7
SFQ
NCP304HSQ09T1G
0.9
SNQ
NCP304HSQ18T1G
1.8
SNZ
NCP304HSQ20T1G
2.0
SOB
NCP304HSQ22T1G
2.2
SOD
NCP304HSQ27T1G
2.7
NCP304HSQ29T1G
2.9
SOK
NCP304HSQ30T1G
3.0
SOL
NCP304HSQ45T1G
4.5
SPA
NCP304HSQ47T1G
4.7
SPC
CMOS
CMOS
Active
Low
Active
High
Package
Shipping†
SC−82AB
(Pb−Free)
3000 / Tape & Reel
ACT
SGG
SOI
NOTE: The ordering information lists standard undervoltage thresholds with active low outputs. Additional active low threshold devices, ranging
from 0.9 V to 4.9 V in 100 mV increments and NCP304 active high output devices, ranging from 0.9 V to 4.9 V in 100 mV increments
can be manufactured. Contact your ON Semiconductor representative for availability. The electrical characteristics of these additional
devices are shown in Tables 1 and 2.
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.
*NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and
PPAP Capable.
NCVxxx: Tlow = −40°C, Thigh = +125°C. Guaranteed by design.
www.onsemi.com
19
NCP304, NCP305
ORDERING INFORMATION
Device
Threshold
Voltage
Output
Type
Reset
Marking
NCP305LSQ09T1G
0.9
NCP305LSQ11T1G
1.1
SIX
NCV305LSQ11T1G*
1.1
TAP
NCP305LSQ15T1G
1.5
SIS
NCP305LSQ16T1G
1.6
SIR
NCP305LSQ17T1G
1.7
SIQ
NCP305LSQ18T1G
1.8
SIP
NCP305LSQ20T1G
2.0
SIN
NCV305LSQ20T1G*
2.0
AAJ
NCP305LSQ22T1G
2.2
SIK
NCP305LSQ23T1G
2.3
SIJ
NCV305LSQ23T1G*
2.3
AUT
NCP305LSQ24T1G
2.4
SII
NCP305LSQ25T1G
2.5
SIH
NCP305LSQ26T1G
2.6
SIG
NCP305LSQ27T1G
2.7
Package
Shipping†
SIZ
3000 / Tape & Reel
SIF
Open
Drain
Active
Low
NCP305LSQ28T1G
2.8
SIE
NCP305LSQ29T1G
2.9
SID
NCP305LSQ30T1G
3.0
SIC
NCP305LSQ30T3G
3.0
SIC
NCP305LSQ31T1G
3.1
SIB
NCP305LSQ32T1G
3.2
SIA
NCP305LSQ33T1G
3.3
SHZ
NCP305LSQ34T1G
3.4
SHY
NCP305LSQ35T1G
3.5
SHX
NCP305LSQ36T1G
3.6
SHU
NCP305LSQ37T1G
3.7
SHV
NCP305LSQ40T1G
4.0
SHR
NCP305LSQ44T1G
4.4
SHN
NCV305LSQ44T1G*
4.4
AAH
NCP305LSQ45T1G
4.5
SHL
NCP305LSQ47T1G
4.7
SHJ
NCP305LSQ49T1G
4.9
SHH
SC−82AB
(Pb−Free)
10,000 / Tape & Reel
3000 / Tape & Reel
NOTE: The ordering information lists standard undervoltage thresholds with active low outputs. Additional active low threshold devices, ranging
from 0.9 V to 4.9 V in 100 mV increments and NCP304 active high output devices, ranging from 0.9 V to 4.9 V in 100 mV increments
can be manufactured. Contact your ON Semiconductor representative for availability. The electrical characteristics of these additional
devices are shown in Tables 1 and 2.
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.
*NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and
PPAP Capable.
NCVxxx: Tlow = −40°C, Thigh = +125°C. Guaranteed by design.
www.onsemi.com
20
NCP304, NCP305
PACKAGE DIMENSIONS
SC−82AB
SQ SUFFIX
CASE 419C−02
ISSUE F
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. 419C−01 OBSOLETE. NEW STANDARD IS
419C−02.
4. DIMENSIONS A AND B DO NOT INCLUDE
MOLD FLASH, PROTRUSIONS, OR GATE
BURRS.
A
G
C
D 3 PL
N
4
3
K
B
S
1
DIM
A
B
C
D
F
G
H
J
K
L
N
S
2
F
L
H
J
0.05 (0.002)
MILLIMETERS
MIN
MAX
1.80
2.20
1.15
1.35
0.80
1.10
0.20
0.40
0.30
0.50
1.10
1.50
0.00
0.10
0.10
0.26
0.10
−−−
0.05 BSC
0.20 REF
1.80
2.40
INCHES
MIN
MAX
0.071
0.087
0.045
0.053
0.031
0.043
0.008
0.016
0.012
0.020
0.043
0.059
0.000
0.004
0.004
0.010
0.004
−−−
0.002 BSC
0.008 REF
0.07
0.09
SOLDERING FOOTPRINT*
1.30
0.0512
0.65
0.026
1.90
0.95 0.075
0.037
0.90
0.035
0.70
0.028
SCALE 10:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and the
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed
at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation
or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets
and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each
customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended,
or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or
unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable
copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
21
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCP304/D