Features • Protocol – USB Used as Physical Layer – Device Firmware Upgrade Class Compliant – USB Clock Auto-Configuration • In-System Programming – Read/Write Flash and EEPROM Memories – Read Device ID – Full-chip Erase – Read/Write Configuration Bytes – Security Setting from ISP Command – Remote Application Start Command • In-Application Programming/Self Programming (IAP) – Read/Write Flash and EEPROM Memories – Read Device ID – Block Erase – Read/Write Configuration Bytes – Bootloader Start USB Microcontrollers AT89C5131A USB Bootloader Description This document describes the USB bootloader functionalities as well as the USB protocol to efficiently perform operations on the on-chip Flash (EEPROM) memories. Additional information on the AT89C5131A product can be found in the AT89C5131A datasheet and the AT89C5131A errata sheet available on the Atmel web site. The bootloader software package (binary) currently used for production is available from the Atmel web site. Bootloader Revision Purpose of Modifications Date Revision 1.0.2 First release 25/03/2003 Revision 1.2.0 Bootloader improvement 20/03/2007 4287E–USB–04/08 Functional Description The AT89C5131A bootloader facilitates In-System Programming and In-Application Programming. In-System Programming Capability (IAP) In-System Programming allows the user to program or reprogram a microcontroller on-chip Flash memory without removing it from the system and without the need of a pre-programmed application. The USB bootloader can manage a communication with a host through the USB bus. It can also access and perform requested operations on the on-chip Flash memory. In-Application Programming or Self Programming Capability (ISP) In-Application Programming (IAP) allows the reprogramming of a microcontroller on-chip Flash memory without removing it from the system and while the embedded application is running. Block Diagram This section describes the different parts of the bootloader. Figure 1 shows the on-chip bootloader and IAP processes. The USB bootloader contains some Application Programming Interface routines named API routines that allow IAP by using the user’s firmware. Figure 1. Bootloader Process Description On-chip User Application External Host Via the USB Protocol Communication IAP User Call Management ISP Communication Management Flash Memory Management Flash Memory 2 AT89C5131A USB Bootloader 4287E–USB–04/08 AT89C5131A USB Bootloader ISP Communication Management The purpose of this process is to manage the communication and its protocol between the onchip bootloader and an external device (host). The on-chip bootloader implements a USB protocol (see section “Protocol”). This process translates serial communication frames (USB) into Flash memory accesses (read, write, erase...). User Call Management Several Application Program Interface (API) calls are available to the application program to selectively erase and program Flash pages. All calls are made through a common interface (API calls) included in the bootloader. The purpose of this process is to translate the application request into internal Flash memory operations. Flash Memory Management This process manages low level access to the Flash memory (performs read and write access). Bootloader Configuration Configuration and Manufacturer Information The table below lists Configuration and Manufacturer byte information used by the bootloader. This information can be accessed through a set of API or ISP commands. Mnemonic Description Default Value BSB Boot Status Byte FFh SBV Software Boot Vector FCh SSB Software Security Byte FFh EB Extra Byte FFh P1_CF Port 1 Configuration FEh P3_CF Port 3 Configuration FFh P4_CF Port 4 Configuration FFh Manufacturer 58h Id1: Family code D7h Id2: Product Name F7h Id3: Product Revision DFh 3 4287E–USB–04/08 Mapping and Default Value of Hardware Security Byte The 4 MSB of the Hardware Byte can be read/written by software (this area is called Fuse bits). The 4 LSB can only be read by software and written by hardware in parallel mode (with parallel programmer devices). Note: Security Bit Position Mnemonic Default Value Description 7 X2B U To start in x1 mode 6 BLJB P To map the boot area in code area between F800h-FFFFh 5 OSCON1 U Oscillator control (bit 1) 4 OSCON0 U Oscillator control (bit 0) 3 reserved U 2 LB2 P 1 LB1 U 0 LB0 U To lock the chip (see datasheet) U: Unprogrammed = 1 P: Program = 0 The bootloader has Software Security Byte (SSB) to protect itself from user access or ISP access. The Software Security Byte (SSB) protects from ISP accesses. The command "Program Software Security Bit" can only write a higher priority level. There are three levels of security: • Level 0: NO_SECURITY (FFh) This is the default level. From level 0, one can write level 1 or level 2. • Level 1: WRITE_SECURITY (FEh) In this level it is impossible to write in the Flash memory. The Bootloader returns an err_WRITE status. From level 1, one can write only level 2. • Level 2: RD_WR_SECURITY (FCh) Level 2 forbids all read and write accesses to/from the Flash memory. The Bootloader returns an err_WRITE or an err_VENDOR status. Only a full chip erase command can reset the software security bits. 4 Level 0 Level 1 Level 2 Flash/EEPROM Any access allowed Read only access allowed All access not allowed Fuse bit Any access allowed Read only access allowed All access not allowed BSB & SBV & EB Any access allowed Any access allowed Any access allowed SSB Any access allowed Write level2 allowed Read only access allowed Manufacturer info Read only access allowed Read only access allowed Read only access allowed Bootloader info Read only access allowed Read only access allowed Read only access allowed Erase block Allowed Not allowed Not allowed Full chip erase Allowed Allowed Allowed Blank Check Allowed Allowed Allowed AT89C5131A USB Bootloader 4287E–USB–04/08 AT89C5131A USB Bootloader In-System Programming ISP allows the user to program or reprogram a microcontroller’s on-chip Flash memory through the USB bus without removing it from the system and without the need of a pre-programmed application. This section describes how to start the USB bootloader and the higher level protocol over the USB. Boot Process The bootloader can be activated in two ways: • Hardware conditions • Regular boot process Figure 3 and Figure 4 describe the boot process flows for low pin count and high pin count products. High Pin Count Hardware Conditions The Hardware conditions (EA = 1, PSEN = 0) during the RESET rising edge force the on-chip bootloader execution. In this way the bootloader can be carried out regardless of the user Flash memory content. It is recommended to pull the PSEN pin down to ground though a 1K resistor to prevent the PSEN pin from being damaged (see Figure 2 below). Figure 2. ISP Hardware conditions VCC VCC VCC EA ALE Unconnected C2 RST GND XTAL2 Bootloader Crystal XTAL1 /PSEN GND C1 1K GND GND VSS GND As PSEN is an output port in normal operating mode (running user application or bootloader code) after reset, it is recommended to release PSEN after rising edge of reset signal. The hardware conditions are sampled at reset signal rising edge, thus they can be released at any time when reset input is high. Low Pin Count Hardware Conditions The Hardware Condition forces the bootloader execution from reset. The default factory Hardware Condition is assigned to port P1. • P1 must be equal to FEh In order to offer the best flexibility, the user can define its own Hardware Condition on one of the following Ports: • Port1 5 4287E–USB–04/08 • Port3 • Port4 (only bit0 and bit1) The Hardware Condition configuration are stored in three bytes called P1_CF, P3_CF, P4_CF. These bytes can be modified by the user through a set of API or through an ISP command. There is a priority between P1_CF, P3_CF and P4_CF (see Figure 4 on page 9). Note: 6 The BLJB must be at 0 (programmed) to be able to restart the bootloader. If the BLJB is equal to 1 (unprogrammed) only the hardware parallel programmer can change this bit (see AT89C5131A datasheet for more details). AT89C5131A USB Bootloader 4287E–USB–04/08 AT89C5131A USB Bootloader Software Boot Vector The default value [FF]00h is used in ISP mode. The boot address is, in this mode, the lowest adress of FM1 USB bootloader. The Software Boot Vector (SBV) can be used to force the execution of a user bootloader starting at address [SBV]00h in the application area (FM0). The way to start this user bootloader is described in section “Boot Process”. USB Bootloader [FC]00h User Bootloader FM1 [SBV]00h Application FM0 FLIP Software Program FLIP is a PC software program running under Windows® 9x/Me/2000/XP and Linux® which can be used in ISP mode and which supports all Atmel C51 Flash microcontroller and USB protocol communication media. The FLIP software program is free and is available from the Atmel web site. 7 4287E–USB–04/08 Figure 3. High-pin Count Regular Boot Process B it E N B O O T in A U XR 1 R egis ter is Initialized with B LJ B inverted Hardware Boot Process RESET No ENBOOT = 0 P C = 0000h Y es B LJ B = 1 No Software Boot Process F C O N = 00h ENBOOT = 1 P C = F 400h F C O N = 0F h Y es No S B V < 7F h No Y es S ta rt A p p lica tio n 8 Y es H ardw are C ondition ENBOOT = 1 P C = F 400h F C O N = 00h S ta rt U se r B o o tlo a d e r S ta rt B o o tlo a d e r AT89C5131A USB Bootloader 4287E–USB–04/08 AT89C5131A USB Bootloader Figure 4. Low-pin Count Regular Boot Process Bit ENBOOT in AUXR1 Register is Initialized with BLJB Inverted Hardware Boot Process RESET ENBOOT = 0 PC = 0000h Yes BLJB = 1 No No No Software Boot Process Yes P1_CF = FFh No P1_CF = P1 Yes ENBOOT = 1 PC = F400h No P3_CF = P3 P3_CF = FFh No Yes P4_CF = FFh Yes Yes No Yes BSB = 0 P4_CF = P4 Yes No SBV < 7Fh No Yes Start Application Start User Bootloader Start Bootloader 9 4287E–USB–04/08 Physical Layer The USB norm specifies all the transfers over the USB line. The USB specification also includes several CLASS and SUB-CLASS specifications. These stand-alone documents are used by the manufacturer to implement a USB link between a PC and a device supporting the In System Programming. Mostly, the USB specification is implemented by hardware (automatic reply, handshakes, timings, ...) and the USB Classes and SubClasses are implemented by software at a data level. Figure 5. USB Bus Topography Downstream Transfer: OUT Upstream Transfer: IN Device driver/API Firmware PC Driver PC Application USB Line Application (Device) PC (Host) The USB is used to transmit information that has the following configuration: 48 MHz Frequency Auto-Configuration • USB DFU using the Default Control Endpoint only (endpoint 0) with a 32 bytes length. • 48 MHz for USB controller: USB clock configuration performed by the bootloader The bootloader includes a function which will automatically setup the PLL frequency (48MHz) versus the different XTAL configuration used on the application. The table below shows the allowed frequencies compatible with the USB bootloader 48 MHz auto-generation. X1 or X2 Clock Modes 10 6 MHz 8 MHz 12 MHz 16 MHz 20 MHz 24 MHz 32 MHz 40 MHz 48 MHz OK OK OK OK OK OK OK OK OK AT89C5131A USB Bootloader 4287E–USB–04/08 AT89C5131A USB Bootloader Figure 6. 48 MHz Frequency Auto-Configuration MAIN No No USB Connected? Suspend/Resume Yes Resume Detected? Configure PLL for Frequency X Configure Timer 0 Yes Yes SOF Detected? No Timer 0 Overflow? No Yes Change Frequency USB Scheduler 11 4287E–USB–04/08 Protocol Device Firmware Upgrade Introduction Device Firmware Upgrade is the mechanism for accomplishing the task of upgrading the device firmware. Any class of USB device can exploit this capability by supporting the requirements specified in this document. Because it is impractical for a device to concurrently perform both DFU operations and its normal run-time activities, those normal activities must cease for the duration of the DFU operations. Doing so means that the device must change its operating mode; i.e., a printer is not a printer while it is undergoing a firmware upgrade; it is a PROM programmer. However, a device that supports DFU is not capable of changing its mode of operation on its own. External (human or host operating system) intervention is required. DFU Specific Requests In addition of the USB standard requests, 7 DFU class-specific requests are employed to accomplish the upgrade operations (Table 1): Table 1. DFU Class-specific Requests bmRequestType bRequest wValue wIndex wLength Data 0010 0001b DFU_DETACH (0) wTimeout Interface (4) Zero none 0010 0001b DFU_DNLOAD (1) wBlock Interface (4) Length Firmware 1010 0001b DFU_UPLOAD (2) wBlock Interface (4) Length Firmware 1010 0001b DFU_GETSTATUS (3) Zero Interface (4) 6 Status 0010 0001b DFU_CLRSTATUS (4) Zero Interface (4) Zero none 1010 0001b DFU_GETSTATE (5) Zero Interface (4) 1 State 0010 0001b DFU_ABORT (6) Zero Interface (4) Zero none DFU Descriptors Set DFU Device Descriptor The device exports the DFU descriptor set, which contains: • A DFU device descriptor • A single configuration descriptor • A single interface descriptor (including descriptors for alternate settings, if present) • A single functional descriptor This descriptor is only present in the DFU mode descriptor set. The DFU class code is reported in the bDeviceClass field of this descriptor. Table 2. USB Parameters 12 Parameter Atmel – AT89C5131A Bootloader Vendor ID 0x03EB Product ID 0x2FFD Release Number 0x0000 AT89C5131A USB Bootloader 4287E–USB–04/08 AT89C5131A USB Bootloader Table 3. DFU Mode Device Descriptor Offset Field Size Value Description 0 bLength 1 12h Size of this descriptor, in bytes 1 bDescriptorType 1 01h DFU FUNCTIONAL descriptor type 2 bcdUSB 2 0100h 4 bDeviceClass 1 FEh Application Specific Class Code 5 bDeviceSubClass 1 01h Device Firmware Upgrade Code 6 bDeviceProtocol 1 00h The device does not use a class specific protocol on this interface 7 bMaxPacketSize0 1 32 Maximum packet size for endpoint zero 8 idVendor 2 03EBh Vendor ID 10 idProduct 2 2FFDh Product ID 12 bcdDevice 2 0x0000 Device release number in binary coded decimal 14 iManufacturer 1 0 Index of string descriptor 15 iProduct 1 0 Index of string descriptor 16 iSerialNumber 1 0 Index of string descriptor 17 bNumConfigurations 1 01h USB specification release number in binary coded decimal One configuration only for DFU DFU Configuration Descriptor This descriptor is identical to the standard configuration descriptor described in the USB DFU specification version 1.0, with the exception that the bNumInterfaces field must contain the value 01h. DFU Interface Descriptor This is the descriptor for the only interface available when operating in DFU mode. Therefore, the value of the bInterfaceNumber field is always zero. Table 4. DFU Mode Interface Descriptor Offset Field Size Value 0 bLength 1 09h Size of this descriptor, in bytes 1 bDescriptorType 1 04h INTERFACE descriptor type 2 bInterfaceNumber 1 00h Number of this interface 3 bAlternateSetting 1 00h Alternate setting(1) 4 bNumEndpoints 1 00h Only the control pipe is used 5 bInterfaceClass 1 FEh Application Specific Class Code 6 bInterfaceSubClass 1 01h Device Firmware Upgrade Code 7 bInterfaceProtocol 1 00h The device doesn’t use a class specific protocol on this interface iInterface 1 00h Index of the String descriptor for this interface 8 Note: Description 1. Alternate settings can be used by an application to access additional memory segments. In this case, it is suggested that each alternate setting employ a string descriptor to indicate the target memory segment; e.g., “EEPROM”. Details concerning other possible uses of alternate settings are beyond the scope of this document. However, their use is intentionally not restricted because the authors anticipate that implementers will devise additional creative uses for alternate settings. 13 4287E–USB–04/08 DFU Functional Descriptor Table 5. DFU Functional Descriptor Offset Field Size Value Description 0 bLength 1 07h Size of this descriptor, in bytes 1 bDescriptorType 1 21h DFU FUNCTIONAL descriptor type DFU Attributes: bit 7..3: reserved 2 bmAttributes 1 Bit mask bit 2: device is able to communicate via USB after Manifestation phase 1 = yes, 0 = no, must see bus reset bit 1: bitCanUpload : upload capable 1 = yes, 0 = no bit 0: bitCanDnload : download capable 1 = yes, 0 = no Time in milliseconds that the device will wait after receipt of the DFU_DETACH request. 3 wDetachTimeOut 2 Number 5 wTransferSize 2 Number Command Description If this time elapses without a USB reset, the device will terminate the Reconfiguration phase and revert back to normal operation. This represents the maximum time that the device can wait (depending on its timers, ...). The Host may specify a shorter timeout in the DFU_DETACH request. Maximum number of bytes that the device can accept per controlwrite transaction This protocol allows to: • Initiate the communication • Program the Flash or EEPROM Data • Read the Flash or EEPROM Data • Program Configuration Information • Read Configuration and Manufacturer Information • Erase the Flash • Start the application Overview of the protocol is detailed in Appendix-A. 14 AT89C5131A USB Bootloader 4287E–USB–04/08 AT89C5131A USB Bootloader Device Status The Host employs the DFU_GETSTATUS request to facilitate synchronization with the device. This status gives information on the execution of the previous request: in progress/OK/Fail/... Get Status bmRequestType bRequest wValue wIndex wLength Data 1010 0001b DFU_GETSTATUS (3) Zero Interface (4) 6 Status 0010 0001b DFU_CLRSTATUS (4) Zero Interface (4) Zero none The device responds to the DFU_GETSTATUS request with a payload packet containing the following data: Table 6. DFU_GETSTATUS Response Offset Field Size Value Description 0 bStatus 1 Numb er An indication of the status resulting from the execution of the most recent request. 1 bwPollTimeOut 3 Numb er Minimum time in milliseconds that the host should wait before sending a subsequent DFU_GETSTATUS. The purpose of this field is to allow the device to dynamically adjust the amount of time that the device expects the host to wait between the status phase of the next DFU_DNLOAD and the subsequent solicitation of the device’s status via DFU_GETSTATUS. 4 bState 1 Numb er An indication of the state that the device is going to enter immediately following transmission of this response. 5 iString 1 Index Index of status description in string table. Table 7. bStatus values Status Value Description OK 0x00 No error condition is present errTARGET 0x01 File is not targeted for use by this device errFILE 0x02 File is for this device but fails some vendor-specific verification test errWRITE 0x03 Device id unable to write memory errERASE 0x04 Memory erase function failed errCHECK_ERASED 0x05 Memory erase check failed errPROG 0x06 Program memory function failed errVERIFY 0x07 Programmed memory failed verification errADDRESS 0x08 Cannot program memory due to received address that is out of range errNOTDONE 0x09 Received DFU_DNLOAD with wLength = 0, but device does not think it has all the data yet. errFIRMWARE 0x0A Device’s firmware is corrupted. It cannot return to run-time operations errVENDOR 0x0B iString indicates a vendor-specific error 15 4287E–USB–04/08 Table 7. bStatus values (Continued) Status Value Description errUSBR 0x0C Device detected unexpected USB reset signaling errPOR 0x0D Device detected unexpected power on reset errUNKNOWN 0x0E Something went wrong, but the device does not know what it was errSTALLEDPK 0x0F Device stalled an unexpected request Table 8. bState Values State Value Description appIDLE 0 Device is running its normal application appDETACH 1 Device is running its normal application, has received the DFU_DETACH request, and is waiting for a USB reset dfuIDLE 2 Device is operating in the DFU mode and is waiting for requests dfuDNLOAD-SYNC 3 Device has received a block and is waiting for the Host to solicit the status via DFU_GETSTATUS dfuDNBUSY 4 Device is programming a control-write block into its non volatile memories dfuDNLOAD-IDLE 5 Device is processing a download operation. Expecting DFU_DNLOAD requests Device has received the final block of firmware from the Host and is waiting for receipt of DFU_GETSTATUS to begin the Manifestation phase dfuMANIFEST-SYNC 6 or device has completed the Manifestation phase and is waiting for receipt of DFU_GETSTATUS. Clear Status 16 dfuMANIFEST 7 Device is in the Manifestation phase. dfuMANIFEST-WAITRESET 8 Device has programmed its memories and is waiting for a USB reset or a power on reset. dfuUPLOAD-IDLE 9 The device is processing an upload operation. Expecting DFU_UPLOAD requests. dfuERROR 10 An error has occurred. Awaiting the DFU_CLRSTATUS request. Any time the device detects an error and reports an error indication status to the host in the response to a DFU_GETSTATUS request, it enters the dfuERROR state. The device cannot transition from the dfuERROR state, after reporting any error status, until after it has received a DFU_CLRSTATUS request. Upon receipt of DFU_CLRSTATUS, the device sets a status of OK and transitions to the dfuIDLE state. Only then is it able to transition to other states. bmRequestType bRequest wValue wIndex wLength Data 0010 0001b DFU_CLRSTATUS (4) Zero Interface (4) 0 None AT89C5131A USB Bootloader 4287E–USB–04/08 AT89C5131A USB Bootloader Device State DFU_ABORT request Programming the Flash or EEPROM Data This request solicits a report about the state of the device. The state reported is the current state of the device with no change in state upon transmission of the response. The values specified in the bState field are identical to those reported in DFU_GETSTATUS. bmRequestType bRequest wValue wIndex wLength Data 1010 0001b DFU_GETSTATE (5) Zero Interface (4) 1 State The DFU_ABORT request enables the device to exit from certain states and return to the DFU_IDLE state. The device sets the OK status on receipt of this request. For more information, see the corresponding state transition summary. bmRequestType bRequest wValue wIndex wLength Data 1010 0001b DFU_ABORT (6) Zero Interface (4) 0 None The firmware image is downloaded via control-write transfers initiated by the DFU_DNLOAD class-specific request. The host sends between bMaxPacketSize0 and wTransferSize bytes to the device in a control-write transfer. Following each downloaded block, the host solicits the device status with the DFU_GETSTATUS request. As described in the USB DFU Specification, "Firmware images for specific devices are, by definition, vendor specific. It is therefore required that target addresses, record sizes, and all other information relative to supporting an upgrade are encapsulated within the firmware image file. It is the responsibility of the device manufacturer and the firmware developer to ensure that their devices can consume these encapsulated data. With the exception of the DFU file suffix, the content of the firmware image file is irrelevant to the host." Firmware image: • 32 bytes: Command • X bytes: X is the number of byte (00h) added before the first significative byte of the firmware. The X number is calculated to align the beginning of the firmware with the flash page. X = start_address [32]. For example, if the start address is 00AFh (175d), X = 175 [32] = 15. • The firmware • The DFU Suffix on 16 Bytes. Table 9. DFU File Suffix Offset Field Size Value Description The CRC of the entire file, excluding dwCRC -0 dwCRC 4 Number -4 bLength 1 16 -5 ucDfuSignature 3 The length of this DFU suffix including dwCRC 5 : 44h 6 : 46h The unique DFU signature field 7 : 55h -8 bcdDFU 2 -10 idVendor 2 BCD 0100h ID DFU specification number The vendor ID associated with this file. Either FFFFh or must match device’s vendor ID 17 4287E–USB–04/08 Offset Field Size Value Description -12 idProduct 2 ID The product ID associated with this file. Either FFFFf or must match the device’s product ID -14 bcdDevice 2 BCD The release number of the device associated with this file. Either FFFFh or a BCD firmware release or version number Request From Host bmRequestType bRequest wValue wIndex wLength Data 0010 0001b DFU_DNLOAD (1) wBlock Interface (4) Length Firmware Write Command Command Identifier data[0] data[1] data[2] data[3] data[4] 00h Id_prog_start 01h Description Init FLASH programming start_address 01h end_address Init EEPROM programming The write command is 6 bytes long. In order to reach the USB specification of the Control type transfers, the write command is completed with 26 (= 32 - 6) non-significant bytes. The total length of the command is then 32 bytes, which is the length of the Default Control Endpoint. Firmware The firmware can now be downloaded to the device. In order to be in accordance with the Flash page size (128 bytes), X non-significant bytes are added before the first byte to program. The X number is calculated to align the beginning of the firmware with the Flash page. X = start_address [32]. For example, if the start address is 00AFh (175d), X = 175 [32] = 15. DFU Suffix The DFU suffix of 16 bytes are added just after the last byte to program. This suffix is reserved for future use. 18 AT89C5131A USB Bootloader 4287E–USB–04/08 AT89C5131A USB Bootloader Figure 7. Example of Firmware Download Zero Length DFU_DNLOAD Request SETUP DFU_DNLOAD OUT Prog_Start + (EP0 fifo length - 6) x 00h OUT X offset bytes + Firmware Packet 1 OUT Firmware Packet 2 OUT Firmware Packet n + DFU suffix IN ZLP The Host sends a DFU_DNLOAD request with the wLength field cleared to 0 to the device to indicate that it has completed transferring the firmware image file. This is the final payload packet of a download operation. This operation should be preceded by a Long Jump address specification using the corresponding Flash command. Answers from Bootloader After each program request, the Host can request the device state and status by sending a DFU_GETSTATUS message. If the device status indicates an error, the host can send a DFU_CLRSTATUS request to the device. 19 4287E–USB–04/08 Reading the Flash or EEPROM Data The flow described below allows the user to read data in the Flash memory or in the EEPROM data memory. A blank check command on the Flash memory is possible with this flow. This operation is performed in 2 steps: 1. DFU_DNLOAD request with the read command (6 bytes) 2. DFU_UPLOAD request which correspond to the immediate previous command. First Request from Host The Host sends a DFU Download request with a Display command in the data field. SETUP DFU_DNLOAD OUT Display_Data (6 bytes) IN ZLP Command Identifier data[0] data[1] data[2] data[3] data[4] 00h Id_display_data 03h 01h Description Display FLASH Data start_address 02h end_address Blank Check in FLASH Display EEPROM Data Second Request from Host The Host sends a DFU Upload request. Answers from the Device The device send to the Host the firmware from the specified start address to the end address. 20 SETUP DFU_UPLOAD IN Firmware Packet 1 IN Firmware Packet 2 IN Firmware Packet n OUT ZLP AT89C5131A USB Bootloader 4287E–USB–04/08 AT89C5131A USB Bootloader Answers from the Device to a Blank Check Command Programming Configuration Information The Host controller send a GET_STATUS request to the device. Once internal blank check has been completed, the device sends its status. • If the device status is “OK”: the device memory is then blank and the device waits the next Host request. • If the device status is “errCHECK_ERASED”: the device memory is not blank. The device waits for an DFU_UPLOAD request to send the first address where the byte is not 0xFF. The flow described below allows the user to program Configuration Information regarding the bootloader functionality. • Boot Process Configuration: – BSB – SBV – P1_CF, P3_CF and P4_CF – Fuse bits (BLJB, X2 and OSCON bits) (see section “Mapping and Default Value of Hardware Security Byte”) Take care that the Program Fuse bit command programs the 4 Fuse bits at the same time. Request from Host To start the programming operation, the Host sends DFU_DNLOAD request with the Write command in the data field (6 bytes). DFU_DNLOAD SETUP Write_command (6 bytes) OUT ZLP IN Command Identifier data[0] 01h data[1] data[2] data[3] data[4] Description 00h Write value in BSB 01h Write value in SBV 02h Write P1_CF 03h Value Write P3_CF Id_write_command 04h 02h Answers From Bootloader 04h Write P4_CF 05h Write value in SSB 06h Write value in EB 00h Value Write value in Fuse (HSB) The device has two possible answers to a DFU_GETSTATUS request: • If the chip is protected from program access, a “err_WRITE” status is returned to the Host. • Otherwise, the device status is “OK“. 21 4287E–USB–04/08 Reading Configuration Information or Manufacturer Information The flow described below allows the user to read the configuration or manufacturer information. Requests From Host To start the programming operation, the Host sends DFU_DNLOAD request with the Read command in the data field (2 bytes). DFU_DNLOAD SETUP Read_command (2 bytes) OUT ZLP IN Command Identifier data[0] 00h Id_read_command 05h 01h 02h 22 data[1] data[2] data[3] data[4] Description 00h Read Bootloader Version 01h Read Device boot ID1 02h Read Device boot ID2 00h Read BSB 01h Read SBV 02h Read P1_CF 03h Read P3_CF 04h Read P4_CF 05h Read SSB 06h Read EB 30h Read Manufacturer Code 31h Read Family Code 60h Read Product Name 61h Read Product Revision 00h Read HWB AT89C5131A USB Bootloader 4287E–USB–04/08 AT89C5131A USB Bootloader Answers from Bootloader The device has two possible answers to a DFU_GETSTATUS request: • If the chip is protected from program access, an “err_VENDOR” status is returned to the Host. • Otherwise, the device status is “OK“. The Host can send a DFU_UPLOAD request to the device in order the value of the requested field. DFU_UPLOAD SETUP Byte value (1 byte) IN ZLP OUT Erasing the Flash The flow described below allows the user to erase the Flash memory. Two modes of Flash erasing are possible: • Full Chip erase • Block erase The Full Chip erase command erases the whole Flash (32 Kbytes) and sets some Configuration Bytes at their default values: • BSB = FFh • SBV = FFh • SSB = FFh (NO_SECURITY) The Block erase command erases only a part of the Flash. Three Blocks are defined in the AT89C5131A: Request from Host • block0 (From 0000h to 1FFFh) • block1 (From 2000h to 3FFFh) • block2 (From 4000h to 7FFFh) To start the erasing operation, the Host sends a DFU_DNLOAD request with a Write Command in the data field (2 bytes). Command Identifier Id_write_command 04h data[0] 00h data[1] data[2] data[3] data[4] Description 00h Erase block0 (0K to 8K) 20h Erase block1 (8K to 16K) 40h Erase block2 (16K to 32K) FFh Full chip Erase (bits at FFh) 23 4287E–USB–04/08 Answers from Bootloader The device has two possible answers to a DFU_GETSTATUS request: • If the chip is protected from program access, a “err_WRITE” status is returned to the Host. • Otherwise, the device status is “OK“. The full chip erase is always executed whatever the Software Security Byte value is. Starting the Application The flow described below allows to start the application directly from the bootloader upon a specific command reception. Two options are possible: • Start the application with a reset pulse generation (using watchdog). When the device receives this command the watchdog is enabled and the bootloader enters a waiting loop until the watchdog resets the device. Take care that if an external reset chip is used the reset pulse in output may be wrong and in this case the reset sequence is not correctly executed. • Start the application without reset A jump at the address 0000h is used to start the application without reset. To start the application, the Host sends a DFU_DNLOAD request with the specified application start type in the data field (3 or 5bytes). This request is immediately followed by a second DFU_DNLOAD request with no data field to start the application with one of the 2 options. Request From Host DFU_UPLOAD SETUP Jump Option (3 or 5 Bytes) IN OUT ZLP SETUP DFU_UPLOAD Command Identifier data[0] Id_write_command 04h data[1] data[2] data[3] 00h data[4] Description Hardware reset 03h 01h address LJMP address Answer from Bootloader No answer is returned by the device. 24 AT89C5131A USB Bootloader 4287E–USB–04/08 AT89C5131A USB Bootloader In-Application Programming/S elf Programming The IAP allows to reprogram a microcontroller on-chip Flash memory without removing it from the system and while the embedded application is running. The user application can call Application Programming Interface (API) routines allowing IAP. These API are executed by the bootloader. To call the corresponding API, the user must use a set of Flash_api routines which can be linked with the application. Example of Flash_api routines are available on the Atmel web site on the software package: C Flash Drivers for the AT89C5131A for Keil® Compilers The flash_api routines on the package work only with the USB bootloader. The flash_api routines are listed in APPENDIX-B. API Call Process The application selects an API by setting the 4 variables available when the flash_api library is linked to the application. These four variables are located in RAM at fixed address: • api_command: 1Ch • api_value: 1Dh • api_dph: 1Eh • api_dpl: 1Fh All calls are made through a common interface “USER_CALL” at the address FFC0h. The jump at the USER_CALL must be done by LCALL instruction to be able to comeback in the application. Before jump at the USER_CALL, the bit ENBOOT in AUXR1 register must be set. Constraints The interrupts are not disabled by the bootloader. Interrupts must be disabled by user prior to jump to the USER_CALL, then re-enabled when returning. Interrupts must also be disabled before accessing EEPROM data then re-enabled after. The user must take care of hardware watchdog before launching a Flash operation. For more information regarding the Flash writing time see the AT89C5131A datasheet. 25 4287E–USB–04/08 API Commands Read/Program Flash and EEPROM Data Memory Several types of APIs are available: • Read/Program Flash and EEPROM Data Memory • Read Configuration and Manufacturer Information • Program Configuration Information • Erase Flash • Start Bootloader All routines to access EEPROM data are managed directly from the application without using bootloader resources. To read the Flash memory the bootloader is not involved. For more details on these routines see the AT89C5131A datasheet sections “Program/Code Memory” and “EEPROM Data Memory” Two routines are available to program the Flash: – __api_wr_code_byte – __api_wr_code_page • The application program load the column latches of the Flash then calls the __api_wr_code_byte or __api_wr_code_page see datasheet in section “Program/Code Memory”. • Parameter settings API Name __api_wr_code_byte __api_wr_code_page • api_dph api_dpl api_value 0Dh instruction: LCALL FFC0h. Note: 26 api_command No special resources are used by the bootloader during this operation AT89C5131A USB Bootloader 4287E–USB–04/08 AT89C5131A USB Bootloader Read Configuration and Manufacturer Information • Parameter settings API Name api_command api_dph api_dpl api_value __api_rd_HSB 08h 00h return HSB __api_rd_BSB 05h 00h return BSB __api_rd_SBV 05h 01h return SBV __api_rd_P1_CF 05h 02h return P1_CF __api_rd_P3_CF 05h 03h return P3_CF __api_rd_P4_CF 05h 04h return P4_CF __api_rd_SSB 05h 05h return SSB __api_rd_EB 05h 06h return EB __api_rd_manufacturer 05h 30h return manufacturer id __api_rd_device_id1 05h 31h return id1 __api_rd_device_id2 05h 60h return id2 __api_rd_device_id3 05h 61h return id3 __api_rd_bootloader_version 0Eh 00h return value • Instruction: LCALL FFC0h. • At the complete API execution by the bootloader, the value to read is in the api_value variable. Note: No special resources are used by the bootloader during this operation 27 4287E–USB–04/08 Program Configuration Information • Parameter settings API Name • api_dph api_dpl api_value (HSB & BFh) | __api_clr_BLJB 07h __api_set_BLJB 07h __api_clr_X2 07h __api_set_X2 07h __api_clr_OSCON1 07h __api_set_OSCON1 07h __api_clr_OSCON0 07h __api_set_OSCON0 07h __api_wr_BSB 04h 00h value to write __api_wr_SBV 04h 01h value to write __api_wr_P1_CF 04h 02h value to write __api_wr_P3_CF 04h 03h value to write __api_wr_P4_CF 04h 04h value to write __api_wr_SSB 04h 05h value to write __api_wr_EB 04h 06h value to write 40h HSB & BFh (HSB & 7Fh) | 80h HSB & 7Fh (HSB & DFh) | 20h HSB & DFh (HSB & EFh) | 10h HSB & EFh instruction: LCALL FFC0h. Notes: Erasing the Flash api_command 1. See in the T89C51CC01 datasheet the time that a write operation takes. 2. No special resources are used by the bootloader during these operations. The AT89C5131A Flash memory is divided in several blocks: Block 0: from address 0000h to 1FFFh Block 1: from address 2000h to 3FFFh Block 2: from address 4000h to 7FFFh These three blocks contain 128 pages. • Parameter settings API Name • api_command api_dph __api_erase_block0 00h 00h __api_erase_block1 00h 20h __api_erase_block2 00h 40h api_value instruction: LCALL FFC0h. Notes: 28 api_dpl 1. See the AT89C5131A datasheet for the time that a write operation takes and this time must multiply by the number of pages. 2. No special resources are used by the bootloader during these operations. AT89C5131A USB Bootloader 4287E–USB–04/08 AT89C5131A USB Bootloader Starting the Bootloader This routine allows to start at the beginning of the bootloader as after a reset. After calling this routine the regular boot process is performed and the communication must be opened before any action. • No special parameter setting • Set bit ENBOOT in AUXR1 register • instruction: LJUMP or LCALL at address F400h 29 4287E–USB–04/08 Appendix-A Table 10. Summary of Frames from Host Command Identifier data[0] data[1] data[2] data[3] data[4] Description Id_prog_start 00h 01h 01h Init EEPROM programming 00h Display FLASH Data Id_display_data 03h Init FLASH programming start_address 01h end_address start_address end_address 02h Blank Check in FLASH Display EEPROM Data 00h Erase block0 (0K to 8K) 20h Erase block1 (8K to 16K) 40h Erase block2 (16K to 32K) FFh Full chip Erase (bits at FFh) 00h Write value in BSB 01h Write value in SBV 02h Write P1_CF 00h Id_write_command 04h 01h 02h 03h Value Write P3_CF 04h Write P4_CF 05h Write value in SSB 06h Write value in EB 00h Value Write value in Fuse (HSB) 00h Hardware reset 03h 01h 30 address LJMP address AT89C5131A USB Bootloader 4287E–USB–04/08 AT89C5131A USB Bootloader Table 10. Summary of Frames from Host (Continued) Command Identifier data[0] 00h Id_read_command 05h 01h 02h data[1] data[2] data[3] data[4] Description 00h Read Bootloader Version 01h Read Device boot ID1 02h Read Device boot ID2 00h Read BSB 01h Read SBV 02h Read P1_CF 03h Read P3_CF 04h Read P4_CF 05h Read SSB 06h Read EB 30h Read Manufacturer Code 31h Read Family Code 60h Read Product Name 61h Read Product Revision 00h Read HWB Table 11. DFU Class-specific Requests bmRequestType bRequest wValue wIndex wLength Data 0010 0001b DFU_DETACH (0) wTimeout Interface (4) Zero none 0010 0001b DFU_DNLOAD (1) wBlock Interface (4) Length Firmware 1010 0001b DFU_UPLOAD (2) wBlock Interface (4) Length Firmware 1010 0001b DFU_GETSTATUS (3) Zero Interface (4) 6 Status 0010 0001b DFU_CLRSTATUS (4) Zero Interface (4) Zero none 1010 0001b DFU_GETSTATE (5) Zero Interface (4) 1 State 0010 0001b DFU_ABORT (6) Zero Interface (4) Zero none Table 12. USB Parameters Parameter Atmel Vendor ID 0x03EB Product ID 0x2FFD Release Number 0x0000 Table 13. Hardware Security Byte (HSB) 7 6 5 4 X2 BLJB OSCON1 OSCON0 3 2 1 0 LB2 LB1 LB0 31 4287E–USB–04/08 Appendix-2 Table 14. API Summary Function Name Bootloader Execution api_command api_dph api_dpl api_value 00h return value __api_rd_code_byte no __api_wr_code_byte yes 0Dh __api_wr_code_page yes 0Dh __api_erase block0 yes 00h 00h __api_erase block1 yes 00h 20h __api_erase block2 yes 00h 40h __api_rd_HSB yes 08h __api_clr_BLJB yes 07h (HSB & BFh) | 40h __api_set_BLJB yes 07h HSB & BFh __api_clr_X2 yes 07h (HSB & 7Fh) | 80h __api_set_X2 yes 07h HSB & 7Fh __api_clr_OSCON1 yes 07h (HSB & DFh) | 20h __api_set_OSCON1 yes 07h HSB & DFh __api_clr_OSCON0 yes 07h (HSB & EFh) | 10h __api_set_OSCON0 yes 07h HSB & EFh __api_rd_BSB yes 05h 00h return value __api_wr_BSB yes 04h 00h value __api_rd_SBV yes 05h 01h return value __api_wr_SBV yes 04h 01h value __api_erase_SBV yes 04h 01h FFh __api_rd_P1_CF yes 05h 02h return value __api_wr_P1_CF yes 04h 02h value __api_rd_P3_CF yes 05h 03h return value __api_wr_P3_CF yes 04h 03h value __api_rd_P4_CF yes 05h 04h return value __api_wr_P4_CF yes 04h 04h value __api_rd_SSB yes 05h 05h return value __api_wr_SSB yes 04h 05h value __api_rd_EB yes 05h 06h return value __api_wr_EB yes 04h 06h value __api_rd_manufacturer yes 05h 30h return value __api_rd_device_id1 yes 05h 31h return value 32 AT89C5131A USB Bootloader 4287E–USB–04/08 AT89C5131A USB Bootloader Table 14. API Summary (Continued) Bootloader Execution api_command __api_wr_code_page yes 01h __api_rd_device_id2 yes __api_rd_device_id3 Function Name api_dph api_dpl api_value 05h 60h return value yes 05h 61h return value __api_rd_bootloader_version yes 0Eh 00h return value __api_eeprom_busy no __api_rd_eeprom_byte no __api_wr_eeprom_byte no __api_start_bootloader no __api_start_isp no 33 4287E–USB–04/08 Headquarters International Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Atmel Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369 Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309 78054 Saint-Quentin-enYvelines Cedex France Tel: (33) 1-30-60-70-00 Fax: (33) 1-30-60-71-11 Atmel Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Technical Support [email protected] Sales Contact www.atmel.com/contacts Product Contact Web Site www.atmel.com Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. © 2008 Atmel Corporation. All rights reserved. Atmel ®, logo and combinations thereof, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. 4287E–USB–04/08