AVAGO ACPL-K63L High speed lvttl compatible 3.3 volt/5 volt optocoupler Datasheet

ACPL-W60L and ACPL-K63L
High Speed LVTTL Compatible 3.3 Volt/5 Volt Optocouplers
Data Sheet
Lead (Pb) Free
RoHS 6 fully
compliant
RoHS 6 fully compliant options available;
-xxxE denotes a lead-free product
Description
Features
The ACPL-W60L/K63L are optically coupled gates that
combine a GaAsP light emitting diode and an integrated
high gain photo detector. The output of the detector IC is
an open collector Schottky-clamped transistor. The internal
shield provides a guaranteed common mode transient
immunity specification of 15 kV/µs at 3.3 V.
• Dual Voltage Operation (3.3V/5V)
This unique design provides maximum AC and DC circuit
isolation while achieving LVTTL/LVCMOS compatibility.
The optocoupler AC and DC operational parameters are
guaranteed from –40 °C to +85 °C allowing trouble-free
system performance.
• High speed: 15 MBd typical
Functional Diagram
ACPL-W60L
1
6
V CC
NC
2
5
VO
CATHODE
3
4
GND
SHIELD
ANODE 1 1
• Low power consumption
• 15 kV/µs minimum Common Mode Rejection (CMR)
at VCM = 1000V
• LVTTL/LVCMOS compatible
• Low input current capability: 5 mA
• Guaranteed AC and DC performance over temperature: –40 °C to +85 °C
• Available in 6-pin stretched SO-6 and 8 pin stretched
SO-8
ACPL-K63L
ANODE
• Package clearance/creepage at 8 mm
8
V CC
• Safety approvals: UL, CSA, IEC/EN/DIN EN 60747-5-5
CATHODE 1
2
7
V O1
Applications
CATHODE 2
3
6
V O2
• Isolated line receiver
5
GND
• Computer-peripheral interfaces
ANODE 2 4
SHIELD
TRUTH TABLE
(POSITIVE LOGIC)
LED
ON
OFF
OUTPUT
L
H
A 0.1 µF bypass capacitor must be connected between pins 4 and 6 for
ACPL-W60L, and pins 5 and 8 for ACPL-K63L.
• Microprocessor system interfaces
• Digital isolation for A/D, D/A conversion
• Switching power supply
• Instrument input/output isolation
• Ground loop elimination
• Pulse transformer replacement
• Fieldbus
CAUTION: It is advised that normal static precautions be taken in handling and assembly
of this component to prevent damage and/or degradation which may be induced by ESD.
Schematic Diagrams
IF
ACPL-W60L
ACPL-K63L
ICC
6
1+
IO
5
VCC
1
VO
ICC
8
IF1
IO1
+
7
VCC
VO1
VF1
VF
–
–
3
4
SHIELD
2
GND
SHIELD
3
IO2
–
USE OF A 0.1 µF BYPASS CAPACITOR CONNECTED
BETWEEN PINS 5 AND 8 IS RECOMMENDED (SEE NOTE 5).
6
VO2
VF2
+
4
IF2
5
SHIELD
These optocouplers are suitable for high speed logic
interfacing, input/output buffering, as line receivers in
environments that conventional line receivers cannot
tolerate and are recom­mended for use in extremely high
ground or induced noise environments.
GND
These optocouplers are available in stretched SO-6 and
SO-8 package. The part numbers are as follows:
Part number
Package
ACPL-W60L
ACPL-K63L
Stretched SO-6
Stretched SO-8
Ordering Information
ACPL-W60L/-K63L is UL Recognized with 5000 Vrms for 1 minute per UL1577 and is approved under CSA Component
Acceptance Notice #5, File CA 88324.
Option
Part
Number
ACPL-W60L
ACPL-K63L
RoHS Compliant
Package
Surface
Mount
Tape &
Reel
UL 5000 Vrms/
1 Minute rating
IEC/EN/DIN
EN 60747-5-5
Quantity
-000E
Stretched
X
X
100 per tube
-500E
SO-6
X
X
X
1000 per reel
-560E
X
X
X
1000 per reel
-000E
Stretched
X
X
80 per tube
-500E
SO-8
X
X
X
1000 per reel
X
X
X
1000 per reel
-560E
X
X
To order, choose a part number from the part number column and combine with the desired option from the option
column to form an order entry.
Example 1:
ACPL-W60L-560E to order product of Stretched SO-6 Surface Mount package in Tape and Reel packaging with
IEC/EN/DIN EN 60747-5-5 Safety Approval in RoHS compliant.
Option datasheets are available. Contact your Avago sales representative or authorized distributor for information.
2
Package Outline Drawings
ACPL-W60L Stretched SO-6 Package
LAND PATTERN RECOMMENDATION
12.65 (0.498)
1.27 (0.050) BSG
0.381 ± 0.127
(0.015 ± 0.005)
1
6
2
5
3
4
+0.127
0
+ 0.005
( 0.268 - 0.000 )
0.76 (0.030)
+ 0.254
0
+ 0.010
0.180
(
- 0.000 )
4.580
6.807
0.45 (0.018)
7°
1.91 (0.075)
1.59 ± 0.127
(0.063 ± 0.005)
7°
45°
3.180 ± 0.127
(0.125 ± 0.005)
0.20 ± 0.10
(0.008 ± 0.004)
0.750 ± 0.250
(0.0295 ± 0.010)
DIMENSIONS IN MILLIMETERS (INCHES).
11.5 ± 0.250
(0.453 ± 0.010)
LEAD COPLANARITY = 0.1 mm (0.004 INCHES).
ACPL-K63L Stretched SO-8 Package
LAND PATTERN RECOMMENDATION
12.650 (0.5)
1.270 (0.050) BSG
0.381 ± 0.13
(0.015 ± 0.005)
1
8
2
7
3
6
4
5
+ 0.25
0
+ 0.010
( 0.230 - 0.000 )
5.850
1.905 (0.1)
0.450 (0.018)
7°
1.590 ± 0.127
(0.063 ± 0.005)
7°
45°
3.180 ± 0.127
(0.125 ± 0.005)
0.200 ± 0.100
(0.008 ± 0.004)
6.807 ± 0.127
(0.268 ± 0.005)
0.750 ± 0.250
(0.0295 ± 0.010)
11.5 ± 0.250
(0.453 ± 0.010)
3
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.1 mm (0.004 INCHES).
Recommended Solder Reflow Thermal Profile
Recommended reflow condition as per JEDEC Standard, J-STD-020 (latest revision). Non-Halide Flux should be used.
Regulatory Information
The ACPL-W60L/K63L have been approved by the following organizations:
UL
Approval under UL 1577, Component Recognition Program, File E55361.
CSA
Approval under CSA Component Acceptance Notice #5, File CA 88324.
IEC/EN/DIN EN 60747-5-5
Insulation and Safety Related Specifications
Parameter
Symbol
ACPL-W60L/K63L
Units
Minimum External Air
L (101)
8
mm
Gap (External Clearance)
Minimum External Tracking
L (102)
8
mm
(External Creepage)
Minimum Internal Plastic
0.08
mm
Gap (Internal Clearance)
Tracking Resistance
CTI
175
Volts
(Comparative Tracking Index)
Isolation Group
IIIa
Conditions
Measured from input terminals to output
terminals, shortest distance through air.
Measured from input terminals to output
terminals, shortest distance path along body.
Through insulation distance, conductor to
conductor, usually the direct distance
between the photoemitter and photodetector
inside the optocoupler cavity.
DIN IEC 112/VDE 0303 Part 1
Material Group (DIN VDE 0110, 1/89, Table 1)
IEC/EN/DIN EN 60747-5-5 Insulation Related Characteristics
Description
Symbol
Characteristic
ACPL-W60L
ACPL-K63L
Units
Installation classification per DIN VDE 0110/39, Table 1
for rated mains voltage ≤ 150 VrmsI-IV
for rated mains voltage ≤ 300 VrmsI-IV
for rated mains voltage ≤ 600 VrmsI-III
for rated mains voltage ≤ 1000 VrmsI-III
Climatic Classification
55/85/21
Pollution Degree (DIN VDE 0110/39)
2
Maximum Working Insulation Voltage
1140
Vpeak
Input to Output Test Voltage, Method b*
VIORM x 1.875 = VPR, 100% Production Test with tm = 1 sec, VPR
Partial Discharge < 5 pC
2137
Vpeak
Input-to-Output Test Voltage, Method a*
VIORM x 1.6 = VPR, Type and Sample Test, tm = 10 sec,
Partial Discharge < 5 pC
VPR
1824
Vpeak
VIOTM
8000
Vpeak
Safety Limiting Values – maximum values allowed in the event of a failure
Case Temperature
TS
Input Current
IS,INPUT
Output Power
PS,OUTPUT
175
230
600
°C
mA
mW
Insulation Resistance at TS, VIO = 500 V
≥ 109
Ω
Highest Allowable Overvoltage
(Transient Overvoltage, tini = 60 sec)
VIORM
RS
* Refer to the optocoupler section of the Isolation and Control Components Designer’s Catalog, under Product Safety Regulations section, (IEC/
EN/DIN EN 60747-5-5) for a detailed description of Method a and Method b partial discharge test profiles.
4
Absolute Maximum Ratings (No Derating Required up to 85˚C)
Parameter
Symbol
Min.
Max.
Units
Storage Temperature
TS
–55
125
˚C
Operating Temperature†
TA
–40
85
˚C
Average Forward Input Current
IF
Device**
ACPL-W60L
ACPL-K63L
20
mA
15
2
1, 3
Reverse Input Voltage
VR 5
Input Power Dissipation
PI
Supply Voltage (1 Minute Maximum)
VCC 7
V
Output Collector Current
IO
mA
1
Output Collector Voltage
VO 7
V
1
Output Power Dissipation
PO
ACPL-W60L
ACPL-K63L
Solder Reflow Temperature Profile
Recommended Operating Conditions
Parameter
Symbol
Min.
Max.
Units
Input Current, Low Level
IFL*
0
250
µA
Input Current, High Level[1]
IFH**
5
15
mA
Power Supply Voltage
VCC
2.7
4.5
3.6
5.5
V
V
Operating Temperature
TA
–40
85
˚C
Fan Out (at RL = 1 kΩ)[1]
N
5
TTL Loads
Output Pull-up Resistor
RL
4k
Ω
*The off condition can also be guaranteed by ensuring that VFL ≤ 0.8 volts.
**The initial switching threshold is 5 mA or less. It is recommended that 6.3 mA to 10 mA be
used for best performance and to permit at least a 20% LED degradation guardband.
5
50
1
mW
85
mW
60
See Package Outline Drawings section
**Ratings apply to all devices except otherwise noted in the Package column.
330
40
V
Note
1, 4
Electrical Specifications
Over Recommended Operating Conditions (TA = –40°C to +85°C , 2.7V ≤ Vcc ≤ 3.6V) unless otherwise specified.
All Typicals at VCC = 3.3 V, TA = 25˚C.
Parameter
Sym.
Device Min.
Typ.
Max.
Units
Test Conditions
Fig.
Note
High Level
IOH* 4.5
50
µA
VCC = 3.3 V, VO = 3.3 V,
1
1
Output Current IF = 250 µA
Input Threshold
ITH 3.0
5.0
mA
VCC = 3.3 V, VO = 0.6 V,
2
Current IOL (Sinking) = 13 mA
Low Level
VOL*
0.35
0.6
V
VCC = 3.3 V,
3
Output Voltage IF = 5 mA,
IOL (Sinking) = 13 mA
High Level
ICCH
Single 4.7
7.0
mA
IF = 0 mA
Dual
6.9
10.0
V
Supply Current
CC = 3.3 V
Low Level
ICCL
Single
7.0
10.0
mA
IF = 10 mA
Dual
8.7
15.0
VCC = 3.3 V
Supply Current
Input Forward
VF
1.4
1.5
1.75*
V
TA = 25˚C, IF = 10 mA
5
1
Voltage
Input Reverse
BVR* 5V
IR = 10 µA
1
Breakdown
Voltage
Input Diode
∆VF/–1.6mV/˚C IF = 10 mA
1
Temperature
∆TA
Coefficient
Input
CIN
60
pF
f = 1 MHz, VF = 0 V
1
Capacitance
Electrical Specifications (DC)
Over recommended operating conditions (TA=-40°C to +85°C, 4.5V ≤ VDD ≤ 5.5V) unless otherwise specified.
All typicals at VCC = 5 V, TA = 25 °C.
Parameter
Symbol
Typ.*
Max.
Units
Test Conditions
Fig.
Note
High Level Output
Current
IOH
5.5
100
mA
VCC = 5.5 V, VO = 5.5 V,
IFL = 250 mA
1
1
Input Threshold
Current
ITH
2.0
5.0
mA
VCC = 5.5 V, VO = 0.6 V,
IOL > 13 mA
2
Low Level Output
Voltage
VOL
0.35
0.6
V
VCC = 5.5 V, IF = 5 mA,
IOL(Sinking) = 13 mA
3
High Level Supply
Current
ICCH
Single
7.0
10.0
mA
VCC = 5.5 V, IF = 0 mA
Dual
10.0
15.0
mA
VCC = 5.5 V, IF = 0 mA
Low Level Supply
Current
ICCL
Single
9.0
13.0
mA
VCC = 5.5 V, IF = 10 mA
13.0
21.0
mA
VCC = 5.5 V, IF = 10 mA
Input Forward
Voltage
VF
1.5
1.75
V
TA = 25 °C, IF = 10 mA
Input Reverse
Breakdown Voltage
BVR
V
IR = 10 mA
1
Input Diode
Temperature
Coefficient
ΔVF/ΔTA
-1.6
mV/°C
IF = 10 mA
1
Input Capacitance
CIN
60
pF
f = 1 MHz, VF = 0 V
1
Min.
Dual
1.4
1.3
*All Typical at TA=25C, Vcc=5V
6
Device
5
1
1.8
5
Switching Specifications
Over Recommended Temperature (TA = –40˚C to +85˚C), VCC = 3.3 V, IF = 7.5 mA unless otherwise specified.
All Typicals at TA = 25˚C, VCC = 3.3 V.
Parameter
Sym.
Min.
Typ.
Max.
Units
Propagation Delay
tPLH90
ns
Time to High Output
Level
Propagation Delay
tPHL75
Time to Low Output
Level
Test Conditions
Fig.
Note
RL = 350 Ω
CL = 15 pF
6, 7, 8
1, 6
ns
1, 7
Pulse Width
|tPHL – tPLH|25
ns
Distortion
8
9
Propagation Delay
Skew
tPSK40
ns
8, 9
Output Rise Time
(10-90%)
tr
45
ns 1
Output Fall Time
(90-10%)
tf
20
ns 1
Switching Specifications (AC)
Over recommended operating conditions TA = -40°C to 85°C, VCC = 5 V, IF = 7.5 mA unless otherwise specified.
All typicals at VCC = 5 V, TA = 25 °C.
Parameter
Symbol
Min.
Typ.
Max.
Units
Test Conditions
Fig.
Note
Propagation Delay
Time to High
Output Level
tPLH
20
48
75
ns
TA = 25°C,
RL = 350W,
CL = 15 pF
6,7,8
1,6
100
ns
RL = 350W,
CL = 15 pF
75
ns
TA = 25°C
RL = 350W,
CL = 15 pF
100
ns
RL = 350W,
CL = 15 pF
35
ns
RL = 350 W,
CL = 15 pF
40
ns
RL = 350W,
CL = 15 pF
8,9
Propagation Delay
Time to Low
Output Level
tPHL
25
50
Pulse Width
Distortion
|tPHL - tPLH|
Propagation Delay
Skew
tpsk
Output Rise Time
(10%-90%)
tr
24
ns
RL = 350W,
CL = 15 pF
1
Output Fall Time
(10%-90%)
tf
10
ns
RL = 350W,
CL = 15 pF
1
7
3.5
1,7
8
9
Parameter
Sym.
Device
Min.
Typ.
Units
Test Conditions
Fig.
Note
Output High
Level Common
Mode Transient
Immunity
|CMH|
ACPL-W60L
ACPL-K63L
15
25
kV/ms
VCC = 3.3 V, IF = 0 mA,
VO(MIN) = 2 V,
RL = 350 W,
TA = 25°C,
VCM = 1000 V and VCM = 10 V
9
10, 12
Output Low
Level Common
Mode Transient
Immunity
|CML|
ACPL-W60L
ACPL-K63L
15
25
kV/ms
VCC = 3.3 V, IF = 7.5 mA,
VO(MAX) = 0.8 V,
RL = 350 W,
TA = 25°C,
VCM = 1000 V and VCM = 10 V
9
10, 12
Output High
Level Common
Mode Transient
Immunity
|CMH|
ACPL-W60L
ACPL-K63L
10
15
kV/ms
VCC = 5 V, IF = 0 mA,
VO(MIN) = 2 V,
RL = 350 W,
TA = 25°C,
VCM = 1000 V
9
10, 12
Output Low
Level Common
Mode Transient
Immunity
|CML|
ACPL-W60L
ACPL-K63L
10
15
kV/ms
VCC = 5 V, IF = 7.5 mA,
VO(MAX) = 0.8 V,
RL = 350 W,
TA = 25°C,
VCM = 1000 V
9
11, 12
8
Package Characteristics
All Typicals at TA = 25˚C.
Parameter
Sym.
Package
Min.
Typ.
Max
Units
Test Conditions
Fig.
Note
Input-Output
II-O*
Single1
45% RH, t = 5 s,
13, 14
µA
Insulation VI-O = 3 kV DC, TA = 25 °C
Input-Output
VISO
Single,
5000
Vrms
RH ≤ 50%, t = 1 min,
13, 14
Momentary Dual Channel TA = 25 °C
Withstand
Voltage*
Input-Output
RI-O
Single, 1012
VI-O =500 Vdc
1, 13, 15
Ω
Resistance
Dual Channel
Input-Output
CI-O
Single,
0.5
pF
f = 1 MHz, TA = 25 °C
1, 13, 15
Capacitance
Dual Channel
Input-Input
II-I
Dual Channel
0.005
RH ≤ 45%, t = 5 s,
16
µA
Insulation VI-I = 500 V
Leakage
Current
Resistance
RI-I
Dual Channel
1011
Ω16
(Input-Input)
Capacitance
CI-I
Dual Channel
0.25
pG
f = 1 MHz
16
(Input-Input)
*The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-5 Insulation Characteristics Table (if applicable), your equipment
level safety specification or Avago Application Note 1074 entitled "Optocoupler Input-Output Endurance Voltage."
Notes:
1. Each channel.
2 Peaking circuits may produce transient input currents up to 50 mA, 50 ns maximum pulse width, provided average current does not exceed
20 mA.
3. Peaking circuits may produce transient input currents up to 50 mA, 50 ns maximum pulse width, provided average current does not exceed
15 mA.
4. Derate linearly above +80˚C free-air temperature at a rate of 2.7 mW/˚C.
5. Bypassing of the power supply line is required, with a 0.1 µF ceramic disc capacitor adjacent to each optocoupler as illustrated in Figure 11.
Total lead length between both ends of the capacitor and the isolator pins should not exceed 20 mm.
6. The tPLH propagation delay is measured from the 3.75 mA point on the falling edge of the input pulse to the 1.5 V point on the rising edge
of the output pulse.
7. The tPHL propagation delay is measured from the 3.75 mA point on the rising edge of the input pulse to the 1.5 V point on the falling edge
of the output pulse.
8. tPSK is equal to the worst case difference in tPHL and/or tPLH that will be seen between units at any given temperature and specified test conditions.
9. See test circuit for measurement details.
10. CMH is the maximum tolerable rate of rise on the common mode voltage to assure that the output will remain in a high logic state
(i.e., Vo > 2.0 V).
11. CML is the maximum tolerable rate of fall of the common mode voltage to assure that the output will remain in a low logic state
(i.e., Vo < 0.8 V).
12. For sinusoidal voltages, (|dVCM | / dt)max = πfCMVCM (p-p).
13. Single channel device is considered a two-terminal part when pins 1, 2, 3 are shorted together, and pins 4, 5, 6 shorted together separately.
Dual channel device is considered a two-terminal part when pins 1, 2, 3, 4 are shorted together, and pins 5, 6, 7, 8 are shorted together
separately.
14. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 6000 V rms for one second (leakage
detection current limit, II-O ≤ 5 µA). This test is performed before the 100% production test for partial discharge (Method b) shown in the IEC/
EN/DIN EN 60747-5-5 Insulation Characteristics Table, if applicable.
15. Measured between the LED anode and cathode shorted together and pins 5 through 8 shorted together. For dual channel products only.
16. Measured between pins 1 and 2 shorted together, and pins 3 and 4 shorted together. For dual channel products only.
9
15
VCC = 3.3 V
VO = 3.3 V
IF = 250 µA
10
5
0
-60 -40
-20
0
20
60
40
80 100
I OH - HIGH LEVEL OUTPUT CURRENT - µA
IOH – HIGH LEVEL OUTPUT CURRENT – µA
15
V CC = 5.5 V
V O = 5.5 V
I F = 250 µA
10
5
0
-60 -40
-20
0
20
40
60
80 100
T A - TEMPERATURE - °C
TA – TEMPERATURE – C
12
10
6
VCC = 3.3 V
VO = 0.6 V
ITH – INPUT THRESHOLD CURRENT – mA
ITH – INPUT THRESHOLD CURRENT – mA
Figure 1. Typical high level output current vs. temperature.
8
RL = 350 KΩ
6
RL = 1 KΩ
4
2
RL = 4 KΩ
0
-60 -40 -20
0
20
40
60
5
VCC = 5.0 V
VO = 0.6 V
4
3
RL = 350 Ω
RL = 1 kΩ
2
1
0
-60 -40
80 100
TA – TEMPERATURE – C
RL = 4 kΩ
-20
0
20
40
60
80
100
TA – TEMPERATURE – °C
Figure 2. Typical input threshold current vs. temperature.
HCPL-260L fig 3
0.5
VCC = 3.3 V
IF = 5.0 mA
V OL - LOW LEVEL OUTPUT VOLTAGE - V
VOL – LOW LEVEL OUTPUT VOLTAGE – V
0.8
0.7
0.6
0.5
0.4
IO = 13 mA
0.3
0.2
0.1
0
-60 -40
-20
0
20
40
60
80
100
0.4
I O = 12.8 mA
0.3
0.2
0.1
-60 -40
TA – TEMPERATURE – °C
Figure 3. Typical low level output voltage vs. temperature.
10
V CC = 5.5 V
I F = 5.0 mA
-20
0
20
40
60
T A - TEMPERATURE - °C
80
100
60
50
IF = 5.0 mA
40
20
-60 -40
-20
20
0
40
80
TA = 25 °C
60
40
I F = 5.0 mA
20
0
-60 -40
100
80
60
1000
V CC = 5.0 V
V OL = 0.6 V
IF – FORWARD CURRENT – mA
VCC = 3.3 V
VOL = 0.6 V
I OL - LOW LEVEL OUTPUT CURRENT - mA
IOL – LOW LEVEL OUTPUT CURRENT – mA
70
-20
0
40
20
60
PULSE GEN.
ZO = 50 Ω
tf = tr = 5 ns
VCC 6
0.1 µF
BYPASS
INPUT
MONITORING
NODE
RL
5
2
*CL
3
GND
2
7
3
6
4
5
IF = 7.50 mA
IF = 3.75 mA
tPLH
1.5 V
t P - PROPAGATION DELAY - ns
tP – PROPAGATION DELAY – ns
100
tPLH , RL = 350 Ω
60
tPHL , RL = 350 Ω
0
-60
-40
-20
0
20
40
60
80
100
TA – TEMPERATURE – C
Figure7. Typical propagation delay vs. temperature
11
1.4
80
60
V CC = 5.0 V
I F = 7.5 mA
t PHL , R L = 350Ω
1 kΩ
40
20
0
-60
t PLH , R L = 350Ω
-40
-20
0
20
40
60
T A - TEMPERATURE - °C
0.1 µF
BYPASS
CL*
Figure 6. Test circuit for tPHL and tPLH
VCC = 3.3 V
IF = 7.5 mA
1.3
1.5
1.6
3.3 V / 5 V
VCC 8
RM
OUTPUT
VO
30
1.2
RM
4
tPHL
90
0.01
RL
INPUT
MONITORING
NODE
OUTPUT VO
MONITORING
NODE
INPUT
IF
120
0.1
1
*CL IS APPROXIMATELY 15 pF WHICH INCLUDES
PROBE AND STRAY WIRING CAPACITANCE.
150
1.0
DUAL CHANNEL
IF
3.3 V / 5 V
1
VF
–
10
Figure 5. Typical input diode forward characteristic.
SINGLE CHANNEL
PULSE GEN.
ZO = 50 Ω
t f = t r = 5 ns
IF
VF – FORWARD VOLTAGE – V
Figure 4. Typical low level output current vs. temperature.
IF
+
0.001
1.1
80 100
T A - TEMPERATURE - °C
TA – TEMPERATURE – °C
100
80
100
GND
OUTPUT VO
MONITORING
NODE
40
VCC = 3.3 V
IF = 7.5 mA
40
PWD - PULSE WIDTH DISTORTION - ns
PWD – PULSE WIDTH DISTORTION – ns
50
30
RL = 350 Ω
20
10
0
-60
-40
-20
20
0
40
60
80
30
20
R L = 350 kΩ
10
0
-10
100
V CC = 5.0 V
I F = 7.5 mA
-60
-40
TA – TEMPERATURE – C
-20
0
20
40
80
60
100
T A - TEMPERATURE - °C
Figure 8. Typical pulse width distortion vs. temperature
IF
IF
SINGLE CHANNEL
B
A
VFF
1
VCC 6
5
2
3
GND
DUAL CHANNEL
B
0.1 µF
BYPASS
1
A
+3.3 V / 5 V
VCC 8
RL
2
7
3
6
VFF
OUTPUT VO
MONITORING
NODE
4
4
GND
VCM
VCM
–
+
PULSE
GENERATOR
ZO = 50 Ω
VCM
VO
VO
–
+
PULSE
GENERATOR
ZO = 50 Ω
VCM (PEAK)
0V
5V
SWITCH AT A: IF = 0 mA
VO (MIN.)
SWITCH AT B: IF = 7.5 mA
VO (MAX.)
0.5 V
CMH
CML
Figure 9. Test circuit for common mode transient immunity and typical waveforms
For product information and a complete list of distributors, please go to our web site:
+3.3 V / 5 V
RL
www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries.
Data subject to change. Copyright © 2005-2013 Avago Technologies. All rights reserved. Obsoletes AV01-0206EN
AV02-0890EN - April 4, 2013
5
0.1 µF
BYPASS
OUTPUT VO
MONITORING
NODE