DATASHEET 16-Bit Long-Reach Video Automotive Grade SERDES ISL76322 Features The ISL76322 is a serializer/deserializer of LVCMOS parallel video data. The video data presented to the serializer on the parallel LVCMOS bus is serialized into a high-speed differential signal. This differential signal is converted back to parallel video at the remote end by the deserializer. The fully featured register set is programmed through the industry standard I2C. • 16-bit RGB Transport Over a Single Differential Pair Related Literature • DC-balanced with Industry Standard 8b/10b Line Code Allows AC-coupling, Providing Immunity Against Ground Shifts • 16 Programmable Settings Each for Transmitter Amplitude Boost and Pre-emphasis and Receiver Equalization, Allow for Longer Cable Lengths and Higher Data Rates • See FN6827, ISL34341 Data Sheet “WSVGA 24-Bit Long-Reach Video SERDES with Bi-directional Side-Channel” • 6MHz to 50MHz Pixel Clock Rates • AEC-Q100 Qualified Component • Hot-plugging with Automatic Resynchronization Every HSYNC • Selectable Clock Edge for Parallel Data Output • Slew Rate Control and Spread Spectrum Capability on Outputs Reduce the Potential for EMI • Same Device for Serializer and Deserializer Simplifies Inventory Applications • Video Entertainment Systems • Remote Cameras 27nF 27nF VDD_CR VDD_CDR VDD_P VDD_IO ISL76322 SERION DESERIALIZER VIDEO TARGET DE VIDEO_TX I2CA1 I2CA0 TEST_EN 3.16k GND_CR GND_AN GND_P GND_TX GND_CDR GND_IO VSYNC HSYNC PCLK_OUT PCLK_IN REF_RES REF_CLK VIDEO_TX 16 RGB SERIOP SERION I2CA1 I2CA0 TEST_EN REF_RES 3.16k 1.8V VDD_IO RSTB/PDB 27nF VDD_AN VDD_TX 27nF SERIOP ISL76322 SERIALIZER GND_CR GND_AN GND_P GND_TX GND_CDR GND_IO VSYNC HSYNC DE PCLK_IN RSTB/PDB VDD_CR VDD_CDR RGB VIDEO SOURCE 3.3V 1.8V VDD_IO VDD_P VDD_IO VDD_TX 16 VDD_AN 3.3V VDD_IO FIGURE 1. TYPICAL APPLICATION May 6, 2015 FN7611.3 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas LLC 2011, 2013, 2015. All Rights Reserved Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries. All other trademarks mentioned are the property of their respective owners. ISL76322 Block Diagram SCL I2C SDA VCM GENERATOR RAM SERIOP PREEMPHASIS TX 3 V/H/DE TDM 8b/10b RGB SERION MUX DEMUX 16 RX EQ VIDEO_TX (HI) CDR PCLK_IN (REF_CLK WHEN VIDEO_TX IS LO) x20 PCLK_ OUT x20 Submit Document Feedback 2 May 6, 2015 FN7611.3 ISL76322 Pin Configuration GND_IO RGBA7 RGBA6 RGBA5 RGBA4 RGBA3 RGBA2 RGBA1 RGBA0 PCLK_OUT VDD_IO GND_IO ISL76322 (48 LD QFN) TOP VIEW 48 47 46 45 44 43 42 41 40 39 38 37 VDD_IO 1 36 VDD_CDR RGBC0 2 35 GND_CDR RGBC1 3 34 VDD_TX RGBC2 4 33 SERIOP RGBC3 5 32 SERION RGBC4 6 31 GND_TX PAD RGBC5 7 30 VDD_AN RGBC6 8 29 GND_AN RGBC7 9 28 REF_RES STATUS 10 27 MASTER 16 17 18 19 20 21 VSYNC VHSYNCPOL VIDEO_TX PCLK_IN GND_P 22 23 24 SDA 15 SCL 14 VDD_P 13 HSYNC 25 I2CA1 DATAEN RSTB/PDB 12 VDD_CR 26 I2CA0 GND_CR TEST_EN 11 Pin Descriptions DESCRIPTION PIN NUMBER PIN NAME 47, 46 45, 44 43, 42 41, 40 9, 8 7, 6 5, 4 3, 2 RGBA7, RGBA6 RGBA5, RGBA4 RGBA3, RGBA2 RGBA1, RGBA0 RGBC7, RGBC6 RGBC5, RGBC4 RGBC3, RGBC2 RGBC1, RGBC0 Parallel video data LVCMOS inputs with Hysteresis Parallel video data LVCMOS outputs 16 HSYNC Horizontal (line) Sync LVCMOS input with Hysteresis Horizontal (line) Sync LVCMOS output 17 VSYNC Vertical (frame) Sync LVCMOS input with Hysteresis Vertical (frame) Sync LVCMOS output 15 DATAEN Video Data Enable LVCMOS input with Hysteresis Video Data Enable LVCMOS output 20 PCLK_IN Pixel clock LVCMOS input PLL reference clock LVCMOS input 39 PCLK_OUT Default; not used Recovered clock LVCMOS output 33, 32 SERIOP, SERION High-speed differential serial I/O High speed differential serial I/O Submit Document Feedback 3 SERIALIZER DESERIALIZER May 6, 2015 FN7611.3 ISL76322 Pin Descriptions (Continued) DESCRIPTION PIN NUMBER PIN NAME SERIALIZER 18 VHSYNCPOL 19 VIDEO_TX 24, 23 SDA, SCL (Note 1) I2C Interface Pins (I2C DATA, I2C CLK), weak internal pullup 25, 26 I2CA[1:0] (Note 1) I2C Device Address 27 MASTER 12 RSTB/PDB 10 STATUS 28 REF_RES 21 GND_P (Note 2) PLL Ground 37, 48 GND_IO (Note 2) Digital (Parallel and Control) Ground 35 GND_CDR (Note 2) 31 GND_TX (Note 2) Analog (Serial) Output Ground 29 GND_AN (Note 2) Analog Bias Ground 13 GND_CR (Note 2) Core Logic Ground 14 VDD_CR Core Logic VDD 34 VDD_TX Analog (Serial) Output VDD 30 VDD_AN Analog Bias VDD 36 VDD_CDR 1, 38 VDD_IO (Note 1) 22 VDD_P 11 TEST_EN Exposed Pad PAD DESERIALIZER CMOS input for HSYNC and VSYNC Polarity 1: HSYNC & VSYNC active low 0: HSYNC & VSYNC active high CMOS input for video flow direction 1: Video serializer 0: Video deserializer I2C Master Mode 1: Master 0: Slave CMOS input for Reset and Power-down. For normal operation, this pin should be driven high. When this pin is taken low, the device will be reset. If this pin stays low, the device will be in PD mode. CMOS output for Receiver Status: 1: Valid 8b/10b data received 0: No valid data detected Note: serializer and deserializer switch roles during side-channel reverse traffic Analog bias setting resistor connection; use 3.16k ±1% to ground Analog (Serial) Data Recovery Ground Analog (Serial) Data Recovery VDD Digital (Parallel and Control) VDD PLL VDD Must be connected to ground Must be connected to ground, not an electrical connection NOTES: 1. Pins with the same name are internally connected together. However, this connection must NOT be used for connecting together external components or features. 2. The various differently-named Ground pins are internally weakly connected. They must be tied together externally. The different names are provided to assist in minimizing the current loops involved in bypassing the associated supply VDD pins. In particular, for ESD testing, they should be considered a common connection. Submit Document Feedback 4 May 6, 2015 FN7611.3 ISL76322 Ordering Information PART NUMBER (Notes 3, 4, 5) ISL76322ARZ PART MARKING ISL76322 ARZ TEMP. RANGE (°C) -40 to +105 PACKAGE (RoHS Compliant) 48 Ld QFN PKG. DWG. # L48.7x7C NOTES: 3. Add “-T*” suffix for tape and reel. Please refer to TB347 for details on reel specifications. 4. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pbfree products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 5. For Moisture Sensitivity Level (MSL), please see device information page for ISL76322. For more information on MSL please see techbrief TB363. Submit Document Feedback 5 May 6, 2015 FN7611.3 ISL76322 Absolute Maximum Ratings Thermal Information Supply Voltage VDD_P to GND_P, VDD_TX to GND_TX, VDD_IO to GND_IO . . . -0.5V to 4.6V VDD_CDR to GND_CDR, VDD_CR to GND_CR. . . . . . . . . . . -0.5V to 2.5V Between any pair of GND_P, GND_TX, GND_IO, GND_CDR, GND_CR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-0.1V to 0.1V 3.3V Tolerant LVTTL/LVCMOS Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to VDD_IO +0.3V Differential Input Voltage . . . . . . . . . . . . . . . . . . . . .-0.3V to VDD_IO + 0.3V Differential Output Current . . . . . . . . . . . . . . . . . . . . Short Circuit Protected LVTTL/LVCMOS Outputs. . . . . . . . . . . . . . . . . . . . . . . Short Circuit Protected ESD Rating Human Body Model (Tested per JESD22-A114E) All pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4kV SERIOP/N (All VDD Connected, all GND Connected) . . . . . . . . . . . . . . . . . . . . 8kV Machine Model (Tested per JESD-A115-A) . . . . . . . . . . . . . . . . . . . . 200V Charge Device Model (Tested per AEC-Q100-011-B) . . . . . . . . . . . . . 2000V Latch-up (Tested per JESD-78B; Class2, Level A) . . . . . . . . . . . . . . . 100mA Thermal Resistance (Typical) JA JC (°C/W) QFN Package (Notes 6, 7) . . . . . . . . . . . . . . 32 3.7 Maximum Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327mW Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . .+125°C Maximum Storage Temperature Range . . . . . . . . . . . . . .-65°C to +150°C Pb-free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see TB493 Recommended Operating Conditions Operating Temperature Range . . . . . . . . . . . . . . . . . . . . . .-40°C to +105°C CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTES: 6. JA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech Brief TB379. 7. For JC, the “case temp” location is the center of the exposed metal pad on the package underside. Electrical Specifications Unless otherwise indicated, all data is for: VDD_CDR = VDD_CR = 1.8V, VDD_IO = 3.3V, VDD_TX = VDD_P = VDD_AN = 3.3V, TA = +25°C, Ref_Res = 3.16k, High-speed AC-coupling capacitor = 27nF. Boldface limits apply over the operating temperature range, -40°C to +105°C. MIN (Note 10) TYP MAX (Note 10) UNIT VDD_CDR, VDD_CR 1.7 1.8 1.9 V VDD_TX, VDD_P, VDD_AN, VDD_IO 3.0 3.3 3.6 V PARAMETER SYMBOL TEST CONDITIONS POWER SUPPLY VOLTAGE SERIALIZER POWER SUPPLY CURRENTS Total 1.8V Supply Current PCLK_IN = 45MHz 62 80 mA Total 3.3V Supply Current (Note 8) 40 52 mA Total 1.8V Supply Current PCLK_IN = 45MHz 66 76 mA Total 3.3V Supply Current (Note 8) 50 63 mA RSTB = GND 10 mA 0.5 mA DESERIALIZER POWER SUPPLY CURRENTS POWER-DOWN SUPPLY CURRENT Total 1.8V Power-Down Supply Current Total 3.3V Power-Down Supply Current PARALLEL INTERFACE High Level Input Voltage VIH Low Level Input Voltage VIL Input Leakage Current IIN High Level Output Voltage VOH IOH = -4.0mA, VDD_IO = 3.0V Low Level Output Voltage VOL IOL = 4.0mA, VDD_IO = 3.6V Output Short Circuit Current IOSC Submit Document Feedback 6 2.0 -1 V ±0.01 0.8 V 1 µA 2.6 V 0.4 V 35 mA May 6, 2015 FN7611.3 ISL76322 Electrical Specifications Unless otherwise indicated, all data is for: VDD_CDR = VDD_CR = 1.8V, VDD_IO = 3.3V, VDD_TX = VDD_P = VDD_AN = 3.3V, TA = +25°C, Ref_Res = 3.16k, High-speed AC-coupling capacitor = 27nF. Boldface limits apply over the operating temperature range, -40°C to +105°C. (Continued) PARAMETER SYMBOL Output Rise and Fall Times tOR/tOF TEST CONDITIONS MIN (Note 10) TYP MAX (Note 10) UNIT Slew rate control set to min CL = 8pF 1 ns Slew rate control set to max, CL = 8pF 4 ns SERIALIZER PARALLEL INTERFACE PCLK_IN Frequency fIN 6 PCLK_IN Duty Cycle tIDC 40 50 50 MHz 60 % Parallel Input Setup Time tIS 3.5 ns Parallel Input Hold Time tIH 1.0 ns PCLK_OUT Frequency fOUT 6 PCLK_OUT Duty Cycle tODC DESERIALIZER PARALLEL INTERFACE PCLK_OUT Period Jitter (rms) PCLK_OUT Spread Width tOJ Clock randomizer off tOSPRD Clock randomizer on 50 % 0.5 %tPCLK ±20 PCLK_OUT to Parallel Data Outputs (includes Sync and DE pins) tDV Relative to PCLK_OUT, (Note 9) -1.0 Deserializer Output Latency tCPD Inherent in the design 4 MHz 50 9 %tPCLK 5.5 ns 14 PCLK DESERIALIZER REFERENCE CLOCK (REF_CLK IS FED INTO PCLK_IN) REF_CLK Lock Time tPLL REF_CLK to PCLK_OUT Maximum Frequency Offset PCLK_OUT is the recovered clock 1500 TXCN = 0x00 650 100 µs 5000 ppm HIGH-SPEED TRANSMITTER HS Differential Output Voltage, Transition Bit VODTR VODNTR 900 mVP-P 900 mVP-P TXCN = 0xF0 1100 mVP-P TXCN = 0xFF HS Differential Output Voltage, Non-Transition Bit 800 TXCN = 0x0F TXCN = 0x00 1300 650 800 mVP-P 900 mVP-P TXCN = 0x0F 900 mVP-P TXCN = 0xF0 430 mVP-P TXCN = 0xFF 600 mVP-P V HS Generated Output Common Mode Voltage VOCM 2.35 HS Common Mode Serializer-Deserializer Voltage Difference VCM 10 20 mV HS Differential Output Impedance ROUT 80 100 120 Ω HS Output Latency tLPD Inherent in the design 4 7 10 PCLK HS Output Rise and Fall Times tR/tF 20% to 80% HS Differential Skew tSKEW 150 ps <10 ps HS Output Random Jitter tRJ PCLK_IN = 45MHz 6 psrms HS Output Deterministic Jitter tDJ PCLK_IN = 45MHz 25 psP-P Submit Document Feedback 7 May 6, 2015 FN7611.3 ISL76322 Electrical Specifications Unless otherwise indicated, all data is for: VDD_CDR = VDD_CR = 1.8V, VDD_IO = 3.3V, VDD_TX = VDD_P = VDD_AN = 3.3V, TA = +25°C, Ref_Res = 3.16k, High-speed AC-coupling capacitor = 27nF. Boldface limits apply over the operating temperature range, -40°C to +105°C. (Continued) PARAMETER SYMBOL TEST CONDITIONS MIN (Note 10) TYP MAX (Note 10) UNIT HIGH SPEED RECEIVER HS Differential Input Voltage VID HS Generated Input Common Mode Voltage VICM HS Differential Input Impedance RIN 75 mVP-P 2.32 80 HS Maximum Jitter Tolerance 100 V 120 0.50 Ω UIP-P I2C I2C Clock Rate (on SCL) fI2C 100 400 kHz I2C Clock Pulse Width (HI or LO) 1.3 I2C Clock Low to Data Out Valid 0 I2C Start/Stop Setup/Hold Time 0.6 µs I2C Data in Setup Time 100 ns I2C Data in Hold Time 100 ns I2C Data out Hold Time 100 ms µs 1 µs NOTES: 8. IDDIO is nominally 50µA and not included in this total as it is dominated by the loading of the parallel pins. 9. This parameter is the output data skew from the invalid edge of PCLK_OUT. The setup and hold time provided to a system is dependent on the PCLK frequency and is calculated as follows: 0.5 * fIN - tDV.. 10. Compliance to datasheet limits is assured by one or more methods: production test, characterization and/or design. Submit Document Feedback 8 May 6, 2015 FN7611.3 ISL76322 Timing Diagrams BIT BOUNDARY BIT BOUNDARY BIT BOUNDARY TXP VOLTAGE Tx SETTING 0x0F 0x00 VCM 0xFF 0xF0 TXN VOD TRANSITION BIT VOD NON-TRANSITION BIT FIGURE 2. VOD vs TX SETTING SERIALIZER MODE 1/FIN tIDC PCLK_IN (RISING EDGE DEFAULT) tIS RGBA[7:0], RGBC[7:0] tIH VALID DATA VALID DATA DATA IGNORED DATA IGNORED tIS VALID DATA tIH HSYNC OR VSYNC (HVSYNCPOL = ‘0’) DATAEN (ACTIVE ‘1’ DEFAULT) FIGURE 3. PARALLEL VIDEO INPUT TIMING Submit Document Feedback 9 May 6, 2015 FN7611.3 ISL76322 DESERIALIZER MODE 1/FOUT tODC tOR PCLK_OUT (RISING EDGE DEFAULT) tOF tDV RGBA[7:0], RGBC[7:0] VALID DATA VALID DATA PREVIOUS DATA HELD VALID DATA tDV HSYNC OR VSYNC ( HVSYNCPOL = ‘0’) DATAEN (ACTIVE ‘1’ DEFAULT) FIGURE 4. PARALLEL VIDEO OUTPUT TIMING Applications Detailed Description and Operation A pair of ISL76322 SERDES transports 16-bit parallel video for the ISL76322 along with auxiliary data over a single 100Ω differential cable either to a display or from a camera. Auxiliary data is transferred in both directions every video frame. This feature can be used for remote configuration and telemetry. The benefits include lower EMI, lower costs, greater reliability and space savings. The same device can be configured to be either a serializer or deserializer by setting one pin (VIDEO_TX), simplifying inventory. RGBA/C, VSYNC, HSYNC, and DATAEN pins are inputs in serializer mode and outputs in deserializer mode. The video data presented to the serializer on the parallel LVCMOS bus is serialized into a high-speed differential signal. This differential signal is converted back to parallel video at the remote end by the deserializer. The Side Channel data (auxiliary data) is transferred between the SERDES pair during the first two lines of the vertical video blanking interval. impedance, as well as the pre-emphasis and equalization settings. Functioning links of 25 meters are often possible at the maximum frequency. SERIOP and SERION pins incorporate internal differential termination of the serial signal lines. SERIO Pin AC-Coupling AC-coupling minimizes the effects of DC common mode voltage difference and local power supply variations between two SERDES. The serializer outputs DC balanced 8b/10b line code, which allows AC-coupling. The AC-coupling capacitor on SERIO pins must be 27nF on the serializer board and 27nF on the deserializer board. The value of the AC-coupling capacitor is very critical since a value too small will attenuate the high-speed signal at low clock rate. A value too big will slow down the turn around time for the side-channel. It is an advantage to have the pair of capacitors as closely matched as possible. Receiver Reference Clock (REF_CLK) When the side-channel is enabled, which is the default, there will be a number of PCLK cycles uncertainty from frame-to-frame. This should not cause sync problems with most displays as this occurs during the vertical front porch of the blanking period. When properly configured, the SERDES link supports end-to-end transport with fewer than one error in 1010 bits. The reference clock (REF_CLK) for the PLL is fed into PCLK_IN pin. REF_CLK is used to recover the clock from the high-speed serial stream. REF_CLK is very sensitive to any instability. The following conditions must be met at all times after power is applied to the deserializer, or else the deserializer may need a manual reset: Differential Signals and Termination • VDD must be applied and stable The ISL76322 serializes the 16-bit parallel data plus 3 sync signals at 20x the PCLK_IN frequency. The extra 2 bits per word come from the 8b/10b encoding scheme which helps create the highest quality serial link. • REF_CLK frequency must be within the limits specified The high bit rate of the differential serial data requires special care in the layout of traces on PCBs, in the choice and assembly of connectors, and in the cables themselves. Power Supply Sequencing PCB traces need to be adjacent, matched in length and drawn to result in a differential 100Ω controlled impedance. For best EMI performance, the cable should be low loss and have a differential 100Ω impedance. The maximum cable length for a functioning link is dependent on the PCLK_IN frequency, the cable loss and Submit Document Feedback 10 • REF_CLK amplitude must be stable A simple 3.3V CMOS crystal oscillator can be used for REF_CLK The 3.3V supply must be higher than the 1.8V supply at all times, including during power-up and power-down. To meet this requirement, the 3.3V supply must be powered up before the 1.8V supply. For the deserializer, REF_CLK must not be applied before the device is fully powered up. Applying REF_CLK before power-up May 6, 2015 FN7611.3 ISL76322 may require the deserializer to be manually reset. A 10ms delay after the 1.8V supply is powered up guarantees normal operation. should be arranged to emulate this arrangement (at least for the smaller value (high frequency) capacitors), as much as possible. Power Supply Bypassing and Layout 120Ω The serializer and deserializer functions rely on the stable functioning of PLLs locked to local reference sources or locked to an incoming signal. It is important that the various supplies (VDD_P, VDD_AN, VDD_CDR, VDD_TX) be well bypassed over a wide range of frequencies, from below the typical loop bandwidth of the PLL to approaching the signal bit rate of the serial data. A combination of different values of capacitors from 1000pF to 5µF or more with low ESR characteristics is generally required. Submit Document Feedback 11 10µF 0.1µF 10µF 0.1µF 10µF 0.1µF 10µF 0.1µF 10µF 0.1µF 120Ω 120Ω 120Ω 120Ω A set of arrangements of this type is shown in Figure 5, where each supply is bypassed with a ferrite-bead-based choke, and a range of capacitors. A “choke” is preferable to an “inductor” in this application, since a high-Q inductor will be likely to cause one or more resonances with the shunt capacitors, potentially causing problems at or near those frequencies, while a “lossy” choke will reflect a high impedance over a wide frequency range. Capacitors of 0.1µF offer low impedance in the 10MHz to 20MHz region, and 1000pF capacitors in the 100MHz to 200MHz region. In general, one of the lower value capacitors should be used at each supply pin on the IC. Figure 5 shows the grounding of the various capacitors to the pin corresponding to the supply pin. Although all the ground supplies are tied together, the PCB layout 0.1µF 120Ω The parallel LVCMOS VDD_IO supply is inherently less sensitive, but since the RGB and SYNC/DATAEN signals can all swing on the same clock edge, the current in these pins, and the corresponding GND pins, can undergo substantial current flow changes. Once again, a combination of different values of capacitors over a wide range, with low ESR characteristics, is desirable. The higher value capacitor, in particular, needs to be chosen carefully, with special care regarding its ESR. Very good results can be obtained with multilayer ceramic capacitors (available from many suppliers) and generally in small outlines (such as the 1210 outline suggested in the schematic shown in Figure 5), which provide good bypass capabilities down to a few mΩ at 1MHz to 2MHz. Other capacitor technologies may also be suitable (perhaps niobium oxide), but “classic” electrolytic capacitors frequently have ESR values of above 1Ω, that nullify any decoupling effect above the 1kHz to 10kHz frequency range. 10µF FIGURE 5. POWER SUPPLY BYPASSING I2C Interface The I2C interface allows access to internal registers used to configure the SERDES and to obtain status information. A serializer must be assigned a different address than its deserializer counterpart if the side channel is used. The upper 5 bits are permanently set to 011 11 and the lower 2 bits determined by pins as follows: 0 1 1 1 1 I2CA1 I2CA0 R/W Thus, 4 SERDES can reside on the same bus. By convention, when all address pins are tied low, the device address is referred to as 0x78. SCL and SDA are open drain to allow multiple devices to share the bus. If not used, SCL and SDA should be tied to VDD_IO. May 6, 2015 FN7611.3 ISL76322 Exposed Pad While it is not a required electrical connection, it is recommended that the exposed pad on the bottom of the package be soldered to the circuit board. This will ensure that the full power dissipation of the package can be utilized. The pad should be connected to ground and not left floating. For best thermal conductivity, 16 vias should connect the footprint for the exposed pad on the circuit board to the ground plane. This connection is not required for basic operation of the chip. COPPER PAD VIAS 16x FIGURE 6. LAYOUT FOR THE EXPOSED PAD For additional products, see www.intersil.com/en/products.html Intersil Automotive Qualified products are manufactured, assembled and tested utilizing TS16949 quality systems as noted in the quality certifications found at www.intersil.com/en/support/qualandreliability.html Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com Submit Document Feedback 12 May 6, 2015 FN7611.3 ISL76322 Revision History The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to web to make sure you have the latest Rev. DATE REVISION CHANGE May 6, 2015 FN7611.3 “Absolute Maximum Ratings” on page 6 - changed Charge Device Model from (Tested per JESD22-C101C) to (Tested per AEC-Q100-011-B) December 23, 2013 FN7611.2 Page 12 - 2nd line of the disclaimer changed from: "Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted" to: "Intersil Automotive Qualified products are manufactured, assembled and tested utilizing TS16949 quality systems as noted" March 1, 2011 FN7611.1 Removed 4th bullet from Features on page 1 which read “Bi-directional Auxiliary Data Transport without Extra Bandwidth and Over the Same Differential Pair” January 31, 2011 FN7611.0 Initial Release. About Intersil Intersil Corporation is a leading provider of innovative power management and precision analog solutions. The company's products address some of the largest markets within the industrial and infrastructure, mobile computing and high-end consumer markets. For the most updated datasheet, application notes, related documentation and related parts, please see the respective product information page found at www.intersil.com. You may report errors or suggestions for improving this datasheet by visiting www.intersil.com/ask. Reliability reports are also available from our website at www.intersil.com/support Submit Document Feedback 13 May 6, 2015 FN7611.3 ISL76322 Package Outline Drawing L48.7x7C 48 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE (PUNCH QFN) Rev 0, 1/08 7.00 EXPOSED PAD AREA A Z B X 6.75 48 48 6 PIN 1 INDEX AREA 6 PIN #1 INDEX AREA 1 6.75 7.00 REF (4X) 1 7.00 (44X 0.50) 4 0.23 0.15 (4X) (48X 0.40 ± 0.1mm) TOP VIEW 0.100 4.10 REF (4X) C A B BOTTOM VIEW 11 °±1° ALL AROUND PACKAGE OUTLINE Y 6.75 7.00 4.10 SIDE VIEW R0.200 (48x 0.20) (48x 0.60) C0.400X45°X (4X) (0 .1 25 ) O 0.450 (48x 0.23) UN D TYPICAL RECOMMENDED LAND PATTERN ) (44x 0.50) 7.00 L (A LL AR R0.200 TYP. 1 R0.200 MAX ALL AROUND 0.100 C 48 DETAIL "Z" DETAIL "X" R0.115 TYP. 0.65 0.85 NOTES: 1. 0.19~ 0.245 SEATING 0.080 C 0.025 ± 0.02 e b 0.100 C A B 0.050 C DETAIL "Y" PLANE C Dimensions are in millimeters. Dimensions in ( ) for Reference Only. 2. Dimensioning and tolerancing conform to JESD-MO220. 3. Unless otherwise specified, tolerance : Decimal ± 0.05, body tolerance ± 0.1 4. Dimension b applies to the metallized terminal and is measured between 0.18mm and 0.28mm from the terminal tip. Frame base metal thickness 0.203mm. 5. Tiebar shown (if present) is a non-functional feature. 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature. Submit Document Feedback 14 May 6, 2015 FN7611.3