TOREX XC9508_1

XC9508 Series
ETR1005_001
Synchronous Step-Down DC/DC Converter
with Built-In LDO Regulator in Series Plus Voltage Detector
■GENERAL DESCRIPTION
The XC9508 series consists of a step-down DC/DC converter and a high-speed LDO regulator connected in series with the
DC/DC converter's output. A voltage detector is also built-in. A highly efficient, low noise output is possible since the
regulator is stepped-down further from the DC/DC output.
The DC/DC converter block incorporates a P-channel driver transistor and a synchronous N-channel switching transistor.
With an external coil, diode and two capacitors, the XC9508 can deliver output currents up to 600mA at efficiencies over 90%.
The XC9508 is designed for use with small ceramic capacitors. A choice of three switching frequencies are available, 300
kHz, 600 kHz, and 1.2 MHz. Output voltage settings for the DC/DC is set-up internally in 100mV steps within the range of
1.6V to 4.0V(± 2.0%) and for the VR are set-up internally within the range of 0.9V to 4.0V (± 2.0%). For the VD, the range is
of 0.9V to 5.0V (± 2.0%). The soft start time of the series is internally set to 5ms. With the built-in U.V.L.O. (Under Voltage
Lock Out) function, the internal P-channel driver transistor is forced OFF when input voltage becomes 1.4 V or lower. The
functions of the MODE pin can be selected via the external control pin to switch the DC/DC control mode and the disable pin
to shut down the regulator block.
■APPLICATIONS
●CD-R / RW, DVD
●HDD
●PDAs, portable communication modem
●Cellular phones
●Palmtop computers
●Cameras, video recorders
■FEATURES
DC/DC Converter with Built-in LDO and VD Function
Input Voltage Range : 2.4V ~ 6.0V
Low ESR Capacitor : Ceramic capacitor compatible
VD Function
: N-channel open drain output
Small Package
: MSOP-10, USP-10
<DC/DC Converter Block>
Output Voltage Range : 1.6V ~ 4.0V (Accuracy ± 2%)
Output Current
: 600mA (for MSOP-10 package)
400mA (for USP-10 package)
Control Mothod
: PWM or PWM/PFM Selectable
Oscillation Frequency : 300kHz, 600kHz, 1.2MHz
<Regulator Block>
Regulator Input
: Serial input from DC/DC output
Output Voltage Range : 0.9V ~ 4.0V (Accuracy ± 2%)
Current Limit
: 300mA
Dropout Voltage
: 80mV @ IOUT=100mA
(VOUT=2.8V)
High Ripple Rejection : 60dB @1kHz (VOUT=2.8V)
■TYPICAL APPLICATION CIRCUIT
■TYPICAL PERFORMANCE
CHARACTERISTICS
XC9508Cxxxx
VIN=3.6V, Topr=25OC, L=4.7μH (CDRH4D28C)
CIN:4.7μF ‘(ceramic), CL1:10μF (ceramic), CL2: 4.7μF (ceramic)
MSOP-10 (TOP VIEW)
* Please refer to the typical application circuit when
external components are selected.
1/38
XC9508 Series
■PIN ASSIGNMENT
PGND 1
10 LX
CE 2
9 DCOUT
VDD 3
8 VROUT
VDOUT 4
7 MODE
VDIN 5
6 AGND
USP-10 (BOTTOM VIEW)
MSOP-10 (TOP VIEW)
*The dissipation pad for the USP-10 package
should be solder-plated in recommended
mount pattern and metal masking so as to
enhance mounting strength and heat
release. If the pad needs to be connected
to other pins, it should be connected to the
AGND pin.
■PIN CONFIGURATION
PIN NUMBER
PIN NAME
FUNCTION
1
2
3
4
5
6
7
8
PGND
CE
VDD
VDOUT
VDIN
AGND
MODE
VROUT
Power Ground
Chip Enable
Power Supply
VD Output
VD Input
Analog Ground
Mode Switch
VR Output
9
10
DCOUT
LX
DC/DC Output Sense
Switch
■PRODUCT CLASSIFICATION
●Ordering Information
XC9508①②③④⑤⑥
The input for the voltage regulator block comes from the DC/DC.
DESIGNATOR
①
②③
DESCRIPTION
Control Methods and
the VD Sense Pin
Setting Voltage &
Specifications
④
DC/DC Oscillation
Frequency
⑤
Package &
DC/DC Current limit
⑥
Device Orientation
SYMBOL
As chart below
Internal
standard
3
6
C
A
D
R
L
DESCRIPTION
:: Setting voltage and specifications of each DC/DC,
VR, and VD (Based on the internal standard)
: 300kHz
: 600kHz
: 1.2MHz
: MSOP-10, Current limiter: 1.1A (TYP.)
: USP-10, Current limiter: 0.7A (TYP.)
: Embossed Tape, standard feed
: Embossed Tape, reverse feed
●Control Methods and MODE Pin
SERIES
XC9508
①
DC/DC CONTROL METHODS
MODE PINS (H LEVEL)
A
PWM Control
VR: OFF
VR: ON
C
PWM, PFM/PWM Manual Switch
PFM / PWM Switch
PWM Control
* The XC9508A series' MODE pin switches the regulator to the stand-by mode.
When the CE mode is off, every function except for the VD function enters into the stand-by mode.
(The MODE pin does not operate independently.)
2/38
MODE PINS (L LEVEL)
XC9508
Series
■BLOCK DIAGRAM
* Diodes shown in the above circuit are protective diodes.
■ABSOLUTE MAXIMUM RATINGS
Ta = 25℃
PARAMETER
SYMBOL
RATINGS
UNIT
VDD Pin Voltage
VDD
- 0.3 ~ 6.5
V
DCOUT Pin Voltage
DCOUT
- 0.3 ~ VDD + 0.3
V
VROUT Pin Voltage
VROUT
- 0.3 ~ VDD + 0.3
V
VROUT Pin Current
IROUT
800
mA
VDOUT Pin Voltage
VDOUT
- 0.3 ~ VDD + 0.3
V
VDOUT Pin Current
IVD
50
mA
VDIN Pin Voltage
VDIN
- 0.3 ~ VDD + 0.3
V
Lx Pin Voltage
Lx
- 0.3 ~ VDD + 0.3
V
Lx Pin Current
MSOP-10
USP-10
Ilx
1300
900
mA
CE Pin Voltage
CE
- 0.3 ~ VDD + 0.3
V
MODE Pin Voltage
MODE
- 0.3 ~ VDD + 0.3
V
Power Dissipation
MSOP-10
USP-10
Pd
350 (*)
150
mW
Operating Temperature Range
Topr
- 40 ~ + 85
℃
Storage Temperature Range
Tstg
- 55 ~ + 125
℃
(*) When PC board mounted.
3/38
XC9508 Series
■ELECTRICAL CHARACTERISTICS
XC9508xxxCAx
●Common Characteristics
Topr=25℃
PARAMETER
SYMBOL
CONDITIONS
MIN.
TYP.
MAX.
UNITS
Supply Current 1
IDD1
VIN=CE=DCOUT=5.0V
-
250
310
μA
1
Supply Current 2
IDD2
VIN=CE=5.0V, DCOUT=0V
-
300
360
μA
1
Stand-by Current (*1)
ISTB
VIN=6.5V, CE=0V
Input Voltage Range
VIN
CE ‘H’ Level Voltage
CE ‘L’ Level Voltage
CE ‘H’ Level Current
ICEH
- 0.1
-
0.1
μA
1
CE ‘L’ Level Current
ICEL
- 0.1
-
0.1
μA
1
2
CIRCUIT
-
0.5
2.5
μA
1
2.4
-
6.0
V
-
VCEH
0.6
-
VDD
V
3
VCEL
VSS
-
0.25
V
3
MODE 'H' Level Voltage*XC9508A
VMH
0.6
-
VDD
V
MODE 'H' Level Voltage*XC9508C
VMH
0.6
-
VDD
V
3
MODE 'L' Level Voltage*XC9508A
VML
VSS
-
0.25
V
2
MODE 'L' Level Voltage*XC9508C
VML
VSS
-
0.25
V
3
MODE 'H' Level Current
IMH
- 0.1
-
0.1
μA
1
MODE 'L' Level Current
IML
- 0.1
-
0.1
μA
1
●DC/DC Converter (2.2V product)
Topr=25℃
PARAMETER
SYMBOL
CONDITIONS
Supply Current 1 *XC9508A
IDD_DC1
VIN=CE=DCOUT=5.0V
Supply Current 2 *XC9508A
IDD_DC2
VIN=CE=5.0V, DCOUT=0V
PFM Supply Current 1 * 9508C
IDD_PFM1
VIN=CE=DCOUT=5.0V
PFM Supply Current 2 * 9508C
IDD_PFM2
VIN=CE=5.0V, DCOUT=0V
2.156
Connected to the external components,
MIN.
MAX.
UNITS
CIRCUIT
200
280
μA
1
250
330
μA
1
250
310
μA
1
300
360
μA
1
2.200
2.244
V
3
1.02
1.20
1.38
MHz
3
-
TYP.
Output Voltage
DCOUT(E)
Oscillation Frequency
FOSC
Maximum Duty Ratio
MAXDUTY
DCOUT=0V
100
-
-
%
4
Minimum Duty Ratio
MINDUTY
DCOUT=VIN
-
-
0
%
4
21
30
38
%
3
1.00
1.40
1.78
V
3
-
0.5
0.9
Ω
5
-
0.5
0.9
Ω
3
PFM Duty Ratio
PFMDUTY
U.V.L.O. Voltage (*2)
VUVLO
LX SW ‘High’ ON Resistance (*3)
RLXH
IDOUT=30mA
Connected to the external components,
IDOUT=10mA
Connected to the external components,
No load
Connected to the external components
DCOUT=0V, LX=VIN-0.05V
Connected to the external components,
LX SW ‘Low’ ON Resistance
RLXL
LX SW ‘High’ Leak Current (*12)
IleakH
VIN=LX=6.0V, CE=0V
-
0.05
1.00
μA
11
LX SW ‘Low’ Leak Current (*12)
IleakL
VIN=6.0V, LX=CE=0V
-
0.05
1.00
μA
11
Maximum Output Current
Imax1
Connected to the external components
600
-
-
mA
3
Current Limit (*9)
Ilim1
1.0
1.1
-
A
6
-
90
-
%
3
-
±100
-
2
5
10
ms
3
-
8
25
ms
10
Efficiency (*4)
EFFI
Output Voltage
Temperature Characteristics
U DCOUT
(UToprDCOUT)
Soft-Start Time
TSS
Latch Time (*5, 10)
Tlat
4/38
VIN=5.0V
Connected to the external components,
IDOUT=100mA
IDOUT=30mA
-40℃≦Topr≦85℃
Connected to the external components,
CE=0VtVIN, IDOUT=1mA
Connected to the external components,
VIN=CE=5.0V, Short DCOUT by 1Ω resistor
ppm/
℃
3
XC9508
Series
■ELECTRICAL CHARACTERISTICS (Continued)
XC9508xxxCAx (Continued)
●Regulator (1.8V product)
Topr=25℃
PARAMETER
SYMBOL
CONDITIONS
MIN.
TYP.
MAX.
1.764
1.800
200
-
1mA≦IROUT≦100mA
-
CIRCUIT
1.836
V
2
-
mA
2
15
50
mV
2
Output Voltage
VROUT(E)
Maximum Output Current
Imax2
Load Regulation
U VROUT
Dropout Voltage 1 (*6)
Vdif 1
IROUT=30mA
-
30
200
mV
2
Vdif 2
IROUT=100mA
-
100
200
mV
2
U VROUT
IROUT=30mA
-
0.05
0.25
%/V
2
240
300
-
mA
7
-
30
-
mA
7
-
60
-
dB
12
-
±100
-
Dropout Voltage 2
Line Regulation
IROUT=30mA
UNITS
UVINVROUT
VROUT(T)+1V≦VIN≦6V
Current Limit
Ilim2
VROUT=VROUT(E) x 0.9
Short-Circuit Current
Ishort
VROUT=VSS
Ripple Rejection Rate
VIN={VOUT(T)+1.0} VDC+0.5Vp-pAC,
PSRR
Output Voltage
U VROUT
Temperature Characteristics
UToprVROUT
IROUT=30mA, f=1kHz
IROUT=30mA
-40℃≦Topr≦85℃
ppm/
2
℃
●Detector (2.7V product)
PARAMETER
SYMBOL
Detect Voltage
VDF(E)
Hysteresis Range
VHYS
VD Output Current
IVD
Output Voltage
U VDF
Temperature Characteristics
UToprVDF
CONDITIONS
CE=0V
VHYS=[VDR(E)
(*11)
MIN.
TYP.
MAX.
UNITS
CIRCUIT
2.646
2.700
2.754
V
8
2
5
8
%
8
VDOUT=0.5V, CE=0V
- VDF(E)] / VDF(E) x 100
1
-
-
mA
9
-40℃≦Topr≦85℃
-
±100
-
ppm/
℃
8
Test conditions: Unless otherwise stated:
DC/DC: VIN=3.6V [@ DCOUT:2.2V]
VR: VIN = 2.8V (VIN=VROUT(T) + 1.0V)
VD: VIN=5.0V
Common conditions for all test items: CE=VIN, MODE=0V
* VROUT(T) : Setting output voltage
NOTE:
*1 : Including VD supply current (VD operates when in stand-by mode.)
*2 : Including hysteresis operating voltage range.
*3 : ON resistance (Ω)= 0.05 (V) / ILX (A)
*4 : EFFI = { ( Output Voltage x Output Current ) / ( Input Voltage x Input Current) } x 100
*5 : Time until it short-circuits DCOUT with GND through 1Ω of resistance from a state of operation and is set to DCOUT=0V from
current limit pulse generating.
*6 : Vdif = (VIN1 (*7) - VROUT1 (*8) )
*7 : VIN1 = The input voltage when VROUT1 appears as input voltage is gradually decreased.
*8 : VROUT1 = A voltage equal to 98% of the output voltage whenever an amply stabilized IOUT {VROUT(T) + 1.0V} is input.
*9 : Current limit = When VIN is low, limit current may not be reached because of voltage falls caused by ON resistance or serial
resistance of coils.
*10: Integral latch circuit=latch time may become longer and latch operation may not work when VIN is 3.0V or more.
*11: VDR(E) = VD release voltage
*12: When temperature is high, a current of approximately 5.0μA (maximum) may leak.
5/38
XC9508 Series
■TEST CIRCUITS
Circuit 1
Circuit 3
Circuit 5
6/38
Supply Current, Stand-by Current, CE Current,
MODE current
Circuit 2
Output Voltage (DC/DC) Oscillation Frequency, UVLO
Voltage, Soft-start Time, CE Voltage, Maximum Output
Current, Efficiency, (PFM Duty Cycle), (MODE Voltage)
Circuit 4
Lx ON Resistance
Output Voltage (VR), Load Regulation, Dropout Voltage,
Maximum Output Current, (MODE Voltage)
Circuit 6
Minimum Duty Cycle, Maximum Duty Cycle
Current Limit 1 (DC/DC)
XC9508
Series
■TEST CIRCUITS (Continued)
Circuit 7
Current Limit 2 (VR), Short Circuit Current (VR)
Circuit 8
Circuit 9
VD Output Current
Circuit 10
Circuit 11
Off-Leak
Circuit 12
Detect Voltage, Release Voltage (Hysteresis Range)
Latch Time
Ripple Rejection Rate
7/38
XC9508 Series
■TYPICAL APPLICATION CIRCUIT
FOSC
1.2MHz
600KHz
300kHz
L
4.7μH
(CDRH4D28C, SUMIDA)
10μH
(CDRH5D28, SUMIDA)
22μH
(CDRH6D28, SUMIDA)
MSOP-10 (TOP VIEW)
CIN
CL1
4.7μF
(ceramic, TAIYO YUDEN)
10μF
(ceramic, TAIYO YUDEN)
CL2 (*2)
VROUT≦2.0V
VROUT>2.0V
4.7μF (ceramic, TAIYO YUDEN)
Vdif>1.0V
1.0μF (ceramic, TAIYO YUDEN)
Vdif≦1.0V
4.7μF (ceramic, TAIYO YUDEN)
SD *1: XB0ASB03A1BR (TOREX)
*1 The DC/DC converter of the XC9508 series automatically switches between synchronous / non-synchronous. The Schottky diode is
not normally needed.
However, in cases where high efficiency is required when using the DC/DC converter during in the light load
while in non-synchronous operation, please connect a Schottky diode externally.
*2 Please be noted that the recommend value above of the CL2 may be changed depending on the input voltage value and setting voltage
value.
■OPERATIONAL EXPLANATION
The XC9508 series consists of a synchronous step-down DC/DC converter, a high speed LDO voltage regulator, and a
voltage detector. Since the LDO voltage regulator is stepped-down from the DC/DC's output, high efficiency and low noise
is possible even at lower output voltages.
●DC/DC Converter
The series consists of a reference voltage source, ramp wave circuit, error amplifier, PWM comparator, phase
compensation circuit, output voltage adjustment resistors, driver transistor, synchronous switch, current limiter circuit,
U.V.L.O. circuit and others. The series ICs compare, using the error amplifier, the voltage of the internal voltage
reference source with the feedback voltage from the VOUT pin through split resistors. Phase compensation is
performed on the resulting error amplifier output, to input a signal to the PWM comparator to determine the turn-on time
during PWM operation. The PWM comparator compares, in terms of voltage level, the signal from the error amplifier
with the ramp wave from the ramp wave circuit, and delivers the resulting output to the buffer driver circuit to cause the
Lx pin to output a switching duty cycle. This process is continuously performed to ensure stable output voltage. The
current feedback circuit monitors the P-channel MOS driver transistor current for each switching operation, and
modulates the error amplifier output signal to provide multiple feedback signals. This enables a stable feedback loop
even when a low ESR capacitor, such as a ceramic capacitor, is used, ensuring stable output voltage.
<Reference Voltage Source>
The reference voltage source provides the reference voltage to ensure stable output voltage of the DC/DC converter.
<Ramp Wave Circuit>
The ramp wave circuit determines switching frequency. The frequency is fixed internally and can be selected from
300kHz, 600 kHz and 1.2 MHz. Clock pulses generated in this circuit are used to produce ramp waveforms needed
for PWM operation, and to synchronize all the internal circuits.
<Error Amplifier>
The error amplifier is designed to monitor output voltage. The amplifier compares the reference voltage with the
feedback voltage divided by the internal split resistors. When a voltage lower than the reference voltage is fed back,
the output voltage of the error amplifier increases. The gain and frequency characteristics of the error amplifier output
are fixed internally to deliver an optimized signal to the mixer.
8/38
XC9508
Series
■OPERATIONAL EXPLANATION (Continued)
●DC/DC Converter (Continued)
<PWM/PFM>
The XC9508A series is PWM control, while the XC9508C series can be automatically switched between PWM control
and PWM/PFM control. The PWM of the XC9508A series is controlled on a specified frequency from light loads through
the heavy loads. Since the frequency is specified, the composition of a noise filter etc. becomes easy. However, the
efficiency at the time of the light load may become low.
The XC9508C series can switch in any timing between PWM control and PWM/PFM automatic switching control. The
series cannot control only PFM mode. If needed, the operation can be set on a specified frequency; therefore, the
control of the noise etc. is possible and the high efficiency at the time of the light load during PFM control mode is
possible. With the automatic PWM/PFM switching control function, the series ICs are automatically switched from
PWM control to PFM control mode under light load conditions. If during light load conditions the coil current becomes
discontinuous and on-time rate falls lower than 30%, the PFM circuit operates to output a pulse with 30% of a fixed
on-time rate from the Lx pin. During PFM operation with this fixed on-time rate, pulses are generated at different
frequencies according to conditions of the moment. This causes a reduction in the number of switching operations per
unit of time, resulting in efficiency improvement under light load conditions. However, since pulse output frequency is
not constant, consideration should be given if a noise filter or the like is needed. Necessary conditions for switching to
PFM operation depend on input voltage, load current, coil value and other factors.
<Synchronous / Non-synchronous>
The XC9508 series automatically switches between synchronous / non-synchronous according to the state of the DC/DC
converter. Highly efficient operations are achievable using the synchronous mode while the coil current is in a
continuous state. The series enters non-synchronous operation when the built-in N-ch switching transistor for
synchronous operation is shutdown, which happens when the load current becomes low and the operation changes to a
discontinuous state. The IC can operate without an external schottky diode because the parasitic diode in the N-ch
switching transistor provides the circuit's step-down operation. However, since Vf of the parasitic diode is a high 0.6V,
the efficiency level during non-synchronous operation shows a slight decrease.
Please use an external schottky diode
if high efficiency is required during light load current.
●Continuous Mode: Synchronous
●Discontinuous Mode: Non-Synchronous
9/38
XC9508 Series
■OPERATIONAL EXPLANATION (Continued)
●DC/DC Converter (Continued)
<Current Limit>
The current limiter circuit of the XC9508 series monitors the current flowing through the P-channel MOS driver transistor
connected to the Lx pin, and features a combination of the constant-current type current limit mode and the operation
suspension mode.
① When the driver current is greater than a specific level, the constant-current type current limit function operates to
turn off the pulses from the Lx pin at any given timing.
② When the driver transistor is turned off, the limiter circuit is then released from the current limit detection state.
③ At the next pulse, the driver transistor is turned on. However, the transistor is immediately turned off in the case of
an over current state.
④ When the over current state is eliminated, the IC resumes its normal operation.
The IC waits for the over current state to end by repeating the steps ① through ③ . If an over current state
continues for 8msec* and the above three steps are repeatedly performed, the IC performs the function of latching
the OFF state of the driver transistor, and goes into operation suspension mode. Once the IC is in suspension
mode, operations can be resumed by either turning the IC off via the CE/MODE pin, or by restoring power to the VIN
pin. The suspension mode does not mean a complete shutdown, but a state in which pulse output is suspended;
therefore, the internal circuitry remains in operation. The constant-current type current limit of the XC9508 series
can be set at 1.1A for MSOP-10 package and 0.7A for USP-10 package
<U.V.L.O. Circuit>
When the VIN pin voltage becomes 1.4 V or lower, the P-channel output driver transistor is forced OFF to prevent false
pulse output caused by unstable operation of the internal circuitry. When the VIN pin voltage becomes 1.8 V or higher,
switching operation takes place. By releasing the U.V.L.O. function, the IC performs the soft start function to initiate
output startup operation. The soft start function operates even when the VIN pin voltage falls momentarily below the
U.V.L.O. operating voltage. The U.V.L.O. circuit does not cause a complete shutdown of the IC, but causes pulse
output to be suspended; therefore, the internal circuitry remains in operation.
●High Speed LDO Voltage Regulator
The voltage regulator block of the XC9508 series consists of a reference voltage source, error amplifier, and current
limiter circuit. The voltage divided by split resistors is compared with the internal reference voltage by the error
amplifier. The P-channel MOSFET, which is connected to the VROUT pin, is then driven by the subsequent output
signal. The output voltage at the VROUT pin is controlled and stabilized by a system of negative feedback. A stable
output voltage is achievable even if used with low ESR capacitors as a phase compensation circuit is built-in.
<Reference Voltage Source>
The reference voltage source provides the reference voltage to ensure stable output voltage of the regulator.
<Error Amplifier>
The error amplifier compares the reference voltage with the signal from VROUT, and the amplifier controls the output of
the Pch driver transistor.
<Current Limit Circuit>
The voltage regulator block includes a combination of a constant current limiter circuit and a foldback circuit. When the
load current reaches the current limit level, the current limiter circuit operates and the output voltage of the voltage
regulator block drops. As a result of this drop in output voltage, the foldback circuit operates, output voltage drops
further and the load current decreases. When the VROUT and GND pin are shorted, the load current of about 30mA flows.
10/38
XC9508
Series
■OPERATIONAL EXPLANATION (Continued)
●Voltage Detector
The detector block of the XC9508 series detects output voltage from the VDOUT pin to the signal, which enters from VDIN.
(N-channel Open Drain Type)
<CE Pin Function>
The operation of the XC9508 series' DC/DC converter block and voltage regulator block will enter into the shut down
mode when a low level signal is input to the CE pin. During the shut down mode, the current consumption occurs only in
the detector and is 0.6μA (TYP.), with a state of high impedance at the Lx pin and DCOUT pin. The IC starts its operation
by inputting a high level signal to the CE pin. The input to the CE pin is a CMOS input and the sink current is 0μA
(TYP.).
<MODE Pin Function>
The operation of the XC9508A series' voltage detector block will enter into stand-by mode when a high level signal is input
to the MODE pin. When a low level signal is input, the voltage regulator block will enter into stand-by mode. However,
if the IC enters into stand-by mode via the CE pin, the voltage regulator block also shuts down. With the XC9508C
series control can be PWM control when the MODE pin is 'H' level and PWM/PFM automatic switching control when the
MODE pin is 'L' level.
■NOTES ON USE
●Application Information
1.
The XC9508 series is designed for use with ceramic output capacitors. If, however, the potential difference between
dropout voltage or output current is too large, a ceramic capacitor may fail to absorb the resulting high switching
energy and oscillation could occur on the output. If the input-output potential difference is large, connect an
electrolytic capacitor in parallel to compensate for insufficient capacitance.
2.
Spike noise and ripple voltage arise in a switching regulator as with a DC/DC converter. These are greatly
influenced by external component selection, such as the coil inductance, capacitance values, and board layout of
external components. Once the design has been completed, verification with actual components should be done.
3. When the difference between VIN and VOUT is large in PWM control, very narrow pulses will be outputted, and there
is the possibility that some cycles may be skipped completely.
4. When the difference between VIN and VOUT is small, and the load current is heavy, very wide pulses will be outputted
and there is the possibility that some cycles may be skipped completely: in this case, the Lx pin may not go low at all.
●DC/DC Waveform (3.3V, 1.2MHz)
< External Components>
L:4.7μH(CDRH4D28C,SUMIDA)
CIN:4.7μF(ceramic)
CL:10μF(ceramic)
< External Components>
L:4.7μH(CDRH4D28C,SUMIDA)
CIN:4.7μF(ceramic)
CL:10μF(ceramic)
11/38
XC9508 Series
■NOTES ON USE (Continued)
●Application Information (Continued)
5.
The IC's DC/DC converter operates in synchronous mode when the coil current is in a continuous state and
non-synchronous mode when the coil current is in a discontinuous state. In order to maintain the load current
value when synchronous switches to non-synchronous and vise versa, a ripple voltage may increase because of the
repetition of switching between synchronous and non-synchronous. When this state continues, the increase in the
ripple voltage stops. To reduce the ripple voltage, please increase the load capacitance value or use a Schottky
diode externally. When the current used becomes close to the value of the load current when synchronous
switches to non- synchronous and vise versa, the switching current value can be changed by changing the coil
inductance value. In case changes to coil inductance are to values other than the recommended coil inductance
values, verification with actual components should be done.
Ics =
(VIN - DCOUT) x OnDuty / (L x Fosc)
Ics: Switching current from synchronous rectification to non-synchronous rectification
.
OnDuty: OnDuty ratio of P-ch driver transistor ( =.step down ratio : DCOUT / VIN)
L: Coil inductance value
Fosc: Oscillation frequency
IDOUT: The DC/DC load current (the sum of the DC/DC's and the regulator's load if the regulator has load.)
6. When the XC9508C series operates in PWM/PFM automatic switching control mode, the reverse current may
become quite high around the load current value when synchronous switches to non-synchronous and vise versa
(also refer to no. 5 above). Under this condition, switching synchronous rectification and non-synchronous
rectification may be repeated because of the reverse current, and the ripple voltage may be increased to 100mV or
more. The reverse current is the current that flows in the PGND direction through the N-ch driver transistor from
the coil. The conditions, which cause this operation, are as follows.
PFM Duty<Step down ratio = DCOUT / VIN×100 (%)
PFM Duty: 30% (TYP.)
Please switch to PWM control via the MODE function in cases where the load current value of the DC/DC converter
is close to synchronous.
●DC/DC Waveform (1.8V, 600kHz) @ VIN=6.0V
< External Components>
L:10μH(CDRH5D28C,SUMIDA)
CIN:4.7μF(ceramic)
CL:10μF(ceramic)
Step down ratio: 1.8V / 6.0V=30% <PFM Duty 31%>
12/38
XC9508
Series
■NOTES ON USE (Continued)
●Application Information (Continued)
7. With the DC/DC converter of the IC, the peak current of the coil is controlled by the current limit circuit. Since the
peak current increases when dropout voltage or load current is high, current limit starts operating, and this can lead
to instability. When peak current becomes high, please adjust the coil inductance value and fully check the circuit
operation. In addition, please calculate the peak current according to the following formula:
Peak current: Ipk = (VIN - DCOUT)×OnDuty / (2×L×Fosc) + IDOUT
8. When the peak current, which exceeds limit current flows within the specified time, the built-in driver transistor is
turned off (the integral latch circuit). During the time until it detects limit current and before the built-in transistor can
be turned off, the current for limit current flows; therefore, care must be taken when selecting the rating for the coil or
the Schottky diode.
9. When VIN is low, limit current may not be reached because of voltage falls caused by ON resistance or serial
resistance of the coil.
10.
In the integral latch circuit, latch time may become longer and latch operation may not work when VIN is 3.0V or
more.
11.
Use of the IC at voltages below the recommended voltage range may lead to instability.
12.
This IC and the external components should be used within the stated absolute maximum ratings in order to prevent
damage to the device.
13. Since the DC/DC converter and the regulator of the XC9508 series are connected in series, the sum of the output
current (IDOUT) of the DC/DC and the output current (IROUT) of the VR makes the current flows inside the DC/DC
converter. Please be careful of the power dissipation when in use. Please calculate power dissipation by using
the following formula.
Pd=PdDC/DC + PdVR
2
DC/DC power dissipation (when in synchronous operation) : PdDC/DC = IDOUT ×RON
VR power dissipation: PdVR=(DCOUT – VROUT)×IROUT
RON: ON resistance of the built-in driver transistor to the DC/DC (= 0.5Ω <TYP.>)
RON=Rpon×P-chOnDuty / 100 + Rnon×(1 – P-chOnDuty / 100)
14.
The voltage detector circuit built-in the XC9508 series internally monitor the VDD pin voltage, the DC/DC output pin
voltage and VR output pin voltage. Please determine the detect voltage value (VDF) by the following equation.
VDF≦(Setting voltage on both the DCOUT voltage and the VROUT voltage)×85%*
* An assumed value of tolerance among the DCOUT voltage, the VROUT voltage, and the VD release voltage
(The VD detect voltage and hysteresis range).
13/38
XC9508 Series
■NOTES ON USE (Continued)
●Instructions on Pattern Layout
1.
In order to stabilize VIN's voltage level, we recommend that a by-pass capacitor (CIN) be connected as close as
possible to the VDD & AGND pins. This IC is the composite IC of the DC/DC converter and regulator. Fluctuation
of the VIN's voltage level causes mutual interference.
2.
Please mount each external component as close to the IC as possible.
3. Wire external components as close to the IC as possible and use thick, short connecting traces to reduce the circuit
impedance.
4.
Make sure that the PCB GND traces are as thick as possible, as variations in ground potential caused by high
ground currents at the time of switching may result in instability of the DC/DC converter and have adverse influence
on the regulator output.
5.
If using a Schottky diode, please connect the anode side to the AGND pin through CIN.
caused by the noise may occur depending on the arrangement of the Schottky diode.
<MSOP-10 Reference pattern layout>
14/38
Characteristic degradation
XC9508
Series
■TYPICAL PERFORMANCE CHARACTERISTICS
(A) DC/DC CONVERTER
(1) Efficiency vs. Output Current
15/38
XC9508 Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(A) DC/DC CONVERTER (Continued)
(2) Output Voltage vs. Output Current
16/38
XC9508
Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(A) DC/DC CONVERTER (Continued)
(3) Output Voltage vs. Ripple Voltage
17/38
XC9508 Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(A) DC/DC CONVERTER (Continued)
(4) Output Voltage vs. Ambient Temperature
(5) Soft Start Time vs. Ambient Temperature
18/38
XC9508
Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(A) DC/DC CONVERTER (Continued)
(6) DC/DC Supply Current vs. Ambient Temperature (VR: Shutdown)*
19/38
XC9508 Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(A) DC/DC CONVERTER (Continued)
(7) LX Pch/Nch on Resistance vs. Input Voltage
(8) Oscillation Frequency vs. Ambient Temperature
20/38
(9) U.V.L.O. Voltage vs. Ambient Temperature
XC9508
Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(A) DC/DC CONVERTER (Continued)
(10-1) DC/DC Load Transient Response (DCOUT: 1.8V, FOSC: 1.2MHz)
(a) PWM Control
(b) PWM/PFM Automatic Switching Control* (*XC9508C Series Only)
21/38
XC9508 Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(A) DC/DC CONVERTER (Continued)
(10-2) DC/DC Load Transient Response (*DCOUT: 3.3V, FOSC: 1.2MHz)
(a) PWM Control
(b) PWM/PFM Automatic Switching Control* (*XC9508C Series Only)
22/38
XC9508
Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(A) DC/DC CONVERTER (Continued)
(10-3) DC/DC Load Transient Response (*DCOUT: 1.8V, FOSC: 600kHz)
(a) PWM Control
(b) PWM/PFM Automatic Switching Control* (*XC9508C Series Only)
23/38
XC9508 Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(A) DC/DC CONVERTER (Continued)
(10-4) DC/DC Load Transient Response (*DCOUT: 3.3V, FOSC: 600kHz)
(a) PWM Control
(b) PWM/PFM Automatic Switching Control* (*XC9508C Series Only)
24/38
XC9508
Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(B) VOLTAGRE REGULATOR
(1) Output Voltage vs. Input Voltage
25/38
XC9508 Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(B) VOLTAGRE REGULATOR (Continued)
(2) Output Voltage vs. Output Current (Current Limit)
26/38
XC9508
Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(B) VOLTAGRE REGULATOR (Continued)
(3) Dropout Voltage vs. Output Current
27/38
XC9508 Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(B) VOLTAGRE REGULATOR (Continued)
(4) Output Voltage vs. Output Current
28/38
XC9508
Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(B) VOLTAGRE REGULATOR (Continued)
(5) Output Voltage vs. Ambient Temperature
29/38
XC9508 Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(B) VOLTAGRE REGULATOR (Continued)
(6) Ripple Rejection Ratio vs. Ripple Frequency
30/38
XC9508
Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(B) VOLTAGRE REGULATOR (Continued)
(7) VR Load Transient Response
31/38
XC9508 Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(C) VOLTAGE DETECTOR
(1) Output Current vs. Input Voltage
(2) Detect Voltage vs. Input Voltage
32/38
XC9508
Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(C) VOLTAGE DETECTOR (Continued)
(3) Detect Voltage, Release Voltage vs. Ambient Temperature
33/38
XC9508 Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(D) COMMON
(1) Supply Current vs. Ambient Temperature (DC/DC & VR & VD)
(2) Shutdown Current vs. Input Voltage
34/38
(3) Shutdown Current vs. Ambient Temperature
XC9508
Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(D) COMMON (Continued)
(4) CE Pin Threshold Voltage vs. Ambient Temperature
Ambient Temperature : Ta (℃)
(5) MODE Pin Threshold Voltage vs. Ambient Temperature
Ambient Temperature : Ta (℃)
35/38
XC9508 Series
■PACKAGING INFORMATION
●USP-10
●MSOP-10
* Soldering fillet surface is not
formed because the sides of
the pins are not plated.
●USP-10 Recommended Pattern Layout
2.3
36/38
●USP-10 Recommended Metal Mask Design
XC9508
Series
■MARKING RULE
●MSOP-10, USP-10
①Represents product series
MARK
7
USP-10
(TOP VIEW)
PRODUCT SERIES
XC9508xxxxxx
②Represents DC/DC control methods and MODE pin
DC/DC
MODE PIN
MODE PIN
PRODUCT SERIES
CONTROL
(H level)
(L level)
PWM Control
VR: OFF
VR: ON
XC9508Axxxxx
PWM, PFM/PWM PFM/PWM
PWM Control
XC9508Cxxxxx
Manual Switching Auto Switching
Custom
XC9508Cxxxxx
MARK
A
C
S
③④Represents detect voltage DC/DC,VR and VD
ex)
MARK
③
1
④
5
DC/DC
VR
VD
PRODUCT SERIES
2.0V
1.5V
1.9V
XC9508x15xxx
MSOP-10
(TOP VIEW)
⑤Represents oscillation frequency
MARK
3
6
C
OSCILLATION FREQUENCY
300kHz
600kHz
1.2MHz
PRODUCT SERIES
XC9508xxx3xx
XC9508xxx6xx
XC9508xxxCxx
⑥Represents production lot number
0 to 9, A to Z reverse character 0 to 9, A to Z repeated (G, I, J, O, Q, W excepted)
Note: No character inversion used.
37/38
XC9508 Series
1. The products and product specifications contained herein are subject to change without
notice to improve performance characteristics.
Consult us, or our representatives
before use, to confirm that the information in this catalog is up to date.
2. We assume no responsibility for any infringement of patents, patent rights, or other
rights arising from the use of any information and circuitry in this catalog.
3. Please ensure suitable shipping controls (including fail-safe designs and aging
protection) are in force for equipment employing products listed in this catalog.
4. The products in this catalog are not developed, designed, or approved for use with such
equipment whose failure of malfunction can be reasonably expected to directly
endanger the life of, or cause significant injury to, the user.
(e.g. Atomic energy; aerospace; transport; combustion and associated safety
equipment thereof.)
5. Please use the products listed in this catalog within the specified ranges.
Should you wish to use the products under conditions exceeding the specifications,
please consult us or our representatives.
6. We assume no responsibility for damage or loss due to abnormal use.
7. All rights reserved. No part of this catalog may be copied or reproduced without the
prior permission of Torex Semiconductor Ltd.
38/38