Marketing Bulletin DATE: May 20, 2003 TO: Affected Customers FROM: Mark Stoner RE: Product Termination To all concerned parties, This bulletin is to notify all customers of the termination of the following Ecliptek series effective May 14th, 2003: Series E11C1 E13C1 E11C2 E13C2 E31C2 E32C2 Description Four Pad SMD PECL Oscillator, 5V Four Pad SMD PECL Oscillator, 3.3V Six Pad SMD PECL Oscillator, 5V Six Pad SMD PECL Oscillator, 3.3V Six Pad SMD PECL VCXO, 5V Six Pad SMD PECL VCXO, 3.3V Recommended Replacement E11J1 or E11W1 E13J1 or E13W1 E11J2 or E11W2 E13J2 or E13W2 E31J2 or E31W2 E32J2 or E32W2 Because of the circumstances surrounding this termination, there will be no end-of-life policy exercised. The series will be terminated with no purchasing or lifetime buy window available. All of us at Ecliptek Corporation apologize for any inconvenience this may have caused and can assure you we are taking measures to insure this will not happen again in the future. Best Regards, Mark W. Stoner Director of Marketing Ecliptek Corporation 3545 CADILLAC AVENUE • COSTA MESA, CA 92626-1401 • (714) 433-1200 • Fax (714) 433-1234 E11C1 Series E11C1 • PECL Output Oscillators • 5.0V supply voltage • 4 pad ceramic SMD package with J-leads • Stability to 20ppm • Output Enable/Disable available • Complementary Output available • Available on Tape and Reel H 5.1 L 14.2 W 9.85 OSCILLATOR NOTES OBSOLETE __________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ ________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ ELECTRICAL SPECIFICATIONS Frequency Range 19.440MHz to 212.500MHz Operating Temperature Range 0°C to 70°C or -40°C to 85°C Storage Temperature Range -55°C to 125°C Supply Voltage (VCC) 5.0VDC ±5% Input Current 100mA Maximum Logic Type 100KH Frequency Tolerance / Stability Inclusive of Operating Temp Range, Supply Voltage, ±100ppm, ±50ppm, ±25ppm, or Load, and Aging @25°C over 10 years ±20ppm Maximum Output Voltage Logic High (VOH) VCC-1.025VDC Minimum Output Voltage Logic Low (VOL) VCC-1.620VDC Maximum Rise Time / Fall Time 20% to 80% of waveform 2 nSeconds Maximum Duty Cycle at 50% of waveform 50 ±10(%) 50 ±5(%) Load Drive Capability 50 Ohms into VCC-2.0VDC Logic Control / Additional Output No Connect, Enable/Disable, or Complementary Output Enable/Disable Input Voltage VIL of VCC-1.475VDC Maximum Enables Output No Connection Enables Output VIH of VCC-1.165VDC Minimum Disables Output: Logic Low, Disables Complementary Output: Logic High Start Up Time 10 mSeconds Maximum RMS Phase Jitter FJ = 12kHz to 20MHz 1 pSec Maximum MANUFACTURER CATEGORY SERIES PACKAGE VOLTAGE CLASS REV.DATE ECLIPTEK CORP. OSCILLATOR E11C1 CERAMIC 5.0V OS65 10/02 800-ECLIPTEK www.ecliptek.com for latest revision 152 Specifications subject to change without notice. PART NUMBERING GUIDE E11C1 F 2 C - 155.520M TR FREQUENCY TOLERANCE & STABILITY/ OPERATING TEMPERATURE RANGE C=±100ppm Maximum over 0°C to +70°C D=±50ppm Maximum over 0°C to +70°C E=±25ppm Maximum over 0°C to +70°C F=±20ppm Maximum over 0°C to +70°C G=±100ppm Maximum over -40°C to +85°C H=±50ppm Maximum over -40°C to +85°C AVAILABLE OPTIONS Blank=Tubes TR=Tape and Reel (Standard) FREQUENCY LOGIC CONTROL/ADDITIONAL OUTPUT A=No Connect B=Enable/Disable C=Complementary Output DUTY CYCLE 1=50% ±10%, 2=50% ±5% MECHANICAL DIMENSIONS SUGGESTED SOLDER PAD LAYOUT ALL DIMENSIONS IN MILLIMETERS ALL DIMENSIONS IN MILLIMETERS Tolerances = ±0.1 Pin 1: Complementary Output, No Connect, or Enable/Disable Pin 2: Case Ground Pin 3: Output Pin 4: Supply Voltage TAPE AND REEL DIMENSIONS ALL DIMENSIONS IN MILLIMETERS TAPE F 12 ±.1 A B C D E 24 ±.3 11.5 ±.1 10.75 ±.1 4 ±.2 2±.1 F M N O P Q 1.5 MIN 50 MIN 20.2 MIN 13±.2 40 MIN QTY/REEL 1000 REEL G H J K L R S T U V B0* 1.5 +.1-0 A0* .4 ±.05 K0* 2.5 MIN 10 MIN 30.4 MAX 360 MAX 24.4+2-0 *Compliant to EIA 481A ENVIRONMENTAL/MECHANICAL SPECIFICATIONS MARKING SPECIFICATIONS Characteristic Specification Line 1: ECLIPTEK Seal Integrity Bubble test in Perfluorocarbon at +125°C ±5°C for 60 seconds minimum (internal crystal only). Line 2: XX.XXX M OBSOLETE Solderability Sn63 Solder dip at +230°C ±5°C for 5 seconds/95% coverage. Marking Permanency 10 Strokes with brush after 1 minute soak in solvent, 3 times. Shock Random drop on hard wooden plate 3 times from a height of 20cm. Vibration Frequency in MHz (5 Digits Maximum + Decimal) Line 3: XX Y ZZ Week of Year Last Digit of Year Ecliptek Manufacturing Identifier Frequency with an amplitude of 1.5mm sweeping between 10Hz to 55Hz within 1 minute (approximately) for 2 hours minimum on each axis (X, Y and Z) for a total of 6 hours. MANUFACTURER CATEGORY SERIES PACKAGE VOLTAGE CLASS REV.DATE ECLIPTEK CORP. OSCILLATOR E11C1 CERAMIC 5.0V OS65 10/02 800-ECLIPTEK www.ecliptek.com for latest revision 153 Specifications subject to change without notice. E11C2 Series E11C2 • PECL Output Oscillators • 5.0V supply voltage • 6 pad ceramic SMD package with J-leads • Stability to 20ppm • Output Enable/Disable available • Complementary Output available • Available on Tape and Reel NOTES H 5.1 L 14.2 W 9.85 OSCILLATOR OBSOLETE __________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ ELECTRICAL SPECIFICATIONS Frequency Range 19.440MHz to 212.500MHz Operating Temperature Range 0°C to 70°C or -40°C to 85°C Storage Temperature Range -55°C to 125°C Supply Voltage (VCC) 5.0VDC ±5% Input Current 100mA Maximum Logic Type 100KH Frequency Tolerance / Stability Inclusive of Operating Temp Range, Supply Voltage, ±100ppm, ±50ppm, ±25ppm, or Load, and Aging @25°C over 10 years ±20ppm Maximum Output Voltage Logic High (VOH) VCC-1.025VDC Minimum Output Voltage Logic Low (VOL) VCC-1.620VDC Maximum Rise Time / Fall Time 20% to 80% of waveform 2 nSeconds Maximum Duty Cycle at 50% of waveform 50 ±10(%) 50 ±5(%) Load Drive Capability 50 Ohms into VCC-2.0VDC Logic Control / Additional Output No Connect, Enable/Disable, Complementary Output, or Complementary Output and Enable/Disable Enable/Disable Input Voltage VIL of VCC-1.475VDC Maximum Enables Output No Connection Enables Output VIH of VCC-1.165VDC Minimum Disables Output: Logic Low Disables Complementary Output: Logic High Start Up Time 10 mSeconds Maximum RMS Phase Jitter FJ = 12kHz to 20MHz 1 pSec Maximum MANUFACTURER CATEGORY SERIES PACKAGE VOLTAGE CLASS ECLIPTEK CORP. OSCILLATOR E11C2 CERAMIC 5.0V OS66 800-ECLIPTEK www.ecliptek.com for latest revision 154 REV.DATE 10/02 Specifications subject to change without notice. PART NUMBERING GUIDE E11C2 F 2 C - 155.520M TR FREQUENCY TOLERANCE & STABILITY/ OPERATING TEMPERATURE RANGE C=±100ppm Maximum over 0°C to +70°C D=±50ppm Maximum over 0°C to +70°C E=±25ppm Maximum over 0°C to +70°C F=±20ppm Maximum over 0°C to +70°C G=±100ppm Maximum over -40°C to +85°C H=±50ppm Maximum over -40°C to +85°C AVAILABLE OPTIONS Blank=Tubes TR=Tape and Reel (Standard) FREQUENCY LOGIC CONTROL/ADDITIONAL OUTPUT A=No Connect D=Complementary Output and Enable/Disable B=Enable/Disable E=Complementary Output (Alt. Pin Configuration) C=Complementary Output G=Complementary Output and Enable/Disable (Alt. Pin Configuration) DUTY CYCLE 1=50% ±10%, 2=50% ±5% MECHANICAL DIMENSIONS PIN CONNECTIONS TABLE ALL DIMENSIONS IN MILLIMETERS TAPE AND REEL DIMENSIONS ALL DIMENSIONS IN MILLIMETERS TAPE F 12 ±.1 A B C D E 24 ±.3 11.5 ±.1 10.75 ±.1 4 ±.2 2±.1 F M N O P Q 1.5 MIN 50 MIN 20.2 MIN 13±.2 40 MIN QTY/REEL 1000 REEL G H J K L R S T U V B0* 1.5 +.1-0 A0* .4 ±.05 K0* 2.5 MIN 10 MIN 30.4 MAX 360 MAX 24.4+2-0 *Compliant to EIA 481A ENVIRONMENTAL/MECHANICAL SPECIFICATIONS Characteristic MARKING SPECIFICATIONS Line 1: ECLIPTEK Specification OBSOLETE Seal Integrity Bubble test in Perfluorocarbon at +125°C ±5°C for 60 seconds minimum (internal crystal only). Solderability Sn63 Solder dip at +230°C ±5°C for 5 seconds/95% coverage. Marking Permanency 10 Strokes with brush after 1 minute soak in solvent, 3 times. Shock Random drop on hard wooden plate 3 times from a height of 20cm. Vibration Frequency with an amplitude of 1.5mm sweeping between 10Hz to 55Hz within 1 minute (approximately) for 2 hours minimum on each axis (X, Y and Z) for a total of 6 hours. MANUFACTURER CATEGORY SERIES ECLIPTEK CORP. OSCILLATOR E11C2 800-ECLIPTEK www.ecliptek.com for latest revision Line 2: XX.XXX M Frequency in MHz (5 Digits Maximum + Decimal) Line 3: XX Y ZZ PACKAGE CERAMIC 155 Week of Year Last Digit of Year Ecliptek Manufacturing Identifier VOLTAGE CLASS REV.DATE 5.0V OS66 10/02 Specifications subject to change without notice. E13C1 Series E13C1 • PECL Output Oscillators • 3.3V supply voltage • 4 pad ceramic SMD package with J-leads • Stability to 20ppm • Output Enable/Disable available • Complementary Output available • Available on Tape and Reel H 5.1 L 14.2 W 9.85 OSCILLATOR NOTES __________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ OBSOLETE _________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ ________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ ELECTRICAL SPECIFICATIONS Frequency Range 19.440MHz to 212.500MHz Operating Temperature Range 0°C to 70°C or -40°C to 85°C Storage Temperature Range -55°C to 125°C Supply Voltage (VCC) 3.3VDC ±5% Input Current 75mA Maximum Logic Type 100KH Frequency Tolerance / Stability Inclusive of Operating Temp Range, Supply Voltage, ±100ppm, ±50ppm, ±25ppm, or Load, and Aging @25°C over 10 years ±20ppm Maximum Output Voltage Logic High (VOH) VCC-1.025VDC Minimum Output Voltage Logic Low (VOL) VCC-1.620VDC Maximum Rise Time / Fall Time 20% to 80% of waveform 2 nSeconds Maximum Duty Cycle at 50% of waveform 50 ±10(%) 50 ±5(%) Load Drive Capability 50 Ohms into VCC-2.0VDC Logic Control / Additional Output No Connect, Enable/Disable, or Complementary Output Enable/Disable Input Voltage VIL of VCC-1.475VDC Maximum Enables Output No Connection Enables Output VIH of VCC-1.165VDC Minimum Disable Output: Logic Low Disables Complementary Output: Logic High Start Up Time 10 mSeconds Maximum RMS Phase Jitter FJ = 12kHz to 20MHz 1 pSec Maximum MANUFACTURER CATEGORY SERIES PACKAGE VOLTAGE CLASS REV.DATE ECLIPTEK CORP. OSCILLATOR E13C1 CERAMIC 3.3V OS63 10/02 800-ECLIPTEK www.ecliptek.com for latest revision 156 Specifications subject to change without notice. PART NUMBERING GUIDE E13C1 F 2 C - 155.520M TR FREQUENCY TOLERANCE & STABILITY/ OPERATING TEMPERATURE RANGE C=±100ppm Maximum over 0°C to +70°C D=±50ppm Maximum over 0°C to +70°C E=±25ppm Maximum over 0°C to +70°C F=±20ppm Maximum over 0°C to +70°C G=±100ppm Maximum over -40°C to +85°C H=±50ppm Maximum over -40°C to +85°C AVAILABLE OPTIONS Blank=Tubes TR=Tape and Reel (Standard) FREQUENCY LOGIC CONTROL/ADDITIONAL OUTPUT A=No Connect B=Enable/Disable C=Complementary Output DUTY CYCLE 1=50% ±10%, 2=50% ±5% MECHANICAL DIMENSIONS SUGGESTED SOLDER PAD LAYOUT ALL DIMENSIONS IN MILLIMETERS ALL DIMENSIONS IN MILLIMETERS Tolerances = ±0.1 Pin 1: Complementary Output, No Connect, or Enable/Disable Pin 2: Case Ground Pin 3: Output Pin 4: Supply Voltage TAPE AND REEL DIMENSIONS ALL DIMENSIONS IN MILLIMETERS TAPE F 12 ±.1 A B C D E 24 ±.3 11.5 ±.1 10.75 ±.1 4 ±.2 2±.1 F M N O P Q 1.5 MIN 50 MIN 20.2 MIN 13±.2 40 MIN QTY/REEL 1000 REEL G H J K L R S T U V B0* 1.5 +.1-0 A0* .4 ±.05 K0* 2.5 MIN 10 MIN 30.4 MAX 360 MAX 24.4+2-0 *Compliant to EIA 481A ENVIRONMENTAL/MECHANICAL SPECIFICATIONS MARKING SPECIFICATIONS Characteristic Specification Line 1: ECLIPTEK Seal Integrity Bubble test in Perfluorocarbon at +125°C ±5°C for 60 seconds minimum (internal crystal only). Line 2: XX.XXX M Solderability Sn63 Solder dip at +230°C ±5°C for 5 seconds/95% coverage. Marking Permanency 10 Strokes with brush after 1 minute soak in solvent, 3 times. Shock Random drop on hard wooden plate 3 times from a height of 20cm. Vibration Frequency with an amplitude of 1.5mm sweeping between 10Hz to 55Hz within 1 minute (approximately) for 2 hours minimum on each axis (X, Y and Z) for a total of 6 hours. OBSOLETE Frequency in MHz (5 Digits Maximum + Decimal) Line 3: XX Y ZZ Week of Year Last Digit of Year Ecliptek Manufacturing Identifier MANUFACTURER CATEGORY SERIES PACKAGE VOLTAGE CLASS REV.DATE ECLIPTEK CORP. OSCILLATOR E13C1 CERAMIC 3.3V OS63 10/02 800-ECLIPTEK www.ecliptek.com for latest revision 157 Specifications subject to change without notice. E13C2 Series E13C2 • PECL Output Oscillators • 3.3V supply voltage • 6 pad ceramic SMD package with J-leads • Stability to 20ppm • Output Enable/Disable available • Complementary Output available • Available on Tape and Reel H 5.1 L 14.2 W 9.85 OSCILLATOR NOTES OBSOLETE __________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ ELECTRICAL SPECIFICATIONS Frequency Range 19.440MHz to 212.500MHz Operating Temperature Range 0°C to 70°C or -40°C to 85°C Storage Temperature Range -55°C to 125°C Supply Voltage (VCC) 3.3VDC ±5% Input Current 75mA Maximum Logic Type 100KH Frequency Tolerance / Stability Inclusive of Operating Temp Range, Supply Voltage, ±100ppm, ±50ppm, ±25ppm, or Load, and Aging @25°C over 10 years ±20ppm Maximum Output Voltage Logic High (VOH) VCC-1.025VDC Minimum Output Voltage Logic Low (VOL) VCC-1.620VDC Maximum Rise Time / Fall Time 20% to 80% of waveform 2 nSeconds Maximum Duty Cycle at 50% of waveform 50 ±10(%) 50 ±5(%) Load Drive Capability 50 Ohms into VCC-2.0VDC Logic Control / Additional Output No Connect, Enable/Disable, Complementary Output, or Complementary Output and Enable/Disable Enable/Disable Input Voltage VIL of VCC-1.475VDC Maximum Enables Output No Connection Enables Output VIH of VCC-1.165VDC Minimum Disables Output: Logic Low Disables Complementary Output: Logic High Start Up Time 10 mSeconds Maximum RMS Phase Jitter FJ = 12kHz to 20MHz 1 pSec Maximum MANUFACTURER CATEGORY SERIES PACKAGE VOLTAGE CLASS REV.DATE ECLIPTEK CORP. OSCILLATOR E13C2 CERAMIC 3.3V OS64 10/02 800-ECLIPTEK www.ecliptek.com for latest revision 158 Specifications subject to change without notice. PART NUMBERING GUIDE E13C2 F 2 C - 155.520M TR FREQUENCY TOLERANCE & STABILITY/ OPERATING TEMPERATURE RANGE C=±100ppm Maximum over 0°C to +70°C D=±50ppm Maximum over 0°C to +70°C E=±25ppm Maximum over 0°C to +70°C F=±20ppm Maximum over 0°C to +70°C G=±100ppm Maximum over -40°C to +85°C H=±50ppm Maximum over -40°C to +85°C AVAILABLE OPTIONS Blank=Tubes TR=Tape and Reel (Standard) FREQUENCY LOGIC CONTROL/ADDITIONAL OUTPUT A=No Connect D=Complementary Output and Enable/Disable B=Enable/Disable E=Complementary Output (Alt. Pin Configuration) C=Complementary Output G=Complementary Output and Enable/Disable (Alt. Pin Configuration) DUTY CYCLE 1=50% ±10%, 2=50% ±5% MECHANICAL DIMENSIONS PIN CONNECTIONS TABLE ALL DIMENSIONS IN MILLIMETERS SUGGESTED SOLDER PAD LAYOUT TAPE AND REEL DIMENSIONS ALL DIMENSIONS IN MILLIMETERS TAPE F 12 ±.1 A B C D E 24 ±.3 11.5 ±.1 10.75 ±.1 4 ±.2 2±.1 F M N O P Q 1.5 MIN 50 MIN 20.2 MIN 13±.2 40 MIN QTY/REEL 1000 REEL G H J K L R S T U V B0* 1.5 +.1-0 A0* .4 ±.05 K0* 2.5 MIN 10 MIN 30.4 MAX 360 MAX 24.4+2-0 *Compliant to EIA 481A ENVIRONMENTAL/MECHANICAL SPECIFICATIONS Characteristic MARKING SPECIFICATIONS Line 1: ECLIPTEK Specification OBSOLETE Seal Integrity Bubble test in Perfluorocarbon at +125°C ±5°C for 60 seconds minimum (internal crystal only). Solderability Sn63 Solder dip at +230°C ±5°C for 5 seconds/95% coverage. Marking Permanency 10 Strokes with brush after 1 minute soak in solvent, 3 times. Shock Random drop on hard wooden plate 3 times from a height of 20cm. Vibration Frequency with an amplitude of 1.5mm sweeping between 10Hz to 55Hz within 1 minute (approximately) for 2 hours minimum on each axis (X, Y and Z) for a total of 6 hours. Line 2: XX.XXX M Frequency in MHz (5 Digits Maximum + Decimal) Line 3: XX Y ZZ Week of Year Last Digit of Year Ecliptek Manufacturing Identifier MANUFACTURER CATEGORY SERIES PACKAGE VOLTAGE CLASS REV.DATE ECLIPTEK CORP. OSCILLATOR E13C2 CERAMIC 3.3V OS64 10/02 800-ECLIPTEK www.ecliptek.com for latest revision 159 Specifications subject to change without notice. E31C2 Series E31C2 • PECL Output VCXO • 5.0V supply voltage • 6 pad ceramic SMD package with J-leads • Stability to 20ppm • Output Enable/Disable available • Complementary Output available • Available on Tape and Reel H 5.1 L 14.2 W 9.85 OSCILLATOR ELECTRICAL SPECIFICATIONS Frequency Range 19.440MHz to 83.333MHz Operating Temperature Range 0°C to 70°C or -40°C to 85°C Storage Temperature Range Supply Voltage (VCC) Input Current OBSOLETE Logic Type -55°C to 125°C 5.0VDC ±5% 100mA Maximum 100KH Frequency Tolerance / Stability Inclusive of Operating Temp Range, Supply Voltage, ±50ppm, ±25ppm, or Load, and Aging @25°C over 10 years ±20ppm Maximum Output Voltage Logic High (VOH) VCC-1.025VDC Minimum Output Voltage Logic Low (VOL) VCC-1.620VDC Maximum Rise Time / Fall Time 20% to 80% of waveform 2 nSeconds Maximum Duty Cycle at 50% of waveform 50 ±10(%) 50 ±5(%) Load Drive Capability 50 Ohms into VCC-2.0VDC Additional Output / Logic Control No Connect and Single Output Enable/Disable and Single Output No Connect and Complementary Output or Enable/Disable and Complementary Output Enable/Disable Input Voltage VIL of VCC-1.475VDC Maximum Enables Output No Connection Enables Output VIH of VCC-1.165VDC Minimum Disables Output: Logic Low Disables Complementary Output: Logic High Start Up Time 10 mSeconds Maximum RMS Phase Jitter FJ = 12kHz to 20MHz Absolute Pull Range (APR) Inclusive of Operating Temp Range, Supply Voltage, ±50ppm Minimum 1 pSec Maximum Load, and Aging @25°C over 10 years Linearity 20%, 15%, or 10% Maximum Control Voltage (VC): Test Conditions for APR 2.5VDC ±2.0VDC Control Voltage Range (VCR) 0.0VDC to VCC Center Control Voltage 2.5VDC Transfer Function Positive Transfer Characteristic Input Impedance 50kOhms Typical Modulation Bandwidth 10kHz Minimum at -3dB with Control Voltage of +2.5VDC MANUFACTURER CATEGORY SERIES PACKAGE VOLTAGE CLASS REV.DATE ECLIPTEK CORP. OSCILLATOR E31C2 CERAMIC 5.0V OS68 10/02 800-ECLIPTEK www.ecliptek.com for latest revision 188 Specifications subject to change without notice. PART NUMBERING GUIDE E31C2 F 3 A 2 C - 77.760M TR FREQUENCY TOLERANCE & STABILITY/ OPERATING TEMPERATURE RANGE D=±50ppm Maximum over 0°C to +70°C E=±25ppm Maximum over 0°C to +70°C F=±20ppm Maximum over 0°C to +70°C H=±50ppm Maximum over -40°C to +85°C AVAILABLE OPTIONS Blank=Tubes TR = Tape and Reel (Standard) FREQUENCY ADDITIONAL OUTPUT/LOGIC CONTROL A=No Connect and Single Output B=Enable/Disable and Single Output C=No Connect and Complementary Output D=Enable/Disable and Complementary Output APR 3=±50ppm Minimum LINEARITY A=20% B=15% C=10% DUTY CYCLE 1=50 ±10(%), 2=50 ±5(%) MECHANICAL DIMENSIONS SUGGESTED SOLDER PAD LAYOUT ALL DIMENSIONS IN MILLIMETERS ALL DIMENSIONS IN MILLIMETERS Pin 1: Voltage Control Pin 2: Enable/Disable or No Connect Pin 3: Case Ground TAPE AND REEL DIMENSIONS Pin 4: Output Pin 5: Complementary Output or No Connect Pin 6: Supply Voltage Tolerances = ±0.1 ALL DIMENSIONS IN MILLIMETERS TAPE F 12 ±.1 A B C D E 24 ±.3 11.5 ±.1 10.75 ±.1 4 ±.2 2±.1 F M N O P Q 1.5 MIN 50 MIN 20.2 MIN 13±.2 40 MIN QTY/REEL 1000 REEL G H J K L R S T U V B0* 1.5 +.1-0 A0* .4 ±.05 K0* 2.5 MIN 10 MIN 30.4 MAX 360 MAX 24.4+2-0 *Compliant to EIA 481A ENVIRONMENTAL/MECHANICAL SPECIFICATIONS MARKING SPECIFICATIONS Characteristic Specification Line 1: ECLIPTEK Seal Integrity Bubble test in Perfluorocarbon at +125°C ±5°C for 60 seconds minimum (internal crystal only). Line 2: XX.XXX M Solderability Sn63 Solder dip at +230°C ±5°C for 5 seconds/95% coverage. Marking Permanency 10 Strokes with brush after 1 minute soak in solvent, 3 times. Shock Random drop on hard wooden plate 3 times from a height of 20cm. Vibration Frequency with an amplitude of 1.5mm sweeping between 10Hz to 55Hz within 1 minute (approximately) for 2 hours minimum on each axis (X, Y and Z) for a total of 6 hours. OBSOLETE Frequency in MHz (5 Digits Maximum + Decimal) Line 3: XX Y ZZ Week of Year Last Digit of Year Ecliptek Manufacturing Identifier MANUFACTURER CATEGORY SERIES PACKAGE VOLTAGE CLASS REV.DATE ECLIPTEK CORP. OSCILLATOR E31C2 CERAMIC 5.0V OS68 10/02 800-ECLIPTEK www.ecliptek.com for latest revision 189 Specifications subject to change without notice. E32C2 Series E32C2 • PECL Output VCXO • 3.3V supply voltage • 6 pad ceramic SMD package with J-leads • Stability to 20ppm • Output Enable/Disable available • Complementary Output available • Available on Tape and Reel H 5.1 L 14.2 W 9.85 OSCILLATOR ELECTRICAL SPECIFICATIONS Frequency Range 19.440MHz to 83.333MHz Operating Temperature Range Storage Temperature Range Supply Voltage (VCC) Input Current OBSOLETE Logic Type 0°C to 70°C or -40°C to 85°C -55°C to 125°C 3.3VDC ±5% 75mA Maximum 100KH Frequency Tolerance / Stability Inclusive of Operating Temp Range, Supply Voltage, ±50ppm, ±25ppm, or Load, and Aging @25°C over 10 years ±20ppm Maximum Output Voltage Logic High (VOH) VCC-1.025VDC Minimum Output Voltage Logic Low (VOL) VCC-1.620VDC Maximum Rise Time / Fall Time 20% to 80% of waveform 2 nSeconds Maximum Duty Cycle at 50% of waveform 50 ±10(%) 50 ±5(%) Load Drive Capability 50 Ohms into VCC-2.0VDC Additional Output / Logic Control No Connect and Single Output Enable/Disable and Single Output No Connect and Complementary Output or Enable/Disable and Complementary Output Enable/Disable Input Voltage VIL of VCC-1.475VDC Maximum Enables Output No Connection Enables Output VIH of VCC-1.165VDC Minimum Disables Output: Logic Low Disables Complementary Output: Logic High Start Up Time 10 mSeconds Maximum RMS Phase Jitter FJ = 12kHz to 20MHz Absolute Pull Range (APR) Inclusive of Operating Temp Range, Supply Voltage, ±50ppm Minimum 1 pSec Maximum Load, and Aging @25°C over 10 years Linearity 20%, 15%, or 10% Maximum Control Voltage (VC): Test Conditions for APR 1.65VDC ±1.35VDC Control Voltage Range (VCR) 0.0VDC to VCC Center Control Voltage 1.65VDC Transfer Function Positive Transfer Characteristic Input Impedance 50kOhms Typical Modulation Bandwidth 10kHz Minimum at -3dB with Control Voltage of +1.65VDC MANUFACTURER CATEGORY SERIES PACKAGE VOLTAGE CLASS REV.DATE ECLIPTEK CORP. OSCILLATOR E32C2 CERAMIC 3.3V OS67 10/02 800-ECLIPTEK www.ecliptek.com for latest revision 190 Specifications subject to change without notice. PART NUMBERING GUIDE E32C2 F 3 A 2 C - 77.760M TR FREQUENCY TOLERANCE & STABILITY/ OPERATING TEMPERATURE RANGE D=±50ppm Maximum over 0°C to +70°C E=±25ppm Maximum over 0°C to +70°C F=±20ppm Maximum over 0°C to +70°C H=±50ppm Maximum over -40°C to +85°C AVAILABLE OPTIONS Blank=Tubes TR = Tape and Reel (Standard) FREQUENCY ADDITIONAL OUTPUT/LOGIC CONTROL A=No Connect and Single Output B=Enable/Disable and Single Output C=No Connect and Complementary Output D=Enable/Disable and Complementary Output APR 3=±50ppm Minimum LINEARITY A=20% B=15% C=10% DUTY CYCLE 1=50 ±10(%), 2=50 ±5(%) MECHANICAL DIMENSIONS SUGGESTED SOLDER PAD LAYOUT ALL DIMENSIONS IN MILLIMETERS ALL DIMENSIONS IN MILLIMETERS Pin 1: Voltage Control Pin 2: Enable/Disable or No Connect Pin 3: Case Ground TAPE AND REEL DIMENSIONS Pin 4: Output Pin 5: Complementary Output or No Connect Pin 6: Supply Voltage Tolerances = ±0.1 ALL DIMENSIONS IN MILLIMETERS TAPE F 12 ±.1 A B C D E 24 ±.3 11.5 ±.1 10.75 ±.1 4 ±.2 2±.1 F M N O P Q 1.5 MIN 50 MIN 20.2 MIN 13±.2 40 MIN QTY/REEL 1000 REEL G H J K L R S T U V B0* 1.5 +.1-0 A0* .4 ±.05 K0* 2.5 MIN 10 MIN 30.4 MAX 360 MAX 24.4+2-0 *Compliant to EIA 481A ENVIRONMENTAL/MECHANICAL SPECIFICATIONS Characteristic MARKING SPECIFICATIONS Line 1: ECLIPTEK Specification OBSOLETE Seal Integrity Bubble test in Perfluorocarbon at +125°C ±5°C for 60 seconds minimum (internal crystal only). Solderability Sn63 Solder dip at +230°C ±5°C for 5 seconds/95% coverage. Marking Permanency 10 Strokes with brush after 1 minute soak in solvent, 3 times. Shock Random drop on hard wooden plate 3 times from a height of 20cm. Vibration Frequency with an amplitude of 1.5mm sweeping between 10Hz to 55Hz within 1 minute (approximately) for 2 hours minimum on each axis (X, Y and Z) for a total of 6 hours. Line 2: XX.XXX M Frequency in MHz (5 Digits Maximum + Decimal) Line 3: XX Y ZZ Week of Year Last Digit of Year Ecliptek Manufacturing Identifier MANUFACTURER CATEGORY SERIES PACKAGE VOLTAGE CLASS REV.DATE ECLIPTEK CORP. OSCILLATOR E32C2 CERAMIC 3.3V OS67 10/02 800-ECLIPTEK www.ecliptek.com for latest revision 191 Specifications subject to change without notice.