Ironwood GT-BGA-2004 Easily removable swivel socket lid Datasheet

GHz BGA Socket - Direct mount, solderless
Features
A
• Directly mounts to target PCB (needs tooling holes) with hardware
• High speed, reliable Elastomer connection
• Minimum real estate required
• Compression plate distributes forces evenly
• Ball guide prevents over compression of elastomer
• Easily removable swivel socket lid
50.000
Compression Plate
Socket Base
IC
A
GT Elastomer Contactor
Recommended Torque ~ 396 N-cm [35 lbf-in]
PROBE SLOT DETAIL
25.349
M5 HOLE
9.000
1.650
SECTION A-A
Description: GT-BGA 32x32 array 0.8mm pitch custom footprint
Primary dimension units are millimeters, Secondary dimension units are [inches], Weight is in grams.
Tolerances: Hole diameters ±0.0254mm [±0.001"], Pitches (from true position) ±0.0762mm [±0.003"], substrate thickness tolerance ±10%, all
other tolerances ±0.127mm [±0.005"] unless stated otherwise. Materials and specifications are subject to change without notice.
GT-BGA-2004 Drawing
Ironwood Electronics, Inc.
Tele: (800) 404-0204
www.ironwoodelectronics.com
Material: N/A
Finish: N/A
Weight: 78.24
STATUS: Released
SHEET: 1 OF 5
REV. A
ENG: B. Schatz
DRAWN BY: D. Hauer
SCALE: 3:2
FILE: GT-BGA-2004 Dwg
DATE: 5/27/14
8.00 (x4)
31x0.80=24.80 (x2)
0.80 typ
4X
1.600±0.025 THRU ALL
50.0
42.00
36.00±0.01
0.50 MIN (x715 Pads)
Socket Base Outline
34.00
4X
3.40±0.10 THRU ALL
1.0 X 45° (x4)
Target PCB Recommendations
Total thickness: 1.6mm min.
Plating: Gold or Solder Finish
PCB Pad Height: Same or higher than solder mask
Description: Recommended PCB Layout
Primary dimension units are millimeters, Secondary dimension units are [inches], Weight is in grams.
Tolerances: Hole diameters ±0.03mm [±0.001"], Pitches (from true position) ±0.025mm [±0.001"], substrate thickness tolerance ±10%, all
other tolerances ±0.13mm [±0.005"] unless stated otherwise. Materials and specifications are subject to change without notice.
GT-BGA-2004 Drawing
Ironwood Electronics, Inc.
Tele: (800) 404-0204
www.ironwoodelectronics.com
Material: N/A
Finish: N/A
Weight: 78.24
STATUS: Released
SHEET: 2 OF 5
REV. A
ENG: B. Schatz
DRAWN BY: D. Hauer
SCALE: 2:1
FILE: GT-BGA-2004 Dwg
DATE: 5/27/14
0.25 Z
0.25 Z
D
b
e
E
Z
A1
A
DIM
A
A1
b
D
E
e
Array
Dimensions are in millimeters.
1.
2.
3.
4.
Interpret dimensions and tolerances per ASME Y14.5M-1994.
Dimension b is measured at the maximum solder ball diameter, parallel to datum plane Z.
Datum Z (seating plane) is defined by the spherical crowns of the solder balls.
Parallelism measurement shall exclude any effect of mark on top surface of package.
MIN
0.3
0.35
26.8
26.8
Max Ball Count*
0.80
32 x32
MAX
2.5
0.5
0.55
27.2
27.2
1024
Description: Compatible Device
Primary dimension units are millimeters, Secondary dimension units are [inches], Weight is in grams.
Tolerances: Hole diameters ±0.03mm [±0.001"], Pitches (from true position) ±0.025mm [±0.001"], substrate thickness tolerance ±10%, all
other tolerances ±0.13mm [±0.005"] unless stated otherwise. Materials and specifications are subject to change without notice.
GT-BGA-2004 Drawing
Ironwood Electronics, Inc.
Tele: (800) 404-0204
www.ironwoodelectronics.com
Material: N/A
Finish: N/A
Weight: 78.24
STATUS: Released
SHEET: 3 OF 5
REV. A
ENG: B. Schatz
DRAWN BY: D. Hauer
SCALE: 2:1
FILE: GT-BGA-2004 Dwg
DATE: 5/27/14
1
2
3
ITEM
NO.
DESCRIPTION
Material
1
Compression Screw
Aluminum Alloy
2
Socket Lid
Aluminum Alloy
3
Compression Plate
Aluminum Alloy
4
IC Frame
Ultem
5
Test Chip
N/A
6
Shoulder Screw
Stainless Steel
7
Socket Base
Aluminum Alloy
8
Dowel Pin
Stainless Steel
9
IC Guide
Torlon 4203
10
Ball Guide
Kapton Polyimide/Cirlex
11
Mounting Screw
Stainless Steel
12
GT Elastomer
Conductive columns in
Kapton Polyimide
13
Target PCB
N/A
14
Backing Plate
Aluminum Alloy
4
5
6
11
7
8
9
10
13
12
14
Description: Exploded View
Primary dimension units are millimeters, Secondary dimension units are [inches], Weight is in grams.
Tolerances: Hole diameters ±0.03mm [±0.001"], Pitches (from true position) ±0.025mm [±0.001"], substrate thickness tolerance ±10%, all
other tolerances ±0.13mm [±0.005"] unless stated otherwise. Materials and specifications are subject to change without notice.
GT-BGA-2004 Drawing
Ironwood Electronics, Inc.
Tele: (800) 404-0204
www.ironwoodelectronics.com
Material: N/A
Finish: N/A
Weight: 78.24
STATUS: Released
SHEET: 4 OF 5
REV. A
ENG: B. Schatz
DRAWN BY: D. Hauer
SCALE: 2:1
FILE: GT-BGA-2004 Dwg
DATE: 5/27/14
SOCKET BASE
BACKING PLATE
COMPRESSION PLATE
6.000
2.5mm deeep cutout
for crystal
1.80
R1.0
2.00 (4x)
1.65
0.80
2.50
4X M5X0.8 THRU
Description: Base, Compression & Backing Pl
Primary dimension units are millimeters, Secondary dimension units are [inches], Weight is in grams.
Tolerances: Hole diameters ±0.03mm [±0.001"], Pitches (from true position) ±0.025mm [±0.001"], substrate thickness tolerance ±10%, all
other tolerances ±0.13mm [±0.005"] unless stated otherwise. Materials and specifications are subject to change without notice.
GT-BGA-2004 Drawing
Ironwood Electronics, Inc.
Tele: (800) 404-0204
www.ironwoodelectronics.com
Material: N/A
Finish: N/A
Weight: 78.24
STATUS: Released
SHEET: 5 OF 5
REV. A
ENG: B. Schatz
DRAWN BY: D. Hauer
SCALE: 3:2
FILE: GT-BGA-2004 Dwg
DATE: 5/27/14
Similar pages