FR601 THRU FR607 6.0 AMPS. Fast Recovery Rectifiers Voltage Range 50 to 1000 Volts Current 6.0 Amperes R-6 Features Low forward voltage drop High current capability High reliability High surge current capability Mechanical Data Cases: Molded plastic Epoxy: UL 94V-0 rate flame retardant Lead: Axial leads, solderable per MILSTD-202, Method 208 guaranteed Polarity: Color band denotes cathode end High temperature soldering guaranteed: 260℃/10 seconds/.375”,(9.5mm) lead lengths at 5 lbs.,(2.3kg) tension Weight: 1.65 grams Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol FR601 FR602 Type Number Maximum Recurrent Peak Reverse Voltage VRRM 50 100 Maximum RMS Voltage VRMS 35 70 Maximum DC Blocking Voltage VDC 50 100 Maximum Average Forward Rectified Current .375”(9.5mm) Lead Length @TA = 55℃ Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 6.0A Maximum DC Reverse Current @ TA=25℃ at Rated DC Blocking Voltage @ TA=100℃ Maximum Reverse Recovery Time ( Note 1 ) Typical Junction Capacitance ( Note 2 ) Typical Thermal Resistance ( Note 3 ) FR603 FR604 FR605 FR606 FR607 200 140 200 400 280 400 600 420 600 800 560 800 1000 700 1000 Units V V V I(AV) 6.0 A IFSM 200 A VF 1.2 V IR 10 200 uA uA nS pF O C/W ℃ ℃ Trr 150 250 Cj 80 30 RθJA Operating Temperature Range TJ -65 to +150 Storage Temperature Range TSTG -65 to +150 Notes:1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1 MHz and Applied Reverse Voltage of 4..0 Volts D.C. 3. Mount on Cu-Pad Size 16mm x 16mm on P.C.B. - 416 - 500 RATINGS AND CHARACTERISTIC CURVES (FR601 THRU FR607) FIG.2- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 300 PEAK FORWARD SURGE CURRENT. (A) AVERAGE FORWARD CURRENT AMPERES FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE 8 6 4 Single Phase Half Wave 60Hz Resistive or Inductive Load 0.375"(9.5mm) Lead Length 2 0 0 25 50 75 100 125 150 250 200 8.3ms Single Half Sine Wave JEDEC Method 150 100 50 0 175 1 5 10 50 100 o AMBIENT TEMPERATURE. ( C) NUMBER OF CYCLES AT 60Hz FIG.3- TYPICAL FORWARD CHARACTERISTICS FIG.4- TYPICAL JUNCTION CAPACITANCE 1000 700 600 500 JUNCTION CAPACITANCE.(pF) INSTANTANEOUS FORWARD CURRENT. (A) 500 100 40 10 Tj=25oC Pulse Width=300 s 1% Duty Cycle 400 300 200 100 60 40 1 2 4 0.1 0.6 6 10 20 REVERSE VOLTAGE. (V) 1 0.8 1.0 1.2 1.4 1.6 1.8 2.0 FORWARD VOLTAGE. (V) FIG.5- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50W NONINDUCTIVE 10W NONINDUCTIVE trr +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) 0 -0.25A (+) NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms - 417 - -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm 40 60 100