LM49155 www.ti.com SNAS492 – JULY 2010 LM49155 PRODUCT BRIEF Uplink Noise Suppression & Downlink SNR Enhancement Analog Audio Subsystem Check for Samples: LM49155 FEATURES 1 • 2 • • Noise cancellation for uplink and downlink without DSP-type artifacts, distortions or delays Adapting AGC on ambient noise level & downlink signal strength for earpiece Downlink adjustable noise-reducing high pass filter • • • E2S Class D Amplifier with ALC Ground Referenced Headphone Outputs with Advanced Click Pop Suppression Micro-power shutdown APPLICATIONS • • Mobile Phones Portable Electronic Devices DESCRIPTION The LM49155 is a fully integrated audio subsystem designed for portable handheld applications such as cellular phones. The LM49155 combines a Noise Suppression microphone amplifier, a 1.35W mono class D amplifier with ALC, class AB earpiece driver with AGC, a high efficiency, stereo, ground referenced headphone amplifier with click pop suppression and I2C modes select and volume control. The LM49155 features analog fully differential input, and differential output microphone amplifier designed to reduce background acoustic noise, while delivering superb speech clarity in voice communication applications. Downlink SNR enhancement with an advanced acoustic AGC technology to adjust output levels. The LM49155 speaker amplifier features National’s unique output limiter that provides both a no-clip feature and speaker protection. The E2S class D amplifier features a patented, ultra low EMI PWM architecture that significantly reduces RF emissions while preserving audio quality and efficiency. The headphone drivers feature National’s ground referenced architecture that creates a ground-referenced output from a single, low-voltage supply. The LM49155 is available in an ultra-small 36-bump micro SMD package (3.434mm x 3.459mm x 0.6mm). Notice: This document is not a full datasheet. For more information regarding this product or to order samples please contact your local National Semiconductor sales office or visit http://www.national.com/support/dir.html These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Table 1. Key Specifications Uplink Far Field Noise Suppression Electrical FFNSE at f = 1kHz Downlink SNR Enhancement Earpiece Amplifier VALUE UNIT 34 dB (typ) Near-Field SNR Enhancement 6 to 18 Downlink SNRIE 16 dB (typ) Class D Loudspeaker Amplifier RL = 15μH+8Ω+15μH POUT, THD+N ≤ %, VDD = 5.0V 1.35 W (typ) Headphone Amplifier RL = 32Ω POUT, THD+N ≤ %, HPVDD = 1.8V 19 mW (typ) 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2010, Texas Instruments Incorporated LM49155 SNAS492 – JULY 2010 www.ti.com Simplified Block Diagram UPLINK NOISE SUPPRESSION COMMUNICATIONS PROCESSOR SNR ENHANCER AGC EARPIECE AMPLIFIER MONO VOLUME MIXER ALC STEREO VOLUME 2 Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Links: LM49155 LM49155 www.ti.com SNAS492 – JULY 2010 Typical Application 2.7V to 5.5V CS1 1 µF 2.7V to 5.5V CS2 1 µF VDD LSVDD 4.7 µF CT1 MIC_BIAS VOLTAGE 4.7 µF CT2 CT3 4.7 µF Ci1 PRE-AMP 470 nF MIC1+ DCAP MIC1- ANALOG UPLINK/ DOWNLINK NOISE CANCELLING PROCESSOR and SNR ENHANCER Ci2 470 nF Ci3 470 nF MIC2+ MIC2Ci4 470 nF POST-AMP 4.7 µF LPF+ CLP1 MICOUT+ MICOUT- To Uplink Signal Path CLP2 6 dB/12 dB 12 dB to 36 dB LPF- AGC AMP MIC_GND EPOUT+ OUTPUT POWER LIMITER EPOUT- Ci5 68 nF INM + Audio Differential Input INM - VOLUME -80 dB to +18 dB Ci6 68 nF INL Audio Single-Ended Inputs Ci7 0.22 µF Class D +12 dB, +18 dB AUTOMATIC LEVEL CONTROL -6 dB Mixer and Output Mode VOLUME -80 dB to +18 dB Ci8 0.22 µF BYPASS CB 2.2 µF LSOUTSET CSET 0.1 µF -18 dB to 0 dB INR LSOUT+ VOLUME -80 dB to +18 dB RSET (Optional) HPL -18 dB to 0 dB HPR 1.7V to 2.7V BIAS HPVDD CS3 1 µF 2 I CVDD SDA SCL CHARGE PUMP I2C INTERFACE MIC_GND GND CPVSS CIP CIN CPGND 2.2 µF C1 2.2 µF Figure 1. Typical Application Circuit Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Links: LM49155 3 LM49155 SNAS492 – JULY 2010 www.ti.com Connection Diagrams TL Package (3.434mm x 3.459mm x 0.6mm) Top View 6 5 4 3 2 1 A B C D E F Figure 2. Top View (Bump Side Down) spacer spacer 36 Bump micro SMD Marking XXYY GN7 Bump A1 Figure 3. Top View XX — Date Code YY — Die Traceability G — Boomer N7 — LM49155TL 4 Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Links: LM49155 PACKAGE OPTION ADDENDUM www.ti.com 26-Nov-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) LM49155TL/NOPB NRND DSBGA YZR 36 250 Green (RoHS & no Sb/Br) SNAGCU Level-1-260C-UNLIM GN7 LM49155TLX/NOPB NRND DSBGA YZR 36 1000 Green (RoHS & no Sb/Br) SNAGCU Level-1-260C-UNLIM GN7 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 26-Nov-2013 In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 21-Mar-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) LM49155TL/NOPB DSBGA YZR 36 250 178.0 12.4 LM49155TLX/NOPB DSBGA YZR 36 1000 178.0 12.4 Pack Materials-Page 1 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 3.63 3.63 0.76 8.0 12.0 Q1 3.63 3.63 0.76 8.0 12.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 21-Mar-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM49155TL/NOPB DSBGA YZR LM49155TLX/NOPB DSBGA YZR 36 250 210.0 185.0 35.0 36 1000 210.0 185.0 35.0 Pack Materials-Page 2 MECHANICAL DATA YZR0036xxx D 0.600±0.075 E TLA36XXX (Rev D) D: Max = 3.489 mm, Min =3.429 mm E: Max = 3.465 mm, Min =3.405 mm 4215058/A NOTES: A. All linear dimensions are in millimeters. Dimensioning and tolerancing per ASME Y14.5M-1994. B. This drawing is subject to change without notice. www.ti.com 12/12 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2015, Texas Instruments Incorporated