Coils/Inductors/Microchip Transformer > Chip Coils > for High Frequency Monolithic Type Data Sheet Chip Coils 1 for High Frequency Monolithic Type LQG18H Series (0603 Size) ■ Dimension ■ Packaging 0.3±0.2 Code Packaging Minimum Quantity D 180mm Paper Tape 4000 J 330mm Paper Tape 10000 B Bulk(Bag) 1000 0.8±0.15 Polarity Marking 1.6±0.15 0.8±0.15 (in mm) ■ Rated Value (p: packaging code) Part Number Inductance Test Frequency Rated Current Max. of DC Resistance Q (min.) Test Frequency Self Resonance Frequency (min.) LQG18HN1N2S00p 1.2nH±0.3nH 100MHz 500mA 0.10ohm 12 100MHz 6000MHz LQG18HN1N5S00p 1.5nH±0.3nH 100MHz 500mA 0.10ohm 12 100MHz 6000MHz LQG18HN1N8S00p 1.8nH±0.3nH 100MHz 500mA 0.10ohm 12 100MHz 6000MHz LQG18HN2N2S00p 2.2nH±0.3nH 100MHz 500mA 0.10ohm 12 100MHz 6000MHz LQG18HN2N7S00p 2.7nH±0.3nH 100MHz 500mA 0.15ohm 12 100MHz 6000MHz LQG18HN3N3S00p 3.3nH±0.3nH 100MHz 500mA 0.15ohm 12 100MHz 6000MHz LQG18HN3N9S00p 3.9nH±0.3nH 100MHz 450mA 0.15ohm 12 100MHz 6000MHz LQG18HN4N7S00p 4.7nH±0.3nH 100MHz 450mA 0.20ohm 12 100MHz 6000MHz LQG18HN5N6S00p 5.6nH±0.3nH 100MHz 430mA 0.20ohm 12 100MHz 5000MHz LQG18HN6N8J00p 6.8nH±5% 100MHz 430mA 0.25ohm 12 100MHz 5000MHz LQG18HN8N2J00p 8.2nH±5% 100MHz 400mA 0.25ohm 12 100MHz 4000MHz LQG18HN10NJ00p 10nH±5% 100MHz 400mA 0.30ohm 12 100MHz 3500MHz LQG18HN12NJ00p 12nH±5% 100MHz 400mA 0.35ohm 12 100MHz 3000MHz LQG18HN15NJ00p 15nH±5% 100MHz 350mA 0.40ohm 12 100MHz 2800MHz LQG18HN18NJ00p 18nH±5% 100MHz 350mA 0.45ohm 12 100MHz 2600MHz LQG18HN22NJ00p 22nH±5% 100MHz 300mA 0.50ohm 12 100MHz 2300MHz LQG18HN27NJ00p 27nH±5% 100MHz 300mA 0.55ohm 12 100MHz 2000MHz LQG18HN33NJ00p 33nH±5% 100MHz 300mA 0.60ohm 12 100MHz 1700MHz LQG18HN39NJ00p 39nH±5% 100MHz 300mA 0.65ohm 12 100MHz 1500MHz LQG18HN47NJ00p 47nH±5% 100MHz 300mA 0.70ohm 12 100MHz 1200MHz LQG18HN56NJ00p 56nH±5% 100MHz 300mA 0.75ohm 12 100MHz 1100MHz LQG18HN68NJ00p 68nH±5% 100MHz 300mA 0.80ohm 12 100MHz 1000MHz LQG18HN82NJ00p 82nH±5% 100MHz 300mA 0.85ohm 12 100MHz 900MHz Operating Temperature Range: -40°C to +85°C Only for reflow soldering. Continued on the following page. o This data sheet is applied for CHIP COIL used for General Electronics equipment for your design. ! Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2007.9.6 http://www.murata.com/ Coils/Inductors/Microchip Transformer > Chip Coils > for High Frequency Monolithic Type Data Sheet 2 Continued from the preceding page. Part Number LQG18HNR10J00p Inductance Test Frequency Rated Current 100nH±5% 100MHz 300mA Max. of DC Resistance Q (min.) Test Frequency 0.90ohm 12 Self Resonance Frequency (min.) 100MHz 800MHz Operating Temperature Range: -40°C to +85°C Only for reflow soldering. ■ Q - Frequency Characteristics (Typ.) ■ Inductance - Frequency Characteristics (Typ.) 1000 200 68nH 160 Inductance (nH) 3.3nH Q 120 80 10nH 100 10 10nH 40 3.3nH 68nH 0 100 1000 1 100 10000 Frequency (MHz) 1000 10000 Frequency (MHz) ■ !Caution/Notice !Caution (Rating) Do not use products beyond the rated current as this may create excessive heat. Notice Solderability of Tin plating termination chip might be deteriorated when low temperature soldering profile where peak solder temperature is below the Tin melting point is used. Please confirm the solderability of Tin plating termination chip before use. o This data sheet is applied for CHIP COIL used for General Electronics equipment for your design. ! Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2007.9.6 http://www.murata.com/