Preset counters electronic 2 presets, totalizer and batch counter Display LED, 5-digits, programmable NE216 Features –– Preset counter with two presets –– Display 5-digits –– Totalizer, hour counter –– Operating mode, start count, scaling factor programmable –– Connection: Incremental encoder or digital sensors –– Step and trailing preset programmable –– Interface RS485 Technical data - electrical ratings Voltage supply 22...50 VAC (50/60 Hz) 85...265 VAC (50/60 Hz) 12...30 VDC Programmable parameters Power consumption 5 VA, 5 W Sensor supply AC: 24 VDC ±20 % / 100 mA DC: 9...28 VDC / 100 mA Operating modes Sensor logic Scaling factor Count mode Control inputs Approvals UL/cUL, CE conform Display LED, 7-segment display Number of digits 5-digits Technical data - mechanical design Digit height 7.6 mm Operating temperature 0...+50 °C Function Preset counter Main counter with 2 presets Totalizer Hour counter Storing temperature -20...+70 °C Relative humidity 80 % non-condensing E-connection Plug-in screw terminals Core cross-section 1.5 mm² Protection DIN EN 60529 IP 65 face with seal Operation / keypad Membrane with softkeys Housing type Built-in housing Dimensions W x H x L 48 x 48 x 100 mm 100 mm Scaling factor 0.0001...9999.99 Count modes Adding or subtracting A-B (difference counting) A+B total (parallel counting) Up/Down A 90° B phase evaluation Counting frequency 3 Hz, 25 Hz, 10 kHz programmable Installation depth Mounting Clip frame Operating modes Step preset, Trailing preset, Time meter and hour counter Cutout dimensions 45 x 45 mm (+0.6) Materials Housing: Makrolon 6485 (PC) Keypad: Polyester Weight approx. 150 g Data memory >10 years in EEPROM Reset Button, electric or automatic Outputs electronic Optocoupler Outputs relay Normally open or closed, programmable Output holding time 0.01...99.99 s Interface RS485 Standard DIN EN 61010‑1 Protection class II Overvoltage category II Pollution degree 2 Emitted interference DIN EN 61000-6-4 Interference immunity DIN EN 61000-6-2 1 www.baumerivo.com 30/10/2008 Technical data - electrical ratings Subject to modification in technic and design. Errors and omissions excepted. NE216 - LED Preset counter Preset counters electronic 2 presets, totalizer and batch counter Display LED, 5-digits, programmable NE216 Part number Block circuit diagram AX01 12 Sensor supply + 13 - Voltage supply Voltage supply 1 22...50 VAC 2 85...265 VAC 3 12...30 VDC - 1 + 2 Totalizer Signal input A 7 B 8 Control input 1 9 2 10 Outputs 1 Relay outputs 2 Electronic outputs A 90° B T,R- 14 T,R+ 15 Interface 0 Without interface 1 RS485 Output Main counter with 2 presets start count scaling factor 3 4 5 Operating time meter 6 P1 P2 Interface RS485 Trigger level Input circuit Accessories PNP- / NPN- / AC-logic Input level Programmable Adaptor plates (page %S) Input level Low 0...2 VDC Z 118.033 Input level High 3...40 VDC Input resistance 3 kΩ Relay outputs Output circuit Switching voltage max. 250 VAC / 110 VDC Switching current max. 1A Switching capacity max. 150 VA / 30 W Relay responding time 5 ms Electronical outputs Output circuit Optocoupler short-circuit proof Switching voltage max. 40 V Switching current max. 25 mA Residual voltage <1 V Adaptor plate for screw mount, face 60 x 75 mm Z 118.034 Adaptor plate for clip mount, face 53.2 x 53.2 mm Z 118.035 Adaptor plate for clip mount, face 60 x 75 mm Connection diagram Electronic outputs 5 4 3 2 1 RS485 Sensor supply 6 5 Control input 4 3 max. 265 V terminal - terminal / A 7 Signal input 2 1 P2 P1 Outputs - terminal 8 B 9 2 3 0V +24V T,R- T,R+ A 1 Signal input P2 P1 Outputs max. 265 V terminal - terminal/ 15 14 13 12 11 10 Supply voltage 6 7 Supply voltage RS485 Sensor- Control supply input 8 B 9 2 3 0V +24V T,R- T,R+ 15 14 13 12 11 10 1 Relay outputs Subject to modification in technic and design. Errors and omissions excepted. Comparator inputs Inputs - terminal Dimensions 100 60.8 48 7 1-6 44.7 48 10 2 www.baumerivo.com 30/10/2008 NE216.