Film Capacitors – Power Factor Correction Key components – Terminal to RJ45 converter Series/Type: Ordering code: B44066 B44066R1*11E230 Date: Version: November 2009 1 EPCOS AG 2009. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. Film Capacitors – Power Factor Correction Key components – Terminal to RJ45 converter B44066R1*11E230 B44066 Preliminary data Characteristics RJ45 – converter 1xRJ45-BR6000 2xRJ45-BR6000 2xRJ45-MMI6000 Terminal to RJ45 converter To connect the interface terminal of BR6000, BR7000 or MMI6000 via RJ45-standard cable (1:1) Connection of several devices at the RS485 bus with simple connection (one click) Example: ● Connection of several BR6000 or BR7000 to a PC with BR7000-SOFT ● Coupling of several BR6000 with each other ● Coupling of BR6000 or BR7000 with MMI6000 1xRJ45 for BR6000/BR7000 2xRJ45 for BR6000/BR7000 2xRJ45 for MMI6000 Technical data and specifications Design Compact form Dimensions w × h × l 35 x 15 x 30 mm Weight Approx. 0.1 kg Power supply None (passive cable adapter) Variants 1xRJ45-BR6000 4-pole interface-terminal BR6000/BR7000 to 1xRJ45 jack 2xRJ45-BR6000 4-pole interface-terminal BR6000/BR7000 to 2xRJ45 jack (in parallel) 2xRJ45-MMI6000 4-pole interface-terminal MMI6000 to 2xRJ45 jack Protection class (IEC 60529) IP00 Ambient and storage temperature -20 … +60 °C Ordering codes 1xRJ45 for BR6000/BR7000 B44066R1611E230 2xRJ45 for BR6000/BR7000 B44066R1711E230 2xRJ45 for MMI6000 B44066R1811E230 FK PC PM PFC Please read Cautions and warnings and Important notes at the end of this document. November 2009 Page 2 of 4 Film Capacitors – Power Factor Correction Key components – Terminal to RJ45 converter B44066R1*11E230 B44066 Preliminary data Example: Coupling of several BR6000 for connection to a PC Easy installation by using adapters CV-RJ45, converter CV-USB485 and standard LAN-Patch-Cable (1:1) Example: Connection of several BR6000/ BR7000 to a PC (visualization) Using 3 additional MMI6000 connected with a BR7000 via adapters CV-RJ45 and standard LAN-Patch-Cable (1.1) Example: External current-measuring - for direct measuring of the current in individual cabinets - for current measuring in case current transformers are located far away Note: These RJ45 adapters support a RJ485-interface with internal MODBUS protocol. It is not a LAN-interface! FK PC PM PFC Please read Cautions and warnings and Important notes at the end of this document. November 2009 Page 3 of 4 Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. The aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms of Delivery for Products and Services in the Electrical Industry” published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSMP, CSSP, CTVS, DeltaCap, DSSP, MiniBlue, MiniCell, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks. Page 4 of 4