SURFACE MOUNT SUPER FAST RECTIFIER ES2A THRU ES2J VOLTAGE RANGE 50 to 600Volts CURRENT 2.0 Ampere FEATURES • • • • • DO-214AA(SMB) Plastic package has Underwrites Laboratory Flammability Classification 94V-0 Glass passivated chip junction Built-in strain relief Super Fast switching speed for high efficiency High temperature soldering guaranteed: 250℃/10 seconds MECHANICAL DATA • • • • Case: JEDED DO-214AA transfer molded plastic Terminals: Solder plated, Solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Weight: 0.003 ounce, 0.093 gram Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS • • • Ratings at 25℃ ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load derate current by 20%. SYMBOLS ES2A ES2B Maximum Repetitive Peak Reverse Voltage VRRM 50 100 Maximum RMS Voltage VRMS 35 70 Maximum DC Blocking Voltage VDC 50 100 Maximum Average Forward Rectified Current at TL =100℃ Peak Forward Surge Current 8.3ms single half sine wave superimposed on rated load (JEDEC method) Maximum lnstantaneous Forward Voltage @ 2.0A Maximum DC Reverse Current at TA=25℃ rated DC Blocking voltage per TA=125℃ element Maximum Reverse Recovery Time Test conditions IF=0.5A, IR=1.0A, IRR=0.25A Typical Junstion Capacitance (Measured at 1.0MHz and applied reverse voltage of 4.0V) Typical Thermal Resistance (Note 1) ES2C 150 105 150 ES2D 200 140 200 ES2E 300 210 300 ES2G 400 280 400 ES2J 600 420 600 UNIT Volts Volts Volts I(AV) 2.0 Amps IFSM 50 Amps VF 0.95 IR trr CJ RθJA RθJL TJ TSTG 1.25 5.0 200 35 25 75 17 (-55 to +150) (-55 to +150) Web Site: www.cnmic.com Volts µA nS 208 Operating Junction Temperature Range Storage Tempetature Rang Notes: 1. Thermal resistance from Junction to ambient and from junction to lead mounted on P.C.B. with 0.3”×0.3”(8.0mm × 8.0mm) copper pad areas. E-mail: [email protected] 1.7 pF ℃/W ℃ ℃ SURFACE MOUNT SUPER FAST RECTIFIER ES2A THRU ES2J VOLTAGE RANGE 50 to 600 Volts CURRENT 2.0 Ampere FIG.1-TYPICAL FORWARD CURRENT FIG.2-MAXIMUM NON-REPETITIVE PEAK DERATING CURVE FORWARD SURGE CURRENT PEAK FORWARD SURGE 3.0 1.0 Single Phase Half Wave 60Hz Resistive or Inductive Load 0.375″(9.5mm) Lead Length 60 CURRENT, (A) 2.0 (A) AVERAGE FORWARD CURRENT, RATING AND CHRACTERISTIC CURVES ES2A THRU ES2J 8.3ms Single Half Sine-Wave (JEDEC Method) TJ = T jmax 50 40 30 20 10 1 Cycle 0 0 25 100 75 50 125 175 150 0 1 4 2 AMBIENT TEMPERATURE, (° C) 6 8 10 40 20 60 100 NUMBER OF CYCLES AT 60 Hz FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG.4-TYPICAL REVERSE CHARACTERISTICS 0.1 0.01 TJ=25° C Pulse Width=300us 1% Duty Cycle 10 1.0 (μA) INSTANTANEOUS REVERSE CURRENT, 2E ES ES 2J ES 2A -2D -2G 1.0 (A) INSTANTANEOUS FORWARD CURRENT, 10 TJ =100° C 0.1 TJ =25℃ 0.01 0 0.001 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 20 40 60 80 120 100 140 PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) INSTANTANEOUS FORWARD VOLTAGE,(V) FIG.5-TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE,(pF) 100 ES 2A-E S2D ES2E-ES 2J F1G.6-TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC Trr 50Ω 10Ω NONINDUCTIVE NONINDUCTIVE +0.5A (-) 10 (+) 25 Vdc (approx.) (-) TJ =25° C f=1MHz Vsig=50mVp-p 1Ω NON INDUCTIVE PULSE GENERATIOR (NOTE 2) 0 -0.25A (+) OSCILLOSCOPE (NOTE 1) -1.0A 1 0.1 D.U.T. 1.0 10 100 REVERSE VOLTAGE,(V) E-mail: [email protected] NOTES : 1.Rise Time=7ns max. Input Impedance= 1 magohm. 22pF 2.Rise time=10ns max. Source Impedance= 50 ohms Web Site: www.cnmic.com 1cm SET TIME BASE FOR 50/100ns/cm