Am29LV065MU Data Sheet RETIRED PRODUCT This product has been retired and is not available for designs. For new and current designs, S29GL064A supersedes Am29LV065MU and is the factory-recommended migration path. Please refer to the S29GL064A datasheet for specifications and ordering information. Availability of this document is retained for reference and historical purposes only. The following document contains information on Spansion memory products. Continuity of Specifications There is no change to this data sheet as a result of offering the device as a Spansion product. Any changes that have been made are the result of normal data sheet improvement and are noted in the document revision summary. For More Information Please contact your local sales office for additional information about Spansion memory solutions. Publication Number 25262 Revision C Amendment 4 Issue Date September 12, 2006 THIS PAGE LEFT INTENTIONALLY BLANK. DATA SHEET Am29LV065MU 64 Megabit (8 M x 8-Bit) MirrorBit™ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O™ Control This product has been retired and is not available for designs. For new and current designs, S29GL064A supersedes Am29LV065MU and is the factory-recommended migration path. Please refer to the S29GL064A datasheet for specifications and ordering information. Availability of this document is retained for reference and historical purposes only. DISTINCTIVE CHARACTERISTICS ARCHITECTURAL ADVANTAGES Single power supply operation — 3 volt read, erase, and program operations VersatileI/O™ control — Device generates and tolerates data voltages on CE# and DQ inputs/outputs as determined by the voltage on the VIO pin; operates from 1.65 to 3.6 V Manufactured on 0.23 µm MirrorBit process technology SecSi™ (Secured Silicon) Sector region — 256-byte sector for permanent, secure identification through an 16-byte random Electronic Serial Number, accessible through a command sequence — May be programmed and locked at the factory or by the customer Flexible sector architecture — One hundred twenty-eight 64 Kbyte sectors Compatibility with JEDEC standards — Provides pinout and software compatibility for single-power supply flash, and superior inadvertent write protection Minimum 100,000 erase cycle guarantee per sector 20-year data retention at 125°C PERFORMANCE CHARACTERISTICS High performance — 90 ns access time — 25 ns page read times — 0.5 s typical sector erase time — 11 µs typical effective write buffer byte programming time: 32-byte write buffer reduces overall programming time for multiple-byte updates — 8-byte read page buffer — 32-byte write buffer Low power consumption (typical values at 3.0 V, 5 MHz) — 30 mA typical active read current — 50 mA typical erase/program current — 1 µA typical standby mode current Package options — 48-pin TSOP — 63-ball FBGA SOFTWARE & HARDWARE FEATURES Software features — Program Suspend & Resume: read other sectors before programming operation is completed — Erase Suspend & Resume: read/program other sectors before an erase operation is completed — Data# polling & toggle bits provide status — Unlock Bypass Program command reduces overall multiple-byte programming time — CFI (Common Flash Interface) compliant: allows host system to identify and accommodate multiple flash devices Hardware features — Sector Group Protection: hardware method of preventing write operations within a sector group — Temporary Sector Unprotect: VID-level method of changing code in locked sectors — ACC (high voltage) pin accelerates programming time for higher throughput during system production — Hardware reset pin (RESET#) resets device — Ready/Busy# pin (RY/BY#) detects program or erase cycle completion This Data Sheet states AMD’s current technical specifications regarding the Products described herein. This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. Publication# 25262 Rev: C Amendment/4 Issue Date: September 12, 2006 Refer to AMD’s Website (www.amd.com) for the latest information. D A T A S H E E T GENERAL DESCRIPTION The Am29LV065MU is a 64 Mbit, 3.0 volt single power supply flash memory devices organized as 8,388,608 bytes. The device has an 8-bit wide data bus, and can be programmed either in the host system or in standard EPROM programmers. An access time of 90, 100, 110, or 120 ns is available. Note that each device has a specific operating voltage range (VCC) and an I/O voltage range (VIO), as specified in “Product Selector Guide” on page 5 and “Ordering Information” on page 9. The device is offered in a 48-pin TSOP or 63-ball FBGA package. Each device has separate chip enable (CE#), write enable (WE#) and output enable (OE#) controls. Each device requires only a single 3.0 volt power supply for both read and write functions. In addition to a V CC input, a high-voltage accelerated program (ACC) input provides shorter programming times through increased current. This feature is intended to facilitate factory throughput during system production, but may also be used in the field if desired. The device is entirely command set compatible with the JEDEC single-power-supply Flash standard. Commands are written to the device using standard microprocessor write timing. Write cycles also internally latch addresses and data needed for the programming and erase operations. The sector erase architecture allows memory sectors to be erased and reprogrammed without affecting the data contents of other sectors. The device is fully erased when shipped from the factory. Device programming and erasure are initiated through command sequences. Once a program or erase operation has begun, the host system need only poll the DQ7 (Data# Polling) or DQ6 (toggle) status bits or monitor the Ready/Busy# (RY/BY#) output to determine whether the operation is complete. To facilitate programming, an Unlock Bypass mode reduces command sequence overhead by requiring only two write cycles to program data instead of four. and tolerates on the CE# control input and DQ I/Os to the same voltage level that is asserted on the VIO pin. See “Ordering Information” on page 9. for valid VIO options. Hardware data protection measures include a low VCC detector that automatically inhibits write operations during power transitions. The hardware sector protection feature disables both program and erase operations in any combination of sectors of memory. This can be achieved in-system or via programming equipment. The Erase Suspend/Erase Resume feature allows the host system to pause an erase operation in a given sector to read or program any other sector and then complete the erase operation. The Program Suspend/Program Resume feature enables the host system to pause a program operation in a given sector to read any other sector and then complete the program operation. The hardware RESET# pin terminates any operation in progress and resets the device, after which it is then ready for a new operation. The RESET# pin may be tied to the system reset circuitry. A system reset would thus also reset the device, enabling the host system to read boot-up firmware from the Flash memory device. The device reduces power consumption in the standby mode when it detects specific voltage levels on CE# and RESET#, or when addresses have been stable for a specified period of time. The SecSi™ (Secured Silicon) Sector provides a 256 byte area for code or data that can be permanently protected. Once this sector is protected, no further changes within the sector can occur. AMD MirrorBit flash technology combines years of Flash memory manufacturing experience to produce the highest levels of quality, reliability and cost effectiveness. The device electrically erases all bits within a sector simultaneously via hot-hole assisted erase. The data is programmed using hot electron injection. The VersatileI/O™ (VIO) control allows the host system to set the voltage levels that the device generates 2 Am29LV065MU September 12, 2006 D A T A S H E E T MIRRORBIT 64 MBIT DEVICE FAMILY Bus Sector Architecture Packages VIO RY/BY# WP#, ACC WP# Protection x8 Uniform (64 Kbyte) 48-pin TSOP (std. & rev. pinout), 63-ball FBGA Yes Yes ACC only No WP# LV640MT/B x8/x16 Boot (8 x 8 Kbyte at top & bottom) 48-pin TSOP, 63-ball Fine-pitch BGA, 64-ball Fortified BGA No Yes WP#/ACC pin 2 x 8 Kbyte top or bottom LV640MH/L x8/x16 Uniform (64 Kbyte) 56-pin TSOP (std. & rev. pinout), 64 Fortified BGA Yes Yes WP#/ACC pin 1 x 64 Kbyte high or low LV641MH/L x16 Uniform (32 Kword) 48-pin TSOP (std. & rev. pinout) Yes No Separate WP# and ACC pins 1 x 32 Kword top or bottom LV640MU x16 Uniform (32 Kword) 63-ball Fine-pitch BGA, 64-ball Fortified BGA Yes Yes ACC only No WP# Device LV065MU RELATED DOCUMENTS To download related documents, click on the following links or go to www.amd.com→Flash Memory→Product Information→MirrorBit→Flash Information→Technical Documentation. MirrorBit™ Flash Memory Write Buffer Programming and Page Buffer Read September 12, 2006 Implementing a Common Layout for AMD MirrorBit and Intel StrataFlash Memory Devices Migrating from Single-byte to Three-byte Device IDs AMD MirrorBit™ White Paper Am29LV065MU 3 D A T A S H E E T TABLE OF CONTENTS Product Selector Guide . . . . . . . . . . . . . . . . . . . . . 5 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Connection Diagrams . . . . . . . . . . . . . . . . . . . . . . 6 Pin Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Logic Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Ordering Information . . . . . . . . . . . . . . . . . . . . . . . 9 Device Bus Operations . . . . . . . . . . . . . . . . . . . . 10 Table 1. Device Bus Operations .....................................................10 VersatileIO™ (VIO) Control ..................................................... 10 Requirements for Reading Array Data ................................... 10 Page Mode Read .................................................................... 11 Writing Commands/Command Sequences ............................ 11 Write Buffer ............................................................................. 11 Accelerated Program Operation ............................................. 11 Autoselect Functions .............................................................. 11 Standby Mode ........................................................................ 11 Automatic Sleep Mode ........................................................... 11 RESET#: Hardware Reset Pin ............................................... 12 Output Disable Mode .............................................................. 12 Table 2. Sector Address Table ........................................................13 Autoselect Mode..................................................................... 17 Table 3. Autoselect Codes, (High Voltage Method) .......................17 Sector Group Protection and Unprotection ............................. 18 Write Operation Status . . . . . . . . . . . . . . . . . . . . . 35 DQ7: Data# Polling ................................................................. 35 Figure 8. Data# Polling Algorithm .................................................. 35 RY/BY#: Ready/Busy#............................................................ 36 DQ6: Toggle Bit I .................................................................... 36 Figure 9. Toggle Bit Algorithm........................................................ 36 DQ2: Toggle Bit II ................................................................... 37 Reading Toggle Bits DQ6/DQ2 ............................................... 37 DQ5: Exceeded Timing Limits ................................................ 37 DQ3: Sector Erase Timer ....................................................... 37 DQ1: Write-to-Buffer Abort ..................................................... 38 Table 11. Write Operation Status ................................................... 38 Absolute Maximum Ratings. . . . . . . . . . . . . . . . . 39 Figure 10. Maximum Negative Overshoot Waveform ................... 39 Figure 11. Maximum Positive Overshoot Waveform..................... 39 Operating Ranges . . . . . . . . . . . . . . . . . . . . . . . . . 39 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Figure 1. Maximum Negative Overshoot Waveform ..................... 39 Figure 2. Maximum Positive Overshoot Waveform....................... 39 Operating Ranges . . . . . . . . . . . . . . . . . . . . . . . . . 39 DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 40 Test Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Table 4. Sector Group Protection/Unprotection Address Table .....18 Figure 12. Test Setup.................................................................... 41 Table 12. Test Specifications ......................................................... 41 Temporary Sector Group Unprotect ....................................... 19 Key to Switching Waveforms. . . . . . . . . . . . . . . . 41 Figure 1. Temporary Sector Group Unprotect Operation................ 19 Figure 2. In-System Sector Group Protect/Unprotect Algorithms ... 20 Figure 13. Input Waveforms and Measurement Levels...................................................................... 41 SecSi (Secured Silicon) Sector Flash Memory Region .......... 21 AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 42 Read-Only Operations ........................................................... 42 Table 5. SecSi Sector Contents ......................................................21 Figure 3. SecSi Sector Protect Verify.............................................. 22 Hardware Data Protection ...................................................... 22 Low VCC Write Inhibit ............................................................ 22 Write Pulse “Glitch” Protection ............................................... 22 Logical Inhibit .......................................................................... 22 Power-Up Write Inhibit ............................................................ 22 Common Flash Memory Interface (CFI) . . . . . . . 22 Table 6. CFI Query Identification String .............................. 23 Table 7. System Interface String......................................................23 Table 8. Device Geometry Definition................................... 24 Table 9. Primary Vendor-Specific Extended Query............. 25 Command Definitions . . . . . . . . . . . . . . . . . . . . . 25 Reading Array Data ................................................................ 25 Reset Command ..................................................................... 26 Autoselect Command Sequence ............................................ 26 Enter SecSi Sector/Exit SecSi Sector Command Sequence .. 26 Byte Program Command Sequence ....................................... 26 Unlock Bypass Command Sequence ..................................... 27 Write Buffer Programming ...................................................... 27 Accelerated Program .............................................................. 28 Figure 4. Write Buffer Programming Operation............................... 29 Figure 5. Program Operation .......................................................... 30 Program Suspend/Program Resume Command Sequence ... 30 Figure 6. Program Suspend/Program Resume............................... 31 Chip Erase Command Sequence ........................................... 31 Sector Erase Command Sequence ........................................ 31 Erase Suspend/Erase Resume Commands ........................... 32 Figure 7. Erase Operation............................................................... 33 Command Definitions ............................................................. 34 Figure 14. Read Operation Timings ............................................... 42 Figure 15. Page Read Timings ...................................................... 43 Hardware Reset (RESET#) .................................................... 44 Figure 16. Reset Timings ............................................................... 44 Erase and Program Operations .............................................. 45 Figure 17. Program Operation Timings.......................................... Figure 18. Accelerated Program Timing Diagram.......................... Figure 19. Chip/Sector Erase Operation Timings .......................... Figure 20. Data# Polling Timings (During Embedded Algorithms)...................................................... Figure 21. Toggle Bit Timings (During Embedded Algorithms)...................................................... Figure 22. DQ2 vs. DQ6................................................................. 46 46 47 48 49 49 Temporary Sector Unprotect .................................................. 50 Figure 23. Temporary Sector Group Unprotect Timing Diagram ... 50 Figure 24. Sector Group Protect and Unprotect Timing Diagram .. 51 Alternate CE# Controlled Erase and Program Operations ..... 52 Figure 25. Alternate CE# Controlled Write (Erase/Program) Operation Timings.......................................................................... 53 Erase And Programming Performance. . . . . . . . 54 Latchup Characteristics . . . . . . . . . . . . . . . . . . . . 54 TSOP Pin and BGA Package Capacitance . . . . . 55 Data Retention. . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Physical Dimensions . . . . . . . . . . . . . . . . . . . . . . 56 TS 048—48-Pin Standard Thin Small Outline Package ......... 56 TSR048—48-Pin Reverse Thin Small Outline Package ......... 57 FBE063—63-Ball Fine-Pitch Ball Grid Array, 12 x 11 mm Package .................................................................................. 58 Revision Summary . . . . . . . . . . . . . . . . . . . . . . . . 59 Table 10. Command Definitions.......................................................34 4 Am29LV065MU September 12, 2006 D A T A S H E E T PRODUCT SELECTOR GUIDE Part Number Am29LV065MU 90R (Note 3) (VIO = 3.0–3.6 V) VCC = 3.0–3.6 V Speed Option 101R (VIO = 2.7–3.6 V) 101 (VIO = 2.7–3.6 V) VCC = 2.7–3.6 V 112R (VIO = 1.65–3.6V) 112 (VIO = 1.65–3.6 V) 120R (VIO = 1.65–3.6 V) 120 (VIO = 1.65–3.6 V) Max. Access Time (ns) 90 100 110 120 Max. CE# Access Time (ns) 90 100 110 120 Max. Page access time (tPACC) 25 30 30 40 30 40 Max. OE# Access Time (ns) 25 30 30 40 30 40 Note: 1. See “AC Characteristics” for full specifications. 2. For the Am29LV065MU device, the last numeric digit in the speed option (e.g. 101, 112, 120) is used for internal purposes only. Please use OPNs as listed when placing orders. 3. Contact factory for availability and ordering information. BLOCK DIAGRAM DQ0–DQ7 RY/BY# VCC Sector Switches VSS VIO Erase Voltage Generator RESET# WE# Input/Output Buffers State Control ACC Command Register PGM Voltage Generator Chip Enable Output Enable Logic CE# OE# VCC Detector A22–A0 September 12, 2006 Timer Address Latch STB Am29LV065MU STB Data Latch Y-Decoder Y-Gating X-Decoder Cell Matrix 5 D A T A S H E E T CONNECTION DIAGRAMS NC A22 A16 A15 A14 A13 A12 A11 A9 A8 WE# RESET# ACC RY/BY# A18 A7 A6 A5 A4 A3 A2 A1 NC NC NC NC A17 VSS A20 A19 A10 DQ7 DQ6 DQ5 DQ4 VCC VIO A21 DQ3 DQ2 DQ1 DQ0 OE# VSS CE# A0 NC NC 6 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 48-Pin Standard TSOP 48-Pin Reverse TSOP Am29LV065MU 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 NC NC A17 VSS A20 A19 A10 DQ7 DQ6 DQ5 DQ4 VCC VIO A21 DQ3 DQ2 DQ1 DQ0 OE# VSS CE# A0 NC NC NC A22 A16 A15 A14 A13 A12 A11 A9 A8 WE# RESET# ACC RY/BY# A18 A7 A6 A5 A4 A3 A2 A1 NC NC September 12, 2006 D A T A S H E E T CONNECTION DIAGRAMS 63-Ball FBGA Top View, Balls Facing Down A8 B8 L8 M8 NC* NC* NC* NC* A7 B7 C7 D7 E7 F7 G7 H7 J7 K7 L7 M7 NC* NC* A14 A13 A15 A16 A17 NC A20 VSS NC* NC* C6 D6 E6 F6 G6 H6 J6 K6 A9 A8 A11 A12 A19 A10 DQ6 DQ7 C5 D5 E5 F5 G5 H5 J5 K5 WE# RESET# A22 NC DQ5 NC VCC DQ4 C4 D4 E4 F4 G4 H4 J4 K4 RY/BY# ACC NC NC DQ2 DQ3 VIO A21 C3 D3 E3 F3 G3 H3 J3 K3 A7 A18 A6 A5 DQ0 NC NC DQ1 A2 C2 D2 E2 F2 G2 H2 J2 K2 L2 M2 NC* A3 A4 A2 A1 A0 CE# OE# VSS NC* NC* L1 M1 NC* NC* A1 NC* B1 NC* * Balls are shorted together via the substrate but not connected to the die. Special Package Handling Instructions Special handling is required for Flash Memory products in molded packages (TSOP, BGA, SSOP, PLCC, PDIP). The package and/or data integrity may be September 12, 2006 compromised if the package body is exposed to temperatures above 150°C for prolonged periods of time. Am29LV065MU 7 D A T A PIN DESCRIPTION A22–A0 = 23 Address inputs DQ7–DQ0 = 8 Data inputs/outputs CE# = Chip Enable input OE# = Output Enable input WE# = Write Enable input ACC = Acceleration input RESET# = Hardware Reset Pin input RY/BY# = Ready/Busy output VCC = 3.0 volt-only single power supply (see Product Selector Guide for speed options and voltage supply tolerances) S H E E T LOGIC SYMBOL 23 A22–A0 CE# 8 DQ7–DQ0 OE# WE# VIO = Output Buffer power VSS = Device Ground NC = Pin Not Connected Internally 8 ACC RESET# RY/BY# VIO Am29LV065MU September 12, 2006 D A T A S H E E T ORDERING INFORMATION Standard Products AMD standard products are available in several packages and operating ranges. The order number (Valid Combination) is formed by a combination of the following: Am29LV065M U 120R WH I TEMPERATURE RANGE F = Industrial (-40°C to +85°C) with Pb-free Package I = Industrial (–40°C to +85°C) PACKAGE TYPE E = 48-Pin Standard Pinout Thin Small Outline Package (TS 048) F = 48-Pin Reverse Pinout Thin Small Outline Package (TSR048) WH = 63-Ball Fine-Pitch Ball Grid Array (FBGA) 0.80 mm pitch, 11 x 12 mm package (FBE063) SPEED OPTION See Product Selector Guide and Valid Combinations SECTOR ARCHITECTURE U = Uniform sector device DEVICE NUMBER/DESCRIPTION Am29LV065MU 64 Megabit (8 M x 8-Bit) MirrorBit™ Uniform Sector Flash Memory with VersatileIO™ Control 3.0 Volt-only Read, Program, and Erase Valid Combinations for TSOP Package Speed (ns) VIO Range Am29LV065MU101 100 2.7–3.6 V Am29LV065MU112 110 1.65–3.6 V 120 1.65–3.6 V Am29LV065MU120 Am29LV065MU101R EI, FI, EF 100 2.7–3.6 V Am29LV065MU112R 110 1.65–3.6 V Am29LV065MU120R 120 1.65–3.6 V VCC Range Valid Combinations for Fine-Pitch BGA Package 2.7–3.6 V Package Marking Order Number Speed (ns) VIO Range Am29LV065MU101 L065MU01V 100 2.7– 3.6 V Am29LV065MU112 L065MU11V 110 1.65– 3.6 V 120 1.65– 3.6 V 100 2.7– 3.6 V 3.0–3.6 V Am29LV065MU120 Am29LV065MU101R WHI WHF L065MU12V L065MU01R I, F Am29LV065MU112R L065MU11R 110 1.65– 3.6 V Am29LV065MU120R L065MU12R 120 1.65– 3.6 V VCC Range 2.7– 3.6 V 3.0– 3.6 V Valid Combinations Valid Combinations list configurations planned to be supported in volume for this device. Consult the local AMD sales office to confirm availability of specific valid combinations and to check on newly released combinations. Note: September 12, 2006 1. For the Am29LV065MU device, the last numeric digit in the speed option (e.g. 101, 112, 120) is used for internal purposes only. Please use OPNs as listed when placing orders. 2. For 90R speed option shown in product selector guide, contact AMD for availability and ordering information. Am29LV065MU 9 D A T A S H E E T DEVICE BUS OPERATIONS This section describes the requirements and use of the device bus operations, which are initiated through the internal command register. The command register itself does not occupy any addressable memory location. The register is a latch used to store the commands, along with the address and data information needed to execute the command. The contents of the Table 1. register serve as inputs to the internal state machine. The state machine outputs dictate the function of the device. Table 1 lists the device bus operations, the inputs and control levels they require, and the resulting output. The following subsections describe each of these operations in further detail. Device Bus Operations CE# OE# WE# RESET# ACC Addresses (Note 2) DQ7– DQ0 Read L L H H L/H AIN DOUT Write (Program/Erase) L H L H L/H AIN (Note 3) Accelerated Program L H L H VHH AIN (Note 3) VCC ± 0.3 V X X VCC ± 0.3 V L/H X High-Z Output Disable L H H H L/H X High-Z Reset X X X L L/H X High-Z Sector Group Protect (Note 2) L H L VID L/H SA, A6=L, A3=L, A2=L, A1=H, A0=L (Note 3) Sector Group Unprotect (Note 2) L H L VID L/H SA, A6=H, A3=L, A2=L, A1=H, A0=L (Note 3) Temporary Sector Group Unprotect X X X VID L/H AIN (Note 3) Operation Standby Legend: L = Logic Low = VIL, H = Logic High = VIH, VID = 11.5–12.5 V, VHH = 11.5–12.5 V, X = Don’t Care, SA = Sector Address, AIN = Address In, DIN = Data In, DOUT = Data Out Notes: 1. Addresses are A22:A0. Sector addresses are A22:A16. 2. The sector protect and sector unprotect functions may also be implemented via programming equipment. See “Sector Group Protection and Unprotection” on page 18.. 3. DIN or DOUT as required by command sequence, data polling, or sector protect algorithm (see Figure 2). VersatileIO™ (VIO) Control The VersatileIO™ (VIO) control allows the host system to set the voltage levels that the device generates and tolerates on CE# and DQ I/Os to the same voltage level that is asserted on VIO. See “Ordering Information” on page 9. for VIO options on this device. For example, a VI/O of 1.65–3.6 volts allows for I/O at the 1.8 or 3 volt levels, driving and receiving signals to and from other 1.8 or 3 V devices on the same data bus. Requirements for Reading Array Data To read array data from the outputs, the system must drive the CE# and OE# pins to VIL. CE# is the power control and selects the device. OE# is the output con- 10 trol and gates array data to the output pins. WE# should remain at VIH. The internal state machine is set for reading array data upon device power-up, or after a hardware reset. This ensures that no spurious alteration of the memory content occurs during the power transition. No command is necessary in this mode to obtain array data. Standard microprocessor read cycles that assert valid addresses on the device address inputs produce valid data on the device data outputs. The device remains enabled for read access until the command register contents are altered. See “Reading Array Data” on page 25. for more information. “Read-Only Operations” on page 42 for timing specifications and to Figure 13 for the timing diagram. Am29LV065MU September 12, 2006 D A T A See the table, “DC Characteristics” on page 40 for the active current specification for reading array data. Page Mode Read The device is capable of fast page mode read and is compatible with the page mode Mask ROM read operation. This mode provides faster read access speed for random locations within a page. The page size of the device is 8 bytes. The appropriate page is selected by the higher address bits A(max)–A3. Address bits A2–A0 determine the specific byte within a page. This is an asynchronous operation; the microprocessor supplies the specific byte location. The random or initial page access is equal to tACC or tCE and subsequent page read accesses (as long as the locations specified by the microprocessor falls within that page) is equivalent to tPACC. When CE# is deasserted and reasserted for a subsequent access, the access time is t ACC or t CE . Fast page mode accesses are obtained by keeping the “read-page addresses” constant and changing the “intra-read page” addresses. Writing Commands/Command Sequences To write a command or command sequence (which includes programming data to the device and erasing sectors of memory), the system must drive WE# and CE# to VIL, and OE# to VIH. The device features an Unlock Bypass mode to facilitate faster programming. Once the device enters the Unlock Bypass mode, only two write cycles are required to program a byte, instead of four. The “Byte Program Command Sequence” on page 26 has details on programming data to the device using both standard and Unlock Bypass command sequences. An erase operation can erase one sector, multiple sectors, or the entire device. Table 2 indicates the address space that each sector occupies. See the table, “DC Characteristics” on page 40 for the active current specification for the write mode. “AC Characteristics” on page 42 contains timing specification tables and timing diagrams for write operations. Write Buffer Write Buffer Programming allows the system to write a maximum of 32 bytes in one programming operation. This results in faster effective programming time than the standard programming algorithms. See “Write Buffer” for more information. Accelerated Program Operation The device offers accelerated program operations through the ACC function. This function is primarily intended to allow faster manufacturing throughput during system production. September 12, 2006 S H E E T If the system asserts VHH on this pin, the device automatically enters the aforementioned Unlock Bypass mode, temporarily unprotects any protected sectors, and uses the higher voltage on the pin to reduce the time required for program operations. The system would use a two-cycle program command sequence as required by the Unlock Bypass mode. Removing VHH from the ACC pin returns the device to normal operation. Note that the ACC pin must not be at VHH for operations other than accelerated programming, or device damage may result. In addition, the ACC pin must not be left floating or unconnected; inconsistent behavior of the device may result. Autoselect Functions If the system writes the autoselect command sequence, the device enters the autoselect mode. The system can then read autoselect codes from the internal register (which is separate from the memory array) on DQ7–DQ0. Standard read cycle timings apply in this mode. See “Autoselect Mode” on page 17. and “Autoselect Command Sequence” on page 26 for more information. Standby Mode When the system is not reading or writing to the device, it can place the device in the standby mode. In this mode, current consumption is greatly reduced, and the outputs are placed in the high impedance state, independent of the OE# input. The device enters the CMOS standby mode when the CE# and RESET# pins are both held at VIO ± 0.3 V. (Note that this is a more restricted voltage range than VIH.) If CE# and RESET# are held at VIH, but not within VIO ± 0.3 V, the device will be in the standby mode, but the standby current will be greater. The device requires standard access time (t CE ) for read access when the device is in either of these standby modes, before it is ready to read data. If the device is deselected during erasure or programming, the device draws active current until the operation is completed. See the table, “DC Characteristics” on page 40 for the standby current specification. Automatic Sleep Mode The automatic sleep mode minimizes Flash device energy consumption. The device automatically enables this mode when addresses remain stable for tACC + 30 ns. The automatic sleep mode is independent of the CE#, WE#, and OE# control signals. Standard address access timings provide new data when addresses are changed. While in sleep mode, output data is latched and always available to the system. Am29LV065MU 11 D A T A S H E E T See the table, “DC Characteristics” on page 40 for the automatic sleep mode current specification. memory, enabling the system to read the boot-up firmware from the Flash memory. RESET#: Hardware Reset Pin If RESET# is asserted during a program or erase operation, the RY/BY# pin remains a “0” (busy) until the internal reset operation is complete, which requires a time of tREADY (during Embedded Algorithms). The system can thus monitor RY/BY# to determine whether the reset operation is complete. If RESET# is asserted when a program or erase operation is not executing (RY/BY# pin is “1”), the reset operation is completed within a time of t READY (not during Embedded Algorithms). The system can read data tRH after the RESET# pin returns to VIH. The RESET# pin provides a hardware method of resetting the device to reading array data. When the RESET# pin is driven low for at least a period of tRP, the device immediately terminates any operation in progress, tristates all output pins, and ignores all read/write commands for the duration of the RESET# pulse. The device also resets the internal state machine to reading array data. The operation that was interrupted should be reinitiated once the device is ready to accept another command sequence, to ensure data integrity. Current is reduced for the duration of the RESET# pulse. When RESET# is held at VSS±0.3 V, the device draws CMOS standby current. If RESET# is held at VIL but not within VSS±0.3 V, the standby current will be greater. The RESET# pin may be tied to the system reset circuitry. A system reset would thus also reset the Flash 12 See the tables in “AC Characteristics” on page 42 for RESET# parameters and to Figure 15 for the timing diagram. Output Disable Mode When the OE# input is at VIH, output from the device is disabled. The output pins are placed in the high impedance state. Am29LV065MU September 12, 2006 D A T A Table 2. S H E E T Sector Address Table (Sheet 1 of 4) Sector A22 A21 A20 A19 A18 A17 A16 8-bit Address Range (in hexadecimal) SA0 0 0 0 0 0 0 0 000000–00FFFF SA1 0 0 0 0 0 0 1 010000–01FFFF SA2 0 0 0 0 0 1 0 020000–02FFFF SA3 0 0 0 0 0 1 1 030000–03FFFF SA4 0 0 0 0 1 0 0 040000–04FFFF SA5 0 0 0 0 1 0 1 050000–05FFFF SA6 0 0 0 0 1 1 0 060000–06FFFF SA7 0 0 0 0 1 1 1 070000–07FFFF SA8 0 0 0 1 0 0 0 080000–08FFFF SA9 0 0 0 1 0 0 1 090000–09FFFF SA10 0 0 0 1 0 1 0 0A0000–0AFFFF SA11 0 0 0 1 0 1 1 0B0000–0BFFFF SA12 0 0 0 1 1 0 0 0C0000–0CFFFF SA13 0 0 0 1 1 0 1 0D0000–0DFFFF SA14 0 0 0 1 1 1 0 0E0000–0EFFFF SA15 0 0 0 1 1 1 1 0F0000–0FFFFF SA16 0 0 1 0 0 0 0 100000–10FFFF SA17 0 0 1 0 0 0 1 110000–11FFFF SA18 0 0 1 0 0 1 0 120000–12FFFF SA19 0 0 1 0 0 1 1 130000–13FFFF SA20 0 0 1 0 1 0 0 140000–14FFFF SA21 0 0 1 0 1 0 1 150000–15FFFF SA22 0 0 1 0 1 1 0 160000–16FFFF SA23 0 0 1 0 1 1 1 170000–17FFFF SA24 0 0 1 1 0 0 0 180000–18FFFF SA25 0 0 1 1 0 0 1 190000–19FFFF SA26 0 0 1 1 0 1 0 1A0000–1AFFFF SA27 0 0 1 1 0 1 1 1B0000–1BFFFF SA28 0 0 1 1 1 0 0 1C0000–1CFFFF SA29 0 0 1 1 1 0 1 1D0000–1DFFFF SA30 0 0 1 1 1 1 0 1E0000–1EFFFF SA31 0 0 1 1 1 1 1 1F0000–1FFFFF SA32 0 1 0 0 0 0 0 200000–20FFFF SA33 0 1 0 0 0 0 1 210000–21FFFF September 12, 2006 Am29LV065MU 13 D A T A Table 2. 14 S H E E T Sector Address Table (Sheet 2 of 4) Sector A22 A21 A20 A19 A18 A17 A16 8-bit Address Range (in hexadecimal) SA34 0 1 0 0 0 1 0 220000–22FFFF SA35 0 1 0 0 0 1 1 230000–23FFFF SA36 0 1 0 0 1 0 0 240000–24FFFF SA37 0 1 0 0 1 0 1 250000–25FFFF SA38 0 1 0 0 1 1 0 260000–26FFFF SA39 0 1 0 0 1 1 1 270000–27FFFF SA40 0 1 0 1 0 0 0 280000–28FFFF SA41 0 1 0 1 0 0 1 290000–29FFFF SA42 0 1 0 1 0 1 0 2A0000–2AFFFF SA43 0 1 0 1 0 1 1 2B0000–2BFFFF SA44 0 1 0 1 1 0 0 2C0000–2CFFFF SA45 0 1 0 1 1 0 1 2D0000–2DFFFF SA46 0 1 0 1 1 1 0 2E0000–2EFFFF SA47 0 1 0 1 1 1 1 2F0000–2FFFFF SA48 0 1 1 0 0 0 0 300000–30FFFF SA49 0 1 1 0 0 0 1 310000–31FFFF SA50 0 1 1 0 0 1 0 320000–32FFFF SA51 0 1 1 0 0 1 1 330000–33FFFF SA52 0 1 1 0 1 0 0 340000–34FFFF SA53 0 1 1 0 1 0 1 350000–35FFFF SA54 0 1 1 0 1 1 0 360000–36FFFF SA55 0 1 1 0 1 1 1 370000–37FFFF SA56 0 1 1 1 0 0 0 380000–38FFFF SA57 0 1 1 1 0 0 1 390000–39FFFF SA58 0 1 1 1 0 1 0 3A0000–3AFFFF SA59 0 1 1 1 0 1 1 3B0000–3BFFFF SA60 0 1 1 1 1 0 0 3C0000–3CFFFF SA61 0 1 1 1 1 0 1 3D0000–3DFFFF SA62 0 1 1 1 1 1 0 3E0000–3EFFFF SA63 0 1 1 1 1 1 1 3F0000–3FFFFF SA64 1 0 0 0 0 0 0 400000–40FFFF SA65 1 0 0 0 0 0 1 410000–41FFFF SA66 1 0 0 0 0 1 0 420000–42FFFF SA67 1 0 0 0 0 1 1 430000–43FFFF SA68 1 0 0 0 1 0 0 440000–44FFFF Am29LV065MU September 12, 2006 D A T A Table 2. S H E E T Sector Address Table (Sheet 3 of 4) Sector A22 A21 A20 A19 A18 A17 A16 8-bit Address Range (in hexadecimal) SA69 1 0 0 0 1 0 1 450000–45FFFF SA70 1 0 0 0 1 1 0 460000–46FFFF SA71 1 0 0 0 1 1 1 470000–47FFFF SA72 1 0 0 1 0 0 0 480000–48FFFF SA73 1 0 0 1 0 0 1 490000–49FFFF SA74 1 0 0 1 0 1 0 4A0000–4AFFFF SA75 1 0 0 1 0 1 1 4B0000–4BFFFF SA76 1 0 0 1 1 0 0 4C0000–4CFFFF SA77 1 0 0 1 1 0 1 4D0000–4DFFFF SA78 1 0 0 1 1 1 0 4E0000–4EFFFF SA79 1 0 0 1 1 1 1 4F0000–4FFFFF SA80 1 0 1 0 0 0 0 500000–50FFFF SA81 1 0 1 0 0 0 1 510000–51FFFF SA82 1 0 1 0 0 1 0 520000–52FFFF SA83 1 0 1 0 0 1 1 530000–53FFFF SA84 1 0 1 0 1 0 0 540000–54FFFF SA85 1 0 1 0 1 0 1 550000–55FFFF SA86 1 0 1 0 1 1 0 560000–56FFFF SA87 1 0 1 0 1 1 1 570000–57FFFF SA88 1 0 1 1 0 0 0 580000–58FFFF SA89 1 0 1 1 0 0 1 590000–59FFFF SA90 1 0 1 1 0 1 0 5A0000–5AFFFF SA91 1 0 1 1 0 1 1 5B0000–5BFFFF SA92 1 0 1 1 1 0 0 5C0000–5CFFFF SA93 1 0 1 1 1 0 1 5D0000–5DFFFF SA94 1 0 1 1 1 1 0 5E0000–5EFFFF SA95 1 0 1 1 1 1 1 5F0000–5FFFFF SA96 1 1 0 0 0 0 0 600000–60FFFF SA97 1 1 0 0 0 0 1 610000–61FFFF SA98 1 1 0 0 0 1 0 620000–62FFFF SA99 1 1 0 0 0 1 1 630000–63FFFF SA100 1 1 0 0 1 0 0 640000–64FFFF SA101 1 1 0 0 1 0 1 650000–65FFFF SA102 1 1 0 0 1 1 0 660000–66FFFF SA103 1 1 0 0 1 1 1 670000–67FFFF September 12, 2006 Am29LV065MU 15 D A T A Table 2. S H E E T Sector Address Table (Sheet 4 of 4) Sector A22 A21 A20 A19 A18 A17 A16 8-bit Address Range (in hexadecimal) SA104 1 1 0 1 0 0 0 680000–68FFFF SA105 1 1 0 1 0 0 1 690000–69FFFF SA106 1 1 0 1 0 1 0 6A0000–6AFFFF SA107 1 1 0 1 0 1 1 6B0000–6BFFFF SA108 1 1 0 1 1 0 0 6C0000–6CFFFF SA109 1 1 0 1 1 0 1 6D0000–6DFFFF SA110 1 1 0 1 1 1 0 6E0000–6EFFFF SA111 1 1 0 1 1 1 1 6F0000–6FFFFF SA112 1 1 1 0 0 0 0 700000–70FFFF SA113 1 1 1 0 0 0 1 710000–71FFFF SA114 1 1 1 0 0 1 0 720000–72FFFF SA115 1 1 1 0 0 1 1 730000–73FFFF SA116 1 1 1 0 1 0 0 740000–74FFFF SA117 1 1 1 0 1 0 1 750000–75FFFF SA118 1 1 1 0 1 1 0 760000–76FFFF SA119 1 1 1 0 1 1 1 770000–77FFFF SA120 1 1 1 1 0 0 0 780000–78FFFF SA121 1 1 1 1 0 0 1 790000–79FFFF SA122 1 1 1 1 0 1 0 7A0000–7AFFFF SA123 1 1 1 1 0 1 1 7B0000–7BFFFF SA124 1 1 1 1 1 0 0 7C0000–7CFFFF SA125 1 1 1 1 1 0 1 7D0000–7DFFFF SA126 1 1 1 1 1 1 0 7E0000–7EFFFF SA127 1 1 1 1 1 1 1 7F0000–7FFFFF Note: All sectors are 64 Kbytes in size. 16 Am29LV065MU September 12, 2006 D A T A S H E E T Autoselect Mode In addition, when verifying sector protection, the sector address must appear on the appropriate highest order address bits (see Table 2). Table 3 shows the remaining address bits that are don’t care. When all necessary bits have been set as required, the programming equipment may then read the corresponding identifier code on DQ7–DQ0. The autoselect mode provides manufacturer and device identification, and sector protection verification, through identifier codes output on DQ7–DQ0. This mode is primarily intended for programming equipment to automatically match a device to be programmed with its corresponding programming algorithm. However, the autoselect codes can also be accessed in-system through the command register. To access the autoselect codes in-system, the host system can issue the autoselect command via the command register, as shown in Table 10. This method does not require VID. See “Autoselect Command Sequence” on page 26. for more information. When using programming equipment, the autoselect mode requires VID on address pin A9. Address pins A6, A3, A2, A1, and A0 must be as shown in Table 3. Table 3. Description Device ID Manufacturer ID: AMD Autoselect Codes, (High Voltage Method) CE# OE# WE# A21 to A15 A14 to A10 A9 A8 to A7 A6 A5 to A4 A3 to A2 A1 A0 DQ7 to DQ0 L L H X X VID X L X L L L 01h L L H 7Eh L L H X X VID X L X H H L 13h H H H 00h Cycle 1 Cycle 2 Cycle 3 Sector Protection Verification L L H SA X VID X L X L H L 01h (protected), 00h (unprotected) SecSi Sector Indicator Bit (DQ7) L L H X X VID X L X L H H 90h (factory locked), 10h (not factory locked) Legend: L = Logic Low = VIL, H = Logic High = VIH, SA = Sector Address, X = Don’t care. September 12, 2006 Am29LV065MU 17 D A T A Sector Group Protection and Unprotection S H E E T Table 4. Sector Group Protection/Unprotection Address Table The hardware sector group protection feature disables both program and erase operations in any sector group. In this device, a sector group consists of four adjacent sectors that are protected or unprotected at the same time (see Table 4). The hardware sector group unprotection feature re-enables both program and erase operations in previously protected sector groups. Sector group protection/unprotection can be implemented via two methods. Sector Group A22–A18 SA0–SA3 00000 Sector protection/unprotection requires VID on the RESET# pin only, and can be implemented either in-system or via programming equipment. Figure 2 shows the algorithms and Figure 23 shows the timing diagram. This method uses standard microprocessor bus cycle timing. For sector group unprotect, all unprotected sector groups must first be protected prior to the first sector group unprotect write cycle. The device is shipped with all sector groups unprotected. AMD offers the option of programming and protecting sector groups at its factory prior to shipping the device through AMD’s ExpressFlash™ Service. Contact an AMD representative for details. It is possible to determine whether a sector group is protected or unprotected. See “Autoselect Mode” on page 17. for details. SA4–SA7 00001 SA8–SA11 00010 SA12–SA15 00011 SA16–SA19 00100 SA20–SA23 00101 SA24–SA27 00110 SA28–SA31 00111 SA32–SA35 01000 SA36–SA39 01001 SA40–SA43 01010 SA44–SA47 01011 SA48–SA51 01100 SA52–SA55 01101 SA56–SA59 01110 SA60–SA63 01111 SA64–SA67 10000 SA68–SA71 10001 SA72–SA75 10010 SA76–SA79 10011 SA80–SA83 10100 SA84–SA87 10101 SA88–SA91 10110 SA92–SA95 10111 SA96–SA99 11000 SA100–SA103 11001 SA104–SA107 11010 SA108–SA111 11011 SA112–SA115 11100 SA116–SA119 11101 SA120–SA123 11110 SA124–SA127 11111 Note: All sector groups are 256 Kbytes in size. 18 Am29LV065MU September 12, 2006 D A T A S H E E T Temporary Sector Group Unprotect (Note: In this device, a sector group consists of four adjacent sectors that are protected or unprotected at the same time (see Table 4). START This feature allows temporary unprotection of previously protected sector groups to change data in-system. The Sector Group Unprotect mode is activated by setting the RESET# pin to VID. During this mode, formerly protected sector groups can be programmed or erased by selecting the sector group addresses. Once VID is removed from the RESET# pin, all the previously protected sector groups are protected again. Figure 1 shows the algorithm, and Figure 22 shows the timing diagrams, for this feature. RESET# = VID (Note 1) Perform Erase or Program Operations RESET# = VIH Temporary Sector Group Unprotect Completed (Note 2) Notes: 1. All protected sector groups unprotected. 2. All previously protected sector groups are protected once again. Figure 1. Temporary Sector Group Unprotect Operation September 12, 2006 Am29LV065MU 19 D A T A S H E E T START START PLSCNT = 1 RESET# = VID Wait 1 μs Temporary Sector Group Unprotect Mode No PLSCNT = 1 Protect all sector groups: The indicated portion of the sector group protect algorithm must be performed for all unprotected sector groups prior to issuing the first sector group unprotect address RESET# = VID Wait 1 μs First Write Cycle = 60h? First Write Cycle = 60h? Temporary Sector Group Unprotect Mode Yes Yes Set up sector group address No All sector groups protected? Yes Sector Group Protect: Write 60h to sector group address with A6–A0 = 0xx0010 Set up first sector group address Sector Group Unprotect: Write 60h to sector group address with A6–A0 = 1xx0010 Wait 150 µs Verify Sector Group Protect: Write 40h to sector group address with A6–A0 = 0xx0010 Increment PLSCNT No Reset PLSCNT = 1 Read from sector group address with A6–A0 = 0xx0010 Wait 15 ms Verify Sector Group Unprotect: Write 40h to sector group address with A6–A0 = 1xx0010 Increment PLSCNT No No PLSCNT = 25? Read from sector group address with A6–A0 = 1xx0010 Data = 01h? Yes No Yes Device failed Protect another sector group? Yes PLSCNT = 1000? No Yes Remove VID from RESET# Device failed Write reset command Sector Group Protect Algorithm Set up next sector group address No Data = 00h? Yes Last sector group verified? No Yes Sector Group Protect complete Sector Group Unprotect Algorithm Remove VID from RESET# Write reset command Sector Group Unprotect complete Figure 2. 20 In-System Sector Group Protect/Unprotect Algorithms Am29LV065MU September 12, 2006 D A T A S H E E T SecSi (Secured Silicon) Sector Flash Memory Region Factory Locked: SecSi Sector Programmed and Protected At the Factory The SecSi (Secured Silicon) Sector feature provides a Flash memory region that enables permanent part identification through an Electronic Serial Number (ESN). The SecSi Sector is 256 bytes in length, and uses a SecSi Sector Indicator Bit (DQ7) to indicate whether or not the SecSi Sector is locked when shipped from the factory. This bit is permanently set at the factory and cannot be changed, which prevents cloning of a factory locked part. This ensures the security of the ESN once the product is shipped to the field. In devices with an ESN, the SecSi Sector is protected when the device is shipped from the factory. The SecSi Sector cannot be modified in any way. A factory locked device has an 16-byte random ESN at addresses 000000h–00000Fh. AMD offers the device with the SecSi Sector either facto r y locked or c ustomer lock able. The factory-locked version is always protected when shipped from the factory, and has the SecSi (Secured Silicon) Sector Indicator Bit permanently set to a “1.” The customer-lockable version is shipped with the SecSi Sector unprotected, allowing customers to program the sector after receiving the device. The customer-lockable version also has the SecSi Sector Indicator Bit permanently set to a “0.” Thus, the SecSi Sector Indicator Bit prevents customer-lockable devices from being used to replace devices that are factory locked. The SecSi sector address space in this device is allocated as follows: Table 5. SecSi Sector Address Range 000000h–00000Fh ESN ESN or determined by customer 000010h–0000FFh Unavailable Determined by customer As an alternative to the factory-locked version, the device may be ordered such that the customer may program and protect the 256-byte SecSi sector. The system may program the SecSi Sector using the write-buffer, accelerated and/or unlock bypass methods, in addition to the standard programming command sequence. See “Command Definitions” on page 25.. Customer Lockable Determined by customer The SecSi Sector area can be protected using one of the following procedures: The system accesses the SecSi Sector through a command sequence (see “Enter SecSi Sector/Exit SecSi Sector Command Sequence”). After the system has written the Enter SecSi Sector command sequence, it may read the SecSi Sector by using the addresses normally occupied by the first sector (SA0). This mode of operation continues until the system issues the Exit SecSi Sector command sequence, or until power is removed from the device. On power-up, or following a hardware reset, the device reverts to sending commands to sector SA0. Note that the ACC function and unlock bypass modes are not available when the SecSi Sector is enabled. September 12, 2006 Customer Lockable: SecSi Sector NOT Programmed or Protected At the Factory Programming and protecting the SecSi Sector must be used with caution since, once protected, there is no procedure available for unprotecting the SecSi Sector area and none of the bits in the SecSi Sector memory space can be modified in any way. SecSi Sector Contents Standard ExpressFlash Factory Locked Factory Locked Customers may opt to have their code programmed by AMD through the AMD ExpressFlash service. The devices are then shipped from AMD’s factory with the SecSi Sector permanently locked. Contact an AMD representative for details on using AMD’s ExpressFlash service. ■ Write the three-cycle Enter SecSi Sector Region command sequence, and then follow the in-system sector protect algorithm as shown in Figure 2, except that RESET# may be at either VIH or VID. This allows in-system protection of the SecSi Sector without raising any device pin to a high voltage. Note that this method is only applicable to the SecSi Sector. ■ To verify the protect/unprotect status of the SecSi Sector, follow the algorithm shown in Figure 3. Once the SecSi Sector is programmed, locked and verified, the system must write the Exit SecSi Sector Region command sequence to return to reading and writing within the remainder of the array. Am29LV065MU 21 D A T A S H E E T . spurious system level signals during V CC power-up and power-down transitions, or from system noise. START RESET# = VIH or VID Wait 1 μs Write 60h to any address Write 40h to SecSi Sector address with A6 = 0, A1 = 1, A0 = 0 Read from SecSi Sector address with A6 = 0, A1 = 1, A0 = 0 Figure 3. Low VCC Write Inhibit If data = 00h, SecSi Sector is unprotected. If data = 01h, SecSi Sector is protected. When VCC is less than VLKO, the device does not accept any write cycles. This protects data during VCC power-up and power-down. The command register and all internal program/erase circuits are disabled, and the device resets to the read mode. Subsequent writes are ignored until VCC is greater than VLKO. The system must provide the proper signals to the control pins to prevent unintentional writes when V CC is greater than VLKO. Remove VIH or VID from RESET# Write reset command Write Pulse “Glitch” Protection Noise pulses of less than 5 ns (typical) on OE#, CE# or WE# do not initiate a write cycle. SecSi Sector Protect Verify complete Logical Inhibit Write cycles are inhibited by holding any one of OE# = VIL, CE# = VIH or WE# = VIH. To initiate a write cycle, CE# and WE# must be a logical zero while OE# is a logical one. SecSi Sector Protect Verify Hardware Data Protection The command sequence requirement of unlock cycles for programming or erasing provides data protection against inadvertent writes (see Table 10 for command definitions). In addition, the following hardware data protection measures prevent accidental erasure or programming, which might otherwise be caused by Power-Up Write Inhibit If WE# = CE# = VIL and OE# = VIH during power up, the device does not accept commands on the rising edge of WE#. The internal state machine is automatically reset to the read mode on power-up. COMMON FLASH MEMORY INTERFACE (CFI) The Common Flash Interface (CFI) specification outlines device and host system software interrogation handshake, which allows specific vendor-specified software algorithms to be used for entire families of devices. Software support can then be device-independent, JEDEC ID-independent, and forward- and backward-compatible for the specified flash device families. Flash vendors can standardize their existing interfaces for long-term compatibility. This device enters the CFI Query mode when the system writes the CFI Query command, 98h, to address 55h, any time the device is ready to read array data. The system can read CFI information at the addresses given in Tables 6–9. To terminate reading CFI data, the system must write the reset command. 22 The system can also write the CFI query command when the device is in the autoselect mode. The device enters the CFI query mode, and the system can read CFI data at the addresses given in Tables 6–9. The system must write the reset command to return the device to reading array data. For further information, please refer to the CFI Specification and CFI Publication 100, available via the World Wide Web at http://www.amd.com/flash/cfi. Alternatively, contact an AMD representative for copies of these documents. Am29LV065MU September 12, 2006 D A T A Table 6. S H E E T CFI Query Identification String Addresses Data Description 10h 11h 12h 51h 52h 59h Query Unique ASCII string “QRY” 13h 14h 02h 00h Primary OEM Command Set 15h 16h 40h 00h Address for Primary Extended Table 17h 18h 00h 00h Alternate OEM Command Set (00h = none exists) 19h 1Ah 00h 00h Address for Alternate OEM Extended Table (00h = none exists) Table 7. System Interface String Addresses Data 1Bh 27h VCC Min. (write/erase) D7–D4: volt, D3–D0: 100 millivolt 1Ch 36h VCC Max. (write/erase) D7–D4: volt, D3–D0: 100 millivolt 1Dh 00h VPP Min. voltage (00h = no VPP pin present) 1Eh 00h VPP Max. voltage (00h = no VPP pin present) 1Fh 07h Typical timeout per single byte write 2N µs 20h 07h Typical timeout for Min. size buffer write 2N µs (00h = not supported) 21h 0Ah Typical timeout per individual block erase 2N ms 22h 00h Typical timeout for full chip erase 2N ms (00h = not supported) 23h 01h Max. timeout for byte write 2N times typical 24h 05h Max. timeout for buffer write 2N times typical 25h 04h Max. timeout per individual block erase 2N times typical 26h 00h Max. timeout for full chip erase 2N times typical (00h = not supported) September 12, 2006 Description Am29LV065MU 23 D A T A Table 8. 24 S H E E T Device Geometry Definition Addresses Data Description 27h 17h Device Size = 2N byte 28h 29h 00h 00h Flash Device Interface description (refer to CFI publication 100) (00h not supported) 2Ah 2Bh 05h 00h Max. number of byte in multi-byte write = 2N (00h = not supported) 2Ch 01h Number of Erase Block Regions within device (01h = uniform device, 02h = boot device) 2Dh 2Eh 2Fh 30h 7Fh 00h 00h 01h Erase Block Region 1 Information (refer to the CFI specification or CFI publication 100) 31h 32h 33h 34h 00h 00h 00h 00h Erase Block Region 2 Information (refer to CFI publication 100) 35h 36h 37h 38h 00h 00h 00h 00h Erase Block Region 3 Information (refer to CFI publication 100) 39h 3Ah 3Bh 3Ch 00h 00h 00h 00h Erase Block Region 4 Information (refer to CFI publication 100) Am29LV065MU September 12, 2006 D A T A Table 9. S H E E T Primary Vendor-Specific Extended Query Addresses Data Description 40h 41h 42h 50h 52h 49h Query-unique ASCII string “PRI” 43h 31h Major version number, ASCII 44h 33h Minor version number, ASCII 45h 09h Address Sensitive Unlock (Bits 1-0) 0 = Required, 1 = Not Required Process Technology (Bits 7-2) 0010b = 0.23 µm MirrorBit 46h 02h Erase Suspend 0 = Not Supported, 1 = To Read Only, 2 = To Read & Write 47h 04h Sector Protect 0 = Not Supported, X = Number of sectors per group 48h 01h Sector Temporary Unprotect 00 = Not Supported, 01 = Supported 49h 04h Sector Protect/Unprotect scheme 04 = 29LV800 mode 4Ah 00h Simultaneous Operation 00 = Not Supported, X = Number of Sectors in Bank 4Bh 00h Burst Mode Type 00 = Not Supported, 01 = Supported 4Ch 01h Page Mode Type 00 = Not Supported, 01 = 8 Byte Page 4Dh B5h 4Eh C5h ACC (Acceleration) Supply Minimum 00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV ACC (Acceleration) Supply Maximum 00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV Top/Bottom Boot Sector Flag 4Fh 00h 50h 01h 00h = Uniform Device without WP# protect, 02h = Bottom Boot Device, 03h = Top Boot Device, 04h = Uniform sectors bottom WP# protect, 05h = Uniform sectors top WP# protect Program Suspend 00h = Not Supported, 01h = Supported COMMAND DEFINITIONS Writing specific address and data commands or sequences into the command register initiates device operations. Table 10 defines the valid register command sequences. Writing incorrect address and data values or writing them in the improper sequence may place the device in an unknown state. A reset command is then required to return the device to reading array data. All addresses are latched on the falling edge of WE# or CE#, whichever happens later. All data is latched on the rising edge of WE# or CE#, whichever happens September 12, 2006 first. Refer to the AC Characteristics section for timing diagrams. Reading Array Data The device is automatically set to reading array data after device power-up. No commands are required to retrieve data. The device is ready to read array data after completing an Embedded Program or Embedded Erase algorithm. After the device accepts an Erase Suspend command, the device enters the erase-suspend-read mode, after which the system can read data from any Am29LV065MU 25 D A T A non-erase-suspended sector. After completing a programming operation in the Erase Suspend mode, the system may once again read array data with the same exception. See “Erase Suspend/Erase Resume Commands” on page 32. for more information. The system must issue the reset command to return the device to the read (or erase-suspend-read) mode if DQ5 goes high during an active program or erase operation, or if the device is in the autoselect mode. See the next section, Reset Command, for more information. See “Requirements for Reading Array Data” on page 10. for more infor mation. See the table, “Read-Only Operations” on page 42 provides the read parameters, and Figure 13 shows the timing diagram. Reset Command Writing the reset command resets the device to the read or erase-suspend-read mode. Address bits are don’t cares for this command. The reset command may be written between the sequence cycles in an erase command sequence before erasing begins. This resets the device to the read mode. Once erasure begins, however, the device ignores reset commands until the operation is complete. The reset command may be written between the sequence cycles in a program command sequence before programming begins. This resets the device to the read mode. If the program command sequence is written while the device is in the Erase Suspend mode, writing the reset command returns the device to the erase-suspend-read mode. Once programming begins, however, the device ignores reset commands until the operation is complete. The reset command may be written between the sequence cycles in an autoselect command sequence. Once in the autoselect mode, the reset command must be written to return to the read mode. If the device entered the autoselect mode while in the Erase Suspend mode, writing the reset command returns the device to the erase-suspend-read mode. If DQ5 goes high during a program or erase operation, writing the reset command returns the device to the read mode (or erase-suspend-read mode if the device was in Erase Suspend). Note that if DQ1 goes high during a Write Buffer Programming operation, the system must write the Write-to-Buffer-Abort Reset command sequence to reset the device for the next operation. Autoselect Command Sequence The autoselect command sequence allows the host system to access the manufacturer and device codes, and determine whether or not a sector is protected. 26 S H E E T Table 10 shows the address and data requirements. This method is an alternative to that shown in Table 3, which is intended for PROM programmers and requires V ID on address pin A9. The autoselect command sequence may be written to an address that is either in the read or erase-suspend-read mode. The autoselect command may not be written while the device is actively programming or erasing. The autoselect command sequence is initiated by first writing two unlock cycles. This is followed by a third write cycle that contains the autoselect command. The device then enters the autoselect mode. The system may read at any address any number of times without initiating another autoselect command sequence: ■ A read cycle at address XX00h returns the manufacturer code. ■ Three read cycles at addresses 01h, 0Eh, and 0Fh return the device code. ■ A read cycle to an address containing a sector group address (SA), and the address 02h on A7–A0 returns 01h if the sector group is protected, or 00h if it is unprotected. (See Table 4 for valid sector addresses). The system must write the reset command to return to the read mode (or erase-suspend-read mode if the device was previously in Erase Suspend). Enter SecSi Sector/Exit SecSi Sector Command Sequence The SecSi Sector region provides a secured data area containing an 16-byte random Electronic Serial Number (ESN). The system can access the SecSi Sector region by issuing the three-cycle Enter SecSi Sector command sequence. The device continues to access the SecSi Sector region until the system issues the four-cycle Exit SecSi Sector command sequence. The Exit SecSi Sector command sequence returns the device to normal operation. Table 10 shows the address and data requirements for both command sequences. See also “SecSi (Secured Silicon) Sector Flash Memory Region” for further information. Note that the ACC function and unlock bypass modes are not available when the SecSi Sector is enabled. Byte Program Command Sequence Programming is a four-bus-cycle operation. The program command sequence is initiated by writing two unlock write cycles, followed by the program set-up command. The program address and data are written next, which in turn initiate the Embedded Program algorithm. The system is not required to provide further controls or timings. The device automatically provides internally generated program pulses and verifies the programmed cell margin. Table 10 shows the address Am29LV065MU September 12, 2006 D A T A and data requirements for the byte program command sequence. When the Embedded Program algorithm is complete, the device then returns to the read mode and addresses are no longer latched. The system can determine the status of the program operation by using DQ7, DQ6, or RY/BY#. See “Write Operation Status” on page 35. for information on these status bits. Any commands written to the device during the Embedded Program Algorithm are ignored. Note that a hardware reset immediately terminates the program operation. The program command sequence should be reinitiated once the device has returned to the read mode, to ensure data integrity. Note that the SecSi Sector, autoselect, and CFI functions are unavailable when a program operation is in progress. Programming is allowed in any sequence and across sector boundaries. A bit cannot be programmed from “0” back to a “1.” Attempting to do so may cause the device to set DQ5 = 1, or cause the DQ7 and DQ6 status bits to indicate the operation was successful. However, a succeeding read will show that the data is still “0.” Only erase operations can convert a “0” to a “1.” Unlock Bypass Command Sequence The unlock bypass feature allows the system to program bytes to the device faster than using the standard program command sequence. The unlock bypass command sequence is initiated by first writing two unlock cycles. This is followed by a third write cycle containing the unlock bypass command, 20h. The device then enters the unlock bypass mode. A two-cycle unlock bypass program command sequence is all that is required to program in this mode. The first cycle in this sequence contains the unlock bypass program command, A0h; the second cycle contains the program address and data. Additional data is programmed in the same manner. This mode dispenses with the initial two unlock cycles required in the standard program command sequence, resulting in faster total programming time. Table 10 shows the requirements for the command sequence. During the unlock bypass mode, only the Unlock Bypass Program and Unlock Bypass Reset commands are valid. To exit the unlock bypass mode, the system must issue the two-cycle unlock bypass reset command sequence. The first cycle must contain the data 90h. The second cycle must contain the data 00h. The device then returns to the read mode. Write Buffer Programming Write buffer programming allows the system to write a maximum of 32 bytes in one programming operation. The effective programming time is faster than the stan- September 12, 2006 S H E E T dard programming algorithms. The write buffer programming command sequence is initiated by first writing two unlock cycles. This is followed by a third write cycle containing the Write Buffer Load command written at the Sector Address in which programming will occur. The fourth cycle writes the sector address and the number of byte locations, minus one, to be programmed. For example, if the system will program 6 unique address locations, then 05h should be written to the device. This tells the device how many write buffer addresses will be loaded with data and therefore when to expect the Program Buffer to Flash command. The number of locations to program cannot exceed the size of the write buffer or the operation will abort. The fifth cycle writes the first address location and data to be programmed. A write-buffer-page is selected by address bits AMAX–A5. All subsequent add r e s s / d a t a p a i r s m u s t fa l l w i t h i n t h e selected-write-buffer-page. The system then writes the remaining address/data pairs into the write buffer. Write buffer locations may be loaded in any order. The write-buffer-page address must be the same for all address/data pairs loaded into the write buffer. That is, write buffer programming cannot occur across multiple write-buffer pages or sectors. If the system attempts to load programming data outside of the selected write-buffer page, the operation will abort. Note that if a Write Buffer address location is loaded multiple times, the address/data pair counter will be decremented for every data load operation. The host s y s t e m m u s t t h e r e fo r e a c c o u n t fo r l o a d i n g a write-buffer location more than once. The counter decrements for each data load operation, not for each unique write-buffer-address location. Additionally, the last data loaded prior to the Program Buffer to Flash command will be programmed into the device. Note also that if an address location is loaded more than once into the buffer, the final data loaded for that address will be programmed. Once the specified number of write buffer locations have been loaded, the system must then write the Program Buffer to Flash command at the sector address. Any other address and data combination aborts the Write Buffer Programming operation. The device then begins programming. Data polling should be used while monitoring the last address location loaded into the write buffer. DQ7, DQ6, DQ5, and DQ1 should be monitored to determine the device status during Write Buffer Programming. The write-buffer programming operation can be suspended using the standard program suspend/resume commands. Upon successful completion of the Write Buffer Programming operation, the device is ready to execute the next command. Am29LV065MU 27 D A T A The Write Buffer Programming Sequence can be aborted in the following ways: ■ Load a value that is greater than the page buffer size during the Number of Locations to Program step. ■ Write to an address in a sector different than the one specified during the Write-Buffer-Load command. ■ Write an Address/Data pair to a different write-buffer-page than the one selected by the Starting Address during the write buffer data loading stage of the operation. ■ Write data other than the Confirm Command after the specified number of data load cycles. The abort condition is indicated by DQ1 = 1, DQ7 = DATA# (for the last address location loaded), DQ6 = toggle, and DQ5=0. A Write-to-Buffer-Abort Reset command sequence must be written to reset the device for the next operation. Note that the full 3-cycle Write-to-Buffer-Abort Reset command sequence is re- 28 S H E E T quired when using Write-Buffer-Programming features in Unlock Bypass mode. Accelerated Program The device offers accelerated program operations through the ACC pin. When the system asserts VHH on the ACC pin, the device automatically enters the Unlock Bypass mode. The system may then write the two-cycle Unlock Bypass program command sequence. The device uses the higher voltage on the ACC pin to accelerate the operation. Note that the ACC pin must not be at VHH for operations other than accelerated programming, or device damage may result. In addition, the ACC pin must not be left floating or unconnected; inconsistent behavior of the device may result. Figure 4 illustrates the algorithm for the program operation. See the table, “Erase and Program Operations” on page 45 for parameters, and Figure 16 for timing diagrams. Am29LV065MU September 12, 2006 D A T A S H E E T Write “Write to Buffer” command and Sector Address Part of “Write to Buffer” Command Sequence Write number of addresses to program minus 1(WC) and Sector Address Write first address/data Yes WC = 0 ? No Write to a different sector address Abort Write to Buffer Operation? Yes Write to buffer ABORTED. Must write “Write-to-buffer Abort Reset” command sequence to return to read mode. No ((Note 1)) Write next address/data pair WC = WC - 1 Write program buffer to flash sector address Notes: Read DQ7 - DQ0 at Last Loaded Address When Sector Address is specified, any address in the selected sector is acceptable. However, when loading Write-Buffer address locations with data, all addresses must fall within the selected Write-Buffer Page. 2. DQ7 may change simultaneously with DQ5. Therefore, DQ7 should be verified. 3. If this flowchart location was reached because DQ5= “1”, then the device FAILED. If this flowchart location was reached because DQ1= “1”, then the Write to Buffer operation was ABORTED. In either case, the proper reset command must be written before the device can begin another operation. If DQ1=1, write the Write-Buffer-Programming-Abort-Reset command. if DQ5=1, write the Reset command. 4. See Table 10 for command sequences required for write buffer programming. Yes DQ7 = Data? No 1. No No DQ1 = 1? DQ5 = 1? Yes Yes Read DQ7 - DQ0 with address = Last Loaded Address ((Note 2)) DQ7 = Data? Yes No ((Note 3)) FAIL or ABORT Figure 4. September 12, 2006 PASS Write Buffer Programming Operation Am29LV065MU 29 D A T A S H E E T Program Suspend/Program Resume Command Sequence The Program Suspend command allows the system to interrupt a programming operation or a Write to Buffer programming operation so that data can be read from any non-suspended sector. When the Program Suspend command is written during a programming process, the device halts the program operation within 15 μs maximum (5 μs typical) and updates the status bits. Addresses are not required when writing the Program Suspend command. START Write Program Command Sequence Data Poll from System Embedded Program algorithm in progress Verify Data? Yes Increment Address No Last Address? Yes Programming Completed Note: See Table 10 for program command sequence. Figure 5. Program Operation No After the programming operation has been suspended, the system can read array data from any non-suspended sector. The Program Suspend command may also be issued during a programming operation while an erase is suspended. In this case, data may be read from any addresses not in Erase Suspend or Program Suspend. If a read is needed from the SecSi Sector area (One-time Program area), then user must use the proper command sequences to enter and exit this region. The system may also write the autoselect command sequence when the device is in the Program Suspend mode. The system can read as many autoselect codes as required. When the device exits the autoselect mode, the device reverts to the Program Suspend mode, and is ready for another valid operation. See “Autoselect Command Sequence” on page 26. for more information. After the Program Resume command is written, the device reverts to programming. The system can determine the status of the program operation using the DQ7 or DQ6 status bits, just as in the standard program operation. See “Write Operation Status” on page 35. for more information. The system must write the Program Resume command (address bits are don’t care) to exit the Program Suspend mode and continue the programming operation. Further writes of the Resume command are ignored. Another Program Suspend command can be written after the device has resume programming. 30 Am29LV065MU September 12, 2006 D A T A When the Embedded Erase algorithm is complete, the device returns to the read mode and addresses are no longer latched. The system can determine the status of the erase operation by using DQ7, DQ6, DQ2, or RY/BY#. See “Write Operation Status” on page 35. for information on these status bits. Note that the SecSi Sector, autoselect, and CFI functions are unavailable when an erase operation is in progress. Program Operation or Write-to-Buffer Sequence in Progress Write address/data XXXh/B0h Write Program Suspend Command Sequence Command is also valid for Erase-suspended-program operations Wait 15 μs Read data as required No Autoselect and SecSi Sector read operations are also allowed Data cannot be read from erase- or program-suspended sectors Done reading? Yes Write address/data XXXh/30h Program Suspend/Program Resume Chip Erase Command Sequence Chip erase is a six bus cycle operation. The chip erase command sequence is initiated by writing two unlock cycles, followed by a set-up command. Two additional unlock write cycles are then followed by the chip erase command, which in turn invokes the Embedded Erase algorithm. The device does not require the system to preprogram prior to erase. The Embedded Erase algorithm automatically preprograms and verifies the entire memory for an all zero data pattern prior to electrical erase. The system is not required to provide any controls or timings during these operations. Table 10 shows the address and data requirements for the chip erase command sequence. September 12, 2006 Any commands written during the chip erase operation are ignored. However, note that a hardware reset immediately terminates the erase operation. If that occurs, the chip erase command sequence should be reinitiated once the device has returned to reading array data, to ensure data integrity. Figure 6 illustrates the algorithm for the erase operation. See the table, “Erase and Program Operations” on page 45 for parameters, and Figure 18 section for timing diagrams. Sector Erase Command Sequence Write Program Resume Command Sequence Device reverts to operation prior to Program Suspend Figure 6. S H E E T Sector erase is a six bus cycle operation. The sector erase command sequence is initiated by writing two unlock cycles, followed by a set-up command. Two additional unlock cycles are written, and are then followed by the address of the sector to be erased, and the sector erase command. Table 10 shows the address and data requirements for the sector erase command sequence. The device does not require the system to preprogram prior to erase. The Embedded Erase algorithm automatically programs and verifies the entire memory for an all zero data pattern prior to electrical erase. The system is not required to provide any controls or timings during these operations. After the command sequence is written, a sector erase time-out of 50 µs occurs. During the time-out period, additional sector addresses and sector erase commands may be written. Loading the sector erase buffer may be done in any sequence, and the number of sectors may be from one sector to all sectors. The time between these additional cycles must be less than 50 µs, otherwise erasure may begin. Any sector erase address and command following the exceeded time-out may or may not be accepted. It is recommended that processor interrupts be disabled during this time to ensure all commands are accepted. The interrupts can be re-enabled after the last Sector Erase command is written. Any command other than Sector Erase or Erase Suspend during the time-out period resets the device to the read mode. The system must rewrite the command sequence and any additional addresses and commands. Note that the SecSi Sector, autoselect, and CFI functions are unavailable when an erase operation is in progress. Am29LV065MU 31 D A T A The system can monitor DQ3 to determine if the sector erase timer has timed out (See “DQ3: Sector Erase Timer” on page 37..). The time-out begins from the rising edge of the final WE# pulse in the command sequence. When the Embedded Erase algorithm is complete, the device returns to reading array data and addresses are no longer latched. The system can determine the status of the erase operation by reading DQ7, DQ6, DQ2, or RY/BY# in the erasing sector. See “Write Operation Status” on page 35. for information on these status bits. Once the sector erase operation has begun, only the Erase Suspend command is valid. All other commands are ignored. However, note that a hardware reset immediately terminates the erase operation. If that occurs, the sector erase command sequence should be reinitiated once the device has returned to reading array data, to ensure data integrity. Figure 6 illustrates the algorithm for the erase operation. See the tables, “Erase and Program Operations” on page 45 for parameters, and Figure 18 for timing diagrams. Erase Suspend/Erase Resume Commands The Erase Suspend command, B0h, allows the system to interrupt a sector erase operation and then read data from, or program data to, any sector not selected for erasure. This command is valid only during the sector erase operation, including the 50 µs time-out period during the sector erase command sequence. The Erase Suspend command is ignored if written during the chip erase operation or Embedded Program algorithm. When the Erase Suspend command is written during the sector erase operation, the device requires a typical of 5 µs (maximum 20 μs) to suspend the erase operation. However, when the Erase Suspend command is written during the sector erase time-out, the device immediately terminates the time-out period and suspends the erase operation. 32 S H E E T After the erase operation has been suspended, the device enters the erase-suspend-read mode. The system can read data from or program data to any sector not selected for erasure. (The device “erase suspends” all sectors selected for erasure.) Reading at any address within erase-suspended sectors produces status information on DQ7–DQ0. The system can use DQ7, or DQ6 and DQ2 together, to determine if a sector is actively erasing or is erase-suspended. See “Write Operation Status” on page 35. for information on these status bits. After an erase-suspended program operation is complete, the device returns to the erase-suspend-read mode. The system can determine the status of the program operation using the DQ7 or DQ6 status bits, just as in the standard byte program operation. See “Write Operation Status” on page 35. for more information. In the erase-suspend-read mode, the system can also issue the autoselect command sequence. See “Autoselect Mode” on page 17. and “Autoselect Command Sequence” on page 26 for details. To resume the sector erase operation, the system must write the Erase Resume command. Further writes of the Resume command are ignored. Another Erase Suspend command can be written after the chip has resumed erasing. Note: During an erase operation, this flash device performs multiple internal operations which are invisible to the system. When an erase operation is suspended, any of the internal operations that were not fully completed must be restarted. As such, if this flash device is continually issued suspend/resume commands in rapid succession, erase progress will be impeded as a function of the number of suspends. The result will be a longer cumulative erase time than without suspends. Note that the additional suspends do not affect device reliability or future performance. In most systems rapid erase/suspend activity occurs only briefly. In such cases, erase performance will not be significantly impacted. Am29LV065MU September 12, 2006 D A T A S H E E T START Write Erase Command Sequence (Notes 1, 2) Data Poll to Erasing Bank from System No Embedded Erase algorithm in progress Data = FFh? Yes Erasure Completed Notes: 1. See Table 10 for erase command sequence. 2. See “DQ3: Sector Erase Timer” on page 37 for information on the sector erase timer. Figure 7. September 12, 2006 Erase Operation Am29LV065MU 33 D A T A S H E E T Command Definitions Table 10. Read ((Note 5)) Autoselect ((Note 7)) Reset ((Note 6)) Bus Cycles (Notes 1, 2, 3, and 4) Cycles Command Sequence (Notes) Command Definitions Addr Data 1 RA RD First Second Third Fourth Addr Data Addr Data Addr Fifth Data 1 XXX F0 Manufacturer ID 4 XXX AA XXX 55 XXX 90 X00 01 Device ID ((Note 8)) 6 XXX AA XXX 55 XXX 90 X01 7E SecSi™ Sector Factory Protect ((Note 9)) 4 XXX AA XXX 55 XXX 90 X03 (9) Sector Group Protect Verify ((Note 10)) 4 XXX AA XXX 55 XXX 90 (SA)X02 00/01 Sixth Addr Data Addr Data X0E 13 X0F 00 Enter SecSi Sector Region 3 XXX AA XXX 55 XXX 88 Exit SecSi Sector Region 4 XXX AA XXX 55 XXX 90 XXX 00 Program 4 XXX AA XXX 55 XXX A0 PA PD Write to Buffer 6 XXX AA XXX 55 SA 25 SA WC PA PD WBL PD Program Buffer to Flash 1 SA 29 Write to Buffer Abort Reset ((Note 11)) 3 XXX AA XXX 55 XXX F0 Unlock Bypass 3 XXX AA XXX 55 XXX 20 Unlock Bypass Program ((Note 12)) 2 XXX A0 PA PD Unlock Bypass Reset ((Note 13)) 2 XXX 90 XXX 00 Chip Erase 6 XXX AA XXX 55 XXX 80 XXX AA XXX 55 XXX 10 Sector Erase 6 XXX AA XXX 55 XXX 80 XXX AA XXX 55 SA 30 Program/Erase Suspend ((Note 14)) 1 XXX B0 Program/Erase Resume ((Note 15)) 1 XXX 30 CFI Query ((Note 15)) 1 55 98 Legend: X = Don’t care RA = Read Address of the memory location to be read. RD = Read Data read from location RA during read operation. PA = Program Address. Addresses latch on the falling edge of the WE# or CE# pulse, whichever happens later. PD = Program Data for location PA. Data latches on the rising edge of WE# or CE# pulse, whichever happens first. Notes: 1. See Table 1 for description of bus operations. 2. All values are in hexadecimal. 9. 3. Except for the read cycle and the fourth cycle of the autoselect command sequence, all bus cycles are write cycles. 4. During unlock and command cycles, when lower address bits are don’t cares, address bits A22–A12 are also don’t cares. 5. No unlock or command cycles required when device is in read mode. 6. The Reset command is required to return to the read mode (or to the erase-suspend-read mode if previously in Erase Suspend) when the device is in the autoselect mode, or if DQ5 goes high (while the device is providing status information). 7. 8. 34 The fourth cycle of the autoselect command sequence is a read cycle. See “Autoselect Command Sequence” on page 26. for more information. The device ID must be read in three cycles. SA = Sector Address of sector to be verified (in autoselect mode) or erased. Address bits A22–A16 uniquely select any sector. WBL = Write Buffer Location. Address must be within the same write buffer page as PA. BC = Byte Count. Number of write buffer locations to load minus 1. The data is 88h for factory locked and 08h for not factory locked. 10. The data is 00h for an unprotected sector group and 01h for a protected sector group. 11. Command sequence resets device for next command after aborted write-to-buffer operation. 12. The Unlock Bypass command is required prior to the Unlock Bypass Program command. 13. The Unlock Bypass Reset command is required to return to the read mode when the device is in the unlock bypass mode. 14. The system may read and program in non-erasing sectors, or enter the autoselect mode, when in the Erase Suspend mode. The Erase Suspend command is valid only during a sector erase operation. 15. The Erase Resume command is valid only during the Erase Suspend mode. 16. Command is valid when device is ready to read array data or when device is in autoselect mode. Am29LV065MU September 12, 2006 D A T A S H E E T WRITE OPERATION STATUS The device provides several bits to determine the status of a program or erase operation: DQ2, DQ3, DQ5, DQ6, and DQ7. Table 11 and the following subsections describe the function of these bits. DQ7 and DQ6 each offer a method for determining whether a program or erase operation is complete or in progress. The device also provides a hardware-based output signal, RY/BY#, to determine whether an Embedded Program or Erase operation is in progress or has been completed. valid data, the data outputs on DQ0–DQ6 may be still invalid. Valid data on DQ0–DQ7 will appear on successive read cycles. Table 11 shows the outputs for Data# Polling on DQ7. Figure 7 shows the Data# Polling algorithm. Figure 19 in “AC Characteristics” shows the Data# Polling timing diagram. DQ7: Data# Polling START The Data# Polling bit, DQ7, indicates to the host system whether an Embedded Program or Erase algorithm is in progress or completed, or whether the device is in Erase Suspend. Data# Polling is valid after the rising edge of the final WE# pulse in the command sequence. During the Embedded Program algorithm, the device outputs on DQ7 the complement of the datum programmed to DQ7. This DQ7 status also applies to programming during Erase Suspend. When the Embedded Program algorithm is complete, the device outputs the datum programmed to DQ7. The system must provide the program address to read valid status information on DQ7. If a program address falls within a protected sector, Data# Polling on DQ7 is active for approximately 1 µs, then the device returns to the read mode. Read DQ7–DQ0 Addr = VA DQ7 = Data? No No During the Embedded Erase algorithm, Data# Polling produces a “0” on DQ7. When the Embedded Erase algorithm is complete, or if the device enters the Erase Suspend mode, Data# Polling produces a “1” on DQ7. The system must provide an address within any of the sectors selected for erasure to read valid status information on DQ7. After an erase command sequence is written, if all sectors selected for erasing are protected, Data# Polling on DQ7 is active for approximately 100 µs, then the device returns to the read mode. If not all selected sectors are protected, the Embedded Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are protected. However, if the system reads DQ7 at an address within a protected sector, the status may not be valid. Just prior to the completion of an Embedded Program or Erase operation, DQ7 may change asynchronously with DQ0–DQ6 while Output Enable (OE#) is asserted low. That is, the device may change from providing status information to valid data on DQ7. Depending on when the system samples the DQ7 output, it may read the status or valid data. Even if the device has completed the program or erase operation and DQ7 has September 12, 2006 Yes DQ5 = 1? Yes Read DQ7–DQ0 Addr = VA DQ7 = Data? Yes No FAIL PASS Notes: 1. VA = Valid address for programming. During a sector erase operation, a valid address is any sector address within the sector being erased. During chip erase, a valid address is any non-protected sector address. 2. DQ7 should be rechecked even if DQ5 = “1” because DQ7 may change simultaneously with DQ5. Am29LV065MU Figure 8. Data# Polling Algorithm 35 D A T A RY/BY#: Ready/Busy# The RY/BY# is a dedicated, open-drain output pin which indicates whether an Embedded Algorithm is in progress or complete. The RY/BY# status is valid after the rising edge of the final WE# pulse in the command sequence. Since RY/BY# is an open-drain output, several RY/BY# pins can be tied together in parallel with a pull-up resistor to VCC. S H E E T Table 11 shows the outputs for Toggle Bit I on DQ6. Figure 8 shows the toggle bit algorithm. Figure 20 in the AC Characteristics shows the toggle bit timing diagrams. Figure 21 shows the differences between DQ2 and DQ6 in graphical form. See “DQ2: Toggle Bit II” on page 37.. If the output is low (Busy), the device is actively erasing or programming. (This includes programming in the Erase Suspend mode.) If the output is high (Ready), the device is in the read mode, the standby mode, or the device is in the erase-suspend-read mode. START Read DQ7–DQ0 Table 11 shows the outputs for RY/BY#. Read DQ7–DQ0 DQ6: Toggle Bit I Toggle Bit I on DQ6 indicates whether an Embedded Program or Erase algorithm is in progress or complete, or whether the device has entered the Erase Suspend mode. Toggle Bit I may be read at any address, and is valid after the rising edge of the final WE# pulse in the command sequence (prior to the program or erase operation), and during the sector erase time-out. During an Embedded Program or Erase algorithm operation, successive read cycles to any address cause DQ6 to toggle. The system may use either OE# or CE# to control the read cycles. When the operation is complete, DQ6 stops toggling. Toggle Bit = Toggle? Yes No If a program address falls within a protected sector, DQ6 toggles for approximately 1 μs after the program command sequence is written, then returns to reading array data. DQ5 = 1? Yes Read DQ7–DQ0 Twice After an erase command sequence is written, if all sectors selected for erasing are protected, DQ6 toggles for approximately 100 µs, then returns to reading array data. If not all selected sectors are protected, the Embedded Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are protected. The system can use DQ6 and DQ2 together to determine whether a sector is actively erasing or is erase-suspended. When the device is actively erasing (that is, the Embedded Erase algorithm is in progress), DQ6 toggles. When the device enters the Erase Suspend mode, DQ6 stops toggling. However, the system must also use DQ2 to determine which sectors are erasing or erase-suspended. Alternatively, the system can use DQ7 (See “DQ7: Data# Polling” on page 35.). No Toggle Bit = Toggle? No Yes Program/Erase Operation Not Complete, Write Reset Command Program/Erase Operation Complete Note: The system should recheck the toggle bit even if DQ5 = “1” because the toggle bit may stop toggling as DQ5 changes to “1.” See the subsections on DQ6 and DQ2 for more information. Figure 9. Toggle Bit Algorithm DQ6 also toggles during the erase-suspend-program mode, and stops toggling once the Embedded Program algorithm is complete. 36 Am29LV065MU September 12, 2006 D A T A DQ2: Toggle Bit II The “Toggle Bit II” on DQ2, when used with DQ6, indicates whether a particular sector is actively erasing (that is, the Embedded Erase algorithm is in progress), or whether that sector is erase-suspended. Toggle Bit II is valid after the rising edge of the final WE# pulse in the command sequence. DQ2 toggles when the system reads at addresses within those sectors that have been selected for erasure. (The system may use either OE# or CE# to control the read cycles.) But DQ2 cannot distinguish whether the sector is actively erasing or is erase-suspended. DQ6, by comparison, indicates whether the device is actively erasing, or is in Erase Suspend, but cannot distinguish which sectors are selected for erasure. Thus, both status bits are required for sector and mode information. Refer to Table 11 to compare outputs for DQ2 and DQ6. Figure 8 shows the toggle bit algorithm in flowchart form, and “DQ2: Toggle Bit II” explains the algorithm. Also, see “DQ6: Toggle Bit I” on page 36. Figure 20 shows the toggle bit timing diagram. Figure 21 shows the differences between DQ2 and DQ6 in graphical form. Reading Toggle Bits DQ6/DQ2 Refer to Figure 8 for the following discussion. Whenever the system initially begins reading toggle bit status, it must read DQ7–DQ0 at least twice in a row to determine whether a toggle bit is toggling. Typically, the system would note and store the value of the toggle bit after the first read. After the second read, the system would compare the new value of the toggle bit with the first. If the toggle bit is not toggling, the device has completed the program or erase operation. The system can read array data on DQ7–DQ0 on the following read cycle. However, if after the initial two read cycles, the system determines that the toggle bit is still toggling, the system also should note whether the value of DQ5 is high (See “DQ5: Exceeded Timing Limits” on page 37.). If it is, the system should then determine again whether the toggle bit is toggling, since the toggle bit may have stopped toggling just as DQ5 went high. If the toggle bit is no longer toggling, the device has successfully completed the program or erase operation. If it is still toggling, the device did not completed the operation successfully, and the system must write the reset command to return to reading array data. The remaining scenario is that the system initially determines that the toggle bit is toggling and DQ5 has not gone high. The system may continue to monitor September 12, 2006 S H E E T the toggle bit and DQ5 through successive read cycles, determining the status as described in the previous paragraph. Alternatively, it may choose to perform other system tasks. In this case, the system must start at the beginning of the algorithm when it returns to determine the status of the operation (top of Figure 8). DQ5: Exceeded Timing Limits DQ5 indicates whether the program, erase, or write-to-buffer time has exceeded a specified internal pulse count limit. Under these conditions DQ5 produces a “1,” indicating that the program or erase cycle was not successfully completed. The device may output a “1” on DQ5 if the system tries to program a “1” to a location that was previously programmed to “0.” Only an erase operation can change a “0” back to a “1.” Under this condition, the device halts the operation, and when the timing limit has been exceeded, DQ5 produces a “1.” In all these cases, the system must write the reset command to return the device to the reading the array (or to erase-suspend-read if the device was previously in the erase-suspend-program mode). DQ3: Sector Erase Timer After writing a sector erase command sequence, the system may read DQ3 to determine whether or not erasure has begun. (The sector erase timer does not apply to the chip erase command.) If additional sectors are selected for erasure, the entire time-out also applies after each additional sector erase command. When the time-out period is complete, DQ3 switches from a “0” to a “1.” If the time between additional sector erase commands from the system can be assumed to be less than 50 µs, the system need not monitor DQ3. Also, see “Sector Erase Command Sequence” on page 31. After the sector erase command is written, the system should read the status of DQ7 (Data# Polling) or DQ6 (Toggle Bit I) to ensure that the device has accepted the command sequence, and then read DQ3. If DQ3 is “1,” the Embedded Erase algorithm has begun; all further commands (except Erase Suspend) are ignored until the erase operation is complete. If DQ3 is “0,” the device will accept additional sector erase commands. To ensure the command has been accepted, the system software should check the status of DQ3 prior to and following each subsequent sector erase command. If DQ3 is high on the second status check, the last command might not have been accepted. Table 11 shows the status of DQ3 relative to the other status bits. Am29LV065MU 37 D A T A DQ1: Write-to-Buffer Abort DQ1 indicates whether a Write-to-Buffer operation was aborted. Under these conditions DQ1 produces a “1”. The system must issue the Write-to-Buffer-Abort-Reset command sequence to reTable 11. Standard Mode Program Suspend Mode Erase Suspend Mode Write-toBuffer S H E E T turn the device to reading array data. See “Write Buffer Programming” on page 27. for more details. Write Operation Status DQ7 Status ((Note 2)) Embedded Program Algorithm DQ7# Embedded Erase Algorithm 0 Program-Suspended Program- Sector Suspend Non-Program Read Suspended Sector Erase-Suspended 1 EraseSector Suspend Non-Erase Suspended Read Sector Erase-Suspend-Program DQ7# (Embedded Program) Busy ((Note 3)) DQ7# Abort ((Note 4)) DQ7# DQ6 Toggle Toggle No toggle DQ5 ((Note 1)) 0 0 DQ3 N/A 1 DQ2 ((Note 2)) No toggle Toggle DQ1 0 N/A RY/BY# 0 0 Invalid (not allowed) 1 Data 1 0 N/A Toggle N/A Data 1 1 Toggle 0 N/A N/A N/A 0 Toggle Toggle 0 0 N/A N/A N/A N/A 0 1 0 0 Notes: 1. DQ5 switches to ‘1’ when an Embedded Program, Embedded Erase, or Write-to-Buffer operation has exceeded the maximum timing limits. See “DQ5: Exceeded Timing Limits” on page 37. for more information. 2. DQ7 and DQ2 require a valid address when reading status information. See “DQ7: Data# Polling” on page 35. and “DQ2: Toggle Bit II” on page 37 for further details. 3. The Data# Polling algorithm should be used to monitor the last loaded write-buffer address location. 4. DQ1 switches to ‘1’ when the device has aborted the write-to-buffer operation. 38 Am29LV065MU September 12, 2006 D A T A S H E E T ABSOLUTE MAXIMUM RATINGS Storage Temperature Plastic Packages . . . . . . . . . . . . . . . –65°C to +150°C Ambient Temperature with Power Applied. . . . . . . . . . . . . . –55°C to +125°C Voltage with Respect to Ground VCC ((Note 1)) . . . . . . . . . . . . . . . . –0.5 V to +4.0 V 20 ns 20 ns +0.8 V –0.5 V –2.0 V VIO . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to +4.0 V 20 ns A9, OE#, ACC, and RESET# ((Note 2)) . . . . . . . . . . . . . . . . . . –0.5 V to +12.5 V Figure 10. Maximum Negative Overshoot Waveform All other pins ((Note 1)). . . . . –0.5 V to VCC +0.5 V Output Short Circuit Current ((Note 3)) . . . . . 200 mA Notes: 1. Minimum DC voltage on input or I/O pins is –0.5 V. During voltage transitions, input or I/O pins may overshoot V SS to –2.0 V for periods of up to 20 ns. Maximum DC voltage on input or I/O pins is VCC +0.5 V. See Figure 9. During voltage transitions, input or I/O pins may overshoot to VCC +2.0 V for periods up to 20 ns. See Figure 10. 20 ns VCC +2.0 V VCC +0.5 V 2.0 V 2. Minimum DC input voltage on pins A9, OE#, ACC, and RESET# is –0.5 V. During voltage transitions, A9, OE#, ACC, and RESET# may overshoot V SS to –2.0 V for periods of up to 20 ns. See Figure 9. Maximum DC input voltage on pin A9, OE#, ACC, and RESET# is +12.5 V which may overshoot to +14.0 V for periods up to 20 ns. 20 ns 20 ns Figure 11. Maximum Positive Overshoot Waveform 3. No more than one output may be shorted to ground at a time. Duration of the short circuit should not be greater than one second. Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational sections of this data sheet is not implied. Exposure of the device to absolute maximum rating conditions for extended periods may affect device reliability. OPERATING RANGES Industrial (I) Devices Ambient Temperature (TA) . . . . . . . . . –40°C to +85°C Supply Voltages VCC for standard voltage range . . . . . . . . . . 2.7–3.6 V VCC for regulated voltage range . . . . . . . . . . 3.0–3.6 V VIO (Note 2) . . . . . . . . . . . . . . . . . . . . . . . . 1.65–3.0 V Notes: 1. Operating ranges define those limits between which the functionality of the device is guaranteed. 2. See Ordering Information section for valid VCC/VIO range combinations. The I/Os cannot go to 3 V when VIO = 1.8V. September 12, 2006 Am29LV065MU 39 D A T A S H E E T DC CHARACTERISTICS CMOS Compatible Parameter Symbol Parameter Description Test Conditions Min Typ Max Unit ±1.0 µA ILI Input Load Current (Note 1) VIN = VSS to VCC, VCC = VCC max ILIT A9, ACC Input Load Current VCC = VCC max; A9 = 12.5 V 35 µA ILR Reset Leakage Current VCC = VCC max= 12.5 V 35 µA ILO Output Leakage Current VOUT = VSS to VCC, VCC = VCC max ±1.0 µA ICC1 VCC Active Read Current (Notes 1, 2) CE# = VIL, OE# = VIH ICC2 VCC Initial Page Read Current (1, 2) ICC3 VCC Intra-Page Read Current (1, 2) 5 MHz 15 20 1 MHz 15 20 CE# = VIL, OE# = VIH 30 50 mA CE# = VIL, OE# = VIH 10 20 mA ICC4 VCC Active Write Current (Notes 2, 3) CE# = VIL, OE# = VIH 50 60 mA ICC5 VCC Standby Current (Note 2) CE#, RESET# = VCC ± 0.3 V, WP# = VIH 1 5 µA ICC6 VCC Reset Current (Note 2) RESET# = VSS ± 0.3 V, WP# = VIH 1 5 µA ICC7 Automatic Sleep Mode (Notes 2, 4) VIH = VCC ± 0.3 V; VIL = VSS ± 0.3 V, WP# = VIH 1 5 µA VIL1 Input Low Voltage 1(Notes 5, 6) –0.5 0.8 V VIH1 Input High Voltage 1 (Notes 5, 6) 0.7 x VCC VCC + 0.5 V VIL2 Input Low Voltage 2 (Notes 5, 7) –0.5 0.3 x VIO V VIH2 Input High Voltage 2 (Notes 5, 7) 0.7 x VIO VIO + 0.5 V VHH Voltage for ACC Program Acceleration VCC = 2.7 –3.6 V 11.5 12.5 V VID Voltage for Autoselect and Temporary VCC = 2.7 –3.6 V Sector Unprotect 11.5 12.5 V VOL Output Low Voltage (Note 9) 0.15 x VIO V VOH1 VOH2 VLKO Output High Voltage IOL = 4.0 mA, VCC = VCC min = VIO mA IOH = –2.0 mA, VCC = VCC min = VIO 0.85 VIO V IOH = –100 µA, VCC = VCC min = VIO VIO–0.4 V Low VCC Lock-Out Voltage (Note 8) 2.3 2.5 V Notes: 1. The ICC current listed is typically less than 2 mA/MHz, with OE# at VIH. 2. 3. 4. 5. 6. 7. 8. 9. 40 Maximum ICC specifications are tested with VCC = VCCmax. ICC active while Embedded Erase or Embedded Program is in progress. Automatic sleep mode enables the low power mode when addresses remain stable for tACC + 30 ns. If VIO < VCC, maximum VIL for CE# and DQ I/Os is 0.3 VIO. If VIO < VCC, minimum VIH for CE# and DQ I/Os is 0.7 VIO. Maximum VIH for these connections is VIO + 0.3 V VCC voltage requirements. VIO voltage requirements. VCC = 3 V and VIO = 3 V or 1.8 V. When VIO is at 1.8 V, I/Os cannot operate at 3 V. Not 100% tested. Includes RY/BY# pin. Am29LV065MU September 12, 2006 D A T A S H E E T TEST CONDITIONS Table 12. 3.3 V Test Condition 2.7 kΩ Device Under Test CL Test Specifications 6.2 kΩ All Speeds Output Load 1 TTL gate Output Load Capacitance, CL (including jig capacitance) 30 pF Input Rise and Fall Times 5 ns 0.0–3.0 V Input timing measurement reference levels (See Note) 1.5 V Output timing measurement reference levels 0.5 VIO V Input Pulse Levels Note: Diodes are IN3064 or equivalent Figure 12. Test Setup Unit Note: If VIO < VCC, the reference level is 0.5 VIO. KEY TO SWITCHING WAVEFORMS WAVEFORM INPUTS OUTPUTS Steady Changing from H to L Changing from L to H 3.0 V Input Don’t Care, Any Change Permitted Changing, State Unknown Does Not Apply Center Line is High Impedance State (High Z) 1.5 V Measurement Level 0.5 VIO V Output 0.0 V Note: If VIO < VCC, the input measurement reference level is 0.5 VIO. Figure 13. Input Waveforms and Measurement Levels September 12, 2006 Am29LV065MU 41 D A T A S H E E T AC CHARACTERISTICS Read-Only Operations Parameter Speed Options JEDE C Std. Description 90R 101, 101R Min 90 100 110 120 ns CE#, OE# = VIL Max 90 100 110 120 ns OE# = VIL Max 90 100 110 120 ns Max 25 30 30 40 30 40 ns Max 25 30 30 40 30 40 ns Test Setup tAVAV tRC Read Cycle Time (Note 1) tAVQV tACC Address to Output Delay tELQV tCE Chip Enable to Output Delay tPACC Page Access Time 112R 112 120R 120 Unit tGLQV tOE Output Enable to Output Delay tEHQZ tDF Chip Enable to Output High Z (Note 1) Max 25 ns tGHQZ tDF Output Enable to Output High Z (Note 1) Max 25 ns tAXQX tOH Output Hold Time From Addresses, CE# or OE#, Whichever Occurs First Min 0 ns Read Min 0 ns Toggle and Data# Polling Min 10 ns Output Enable tOEH Hold Time (Note 1) Notes: 1. Not 100% tested. 2. See Figure 11 and Table 12 for test specifications. 3. AC specifications listed are tested with VIO = VCC. Contact AMD for more information on AC Operation with VIO ≠VCC. tRC Addresses Stable Addresses tACC CE# tRH tRH tDF tOE OE# tOEH WE# tCE tOH HIGH Z HIGH Z Output Valid Outputs RESET# RY/BY# 0V Figure 14. 42 Read Operation Timings Am29LV065MU September 12, 2006 D A T A S H E E T AC CHARACTERISTICS Same Page A22-A3 A2-A0 Aa Ab tPACC tACC Data Bus Qa Ad Ac tPACC Qb tPACC Qc Qd CE# OE# Figure 15. September 12, 2006 Page Read Timings Am29LV065MU 43 D A T A S H E E T AC CHARACTERISTICS Hardware Reset (RESET#) Parameter JEDEC Std Description All Speed Options Unit tReady RESET# Pin Low (During Embedded Algorithms) to Read Mode (See Note) Max 20 μs tReady RESET# Pin Low (NOT During Embedded Algorithms) to Read Mode (See Note) Max 500 ns tRP RESET# Pulse Width Min 500 ns tRH Reset High Time Before Read (See Note) Min 50 ns tRPD RESET# Low to Standby Mode Min 20 μs tRB RY/BY# Recovery Time Min 0 ns Note: Not 100% tested. RY/BY# CE#, OE# tRH RESET# tRP tReady Reset Timings NOT during Embedded Algorithms Reset Timings during Embedded Algorithms tReady RY/BY# tRB CE#, OE# RESET# tRP Figure 16. 44 Reset Timings Am29LV065MU September 12, 2006 D A T A S H E E T AC CHARACTERISTICS Erase and Program Operations Parameter Speed Options 101, 112, 120, 90R 101R 112R 120R Unit JEDEC Std. Description tAVAV tWC Write Cycle Time (Note 1) Min tAVWL tAS Address Setup Time Min 0 ns tASO Address Setup Time to OE# low during toggle bit polling Min 15 ns tAH Address Hold Time Min 45 ns tAHT Address Hold Time From CE# or OE# high during toggle bit polling Min 0 ns tDVWH tDS Data Setup Time Min 45 ns tWHDX tDH Data Hold Time Min 0 ns Min 20 ns Read Recovery Time Before Write (OE# High to WE# Low) Min 0 ns tWLAX tOEPH Output Enable High during toggle bit polling 90 100 110 120 ns tGHWL tGHWL tELWL tCS CE# Setup Time Min 0 ns tWHEH tCH CE# Hold Time Min 0 ns tWLWH tWP Write Pulse Width Min 35 ns tWHDL tWPH Write Pulse Width High Min 30 ns Write Buffer Program Operation (Note 2), (Note 3) Typ 352 µs Effective Byte Program Time, using the Write Buffer (Note 2), (Note 4) Typ 11 µs Effective Accelerated Byte Program Time, using the Write Buffer (Notes (Note 2), (Note 4) Typ 8.8 µs Single Byte Program Operation (Note 2), (Note 5) Typ 100 µs Accelerated Single Byte Programming Operation (Note 2), (Note 5) Typ 90 µs tWHWH2 tWHWH2 Sector Erase Operation (Note 2) Typ 0.5 sec tVHH VHH Rise and Fall Time (Note 1) Min 250 ns tVCS VCC Setup Time (Note 1) Min 50 µs tRB Write Recovery Time from RY/BY# Min 0 ns tWHWH1 tWHWH1 tBUSY WE# High to RY/BY# Low Max 90 tPOLL Program Valid Before Status Polling (Note 7) Max 100 110 4 120 ns µs Notes: 1. Not 100% tested. 2. See the “Erase And Programming Performance” section for more information. 3. For 1–32 bytes programmed. 4. Effective write buffer specification is based upon a 32-byte write buffer operation. 5. five Byte programming specification is based upon a single byte programming operation not utilizing the write buffer. 6. AC specifications listed are tested with VIO = VCC. Contact AMD for information on AC operation with VIO 7. command is issued within tPOLL, tPOLL must be fully re-applied upon resuming the programming operation. If the suspend command is issued after tPOLL, tPOLL is not required again prior to reading the status bits upon resuming. ≠ VCC. When using the program suspend/resume feature, if the suspend September 12, 2006 Am29LV065MU 45 D A T A S H E E T AC CHARACTERISTICS Program Command Sequence (last two cycles) tAS tWC Addresses Read Status Data (last two cycles) 555h PA PA PA tAH CE# tCH OE# tPOLL tWP WE# tWPH tCS tDS tDH PD A0h Data tWHWH1 Status tBUSY DOUT tRB RY/BY# VCC tVCS Notes:. PA = program address, PD = program data, DOUT is the true data at the program address. Figure 17. Program Operation Timings VHH ACC VIL or VIH VIL or VIH tVHH tVHH Figure 18. 46 Accelerated Program Timing Diagram Am29LV065MU September 12, 2006 D A T A S H E E T AC CHARACTERISTICS Erase Command Sequence (last two cycles) tAS tWC XXXh Addresses Read Status Data VA SA VA XXXh for chip erase tAH CE# tCH OE# tWP WE# tWPH tCS tWHWH2 tDS tDH Data 55h In Progress 30h Complete 10 for Chip Erase tBUSY tRB RY/BY# tVCS VCC Notes: SA = sector address (for Sector Erase), VA = Valid Address for reading status data (see “Write Operation Status”) Figure 19. September 12, 2006 Chip/Sector Erase Operation Timings Am29LV065MU 47 D A T A S H E E T AC CHARACTERISTICS tRC Addresses VA tPOLL VA VA tACC tCE CE# tCH tOE OE# tOEH tDF WE# tOH DQ15 and DQ7 DQ14–DQ8, DQ6–DQ0 Complement Complement Status Data Status Data True True Valid Data Valid Data High Z High Z tBUSY RY/BY# Note: VA = Valid address. Illustration shows first status cycle after command sequence, last status read cycle, and array data read cycle. Figure 20. Data# Polling Timings (During Embedded Algorithms) 48 Am29LV065MU September 12, 2006 D A T A S H E E T AC CHARACTERISTICS tAHT tAS Addresses tAHT tASO CE# tCEPH tOEH WE# tOEPH OE# tDH DQ6/DQ2 tOE Valid Status Valid Status Valid Status (first read) (second read) (stops toggling) Valid Data Valid Data RY/BY# Note: VA = Valid address; not required for DQ6. Illustration shows first two status cycle after command sequence, last status read cycle, and array data read cycle Figure 21. Toggle Bit Timings (During Embedded Algorithms) Enter Embedded Erasing WE# Erase Suspend Erase Enter Erase Suspend Program Erase Suspend Read Erase Suspend Program Erase Resume Erase Suspend Read Erase Erase Complete DQ6 DQ2 Note: DQ2 toggles only when read at an address within an erase-suspended sector. The system may use OE# or CE# to toggle DQ2 and DQ6. Figure 22. September 12, 2006 DQ2 vs. DQ6 Am29LV065MU 49 D A T A S H E E T AC CHARACTERISTICS Temporary Sector Unprotect Parameter JEDEC Std Description All Speed Options Unit tVIDR VID Rise and Fall Time (See Note) Min 500 ns tRSP RESET# Setup Time for Temporary Sector Unprotect Min 4 µs tRRB RESET# Hold Time from RY/BY# High for Temporary Sector Group Unprotect Min 4 µs Note: Not 100% tested. VID RESET# VID VSS, VIL, or VIH VSS, VIL, or VIH tVIDR tVIDR Program or Erase Command Sequence CE# WE# tRRB tRSP RY/BY# Figure 23. 50 Temporary Sector Group Unprotect Timing Diagram Am29LV065MU September 12, 2006 D A T A S H E E T AC CHARACTERISTICS VID VIH RESET# SA, A6, A1, A0 Valid* Valid* Sector Group Protect or Unprotect Data 60h 60h Valid* Verify 40h Status Sector Group Protect: 150 µs, Sector Group Unprotect: 15 ms 1 µs CE# WE# OE# * For sector group protect, A6:A0 = 0xx0010. For sector group unprotect, A6:A0 = 1xx0010. Figure 24. September 12, 2006 Sector Group Protect and Unprotect Timing Diagram Am29LV065MU 51 D A T A S H E E T AC CHARACTERISTICS Alternate CE# Controlled Erase and Program Operations Parameter Speed Options 90R 101, 101R 112, 112R 120, 120R Unit 90 100 110 120 ns JEDEC Std. Description tAVAV tWC Write Cycle Time (Note Notes 1) Min tAVWL tAS Address Setup Time Min 0 ns tELAX tAH Address Hold Time Min 45 ns tDVEH tDS Data Setup Time Min 45 ns tEHDX tDH Data Hold Time Min 0 ns tGHEL tGHEL Read Recovery Time Before Write (OE# High to WE# Low) Min 0 ns tWLEL tWS WE# Setup Time Min 0 ns tEHWH tWH WE# Hold Time Min 0 ns tELEH tCP CE# Pulse Width Min 45 ns tEHEL tCPH CE# Pulse Width High Min 30 ns Write Buffer Program Operation (Notes Notes 2, Notes 3) Typ 352 µs Effective Byte Program Time, using the Write Buffer (Notes Notes 2, Notes 4) Typ 11 µs Effective Accelerated Byte Program Time, using the Write Buffer (Notes Notes 2, Notes 4) Typ 8.8 µs Single Byte Program Operation (Note Notes 2, Notes 5) Typ 100 µs Accelerated Single Byte Programming Operation (Note Notes 2, Notes 5) Typ 90 µs tWHWH2 Sector Erase Operation (Note Notes 2) Typ 0.5 sec tRH RESET # High Time Before Write (Note Notes 1) Min 50 ns Program Valid Before Status Polling (Note Notes 7) Max 4 µs tWHWH1 tWHWH2 tWHWH1 tPOLL Notes: 1. Not 100% tested. 2. See the “Erase And Programming Performance” section for more information. 3. For 1–32 bytes programmed. 4. Effective write buffer specification is based upon a 32-byte write buffer operation. 5. Byte programming specification is based upon a single byte programming operation not utilizing the write buffer. 6. AC specifications listed are tested with VIO = VCC. Contact AMD for information on AC operation with VIO ≠ VCC. 7. When using the program suspend/resume feature, if the suspend command is issued within tPOLL, tPOLL must be fully re-applied upon resuming the programming operation. If the suspend command is issued after tPOLL, tPOLL is not required again prior to reading the status bits upon resuming. 52 Am29LV065MU September 12, 2006 D A T A S H E E T AC CHARACTERISTICS 555 for program 2AA for erase PA for program SA for sector erase 555 for chip erase Data# Polling Addresses PA tWC tAS tAH tWH WE# tPOLL tGHEL OE# tWHWH1 or 2 tCP CE# tWS tCPH tBUSY tDS tDH DQ7#, DQ15 Data tRH DOUT A0A0 for program PD for program 5555 for erase 3030 for sector erase 1010 for chip erase RESET# RY/BY# Notes: 1. Figure indicates last two bus cycles of a program or erase operation. 2. PA = program address, SA = sector address, PD = program data. 3. DQ7# is the complement of the data written to the device. DOUT is the data written to the device. Figure 25. September 12, 2006 Alternate CE# Controlled Write (Erase/Program) Operation Timings Am29LV065MU 53 D A T A S H E E T ERASE AND PROGRAMMING PERFORMANCE Parameter Typ (Note 1) Max (Note 2) Unit Comments Sector Erase Time 0.5 15 sec Chip Erase Time 64 128 sec Excludes 00h programming prior to erasure (Note 5) Effective Byte Program Time, using the Write Buffer (Note 3) 11 57 µs Effective Accelerated Byte Program Time, using the Write Buffer (Note 3) 8.8 49 µs Single Byte Program Time 100 800 µs Accelerated Single Byte Program Time (Note 4) 90 720 µs Chip Program Time, using the Write Buffer 92 170 sec Excludes system level overhead (Note 6) Notes: 1. Typical program and erase times assume the following conditions: 25°C, 3.0 V VCC, 100,000 cycles. Additionally, programming typicals assume checkerboard pattern. Under worst case conditions of 90°C, VCC = 3.0 V, 100,000 cycles. Effective write buffer specification is based upon a 32–byte write buffer operation. Byte programming specification is based upon a single byte programming operation not utilizing the write buffer. In the pre-programming step of the Embedded Erase algorithm, all bits are programmed to 00h before erasure. System-level overhead is the time required to execute the two- or four-bus-cycle sequence for the program command. See Table 10 for further information on command definitions. 7. The device has a minimum erase and program cycle endurance of 100,000 cycles. 2. 3. 4. 5. 6. LATCHUP CHARACTERISTICS Description Min Max Input voltage with respect to VSS on all pins except I/O pins (including A9, OE#, and RESET#) –1.0 V 12.5 V Input voltage with respect to VSS on all I/O pins –1.0 V VCC + 1.0 V –100 mA +100 mA VCC Current Note: Includes all pins except VCC. Test conditions: VCC = 3.0 V, one pin at a time. 54 Am29LV065MU September 12, 2006 D A T A S H E E T TSOP PIN AND BGA PACKAGE CAPACITANCE Parameter Symbol Parameter Description Test Setup CIN Input Capacitance VIN = 0 COUT Output Capacitance VOUT = 0 CIN2 Control Pin Capacitance VIN = 0 Typ Max Unit TSOP 6 7.5 pF BGA 4.2 5.0 pF TSOP 8.5 12 pF BGA 5.4 6.5 pF TSOP 7.5 9 pF BGA 3.9 4.7 pF Notes: 1. Sampled, not 100% tested. 2. Test conditions TA = 25°C, f = 1.0 MHz. DATA RETENTION Parameter Description Test Conditions Min Unit 150°C 10 Years 125°C 20 Years Minimum Pattern Data Retention Time September 12, 2006 Am29LV065MU 55 D A T A S H E E T PHYSICAL DIMENSIONS TS 048—48-Pin Standard Thin Small Outline Package Dwg rev AA; 10/99 56 Am29LV065MU September 12, 2006 D A T A S H E E T PHYSICAL DIMENSIONS TSR048—48-Pin Reverse Thin Small Outline Package Dwg rev AA; 10/99 September 12, 2006 Am29LV065MU 57 D A T A S H E E T PHYSICAL DIMENSIONS FBE063—63-Ball Fine-Pitch Ball Grid Array, 12 x 11 mm Package Dwg rev AF; 10/99 58 Am29LV065MU September 12, 2006 D A T A S H E E T REVISION SUMMARY Revision A (August 3, 2001) Revision B+2 (September 10, 2002) Initial release as abbreviated Advance Information data sheet. Product Selector Guide Added Note 2. Revision A+1 (October 3, 2001) Ordering Information Global Added Note 1. Added 120 ns device, changed 100 ns, VIO = 1.65–2.7 V device to 110 ns, changed 90 ns operating range to 3.0–3.6 V. Physical Dimensions Sector Erase Command Sequence Deleted statement that describes the outcome of when the Embedded Erase operation is in progress. Added section. Revision B+3 (November 7, 2002) Revision B (April 26, 2002) Product Selector Guide and Read Only Operations Expanded data sheet to full specification version. Changed the page access times and TOE Revision B+1 (August 9, 2002) Customer Lockable: SecSi Sector NOT Programmed or Protected at the factory. MIRRORBIT 64 MBIT Device Family Added 64 Fortified BGA to LV640MU device. Added second bullet, SecSi sector-protect verify text and figure 3. Alternate CE# Controlled Erase and Program Operations SecSi Sector Flash Memory Region, and Enter SecSi Sector/Exit SecSi Sector Command Sequence Added tRH parameter to table. Noted that the ACC function and unlock bypass modes are not available when the SecSi sector is enabled. Erase and Program Operations Byte/Word Program Command Sequence, Sector Erase Command Sequence, and Chip Erase Command Sequence Added tBUSY parameter to table. Figure 16. Program Operation Timings Added RY/BY# to waveform. Noted that the SecSi Sector, autoselect, and CFI functions are unavailable when a program or erase operation is in progress.” TSOP and BGA PIN Capacitance Added the FBGA package. Common Flash Memory Interface (CFI) Program Suspend/Program Resume Command Sequence Changed 15 μs typical to maximum and added 5 μs typical. Erase Suspend/Erase Resume Commands Changed typical from 20 μs to 5 μs and added a maximum of 20 μs. Changed wording in last sentence of third paragraph from, “...the autoselect mode.” to “...reading array data.” Changed CFI website address. Revision B+4 (February 17, 2003) Distinctive Characteristics Corrected performance characteristics. Special package handling instructions Modified the special handling wording. Product Selector Guide DC Characteristics table Removed 90R speed option. Deleted the IACC specification row. Added note 2. CFI Ordering Information Changed text in the third paragraph of CFI to read “reading array data.” Corrected Valid Combination to reflect speed option changes. Added Note. September 12, 2006 Am29LV065MU 59 D A T A S H E E T AC Characteristics - Erase and Program Operations AC Characteristics Added Note Input values in the tWHWH1 and tWHWH2 parameters in the Erase and Program Options table that were previously TBD. Also added notes 5 and 6. Added tPOLL information. Added note. Trademarks Input values in the tWHWH1 and tWHWH2 parameters in the Alternate CE# Controlled Erase and Program Options table that were previously TBD. Also added notes 5. Updated. Erase and Programming Performance Added Max programming specifications. Input values into table that were previously TBD. Added notation referencing superseding documentation. Added note 4. ESN. Revision C + 1 (August 23, 2004) Revision C + 2 (November 9, 2004) SecSi (Secured Silicon) Sector Flash Memory Region Added Pb-free options. Corrected SecSi Sector address range in table. Revision C + 3 (December 13, 2005) Corrected the address to find the 16–byte random ESN. This product has been retired and is not available for designs. For new and current designs, S29GL064A supersedes Am29LV065MU and is the factory-recomm e n d e d m i g r a t i o n p a t h . P l e a s e r e fe r t o t h e S29GL064A datasheet for specifications and ordering information. Availability of this document is retained for reference and historical purposes only. Revision C (February 17, 2004) Table 1 Device Bus Operations Modified ACC column to replace instances of X to L/H. Table 10: Command Definitions Trademark updated. Replaced the Addr information for both Program/Erase Suspend and Program/Erase Resume from BA to XXX. Revision C4 (September 12, 2006) DC Characteristics - CMOS Compatible Changed tBUSY to a maximum specification. Erase and Program Operations table Removed additional sentence from note 4. Erase Suspend/Erase Resume Commands Added note on flash device performance during suspend/erase mode. Colophon The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for any use that includes fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for any use where chance of failure is intolerable (i.e., submersible repeater and artificial satellite). Please note that Spansion Inc. will not be liable to you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Law of Japan, the US Export Administration Regulations or the applicable laws of any other country, the prior authorization by the respective government entity will be required for export of those products. Trademarks Copyright © 2001–2005 Advanced Micro Devices, Inc. All rights reserved. AMD, the AMD logo, and combinations thereof are registered trademarks of Advanced Micro Devices, Inc. ExpressFlash is a trademark of Advanced Micro Devices, Inc. Product names used in this publication are for identification purposes only and may be trademarks of their respective companies. Copyright © 2006 Spansion Inc. All Rights Reserved. Spansion, the Spansion logo, MirrorBit, ORNAND, HD-SIM, and combinations thereof are trademarks of Spansion Inc. Other names are for informational purposes only and may be trademarks of their respective owners. 60 Am29LV065MU September 12, 2006