CY7C64713/14 EZ-USB FX1™ USB Microcontroller Full-speed USB Peripheral Controller Features • Single-chip integrated USB transceiver, SIE, and enhanced 8051 microprocessor • Fit, form and function upgradable to the FX2LP (CY7C68013A) — Pin-compatible — Object-code-compatible — Functionally-compatible (FX1 functionality is a Subset of the FX2LP) • Draws no more than 65 mA in any mode making the FX1 suitable for bus powered applications • Software: 8051 runs from internal RAM, which is: — Downloaded via USB — Loaded from EEPROM — External memory device (128-pin configuration only) • 16 KBytes of on-chip Code/Data RAM • Four programmable BULK/INTERRUPT/ISOCHRONOUS endpoints — Buffering options: double, triple, and quad • Additional programmable (BULK/INTERRUPT) 64-byte endpoint • 8- or 16-bit external data interface • Smart Media Standard ECC generation • GPIF — Allows direct connection to most parallel interfaces; 8- and 16-bit — Programmable waveform descriptors and configuration registers to define waveforms • • • • • • • • • • High-performance micro using standard tools with lower-power options 24 MHz Ext. XTAL x20 PLL /0.5 /1.0 /2.0 Data (8) Address (16) FX1 VCC • 8051 Core 12/24/48 MHz, four clocks/cycle 1.5k connected for enumeration D+ USB D– — Supports multiple Ready (RDY) inputs and Control (CTL) outputs Integrated, industry standard 8051 with enhanced features — Up to 48-MHz clock rate — Four clocks per instruction cycle — Two USARTS — Three counter/timers — Expanded interrupt system — Two data pointers 3.3V operation with 5V tolerant inputs Smart SIE Vectored USB interrupts Separate data buffers for the Setup and DATA portions of a CONTROL transfer Integrated I2C controller, runs at 100 or 400 KHz 48-MHz, 24-MHz, or 12-MHz 8051 operation Four integrated FIFOs — Brings glue and FIFOs inside for lower system cost — Automatic conversion to and from 16-bit buses — Master or slave operation — FIFOs can use externally supplied clock or asynchronous strobes — Easy interface to ASIC and DSP ICs Vectored for FIFO and GPIF interrupts Up to 40 general purpose I/Os Three package options—128-pin TQFP, 100-pin TQFP, and 56-pin QFN Lead-free XCVR CY Smart 16 KB RAM I2C Address (16) / Data Bus (8) 1.0 Master Abundant I/O including two USARTS Additional I/Os (24) ADDR (9) GPIF RDY (6) CTL (6) ECC USB Engine Integrated full-speed XCVR 4 kB FIFO Enhanced USB core Simplifies 8051 code “Soft Configuration” Easy firmware changes 8/16 General programmable I/F to ASIC/DSP or bus standards such as ATAPI, EPP, etc. Up to 96 MBytes/s burst rate FIFO and endpoint memory (master or slave operation) Figure 1-1. Block Diagram Cypress Semiconductor Corporation Document #: 38-08039 Rev. *B • 3901 North First Street • San Jose, CA 95134 • 408-943-2600 Revised February 14, 2005 CY7C64713/14 2.0 4.2 Functional Description EZ-USB FX1 (CY7C64713/4) is a full-speed highly integrated, USB microcontroller. By integrating the USB transceiver, serial interface engine (SIE), enhanced 8051 microcontroller, and a programmable peripheral interface in a single chip, Cypress has created a very cost-effective solution that provides superior time-to-market advantages. Because it incorporates the USB transceiver, the EZ-USB FX1 is more economical, providing a smaller footprint solution than USB SIE or external transceiver implementations. With EZ-USB FX1, the Cypress Smart SIE handles most of the USB protocol in hardware, freeing the embedded microcontroller for application-specific functions and decreasing development time to ensure USB compatibility. The General Programmable Interface (GPIF) and Master/ Slave Endpoint FIFO (8- or 16-bit data bus) provides an easy and glueless interface to popular interfaces such as ATA, UTOPIA, EPP, PCMCIA, and most DSP/processors. Three lead-free packages are defined for the family: 56 QFN, 100 TQFP, and 128 TQFP. 3.0 Applications • DSL modems • ATA interface • Memory card readers • Legacy conversion devices • Home PNA • Wireless LAN • MP3 players • Networking The “Reference Designs” section of the cypress website provides additional tools for typical USB applications. Each reference design comes complete with firmware source and object code, schematics, and documentation. Please visit http://www.cypress.com for more information. 8051 Microprocessor The 8051 microprocessor embedded in the FX1 family has 256 bytes of register RAM, an expanded interrupt system, three timer/counters, and two USARTs. 4.2.1 8051 Clock Frequency FX1 has an on-chip oscillator circuit that uses an external 24MHz (±100 ppm) crystal with the following characteristics: • Parallel resonant • Fundamental mode • 500-µW drive level • 12-pF (5% tolerance) load capacitors. An on-chip PLL multiplies the 24-MHz oscillator up to 480 MHz, as required by the transceiver/PHY, and internal counters divide it down for use as the 8051 clock. The default 8051 clock frequency is 12 MHz. The clock frequency of the 8051 can be changed by the 8051 through the CPUCS register, dynamically. The CLKOUT pin, which can be three-stated and inverted using internal control bits, outputs the 50% duty cycle 8051 clock, at the selected 8051 clock frequency—48, 24, or 12 MHz. 4.2.2 USARTS FX1 contains two standard 8051 USARTs, addressed via Special Function Register (SFR) bits. The USART interface pins are available on separate I/O pins, and are not multiplexed with port pins. UART0 and UART1 can operate using an internal clock at 230 KBaud with no more than 1% baud rate error. 230-KBaud operation is achieved by an internally derived clock source that generates overflow pulses at the appropriate time. The internal clock adjusts for the 8051 clock rate (48, 24, 12 MHz) such that it always presents the correct frequency for 230KBaud operation.[1] 4.2.3 Special Function Registers Certain 8051 SFR addresses are populated to provide fast access to critical FX1 functions. These SFR additions are shown in Table 4-1. Bold type indicates non-standard, 4.1 USB Signaling Speed enhanced 8051 registers. The two SFR rows that end with “0” and “8” contain bit-addressable registers. The four I/O ports FX1 operates at one of the three rates defined in the USB A–D use the SFR addresses used in the standard 8051 for Specification Revision 2.0, dated April 27, 2000: ports 0–3, which are not implemented in FX1. Because of the • Full speed, with a signaling bit rate of 12 Mbps. faster and more efficient SFR addressing, the FX1 I/O ports are not addressable in external RAM space (using the MOVX FX1 does not support the low-speed signaling mode of 1.5 instruction). Mbps or the high-speed mode of 480 Mbps. C1 24 MHz C2 4.0 Functional Overview 12 pf 12 pf 20 × PLL 12-pF capacitor values assumes a trace capacitance of 3 pF per side on a four-layer FR4 PCA Figure 4-1. Crystal Configuration Note: 1. 115-KBaud operation is also possible by programming the 8051 SMOD0 or SMOD1 bits to a “1” for UART0 and/or UART1, respectively. Document #: 38-08039 Rev. *B Page 2 of 50 CY7C64713/14 I2C Bus 4.3 4.4 FX1 supports the I2C bus as a master only at 100/400 KHz. SCL and SDA pins have open-drain outputs and hysteresis inputs. These signals must be pulled up to 3.3V, even if no I2C device is connected. Buses All packages: 8- or 16-bit “FIFO” bidirectional data bus, multiplexed on I/O ports B and D. 128-pin package: adds 16-bit output-only 8051 address bus, 8-bit bidirectional data bus. Table 4-1. Special Function Registers x 8x 9x Ax Bx Cx Dx Ex Fx 0 IOA 1 SP IOB IOC IOD SCON1 PSW ACC B EXIF INT2CLR IOE SBUF1 2 DPL0 MPAGE 3 DPH0 INT4CLR OEA OEB 4 DPL1 OEC 5 DPH1 OED 6 DPS OEE 7 PCON EICON EIE EIP 8 TCON SCON0 9 TMOD SBUF0 IE IP A TL0 B TL1 AUTOPTRH1 EP2468STAT EP01STAT RCAP2L AUTOPTRL1 EP24FIFOFLGS GPIFTRIG RCAP2H EP68FIFOFLGS GPIFSGLDATH TH2 C TH0 reserved D TH1 AUTOPTRH2 E CKCON AUTOPTRL2 F 4.5 reserved I2C During the power-up sequence, internal logic checks the port for the connection of an EEPROM whose first byte is either 0xC0 or 0xC2. If found, it uses the VID/PID/DID values in the EEPROM in place of the internally stored values (0xC0), or it boot-loads the EEPROM contents into internal RAM (0xC2). If no EEPROM is detected, FX1 enumerates using internally stored descriptors. The default ID values for FX1 are VID/PID/DID (0x04B4, 0x6473, 0xAxxx where xxx=Chip revision).[2] Table 4-2. Default ID Values for FX1 Default VID/PID/DID Vendor ID 0x04B4 Cypress Semiconductor Product ID 0x6473 EZ-USB FX1 4.6 TL2 GPIFSGLDATLX AUTOPTRSETUP USB Boot Methods Device release T2CON 0xAnnn Depends chip revision (nnn = chip revision where first silicon = 001) ReNumeration™ Because the FX1’s configuration is soft, one chip can take on the identities of multiple distinct USB devices. When first plugged into USB, the FX1 enumerates automatically and downloads firmware and USB descriptor tables over the USB cable. Next, the FX1 enumerates again, this time as GPIFSGLDATLNOX a device defined by the downloaded information. This patented two-step process, called ReNumeration, happens instantly when the device is plugged in, with no hint that the initial download step has occurred. Two control bits in the USBCS (USB Control and Status) register control the ReNumeration process: DISCON and RENUM. To simulate a USB disconnect, the firmware sets DISCON to 1. To reconnect, the firmware clears DISCON to 0. Before reconnecting, the firmware sets or clears the RENUM bit to indicate whether the firmware or the Default USB Device will handle device requests over endpoint zero: if RENUM = 0, the Default USB Device will handle device requests; if RENUM = 1, the firmware will. 4.7 Bus-powered Applications The FX1 fully supports bus-powered designs by enumerating with less than 100 mA as required by the USB specification. 4.8 Interrupt System 4.8.1 INT2 Interrupt Request and Enable Registers FX1 implements an autovector feature for INT2 and INT4. There are 27 INT2 (USB) vectors, and 14 INT4 (FIFO/GPIF) vectors. See EZ-USB Technical Reference Manual (TRM) for more details. Note: 2. The I2C bus SCL and SDA pins must be pulled up, even if an EEPROM is not connected. Otherwise this detection method does not work properly. Document #: 38-08039 Rev. *B Page 3 of 50 CY7C64713/14 4.8.2 USB-Interrupt Autovectors The main USB interrupt is shared by 27 interrupt sources. To save the code and processing time that normally would be required to identify the individual USB interrupt source, the FX1 provides a second level of interrupt vectoring, called Autovectoring. When a USB interrupt is asserted, the FX1 pushes the program counter onto its stack then jumps to address 0x0043, where it expects to find a “jump” instruction to the USB Interrupt service routine. The FX1 jump instruction is encoded as shown in Table 4-3. If Autovectoring is enabled (AV2EN = 1 in the INTSETUP register), the FX1 substitutes its INT2VEC byte. Therefore, if the high byte (“page”) of a jump-table address is preloaded at location 0x0044, the automatically-inserted INT2VEC byte at 0x0045 will direct the jump to the correct address out of the 27 addresses within the page. 4.8.3 FIFO/GPIF Interrupt (INT4) Just as the USB Interrupt is shared among 27 individual USBinterrupt sources, the FIFO/GPIF interrupt is shared among 14 individual FIFO/GPIF sources. The FIFO/GPIF Interrupt, like the USB Interrupt, can employ autovectoring. Table 4-4 shows the priority and INT4VEC values for the 14 FIFO/GPIF interrupt sources. Table 4-3. INT2 USB Interrupts USB INTERRUPT TABLE FOR INT2 Priority INT2VEC Value 1 00 SUDAV Source Notes 2 04 SOF Start of Frame 3 08 SUTOK Setup Token Received 4 0C SUSPEND USB Suspend request 5 10 USB RESET Bus reset Setup Data Available 6 14 7 18 reserved 8 1C 9 20 EP0-IN 10 24 EP0-OUT EP0-OUT has USB data 11 28 EP1-IN EP1-IN ready to be loaded with data 12 2C EP1-OUT EP1-OUT has USB data 13 30 EP2 IN: buffer available. OUT: buffer has data 14 34 EP4 IN: buffer available. OUT: buffer has data 15 38 EP6 IN: buffer available. OUT: buffer has data 16 3C EP8 IN: buffer available. OUT: buffer has data 17 40 IBN IN-Bulk-NAK (any IN endpoint) EP0ACK FX1 ACK’d the CONTROL Handshake reserved EP0-IN ready to be loaded with data 18 44 19 48 reserved 20 4C EP1PING EP1 OUT was Pinged and it NAK’d 21 50 EP2PING EP2 OUT was Pinged and it NAK’d EP0PING EP0 OUT was Pinged and it NAK’d 22 54 EP4PING EP4 OUT was Pinged and it NAK’d 23 58 EP6PING EP6 OUT was Pinged and it NAK’d 24 5C EP8PING EP8 OUT was Pinged and it NAK’d 25 60 ERRLIMIT Bus errors exceeded the programmed limit 26 64 27 68 28 6C 29 70 EP2ISOERR ISO EP2 OUT PID sequence error 30 74 EP4ISOERR ISO EP4 OUT PID sequence error 31 78 EP6ISOERR ISO EP6 OUT PID sequence error 32 7C EP8ISOERR ISO EP8 OUT PID sequence error Document #: 38-08039 Rev. *B reserved reserved Page 4 of 50 CY7C64713/14 Table 4-4. Individual FIFO/GPIF Interrupt Sources Priority INT4VEC Value Source Notes 1 80 EP2PF Endpoint 2 Programmable Flag 2 84 EP4PF Endpoint 4 Programmable Flag 3 88 EP6PF Endpoint 6 Programmable Flag 4 8C EP8PF Endpoint 8 Programmable Flag 5 90 EP2EF Endpoint 2 Empty Flag 6 94 EP4EF Endpoint 4 Empty Flag 7 98 EP6EF Endpoint 6 Empty Flag 8 9C EP8EF Endpoint 8 Empty Flag 9 A0 EP2FF Endpoint 2 Full Flag 10 A4 EP4FF Endpoint 4 Full Flag 11 A8 EP6FF Endpoint 6 Full Flag 12 AC EP8FF Endpoint 8 Full Flag 13 B0 GPIFDONE 14 B4 GPIFWF GPIF Operation Complete GPIF Waveform If Autovectoring is enabled (AV4EN = 1 in the INTSETUP register), the FX1 substitutes its INT4VEC byte. Therefore, if the high byte (“page”) of a jump-table address is preloaded at location 0x0054, the automatically-inserted INT4VEC byte at 0x0055 will direct the jump to the correct address out of the 14 addresses within the page. When the ISR occurs, the FX1 pushes the program counter onto its stack then jumps to address 0x0053, where it expects to find a “jump” instruction to the ISR Interrupt service routine. 4.9 Reset and Wakeup 4.9.1 Reset Pin The input pin, RESET#, will reset the FX1 when asserted. This pin has hysteresis and is active LOW. When a crystal is used with the CY7C64713/4 the reset period must allow for the stabilization of the crystal and the PLL. This reset period should be approximately 5 ms after VCC has reached 3.0 Volts. If the crystal input pin is driven by a clock signal the internal PLL stabilizes in 200 µs after VCC has reached 3.0V[3]. Figure 4-2 shows a power on reset condition and a reset applied during operation. A power on reset is defined as the time reset is asserted while power is being applied to the circuit. A powered reset is defined to be when the FX1 has previously been powered on and operating and the RESET# pin is asserted. Cypress provides an application note which describes and recommends power on reset implementation and can be found on the Cypress web site. While the application note discusses the FX2, the information provided applies also to the FX1. For more information on reset implementation for the FX2 family of products visit the http://www.cypress.com. Note: 3. If the external clock is powered at the same time as the CY7C64713/4 and has a stabilization wait period, it must be added to the 200 µs. Document #: 38-08039 Rev. *B Page 5 of 50 CY7C64713/14 RESET# RESET# VIL VIL 3.3V 3.0V 3.3V VCC VCC 0V 0V TRESET TRESET Power on Reset Powered Reset Figure 4-2. Reset Timing Plots Table 4-5. Reset Timing Values Condition Power-On Reset with crystal Power-On Reset with external clock Powered Reset 4.9.2 TRESET 5 ms 200 µs + Clock stability time 200 µs Wakeup Pins The 8051 puts itself and the rest of the chip into a power-down mode by setting PCON.0 = 1. This stops the oscillator and PLL. When WAKEUP is asserted by external logic, the oscillator restarts, after the PLL stabilizes, and then the 8051 receives a wakeup interrupt. This applies whether or not FX1 is connected to the USB. The FX1 exits the power-down (USB suspend) state using one of the following methods: • USB bus activity (if D+/D– lines are left floating, noise on these lines may indicate activity to the FX1 and initiate a wakeup). • External logic asserts the WAKEUP pin • External logic asserts the PA3/WU2 pin. The second wakeup pin, WU2, can also be configured as a general purpose I/O pin. This allows a simple external R-C network to be used as a periodic wakeup source. Note that WAKEUP is by default active low. 4.10 Program/Data RAM 4.10.1 Size access it as both program and data memory. No USB control registers appear in this space. Two memory maps are shown in the following diagrams: Figure 4-3 Internal Code Memory, EA = 0 Figure 4-4 External Code Memory, EA = 1. 4.10.2 Internal Code Memory, EA = 0 This mode implements the internal 16-KByte block of RAM (starting at 0) as combined code and data memory. When external RAM or ROM is added, the external read and write strobes are suppressed for memory spaces that exist inside the chip. This allows the user to connect a 64-KByte memory without requiring address decodes to keep clear of internal memory spaces. Only the internal 16 KBytes and scratch pad 0.5 KBytes RAM spaces have the following access: • USB download • USB upload • Setup data pointer • I2C interface boot load. 4.10.3 External Code Memory, EA = 1 The bottom 16 KBytes of program memory is external, and therefore the bottom 16 KBytes of internal RAM is accessible only as data memory. The FX1 has 16 KBytes of internal program/data RAM, where PSEN#/RD# signals are internally ORed to allow the 8051 to Document #: 38-08039 Rev. *B Page 6 of 50 CY7C64713/14 Inside FX1 Outside FX1 FFFF 7.5 KBytes USB regs and 4K FIFO buffers (RD#,WR#) E200 E1FF 0.5 KBytes RAM E000 Data (RD#,WR#)* (OK to populate data memory here—RD#/WR# strobes are not active) 48 KBytes External Code Memory (PSEN#) 40 KBytes External Data Memory (RD#,WR#) 3FFF 16 KBytes RAM Code and Data (PSEN#,RD#,WR#)* (Ok to populate data memory here—RD#/WR# strobes are not active) (OK to populate program memory here— PSEN# strobe is not active) 0000 Data Code *SUDPTR, USB upload/download, I2C interface boot access Figure 4-3. Internal Code Memory, EA = 0 Inside FX1 Outside FX1 FFFF 7.5 KBytes USB regs and 4K FIFO buffers (RD#,WR#) E200 E1FF 0.5 KBytes RAM E000 Data (RD#,WR#)* (OK to populate data memory here—RD#/WR# strobes are not active) 40 KBytes External Data Memory (RD#,WR#) 64 KBytes External Code Memory (PSEN#) 3FFF 16 KBytes RAM Data (RD#,WR#)* (Ok to populate data memory here—RD#/WR# strobes are not active) 0000 Data Code *SUDPTR, USB upload/download, I2C interface boot access Figure 4-4. External Code Memory, EA = 1 Document #: 38-08039 Rev. *B Page 7 of 50 CY7C64713/14 4.11 Register Addresses FFFF 4 KBytes EP2-EP8 buffers (8 x 512) Not all Space is available for all transfer types F000 EFFF 2 KBytes RESERVED E800 E7FF E7C0 E7BF E780 E77F E740 E73F E700 E6FF E500 E4FF E480 E47F E400 E3FF E200 E1FF 64 Bytes EP1IN 64 Bytes EP1OUT 64 Bytes EP0 IN/OUT 64 Bytes RESERVED 8051 Addressable Registers (512) Reserved (128) 128 bytes GPIF Waveforms Reserved (512) 512 bytes 8051 xdata RAM E000 4.12 Endpoint RAM 4.12.1 Size • 3 × 64 bytes (Endpoints 0 and 1) • 8 × 512 bytes (Endpoints 2, 4, 6, 8) 4.12.2 Organization • EP0—Bidirectional endpoint zero, 64-byte buffer • EP1IN, EP1OUT—64-byte buffers, bulk or interrupt • EP2,4,6,8—Eight 512-byte buffers, bulk, interrupt, or isochronous, of which only the transfer size is available. EP4 and EP8 can be double buffered, while EP2 and 6 can Document #: 38-08039 Rev. *B be either double, triple, or quad buffered. Regardless of the physical size of the buffer, each endpoint buffer accommodates only one full-speed packet. For bulk endpoints the maximum number of bytes it can accommodate is 64, even though the physical buffer size is 512 or 1024. For an ISOCHRONOUS endpoint the maximum number of bytes it can accommodate is 1023. For endpoint configuration options, see Figure 4-5. 4.12.3 Setup Data Buffer A separate 8-byte buffer at 0xE6B8-0xE6BF holds the Setup data from a CONTROL transfer. Page 8 of 50 CY7C64713/14 4.12.4 Endpoint Configurations EP0 IN&OUT 64 64 64 64 64 64 64 64 64 64 64 64 EP1 IN 64 64 64 64 64 64 64 64 64 64 64 64 EP1 OUT 64 64 64 64 64 64 64 64 64 64 64 64 EP2 EP2 EP2 EP2 EP2 EP2 EP2 EP2 EP2 EP2 64 64 64 64 64 64 64 64 64 64 64 64 EP4 EP4 EP4 64 64 64 64 64 64 64 64 64 64 64 EP6 EP6 64 EP6 64 64 EP6 64 1023 64 EP8 1023 64 64 64 1 2 1023 64 1023 1023 1023 EP6 1023 3 EP6 EP6 64 64 64 64 64 1023 1023 1023 64 64 EP6 64 1023 64 EP8 EP8 64 64 64 64 4 5 EP6 1023 1023 64 EP8 64 1023 64 64 EP6 EP2 EP2 64 1023 6 64 64 64 64 7 8 1023 9 1023 1023 EP8 64 64 64 64 10 1023 11 1023 12 Figure 4-5. Endpoint Configuration Endpoints 0 and 1 are the same for every configuration. Endpoint 0 is the only CONTROL endpoint, and endpoint 1 can be either BULK or INTERRUPT. The endpoint buffers can be configured in any 1 of the 12 configurations shown in the vertical columns. In full-speed, BULK mode uses only the first 64 bytes of each buffer, even though memory exists for the allocation of the isochronous transfers in BULK mode the unused endpoint buffer space is not available for other operations. An example endpoint configuration would be: EP2—1023 double buffered; EP6—64 quad buffered (column 8). 4.12.5 Default Alternate Settings Table 4-6. Default Alternate Settings[4, 5] Alternate Setting 0 ep0 1 64 64 2 64 3 64 ep1out 0 64 bulk 64 int 64 int ep1in 0 64 bulk 64 int 64 int ep2 0 64 bulk out (2×) 64 int out (2×) 64 iso out (2×) ep4 0 64 bulk out (2×) 64 bulk out (2×) 64 bulk out (2×) ep6 0 64 bulk in (2×) 64 int in (2×) ep8 0 64 bulk in (2×) 64 bulk in (2×) 64 bulk in (2×) 4.13 External FIFO Interface 4.13.1 Architecture are controlled by FIFO control signals (such as IFCLK, SLCS#, SLRD, SLWR, SLOE, PKTEND, and flags). The usable size of these buffers depend on the USB transfer mode as described in Section 4.12.2. In operation, some of the eight RAM blocks fill or empty from the SIE, while the others are connected to the I/O transfer logic. The transfer logic takes two forms, the GPIF for internally generated control signals, or the slave FIFO interface for externally controlled transfers. 4.13.2 Master/Slave Control Signals The FX1 endpoint FIFOS are implemented as eight physically distinct 256x16 RAM blocks. The 8051/SIE can switch any of the RAM blocks between two domains, the USB (SIE) domain and the 8051-I/O Unit domain. This switching is done virtually instantaneously, giving essentially zero transfer time between “USB FIFOS” and “Slave FIFOS.” Since they are physically the same memory, no bytes are actually transferred between buffers. 64 iso in (2×) The FX1 slave FIFO architecture has eight 512-byte blocks in the endpoint RAM that directly serve as FIFO memories, and Notes: 4. “0” means “not implemented.” 5. “2×” means “double buffered.” Document #: 38-08039 Rev. *B Page 9 of 50 CY7C64713/14 At any given time, some RAM blocks are filling/emptying with USB data under SIE control, while other RAM blocks are available to the 8051 and/or the I/O control unit. The RAM blocks operate as single-port in the USB domain, and dualport in the 8051-I/O domain. The blocks can be configured as single, double, triple, or quad buffered as previously shown. The I/O control unit implements either an internal-master (M for master) or external-master (S for Slave) interface. In Master (M) mode, the GPIF internally controls FIFOADR[1..0] to select a FIFO. The RDY pins (two in the 56pin package, six in the 100-pin and 128-pin packages) can be used as flag inputs from an external FIFO or other logic if desired. The GPIF can be run from either an internally derived clock or externally supplied clock (IFCLK), at a rate that transfers data up to 96 Megabytes/s (48-MHz IFCLK with 16bit interface). In Slave (S) mode, the FX1 accepts either an internally derived clock or externally supplied clock (IFCLK, max. frequency 48 MHz) and SLCS#, SLRD, SLWR, SLOE, PKTEND signals from external logic. When using an external IFCLK, the external clock must be present before switching to the external clock with the IFCLKSRC bit. Each endpoint can individually be selected for byte or word operation by an internal configuration bit, and a Slave FIFO Output Enable signal SLOE enables data of the selected width. External logic must insure that the output enable signal is inactive when writing data to a slave FIFO. The slave interface can also operate asynchronously, where the SLRD and SLWR signals act directly as strobes, rather than a clock qualifier as in synchronous mode. The signals SLRD, SLWR, SLOE and PKTEND are gated by the signal SLCS#. 4.13.3 GPIF and FIFO Clock Rates An 8051 register bit selects one of two frequencies for the internally supplied interface clock: 30 MHz and 48 MHz. Alternatively, an externally supplied clock of 5 MHz–48 MHz feeding the IFCLK pin can be used as the interface clock. IFCLK can be configured to function as an output clock when the GPIF and FIFOs are internally clocked. An output enable bit in the IFCONFIG register turns this clock output off, if desired. Another bit within the IFCONFIG register will invert the IFCLK signal whether internally or externally sourced. 4.14 GPIF The GPIF is a flexible 8- or 16-bit parallel interface driven by a user-programmable finite state machine. It allows the CY7C64713/4 to perform local bus mastering, and can implement a wide variety of protocols such as ATA interface, printer parallel port, and Utopia. The GPIF has six programmable control outputs (CTL), nine address outputs (GPIFADRx), and six general-purpose ready inputs (RDY). The data bus width can be 8 or 16 bits. Each GPIF vector defines the state of the control outputs, and determines what state a ready input (or multiple inputs) must be before proceeding. The GPIF vector can be programmed to advance a FIFO to the next data value, advance an address, etc. A sequence of the GPIF vectors make up a single waveform that will be executed to perform the desired data move between the FX1 and the external device. 4.14.1 Six Control OUT Signals The 100- and 128-pin packages bring out all six Control Output pins (CTL0-CTL5). The 8051 programs the GPIF unit to define the CTL waveforms. The 56-pin package brings out three of these signals, CTL0–CTL2. CTLx waveform edges can be programmed to make transitions as fast as once per clock (20.8 ns using a 48-MHz clock). 4.14.2 Six Ready IN Signals The 100- and 128-pin packages bring out all six Ready inputs (RDY0–RDY5). The 8051 programs the GPIF unit to test the RDY pins for GPIF branching. The 56-pin package brings out two of these signals, RDY0–1. 4.14.3 Nine GPIF Address OUT Signals Nine GPIF address lines are available in the 100- and 128-pin packages, GPIFADR[8..0]. The GPIF address lines allow indexing through up to a 512-byte block of RAM. If more address lines are needed, I/O port pins can be used. 4.14.4 Long Transfer Mode In master mode, the 8051 appropriately sets GPIF transaction count registers (GPIFTCB3, GPIFTCB2, GPIFTCB1, or GPIFTCB0) for unattended transfers of up to 232 transactions. The GPIF automatically throttles data flow to prevent under or overflow until the full number of requested transactions complete. The GPIF decrements the value in these registers to represent the current status of the transaction. 4.15 ECC Generation The EZ-USB FX1 can calculate ECCs (Error-Correcting Codes) on data that passes across its GPIF or Slave FIFO interfaces. There are two ECC configurations: Two ECCs, each calculated over 256 bytes (SmartMedia™ Standard); and one ECC calculated over 512 bytes. The ECC can correct any one-bit error or detect any two-bit error. Note: To use the ECC logic, the GPIF or Slave FIFO interface must be configured for byte-wide operation. 4.15.1 ECC Implementation The two ECC configurations are selected by the ECCM bit: 4.15.1.1 ECCM = 0 Two 3-byte ECCs, each calculated over a 256-byte block of data. This configuration conforms to the SmartMedia Standard. Write any value to ECCRESET, then pass data across the GPIF or Slave FIFO interface. The ECC for the first 256 bytes of data will be calculated and stored in ECC1. The ECC for the next 256 bytes will be stored in ECC2. After the second ECC is calculated, the values in the ECCx registers will not change until ECCRESET is written again, even if more data is subsequently passed across the interface. 4.15.1.2 ECCM=1 One 3-byte ECC calculated over a 512-byte block of data. Write any value to ECCRESET then pass data across the GPIF or Slave FIFO interface. The ECC for the first 512 bytes of data will be calculated and stored in ECC1; ECC2 is unused. After the ECC is calculated, the value in ECC1 will not change Document #: 38-08039 Rev. *B Page 10 of 50 CY7C64713/14 until ECCRESET is written again, even if more data is subsequently passed across the interface 4.16 USB Uploads and Downloads The core has the ability to directly edit the data contents of the internal 16 KByte RAM and of the internal 512-byte scratch pad RAM via a vendor-specific command. This capability is normally used when “soft” downloading user code and is available only to and from internal RAM, only when the 8051 is held in reset. The available RAM spaces are 16 KBytes from 0x0000–0x3FFF (code/data) and 512 bytes from 0xE000–0xE1FF (scratch pad data RAM).[6] 4.17 Autopointer Access FX1 provides two identical autopointers. They are similar to the internal 8051 data pointers, but with an additional feature: they can optionally increment after every memory access. This capability is available to and from both internal and external RAM. The autopointers are available in external FX1 registers, under control of a mode bit (AUTOPTRSETUP.0). Using the external FX1 autopointer access (at 0xE67B – 0xE67C) allows the autopointer to access all RAM, internal and external to the part. Also, the autopointers can point to any FX1 register or endpoint buffer space. When autopointer access to external memory is enabled, location 0xE67B and 0xE67C in XDATA and code space cannot be used. 4.18 I2C Controller FX1 has one I2C port that is driven by two internal controllers, one that automatically operates at boot time to load VID/PID/DID and configuration information, and another that the 8051, once running, uses to control external I2C devices. The I2C port operates in master mode only. 4.18.1 I2C Port Pins I2C- pins SCL and SDA must have external 2.2-kΩ pullThe up resistors even if no EEPROM is connected to the FX1. External EEPROM device address pins must be configured properly. See Table 4-7 for configuring the device address pins. Table 4-7. Strap Boot EEPROM Address Lines to These Values Bytes Example EEPROM [7] A2 A1 A0 16 24LC00 N/A N/A N/A 128 24LC01 0 0 0 256 24LC02 0 0 0 4K 24LC32 0 0 1 8K 24LC64 0 0 1 16K 24LC128 0 0 1 4.18.2 I2C Interface Boot Load Access At power-on reset the I2C interface boot loader will load the VID/PID/DID configuration bytes and up to 16 KBytes of program/data. The available RAM spaces are 16 KBytes from 0x0000–0x3FFF and 512 bytes from 0xE000–0xE1FF. The 8051 will be in reset. I2C interface boot loads only occur after power-on reset. 4.18.3 I2C Interface General Purpose Access The 8051 can control peripherals connected to the I2C bus using the I2CTL and I2DAT registers. FX1 provides I2C master control only, it is never an I2C slave. 4.19 Compatible with Previous Generation EZ-USB FX2 The EZ-USB FX1 is fit/form/function-upgradable to the EZUSB FX2LP. This makes for a easy transition for designers wanting to upgrade their systems from full-speed to the highspeed designs. The pinout and package selection are identical, and all of the firmware developed for the FX1 will function in the FX2LP with proper addition of High Speed descriptors and speed switching code. 5.0 Pin Assignments Figure 5-1 identifies all signals for the three package types. The following pages illustrate the individual pin diagrams, plus a combination diagram showing which of the full set of signals are available in the 128-, 100-, and 56-pin packages. The signals on the left edge of the 56-pin package in Figure 51 are common to all versions in the FX1 family. Three modes are available in all package versions: Port, GPIF master, and Slave FIFO. These modes define the signals on the right edge of the diagram. The 8051 selects the interface mode using the IFCONFIG[1:0] register bits. Port mode is the power-on default configuration. The 100-pin package adds functionality to the 56-pin package by adding these pins: • PORTC or alternate GPIFADR[7:0] address signals • PORTE or alternate GPIFADR[8] address signal and seven additional 8051 signals • Three GPIF Control signals • Four GPIF Ready signals • Nine 8051 signals (two USARTs, three timer inputs, INT4,and INT5#) • BKPT, RD#, WR#. The 128-pin package adds the 8051 address and data buses plus control signals. Note that two of the required signals, RD# and WR#, are present in the 100-pin version. In the 100-pin and 128-pin versions, an 8051 control bit can be set to pulse the RD# and WR# pins when the 8051 reads from/writes to PORTC. Notes: 6. After the data has been downloaded from the host, a “loader” can execute from internal RAM in order to transfer downloaded data to external memory. 7. This EEPROM does not have address pins. Document #: 38-08039 Rev. *B Page 11 of 50 CY7C64713/14 Port GPIF Master PD7 PD6 PD5 PD4 PD3 PD2 PD1 PD0 PB7 PB6 PB5 PB4 PB3 PB2 PB1 PB0 XTALIN XTALOUT RESET# WAKEUP# SCL SDA 56 T0OUT T1OUT INT0#/PA0 INT1#/PA1 PA2 WU2/PA3 PA4 PA5 PA6 PA7 IFCLK CLKOUT DPLUS DMINUS FD[15] FD[14] FD[13] FD[12] FD[11] FD[10] FD[9] FD[8] FD[7] FD[6] FD[5] FD[4] FD[3] FD[2] FD[1] FD[0] Slave FIFO FD[15] FD[14] FD[13] FD[12] FD[11] FD[10] FD[9] FD[8] FD[7] FD[6] FD[5] FD[4] FD[3] FD[2] FD[1] FD[0] RDY0 RDY1 SLRD SLWR CTL0 CTL1 CTL2 FLAGA FLAGB FLAGC INT0#/PA0 INT1#/PA1 PA2 WU2/PA3 PA4 PA5 PA6 PA7 INT0#/ PA0 INT1#/ PA1 SLOE WU2/PA3 FIFOADR0 FIFOADR1 PKTEND PA7/FLAGD/SLCS# CTL3 CTL4 CTL5 RDY2 RDY3 RDY4 RDY5 100 BKPT PORTC7/GPIFADR7 PORTC6/GPIFADR6 PORTC5/GPIFADR5 PORTC4/GPIFADR4 PORTC3/GPIFADR3 PORTC2/GPIFADR2 PORTC1/GPIFADR1 PORTC0/GPIFADR0 PE7/GPIFADR8 PE6/T2EX PE5/INT6 PE4/RxD1OUT PE3/RxD0OUT PE2/T2OUT PE1/T1OUT PE0/T0OUT RD# WR# CS# OE# PSEN# D7 D6 D5 D4 D3 D2 D1 D0 128 EA RxD0 TxD0 RxD1 TxD1 INT4 INT5# T2 T1 T0 A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 Figure 5-1. Signals Document #: 38-08039 Rev. *B Page 12 of 50 CY7C64713/14 27 28 29 30 31 32 33 34 35 36 37 38 103 26 104 25 105 24 106 23 107 22 108 21 109 20 110 19 111 18 112 17 113 16 114 15 115 14 116 13 117 12 118 11 119 10 120 9 121 8 122 7 123 6 124 5 125 4 126 3 PD1/FD9 PD2/FD10 PD3/FD11 INT5# VCC PE0/T0OUT PE1/T1OUT PE2/T2OUT PE3/RXD0OUT PE4/RXD1OUT PE5/INT6 PE6/T2EX PE7/GPIFADR8 GND A4 A5 A6 A7 PD4/FD12 PD5/FD13 PD6/FD14 PD7/FD15 GND A8 A9 A10 2 127 128 1 CLKOUT VCC GND RDY0/*SLRD RDY1/*SLWR RDY2 RDY3 RDY4 RDY5 AVCC XTALOUT XTALIN AGND NC NC NC AVCC DPLUS DMINUS AGND A11 A12 A13 A14 A15 VCC GND INT4 T0 T1 T2 *IFCLK RESERVED BKPT EA SCL SDA OE# PD0/FD8 *WAKEUP VCC RESET# CTL5 A3 A2 A1 A0 GND PA7/*FLAGD/SLCS# PA6/*PKTEND PA5/FIFOADR1 PA4/FIFOADR0 D7 D6 D5 PA3/*WU2 PA2/*SLOE PA1/INT1# PA0/INT0# VCC GND PC7/GPIFADR7 PC6/GPIFADR6 PC5/GPIFADR5 PC4/GPIFADR4 PC3/GPIFADR3 PC2/GPIFADR2 PC1/GPIFADR1 PC0/GPIFADR0 CTL2/*FLAGC CTL1/*FLAGB CTL0/*FLAGA VCC CTL4 CTL3 GND CY7C64713/4 128-pin TQFP 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 VCC D4 D3 D2 D1 D0 GND PB7/FD7 PB6/FD6 PB5/FD5 PB4/FD4 RXD1 TXD1 RXD0 TXD0 GND VCC PB3/FD3 PB2/FD2 PB1/FD1 PB0/FD0 VCC CS# WR# RD# PSEN# 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 Figure 5-2. CY7C64713/4 128-pin TQFP Pin Assignment * denotes programmable polarity Document #: 38-08039 Rev. *B Page 13 of 50 CY7C64713/14 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 PD1/FD9 PD2/FD10 PD3/FD11 INT5# VCC PE0/T0OUT PE1/T1OUT PE2/T2OUT PE3/RXD0OUT PE4/RXD1OUT PE5/INT6 PE6/T2EX PE7/GPIFADR8 GND PD4/FD12 PD5/FD13 PD6/FD14 PD7/FD15 GND CLKOUT 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 VCC GND RDY0/*SLRD RDY1/*SLWR RDY2 RDY3 RDY4 RDY5 AVCC XTALOUT XTALIN AGND NC NC NC AVCC DPLUS DMINUS AGND VCC GND INT4 T0 T1 T2 *IFCLK RESERVED BKPT SCL SDA PD0/FD8 *WAKEUP VCC RESET# CTL5 GND PA7/*FLAGD/SLCS# PA6/*PKTEND PA5/FIFOADR1 PA4/FIFOADR0 PA3/*WU2 PA2/*SLOE PA1/INT1# PA0/INT0# VCC GND PC7/GPIFADR7 PC6/GPIFADR6 PC5/GPIFADR5 PC4/GPIFADR4 PC3/GPIFADR3 PC2/GPIFADR2 PC1/GPIFADR1 PC0/GPIFADR0 CTL2/*FLAGC CTL1/*FLAGB CTL0/*FLAGA VCC CTL4 CTL3 CY7C64713/4 100-pin TQFP 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 GND VCC GND PB7/FD7 PB6/FD6 PB5/FD5 PB4/FD4 RXD1 TXD1 RXD0 TXD0 GND VCC PB3/FD3 PB2/FD2 PB1/FD1 PB0/FD0 VCC WR# RD# 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 Figure 5-3. CY7C64713/4 100-pin TQFP Pin Assignment * denotes programmable polarity Document #: 38-08039 Rev. *B Page 14 of 50 CY7C64713/14 GND VCC CLKOUT/**PE1/T1OUT GND PD7/FD15 PD6/FD14 PD5/FD13 PD4/FD12 PD3/FD11 PD2/FD10 PD1/FD9 PD0/FD8 *WAKEUP VCC 56 55 54 53 52 51 50 49 48 47 46 45 44 43 RDY0/*SLRD 1 42 RESET# RDY1/*SLWR 2 41 GND AVCC 3 40 PA7/*FLAGD/SLCS# XTALOUT 4 39 PA6/*PKTEND XTALIN 5 38 PA5/FIFOADR1 AGND 6 37 PA4/FIFOADR0 AVCC 7 36 PA3/*WU2 DPLUS 8 35 PA2/*SLOE DMINUS 9 34 PA1/INT1# AGND 10 33 PA0/INT0# VCC 11 32 VCC GND 12 31 CTL2/*FLAGC *IFCLK/**PE0/T0OUT 13 30 CTL1/*FLAGB RESERVED 14 29 CTL0/*FLAGA CY7C64713/4 56-pin QFN 19 20 21 22 23 24 25 26 27 28 PB0/FD0 PB1/FD1 PB2/FD2 PB3/FD3 PB4/FD4 PB5/FD5 PB6/FD6 PB7/FD7 GND VCC GND VCC 18 17 SDA SCL 16 15 Figure 5-4. CY7C64713/4 56-pin QFN Pin Assignment * denotes programmable polarity Document #: 38-08039 Rev. *B Page 15 of 50 CY7C64713/14 5.1 CY7C64713/4 Pin Definitions Table 5-1. FX1 Pin Definitions [8] 128 100 56 TQFP TQFP QFN Name Type Default Description 10 9 3 AVCC Power N/A Analog VCC. Connect this pin to 3.3V power source. This signal provides power to the analog section of the chip. 17 16 7 AVCC Power N/A Analog VCC. Connect this pin to 3.3V power source. This signal provides power to the analog section of the chip. 13 12 6 AGND Ground N/A Analog Ground. Connect to ground with as short a path as possible. 20 19 10 AGND Ground N/A Analog Ground. Connect to ground with as short a path as possible. 19 18 9 DMINUS I/O/Z Z USB D– Signal. Connect to the USB D– signal. 18 17 8 DPLUS I/O/Z Z USB D+ Signal. Connect to the USB D+ signal. 94 A0 Output L 95 A1 Output L 8051 Address Bus. This bus is driven at all times. When the 8051 is addressing internal RAM it reflects the internal address. 96 A2 Output L 97 A3 Output L 117 A4 Output L 118 A5 Output L 119 A6 Output L 120 A7 Output L 126 A8 Output L 127 A9 Output L 128 A10 Output L 21 A11 Output L 22 A12 Output L 23 A13 Output L 24 A14 Output L 25 A15 Output L 59 D0 I/O/Z Z 60 D1 I/O/Z Z 61 D2 I/O/Z Z 62 D3 I/O/Z Z 63 D4 I/O/Z Z 86 D5 I/O/Z Z 87 D6 I/O/Z Z 88 D7 I/O/Z Z 39 PSEN# Output H Program Store Enable. This active-LOW signal indicates an 8051 code fetch from external memory. It is active for program memory fetches from 0x4000–0xFFFF when the EA pin is LOW, or from 0x0000–0xFFFF when the EA pin is HIGH. BKPT Output L Breakpoint. This pin goes active (HIGH) when the 8051 address bus matches the BPADDRH/L registers and breakpoints are enabled in the BREAKPT register (BPEN = 1). If the BPPULSE bit in the BREAKPT register is HIGH, this signal pulses HIGH for eight 12-/24-/48-MHz clocks. If the BPPULSE bit is LOW, the signal remains HIGH until the 8051 clears the BREAK bit (by writing 1 to it) in the BREAKPT register. 34 28 8051 Data Bus. This bidirectional bus is high-impedance when inactive, input for bus reads, and output for bus writes. The data bus is used for external 8051 program and data memory. The data bus is active only for external bus accesses, and is driven LOW in suspend. Note: 8. Unused inputs should not be left floating. Tie either HIGH or LOW as appropriate. Outputs should only be pulled up or down to ensure signals at power-up and in standby. Note also that no pins should be driven while the device is powered down. Document #: 38-08039 Rev. *B Page 16 of 50 CY7C64713/14 Table 5-1. FX1 Pin Definitions (continued)[8] 128 100 56 TQFP TQFP QFN 99 77 42 35 Name Type Default RESET# Input N/A Active LOW Reset. Resets the entire chip. See section 4.9 ”Reset and Wakeup” on page 5 for more details. Description EA Input N/A External Access. This pin determines where the 8051 fetches code between addresses 0x0000 and 0x3FFF. If EA = 0 the 8051 fetches this code from its internal RAM. IF EA = 1 the 8051 fetches this code from external memory. Input N/A Crystal Input. Connect this signal to a 24-MHz parallel-resonant, fundamental mode crystal and load capacitor to GND. It is also correct to drive XTALIN with an external 24 MHz square wave derived from another clock source. When driving from an external source, the driving signal should be a 3.3V square wave. Crystal Output. Connect this signal to a 24-MHz parallel-resonant, fundamental mode crystal and load capacitor to GND. If an external clock is used to drive XTALIN, leave this pin open. 12 11 5 XTALIN 11 10 4 XTALOUT Output N/A 1 100 54 CLKOUT O/Z 12 CLKOUT: 12-, 24- or 48-MHz clock, phase locked to the 24-MHz input MHz clock. The 8051 defaults to 12-MHz operation. The 8051 may three-state this output by setting CPUCS.1 = 1. 82 67 33 PA0 or INT0# I/O/Z I Multiplexed pin whose function is selected by PORTACFG.0 (PA0) PA0 is a bidirectional IO port pin. INT0# is the active-LOW 8051 INT0 interrupt input signal, which is either edge triggered (IT0 = 1) or level triggered (IT0 = 0). 83 68 34 PA1 or INT1# I/O/Z I Multiplexed pin whose function is selected by: (PA1) PORTACFG.1 PA1 is a bidirectional IO port pin. INT1# is the active-LOW 8051 INT1 interrupt input signal, which is either edge triggered (IT1 = 1) or level triggered (IT1 = 0). 84 69 35 PA2 or SLOE I/O/Z I Multiplexed pin whose function is selected by two bits: (PA2) IFCONFIG[1:0]. PA2 is a bidirectional IO port pin. SLOE is an input-only output enable with programmable polarity (FIFOPINPOLAR.4) for the slave FIFOs connected to FD[7..0] or FD[15..0]. 85 70 36 PA3 or WU2 I/O/Z I Multiplexed pin whose function is selected by: (PA3) WAKEUP.7 and OEA.3 PA3 is a bidirectional I/O port pin. WU2 is an alternate source for USB Wakeup, enabled by WU2EN bit (WAKEUP.1) and polarity set by WU2POL (WAKEUP.4). If the 8051 is in suspend and WU2EN = 1, a transition on this pin starts up the oscillator and interrupts the 8051 to allow it to exit the suspend mode. Asserting this pin inhibits the chip from suspending, if WU2EN=1. 89 71 37 PA4 or I/O/Z FIFOADR0 I Multiplexed pin whose function is selected by: (PA4) IFCONFIG[1..0]. PA4 is a bidirectional I/O port pin. FIFOADR0 is an input-only address select for the slave FIFOs connected to FD[7..0] or FD[15..0]. 90 72 38 PA5 or I/O/Z FIFOADR1 I Multiplexed pin whose function is selected by: (PA5) IFCONFIG[1..0]. PA5 is a bidirectional I/O port pin. FIFOADR1 is an input-only address select for the slave FIFOs connected to FD[7..0] or FD[15..0]. 91 73 39 PA6 or PKTEND I Multiplexed pin whose function is selected by the IFCONFIG[1:0] bits. (PA6) PA6 is a bidirectional I/O port pin. PKTEND is an input used to commit the FIFO packet data to the endpoint and whose polarity is programmable via FIFOPINPOLAR.5. Port A Document #: 38-08039 Rev. *B I/O/Z Page 17 of 50 CY7C64713/14 Table 5-1. FX1 Pin Definitions (continued)[8] 128 100 56 TQFP TQFP QFN 92 Name Type Default Description 74 40 PA7 or I/O/Z FLAGD or SLCS# I Multiplexed pin whose function is selected by the IFCONFIG[1:0] and (PA7) PORTACFG.7 bits. PA7 is a bidirectional I/O port pin. FLAGD is a programmable slave-FIFO output status flag signal. SLCS# gates all other slave FIFO enable/strobes 44 34 18 PB0 or FD[0] I/O/Z I Multiplexed pin whose function is selected by the following bits: (PB0) IFCONFIG[1..0]. PB0 is a bidirectional I/O port pin. FD[0] is the bidirectional FIFO/GPIF data bus. 45 35 19 PB1 or FD[1] I/O/Z I Multiplexed pin whose function is selected by the following bits: (PB1) IFCONFIG[1..0]. PB1 is a bidirectional I/O port pin. FD[1] is the bidirectional FIFO/GPIF data bus. 46 36 20 PB2 or FD[2] I/O/Z I Multiplexed pin whose function is selected by the following bits: (PB2) IFCONFIG[1..0]. PB2 is a bidirectional I/O port pin. FD[2] is the bidirectional FIFO/GPIF data bus. 47 37 21 PB3 or FD[3] I/O/Z I Multiplexed pin whose function is selected by the following bits: (PB3) IFCONFIG[1..0]. PB3 is a bidirectional I/O port pin. FD[3] is the bidirectional FIFO/GPIF data bus. 54 44 22 PB4 or FD[4] I/O/Z I Multiplexed pin whose function is selected by the following bits: (PB4) IFCONFIG[1..0]. PB4 is a bidirectional I/O port pin. FD[4] is the bidirectional FIFO/GPIF data bus. 55 45 23 PB5 or FD[5] I/O/Z I Multiplexed pin whose function is selected by the following bits: (PB5) IFCONFIG[1..0]. PB5 is a bidirectional I/O port pin. FD[5] is the bidirectional FIFO/GPIF data bus. 56 46 24 PB6 or FD[6] I/O/Z I Multiplexed pin whose function is selected by the following bits: (PB6) IFCONFIG[1..0]. PB6 is a bidirectional I/O port pin. FD[6] is the bidirectional FIFO/GPIF data bus. 57 47 25 PB7 or FD[7] I/O/Z I Multiplexed pin whose function is selected by the following bits: (PB7) IFCONFIG[1..0]. PB7 is a bidirectional I/O port pin. FD[7] is the bidirectional FIFO/GPIF data bus. Port B PORT C 72 57 PC0 or I/O/Z GPIFADR0 I Multiplexed pin whose function is selected by PORTCCFG.0 (PC0) PC0 is a bidirectional I/O port pin. GPIFADR0 is a GPIF address output pin. 73 58 PC1 or I/O/Z GPIFADR1 I Multiplexed pin whose function is selected by PORTCCFG.1 (PC1) PC1 is a bidirectional I/O port pin. GPIFADR1 is a GPIF address output pin. 74 59 PC2 or I/O/Z GPIFADR2 I Multiplexed pin whose function is selected by PORTCCFG.2 (PC2) PC2 is a bidirectional I/O port pin. GPIFADR2 is a GPIF address output pin. 75 60 PC3 or I/O/Z GPIFADR3 I Multiplexed pin whose function is selected by PORTCCFG.3 (PC3) PC3 is a bidirectional I/O port pin. GPIFADR3 is a GPIF address output pin. 76 61 PC4 or I/O/Z GPIFADR4 I Multiplexed pin whose function is selected by PORTCCFG.4 (PC4) PC4 is a bidirectional I/O port pin. GPIFADR4 is a GPIF address output pin. Document #: 38-08039 Rev. *B Page 18 of 50 CY7C64713/14 Table 5-1. FX1 Pin Definitions (continued)[8] 128 100 56 TQFP TQFP QFN Name Type Default Description 77 62 PC5 or I/O/Z GPIFADR5 I Multiplexed pin whose function is selected by PORTCCFG.5 (PC5) PC5 is a bidirectional I/O port pin. GPIFADR5 is a GPIF address output pin. 78 63 PC6 or I/O/Z GPIFADR6 I Multiplexed pin whose function is selected by PORTCCFG.6 (PC6) PC6 is a bidirectional I/O port pin. GPIFADR6 is a GPIF address output pin. 79 64 PC7 or I/O/Z GPIFADR7 I Multiplexed pin whose function is selected by PORTCCFG.7 (PC7) PC7 is a bidirectional I/O port pin. GPIFADR7 is a GPIF address output pin. PORT D 102 80 45 PD0 or FD[8] I/O/Z I Multiplexed pin whose function is selected by the IFCONFIG[1..0] and (PD0) EPxFIFOCFG.0 (wordwide) bits. FD[8] is the bidirectional FIFO/GPIF data bus. 103 81 46 PD1 or FD[9] I/O/Z I Multiplexed pin whose function is selected by the IFCONFIG[1..0] and (PD1) EPxFIFOCFG.0 (wordwide) bits. FD[9] is the bidirectional FIFO/GPIF data bus. 104 82 47 PD2 or FD[10] I/O/Z I Multiplexed pin whose function is selected by the IFCONFIG[1..0] and (PD2) EPxFIFOCFG.0 (wordwide) bits. FD[10] is the bidirectional FIFO/GPIF data bus. 105 83 48 PD3 or FD[11] I/O/Z I Multiplexed pin whose function is selected by the IFCONFIG[1..0] and (PD3) EPxFIFOCFG.0 (wordwide) bits. FD[11] is the bidirectional FIFO/GPIF data bus. 121 95 49 PD4 or FD[12] I/O/Z I Multiplexed pin whose function is selected by the IFCONFIG[1..0] and (PD4) EPxFIFOCFG.0 (wordwide) bits. FD[12] is the bidirectional FIFO/GPIF data bus. 122 96 50 PD5 or FD[13] I/O/Z I Multiplexed pin whose function is selected by the IFCONFIG[1..0] and (PD5) EPxFIFOCFG.0 (wordwide) bits. FD[13] is the bidirectional FIFO/GPIF data bus. 123 97 51 PD6 or FD[14] I/O/Z I Multiplexed pin whose function is selected by the IFCONFIG[1..0] and (PD6) EPxFIFOCFG.0 (wordwide) bits. FD[14] is the bidirectional FIFO/GPIF data bus. 124 98 52 PD7 or FD[15] I/O/Z I Multiplexed pin whose function is selected by the IFCONFIG[1..0] and (PD7) EPxFIFOCFG.0 (wordwide) bits. FD[15] is the bidirectional FIFO/GPIF data bus. Port E 108 86 PE0 or T0OUT I/O/Z I Multiplexed pin whose function is selected by the PORTECFG.0 bit. (PE0) PE0 is a bidirectional I/O port pin. T0OUT is an active-HIGH signal from 8051 Timer-counter0. T0OUT outputs a high level for one CLKOUT clock cycle when Timer0 overflows. If Timer0 is operated in Mode 3 (two separate timer/counters), T0OUT is active when the low byte timer/counter overflows. 109 87 PE1 or T1OUT I/O/Z I Multiplexed pin whose function is selected by the PORTECFG.1 bit. (PE1) PE1 is a bidirectional I/O port pin. T1OUT is an active-HIGH signal from 8051 Timer-counter1. T1OUT outputs a high level for one CLKOUT clock cycle when Timer1 overflows. If Timer1 is operated in Mode 3 (two separate timer/counters), T1OUT is active when the low byte timer/counter overflows. 110 88 PE2 or T2OUT I/O/Z I Multiplexed pin whose function is selected by the PORTECFG.2 bit. (PE2) PE2 is a bidirectional I/O port pin. T2OUT is the active-HIGH output signal from 8051 Timer2. T2OUT is active (HIGH) for one clock cycle when Timer/Counter 2 overflows. Document #: 38-08039 Rev. *B Page 19 of 50 CY7C64713/14 Table 5-1. FX1 Pin Definitions (continued)[8] 128 100 56 TQFP TQFP QFN Name Type Description Default 111 89 PE3 or I/O/Z RXD0OUT I Multiplexed pin whose function is selected by the PORTECFG.3 bit. (PE3) PE3 is a bidirectional I/O port pin. RXD0OUT is an active-HIGH signal from 8051 UART0. If RXD0OUT is selected and UART0 is in Mode 0, this pin provides the output data for UART0 only when it is in sync mode. Otherwise it is a 1. 112 90 PE4 or I/O/Z RXD1OUT I Multiplexed pin whose function is selected by the PORTECFG.4 bit. (PE4) PE4 is a bidirectional I/O port pin. RXD1OUT is an active-HIGH output from 8051 UART1. When RXD1OUT is selected and UART1 is in Mode 0, this pin provides the output data for UART1 only when it is in sync mode. In Modes 1, 2, and 3, this pin is HIGH. 113 91 PE5 or INT6 I/O/Z I Multiplexed pin whose function is selected by the PORTECFG.5 bit. (PE5) PE5 is a bidirectional I/O port pin. INT6 is the 8051 INT6 interrupt request input signal. The INT6 pin is edgesensitive, active HIGH. 114 92 PE6 or T2EX I/O/Z I Multiplexed pin whose function is selected by the PORTECFG.6 bit. (PE6) PE6 is a bidirectional I/O port pin. T2EX is an active-high input signal to the 8051 Timer2. T2EX reloads timer 2 on its falling edge. T2EX is active only if the EXEN2 bit is set in T2CON. 115 93 PE7 or I/O/Z GPIFADR8 4 3 1 RDY0 or SLRD Input N/A Multiplexed pin whose function is selected by the following bits: IFCONFIG[1..0]. RDY0 is a GPIF input signal. SLRD is the input-only read strobe with programmable polarity (FIFOPINPOLAR.3) for the slave FIFOs connected to FD[7..0] or FD[15..0]. 5 4 2 RDY1 or SLWR Input N/A Multiplexed pin whose function is selected by the following bits: IFCONFIG[1..0]. RDY1 is a GPIF input signal. SLWR is the input-only write strobe with programmable polarity (FIFOPINPOLAR.2) for the slave FIFOs connected to FD[7..0] or FD[15..0]. 6 5 RDY2 Input N/A RDY2 is a GPIF input signal. 7 6 RDY3 Input N/A RDY3 is a GPIF input signal. 8 7 RDY4 Input N/A RDY4 is a GPIF input signal. 9 8 RDY5 Input N/A RDY5 is a GPIF input signal. 69 54 29 CTL0 or FLAGA O/Z H Multiplexed pin whose function is selected by the following bits: IFCONFIG[1..0]. CTL0 is a GPIF control output. FLAGA is a programmable slave-FIFO output status flag signal. Defaults to programmable for the FIFO selected by the FIFOADR[1:0] pins. 70 55 30 CTL1 or FLAGB O/Z H Multiplexed pin whose function is selected by the following bits: IFCONFIG[1..0]. CTL1 is a GPIF control output. FLAGB is a programmable slave-FIFO output status flag signal. Defaults to FULL for the FIFO selected by the FIFOADR[1:0] pins. 71 56 31 CTL2 or FLAGC O/Z H Multiplexed pin whose function is selected by the following bits: IFCONFIG[1..0]. CTL2 is a GPIF control output. FLAGC is a programmable slave-FIFO output status flag signal. Defaults to EMPTY for the FIFO selected by the FIFOADR[1:0] pins. 66 51 CTL3 O/Z H CTL3 is a GPIF control output. 67 52 CTL4 Output H CTL4 is a GPIF control output. 98 76 CTL5 Output H CTL5 is a GPIF control output. Document #: 38-08039 Rev. *B I Multiplexed pin whose function is selected by the PORTECFG.7 bit. (PE7) PE7 is a bidirectional I/O port pin. GPIFADR8 is a GPIF address output pin. Page 20 of 50 CY7C64713/14 Table 5-1. FX1 Pin Definitions (continued)[8] 128 100 56 TQFP TQFP QFN Type Default Description IFCLK I/O/Z Z Interface Clock, used for synchronously clocking data into or out of the slave FIFOs. IFCLK also serves as a timing reference for all slave FIFO control signals and GPIF. When internal clocking is used (IFCONFIG.7 = 1) the IFCLK pin can be configured to output 30/48 MHz by bits IFCONFIG.5 and IFCONFIG.6. IFCLK may be inverted, whether internally or externally sourced, by setting the bit IFCONFIG.4 =1. 22 INT4 Input N/A INT4 is the 8051 INT4 interrupt request input signal. The INT4 pin is edgesensitive, active HIGH. 106 84 INT5# Input N/A INT5# is the 8051 INT5 interrupt request input signal. The INT5 pin is edgesensitive, active LOW. 31 25 T2 Input N/A T2 is the active-HIGH T2 input signal to 8051 Timer2, which provides the input to Timer2 when C/T2 = 1. When C/T2 = 0, Timer2 does not use this pin. 30 24 T1 Input N/A T1 is the active-HIGH T1 signal for 8051 Timer1, which provides the input to Timer1 when C/T1 is 1. When C/T1 is 0, Timer1 does not use this bit. 29 23 T0 Input N/A T0 is the active-HIGH T0 signal for 8051 Timer0, which provides the input to Timer0 when C/T0 is 1. When C/T0 is 0, Timer0 does not use this bit. 53 43 RXD1 Input N/A RXD1is an active-HIGH input signal for 8051 UART1, which provides data to the UART in all modes. 52 42 TXD1 Output H TXD1is an active-HIGH output pin from 8051 UART1, which provides the output clock in sync mode, and the output data in async mode. 51 41 RXD0 Input N/A RXD0 is the active-HIGH RXD0 input to 8051 UART0, which provides data to the UART in all modes. 50 40 TXD0 Output H TXD0 is the active-HIGH TXD0 output from 8051 UART0, which provides the output clock in sync mode, and the output data in async mode. 32 26 28 13 42 Name CS# Output H CS# is the active-LOW chip select for external memory. 41 32 WR# Output H WR# is the active-LOW write strobe output for external memory. 40 31 RD# Output H RD# is the active-LOW read strobe output for external memory. OE# Output H OE# is the active-LOW output enable for external memory. 38 33 27 14 Reserved Input N/A Reserved. Connect to ground. 101 79 44 WAKEUP Input N/A USB Wakeup. If the 8051 is in suspend, asserting this pin starts up the oscillator and interrupts the 8051 to allow it to exit the suspend mode. Holding WAKEUP asserted inhibits the EZ-USB FX1 chip from suspending. This pin has programmable polarity (WAKEUP.4). 36 29 15 SCL OD Z Clock for the I2C interface. Connect to VCC with a 2.2K resistor, even if no I2C peripheral is attached. 37 30 16 SDA OD Z Data for I2C interface. Connect to VCC with a 2.2K resistor, even if no I2C peripheral is attached. 2 1 55 VCC Power N/A VCC. Connect to 3.3V power source. 26 20 11 VCC Power N/A VCC. Connect to 3.3V power source. 43 33 17 VCC Power N/A VCC. Connect to 3.3V power source. 48 38 VCC Power N/A VCC. Connect to 3.3V power source. 64 49 VCC Power N/A VCC. Connect to 3.3V power source. 68 53 VCC Power N/A VCC. Connect to 3.3V power source. 81 66 32 VCC Power N/A VCC. Connect to 3.3V power source. 100 78 43 VCC Power N/A VCC. Connect to 3.3V power source. 107 85 VCC Power N/A VCC. Connect to 3.3V power source. 27 Document #: 38-08039 Rev. *B Page 21 of 50 CY7C64713/14 Table 5-1. FX1 Pin Definitions (continued)[8] 128 100 56 TQFP TQFP QFN Name Type Description Default 3 2 56 GND Ground N/A Ground. 27 21 12 GND Ground N/A Ground. 49 39 58 48 26 65 50 28 80 65 93 75 116 94 125 99 14 15 16 41 GND Ground N/A Ground. GND Ground N/A Ground. GND Ground N/A Ground. GND Ground N/A Ground. GND Ground N/A Ground. GND Ground N/A Ground. GND Ground N/A Ground. 13 NC N/A N/A No Connect. This pin must be left open. 14 NC N/A N/A No Connect. This pin must be left open. 15 NC N/A N/A No-connect. This pin must be left open. 53 Document #: 38-08039 Rev. *B Page 22 of 50 CY7C64713/14 6.0 Register Summary FX1 register bit definitions are described in the EZ-USB TRM in greater detail. Table 6-1. FX1 Register Summary Hex E400 E480 E600 E601 E602 E603 E604 E605 E606 E607 E608 E609 E60A Size Name Description b7 GPIF Waveform Memories 128 WAVEDATA GPIF Waveform D7 Descriptor 0, 1, 2, 3 data 128 reserved GENERAL CONFIGURATION 1 CPUCS CPU Control & Status 0 1 IFCONFIG Interface Configuration IFCLKSRC (Ports, GPIF, slave FIFOs) [9] 1 PINFLAGSAB Slave FIFO FLAGA and FLAGB3 FLAGB Pin Configuration 1 PINFLAGSCD[9] Slave FIFO FLAGC and FLAGD3 FLAGD Pin Configuration 1 FIFORESET[9] Restore FIFOS to default NAKALL state 1 BREAKPT Breakpoint Control 0 1 BPADDRH Breakpoint Address H A15 1 BPADDRL Breakpoint Address L A7 1 UART230 230 Kbaud internally 0 generated ref. clock 1 FIFOPINPOLAR[9] Slave FIFO Interface pins 0 polarity 1 REVID Chip Revision rv7 E60B 1 E60C 1 3 E610 1 E611 1 E612 E613 E614 E615 1 1 1 1 2 E618 1 E619 1 E61A 1 E61B 1 E61C 4 E620 1 E621 1 E622 1 E623 1 E624 1 E625 1 E626 1 E627 1 E628 E629 E62A E62B E62C E62D E62E 1 1 1 1 1 1 1 REVCTL[9] Chip Revision Control UDMA GPIFHOLDAMOUNT MSTB Hold Time (for UDMA) reserved ENDPOINT CONFIGURATION EP1OUTCFG Endpoint 1-OUT Configuration EP1INCFG Endpoint 1-IN Configuration EP2CFG Endpoint 2 Configuration EP4CFG Endpoint 4 Configuration EP6CFG Endpoint 6 Configuration EP8CFG Endpoint 8 Configuration reserved EP2FIFOCFG[9] Endpoint 2 / slave FIFO configuration [9] EP4FIFOCFG Endpoint 4 / slave FIFO configuration EP6FIFOCFG[9] Endpoint 6 / slave FIFO configuration EP8FIFOCFG[9] Endpoint 8 / slave FIFO configuration reserved EP2AUTOINLENH[9] Endpoint 2 AUTOIN Packet Length H EP2AUTOINLENL[9] Endpoint 2 AUTOIN Packet Length L EP4AUTOINLENH[9] Endpoint 4 AUTOIN Packet Length H EP4AUTOINLENL[9] Endpoint 4 AUTOIN Packet Length L EP6AUTOINLENH[9] Endpoint 6 AUTOIN Packet Length H EP6AUTOINLENL[9] Endpoint 6 AUTOIN Packet Length L EP8AUTOINLENH[9] Endpoint 8 AUTOIN Packet Length H EP8AUTOINLENL[9] Endpoint 8 AUTOIN Packet Length L ECCCFG ECC Configuration ECCRESET ECC Reset ECC1B0 ECC1 Byte 0 Address ECC1B1 ECC1 Byte 1 Address ECC1B2 ECC1 Byte 2 Address ECC2B0 ECC2 Byte 0 Address ECC2B1 ECC2 Byte 1 Address b6 b5 b4 b3 b2 b1 b0 Default Access D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW 0 3048MHZ PORTCSTB CLKSPD1 IFCLKOE IFCLKPOL CLKSPD0 ASYNC CLKINV GSTATE CLKOE IFCFG1 8051RES IFCFG0 00000010 rrbbbbbr 10000000 RW FLAGB2 FLAGB1 FLAGB0 FLAGA3 FLAGA2 FLAGA1 FLAGA0 00000000 RW FLAGD2 FLAGD1 FLAGD0 FLAGC3 FLAGC2 FLAGC1 FLAGC0 00000000 RW 0 0 0 EP3 EP2 EP1 EP0 xxxxxxxx W 0 A14 A6 0 0 A13 A5 0 0 A12 A4 0 BREAK A11 A3 0 BPPULSE A10 A2 0 BPEN A9 A1 230UART1 0 A8 A0 230UART0 00000000 xxxxxxxx xxxxxxxx 00000000 rrrrbbbr RW RW rrrrrrbb 0 PKTEND SLOE SLRD SLWR EF FF 00000000 rrbbbbbb rv6 rv5 rv4 rv3 rv2 rv1 rv0 0 0 0 0 0 0 dyn_out enh_pkt RevA R 00000001 00000000 rrrrrrbb 0 0 0 0 0 0 HOLDTIME1 HOLDTIME0 00000000 rrrrrrbb VALID 0 TYPE1 TYPE0 0 0 0 0 10100000 brbbrrrr VALID 0 TYPE1 TYPE0 0 0 0 0 10100000 brbbrrrr VALID VALID VALID VALID DIR DIR DIR DIR TYPE1 TYPE1 TYPE1 TYPE1 TYPE0 TYPE0 TYPE0 TYPE0 SIZE 0 SIZE 0 0 0 0 0 BUF1 0 BUF1 0 BUF0 0 BUF0 0 10100010 10100000 11100010 11100000 0 INFM1 OEP1 AUTOOUT AUTOIN ZEROLENIN 0 WORDWIDE 00000101 rbbbbbrb 0 INFM1 OEP1 AUTOOUT AUTOIN ZEROLENIN 0 WORDWIDE 00000101 rbbbbbrb 0 INFM1 OEP1 AUTOOUT AUTOIN ZEROLENIN 0 WORDWIDE 00000101 rbbbbbrb 0 INFM1 OEP1 AUTOOUT AUTOIN ZEROLENIN 0 WORDWIDE 00000101 rbbbbbrb 0 0 0 0 0 PL10 PL9 PL8 00000010 rrrrrbbb PL7 PL6 PL5 PL4 PL3 PL2 PL1 PL0 00000000 RW 0 0 0 0 0 0 PL9 PL8 00000010 rrrrrrbb PL7 PL6 PL5 PL4 PL3 PL2 PL1 PL0 00000000 RW 0 0 0 0 0 PL10 PL9 PL8 00000010 rrrrrbbb PL7 PL6 PL5 PL4 PL3 PL2 PL1 PL0 00000000 RW 0 0 0 0 0 0 PL9 PL8 00000010 rrrrrrbb PL7 PL6 PL5 PL4 PL3 PL2 PL1 PL0 00000000 RW 0 x LINE15 LINE7 COL5 LINE15 LINE7 0 x LINE14 LINE6 COL4 LINE14 LINE6 0 x LINE13 LINE5 COL3 LINE13 LINE5 0 x LINE12 LINE4 COL2 LINE12 LINE4 0 x LINE11 LINE3 COL1 LINE11 LINE3 0 x LINE10 LINE2 COL0 LINE10 LINE2 0 x LINE9 LINE1 LINE17 LINE9 LINE1 ECCM x LINE8 LINE0 LINE16 LINE8 LINE0 00000000 00000000 11111111 11111111 11111111 11111111 11111111 bbbbbrbb bbbbrrrr bbbbbrbb bbbbrrrr rrrrrrrb W R R R R R Note: 9. Read and writes to these register may require synchronization delay, see Technical Reference Manual for “Synchronization Delay.” Document #: 38-08039 Rev. *B Page 23 of 50 CY7C64713/14 Table 6-1. FX1 Register Summary (continued) Hex Size Name E62F 1 ECC2B2 Description ECC2 Byte 2 Address b7 COL5 b6 COL4 b5 COL3 Endpoint 2 / slave FIFO DECIS Programmable Flag H ISO Mode Endpoint 2 / slave FIFO DECIS Programmable Flag H Non-ISO Mode PKTSTAT b4 COL2 b3 COL1 b2 COL0 b1 0 b0 0 Default 11111111 Access R IN: PKTS[2] IN: PKTS[1] IN: PKTS[0] 0 OUT:PFC12 OUT:PFC11 OUT:PFC10 PFC9 PFC8 10001000 bbbbbrbb PKTSTAT OUT:PFC12 OUT:PFC11 OUT:PFC10 0 PFC9 IN:PKTS[2] OUT:PFC8 10001000 bbbbbrbb IN:PKTS[0] OUT:PFC6 PFC5 PFC4 PFC1 PFC0 00000000 RW PKTSTAT 0 IN: PKTS[1] IN: PKTS[0] 0 OUT:PFC10 OUT:PFC9 0 PFC8 10001000 bbrbbrrb PKTSTAT 0 OUT:PFC10 OUT:PFC9 0 0 PFC8 10001000 bbrbbrrb PFC4 PFC1 PFC0 00000000 RW E630 1 EP2FIFOPFH[9] E630 1 EP2FIFOPFH[9] E631 1 EP2FIFOPFL[9] Endpoint 2 / slave FIFO Programmable Flag L E632 1 EP4FIFOPFH[9] E632 1 EP4FIFOPFH[9] Endpoint 4 / slave FIFO DECIS Programmable Flag H ISO Mode Endpoint 4 / slave FIFO DECIS Programmable Flag H Non-ISO Mode E633 1 EP4FIFOPFL[9] Endpoint 4 / slave FIFO Programmable Flag L E634 1 EP6FIFOPFH[9] PKTSTAT INPKTS[2] IN: PKTS[1] IN: PKTS[0] 0 OUT:PFC12 OUT:PFC11 OUT:PFC10 PFC9 PFC8 00001000 bbbbbrbb E634 1 EP6FIFOPFH[9] Endpoint 6 / slave FIFO DECIS Programmable Flag H ISO Mode Endpoint 6 / slave FIFO DECIS Programmable Flag H Non-ISO Mode PKTSTAT OUT:PFC12 OUT:PFC11 OUT:PFC10 0 PFC9 IN:PKTS[2] OUT:PFC8 00001000 bbbbbrbb E635 1 EP6FIFOPFL[9] Endpoint 6 / slave FIFO Programmable Flag L IN:PKTS[0] OUT:PFC6 PFC5 PFC4 PFC1 PFC0 00000000 RW E636 1 EP8FIFOPFH[9] PKTSTAT 0 IN: PKTS[1] IN: PKTS[0] 0 OUT:PFC10 OUT:PFC9 0 PFC8 00001000 bbrbbrrb E636 1 EP8FIFOPFH[9] Endpoint 8 / slave FIFO DECIS Programmable Flag H ISO Mode Endpoint 8 / slave FIFO DECIS Programmable Flag H Non-ISO Mode PKTSTAT 0 OUT:PFC10 OUT:PFC9 0 0 PFC8 00001000 bbrbbrrb E637 1 Endpoint 8 / slave FIFO Programmable Flag L Endpoint 8 / slave FIFO Programmable Flag L PFC7 PFC6 PFC5 PFC4 PFC3 PFC2 PFC1 PFC0 00000000 RW IN: PKTS[1] IN: PKTS[0] PFC5 OUT:PFC7 OUT:PFC6 PFC4 PFC3 PFC2 PFC1 PFC0 00000000 RW Force IN Packet End Force OUT Packet End Skip Skip 0 0 0 0 0 0 EP3 EP3 EP2 EP2 EP1 EP1 EP0 EP0 xxxxxxxx xxxxxxxx E650 1 EP8FIFOPFL[9] ISO Mode EP8FIFOPFL[9] Non-ISO Mode reserved reserved reserved reserved reserved reserved INPKTEND[9] OUTPKTEND[9] INTERRUPTS EP2FIFOIE[9] 0 0 0 EDGEPF PF EF FF 00000000 RW E651 1 0 0 0 0 0 PF EF FF 00000111 rrrrrbbb E652 1 EP4FIFOIE[9] 0 0 0 0 EDGEPF PF EF FF 00000000 RW E653 1 EP4FIFOIRQ[9,10] 0 0 0 0 0 PF EF FF 00000111 rrrrrbbb E654 1 EP6FIFOIE[9] 0 0 0 0 EDGEPF PF EF FF 00000000 RW E655 1 EP6FIFOIRQ[9,10] 0 0 0 0 0 PF EF FF 00000110 rrrrrbbb E656 1 EP8FIFOIE[9] 0 0 0 0 EDGEPF PF EF FF 00000000 RW E657 1 EP8FIFOIRQ[9,10] 0 0 0 0 0 PF EF FF 00000110 rrrrrbbb E658 1 IBNIE Endpoint 2 slave FIFO Flag Interrupt Enable Endpoint 2 slave FIFO Flag Interrupt Request Endpoint 4 slave FIFO Flag Interrupt Enable Endpoint 4 slave FIFO Flag Interrupt Request Endpoint 6 slave FIFO Flag Interrupt Enable Endpoint 6 slave FIFO Flag Interrupt Request Endpoint 8 slave FIFO Flag Interrupt Enable Endpoint 8 slave FIFO Flag Interrupt Request IN-BULK-NAK Interrupt Enable 0 EP2FIFOIRQ[9,10] 0 0 EP8 EP6 EP4 EP2 EP1 EP0 00000000 RW E637 1 E640 E641 E642 E643 E644 E648 E649 8 1 1 1 1 4 1 7 IN:PKTS[1] OUT:PFC7 IN: PKTS[1] IN: PKTS[0] PFC5 OUT:PFC7 OUT:PFC6 IN:PKTS[1] OUT:PFC7 PFC3 PFC3 PFC3 PFC2 PFC2 PFC2 W W Note: 10. SFRs not part of the standard 8051 architecture. The register can only be reset, it cannot be set. Document #: 38-08039 Rev. *B Page 24 of 50 CY7C64713/14 Table 6-1. FX1 Register Summary (continued) Hex Size Name E659 1 IBNIRQ[10] E65A 1 NAKIE E65B 1 NAKIRQ[10] E65C 1 E65D 1 E65E 1 USBIE USBIRQ[10] EPIE E65F 1 EPIRQ[10] E660 1 E661 1 E662 1 GPIFIE[9] GPIFIRQ[9] USBERRIE E663 1 USBERRIRQ[10] E664 1 ERRCNTLIM E665 1 E666 1 CLRERRCNT INT2IVEC E667 1 INT4IVEC E668 1 E669 7 E670 1 INTSETUP reserved INPUT / OUTPUT PORTACFG E671 1 PORTCCFG E672 1 PORTECFG E673 4 E677 1 E678 1 XTALINSRC reserved I2CS E679 1 I2DAT E67A 1 I2CTL E67B 1 XAUTODAT1 E67C 1 XAUTODAT2 E680 E681 E682 E683 E684 E685 E686 E687 E688 1 1 1 1 1 1 1 1 2 UDMA CRC UDMACRCH[9] UDMACRCL[9] UDMACRCQUALIFIER USB CONTROL USBCS SUSPEND WAKEUPCS TOGCTL USBFRAMEH USBFRAMEL reserved FNADDR reserved E68A E68B E68C E68D 1 1 1 1 ENDPOINTS EP0BCH[9] EP0BCL[9] reserved EP1OUTBC E68E E68F E690 E691 E692 E694 E695 E696 1 1 1 1 2 1 1 2 reserved EP1INBC EP2BCH[9] EP2BCL[9] reserved EP4BCH[9] EP4BCL[9] reserved E67D 1 E67E 1 E67F 1 Description b7 IN-BULK-NAK interrupt 0 Request Endpoint Ping-NAK / IBN EP8 Interrupt Enable Endpoint Ping-NAK / IBN EP8 Interrupt Request USB Int Enables 0 USB Interrupt Requests 0 Endpoint Interrupt EP8 Enables Endpoint Interrupt EP8 Requests GPIF Interrupt Enable 0 GPIF Interrupt Request 0 USB Error Interrupt ISOEP8 Enables USB Error Interrupt ISOEP8 Requests USB Error counter and EC3 limit Clear Error Counter EC3:0 x Interrupt 2 (USB) 0 Autovector Interrupt 4 (slave FIFO & 1 GPIF) Autovector Interrupt 2&4 setup 0 b6 0 b5 EP8 b4 EP6 b3 EP4 b2 EP2 b1 EP1 b0 EP0 Default Access 00xxxxxx rrbbbbbb EP6 EP4 EP2 EP1 EP0 0 IBN 00000000 RW EP6 EP4 EP2 EP1 EP0 0 IBN xxxxxx0x bbbbbbrb EP0ACK EP0ACK EP6 0 0 EP4 URES URES EP2 SUSP SUSP EP1OUT SUTOK SUTOK EP1IN SOF SOF EP0OUT SUDAV SUDAV EP0IN 00000000 RW 0xxxxxxx rbbbbbbb 00000000 RW EP6 EP4 EP2 EP1OUT EP1IN EP0OUT EP0IN 0 0 0 ISOEP6 0 0 ISOEP4 0 0 ISOEP2 0 0 0 0 0 0 GPIFWF GPIFWF 0 GPIFDONE 00000000 RW GPIFDONE 000000xx RW ERRLIMIT 00000000 RW ISOEP6 ISOEP4 ISOEP2 0 0 0 ERRLIMIT 0000000x bbbbrrrb EC2 EC1 EC0 LIMIT3 LIMIT2 LIMIT1 LIMIT0 xxxx0100 rrrrbbbb x I2V4 x I2V3 x I2V2 x I2V1 x I2V0 x 0 x 0 xxxxxxxx W 00000000 R 0 I4V3 I4V2 I4V1 I4V0 0 0 10000000 R 0 0 0 AV2EN 0 INT4SRC AV4EN 00000000 RW I/O PORTA Alternate Configuration I/O PORTC Alternate Configuration I/O PORTE Alternate Configuration XTALIN Clock Source FLAGD SLCS 0 0 0 0 INT1 INT0 00000000 RW GPIFA7 GPIFA6 GPIFA5 GPIFA4 GPIFA3 GPIFA2 GPIFA1 GPIFA0 00000000 RW GPIFA8 T2EX INT6 RXD1OUT RXD0OUT T2OUT T1OUT T0OUT 00000000 RW 0 0 0 0 0 0 0 EXTCLK 00000000 rrrrrrrb I²C Bus Control & Status I²C Bus Data I²C Bus Control Autoptr1 MOVX access, when APTREN=1 Autoptr2 MOVX access, when APTREN=1 START STOP LASTRD ID1 ID0 BERR ACK DONE 000xx000 bbbrrrrr d7 d6 d5 d4 d3 d2 d1 d0 xxxxxxxx 0 0 0 0 0 0 STOPIE 400KHZ 00000000 RW D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW UDMA CRC MSB UDMA CRC LSB UDMA CRC Qualifier CRC15 CRC7 QENABLE CRC14 CRC6 0 CRC13 CRC5 0 CRC12 CRC4 0 CRC11 CRC3 QSTATE CRC10 CRC2 QSIGNAL2 CRC9 CRC1 QSIGNAL1 CRC8 CRC0 QSIGNAL0 01001010 RW 10111010 RW 00000000 brrrbbbb USB Control & Status Put chip into suspend Wakeup Control & Status Toggle Control USB Frame count H USB Frame count L 0 x WU2 Q 0 FC7 0 x WU S 0 FC6 0 x WU2POL R 0 FC5 0 x WUPOL IO 0 FC4 DISCON x 0 EP3 0 FC3 NOSYNSOF x DPEN EP2 FC10 FC2 RENUM x WU2EN EP1 FC9 FC1 SIGRSUME x WUEN EP0 FC8 FC0 x0000000 xxxxxxxx xx000101 x0000000 00000xxx xxxxxxxx USB Function address 0 FA6 FA5 FA4 FA3 FA2 FA1 FA0 0xxxxxxx R Endpoint 0 Byte Count H (BC15) Endpoint 0 Byte Count L (BC7) (BC14) BC6 (BC13) BC5 (BC12) BC4 (BC11) BC3 (BC10) BC2 (BC9) BC1 (BC8) BC0 xxxxxxxx xxxxxxxx RW RW Endpoint 1 OUT Byte Count BC6 BC5 BC4 BC3 BC2 BC1 BC0 xxxxxxxx RW Endpoint 1 IN Byte Count 0 Endpoint 2 Byte Count H 0 Endpoint 2 Byte Count L BC7/SKIP BC6 0 BC6 BC5 0 BC5 BC4 0 BC4 BC3 0 BC3 BC2 BC10 BC2 BC1 BC9 BC1 BC0 BC8 BC0 xxxxxxxx xxxxxxxx xxxxxxxx RW RW RW Endpoint 4 Byte Count H 0 Endpoint 4 Byte Count L BC7/SKIP 0 BC6 0 BC5 0 BC4 0 BC3 0 BC2 BC9 BC1 BC8 BC0 xxxxxxxx xxxxxxxx RW RW Document #: 38-08039 Rev. *B 0 RW RW rrrrbbbb W bbbbrbbb rrrbbbbb R R Page 25 of 50 CY7C64713/14 Table 6-1. FX1 Register Summary (continued) Hex E698 E699 E69A E69C E69D E69E E6A0 Size 1 1 2 1 1 2 1 Name EP6BCH[9] EP6BCL[9] reserved EP8BCH[9] EP8BCL[9] reserved EP0CS E6A1 1 EP1OUTCS E6A2 1 EP1INCS E6A3 1 EP2CS E6A4 1 EP4CS E6A5 1 EP6CS E6A6 1 EP8CS E6A7 1 EP2FIFOFLGS E6A8 1 EP4FIFOFLGS E6A9 1 EP6FIFOFLGS E6AA 1 EP8FIFOFLGS E6AB 1 EP2FIFOBCH E6AC 1 EP2FIFOBCL E6AD 1 EP4FIFOBCH E6AE 1 EP4FIFOBCL E6AF 1 EP6FIFOBCH E6B0 1 EP6FIFOBCL E6B1 1 EP8FIFOBCH E6B2 1 EP8FIFOBCL E6B3 1 SUDPTRH E6B4 1 SUDPTRL E6B5 1 SUDPTRCTL 2 E6B8 8 reserved SETUPDAT E6C0 1 E6C1 1 GPIF GPIFWFSELECT GPIFIDLECS E6C2 E6C3 E6C4 E6C5 1 1 1 1 E6C6 1 GPIFIDLECTL GPIFCTLCFG GPIFADRH[9] GPIFADRL[9] FLOWSTATE FLOWSTATE E6C7 1 E6C8 1 FLOWLOGIC FLOWEQ0CTL E6C9 1 FLOWEQ1CTL E6CA 1 FLOWHOLDOFF Description b7 Endpoint 6 Byte Count H 0 Endpoint 6 Byte Count L BC7/SKIP b6 0 BC6 b5 0 BC5 b4 0 BC4 b3 0 BC3 b2 BC10 BC2 b1 BC9 BC1 b0 BC8 BC0 Default xxxxxxxx xxxxxxxx Access RW RW Endpoint 8 Byte Count H 0 Endpoint 8 Byte Count L BC7/SKIP 0 BC6 0 BC5 0 BC4 0 BC3 0 BC2 BC9 BC1 BC8 BC0 xxxxxxxx xxxxxxxx RW RW Endpoint 0 Control and HSNAK Status Endpoint 1 OUT Control 0 and Status Endpoint 1 IN Control and 0 Status Endpoint 2 Control and 0 Status Endpoint 4 Control and 0 Status Endpoint 6 Control and 0 Status Endpoint 8 Control and 0 Status Endpoint 2 slave FIFO 0 Flags Endpoint 4 slave FIFO 0 Flags Endpoint 6 slave FIFO 0 Flags Endpoint 8 slave FIFO 0 Flags Endpoint 2 slave FIFO 0 total byte count H Endpoint 2 slave FIFO BC7 total byte count L Endpoint 4 slave FIFO 0 total byte count H Endpoint 4 slave FIFO BC7 total byte count L Endpoint 6 slave FIFO 0 total byte count H Endpoint 6 slave FIFO BC7 total byte count L Endpoint 8 slave FIFO 0 total byte count H Endpoint 8 slave FIFO BC7 total byte count L Setup Data Pointer high A15 address byte Setup Data Pointer low ad- A7 dress byte Setup Data Pointer Auto 0 Mode 0 0 0 0 0 BUSY STALL 10000000 bbbbbbrb 0 0 0 0 0 BUSY STALL 00000000 bbbbbbrb 0 0 0 0 0 BUSY STALL 00000000 bbbbbbrb NPAK2 NPAK1 NPAK0 FULL EMPTY 0 STALL 00101000 rrrrrrrb 0 NPAK1 NPAK0 FULL EMPTY 0 STALL 00101000 rrrrrrrb NPAK2 NPAK1 NPAK0 FULL EMPTY 0 STALL 00000100 rrrrrrrb 0 NPAK1 NPAK0 FULL EMPTY 0 STALL 00000100 rrrrrrrb 0 0 0 0 PF EF FF 00000010 R 0 0 0 0 PF EF FF 00000010 R 0 0 0 0 PF EF FF 00000110 R 0 0 0 0 PF EF FF 00000110 R 0 0 BC12 BC11 BC10 BC9 BC8 00000000 R BC6 BC5 BC4 BC3 BC2 BC1 BC0 00000000 R 0 0 0 0 BC10 BC9 BC8 00000000 R BC6 BC5 BC4 BC3 BC2 BC1 BC0 00000000 R 0 0 0 BC11 BC10 BC9 BC8 00000000 R BC6 BC5 BC4 BC3 BC2 BC1 BC0 00000000 R 0 0 0 0 BC10 BC9 BC8 00000000 R BC6 BC5 BC4 BC3 BC2 BC1 BC0 00000000 R A14 A13 A12 A11 A10 A9 A8 xxxxxxxx A6 A5 A4 A3 A2 A1 0 xxxxxxx0 bbbbbbbr 0 0 0 0 0 0 SDPAUTO 00000001 RW 8 bytes of setup data D7 SETUPDAT[0] = bmRequestType SETUPDAT[1] = bmRequest SETUPDAT[2:3] = wValue SETUPDAT[4:5] = wIndex SETUPDAT[6:7] = wLength D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW R Waveform Selector GPIF Done, GPIF IDLE drive mode Inactive Bus, CTL states CTL Drive Type GPIF Address H GPIF Address L SINGLEWR1 SINGLEWR0 SINGLERD1 SINGLERD0 FIFOWR1 DONE 0 0 0 0 FIFOWR0 0 FIFORD1 0 FIFORD0 IDLEDRV 11100100 RW 10000000 RW 0 TRICTL 0 GPIFA7 0 0 0 GPIFA6 CTL5 CTL5 0 GPIFA5 CTL4 CTL4 0 GPIFA4 CTL3 CTL3 0 GPIFA3 CTL2 CTL2 0 GPIFA2 CTL1 CTL1 0 GPIFA1 CTL0 CTL0 GPIFA8 GPIFA0 11111111 00000000 00000000 00000000 Flowstate Enable and Selector Flowstate Logic CTL-Pin States in Flowstate (when Logic = 0) CTL-Pin States in Flowstate (when Logic = 1) Holdoff Configuration FSE 0 0 0 0 FS2 FS1 FS0 00000000 brrrrbbb LFUNC1 CTL0E3 LFUNC0 CTL0E2 TERMA2 CTL0E1/ CTL5 TERMA1 CTL0E0/ CTL4 TERMA0 CTL3 TERMB2 CTL2 TERMB1 CTL1 TERMB0 CTL0 00000000 RW 00000000 RW CTL0E3 CTL0E2 CTL2 CTL1 CTL0 00000000 RW HOCTL2 HOCTL1 HOCTL0 00000000 RW Document #: 38-08039 Rev. *B CTL0E1/ CTL0E0/ CTL3 CTL5 CTL4 HOPERIOD3 HOPERIOD2 HOPERIOD1 HOPERIOD HOSTATE 0 RW RW RW RW Page 26 of 50 CY7C64713/14 Table 6-1. FX1 Register Summary (continued) Hex Size Name E6CB 1 FLOWSTB E6CC 1 FLOWSTBEDGE E6CD 1 E6CE 1 FLOWSTBPERIOD GPIFTCB3[9] E6CF 1 GPIFTCB2[9] E6D0 1 GPIFTCB1[9] E6D1 1 [9] 2 E6D2 1 GPIFTCB0 Description b7 Flowstate Strobe SLAVE Configuration Flowstate Rising/Falling 0 Edge Configuration Master-Strobe Half-Period D7 GPIF Transaction Count TC31 Byte 3 GPIF Transaction Count TC23 Byte 2 GPIF Transaction Count TC15 Byte 1 GPIF Transaction Count TC7 Byte 0 reserved reserved reserved EP2GPIFFLGSEL[9] Endpoint 2 GPIF Flag select EP2GPIFPFSTOP Endpoint 2 GPIF stop transaction on prog. flag EP2GPIFTRIG[9] Endpoint 2 GPIF Trigger reserved reserved reserved EP4GPIFFLGSEL[9] Endpoint 4 GPIF Flag select EP4GPIFPFSTOP Endpoint 4 GPIF stop transaction on GPIF Flag EP4GPIFTRIG[9] Endpoint 4 GPIF Trigger reserved reserved reserved EP6GPIFFLGSEL[9] Endpoint 6 GPIF Flag select EP6GPIFPFSTOP Endpoint 6 GPIF stop transaction on prog. flag EP6GPIFTRIG[9] Endpoint 6 GPIF Trigger reserved reserved reserved EP8GPIFFLGSEL[9] Endpoint 8 GPIF Flag select EP8GPIFPFSTOP Endpoint 8 GPIF stop transaction on prog. flag EP8GPIFTRIG[9] Endpoint 8 GPIF Trigger reserved XGPIFSGLDATH GPIF Data H (16-bit mode only) XGPIFSGLDATLX Read/Write GPIF Data L & trigger transaction XGPIFSGLDATLRead GPIF Data L, no NOX transaction trigger GPIFREADYCFG Internal RDY, Sync/Async, RDY pin states b6 b5 RDYASYNC CTLTOGL b4 SUSTAIN b3 0 b2 MSTB2 b1 MSTB1 b0 MSTB0 Default Access 00100000 RW 0 0 0 0 0 FALLING RISING 00000001 rrrrrrbb D6 TC30 D5 TC29 D4 TC28 D3 TC27 D2 TC26 D1 TC25 D0 TC24 00000010 RW 00000000 RW TC22 TC21 TC20 TC19 TC18 TC17 TC16 00000000 RW TC14 TC13 TC12 TC11 TC10 TC9 TC8 00000000 RW TC6 TC5 TC4 TC3 TC2 TC1 TC0 00000001 RW 00000000 RW 0 0 0 0 0 0 FS1 FS0 0 0 0 0 0 0 0 FIFO2FLAG 00000000 RW x x x x x x x x xxxxxxxx 0 0 0 0 0 0 FS1 FS0 00000000 RW 0 0 0 0 0 0 0 FIFO4FLAG 00000000 RW x x x x x x x x xxxxxxxx 0 0 0 0 0 0 FS1 FS0 00000000 RW 0 0 0 0 0 0 0 FIFO6FLAG 00000000 RW x x x x x x x x xxxxxxxx 0 0 0 0 0 0 FS1 FS0 00000000 RW 0 0 0 0 0 0 0 FIFO8FLAG 00000000 RW x x x x x x x x xxxxxxxx W D15 D14 D13 D12 D11 D10 D9 D8 xxxxxxxx RW D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx R INTRDY SAS TCXRDY5 0 0 0 0 0 00000000 bbbrrrrr E6F4 1 E6F5 1 E6F6 2 0 x 0 x RDY5 x RDY4 x RDY3 x RDY2 x RDY1 x RDY0 x 00xxxxxx R xxxxxxxx W E740 E780 E7C0 D7 D7 D7 D6 D6 D6 D5 D5 D5 D4 D4 D4 D3 D3 D3 D2 D2 D2 D1 D1 D1 D0 D0 D0 xxxxxxxx xxxxxxxx xxxxxxxx D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW RW RW RW RW D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW 0 DISCON 0 0 0 0 0 400KHZ xxxxxxxx n/a D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW E6D3 1 E6D4 1 3 E6DA 1 E6DB 1 E6DC 1 3 E6E2 1 E6E3 1 E6E4 1 3 E6EA 1 E6EB 1 E6EC 1 3 E6F0 1 E6F1 1 E6F2 1 E6F3 1 FE00 xxxx GPIFREADYSTAT GPIF Ready Status GPIFABORT Abort GPIF Waveforms reserved ENDPOINT BUFFERS 64 EP0BUF EP0-IN/-OUT buffer 64 EP10UTBUF EP1-OUT buffer 64 EP1INBUF EP1-IN buffer 2048 reserved 1023 EP2FIFOBUF 64/1023-byte EP 2 / slave FIFO buffer (IN or OUT) 64 EP4FIFOBUF 64 byte EP 4 / slave FIFO buffer (IN or OUT) 64 reserved 1023 EP6FIFOBUF 64/1023-byte EP 6 / slave FIFO buffer (IN or OUT) 64 EP8FIFOBUF 64 byte EP 8 / slave FIFO buffer (IN or OUT) 64 reserved I²C Configuration Byte 80 1 F000 F400 F600 F800 FC00 Special Function Registers (SFRs) IOA[10] Port A (bit addressable) Document #: 38-08039 Rev. *B 00000000 RW [[11]] W W W Page 27 of 50 CY7C64713/14 Table 6-1. FX1 Register Summary (continued) Hex 81 82 83 84 85 86 87 88 Size 1 1 1 1 1 1 1 1 Name SP DPL0 DPH0 DPL1[10] DPH1[10] DPS[10] PCON TCON 89 1 TMOD 8A 8B 8C 8D 8E 8F 90 91 92 1 1 1 1 1 1 1 1 1 TL0 TL1 TH0 TH1 CKCON[10] reserved IOB[10] EXIF[10] MPAGE[10] 93 98 5 1 reserved SCON0 99 9A 9B 9C 9D 9E 9F A0 A1 A2 A3 A8 1 1 1 1 1 1 1 1 1 1 5 1 SBUF0 AUTOPTRH1[10] AUTOPTRL1[10] reserved AUTOPTRH2[10] AUTOPTRL2[10] reserved IOC[10] INT2CLR[10] INT4CLR[10] reserved IE A9 AA 1 1 reserved EP2468STAT[10] AB 1 EP24FIFOFLGS AC 1 EP68FIFOFLGS AD AF B0 B1 2 1 1 1 B2 B3 B4 B5 B6 B7 B8 1 1 1 1 1 1 1 B9 BA 1 1 reserved AUTOPTRSETUP[10] Autopointer 1&2 setup IOD[10] Port D (bit addressable) IOE[10] Port E (NOT bit addressable) [10] OEA Port A Output Enable OEB[10] Port B Output Enable [10] OEC Port C Output Enable OED[10] Port D Output Enable OEE[10] Port E Output Enable reserved IP Interrupt Priority (bit addressable) reserved [10] EP01STAT Endpoint 0&1 Status BB 1 GPIFTRIG[10] [9] BC BD 1 1 reserved GPIFSGLDATH[10] BE BF 1 1 GPIFSGLDATLX[10] C0 1 GPIFSGLDAT LNOX[10] SCON1[10] C1 C2 1 6 SBUF1[10] reserved [10] [10] Description Stack Pointer Data Pointer 0 L Data Pointer 0 H Data Pointer 1 L Data Pointer 1 H Data Pointer 0/1 select Power Control Timer/Counter Control (bit addressable) Timer/Counter Mode Control Timer 0 reload L Timer 1 reload L Timer 0 reload H Timer 1 reload H Clock Control b7 D7 A7 A15 A7 A15 0 SMOD0 TF1 b6 D6 A6 A14 A6 A14 0 x TR1 b5 D5 A5 A13 A5 A13 0 1 TF0 b4 D4 A4 A12 A4 A12 0 1 TR0 b3 D3 A3 A11 A3 A11 0 x IE1 b2 D2 A2 A10 A2 A10 0 x IT1 b1 D1 A1 A9 A1 A9 0 x IE0 b0 D0 A0 A8 A0 A8 SEL IDLE IT0 Default 00000111 00000000 00000000 00000000 00000000 00000000 00110000 00000000 GATE CT M1 M0 GATE CT M1 M0 00000000 RW D7 D7 D15 D15 x D6 D6 D14 D14 x D5 D5 D13 D13 T2M D4 D4 D12 D12 T1M D3 D3 D11 D11 T0M D2 D2 D10 D10 MD2 D1 D1 D9 D9 MD1 D0 D0 D8 D8 MD0 00000000 00000000 00000000 00000000 00000001 Port B (bit addressable) D7 External Interrupt Flag(s) IE5 Upper Addr Byte of MOVX A15 using @R0 / @R1 D6 IE4 A14 D5 I²CINT A13 D4 USBNT A12 D3 1 A11 D2 0 A10 D1 0 A9 D0 0 A8 xxxxxxxx RW 00001000 RW 00000000 RW Serial Port 0 Control (bit addressable) Serial Port 0 Data Buffer Autopointer 1 Address H Autopointer 1 Address L SM0_0 SM1_0 SM2_0 REN_0 TB8_0 RB8_0 TI_0 RI_0 00000000 RW D7 A15 A7 D6 A14 A6 D5 A13 A5 D4 A12 A4 D3 A11 A3 D2 A10 A2 D1 A9 A1 D0 A8 A0 00000000 RW 00000000 RW 00000000 RW Autopointer 2 Address H A15 Autopointer 2 Address L A7 A14 A6 A13 A5 A12 A4 A11 A3 A10 A2 A9 A1 A8 A0 00000000 RW 00000000 RW Port C (bit addressable) Interrupt 2 clear Interrupt 4 clear D7 x x D6 x x D5 x x D4 x x D3 x x D2 x x D1 x x D0 x x xxxxxxxx xxxxxxxx xxxxxxxx Interrupt Enable (bit addressable) EA ES1 ET2 ES0 ET1 EX1 ET0 EX0 00000000 RW EP8E EP6F EP6E EP4F EP4E EP2F EP2E 01011010 R EP4PF EP4EF EP4FF 0 EP2PF EP2EF EP2FF 00100010 R EP8PF EP8EF EP8FF 0 EP6PF EP6EF EP6FF 01100110 R 0 D7 D7 0 D6 D6 0 D5 D5 0 D4 D4 0 D3 D3 APTR2INC D2 D2 APTR1INC D1 D1 APTREN D0 D0 00000110 RW xxxxxxxx RW xxxxxxxx RW D7 D7 D7 D7 D7 D6 D6 D6 D6 D6 D5 D5 D5 D5 D5 D4 D4 D4 D4 D4 D3 D3 D3 D3 D3 D2 D2 D2 D2 D2 D1 D1 D1 D1 D1 D0 D0 D0 D0 D0 00000000 00000000 00000000 00000000 00000000 1 PS1 PT2 PS0 PT1 PX1 PT0 PX0 10000000 RW 0 0 0 0 0 EP1INBSY 00000000 R DONE 0 0 0 0 RW EP1OUTBS EP0BSY Y EP1 EP0 GPIF Data H (16-bit mode D15 only) GPIF Data L w/ Trigger D7 GPIF Data L w/ No Trigger D7 D14 D13 D12 D11 D10 D9 D8 xxxxxxxx RW D6 D6 D5 D5 D4 D4 D3 D3 D2 D2 D1 D1 D0 D0 xxxxxxxx xxxxxxxx RW R Serial Port 1 Control (bit SM0_1 addressable) Serial Port 1 Data Buffer D7 SM1_1 SM2_1 REN_1 TB8_1 RB8_1 TI_1 RI_1 00000000 RW D6 D5 D4 D3 D2 D1 D0 00000000 RW Endpoint 2,4,6,8 status EP8F flags Endpoint 2,4 slave FIFO 0 status flags Endpoint 6,8 slave FIFO 0 status flags Endpoint 2,4,6,8 GPIF slave FIFO Trigger Access RW RW RW RW RW RW RW RW RW RW RW RW RW RW W W RW RW RW RW RW 10000xxx brrrrbbb Notes: 11. If no EEPROM is detected by the SIE then the default is 00000000. Document #: 38-08039 Rev. *B Page 28 of 50 CY7C64713/14 Table 6-1. FX1 Register Summary (continued) Hex C8 Size Name 1 T2CON C9 CA 1 1 reserved RCAP2L CB 1 RCAP2H CC CD CE D0 1 1 2 1 TL2 TH2 reserved PSW D1 D8 D9 E0 7 1 7 1 reserved EICON[10] reserved ACC E1 E8 7 1 reserved EIE[10] E9 F0 F1 F8 7 1 7 1 reserved B reserved EIP[10] F9 7 reserved Description Timer/Counter 2 Control (bit addressable) b7 TF2 b6 EXF2 b5 RCLK b4 TCLK b3 EXEN2 b2 TR2 b1 CT2 b0 CPRL2 Default Access 00000000 RW Capture for Timer 2, auto- D7 reload, up-counter Capture for Timer 2, auto- D7 reload, up-counter Timer 2 reload L D7 Timer 2 reload H D15 D6 D5 D4 D3 D2 D1 D0 00000000 RW D6 D5 D4 D3 D2 D1 D0 00000000 RW D6 D14 D5 D13 D4 D12 D3 D11 D2 D10 D1 D9 D0 D8 00000000 RW 00000000 RW Program Status Word (bit CY addressable) AC F0 RS1 RS0 OV F1 P 00000000 RW External Interrupt Control SMOD1 1 ERESI RESI INT6 0 0 0 01000000 RW Accumulator (bit address- D7 able) D6 D5 D4 D3 D2 D1 D0 00000000 RW External Interrupt Enable(s) 1 1 1 EX6 EX5 EX4 EI²C EUSB 11100000 RW B (bit addressable) D7 D6 D5 D4 D3 D2 D1 D0 00000000 RW 1 1 PX6 PX5 PX4 PI²C PUSB 11100000 RW External Interrupt Priority 1 Control R = all bits read-only W = all bits write-only r = read-only bit w = write-only bit b = both read/write bit Document #: 38-08039 Rev. *B Page 29 of 50 CY7C64713/14 7.0 Absolute Maximum Ratings Max Output Current, per I/O port................................ 10 mA Max Output Current, all five I/O ports (128- and 100-pin packages) ..................................... 50 mA Storage Temperature .................................. –65°C to +150°C Ambient Temperature with Power Supplied ...... 0°C to +70°C 8.0 Supply Voltage to Ground Potential ............... –0.5V to +4.0V [12] Operating Conditions DC Input Voltage to Any Input Pin .......................... 5.25V TA (Ambient Temperature Under Bias) ............. 0°C to +70°C DC Voltage Applied to Outputs in High-Z State ..................................... –0.5V to VCC + 0.5V Supply Voltage ...........................................+3.15V to +3.45V Ground Voltage ................................................................. 0V Power Dissipation .................................................... 235 mW FOSC (Oscillator or Crystal Frequency) ... 24 MHz ± 100 ppm Static Discharge Voltage .......................................... > 2000V 9.0 .................................................................. Parallel Resonant DC Characteristics Table 9-1. DC Characteristics Parameter VCC Description Conditions Supply Voltage VCC Ramp Up 0 to 3.3V Min. Typ. Max. Unit 3.15 3.3 3.45 V Input HIGH Voltage 2 VIL Input LOW Voltage VIH_X Crystal input HIGH Voltage VIL_X Crystal input LOW Voltage II Input Leakage Current 0< VIN < VCC VOH Output Voltage HIGH IOUT = 4 mA Output LOW Voltage IOUT = –4 mA IOH IOL CIN Input Pin Capacitance V –0.5 0.8 V 2 5.25 V 0.8 V ±10 µA 2.4 V 0.4 V Output Current HIGH 4 mA Output Current LOW 4 mA Suspend Current CY7C64714 Suspend Current CY7C64713 Except D+/D– 3.29 10 pF D+/D– 12.96 15 pF Connected 300 380[13] µA Disconnected 100 150[13] µA Connected .5 1.2 mA Disconnected .3 1.0 mA 35 65 mA ICC Supply Current 8051 running, connected to USB TRESET Reset Time after Valid Power VCC min = 3.0V Pin Reset after powered on 9.1 5.25 –0.05 VOL ISUSP µs 200 VIH 5.0 ms 200 µs USB Transceiver USB 2.0-compliant in full-speed mode. Note: 12. It is recommended to not power I/O when chip power is off. 13. Measured at Max VCC, 25ºC. Document #: 38-08039 Rev. *B Page 30 of 50 CY7C64713/14 10.0 AC Electrical Characteristics 10.1 USB Transceiver USB 2.0-compliant in full-speed mode. 10.2 Program Memory Read tCL CLKOUT[14] tAV tAV A[15..0] tSTBH tSTBL PSEN# [15] tACC1 D[7..0] tDH data in tSOEL OE# tSCSL CS# Figure 10-1. Program Memory Read Timing Diagram Table 10-1. Program Memory Read Parameters Parameter tCL Description Min. 1/CLKOUT Frequency Typ. Max. Unit Notes 20.83 ns 48 MHz 41.66 ns 24 MHz ns 12 MHz 83.2 tAV Delay from Clock to Valid Address 0 10.7 ns tSTBL Clock to PSEN Low 0 8 ns tSTBH Clock to PSEN High 0 8 ns tSOEL Clock to OE Low 11.1 ns tSCSL Clock to CS Low 13 ns tDSU Data Setup to Clock tDH Data Hold Time 9.6 ns 0 ns Notes: 14. CLKOUT is shown with positive polarity. 15. tACC1 is computed from the above parameters as follows: tACC1(24 MHz) = 3*tCL – tAV –tDSU = 106 ns tACC1(48 MHz) = 3*tCL – tAV – tDSU = 43 ns. Document #: 38-08039 Rev. *B Page 31 of 50 CY7C64713/14 10.3 Data Memory Read tCL Stretch = 0 CLKOUT[14] tAV tAV A[15..0] tSTBH tSTBL RD# tSCSL CS# tSOEL OE# tDSU [16 tDH tACC1 D[7..0] data in Stretch = 1 tCL CLKOUT[14] tAV A[15..0] RD# CS# tDSU [16] tACC1 D[7..0] tDH data in Figure 10-2. Data Memory Read Timing Diagram Table 10-2. Data Memory Read Parameters Parameter Description Min. 1/CLKOUT Frequency tCL Typ. Max. Unit Notes 20.83 ns 48 MHz 41.66 ns 24 MHz ns 12 MHz 83.2 tAV Delay from Clock to Valid Address 10.7 ns tSTBL Clock to RD LOW 11 ns tSTBH Clock to RD HIGH 11 ns tSCSL Clock to CS LOW 13 ns tSOEL Clock to OE LOW 11.1 ns tDSU Data Setup to Clock tDH Data Hold Time 9.6 ns 0 ns Note: 16. tACC2 and tACC3 are computed from the above parameters as follows: tACC2(24 MHz) = 3*tCL – tAV –tDSU = 106 ns tACC2(48 MHz) = 3*tCL – tAV – tDSU = 43 ns tACC3(24 MHz) = 5*tCL – tAV –tDSU = 190 ns tACC3(48 MHz) = 5*tCL – tAV – tDSU = 86 ns. Document #: 38-08039 Rev. *B Page 32 of 50 CY7C64713/14 10.4 Data Memory Write tCL CLKOUT tAV tSTBL tSTBH tAV A[15..0] WR# tSCSL CS# tON1 tOFF1 data out D[7..0] Stretch = 1 tCL CLKOUT tAV A[15..0] WR# CS# tON1 tOFF1 data out D[7..0] Figure 10-3. Data Memory Write Timing Diagram Table 10-3. Data Memory Write Parameters Parameter Description Min. Max. Unit 0 10.7 ns tAV Delay from Clock to Valid Address tSTBL Clock to WR Pulse LOW 0 11.2 ns tSTBH Clock to WR Pulse HIGH 0 11.2 ns tSCSL Clock to CS Pulse LOW 13.0 ns tON1 Clock to Data Turn-on 0 13.1 ns tOFF1 Clock to Data Hold Time 0 13.1 ns Document #: 38-08039 Rev. *B Notes Page 33 of 50 CY7C64713/14 10.5 GPIF Synchronous Signals tIFCLK IFCLK tSGA GPIFADR[8:0] RDYX tSRY tRYH DATA(input) valid tSGD tDAH CTLX tXCTL DATA(output) N N+1 tXGD Figure 10-4. GPIF Synchronous Signals Timing Diagram[17] Table 10-4. GPIF Synchronous Signals Parameters with Internally Sourced IFCLK[18, 19] Parameter Description tIFCLK IFCLK Period Min. Max. Unit 20.83 ns 8.9 ns 0 ns tSRY RDYX to Clock Setup Time tRYH Clock to RDYX tSGD GPIF Data to Clock Setup Time tDAH GPIF Data Hold Time tSGA Clock to GPIF Address Propagation Delay 7.5 ns tXGD Clock to GPIF Data Output Propagation Delay 11 ns tXCTL Clock to CTLX Output Propagation Delay 6.7 ns Min. Max. Unit 20.83 200 9.2 ns 0 ns Table 10-5. GPIF Synchronous Signals Parameters with Externally Sourced IFCLK[19] Parameter Description tIFCLK IFCLK Period tSRY RDYX to Clock Setup Time 2.9 ns tRYH Clock to RDYX 3.7 ns tSGD GPIF Data to Clock Setup Time 3.2 ns tDAH GPIF Data Hold Time 4.5 tSGA Clock to GPIF Address Propagation Delay tXGD Clock to GPIF Data Output Propagation Delay tXCTL Clock to CTLX Output Propagation Delay ns ns 11.5 ns 15 ns 10.7 ns Notes: 17. Dashed lines denote signals with programmable polarity. 18. GPIF asynchronous RDYx signals have a minimum Setup time of 50 ns when using internal 48-MHz IFCLK. 19. IFCLK must not exceed 48 MHz. Document #: 38-08039 Rev. *B Page 34 of 50 CY7C64713/14 10.6 Slave FIFO Synchronous Read tIFCLK IFCLK tSRD tRDH SLRD tXFLG FLAGS DATA N tOEon N+1 tXFD tOEoff SLOE Figure 10-5. Slave FIFO Synchronous Read Timing Diagram[17] Table 10-6. Slave FIFO Synchronous Read Parameters with Internally Sourced IFCLK[19] Parameter Description Min. Max. Unit tIFCLK IFCLK Period 20.83 ns tSRD SLRD to Clock Setup Time 18.7 ns tRDH Clock to SLRD Hold Time 0 tOEon SLOE Turn-on to FIFO Data Valid 10.5 tOEoff SLOE Turn-off to FIFO Data Hold 10.5 ns tXFLG Clock to FLAGS Output Propagation Delay 9.5 ns tXFD Clock to FIFO Data Output Propagation Delay 11 ns Min. Max. Unit 200 ns TBD ns ns Table 10-7. Slave FIFO Synchronous Read Parameters with Externally Sourced IFCLK[19] Parameter Description tIFCLK IFCLK Period 20.83 tSRD SLRD to Clock Setup Time 12.7 tRDH Clock to SLRD Hold Time 3.7 tOEon SLOE Turn-on to FIFO Data Valid tOEoff SLOE Turn-off to FIFO Data Hold 10.5 ns tXFLG Clock to FLAGS Output Propagation Delay 13.5 ns tXFD Clock to FIFO Data Output Propagation Delay 15 ns Document #: 38-08039 Rev. *B ns ns 10.5 TBD ns Page 35 of 50 CY7C64713/14 10.7 Slave FIFO Asynchronous Read tRDpwh SLRD tRDpwl tXFLG tXFD FLAGS DATA N N+1 tOEon tOEoff SLOE Figure 10-6. Slave FIFO Asynchronous Read Timing Diagram[17] Table 10-8. Slave FIFO Asynchronous Read Parameters[20] Parameter Description Min. Max. Unit tRDpwl SLRD Pulse Width LOW 50 tRDpwh SLRD Pulse Width HIGH 50 tXFLG SLRD to FLAGS Output Propagation Delay tXFD SLRD to FIFO Data Output Propagation Delay tOEon SLOE Turn-on to FIFO Data Valid tOEoff SLOE Turn-off to FIFO Data Hold 10.5 ns Document #: 38-08039 Rev. *B ns ns 70 ns 15 ns 10.5 ns Page 36 of 50 CY7C64713/14 10.8 Slave FIFO Synchronous Write tIFCLK IFCLK SLWR DATA tSWR tWRH N Z tSFD Z tFDH FLAGS tXFLG Figure 10-7. Slave FIFO Synchronous Write Timing Diagram[17] Table 10-9. Slave FIFO Synchronous Write Parameters with Internally Sourced IFCLK [19] Parameter Description Min. Max. Unit tIFCLK IFCLK Period 20.83 ns tSWR SLWR to Clock Setup Time 18.1 ns tWRH Clock to SLWR Hold Time 0 ns tSFD FIFO Data to Clock Setup Time 9.2 ns tFDH Clock to FIFO Data Hold Time 0 tXFLG Clock to FLAGS Output Propagation Time ns 9.5 ns Table 10-10. Slave FIFO Synchronous Write Parameters with Externally Sourced IFCLK [19] Min. Max. Unit tIFCLK Parameter IFCLK Period Description 20.83 200 ns tSWR SLWR to Clock Setup Time 12.1 ns tWRH Clock to SLWR Hold Time 3.6 ns tSFD FIFO Data to Clock Setup Time 3.2 ns tFDH Clock to FIFO Data Hold Time 4.5 ns Clock to FLAGS Output Propagation Time tXFLG Note: 20. Slave FIFO asynchronous parameter values use internal IFCLK setting at 48 MHz. Document #: 38-08039 Rev. *B 13.5 ns Page 37 of 50 CY7C64713/14 10.9 Slave FIFO Asynchronous Write tWRpwh SLWR/SLCS# tWRpwl tSFD tFDH DATA tXFD FLAGS Figure 10-8. Slave FIFO Asynchronous Write Timing Diagram[17] Table 10-11. Slave FIFO Asynchronous Write Parameters with Internally Sourced IFCLK [20] Parameter Description Min. Max. Unit tWRpwl SLWR Pulse LOW 50 ns tWRpwh SLWR Pulse HIGH 70 ns tSFD SLWR to FIFO DATA Setup Time 10 ns tFDH FIFO DATA to SLWR Hold Time 10 ns tXFD SLWR to FLAGS Output Propagation Delay 10.10 70 ns Slave FIFO Synchronous Packet End Strobe IFCLK tPEH PKTEND tSPE FLAGS tXFLG Figure 10-9. Slave FIFO Synchronous Packet End Strobe Timing Diagram[17] Table 10-12. Slave FIFO Synchronous Packet End Strobe Parameters with Internally Sourced IFCLK [19] Parameter Description Min. Max. Unit tIFCLK IFCLK Period 20.83 ns tSPE PKTEND to Clock Setup Time 14.6 ns tPEH Clock to PKTEND Hold Time 0 tXFLG Clock to FLAGS Output Propagation Delay ns 9.5 ns Table 10-13. Slave FIFO Synchronous Packet End Strobe Parameters with Externally Sourced IFCLK [19] Parameter Description Min. Max. Unit 20.83 200 ns tIFCLK IFCLK Period tSPE PKTEND to Clock Setup Time 8.6 tPEH Clock to PKTEND Hold Time 2.5 tXFLG Clock to FLAGS Output Propagation Delay There is no specific timing requirement that needs to be met for asserting PKTEND pin with regards to asserting SLWR. PKTEND can be asserted with the last data value clocked into Document #: 38-08039 Rev. *B ns ns 13.5 ns the FIFOs or thereafter. The only consideration is that the setup time tSPE and the hold time tPEH for PKTEND must be met. Although typically there are no specific timing requirements for asserting PKTEND in relation to SLWR, there exists a specific Page 38 of 50 CY7C64713/14 corner case condition that needs attention. While using the PKTEND to commit a one byte/word packet, an additional timing requirement needs to be met when the FIFO is configured to operate in auto mode and it is desired to send two packets back to back: • A full packet (full defined as the number of bytes in the FIFO meeting the level set in AUTOINLEN register) committed automatically followed by • A short one byte/word packet committed manually using the PKTEND pin. scenario. X is the value the AUTOINLEN register is set to when the IN endpoint is configured to be in auto mode. Figure 10-10 shows a scenario where two packets are being committed. The first packet gets comitted automatically when the number of bytes in the FIFO reaches X (value set in AUTOINLEN register) and the second one byte/word short packet being committed manually using PKTEND. Note that there is atleast one IFCLK cycle timing between asserting PKTEND and clocking of the last byte of the previous packet (causing the packet to be committed automatically). Failing to adhere to this timing, will result in the FX2 failing to send the one byte/word short packet. In this particular scenario, the developer must make sure to assert PKTEND at least one clock cycle after the rising edge that caused the last byte/word to be clocked into the previous auto committed packet. Figure 10-10 below shows this tIFCLK IFCLK tSFA tFAH FIFOADR >= tWRH >= tSWR SLWR tFDH tSFD X-4 DATA tSFD tFDH X-3 tFDH tSFD X-2 tFDH tSFD X-1 tSFD X tFDH tSFD tFDH 1 Atleast one IFCLK cycle tSPE tPEH PKTEND Figure 10-10. Slave FIFO Synchronous Write Sequence and Timing Diagram 10.11 Slave FIFO Asynchronous Packet End Strobe tPEpwh PKTEND tPEpwl FLAGS tXFLG Figure 10-11. Slave FIFO Asynchronous Packet End Strobe Timing Diagram[17] Table 10-14. Slave FIFO Asynchronous Packet End Strobe Parameters[20] Parameter Description Min. Max. Unit tPEpwl PKTEND Pulse Width LOW 50 ns tPWpwh PKTEND Pulse Width HIGH 50 ns tXFLG PKTEND to FLAGS Output Propagation Delay Document #: 38-08039 Rev. *B 115 ns Page 39 of 50 CY7C64713/14 10.12 Slave FIFO Output Enable SLOE tOEon DATA tOEoff Figure 10-12. Slave FIFO Output Enable Timing Diagram[17] Table 10-15. Slave FIFO Output Enable Parameters Parameter Description Min. Max. Unit tOEon SLOE Assert to FIFO DATA Output 10.5 ns tOEoff SLOE Deassert to FIFO DATA Hold 10.5 ns 10.13 Slave FIFO Address to Flags/Data FIFOADR [1.0] tXFLG FLAGS tXFD DATA N N+1 Figure 10-13. Slave FIFO Address to Flags/Data Timing Diagram[17] Table 10-16. Slave FIFO Address to Flags/Data Parameters Parameter Description Min. Max. Unit tXFLG FIFOADR[1:0] to FLAGS Output Propagation Delay 10.7 ns tXFD FIFOADR[1:0] to FIFODATA Output Propagation Delay 14.3 ns Document #: 38-08039 Rev. *B Page 40 of 50 CY7C64713/14 10.14 Slave FIFO Synchronous Address IFCLK SLCS/FIFOADR [1:0] tSFA tFAH Figure 10-14. Slave FIFO Synchronous Address Timing Diagram Table 10-17. Slave FIFO Synchronous Address Parameters [19] Parameter Description Min. Max. Unit 20.83 200 ns tIFCLK Interface Clock Period tSFA FIFOADR[1:0] to Clock Setup Time 25 ns tFAH Clock to FIFOADR[1:0] Hold Time 10 ns 10.15 Slave FIFO Asynchronous Address SLCS/FIFOADR [1:0] tSFA tFAH RD/WR/PKTEND Figure 10-15. Slave FIFO Asynchronous Address Timing Diagram[17] Table 10-18. Slave FIFO Asynchronous Address Parameters[20] Parameter Description Min. Max. Unit tSFA FIFOADR[1:0] to RD/WR/PKTEND Setup Time 10 ns tFAH RD/WR/PKTEND to FIFOADR[1:0] Hold Time 10 ns Document #: 38-08039 Rev. *B Page 41 of 50 CY7C64713/14 10.16 Sequence Diagram 10.16.1 Single and Burst Synchronous Read Example tIFCLK IFCLK tSFA tSFA tFAH tFAH FIFOADR t=0 tSRD T=0 tRDH >= tSRD >= tRDH SLRD t=3 t=2 T=3 T=2 SLCS tXFLG FLAGS tXFD tXFD Data Driven: N DATA N+1 N+1 N+2 N+4 N+3 tOEon tOEoff tOEon tXFD tXFD tOEoff SLOE t=4 t=1 T=4 T=1 Figure 10-16. Slave FIFO Synchronous Read Sequence and Timing Diagram IFCLK FIFO POINTER N IFCLK IFCLK N N+1 SLOE FIFO DATA BUS Not Driven N+1 IFCLK N+1 SLOE SLRD SLRD Driven: N IFCLK N+1 SLOE Not Driven IFCLK N+2 IFCLK N+3 SLRD N+1 IFCLK N+4 IFCLK SLRD N+2 N+3 N+4 IFCLK N+4 N+4 SLOE N+4 Not Driven Figure 10-17. Slave FIFO Synchronous Sequence of Events Diagram Figure 10-16 shows the timing relationship of the SLAVE FIFO signals during a synchronous FIFO read using IFCLK as the synchronizing clock. The diagram illustrates a single read followed by a burst read. • At t = 0 the FIFO address is stable and the signal SLCS is asserted (SLCS may be tied low in some applications). Note: tSFA has a minimum of 25 nsec. This means when IFCLK is running at 48 MHz, the FIFO address setup time is more than one IFCLK cycle. • At = 1, SLOE is asserted. SLOE is an output enable only, whose sole function is to drive the data bus. The data that is driven on the bus is the data that the internal FIFO pointer is currently pointing to. In this example it is the first data value in the FIFO. Note: the data is pre-fetched and is driven on the bus when SLOE is asserted. • At t = 2, SLRD is asserted. SLRD must meet the setup time of tSRD (time from asserting the SLRD signal to the rising edge of the IFCLK) and maintain a minimum hold time of tRDH (time from the IFCLK edge to the de-assertion of the SLRD signal). If the SLCS signal is used, it must be asserted Document #: 38-08039 Rev. *B with SLRD, or before SLRD is asserted (i.e. the SLCS and SLRD signals must both be asserted to start a valid read condition). • The FIFO pointer is updated on the rising edge of the IFCLK, while SLRD is asserted. This starts the propagation of data from the newly addressed location to the data bus. After a propagation delay of tXFD (measured from the rising edge of IFCLK) the new data value is present. N is the first data value read from the FIFO. In order to have data on the FIFO data bus, SLOE MUST also be asserted. The same sequence of events are shown for a burst read and are marked with the time indicators of T=0 through 5. Note: For the burst mode, the SLRD and SLOE are left asserted during the entire duration of the read. In the burst read mode, when SLOE is asserted, data indexed by the FIFO pointer is on the data bus. During the first read cycle, on the rising edge of the clock the FIFO pointer is updated and increments to point to address N+1. For each subsequent rising edge of IFCLK, while the SLRD is asserted, the FIFO pointer is incremented and the next data value is placed on the data bus. Page 42 of 50 CY7C64713/14 10.16.2 Single and Burst Synchronous Write tIFCLK IFCLK tSFA tSFA tFAH tFAH FIFOADR t=0 tSWR tWRH >= tWRH >= tSWR T=0 SLWR t=2 T=2 t=3 T=5 SLCS tXFLG tXFLG FLAGS tFDH tSFD tSFD N+1 N DATA t=1 tFDH T=1 tSFD tSFD tFDH N+3 N+2 T=3 tFDH T=4 tSPE tPEH PKTEND Figure 10-18. Slave FIFO Synchronous Write Sequence and Timing Diagram[17] The Figure 10-18 shows the timing relationship of the SLAVE FIFO signals during a synchronous write using IFCLK as the synchronizing clock. The diagram illustrates a single write followed by burst write of 3 bytes and committing all 4 bytes as a short packet using the PKTEND pin. • At t = 0 the FIFO address is stable and the signal SLCS is asserted. (SLCS may be tied low in some applications) Note: tSFA has a minimum of 25 ns. This means when IFCLK is running at 48 MHz, the FIFO address setup time is more than one IFCLK cycle. • At t = 1, the external master/peripheral must outputs the data value onto the data bus with a minimum set up time of tSFD before the rising edge of IFCLK. • At t = 2, SLWR is asserted. The SLWR must meet the setup time of tSWR (time from asserting the SLWR signal to the rising edge of IFCLK) and maintain a minimum hold time of tWRH (time from the IFCLK edge to the de-assertion of the SLWR signal). If SLCS signal is used, it must be asserted with SLWR or before SLWR is asserted. (i.e. the SLCS and SLWR signals must both be asserted to start a valid write condition). • While the SLWR is asserted, data is written to the FIFO and on the rising edge of the IFCLK, the FIFO pointer is incremented. The FIFO flag will also be updated after a delay of tXFLG from the rising edge of the clock. The same sequence of events are also shown for a burst write and are marked with the time indicators of T=0 through 5. Note: For the burst mode, SLWR and SLCS are left asserted for the entire duration of writing all the required data values. In this burst write mode, once the SLWR is asserted, the data on the FIFO data bus is written to the FIFO on every rising edge Document #: 38-08039 Rev. *B of IFCLK. The FIFO pointer is updated on each rising edge of IFCLK. In Figure 10-18, once the four bytes are written to the FIFO, SLWR is de-asserted. The short 4-byte packet can be committed to the host by asserting the PKTEND signal. There is no specific timing requirement that needs to be met for asserting PKTEND signal with regards to asserting the SLWR signal. PKTEND can be asserted with the last data value or thereafter. The only consideration is the setup time tSPE and the hold time tPEH must be met. In the scenario of Figure 10-18, the number of data values committed includes the last value written to the FIFO. In this example, both the data value and the PKTEND signal are clocked on the same rising edge of IFCLK. PKTEND can be asserted in subsequent clock cycles. The FIFOADDR lines should be held constant during the PKTEND assertion. Although there are no specific timing requirement for asserting PKTEND, there is a specific corner case condition that needs attention while using the PKTEND to commit a one byte/word packet. Additional timing requirements exists when the FIFO is configured to operate in auto mode and it is desired to send two packets: a full packet (full defined as the number of bytes in the FIFO meeting the level set in AUTOINLEN register) committed automatically followed by a short one byte/word packet committed manually using the PKTEND pin. In this case, the external master must make sure to assert the PKTEND pin atleast one clock cycle after the rising edge that caused the last byte/word to be clocked into the previous auto committed packet ( the packet with the number of bytes equal to what is set in the AUTOINLEN register). Refer to section 1010 for further details on this timing. Page 43 of 50 CY7C64713/14 10.16.3 Sequence Diagram of a Single and Burst Asynchronous Read tSFA tFAH tSFA tFAH FIFOADR t=0 tRDpwl tRDpwh tRDpwl T=0 tRDpwl tRDpwh tRDpwl tRDpwh tRDpwh SLRD t=2 t=3 T=2 T=3 T=5 T=4 T=6 SLCS tXFLG tXFLG FLAGS tXFD Data (X) Driven DATA tXFD tXFD N N N+3 N+2 tOEon tOEoff tOEon tXFD N+1 tOEoff SLOE t=4 t=1 T=1 T=7 Figure 10-19. Slave FIFO Asynchronous Read Sequence and Timing Diagram SLOE FIFO POINTER SLRD FIFO DATA BUS Not Driven SLRD SLOE SLOE SLRD SLRD SLRD SLRD SLOE N N N+1 N+1 N+1 N+1 N+2 N+2 N+3 N+3 Driven: X N N Not Driven N N+1 N+1 N+2 N+2 Not Driven N Figure 10-20. Slave FIFO Asynchronous Read Sequence of Events Diagram Figure 10-19 diagrams the timing relationship of the SLAVE FIFO signals during an asynchronous FIFO read. It shows a single read followed by a burst read. • At t = 0 the FIFO address is stable and the SLCS signal is asserted. • At t = 1, SLOE is asserted. This results in the data bus being driven. The data that is driven on to the bus is previous data, it data that was in the FIFO from a prior read cycle. • At t = 2, SLRD is asserted. The SLRD must meet the minimum active pulse of tRDpwl and minimum de-active pulse width of tRDpwh. If SLCS is used then, SLCS must be in asserted with SLRD or before SLRD is asserted. (i.e. the SLCS and SLRD signals must both be asserted to start a valid read condition.) Document #: 38-08039 Rev. *B • The data that will be driven, after asserting SLRD, is the updated data from the FIFO. This data is valid after a propagation delay of tXFD from the activating edge of SLRD. In Figure 10-19, data N is the first valid data read from the FIFO. For data to appear on the data bus during the read cycle (i.e. SLRD is asserted), SLOE MUST be in an asserted state. SLRD and SLOE can also be tied together. The same sequence of events is also shown for a burst read marked with T = 0 through 5. Note: In burst read mode, during SLOE is assertion, the data bus is in a driven state and outputs the previous data. Once SLRD is asserted, the data from the FIFO is driven on the data bus (SLOE must also be asserted) and then the FIFO pointer is incremented. Page 44 of 50 CY7C64713/14 10.16.4 Sequence Diagram of a Single and Burst Asynchronous Write tSFA tSFA tFAH tFAH FIFOADR t=0 tWRpwl T=0 tWRpwh tWRpwl tWRpwl tWRpwh tWRpwl tWRpwh tWRpwh SLWR t=3 t =1 T=1 T=3 T=4 T=6 T=7 T=9 SLCS tXFLG tXFLG FLAGS tSFD tFDH tSFD tFDH tSFD tFDH tSFD tFDH N+1 N+2 N+3 N DATA t=2 T=2 T=5 T=8 tPEpwl tPEpwh PKTEND Figure 10-21. Slave FIFO Asynchronous Write Sequence and Timing Diagram[17] Figure 10-21 diagrams the timing relationship of the SLAVE FIFO write in an asynchronous mode. The diagram shows a single write followed by a burst write of 3 bytes and committing the 4-byte-short packet using PKTEND. ·At t = 0 the FIFO address is applied, insuring that it meets the setup time of tSFA. If SLCS is used, it must also be asserted (SLCS may be tied low in some applications). ·At t = 1 SLWR is asserted. SLWR must meet the minimum active pulse of tWRpwl and minimum de-active pulse width of tWRpwh. If the SLCS is used, it must be in asserted with SLWR or before SLWR is asserted. ·At t = 2, data must be present on the bus tSFD before the de-asserting edge of SLWR. ·At t = 3, deasserting SLWR will cause the data to be written from the data bus to the FIFO and then increments the FIFO pointer. The FIFO flag is also updated after tXFLG from the de-asserting edge of SLWR. The same sequence of events are shown for a burst write and is indicated by the timing marks of T = 0 through 5. Note: In the burst write mode, once SLWR is deasserted, the data is written to the FIFO and then the FIFO pointer is incremented to the next byte in the FIFO. The FIFO pointer is post incremented. In Figure 10-21 once the four bytes are written to the FIFO and SLWR is deasserted, the short 4-byte packet can be committed to the host using the PKTEND. The external device should be designed to not assert SLWR and the PKTEND signal at the same time. It should be designed to assert the PKTEND after SLWR is deasserted and met the minimum deasserted pulse width. The FIFOADDR lines are to be held constant during the PKTEND assertion. 11.0 Ordering Information Table 11-1. Ordering Information Ordering Code Package Type RAM Size # Prog I/Os 8051 Address /Data Busses 16K 40 16/8 bit Ideal for battery powered applications CY7C64714-128AXC 128 TQFP – Lead-Free CY7C64714-100AXC 100 TQFP – Lead-Free 16K 40 – CY7C64714-56LFXC 56 QFN – Lead-Free 16K 24 – 128 TQFP - Lead-Free 16K 40 16/8 bit CY7C64713-100AXC 100 TQFP - Lead-Free 16K 40 - CY7C64713-56LFXC 56 QFN - Lead-Free 16K 24 - CY3674 EZ-USB FX1 Development Kit Ideal for non-battery powered applications CY7C64713-128AXC Document #: 38-08039 Rev. *B Page 45 of 50 CY7C64713/14 12.0 Package Diagrams The FX1 is available in three packages: • 56-pin QFN • 100-pin TQFP • 128-pin TQFP Package Diagrams TOP VIEW BOTTOM VIEW SIDE VIEW 0.08[0.003] C 1.00[0.039] MAX. 7.90[0.311] 8.10[0.319] A 0.05[0.002] MAX. 0.80[0.031] MAX. 7.70[0.303] 7.80[0.307] 0.18[0.007] 0.28[0.011] 0.20[0.008] REF. 0.80[0.031] DIA. PIN1 ID 0.20[0.008] R. N N 1 1 2 2 0.45[0.018] 6.45[0.254] 6.55[0.258] 7.90[0.311] 8.10[0.319] 7.70[0.303] 7.80[0.307] E-PAD (PAD SIZE VARY BY DEVICE TYPE) 0.30[0.012] 0.50[0.020] 0°-12° 0.50[0.020] C SEATING PLANE 0.24[0.009] 0.60[0.024] (4X) 6.45[0.254] 6.55[0.258] 51-85144-*D Figure 12-1. 56-Lead QFN 8 x 8 mm LF56A Document #: 38-08039 Rev. *B Page 46 of 50 CY7C64713/14 Package Diagrams (continued) 51-85050-*A Figure 12-2. 100-Pin Thin Plastic Quad Flatpack (14 x 20 x 1.4 mm) A101 Document #: 38-08039 Rev. *B Page 47 of 50 CY7C64713/14 Package Diagrams (continued) Figure 12-3. 128-Lead Thin Plastic Quad Flatpack (14 x 20 x 1.4 mm) A128 13.0 Quad Flat Package No Leads (QFN) Package Design Notes Electrical contact of the part to the Printed Circuit Board (PCB) is made by soldering the leads on the bottom surface of the package to the PCB. Hence, special attention is required to the heat transfer area below the package to provide a good thermal bond to the circuit board. A Copper (Cu) fill is to be designed into the PCB as a thermal pad under the package. Heat is transferred from the FX1 through the device’s metal paddle on the bottom side of the package. Heat from here, is conducted to the PCB at the thermal pad. It is then conducted from the thermal pad to the PCB inner ground plane by a 5 x 5 array of via. A via is a plated through hole in the PCB with a finished diameter of 13 mil. The QFN’s metal die paddle must be soldered to the PCB’s thermal pad. Solder mask is placed on the board top side over each via to resist solder flow into the via. The mask on the top side also minimizes outgassing during the solder reflow process. Document #: 38-08039 Rev. *B 51-85101-*B For further information on this package design please refer to the application note Surface Mount Assembly of AMKOR’s MicroLeadFrame (MLF) Technology. This application note can be downloaded from AMKOR’s website from the following URL http://www.amkor.com/products/notes_papers/MLF_AppNote _0902.pdf. The application note provides detailed information on board mounting guidelines, soldering flow, rework process, etc. Figure 13-1 below displays a cross-sectional area underneath the package. The cross section is of only one via. The solder paste template needs to be designed to allow at least 50% solder coverage. The thickness of the solder paste template should be 5 mil. It is recommended that “No Clean” type 3 solder paste is used for mounting the part. Nitrogen purge is recommended during reflow. Page 48 of 50 CY7C64713/14 Figure 13-2 is a plot of the solder mask pattern and Figure 13-3 displays an X-Ray image of the assembly (darker areas indicate solder). 0.017” dia Solder Mask Cu Fill Cu Fill PCB Material Via hole for thermally connecting the QFN to the circuit board ground plane. 0.013” dia PCB Material This figure only shows the top three layers of the circuit board: Top Solder, PCB Dielectric, and the Ground Plane Figure 13-1. Cross-section of the Area Underneath the QFN Package Figure 13-2. Plot of the Solder Mask (White Area) Figure 13-3. X-ray Image of the Assembly Purchase of I2C components from Cypress, or one of its sublicensed Associated Companies, conveys a license under the Philips 2C Patent Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification I as defined by Philips. EZ-USB FX1, EZ-USB FX2LP, EZ-USB FX2, and ReNumeration are trademarks, and EZ-USB is a registered trademark, of Cypress Semiconductor. All product and company names mentioned in this document are the trademarks of their respective holders. Document #: 38-08039 Rev. *B Page 49 of 50 © Cypress Semiconductor Corporation, 2005. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress CY7C64713/14 Document History Page Document Title: CY7C64713/4 EZ-USB FX1™ USB Microcontroller Full-Speed USB Peripheral Controller Document Number: 38-08039 REV. ECN NO. Issue Date Orig. of Change Description of Change ** 132091 02/10/04 KKU New Data Sheet *A 230709 SEE ECN KKU Changed Lead free Marketing part numbers in Table 11-1 according to spec change in 28-00054. *B 307474 SEE ECN BHA Changed default PID in Table 4-2. Updated register table. Removed word compatible where associated with I2C. Changed Set-up to Setup. Added Power Dissipation. Changed Vcc from ± 10% to ± 5% Added values for VIH_X, VIL_X Added values for ICC Added values for ISUSP Removed IUNCONFIGURED from table 9-1 Changed PKTEND to FLAGS output propagation delay (asynchronous interface) in Table 10-14 from a maximum value of 70 ns to 115 ns. Removed 56 SSOP and added 56 QFN package Provided additional timing restrictions and requirement regarding the use of PKTEND pin to commit a short one byte/word packet subsequent to committing a packet automatically (when in auto mode). Added part number CY7C64714 ideal for battery powered applications. Changed Supply Voltage in section 8 to read +3.15V to +3.45V Added Min Vcc Ramp Up time (0 to 3.3v) Removed Preliminary Document #: 38-08039 Rev. *B Page 50 of 50 © Cypress Semiconductor Corporation, 2005. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress