CY7C64713 EZ-USB FX1™ USB Microcontroller Full Speed USB Peripheral Controller EZ-USB FX1™ USB Microcontroller Full Speed USB Peripheral Controller Features ■ ■ ■ Integrated, industry standard 8051 with enhanced features: Single chip integrated USB transceiver, SIE, and enhanced 8051 microprocessor ❐ Up to 48 MHz clock rate ❐ Four clocks for each instruction cycle Fit, form, and function upgradable to the FX2LP (CY7C68013A) ❐ Two USARTS ❐ Pin compatible ❐ Three counters or timers ❐ Object code compatible ❐ Expanded interrupt system Functionally compatible (FX1 functionality is a subset of the FX2LP) ❐ Two data pointers ❐ ■ Draws no more than 65 mA in any mode, making the FX1 suitable for bus powered applications ■ Software: 8051 runs from internal RAM, which is: ❐ Downloaded using USB ❐ Loaded from EEPROM ❐ External memory device (128 pin configuration only) ■ 16 KB of on-chip code/data RAM ■ Four programmable endpoints ❐ BULK/INTERRUPT/ISOCHRONOUS 3.3 V operation with 5 V tolerant inputs ■ Smart SIE ■ Vectored USB interrupts ■ Separate data buffers for the setup and DATA portions of a CONTROL transfer ■ Integrated I2C controller, running at 100 or 400 KHz ■ 48 MHz, 24 MHz, or 12 MHz 8051 operation ■ Four integrated FIFOs Buffering options: double, triple, and quad ■ Additional endpoint ■ 8- or 16-bit external data interface ■ Smart media standard ECC generation ■ GPIF programmable (BULK/INTERRUPT) 64-byte ❐ Allows direct connection to most parallel interfaces; 8- and 16-bit ❐ Programmable waveform descriptors and configuration registers to define waveforms ❐ ■ • Brings glue and FIFOs inside for lower system cost ❐ Automatic conversion to and from 16-bit buses ❐ Master or slave operation ❐ FIFOs can use externally supplied clock or asynchronous strobes ❐ Easy interface to ASIC and DSP ICs ■ Vectored for FIFO and GPIF Interrupts ■ Up to 40 general purpose IOs (GPIO) ■ Four package options: Supports multiple ready (RDY) inputs and Control (CTL) outputs Cypress Semiconductor Corporation Document Number: 38-08039 Rev. *J ❐ 198 Champion Court ❐ 128-pin TQFP ❐ 100-pin TQFP ❐ 56-pin SSOP ❐ 56-pin QFN Pb-free • San Jose, CA 95134-1709 • 408-943-2600 Revised May 17, 2011 [+] Feedback CY7C64713 Logic Block Diagram High performance micro using standard tools with lower-power options VCC x20 PLL /0.5 /1.0 /2.0 Data (8) Address (16) FX1 8051 Core 12/24/48 MHz, four clocks/cycle 1.5k connected for enumeration D+ USB D– XCVR CY Smart 16 KB RAM Address (16) / Data Bus (8) 24 MHz Ext. XTAL I2C Master Abundant I/O including two USARTS Additional IOs (24) ADDR (9) GPIF RDY (6) CTL (6) ECC USB Engine Integrated full speed XCVR 4 kB FIFO Enhanced USB core Simplifies 8051 code Document Number: 38-08039 Rev. *J ‘Soft Configuration’ Easy firmware changes 8/16 General programmable I/F to ASIC/DSP or bus standards such as ATAPI, EPP, etc. Up to 96 MBytes burst rate FIFO and endpoint memory (master or slave operation) Page 2 of 72 [+] Feedback CY7C64713 Contents Functional Description ..................................................... 4 Applications ...................................................................... 4 Functional Overview ........................................................ 4 USB Signaling Speed .................................................. 4 8051 Microprocessor ................................................... 4 I2C Bus ........................................................................ 5 Buses .......................................................................... 5 USB Boot Methods ...................................................... 5 ReNumeration™ .......................................................... 6 Bus-powered Applications ........................................... 6 Interrupt System .......................................................... 6 Reset and Wakeup ...................................................... 8 Program/Data RAM ..................................................... 9 Endpoint RAM ........................................................... 11 External FIFO Interface ............................................. 11 GPIF .......................................................................... 12 ECC Generation ........................................................ 13 USB Uploads and Downloads ................................... 13 Autopointer Access ................................................... 13 I2C Controller ............................................................. 13 Compatible with Previous Generation EZ-USB FX2 . 14 Pin Assignments ............................................................ 14 CY7C64713 Pin Definitions ............................................ 20 Register Summary .......................................................... 28 Absolute Maximum Ratings .......................................... 47 Operating Conditions ..................................................... 47 DC Characteristics ......................................................... 47 USB Transceiver ....................................................... 47 Document Number: 38-08039 Rev. *J AC Electrical Characteristics ........................................ 48 USB Transceiver ....................................................... 48 PORTC Strobe Feature Timings ............................... 51 GPIF Synchronous Signals ....................................... 52 Slave FIFO Synchronous Read ................................. 53 Slave FIFO Asynchronous Read ............................... 54 Slave FIFO Synchronous Write ................................. 55 Slave FIFO Asynchronous Write ............................... 56 Slave FIFO Synchronous Packet End Strobe ........... 56 Slave FIFO Asynchronous Packet End Strobe ......... 58 Slave FIFO Output Enable ........................................ 58 Slave FIFO Address to Flags/Data ............................ 58 Slave FIFO Synchronous Address ............................ 59 Slave FIFO Asynchronous Address .......................... 59 Sequence Diagram .................................................... 60 Ordering Information ...................................................... 64 Ordering Code Definitions ......................................... 64 Package Diagrams .......................................................... 65 Quad Flat Package No Leads (QFN) Package Design Notes ................................................................... 68 Acronyms ........................................................................ 70 Document Conventions ................................................. 70 Units of Measure ....................................................... 70 Document History Page ................................................. 71 Sales, Solutions, and Legal Information ...................... 72 Worldwide Sales and Design Support ....................... 72 Products .................................................................... 72 PSoC Solutions ......................................................... 72 Page 3 of 72 [+] Feedback CY7C64713 Functional Description EZ-USB FX1 (CY7C64713) is a full speed, highly integrated, USB microcontroller. By integrating the USB transceiver, Serial Interface Engine (SIE), enhanced 8051 microcontroller, and a programmable peripheral interface in a single chip, Cypress has created a very cost effective solution that provides superior time-to-market advantages. FX1 does not support the low speed signaling mode of 1.5 Mbps or the high speed mode of 480 Mbps. 8051 Microprocessor The 8051 microprocessor embedded in the FX1 family has 256 bytes of register RAM, an expanded interrupt system, three timer/counters, and two USARTs. The EZ-USB FX1 is more economical, because it incorporates the USB transceiver and provides a smaller footprint solution than the USB SIE or external transceiver implementations. With EZ-USB FX1, the Cypress Smart SIE handles most of the USB protocol in hardware, freeing the embedded microcontroller for application specific functions and decreasing the development time to ensure USB compatibility. 8051 Clock Frequency The General Programmable Interface (GPIF) and Master/Slave Endpoint FIFO (8 or 16-bit data bus) provide an easy and glueless interface to popular interfaces such as ATA, UTOPIA, EPP, PCMCIA, and most DSP/processors. Four Pb-free packages are defined for the family: 56-pin SSOP, 56-pin QFN, 100-pin TQFP, and 128-pin TQFP. Applications ■ DSL modems ■ ATA interface ■ Memory card readers ■ Legacy conversion devices ■ Home PNA ■ Wireless LAN ■ MP3 players ■ Networking The Reference Designs section of the cypress website provides additional tools for typical USB applications. Each reference design comes complete with firmware source and object code, schematics, and documentation. Please visit http://www.cypress.com for more information. Functional Overview USB Signaling Speed FX1 operates at one of the three rates defined in the USB Specification Revision 2.0, dated April 27, 2000: Full speed, with a signaling bit rate of 12 Mbps. FX1 has an on-chip oscillator circuit that uses an external 24 MHz (±100 ppm) crystal with the following characteristics: ■ Parallel resonant ■ Fundamental mode ■ 500 W drive level ■ 12 pF (5% tolerance) load capacitors. An on-chip PLL multiplies the 24 MHz oscillator up to 480 MHz, as required by the transceiver/PHY, and the internal counters divide it down for use as the 8051 clock. The default 8051 clock frequency is 12 MHz. The clock frequency of the 8051 is dynamically changed by the 8051 through the CPUCS register. The CLKOUT pin, which is three-stated and inverted using the internal control bits, outputs the 50% duty cycle 8051 clock at the selected 8051 clock frequency which is 48, 24, or 12 MHz. USARTS FX1 contains two standard 8051 USARTs, addressed by Special Function Register (SFR) bits. The USART interface pins are available on separate I/O pins, and are not multiplexed with port pins. UART0 and UART1 can operate using an internal clock at 230 KBaud with no more than 1% baud rate error. 230 KBaud operation is achieved by an internally derived clock source that generates overflow pulses at the appropriate time. The internal clock adjusts for the 8051 clock rate (48, 24, 12 MHz) such that it always presents the correct frequency for 230-KBaud operation.[1] Special Function Registers Certain 8051 SFR addresses are populated to provide fast access to critical FX1 functions. These SFR additions are shown in Table 1 on page 5. Bold type indicates non-standard, enhanced 8051 registers. The two SFR rows that end with ‘0’ and ‘8’ contain bit addressable registers. The four I/O ports A–D use the SFR addresses used in the standard 8051 for ports 0–3, which are not implemented in the FX1. Because of the faster and more efficient SFR addressing, the FX1 I/O ports are not addressable in the external RAM space (using the MOVX instruction). Note 1. 115-KBaud operation is also possible by programming the 8051 SMOD0 or SMOD1 bits to a ‘1’ for UART0 and UART1, respectively. Document Number: 38-08039 Rev. *J Page 4 of 72 [+] Feedback CY7C64713 Figure 1. Crystal Configuration C1 24 MHz 12 pF C2 12 pF 12-pF capacitor values assumes a trace capacitance of 3 pF per side on a four layer FR4 PCA 20 × PLL Table 1. Special Function Registers x 8x 9x Ax Bx Cx Dx Ex Fx 0 IOA IOB IOC IOD SCON1 PSW ACC B SBUF1 EICON EIE EIP 1 SP EXIF INT2CLR IOE 2 DPL0 MPAGE INT4CLR OEA 3 DPH0 OEB 4 DPL1 OEC 5 DPH1 OED 6 DPS OEE 7 PCON 8 TCON 9 TMOD SBUF0 A TL0 AUTOPTRH1 B TL1 C TH0 D TH1 AUTOPTRH2 GPIFSGLDATH E CKCON AUTOPTRL2 GPIFSGLDATLX F SCON0 IE IP T2CON EP2468STAT EP01STAT RCAP2L AUTOPTRL1 EP24FIFOFLGS GPIFTRIG RCAP2H reserved EP68FIFOFLGS reserved AUTOPTRSETUP I2C Bus TL2 TH2 GPIFSGLDATLNOX FX1 supports the I2C bus as a master only at 100/400 KHz. SCL and SDA pins have open drain outputs and hysteresis inputs. These signals must be pulled up to 3.3 V, even if no I2C device is connected. in place of the internally stored values (0xC0). Alternatively, it boot-loads the EEPROM contents into an internal RAM (0xC2). If no EEPROM is detected, FX1 enumerates using internally stored descriptors. The default ID values for FX1 are VID/PID/DID (0x04B4, 0x6473, 0xAxxx where xxx=Chip revision).[2] Buses Table 2. Default ID Values for FX1 All packages: 8 or 16-bit ‘FIFO’ bidirectional data bus, multiplexed on I/O ports B and D. 128-pin package: adds 16-bit output only 8051 address bus, 8-bit bidirectional data bus. Vendor ID 0x04B4 Cypress Semiconductor USB Boot Methods Product ID 0x6473 EZ-USB FX1 During the power up sequence, internal logic checks the I2C port for the connection of an EEPROM whose first byte is either 0xC0 or 0xC2. If found, it uses the VID/PID/DID values in the EEPROM Device release Default VID/PID/DID 0xAnnn Depends on chip revision (nnn = chip revision where first silicon = 001) Notes 2. The I2C bus SCL and SDA pins must be pulled up, even if an EEPROM is not connected. Otherwise this detection method does not work properly. Document Number: 38-08039 Rev. *J Page 5 of 72 [+] Feedback CY7C64713 ReNumeration™ USB-Interrupt Autovectors Because the FX1’s configuration is soft, one chip can take on the identities of multiple distinct USB devices. The main USB interrupt is shared by 27 interrupt sources. The FX1 provides a second level of interrupt vectoring, called Autovectoring, to save code and processing time that is normally required to identify the individual USB interrupt source. When a USB interrupt is asserted, the FX1 pushes the program counter on to its stack and then jumps to address 0x0043, where it expects to find a “jump” instruction to the USB Interrupt service routine. When first plugged into the USB, the FX1 enumerates automatically and downloads firmware and the USB descriptor tables over the USB cable. Next, the FX1 enumerates again, this time as a device defined by the downloaded information. This patented two step process, called ReNumeration, happens instantly when the device is plugged in, with no indication that the initial download step has occurred. Two control bits in the USBCS (USB Control and Status) register control the ReNumeration process: DISCON and RENUM. To simulate a USB disconnect, the firmware sets DISCON to 1. To reconnect, the firmware clears DISCON to 0. Before reconnecting, the firmware sets or clears the RENUM bit to indicate if the firmware or the Default USB Device handles device requests over endpoint zero: ■ RENUM = 0, the Default USB Device handles device requests ■ RENUM = 1, the firmware handles device requests Bus-powered Applications The FX1 fully supports bus powered designs by enumerating with less than 100 mA as required by the USB specification. Interrupt System INT2 Interrupt Request and Enable Registers FX1 implements an autovector feature for INT2 and INT4. There are 27 INT2 (USB) vectors, and 14 INT4 (FIFO/GPIF) vectors. See EZ-USB Technical Reference Manual (TRM) for more details. The FX1 jump instruction is encoded as shown in Table 3. If Autovectoring is enabled (AV2EN = 1 in the INTSETUP register), the FX1 substitutes its INT2VEC byte. Therefore, if the high byte (“page”) of a jump table address is preloaded at location 0x0044, the automatically inserted INT2VEC byte at 0x0045 directs the jump to the correct address out of the 27 addresses within the page. FIFO/GPIF Interrupt (INT4) Just as the USB Interrupt is shared among 27 individual USB-interrupt sources, the FIFO/GPIF interrupt is shared among 14 individual FIFO/GPIF sources. The FIFO/GPIF Interrupt, such as the USB Interrupt, can employ autovectoring. Table 4 on page 7 shows the priority and INT4VEC values for the 14 FIFO/GPIF interrupt sources. FIFO/GPIF Interrupt (INT4) Just as the USB Interrupt is shared among 27 individual USB-interrupt sources, the FIFO/GPIF interrupt is shared among 14 individual FIFO/GPIF sources. The FIFO/GPIF Interrupt, such as the USB Interrupt, can employ autovectoring. Table 4 on page 7 shows the priority and INT4VEC values for the 14 FIFO/GPIF interrupt sources. Table 3. INT2 USB Interrupts USB INTERRUPT TABLE FOR INT2 Priority INT2VEC Value 1 00 SUDAV Source Notes 2 04 SOF Start of Frame 3 08 SUTOK Setup Token Received 4 0C SUSPEND USB Suspend request 5 10 USB RESET Bus reset 6 14 7 18 8 1C 9 Setup Data Available Reserved EP0ACK FX1 ACK’d the CONTROL Handshake 20 EP0-IN EP0-IN ready to be loaded with data 10 24 EP0-OUT EP0-OUT has USB data 11 28 EP1-IN EP1-IN ready to be loaded with data 12 2C EP1-OUT EP1-OUT has USB data 13 30 EP2 IN: buffer available. OUT: buffer has data 14 34 EP4 IN: buffer available. OUT: buffer has data 15 38 EP6 IN: buffer available. OUT: buffer has data 16 3C EP8 IN: buffer available. OUT: buffer has data 17 40 IBN IN-Bulk-NAK (any IN endpoint) Reserved Document Number: 38-08039 Rev. *J Page 6 of 72 [+] Feedback CY7C64713 Table 3. INT2 USB Interrupts (continued) USB INTERRUPT TABLE FOR INT2 Priority INT2VEC Value 18 44 Source Notes Reserved 19 48 EP0PING EP0 OUT was Pinged and it NAK’d 20 4C EP1PING EP1 OUT was Pinged and it NAK’d 21 50 EP2PING EP2 OUT was Pinged and it NAK’d 22 54 EP4PING EP4 OUT was Pinged and it NAK’d 23 58 EP6PING EP6 OUT was Pinged and it NAK’d 24 5C EP8PING EP8 OUT was Pinged and it NAK’d 25 60 ERRLIMIT Bus errors exceeded the programmed limit 26 64 27 68 Reserved 28 6C Reserved 29 70 EP2ISOERR ISO EP2 OUT PID sequence error 30 74 EP4ISOERR ISO EP4 OUT PID sequence error 31 78 EP6ISOERR ISO EP6 OUT PID sequence error 32 7C EP8ISOERR ISO EP8 OUT PID sequence error Table 4. Individual FIFO/GPIF Interrupt Sources Priority INT4VEC Value 1 80 Source EP2PF Notes Endpoint 2 Programmable Flag 2 84 EP4PF Endpoint 4 Programmable Flag 3 88 EP6PF Endpoint 6 Programmable Flag 4 8C EP8PF Endpoint 8 Programmable Flag 5 90 EP2EF Endpoint 2 Empty Flag 6 94 EP4EF Endpoint 4 Empty Flag 7 98 EP6EF Endpoint 6 Empty Flag 8 9C EP8EF Endpoint 8 Empty Flag 9 A0 EP2FF Endpoint 2 Full Flag 10 A4 EP4FF Endpoint 4 Full Flag 11 A8 EP6FF Endpoint 6 Full Flag 12 AC EP8FF Endpoint 8 Full Flag 13 B0 GPIFDONE GPIF Operation Complete 14 B4 GPIFWF GPIF Waveform If Autovectoring is enabled (AV4EN = 1 in the INTSETUP register), the FX1 substitutes its INT4VEC byte. Therefore, if the high byte (“page”) of a jump-table address is preloaded at location 0x0054, the automatically inserted INT4VEC byte at 0x0055 directs the jump to the correct address out of the 14 Document Number: 38-08039 Rev. *J addresses within the page. When the ISR occurs, the FX1 pushes the program counter onto its stack and then jumps to address 0x0053, where it expects to find a “jump” instruction to the ISR Interrupt service routine. Page 7 of 72 [+] Feedback CY7C64713 Reset and Wakeup Reset Pin The input pin, RESET#, resets the FX1 when asserted. This pin has hysteresis and is active LOW. When a crystal is used with the CY7C64713, the reset period must allow for the stabilization of the crystal and the PLL. This reset period must be approximately 5 ms after VCC has reached 3.0 Volts. If the crystal input pin is driven by a clock signal the internal PLL stabilizes in 200 s after VCC has reached 3.0 V[3]. Figure 2 on page 8 shows a power on reset condition and a reset applied during operation. A power on reset is defined as the time a reset is asserted when power is being applied to the circuit. A powered reset is defined to be when the FX1 has been previously powered on and operating and the RESET# pin is asserted. Cypress provides an application note which describes and recommends power on reset implementation and is found on the Cypress web site. While the application note discusses the FX2, the information provided applies also to the FX1. For more information on reset implementation for the FX2 family of products visit http://www.cypress.com. Figure 2. Reset Timing Plots RESET# VIL RESET# VIL 3.3 V 3.0 V 3.3 V VCC VCC 0V 0V TRESET TRESET Power on Reset Powered Reset wakeup interrupt. This applies irrespective of whether the FX1 is connected to the USB or not. Table 5. Reset Timing Values Condition TRESET Power On Reset with crystal 5 ms Power On Reset with external clock 200 s + Clock stability time Powered Reset 200 s Wakeup Pins The 8051 puts itself and the rest of the chip into a power down mode by setting PCON.0 = 1. This stops the oscillator and PLL. When WAKEUP is asserted by external logic, the oscillator restarts, after the PLL stabilizes, and then the 8051 receives a The FX1 exits the power down (USB suspend) state using one of the following methods: ■ USB bus activity (if D+/D– lines are left floating, noise on these lines may indicate activity to the FX1 and initiate a wakeup). ■ External logic asserts the WAKEUP pin. ■ External logic asserts the PA3/WU2 pin. The second wakeup pin, WU2, can also be configured as a general purpose I/O pin. This allows a simple external R-C network to be used as a periodic wakeup source. Note that WAKEUP is by default active LOW. Note 3. If the external clock is powered at the same time as the CY7C64713 and has a stabilization wait period. It must be added to the 200 s. Document Number: 38-08039 Rev. *J Page 8 of 72 [+] Feedback CY7C64713 Program/Data RAM Size The FX1 has 16 KBytes of internal program/data RAM, where PSEN#/RD# signals are internally ORed to allow the 8051 to access it as both program and data memory. No USB control registers appear in this space. Two memory maps are shown in the following diagrams: ■ Figure 3 on page 9 Internal Code Memory, EA = 0 ■ Figure 4 on page 10 External Code Memory, EA = 1. Internal Code Memory, EA = 0 external RAM or ROM is added, the external read and write strobes are suppressed for memory spaces that exist inside the chip. This allows the user to connect a 64 KByte memory without requiring the address decodes to keep clear of internal memory spaces. Only the internal 16 KBytes and scratch pad 0.5 KBytes RAM spaces have the following access: ■ USB download ■ USB upload ■ Setup data pointer ■ I2C interface boot load This mode implements the internal 16 KByte block of RAM (starting at 0) as combined code and data memory. When the Figure 3. Internal Code Memory, EA = 0. Inside FX1 Outside FX1 FFFF 7.5 KBytes USB regs and 4K FIFO buffers (RD#,WR#) E200 E1FF 0.5 KBytes RAM E000 Data (RD#,WR#)* (OK to populate data memory here—RD#/WR# strobes are not active) 40 KBytes External Data Memory (RD#,WR#) 48 KBytes External Code Memory (PSEN#) 3FFF 16 KBytes RAM Code and Data (PSEN#,RD#,WR#)* (Ok to populate data memory here—RD#/WR# strobes are not active) (OK to populate program memory here— PSEN# strobe is not active) 0000 Data Code *SUDPTR, USB upload/download, I2C interface boot access Document Number: 38-08039 Rev. *J Page 9 of 72 [+] Feedback CY7C64713 External Code Memory, EA = 1 The bottom 16 KBytes of program memory is external, and therefore the bottom 16 KBytes of internal RAM is accessible only as data memory. Figure 4. External Code Memory, EA = 1 Inside FX1 Outside FX1 FFFF 7.5 KBytes USB regs and 4K FIFO buffers (RD#,WR#) E200 E1FF 0.5 KBytes RAM E000 Data (RD#,WR#)* (OK to populate data memory here—RD#/WR# strobes are not active) 40 KBytes External Data Memory (RD#,WR#) 64 KBytes External Code Memory (PSEN#) 3FFF 16 KBytes RAM Data (RD#,WR#)* (Ok to populate data memory here—RD#/WR# strobes are not active) 0000 Data Code 2 *SUDPTR, USB upload/download, I C interface boot access Document Number: 38-08039 Rev. *J Page 10 of 72 [+] Feedback CY7C64713 Figure 5. Register Addresses FFFF 4 KBytes EP2-EP8 buffers (8 x 512) Not all Space is available for all transfer types F000 EFFF 2 KBytes RESERVED E800 E7FF E7C0 E7BF E780 E77F E740 E73F E700 E6FF E500 E4FF E480 E47F E400 E3FF E200 E1FF 64 Bytes EP1IN 64 Bytes EP1OUT 64 Bytes EP0 IN/OUT 64 Bytes RESERVED 8051 Addressable Registers (512) Reserved (128) 128 bytes GPIF Waveforms Reserved (512) 512 bytes E000 8051 xdata RAM Endpoint RAM Table 6. Default Alternate Settings Size ■ 3 × 64 bytes (Endpoints 0 and 1) ■ 8 × 512 bytes (Endpoints 2, 4, 6, 8) Organization Alternate Setting ep0 0 1 64 64 2 64 3 64 ep1out 0 64 bulk 64 int 64 int ep1in 0 64 bulk 64 int 64 int ■ EP0—Bidirectional endpoint zero, 64 byte buffer ep2 0 64 bulk out (2×) 64 int out (2×) 64 iso out (2×) ■ EP1IN, EP1OUT—64 byte buffers, bulk or interrupt ep4 0 64 bulk out (2×) 64 bulk out (2×) 64 bulk out (2×) ■ EP2, 4, 6, 8—Eight 512-byte buffers, bulk, interrupt, or isochronous, of which only the transfer size is available. EP4 and EP8 are double buffered, while EP2 and 6 are either double, triple, or quad buffered. Regardless of the physical size of the buffer, each endpoint buffer accommodates only one full speed packet. For bulk endpoints, the maximum number of bytes it can accommodate is 64, even though the physical buffer size is 512 or 1024. For an ISOCHRONOUS endpoint the maximum number of bytes it can accommodate is 1023. For endpoint configuration options, see Figure 6 on page 12. ep6 0 64 bulk in (2×) 64 int in (2×) ep8 0 64 bulk in (2×) 64 bulk in (2×) 64 bulk in (2×) Setup Data Buffer A separate 8-byte buffer at 0xE6B8-0xE6BF holds the Setup data from a CONTROL transfer. Default Alternate Settings In the following table, ‘0’ means “not implemented”, and ‘2×’ means “double buffered”. Document Number: 38-08039 Rev. *J 64 iso in (2×) External FIFO Interface Architecture The FX1 slave FIFO architecture has eight 512-byte blocks in the endpoint RAM that directly serve as FIFO memories, and are controlled by FIFO control signals (such as IFCLK, SLCS#, SLRD, SLWR, SLOE, PKTEND, and flags). The usable size of these buffers depend on the USB transfer mode as described in the section Organization. In operation, some of the eight RAM blocks fill or empty from the SIE, while the others are connected to the I/O transfer logic. The transfer logic takes two forms: the GPIF for internally generated control signals or the slave FIFO interface for externally controlled transfers. Page 11 of 72 [+] Feedback CY7C64713 Figure 6. Endpoint Configuration EP0 IN&OUT 64 64 64 EP1 IN 64 64 64 EP1 OUT 64 64 64 EP2 EP2 EP2 64 64 64 64 64 64 64 64 64 64 64 64 64 64 64 64 64 64 64 64 64 64 64 64 64 64 64 EP2 EP2 EP2 EP2 EP2 EP2 EP2 64 64 64 64 64 64 64 64 64 64 64 64 EP4 EP4 64 64 64 64 64 64 64 64 64 64 64 64 EP6 64 64 64 64 EP6 1023 EP8 64 EP6 EP6 64 64 64 64 1023 64 64 1 2 1023 3 64 1023 1023 EP6 1023 EP6 EP6 64 64 64 64 64 64 4 5 The FX1 endpoint FIFOS are implemented as eight physically distinct 256 × 16 RAM blocks. The 8051/SIE can switch any of the RAM blocks between two domains: the USB (SIE) domain and the 8051-I/O Unit domain. This switching is done instantaneously, giving essentially zero transfer time between “USB FIFOS” and “Slave FIFOS”. While they are physically the same memory, no bytes are actually transferred between buffers. At any time, some RAM blocks fill or empty with USB data under SIE control, while other RAM blocks are available to the 8051 and the I/O control unit. The RAM blocks operate as a single-port in the USB domain, and dual port in the 8051-I/O domain. The blocks are configured as single, double, triple, or quad buffered. The I/O control unit implements either an internal master (M for master) or external master (S for Slave) interface. In Master (M) mode, the GPIF internally controls FIFOADR[1..0] to select a FIFO. The RDY pins (two in the 56-pin package, six in the 100-pin and 128-pin packages) are used as flag inputs from an external FIFO or other logic if desired. The GPIF is run from either an internally derived clock or an externally supplied clock (IFCLK), at a rate that transfers data up to 96 Megabytes/s (48 MHz IFCLK with 16-bit interface). In Slave (S) mode, the FX1 accepts either an internally derived clock or an externally supplied clock (IFCLK with a maximum frequency of 48 MHz) and SLCS#, SLRD, SLWR, SLOE, PKTEND signals from external logic. When using an external IFCLK, the external clock must be present before switching to the external clock with the IFCLKSRC bit. Each endpoint can individually be selected for byte or word operation by an internal configuration bit, and a Slave FIFO Output Enable signal SLOE enables data of the selected width. External logic must ensure that the output enable signal is inactive when writing data to a slave FIFO. The slave interface can also operate asynchronously, where the SLRD and SLWR signals act directly EP6 64 64 EP6 64 1023 64 EP8 EP8 Master/Slave Control Signals Document Number: 38-08039 Rev. *J 1023 1023 1023 64 EP8 64 1023 1023 64 EP4 EP6 1023 EP2 EP2 64 1023 6 64 64 64 64 7 8 1023 9 1023 1023 1023 EP8 64 64 64 64 10 1023 11 1023 12 as strobes, rather than a clock qualifier as in the synchronous mode. The signals SLRD, SLWR, SLOE, and PKTEND are gated by the signal SLCS#. GPIF and FIFO Clock Rates An 8051 register bit selects one of two frequencies for the internally supplied interface clock: 30 MHz and 48 MHz. Alternatively, an externally supplied clock of 5 to 48 MHz feeding the IFCLK pin is used as the interface clock. IFCLK is configured to function as an output clock when the GPIF and FIFOs are internally clocked. An output enable bit in the IFCONFIG register turns this clock output off, if desired. Another bit within the IFCONFIG register inverts the IFCLK signal whether internally or externally sourced. GPIF The GPIF is a flexible 8 or 16-bit parallel interface driven by a user programmable finite state machine. It allows the CY7C64713 to perform local bus mastering, and can implement a wide variety of protocols such as ATA interface, printer parallel port, and Utopia. The GPIF has six programmable control outputs (CTL), nine address outputs (GPIFADRx), and six general purpose Ready inputs (RDY). The data bus width is 8 or 16 bits. Each GPIF vector defines the state of the control outputs, and determines what state a Ready input (or multiple inputs) must be before proceeding. The GPIF vector is programmed to advance a FIFO to the next data value, advance an address, and so on. A sequence of the GPIF vectors create a single waveform that executes to perform the data move between the FX1 and the external device. Six Control OUT Signals The 100-pin and 128-pin packages bring out all six Control Output pins (CTL0–CTL5). The 8051 programs the GPIF unit to define the CTL waveforms. The 56-pin package brings out three Page 12 of 72 [+] Feedback CY7C64713 of these signals: CTL0–CTL2. CTLx waveform edges are programmed to make transitions as fast as once per clock (20.8 ns using a 48 MHz clock). Six Ready IN Signals The 100-pin and 128-pin packages bring out all six Ready inputs (RDY0–RDY5). The 8051 programs the GPIF unit to test the RDY pins for GPIF branching. The 56 pin package brings out two of these signals, RDY0–1. Nine GPIF Address OUT Signals Nine GPIF address lines are available in the 100-pin and 128-pin packages: GPIFADR[8..0]. The GPIF address lines allow indexing through up to a 512 byte block of RAM. If more address lines are needed, I/O port pins are used. Long Transfer Mode In Master mode, the 8051 appropriately sets the GPIF transaction count registers (GPIFTCB3, GPIFTCB2, GPIFTCB1, or GPIFTCB0) for unattended transfers of up to 232 transactions. The GPIF automatically throttles data flow to prevent under or overflow until the full number of requested transactions are complete. The GPIF decrements the value in these registers to represent the current status of the transaction. ECC Generation The EZ-USB FX1 can calculate ECCs (Error Correcting Codes) on data that pass across its GPIF or Slave FIFO interfaces. There are two ECC configurations: Two ECCs, each calculated over 256 bytes (SmartMedia™ Standard); and one ECC calculated over 512 bytes. The ECC can correct any one-bit error or detect any two-bit error. Note To use the ECC logic, the GPIF or Slave FIFO interface must be configured for byte-wide operation. ECC Implementation The two ECC configurations are selected by the ECCM bit: 0.0.0.1 ECCM = 0 Two 3-byte ECCs, each calculated over a 256-byte block of data. This configuration conforms to the SmartMedia Standard. Write any value to ECCRESET, then pass data across the GPIF or Slave FIFO interface. The ECC for the first 256 bytes of data is calculated and stored in ECC1. The ECC for the next 256 bytes is stored in ECC2. After the second ECC is calculated, the values in the ECCx registers do not change until the ECCRESET is written again, even if more data is subsequently passed across the interface. 0.0.0.2 ECCM = 1 One 3-byte ECC calculated over a 512-byte block of data. Write any value to ECCRESET, then pass data across the GPIF or Slave FIFO interface. The ECC for the first 512 bytes of data is calculated and stored in ECC1; ECC2 is not used. After the ECC is calculated, the value in ECC1 does not change until the ECCRESET is written again, even if more data is subsequently passed across the interface USB Uploads and Downloads The core has the ability to directly edit the data contents of the internal 16 KByte RAM and of the internal 512 byte scratch pad RAM via a vendor specific command. This capability is normally used when ‘soft’ downloading user code and is available only to and from the internal RAM, only when the 8051 is held in reset. The available RAM spaces are 16 KBytes from 0x0000–0x3FFF (code/data) and 512 bytes from 0xE000–0xE1FF (scratch pad data RAM).[4] Autopointer Access FX1 provides two identical autopointers. They are similar to the internal 8051 data pointers, but with an additional feature: they can optionally increment after every memory access. This capability is available to and from both internal and external RAM. The autopointers are available in external FX1 registers, under the control of a mode bit (AUTOPTRSETUP.0). Using the external FX1 autopointer access (at 0xE67B–0xE67C) allows the autopointer to access all RAM, internal and external, to the part. Also, the autopointers can point to any FX1 register or endpoint buffer space. When autopointer access to external memory is enabled, the location 0xE67B and 0xE67C in XDATA and the code space cannot be used. I2C Controller FX1 has one I2C port that is driven by two internal controllers: one that automatically operates at boot time to load VID/PID/DID and configuration information; and another that the 8051, once running, uses to control external I2C devices. The I2C port operates in master mode only. I2C Port Pins The I2C pins SCL and SDA must have external 2.2 k pull up resistors even if no EEPROM is connected to the FX1. External EEPROM device address pins must be configured properly. See Table 7 for configuring the device address pins. Table 7. Strap Boot EEPROM Address Lines to These Values Bytes Example EEPROM A2 A1 A0 16 24LC00[5] N/A N/A N/A 128 24LC01 0 0 0 256 24LC02 0 0 0 4K 24LC32 0 0 1 8K 24LC64 0 0 1 16K 24LC128 0 0 1 Notes 4. After the data is downloaded from the host, a ‘loader’ executes from the internal RAM to transfer downloaded data to the external memory. 5. This EEPROM has no address pins. Document Number: 38-08039 Rev. *J Page 13 of 72 [+] Feedback CY7C64713 I2C Interface Boot Load Access I2 At power on reset the C interface boot loader loads the VID/PID/DID configuration bytes and up to 16 KBytes of program/data. The available RAM spaces are 16 KBytes from 0x0000–0x3FFF and 512 bytes from 0xE000–0xE1FF. The 8051 is in reset. I2C interface boot loads only occur after power on reset. I2C Interface General Purpose Access The 8051 can control peripherals connected to the I2C bus using the I2CTL and I2DAT registers. FX1 provides I2C master control only, because it is never an I2C slave. Compatible with Previous Generation EZ-USB FX2 The EZ-USB FX1 is fit, form, and function upgradable to the EZ-USB FX2LP. This makes for an easy transition for designers wanting to upgrade their systems from full speed to high speed designs. The pinout and package selection are identical, and all firmware developed for the FX1 function in the FX2LP with proper addition of high speed descriptors and speed switching code. Pin Assignments Figure 7 on page 15 identifies all signals for the three package types. The following pages illustrate the individual pin diagrams, Document Number: 38-08039 Rev. *J plus a combination diagram showing which of the full set of signals are available in the 128, 100, and 56-pin packages. The signals on the left edge of the 56-pin package in Figure 7 on page 15 are common to all versions in the FX1 family. Three modes are available in all package versions: Port, GPIF master, and Slave FIFO. These modes define the signals on the right edge of the diagram. The 8051 selects the interface mode using the IFCONFIG[1:0] register bits. Port mode is the power on default configuration. The 100-pin package adds functionality to the 56-pin package by adding these pins: ■ PORTC or alternate GPIFADR[7:0] address signals ■ PORTE or alternate GPIFADR[8] address signal and seven additional 8051 signals ■ Three GPIF Control signals ■ Four GPIF Ready signals ■ Nine 8051 signals (two USARTs, three timer inputs, INT4,and INT5#) ■ BKPT, RD#, WR#. The 128-pin package adds the 8051 address and data buses plus control signals. Note that two of the required signals, RD# and WR#, are present in the 100-pin version. In the 100-pin and 128-pin versions, an 8051 control bit is set to pulse the RD# and WR# pins when the 8051 reads from and writes to the PORTC. Page 14 of 72 [+] Feedback CY7C64713 Figure 7. Signals Port XTALIN XTALOUT RESET# WAKEUP# SCL SDA 56 GPIF Master PD7 PD6 PD5 PD4 PD3 PD2 PD1 PD0 PB7 PB6 PB5 PB4 PB3 PB2 PB1 PB0 INT0#/PA0 INT1#/PA1 PA2 WU2/PA3 PA4 PA5 PA6 PA7 IFCLK CLKOUT DPLUS DMINUS 100 PE7/GPIFADR8 PE6/T2EX PE5/INT6 PE4/RxD1OUT PE3/RxD0OUT PE2/T2OUT PE1/T1OUT PE0/T0OUT 128 Document Number: 38-08039 Rev. *J FD[15] FD[14] FD[13] FD[12] FD[11] FD[10] FD[9] FD[8] FD[7] FD[6] FD[5] FD[4] FD[3] FD[2] FD[1] FD[0] RDY0 RDY1 SLRD SLWR CTL0 CTL1 CTL2 FLAGA FLAGB FLAGC INT0#/PA0 INT1#/PA1 PA2 WU2/PA3 PA4 PA5 PA6 PA7 INT0#/ PA0 INT1#/ PA1 SLOE WU2/PA3 FIFOADR0 FIFOADR1 PKTEND PA7/FLAGD/SLCS# RxD0 TxD0 RxD1 TxD1 INT4 INT5# T2 T1 T0 RD# WR# CS# OE# PSEN# D7 D6 D5 D4 D3 D2 D1 D0 EA Slave FIFO CTL3 CTL4 CTL5 RDY2 RDY3 RDY4 RDY5 BKPT PORTC7/GPIFADR7 PORTC6/GPIFADR6 PORTC5/GPIFADR5 PORTC4/GPIFADR4 PORTC3/GPIFADR3 PORTC2/GPIFADR2 PORTC1/GPIFADR1 PORTC0/GPIFADR0 FD[15] FD[14] FD[13] FD[12] FD[11] FD[10] FD[9] FD[8] FD[7] FD[6] FD[5] FD[4] FD[3] FD[2] FD[1] FD[0] A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 Page 15 of 72 [+] Feedback CY7C64713 Figure 8. CY7C64713 128-pin TQFP Pin Assignment 27 28 29 30 31 32 33 34 35 36 37 38 103 26 104 25 105 24 106 23 107 22 108 21 109 20 110 19 111 18 112 17 113 16 114 15 115 14 116 13 117 12 118 11 119 10 120 9 121 8 122 7 123 6 124 5 125 4 126 3 PD1/FD9 PD2/FD10 PD3/FD11 INT5# VCC PE0/T0OUT PE1/T1OUT PE2/T2OUT PE3/RXD0OUT PE4/RXD1OUT PE5/INT6 PE6/T2EX PE7/GPIFADR8 GND A4 A5 A6 A7 PD4/FD12 PD5/FD13 PD6/FD14 PD7/FD15 GND A8 A9 A10 2 127 128 1 CLKOUT VCC GND RDY0/*SLRD RDY1/*SLWR RDY2 RDY3 RDY4 RDY5 AVCC XTALOUT XTALIN AGND NC NC NC AVCC DPLUS DMINUS AGND A11 A12 A13 A14 A15 VCC GND INT4 T0 T1 T2 *IFCLK RESERVED BKPT EA SCL SDA OE# PD0/FD8 *WAKEUP VCC RESET# CTL5 A3 A2 A1 A0 GND PA7/*FLAGD/SLCS# PA6/*PKTEND PA5/FIFOADR1 PA4/FIFOADR0 D7 D6 D5 PA3/*WU2 PA2/*SLOE PA1/INT1# PA0/INT0# VCC GND PC7/GPIFADR7 PC6/GPIFADR6 PC5/GPIFADR5 PC4/GPIFADR4 PC3/GPIFADR3 PC2/GPIFADR2 PC1/GPIFADR1 PC0/GPIFADR0 CTL2/*FLAGC CTL1/*FLAGB CTL0/*FLAGA VCC CTL4 CTL3 GND CY7C64713 128-pin TQFP 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 VCC D4 D3 D2 D1 D0 GND PB7/FD7 PB6/FD6 PB5/FD5 PB4/FD4 RXD1 TXD1 RXD0 TXD0 GND VCC PB3/FD3 PB2/FD2 PB1/FD1 PB0/FD0 VCC CS# WR# RD# PSEN# 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 * indicates programmable polarity Document Number: 38-08039 Rev. *J Page 16 of 72 [+] Feedback CY7C64713 Figure 9. CY7C64713 100-pin TQFP Pin Assignment 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 PD1/FD9 PD2/FD10 PD3/FD11 INT5# VCC PE0/T0OUT PE1/T1OUT PE2/T2OUT PE3/RXD0OUT PE4/RXD1OUT PE5/INT6 PE6/T2EX PE7/GPIFADR8 GND PD4/FD12 PD5/FD13 PD6/FD14 PD7/FD15 GND CLKOUT 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 VCC GND RDY0/*SLRD RDY1/*SLWR RDY2 RDY3 RDY4 RDY5 AVCC XTALOUT XTALIN AGND NC NC NC AVCC DPLUS DMINUS AGND VCC GND INT4 T0 T1 T2 *IFCLK RESERVED BKPT SCL SDA PD0/FD8 *WAKEUP VCC RESET# CTL5 GND PA7/*FLAGD/SLCS# PA6/*PKTEND PA5/FIFOADR1 PA4/FIFOADR0 PA3/*WU2 PA2/*SLOE PA1/INT1# PA0/INT0# VCC GND PC7/GPIFADR7 PC6/GPIFADR6 PC5/GPIFADR5 PC4/GPIFADR4 PC3/GPIFADR3 PC2/GPIFADR2 PC1/GPIFADR1 PC0/GPIFADR0 CTL2/*FLAGC CTL1/*FLAGB CTL0/*FLAGA VCC CTL4 CTL3 CY7C64713 100-pin TQFP 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 GND VCC GND PB7/FD7 PB6/FD6 PB5/FD5 PB4/FD4 RXD1 TXD1 RXD0 TXD0 GND VCC PB3/FD3 PB2/FD2 PB1/FD1 PB0/FD0 VCC WR# RD# 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 Document Number: 38-08039 Rev. *J * indicates programmable polarity Page 17 of 72 [+] Feedback CY7C64713 Figure 10. CY7C64713 56-pin SSOP Pin Assignment CY7C64713 56-pin SSOP 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 PD5/FD13 PD6/FD14 PD7/FD15 GND CLKOUT VCC GND RDY0/*SLRD RDY1/*SLWR AVCC XTALOUT XTALIN AGND AVCC DPLUS DMINUS AGND VCC GND *IFCLK RESERVED SCL SDA VCC PB0/FD0 PB1/FD1 PB2/FD2 PB3/FD3 PD4/FD12 PD3/FD11 PD2/FD10 PD1/FD9 PD0/FD8 *WAKEUP VCC RESET# GND PA7/*FLAGD/SLCS# PA6/PKTEND PA5/FIFOADR1 PA4/FIFOADR0 PA3/*WU2 PA2/*SLOE PA1/INT1# PA0/INT0# VCC CTL2/*FLAGC CTL1/*FLAGB CTL0/*FLAGA GND VCC GND PB7/FD7 PB6/FD6 PB5/FD5 PB4/FD4 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 * indicates programmable polarity Document Number: 38-08039 Rev. *J Page 18 of 72 [+] Feedback CY7C64713 Figure 11. CY7C64713 56-pin QFN Pin Assignment GND VCC CLKOUT GND PD7/FD15 PD6/FD14 PD5/FD13 PD4/FD12 PD3/FD11 PD2/FD10 PD1/FD9 PD0/FD8 *WAKEUP VCC 56 55 54 53 52 51 50 49 48 47 46 45 44 43 RDY0/*SLRD 1 42 RESET# RDY1/*SLWR 2 41 GND AVCC 3 40 PA7/*FLAGD/SLCS# XTALOUT 4 39 PA6/*PKTEND XTALIN 5 38 PA5/FIFOADR1 AGND 6 37 PA4/FIFOADR0 AVCC 7 36 PA3/*WU2 DPLUS 8 35 PA2/*SLOE DMINUS 9 34 PA1/INT1# AGND 10 33 PA0/INT0# VCC 11 32 VCC GND 12 31 CTL2/*FLAGC *IFCLK 13 30 CTL1/*FLAGB RESERVED 14 29 CTL0/*FLAGA CY7C64713 56-pin QFN 15 16 17 18 19 20 21 22 23 24 25 26 27 28 SCL SDA VCC PB0/FD0 PB1/FD1 PB2/FD2 PB3/FD3 PB4/FD4 PB5/FD5 PB6/FD6 PB7/FD7 GND VCC GND * indicates programmable polarity Document Number: 38-08039 Rev. *J Page 19 of 72 [+] Feedback CY7C64713 CY7C64713 Pin Definitions The FX1 Pin Definitions for CY7C64713 follow.[6] Table 8. FX1 Pin Definitions 128-pin 100-pin 56-pin TQFP TQFP SSOP 56-pin QFN Name Type Default Description 10 9 10 3 AVCC Power N/A Analog VCC. Connect this pin to 3.3 V power source. This signal provides power to the analog section of the chip. 17 16 14 7 AVCC Power N/A Analog VCC. Connect this pin to 3.3 V power source. This signal provides power to the analog section of the chip. 13 12 13 6 AGND Ground N/A Analog Ground. Connect to ground with as short a path as possible. 20 19 17 10 AGND Ground N/A Analog Ground. Connect to ground with as short a path as possible. 19 18 16 9 DMINUS I/O/Z Z 18 17 15 8 USB D– Signal. Connect to the USB D– signal. DPLUS I/O/Z Z USB D+ Signal. Connect to the USB D+ signal. 94 A0 Output L 95 A1 Output L 96 A2 Output L 8051 Address Bus. This bus is driven at all times. When the 8051 is addressing the internal RAM it reflects the internal address. 97 A3 Output L 117 A4 Output L 118 A5 Output L 119 A6 Output L 120 A7 Output L 126 A8 Output L 127 A9 Output L 128 A10 Output L 21 A11 Output L 22 A12 Output L 23 A13 Output L 24 A14 Output L 25 A15 Output L 59 D0 I/O/Z Z 60 D1 I/O/Z Z 61 D2 I/O/Z Z 62 D3 I/O/Z Z 63 D4 I/O/Z Z 86 D5 I/O/Z Z 87 D6 I/O/Z Z 88 D7 I/O/Z Z 39 PSEN# Output H 8051 Data Bus. This bidirectional bus is high impedance when inactive, input for bus reads, and output for bus writes. The data bus is used for external 8051 program and data memory. The data bus is active only for external bus accesses, and is driven LOW in suspend. Program Store Enable. This active LOW signal indicates an 8051 code fetch from external memory. It is active for program memory fetches from 0x4000–0xFFFF when the EA pin is LOW, or from 0x0000–0xFFFF when the EA pin is HIGH. Note 6. Do not leave unused inputs floating. Tie either HIGH or LOW as appropriate. Pull outputs up or down to ensure signals at power up and in standby. Note that no pins must be driven when the device is powered down. Document Number: 38-08039 Rev. *J Page 20 of 72 [+] Feedback CY7C64713 Table 8. FX1 Pin Definitions (continued) 128-pin 100-pin 56-pin TQFP TQFP SSOP 34 28 99 77 49 56-pin QFN 42 35 Name Type Default Description BKPT Output L Breakpoint. This pin goes active (HIGH) when the 8051 address bus matches the BPADDRH/L registers and breakpoints are enabled in the BREAKPT register (BPEN = 1). If the BPPULSE bit in the BREAKPT register is HIGH, this signal pulses HIGH for eight 12-/24-/48 MHz clocks. If the BPPULSE bit is LOW, the signal remains HIGH until the 8051 clears the BREAK bit (by writing ‘1’ to it) in the BREAKPT register. RESET# Input N/A Active LOW Reset. Resets the entire chip. See the section Reset and Wakeup on page 8 for more details. EA Input N/A External Access. This pin determines where the 8051 fetches code between addresses 0x0000 and 0x3FFF. If EA = 0 the 8051 fetches this code from its internal RAM. IF EA = 1 the 8051 fetches this code from external memory. XTALIN Input N/A Crystal Input. Connect this signal to a 24 MHz parallel-resonant, fundamental mode crystal and load capacitor to GND. It is also correct to drive the XTALIN with an external 24 MHz square wave derived from another clock source. When driving from an external source, the driving signal must be a 3.3 V square wave. N/A Crystal Output. Connect this signal to a 24 MHz parallel-resonant, fundamental mode crystal and load capacitor to GND. If an external clock is used to drive XTALIN, leave this pin open. 12 11 12 5 11 10 11 4 XTALOUT Output 1 100 5 54 CLKOUT O/Z 12 MHz CLKOUT. 12, 24 or 48 MHz clock, phase locked to the 24 MHz input clock. The 8051 defaults to 12 MHz operation. The 8051 may three-state this output by setting CPUCS.1 = 1. 82 67 40 33 PA0 or INT0# I/O/Z I (PA0) Multiplexed pin whose function is selected by PORTACFG.0 PA0 is a bidirectional I/O port pin. INT0# is the active-LOW 8051 INT0 interrupt input signal, which is either edge triggered (IT0 = 1) or level triggered (IT0 = 0). 83 68 41 34 PA1 or INT1# I/O/Z I (PA1) Multiplexed pin whose function is selected by: PORTACFG.1 PA1 is a bidirectional I/O port pin. INT1# is the active-LOW 8051 INT1 interrupt input signal, which is either edge triggered (IT1 = 1) or level triggered (IT1 = 0). 84 69 42 35 PA2 or SLOE I/O/Z I (PA2) Multiplexed pin whose function is selected by two bits: IFCONFIG[1:0]. PA2 is a bidirectional I/O port pin. SLOE is an input-only output enable with programmable polarity (FIFOPINPOLAR.4) for the slave FIFOs connected to FD[7..0] or FD[15..0]. 85 70 43 36 PA3 or WU2 I/O/Z I (PA3) Multiplexed pin whose function is selected by: WAKEUP.7 and OEA.3 PA3 is a bidirectional I/O port pin. WU2 is an alternate source for USB Wakeup, enabled by WU2EN bit (WAKEUP.1) and polarity set by WU2POL (WAKEUP.4). If the 8051 is in suspend and WU2EN = 1, a transition on this pin starts up the oscillator and interrupts the 8051 to allow it to exit the suspend mode. Asserting this pin inhibits the chip from suspending, if WU2EN = 1. Port A Document Number: 38-08039 Rev. *J Page 21 of 72 [+] Feedback CY7C64713 Table 8. FX1 Pin Definitions (continued) 128-pin 100-pin 56-pin TQFP TQFP SSOP 56-pin QFN Name Type Default Description 89 71 44 37 PA4 or FIFOADR0 I/O/Z I (PA4) Multiplexed pin whose function is selected by: IFCONFIG[1..0]. PA4 is a bidirectional I/O port pin. FIFOADR0 is an input-only address select for the slave FIFOs connected to FD[7..0] or FD[15..0]. 90 72 45 38 PA5 or FIFOADR1 I/O/Z I (PA5) Multiplexed pin whose function is selected by: IFCONFIG[1..0]. PA5 is a bidirectional I/O port pin. FIFOADR1 is an input-only address select for the slave FIFOs connected to FD[7..0] or FD[15..0]. 91 73 46 39 PA6 or PKTEND I/O/Z I (PA6) Multiplexed pin whose function is selected by the IFCONFIG[1:0] bits. PA6 is a bidirectional I/O port pin. PKTEND is an input used to commit the FIFO packet data to the endpoint and whose polarity is programmable via FIFOPINPOLAR.5. 92 74 47 40 PA7 or FLAGD or SLCS# I/O/Z I (PA7) Multiplexed pin whose function is selected by the IFCONFIG[1:0] and PORTACFG.7 bits. PA7 is a bidirectional I/O port pin. FLAGD is a programmable slave-FIFO output status flag signal. SLCS# gates all other slave FIFO enable/strobes 44 34 25 18 PB0 or FD[0] I/O/Z I (PB0) Multiplexed pin whose function is selected by the following bits: IFCONFIG[1..0]. PB0 is a bidirectional I/O port pin. FD[0] is the bidirectional FIFO/GPIF data bus. 45 35 26 19 PB1 or FD[1] I/O/Z I (PB1) Multiplexed pin whose function is selected by the following bits: IFCONFIG[1..0]. PB1 is a bidirectional I/O port pin. FD[1] is the bidirectional FIFO/GPIF data bus. 46 36 27 20 PB2 or FD[2] I/O/Z I (PB2) Multiplexed pin whose function is selected by the following bits: IFCONFIG[1..0]. PB2 is a bidirectional I/O port pin. FD[2] is the bidirectional FIFO/GPIF data bus. 47 37 28 21 PB3 or FD[3] I/O/Z I (PB3) Multiplexed pin whose function is selected by the following bits: IFCONFIG[1..0]. PB3 is a bidirectional I/O port pin. FD[3] is the bidirectional FIFO/GPIF data bus. 54 44 29 22 PB4 or FD[4] I/O/Z I (PB4) Multiplexed pin whose function is selected by the following bits: IFCONFIG[1..0]. PB4 is a bidirectional I/O port pin. FD[4] is the bidirectional FIFO/GPIF data bus. 55 45 30 23 PB5 or FD[5] I/O/Z I (PB5) Multiplexed pin whose function is selected by the following bits: IFCONFIG[1..0]. PB5 is a bidirectional I/O port pin. FD[5] is the bidirectional FIFO/GPIF data bus. 56 46 31 24 PB6 or FD[6] I/O/Z I (PB6) Multiplexed pin whose function is selected by the following bits: IFCONFIG[1..0]. PB6 is a bidirectional I/O port pin. FD[6] is the bidirectional FIFO/GPIF data bus. Port B Document Number: 38-08039 Rev. *J Page 22 of 72 [+] Feedback CY7C64713 Table 8. FX1 Pin Definitions (continued) 128-pin 100-pin 56-pin TQFP TQFP SSOP 57 47 32 56-pin QFN Name Type Default 25 PB7 or FD[7] I/O/Z I (PB7) Multiplexed pin whose function is selected by the following bits: IFCONFIG[1..0]. PB7 is a bidirectional I/O port pin. FD[7] is the bidirectional FIFO/GPIF data bus. Description PORT C 72 57 PC0 or GPIFADR0 I/O/Z I (PC0) Multiplexed pin whose function is selected by PORTCCFG.0 PC0 is a bidirectional I/O port pin. GPIFADR0 is a GPIF address output pin. 73 58 PC1 or GPIFADR1 I/O/Z I (PC1) Multiplexed pin whose function is selected by PORTCCFG.1 PC1 is a bidirectional I/O port pin. GPIFADR1 is a GPIF address output pin. 74 59 PC2 or GPIFADR2 I/O/Z I (PC2) Multiplexed pin whose function is selected by PORTCCFG.2 PC2 is a bidirectional I/O port pin. GPIFADR2 is a GPIF address output pin. 75 60 PC3 or GPIFADR3 I/O/Z I (PC3) Multiplexed pin whose function is selected by PORTCCFG.3 PC3 is a bidirectional I/O port pin. GPIFADR3 is a GPIF address output pin. 76 61 PC4 or GPIFADR4 I/O/Z I (PC4) Multiplexed pin whose function is selected by PORTCCFG.4 PC4 is a bidirectional I/O port pin. GPIFADR4 is a GPIF address output pin. 77 62 PC5 or GPIFADR5 I/O/Z I (PC5) Multiplexed pin whose function is selected by PORTCCFG.5 PC5 is a bidirectional I/O port pin. GPIFADR5 is a GPIF address output pin. 78 63 PC6 or GPIFADR6 I/O/Z I (PC6) Multiplexed pin whose function is selected by PORTCCFG.6 PC6 is a bidirectional I/O port pin. GPIFADR6 is a GPIF address output pin. 79 64 PC7 or GPIFADR7 I/O/Z I (PC7) Multiplexed pin whose function is selected by PORTCCFG.7 PC7 is a bidirectional I/O port pin. GPIFADR7 is a GPIF address output pin. PORT D 102 80 52 45 PD0 or FD[8] I/O/Z I (PD0) Multiplexed pin whose function is selected by IFCONFIG[1..0] and EPxFIFOCFG.0 (wordwide) bits. FD[8] is the bidirectional FIFO/GPIF data bus. the 103 81 53 46 PD1 or FD[9] I/O/Z I (PD1) Multiplexed pin whose function is selected by IFCONFIG[1..0] and EPxFIFOCFG.0 (wordwide) bits. FD[9] is the bidirectional FIFO/GPIF data bus. the 104 82 54 47 PD2 or FD[10] I/O/Z I (PD2) Multiplexed pin whose function is selected by IFCONFIG[1..0] and EPxFIFOCFG.0 (wordwide) bits. FD[10] is the bidirectional FIFO/GPIF data bus. the 105 83 55 48 PD3 or FD[11] I/O/Z I (PD3) Multiplexed pin whose function is selected by IFCONFIG[1..0] and EPxFIFOCFG.0 (wordwide) bits. FD[11] is the bidirectional FIFO/GPIF data bus. the 121 95 56 49 PD4 or FD[12] I/O/Z I (PD4) Multiplexed pin whose function is selected by IFCONFIG[1..0] and EPxFIFOCFG.0 (wordwide) bits. FD[12] is the bidirectional FIFO/GPIF data bus. the 122 96 1 50 PD5 or FD[13] I/O/Z I (PD5) Multiplexed pin whose function is selected by IFCONFIG[1..0] and EPxFIFOCFG.0 (wordwide) bits. FD[13] is the bidirectional FIFO/GPIF data bus. the 123 97 2 51 PD6 or FD[14] I/O/Z I (PD6) Multiplexed pin whose function is selected by IFCONFIG[1..0] and EPxFIFOCFG.0 (wordwide) bits. FD[14] is the bidirectional FIFO/GPIF data bus. the Document Number: 38-08039 Rev. *J Page 23 of 72 [+] Feedback CY7C64713 Table 8. FX1 Pin Definitions (continued) 128-pin 100-pin 56-pin TQFP TQFP SSOP 124 98 3 56-pin QFN Name Type Default 52 PD7 or FD[15] I/O/Z I (PD7) Multiplexed pin whose function is selected by IFCONFIG[1..0] and EPxFIFOCFG.0 (wordwide) bits. FD[15] is the bidirectional FIFO/GPIF data bus. Description the Port E 108 86 PE0 or T0OUT I/O/Z I (PE0) Multiplexed pin whose function is selected by the PORTECFG.0 bit. PE0 is a bidirectional I/O port pin. T0OUT is an active HIGH signal from 8051 Timer-counter0. T0OUT outputs a high level for one CLKOUT clock cycle when Timer0 overflows. If Timer0 is operated in Mode 3 (two separate timer/counters), T0OUT is active when the low byte timer/counter overflows. 109 87 PE1 or T1OUT I/O/Z I (PE1) Multiplexed pin whose function is selected by the PORTECFG.1 bit. PE1 is a bidirectional I/O port pin. T1OUT is an active HIGH signal from 8051 Timer-counter1. T1OUT outputs a high level for one CLKOUT clock cycle when Timer1 overflows. If Timer1 is operated in Mode 3 (two separate timer/counters), T1OUT is active when the low byte timer/counter overflows. 110 88 PE2 or T2OUT I/O/Z I (PE2) Multiplexed pin whose function is selected by the PORTECFG.2 bit. PE2 is a bidirectional I/O port pin. T2OUT is the active HIGH output signal from 8051 Timer2. T2OUT is active (HIGH) for one clock cycle when Timer/Counter 2 overflows. 111 89 PE3 or RXD0OUT I/O/Z I (PE3) Multiplexed pin whose function is selected by the PORTECFG.3 bit. PE3 is a bidirectional I/O port pin. RXD0OUT is an active HIGH signal from 8051 UART0. If RXD0OUT is selected and UART0 is in Mode 0, this pin provides the output data for UART0 only when it is in sync mode. Otherwise it is a 1. 112 90 PE4 or RXD1OUT I/O/Z I (PE4) Multiplexed pin whose function is selected by the PORTECFG.4 bit. PE4 is a bidirectional I/O port pin. RXD1OUT is an active HIGH output from 8051 UART1. When the RXD1OUT is selected and UART1 is in Mode 0, this pin provides the output data for UART1 only when it is in sync mode. In Modes 1, 2, and 3, this pin is HIGH. 113 91 PE5 or INT6 I/O/Z I (PE5) Multiplexed pin whose function is selected by the PORTECFG.5 bit. PE5 is a bidirectional I/O port pin. INT6 is the 8051 INT6 interrupt request input signal. The INT6 pin is edge-sensitive, active HIGH. 114 92 PE6 or T2EX I/O/Z I (PE6) Multiplexed pin whose function is selected by the PORTECFG.6 bit. PE6 is a bidirectional I/O port pin. T2EX is an active HIGH input signal to the 8051 Timer2. T2EX reloads timer 2 on its falling edge. T2EX is active only if the EXEN2 bit is set in T2CON. 115 93 PE7 or GPIFADR8 I/O/Z I (PE7) Multiplexed pin whose function is selected by the PORTECFG.7 bit. PE7 is a bidirectional I/O port pin. GPIFADR8 is a GPIF address output pin. Document Number: 38-08039 Rev. *J Page 24 of 72 [+] Feedback CY7C64713 Table 8. FX1 Pin Definitions (continued) 128-pin 100-pin 56-pin TQFP TQFP SSOP 56-pin QFN Name Type Default Description 4 3 8 1 RDY0 or SLRD Input N/A Multiplexed pin whose function is selected by the following bits: IFCONFIG[1..0]. RDY0 is a GPIF input signal. SLRD is the input-only read strobe with programmable polarity (FIFOPINPOLAR.3) for the slave FIFOs connected to FD[7..0] or FD[15..0]. 5 4 9 2 RDY1 or SLWR Input N/A Multiplexed pin whose function is selected by the following bits: IFCONFIG[1..0]. RDY1 is a GPIF input signal. SLWR is the input-only write strobe with programmable polarity (FIFOPINPOLAR.2) for the slave FIFOs connected to FD[7..0] or FD[15..0]. 6 5 RDY2 Input N/A RDY2 is a GPIF input signal. 7 6 RDY3 Input N/A RDY3 is a GPIF input signal. 8 7 RDY4 Input N/A RDY4 is a GPIF input signal. 9 8 RDY5 Input N/A 69 54 36 29 CTL0 or FLAGA O/Z H Multiplexed pin whose function is selected by the following bits: IFCONFIG[1..0]. CTL0 is a GPIF control output. FLAGA is a programmable slave-FIFO output status flag signal. Defaults to programmable for the FIFO selected by the FIFOADR[1:0] pins. RDY5 is a GPIF input signal. 70 55 37 30 CTL1 or FLAGB O/Z H Multiplexed pin whose function is selected by the following bits: IFCONFIG[1..0]. CTL1 is a GPIF control output. FLAGB is a programmable slave-FIFO output status flag signal. Defaults to FULL for the FIFO selected by the FIFOADR[1:0] pins. 71 56 38 31 CTL2 or FLAGC O/Z H Multiplexed pin whose function is selected by the following bits: IFCONFIG[1..0]. CTL2 is a GPIF control output. FLAGC is a programmable slave-FIFO output status flag signal. Defaults to EMPTY for the FIFO selected by the FIFOADR[1:0] pins. 66 51 CTL3 O/Z H CTL3 is a GPIF control output. 67 52 CTL4 Output H CTL4 is a GPIF control output. 98 76 32 26 28 106 CTL5 Output H CTL5 is a GPIF control output. IFCLK I/O/Z Z Interface Clock, used for synchronously clocking data into or out of the slave FIFOs. IFCLK also serves as a timing reference for all slave FIFO control signals and GPIF. When internal clocking is used (IFCONFIG.7 = 1) the IFCLK pin is configured to output 30/48 MHz by bits IFCONFIG.5 and IFCONFIG.6. IFCLK may be inverted, whether internally or externally sourced, by setting the bit IFCONFIG.4 = 1. 22 INT4 Input N/A INT4 is the 8051 INT4 interrupt request input signal. The INT4 pin is edge-sensitive, active HIGH. 84 INT5# Input N/A INT5# is the 8051 INT5 interrupt request input signal. The INT5 pin is edge-sensitive, active LOW. 20 13 Document Number: 38-08039 Rev. *J Page 25 of 72 [+] Feedback CY7C64713 Table 8. FX1 Pin Definitions (continued) 128-pin 100-pin 56-pin TQFP TQFP SSOP 56-pin QFN Name Type Default Description 31 25 T2 Input N/A T2 is the active-HIGH T2 input signal to 8051 Timer2, which provides the input to Timer2 when C/T2 = 1. When C/T2 = 0, Timer2 does not use this pin. 30 24 T1 Input N/A T1 is the active-HIGH T1 signal for 8051 Timer1, which provides the input to Timer1 when C/T1 is 1. When C/T1 is 0, Timer1 does not use this bit. 29 23 T0 Input N/A T0 is the active-HIGH T0 signal for 8051 Timer0, which provides the input to Timer0 when C/T0 is 1. When C/T0 is 0, Timer0 does not use this bit. 53 43 RXD1 Input N/A RXD1 is an active-HIGH input signal for 8051 UART1, which provides data to the UART in all modes. 52 42 TXD1 Output H TXD1 is an active-HIGH output pin from 8051 UART1, which provides the output clock in sync mode, and the output data in async mode. 51 41 RXD0 Input N/A RXD0 is the active-HIGH RXD0 input to 8051 UART0, which provides data to the UART in all modes. 50 40 TXD0 Output H TXD0 is the active-HIGH TXD0 output from 8051 UART0, which provides the output clock in sync mode, and the output data in async mode. CS# Output H CS# is the active-LOW chip select for external memory. 41 32 WR# Output H WR# is the active-LOW write strobe output for external memory. 40 31 42 38 RD# Output H RD# is the active-LOW read strobe output for external memory. OE# Output H OE# is the active LOW output enable for external memory. 33 27 21 14 Reserved Input N/A Reserved. Connect to ground. 101 79 51 44 WAKEUP Input N/A USB Wakeup. If the 8051 is in suspend, asserting this pin starts up the oscillator and interrupts the 8051 to allow it to exit the suspend mode. Holding WAKEUP asserted inhibits the EZ-USB FX1 chip from suspending. This pin has programmable polarity (WAKEUP.4). 36 29 22 15 SCL OD Z Clock for the I2C interface. Connect to VCC with a 2.2K resistor, even if no I2C peripheral is attached. 37 30 23 16 SDA OD Z Data for I2C interface. Connect to VCC with a 2.2K resistor, even if no I2C peripheral is attached. 2 1 6 55 VCC Power N/A VCC. Connect to 3.3 V power source. 26 20 18 11 VCC Power N/A VCC. Connect to 3.3 V power source. 43 33 24 17 48 38 64 49 68 53 34 27 VCC Power N/A VCC. Connect to 3.3 V power source. VCC Power N/A VCC. Connect to 3.3 V power source. VCC Power N/A VCC. Connect to 3.3 V power source. VCC Power N/A VCC. Connect to 3.3 V power source. 81 66 39 32 VCC Power N/A VCC. Connect to 3.3 V power source. 100 78 50 43 VCC Power N/A VCC. Connect to 3.3 V power source. 107 85 VCC Power N/A VCC. Connect to 3.3 V power source. 3 2 7 56 GND Ground N/A Ground. 27 21 19 12 GND Ground N/A Ground. Document Number: 38-08039 Rev. *J Page 26 of 72 [+] Feedback CY7C64713 Table 8. FX1 Pin Definitions (continued) 128-pin 100-pin 56-pin TQFP TQFP SSOP 49 56-pin QFN 39 Name Type Default GND Ground N/A Description Ground. 58 48 33 26 GND Ground N/A Ground. 65 50 35 28 GND Ground N/A Ground. 48 41 4 53 80 65 93 75 116 94 125 99 14 13 GND Ground N/A Ground. GND Ground N/A Ground. GND Ground N/A Ground. GND Ground N/A Ground. NC N/A N/A No Connect. This pin must be left open. 15 14 NC N/A N/A No Connect. This pin must be left open. 16 15 NC N/A N/A No Connect. This pin must be left open. Document Number: 38-08039 Rev. *J Page 27 of 72 [+] Feedback CY7C64713 Register Summary FX1 register bit definitions are described in the EZ-USB TRM in greater detail. Table 9. FX1 Register Summary Hex Size Name Description b7 GPIF Waveform Memories E400 128 WAVEDATA GPIF D7 Waveform Descriptor 0, 1, 2, 3 data E480 128 reserved GENERAL CONFIGURATION E600 1 CPUCS CPU Control 0 & Status E601 1 IFCONFIG Interface IFCLKSRC Configuration (Ports, GPIF, slave FIFOs) E602 1 PINFLAGSAB[7] Slave FIFO FLAGB3 FLAGA and FLAGB Pin Configuration E603 1 PINFLAGSCD[7] Slave FIFO FLAGD3 FLAGC and FLAGD Pin Configuration E604 1 FIFORESET[7] Restore NAKALL FIFOS to default state E605 1 BREAKPT Breakpoint 0 Control E606 1 BPADDRH Breakpoint A15 Address H E607 1 BPADDRL Breakpoint A7 Address L E608 1 UART230 230 Kbaud 0 internally generated ref. clock E609 1 FIFOPINPOLAR[7] Slave FIFO 0 Interface pins polarity E60A 1 REVID Chip Revision rv7 E60B 1 REVCTL[7] Chip Revision Control 0 b6 b5 b4 b3 b2 b1 b0 Default Access D6 D5 D4 D3 D2 D1 D0 xxxxxxxx CLKSPD0 CLKINV CLKOE 8051RES 0 PORTCSTB CLKSPD1 RW 00000010 rrbbbbbr 3048MHZ IFCLKOE IFCLKPOL ASYNC GSTATE IFCFG1 IFCFG0 10000000 RW FLAGB2 FLAGB1 FLAGB0 FLAGA3 FLAGA2 FLAGA1 FLAGA0 00000000 RW FLAGD2 FLAGD1 FLAGD0 FLAGC3 FLAGC2 FLAGC1 FLAGC0 00000000 RW 0 0 0 EP3 EP2 EP1 EP0 xxxxxxxx W 0 0 0 BREAK BPPULSE BPEN 0 A14 A13 A12 A11 A10 A9 A8 xxxxxxxx RW A6 A5 A4 A3 A2 A1 A0 xxxxxxxx RW 0 0 0 0 0 230UART1 0 PKTEND SLOE SLRD SLWR EF FF 00000000 rrbbbbbb rv6 rv5 rv4 rv3 rv2 rv1 rv0 0 0 0 0 0 dyn_out enh_pkt RevA R 00000001 00000000 rrrrrrbb 00000000 rrrrbbbr 230UART0 00000000 rrrrrrbb Note 7. Read and writes to these register may require synchronization delay, see the section “Synchronization Delay” in the EZ-USB TRM. Document Number: 38-08039 Rev. *J Page 28 of 72 [+] Feedback CY7C64713 Table 9. FX1 Register Summary (continued) Hex Size E60C 1 3 E610 1 E611 1 E612 1 E613 1 E614 1 E615 1 E618 2 1 E619 1 E61A 1 E61B 1 E61C E620 4 1 E621 1 Name UDMA GPIFHOLDAMOUNT Description MSTB Hold Time (for UDMA) reserved ENDPOINT CONFIGURATION EP1OUTCFG Endpoint 1-OUT Configuration EP1INCFG Endpoint 1-IN Configuration EP2CFG Endpoint 2 Configuration EP4CFG Endpoint 4 Configuration EP6CFG Endpoint 6 Configuration EP8CFG Endpoint 8 Configuration reserved EP2FIFOCFG[8] Endpoint 2 / slave FIFO configuration EP4FIFOCFG[8] Endpoint 4 / slave FIFO configuration EP6FIFOCFG[8] Endpoint 6 / slave FIFO configuration EP8FIFOCFG[8] Endpoint 8 / slave FIFO configuration reserved EP2AUTOINLENH[8] Endpoint 2 AUTOIN Packet Length H EP2AUTOINLENL[8] Endpoint 2 AUTOIN Packet Length L b7 b6 b5 b4 b3 b2 b1 b0 Default Access 0 0 0 0 0 0 VALID 0 TYPE1 TYPE0 0 0 0 0 10100000 brbbrrrr VALID 0 TYPE1 TYPE0 0 0 0 0 10100000 brbbrrrr VALID DIR TYPE1 TYPE0 SIZE 0 BUF1 BUF0 10100010 bbbbbrbb VALID DIR TYPE1 TYPE0 0 0 0 0 10100000 bbbbrrrr VALID DIR TYPE1 TYPE0 SIZE 0 BUF1 BUF0 11100010 bbbbbrbb VALID DIR TYPE1 TYPE0 0 0 0 0 11100000 bbbbrrrr 0 INFM1 OEP1 AUTOOUT AUTOIN ZEROLENIN 0 WORDWIDE 00000101 rbbbbbrb 0 INFM1 OEP1 AUTOOUT AUTOIN ZEROLENIN 0 WORDWIDE 00000101 rbbbbbrb 0 INFM1 OEP1 AUTOOUT AUTOIN ZEROLENIN 0 WORDWIDE 00000101 rbbbbbrb 0 INFM1 OEP1 AUTOOUT AUTOIN ZEROLENIN 0 WORDWIDE 00000101 rbbbbbrb 0 0 0 0 0 PL10 PL9 PL8 00000010 rrrrrbbb PL7 PL6 PL5 PL4 PL3 PL2 PL1 PL0 00000000 HOLDTIME1 HOLDTIME0 00000000 rrrrrrbb RW Note 8. Read and writes to these register may require synchronization delay, see the section “Synchronization Delay” in the EZ-USB TRM. Document Number: 38-08039 Rev. *J Page 29 of 72 [+] Feedback CY7C64713 Table 9. FX1 Register Summary (continued) Hex Size Name E622 1 EP4AUTOINLENH[9] E623 1 EP4AUTOINLENL[9] E624 1 EP6AUTOINLENH[9] E625 1 EP6AUTOINLENL[9] E626 1 EP8AUTOINLENH[9] E627 1 EP8AUTOINLENL[9] E628 1 ECCCFG E629 E62A 1 1 ECCRESET ECC1B0 E62B 1 ECC1B1 E62C 1 ECC1B2 E62D 1 ECC2B0 E62E 1 ECC2B1 E62F 1 ECC2B2 Description b7 b6 b5 b4 b3 b2 b1 b0 Endpoint 4 AUTOIN Packet Length H Endpoint 4 AUTOIN Packet Length L Endpoint 6 AUTOIN Packet Length H Endpoint 6 AUTOIN Packet Length L Endpoint 8 AUTOIN Packet Length H Endpoint 8 AUTOIN Packet Length L ECC Configuration ECC Reset ECC1 Byte 0 Address ECC1 Byte 1 Address ECC1 Byte 2 Address ECC2 Byte 0 Address ECC2 Byte 1 Address ECC2 Byte 2 Address 0 0 0 0 0 0 PL9 PL8 00000010 rrrrrrbb Default Access PL7 PL6 PL5 PL4 PL3 PL2 PL1 PL0 00000000 0 0 0 0 0 PL10 PL9 PL8 00000010 rrrrrbbb PL7 PL6 PL5 PL4 PL3 PL2 PL1 PL0 00000000 0 0 0 0 0 0 PL9 PL8 00000010 rrrrrrbb PL7 PL6 PL5 PL4 PL3 PL2 PL1 PL0 00000000 0 0 0 0 0 0 0 ECCM 00000000 rrrrrrrb x LINE15 x LINE14 x LINE13 x LINE12 x LINE11 x LINE10 x LINE9 x LINE8 00000000 11111111 W R LINE7 LINE6 LINE5 LINE4 LINE3 LINE2 LINE1 LINE0 11111111 R COL5 COL4 COL3 COL2 COL1 COL0 LINE17 LINE16 11111111 R LINE15 LINE14 LINE13 LINE12 LINE11 LINE10 LINE9 LINE8 11111111 R LINE7 LINE6 LINE5 LINE4 LINE3 LINE2 LINE1 LINE0 11111111 R COL5 COL4 COL3 COL2 COL1 COL0 0 0 11111111 R RW RW RW Note 9. Read and writes to these register may require synchronization delay, see the section “Synchronization Delay” in the EZ-USB TRM. Document Number: 38-08039 Rev. *J Page 30 of 72 [+] Feedback CY7C64713 Table 9. FX1 Register Summary (continued) Hex Size Name Description b7 b6 Endpoint 2 / slave FIFO Programmable Flag H ISO Mode Endpoint 2 / slave FIFO Programmable Flag H Non-ISO Mode DECIS PKTSTAT DECIS PKTSTAT E630 1 EP2FIFOPFH[10] E630 1 EP2FIFOPFH[10] E631 1 EP2FIFOPFL[10] Endpoint 2 / IN:PKTS[1] IN:PKTS[0] slave FIFO OUT:PFC7 OUT:PFC6 Programmable Flag L E632 1 EP4FIFOPFH[10] E632 1 EP4FIFOPFH[10] Endpoint 4 / slave FIFO Programmable Flag H ISO Mode Endpoint 4 / slave FIFO Programmable Flag H Non-ISO Mode E633 1 EP4FIFOPFL[10] Endpoint 4 / IN: PKTS[1] IN: PKTS[0] slave FIFO OUT:PFC7 OUT:PFC6 Programmable Flag L E634 1 EP6FIFOPFH[10] E634 1 EP6FIFOPFH[10] Endpoint 6 / slave FIFO Programmable Flag H ISO Mode Endpoint 6 / slave FIFO Programmable Flag H Non-ISO Mode b5 b2 b1 b0 Default Access IN: PKTS[2] IN: PKTS[1] IN: PKTS[0] OUT:PFC12 OUT:PFC11 OUT:PFC10 0 PFC9 PFC8 10001000 bbbbbrbb OUT:PFC12 OUT:PFC11 OUT:PFC10 0 PFC9 PFC2 PFC1 PFC0 00000000 PFC5 b4 PFC4 b3 PFC3 IN:PKTS[2] 10001000 bbbbbrbb OUT:PFC8 RW DECIS PKTSTAT 0 IN: PKTS[1] IN: PKTS[0] OUT:PFC10 OUT:PFC9 0 0 PFC8 10001000 bbrbbrrb DECIS PKTSTAT 0 OUT:PFC10 OUT:PFC9 0 0 PFC8 10001000 bbrbbrrb PFC2 PFC1 PFC0 00000000 PFC8 00001000 bbbbbrbb PFC5 PFC4 PFC3 DECIS PKTSTAT INPKTS[2] IN: PKTS[1] IN: PKTS[0] OUT:PFC12 OUT:PFC11 OUT:PFC10 0 PFC9 DECIS PKTSTAT OUT:PFC12 OUT:PFC11 OUT:PFC10 0 PFC9 RW IN:PKTS[2] 00001000 bbbbbrbb OUT:PFC8 Note 10. Read and writes to these register may require synchronization delay, see the section “Synchronization Delay” in the EZ-USB TRM. Document Number: 38-08039 Rev. *J Page 31 of 72 [+] Feedback CY7C64713 Table 9. FX1 Register Summary (continued) Hex Size Name Description b7 b6 E635 1 EP6FIFOPFL[11] Endpoint 6 / IN:PKTS[1] IN:PKTS[0] slave FIFO OUT:PFC7 OUT:PFC6 Programmable Flag L E636 1 EP8FIFOPFH[11] E636 1 EP8FIFOPFH[11] Endpoint 8 / slave FIFO Programmable Flag H ISO Mode Endpoint 8 / slave FIFO Programmable Flag H Non-ISO Mode E637 1 EP8FIFOPFL[11] ISO Mode E637 1 EP8FIFOPFL[11] Non-ISO Mode E640 E641 E642 E643 E644 E648 8 1 1 1 1 4 1 reserved reserved reserved reserved reserved reserved INPKTEND[11] E649 7 OUTPKTEND[11] E650 1 INTERRUPTS EP2FIFOIE[13] Endpoint 2 slave FIFO Flag Interrupt Enable b4 b3 b2 b1 b0 Default Access PFC5 PFC4 PFC3 PFC2 PFC1 PFC0 00000000 RW DECIS PKTSTAT 0 IN: PKTS[1] IN: PKTS[0] OUT:PFC10 OUT:PFC9 0 0 PFC8 00001000 bbrbbrrb DECIS PKTSTAT 0 OUT:PFC10 OUT:PFC9 0 0 PFC8 00001000 bbrbbrrb Endpoint 8 / PFC7 PFC6 slave FIFO Programmable Flag L Endpoint 8 / IN: PKTS[1] IN: PKTS[0] slave FIFO OUT:PFC7 OUT:PFC6 Programmable Flag L Force IN Packet End Force OUT Packet End b5 PFC5 PFC4 PFC3 PFC2 PFC1 PFC0 00000000 RW PFC5 PFC4 PFC3 PFC2 PFC1 PFC0 00000000 RW Skip 0 0 0 EP3 EP2 EP1 EP0 xxxxxxxx W Skip 0 0 0 EP3 EP2 EP1 EP0 xxxxxxxx W 0 0 0 0 EDGEPF PF EF FF 00000000 RW Note 11. Read and writes to these register may require synchronization delay, see the section “Synchronization Delay” in the EZ-USB TRM. Document Number: 38-08039 Rev. *J Page 32 of 72 [+] Feedback CY7C64713 Table 9. FX1 Register Summary (continued) Hex Size Name E651 1 EP2FIFOIRQ[12, 13] E652 1 EP4FIFOIE[13] E653 1 EP4FIFOIRQ[12, 13] E654 1 EP6FIFOIE[13] E655 1 EP6FIFOIRQ[14, 15] E656 1 EP8FIFOIE[15] E657 1 EP8FIFOIRQ[12, 13] E658 1 IBNIE E659 1 IBNIRQ[12] E65A 1 NAKIE E65B 1 NAKIRQ[12] Description b7 b6 b5 b4 b3 b2 b1 b0 Default Access Endpoint 2 slave FIFO Flag Interrupt Request Endpoint 4 slave FIFO Flag Interrupt Enable Endpoint 4 slave FIFO Flag Interrupt Request Endpoint 6 slave FIFO Flag Interrupt Enable Endpoint 6 slave FIFO Flag Interrupt Request Endpoint 8 slave FIFO Flag Interrupt Enable Endpoint 8 slave FIFO Flag Interrupt Request IN-BULK-NA K Interrupt Enable IN-BULK-NA K interrupt Request Endpoint Ping-NAK / IBN Interrupt Enable Endpoint Ping-NAK / IBN Interrupt Request 0 0 0 0 0 PF EF FF 00000111 rrrrrbbb 0 0 0 0 EDGEPF PF EF FF 00000000 0 0 0 0 0 PF EF FF 00000111 rrrrrbbb 0 0 0 0 EDGEPF PF EF FF 00000000 0 0 0 0 0 PF EF FF 00000110 rrrrrbbb 0 0 0 0 EDGEPF PF EF FF 00000000 0 0 0 0 0 PF EF FF 00000110 rrrrrbbb 0 0 EP8 EP6 EP4 EP2 EP1 EP0 00000000 0 0 EP8 EP6 EP4 EP2 EP1 EP0 00xxxxxx rrbbbbbb EP8 EP6 EP4 EP2 EP1 EP0 0 IBN 00000000 EP8 EP6 EP4 EP2 EP1 EP0 0 IBN xxxxxx0x bbbbbbrb RW RW RW RW RW Notes 12. SFRs not part of the standard 8051 architecture. 13. Read and writes to these register may require synchronization delay, see the section “Synchronization Delay” in the EZ-USB TRM. Document Number: 38-08039 Rev. *J Page 33 of 72 [+] Feedback CY7C64713 Table 9. FX1 Register Summary (continued) Hex Size Name E65C 1 USBIE E65D 1 USBIRQ[14] E65E 1 EPIE E65F 1 EPIRQ[14] E660 1 GPIFIE[15] E661 1 GPIFIRQ[15] E662 1 USBERRIE E663 1 USBERRIRQ[14] E664 1 ERRCNTLIM E665 1 CLRERRCNT E666 1 INT2IVEC E667 1 INT4IVEC E668 1 INTSETUP E669 7 E670 1 reserved INPUT / OUTPUT PORTACFG Description b7 b6 b5 b4 b3 b2 b1 b0 USB Int Enables USB Interrupt Requests Endpoint Interrupt Enables Endpoint Interrupt Requests GPIF Interrupt Enable GPIF Interrupt Request USB Error Interrupt Enables USB Error Interrupt Requests USB Error counter and limit Clear Error Counter EC3:0 Interrupt 2 (USB) Autovector Interrupt 4 (slave FIFO & GPIF) Autovector Interrupt 2 & 4 setup 0 EP0ACK 0 URES SUSP SUTOK SOF SUDAV 00000000 0 EP0ACK 0 URES SUSP SUTOK SOF SUDAV 0xxxxxxx rbbbbbbb EP8 EP6 EP4 EP2 EP1OUT EP1IN EP0OUT EP0IN 00000000 RW EP8 EP6 EP4 EP2 EP1OUT EP1IN EP0OUT EP0IN 0 RW 0 0 0 0 0 0 GPIFWF GPIFDONE 00000000 RW 0 0 0 0 0 0 GPIFWF GPIFDONE 000000xx RW ISOEP8 ISOEP6 ISOEP4 ISOEP2 0 0 0 ERRLIMIT 00000000 RW ISOEP8 ISOEP6 ISOEP4 ISOEP2 0 0 0 ERRLIMIT 0000000x bbbbrrrb EC3 EC2 EC1 EC0 LIMIT3 LIMIT2 LIMIT1 LIMIT0 x x x x x x x x xxxxxxxx W 0 I2V4 I2V3 I2V2 I2V1 I2V0 0 0 00000000 R 1 0 I4V3 I4V2 I4V1 I4V0 0 0 10000000 R 0 0 0 0 AV2EN 0 INT4SRC AV4EN 00000000 RW FLAGD SLCS 0 0 0 0 INT1 INT0 00000000 RW I/O PORTA Alternate Configuration Default Access RW xxxx0100 rrrrbbbb Notes 14. SFRs not part of the standard 8051 architecture. 15. Read and writes to these register may require synchronization delay, see the section “Synchronization Delay” in the EZ-USB TRM. Document Number: 38-08039 Rev. *J Page 34 of 72 [+] Feedback CY7C64713 Table 9. FX1 Register Summary (continued) Hex Size Name E671 1 PORTCCFG E672 1 PORTECFG E673 4 XTALINSRC E677 E678 1 1 reserved I2CS E679 E67A 1 1 I2DAT I2CTL E67B 1 XAUTODAT1 E67C 1 XAUTODAT2 E67D 1 UDMA CRC UDMACRCH[16] E67E 1 E67F 1 E680 1 E681 1 E682 1 E683 1 E684 1 Description b7 b6 b5 b4 b3 b2 b1 b0 I/O PORTC Alternate Configuration I/O PORTE Alternate Configuration XTALIN Clock Source GPIFA7 GPIFA6 GPIFA5 GPIFA4 GPIFA3 GPIFA2 GPIFA1 GPIFA0 00000000 RW GPIFA8 T2EX INT6 RXD1OUT RXD0OUT T2OUT T1OUT T0OUT 00000000 RW 0 0 0 0 0 0 0 EXTCLK 00000000 rrrrrrrb I²C Bus Control & Status I²C Bus Data I²C Bus Control Autoptr1 MOVX access, when APTREN = 1 Autoptr2 MOVX access, when APTREN = 1 START STOP LASTRD ID1 ID0 BERR ACK DONE 000xx000 bbbrrrrr d7 0 d6 0 d5 0 d4 0 d3 0 d2 0 d1 STOPIE d0 400KHZ xxxxxxxx 00000000 RW RW D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW CRC15 CRC14 CRC13 CRC12 CRC11 CRC10 CRC9 CRC8 01001010 RW CRC7 CRC6 CRC5 CRC4 CRC3 CRC2 CRC1 CRC0 10111010 RW QENABLE 0 0 0 QSTATE QSIGNAL2 QSIGNAL1 QSIGNAL0 00000000 brrrbbbb 0 0 0 0 DISCON NOSYNSOF RENUM SIGRSUME x0000000 rrrrbbbb x x x x x x x x WU2 WU WU2POL WUPOL 0 DPEN WU2EN WUEN xx000101 bbbbrbbb Q S R I/O EP3 EP2 EP1 EP0 x0000000 rrrbbbbb 0 0 0 0 0 FC10 FC9 FC8 00000xxx UDMA CRC MSB UDMACRCL[16] UDMA CRC LSB UDMACRC-QUALIFIER UDMA CRC Qualifier USB CONTROL USBCS USB Control & Status SUSPEND Put chip into suspend WAKEUPCS Wakeup Control & Status TOGCTL Toggle Control USBFRAMEH USB Frame count H Default Access xxxxxxxx W R Note 16. Read and writes to these register may require synchronization delay, see the section “Synchronization Delay” in the EZ-USB TRM. Document Number: 38-08039 Rev. *J Page 35 of 72 [+] Feedback CY7C64713 Table 9. FX1 Register Summary (continued) Hex Size Name E685 1 USBFRAMEL E686 E687 1 1 reserved FNADDR E688 2 E68A 1 reserved ENDPOINTS EP0BCH[17] E68B 1 EP0BCL[17] E68C E68D 1 1 reserved EP1OUTBC E68E E68F 1 1 reserved EP1INBC E690 1 EP2BCH[17] E691 1 EP2BCL[17] E692 E694 2 1 reserved EP4BCH[17] E695 1 EP4BCL[17] E696 E698 2 1 reserved EP6BCH[17] E699 1 EP6BCL[17] E69A E69C 2 1 reserved EP8BCH[17] E69D 1 EP8BCL[17] E69E 2 reserved Description b7 b6 b5 b4 b3 b2 b1 b0 FC7 FC6 FC5 FC4 FC3 FC2 FC1 FC0 xxxxxxxx R USB Function address 0 FA6 FA5 FA4 FA3 FA2 FA1 FA0 0xxxxxxx R Endpoint 0 Byte Count H Endpoint 0 Byte Count L (BC15) (BC14) (BC13) (BC12) (BC11) (BC10) (BC9) (BC8) xxxxxxxx RW (BC7) BC6 BC5 BC4 BC3 BC2 BC1 BC0 xxxxxxxx RW Endpoint 1 OUT Byte Count 0 BC6 BC5 BC4 BC3 BC2 BC1 BC0 xxxxxxxx RW Endpoint 1 IN Byte Count Endpoint 2 Byte Count H Endpoint 2 Byte Count L 0 BC6 BC5 BC4 BC3 BC2 BC1 BC0 xxxxxxxx RW 0 0 0 0 0 BC10 BC9 BC8 xxxxxxxx RW BC7/SKIP BC6 BC5 BC4 BC3 BC2 BC1 BC0 xxxxxxxx RW 0 0 0 0 0 0 BC9 BC8 xxxxxxxx RW BC7/SKIP BC6 BC5 BC4 BC3 BC2 BC1 BC0 xxxxxxxx RW 0 0 0 0 0 BC10 BC9 BC8 xxxxxxxx RW BC7/SKIP BC6 BC5 BC4 BC3 BC2 BC1 BC0 xxxxxxxx RW 0 0 0 0 0 0 BC9 BC8 xxxxxxxx RW BC7/SKIP BC6 BC5 BC4 BC3 BC2 BC1 BC0 xxxxxxxx RW USB Frame count L Endpoint 4 Byte Count H Endpoint 4 Byte Count L Endpoint 6 Byte Count H Endpoint 6 Byte Count L Endpoint 8 Byte Count H Endpoint 8 Byte Count L Default Access Note 17. Read and writes to these register may require synchronization delay, see the section “Synchronization Delay” in the EZ-USB TRM. Document Number: 38-08039 Rev. *J Page 36 of 72 [+] Feedback CY7C64713 Table 9. FX1 Register Summary (continued) Hex Size Name E6A0 1 EP0CS E6A1 1 EP1OUTCS E6A2 1 EP1INCS E6A3 1 EP2CS E6A4 1 EP4CS E6A5 1 EP6CS E6A6 1 EP8CS E6A7 1 EP2FIFOFLGS E6A8 1 EP4FIFOFLGS E6A9 1 EP6FIFOFLGS E6AA 1 EP8FIFOFLGS E6AB 1 EP2FIFOBCH E6AC 1 EP2FIFOBCL E6AD 1 EP4FIFOBCH Description b7 b6 b5 b4 b3 b2 b1 b0 Default Access Endpoint 0 Control and Status Endpoint 1 OUT Control and Status Endpoint 1 IN Control and Status Endpoint 2 Control and Status Endpoint 4 Control and Status Endpoint 6 Control and Status Endpoint 8 Control and Status Endpoint 2 slave FIFO Flags Endpoint 4 slave FIFO Flags Endpoint 6 slave FIFO Flags Endpoint 8 slave FIFO Flags Endpoint 2 slave FIFO total byte count H Endpoint 2 slave FIFO total byte count L Endpoint 4 slave FIFO total byte count H HSNAK 0 0 0 0 0 BUSY STALL 10000000 bbbbbbrb 0 0 0 0 0 0 BUSY STALL 00000000 bbbbbbrb 0 0 0 0 0 0 BUSY STALL 00000000 bbbbbbrb 0 NPAK2 NPAK1 NPAK0 FULL EMPTY 0 STALL 00101000 rrrrrrrb 0 0 NPAK1 NPAK0 FULL EMPTY 0 STALL 00101000 rrrrrrrb 0 NPAK2 NPAK1 NPAK0 FULL EMPTY 0 STALL 00000100 rrrrrrrb 0 0 NPAK1 NPAK0 FULL EMPTY 0 STALL 00000100 rrrrrrrb 0 0 0 0 0 PF EF FF 00000010 R 0 0 0 0 0 PF EF FF 00000010 R 0 0 0 0 0 PF EF FF 00000110 R 0 0 0 0 0 PF EF FF 00000110 R 0 0 0 BC12 BC11 BC10 BC9 BC8 00000000 R BC7 BC6 BC5 BC4 BC3 BC2 BC1 BC0 00000000 R 0 0 0 0 0 BC10 BC9 BC8 00000000 R Document Number: 38-08039 Rev. *J Page 37 of 72 [+] Feedback CY7C64713 Table 9. FX1 Register Summary (continued) Hex Size Name E6AE 1 EP4FIFOBCL E6AF 1 EP6FIFOBCH E6B0 1 EP6FIFOBCL E6B1 1 EP8FIFOBCH E6B2 1 EP8FIFOBCL E6B3 1 SUDPTRH E6B4 1 SUDPTRL E6B5 1 SUDPTRCTL E6B8 2 8 reserved SETUPDAT Description b7 b6 b5 b4 b3 b2 b1 b0 Endpoint 4 slave FIFO total byte count L Endpoint 6 slave FIFO total byte count H Endpoint 6 slave FIFO total byte count L Endpoint 8 slave FIFO total byte count H Endpoint 8 slave FIFO total byte count L Setup Data Pointer high address byte Setup Data Pointer low address byte Setup Data Pointer Auto Mode BC7 BC6 BC5 BC4 BC3 BC2 BC1 BC0 00000000 R 0 0 0 0 BC11 BC10 BC9 BC8 00000000 R BC7 BC6 BC5 BC4 BC3 BC2 BC1 BC0 00000000 R 0 0 0 0 0 BC10 BC9 BC8 00000000 R BC7 BC6 BC5 BC4 BC3 BC2 BC1 BC0 00000000 R A15 A14 A13 A12 A11 A10 A9 A8 xxxxxxxx RW A7 A6 A5 A4 A3 A2 A1 0 0 0 0 0 0 0 0 D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx R FIFOWR0 FIFORD1 FIFORD0 11100100 RW 8 bytes of setup data Default Access xxxxxxx0 bbbbbbbr SDPAUTO 00000001 RW SETUPDAT[0] = bmRequestTy pe SETUPDAT[1] = bmRequest SETUPDAT[2: 3] = wValue SETUPDAT[4: 5] = wIndex SETUPDAT[6: 7] = wLength E6C0 1 GPIF GPIFWFSELECT Waveform Selector Document Number: 38-08039 Rev. *J SINGLEWR1 SINGLEWR0 SINGLERD1 SINGLERD0 FIFOWR1 Page 38 of 72 [+] Feedback CY7C64713 Table 9. FX1 Register Summary (continued) Hex Size Name E6C1 1 GPIFIDLECS E6C2 1 GPIFIDLECTL E6C3 1 GPIFCTLCFG E6C4 1 GPIFADRH[18] E6C5 1 GPIFADRL[18] E6C6 1 FLOWSTATE FLOWSTATE E6C7 1 FLOWLOGIC E6C8 1 FLOWEQ0CTL E6C9 1 FLOWEQ1CTL E6CA 1 FLOWHOLDOFF E6CB 1 FLOWSTB E6CC 1 FLOWSTBEDGE E6CD 1 FLOWSTBPERIOD E6CE 1 GPIFTCB3[18] E6CF 1 GPIFTCB2[18] Description b7 b6 b5 b4 b3 b2 b1 b0 GPIF Done, GPIF IDLE drive mode Inactive Bus, CTL states CTL Drive Type GPIF Address H GPIF Address L DONE 0 0 0 0 0 0 IDLEDRV 10000000 RW 0 0 CTL5 CTL4 CTL3 CTL2 CTL1 CTL0 11111111 RW TRICTL 0 CTL5 CTL4 CTL3 CTL2 CTL1 CTL0 00000000 RW 0 0 0 0 0 0 0 GPIFA8 00000000 RW GPIFA7 GPIFA6 GPIFA5 GPIFA4 GPIFA3 GPIFA2 GPIFA1 GPIFA0 00000000 RW FS2 FS1 FS0 TERMB2 TERMB1 TERMB0 00000000 RW CTL2 CTL1 CTL0 00000000 RW CTL2 CTL1 CTL0 00000000 RW HOCTL2 HOCTL1 HOCTL0 00000000 RW MSTB2 MSTB1 MSTB0 00100000 RW 0 FALLING RISING 00000001 rrrrrrbb D2 D1 D0 00000010 RW Flowstate FSE 0 0 0 0 Enable and Selector Flowstate LFUNC1 LFUNC0 TERMA2 TERMA1 TERMA0 Logic CTL-Pin CTL0E3 CTL0E2 CTL0E1/CTL5 CTL0E0/CTL4 CTL3 States in Flowstate (when Logic = 0) CTL-Pin CTL0E3 CTL0E2 CTL0E1/CTL5 CTL0E0/CTL4 CTL3 States in Flowstate (when Logic = 1) HOPERIOD3 HOPERIOD2 HOPERIOD1 HOPERIOD0 HOSTATE Holdoff Configuration Flowstate SLAVE RDYASYNC CTLTOGL SUSTAIN 0 Strobe Configuration Flowstate 0 0 0 0 0 Rising/Falling Edge Configuration Master-Strobe D7 D6 D5 D4 D3 Half-Period GPIF Transaction Count Byte 3 GPIF Transaction Count Byte 2 Default Access 00000000 brrrrbbb TC31 TC30 TC29 TC28 TC27 TC26 TC25 TC24 00000000 RW TC23 TC22 TC21 TC20 TC19 TC18 TC17 TC16 00000000 RW Note 18. Read and writes to these register may require synchronization delay, see the section “Synchronization Delay” in the EZ-USB TRM. Document Number: 38-08039 Rev. *J Page 39 of 72 [+] Feedback CY7C64713 Table 9. FX1 Register Summary (continued) Hex Size Name E6D0 1 GPIFTCB1[19] E6D1 1 GPIFTCB0[19] 2 E6D2 1 reserved reserved reserved EP2GPIFFLGSEL[19] E6D3 1 EP2GPIFPFSTOP E6D4 1 EP2GPIFTRIG[19] 3 E6DA 1 reserved reserved reserved EP4GPIFFLGSEL[19] E6DB 1 EP4GPIFPFSTOP E6DC 1 EP4GPIFTRIG[19] 3 E6E2 1 reserved reserved reserved EP6GPIFFLGSEL[19] E6E3 1 EP6GPIFPFSTOP E6E4 1 EP6GPIFTRIG[19] Description b7 b6 b5 b4 b3 b2 b1 b0 GPIF Transaction Count Byte 1 GPIF Transaction Count Byte 0 TC15 TC14 TC13 TC12 TC11 TC10 TC9 TC8 00000000 RW TC7 TC6 TC5 TC4 TC3 TC2 TC1 TC0 00000001 RW 00000000 RW 00000000 RW FIFO2FLAG 00000000 RW FS0 Default Access Endpoint 2 GPIF Flag select Endpoint 2 GPIF stop transaction on prog. flag Endpoint 2 GPIF Trigger 0 0 0 0 0 0 FS1 0 0 0 0 0 0 0 x x x x x x x x xxxxxxxx W Endpoint 4 GPIF Flag select Endpoint 4 GPIF stop transaction on GPIF Flag Endpoint 4 GPIF Trigger 0 0 0 0 0 0 FS1 FS0 00000000 RW 0 0 0 0 0 0 0 FIFO4FLAG 00000000 RW x x x x x x x x xxxxxxxx W Endpoint 6 GPIF Flag select Endpoint 6 GPIF stop transaction on prog. flag Endpoint 6 GPIF Trigger 0 0 0 0 0 0 FS1 FS0 00000000 RW 0 0 0 0 0 0 0 FIFO6FLAG 00000000 RW x x x x x x x x xxxxxxxx W Note 19. Read and writes to these register may require synchronization delay, see the section “Synchronization Delay” in the EZ-USB TRM. Document Number: 38-08039 Rev. *J Page 40 of 72 [+] Feedback CY7C64713 Table 9. FX1 Register Summary (continued) Hex Size 3 Name E6EA 1 reserved reserved reserved EP8GPIFFLGSEL[20] E6EB 1 EP8GPIFPFSTOP E6EC 1 EP8GPIFTRIG[20] E6F0 3 1 reserved XGPIFSGLDATH E6F1 1 XGPIFSGLDATLX E6F2 1 XGPIFSGLDATLNOX E6F3 1 GPIFREADYCFG E6F4 1 GPIFREADYSTAT E6F5 1 GPIFABORT E6F6 2 E740 reserved ENDPOINT BUFFERS 64 EP0BUF E780 64 EP10UTBUF E7C0 64 EP1INBUF 2048 reserved Description b7 b6 b5 b4 b3 b2 b1 b0 Default Access Endpoint 8 GPIF Flag select Endpoint 8 GPIF stop transaction on prog. flag Endpoint 8 GPIF Trigger 0 0 0 0 0 0 FS1 FS0 0 0 0 0 0 0 0 x x x x x x x x xxxxxxxx W GPIF Data H (16-bit mode only) Read/Write GPIF Data L & trigger transaction Read GPIF Data L, no transaction trigger Internal RDY, Sync/Async, RDY pin states D15 D14 D13 D12 D11 D10 D9 D8 xxxxxxxx RW D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx R INTRDY SAS TCXRDY5 0 0 0 0 0 GPIF Ready Status Abort GPIF Waveforms 0 0 RDY5 RDY4 RDY3 RDY2 RDY1 RDY0 00xxxxxx R x x x x x x x x xxxxxxxx W EP0-IN/-OUT buffer EP1-OUT buffer EP1-IN buffer D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW RW 00000000 RW FIFO8FLAG 00000000 RW 00000000 bbbrrrrr Note 20. Read and writes to these register may require synchronization delay, see the section “Synchronization Delay” in the EZ-USB TRM. Document Number: 38-08039 Rev. *J Page 41 of 72 [+] Feedback CY7C64713 Table 9. FX1 Register Summary (continued) Hex Size Name F000 1023 EP2FIFOBUF F400 64 EP4FIFOBUF F600 64 reserved F800 1023 EP6FIFOBUF FC00 64 EP8FIFOBUF FE00 xxxx Description b7 b6 b5 b4 b3 b2 b1 b0 Default Access 64/1023-byte EP 2 / slave FIFO buffer (IN or OUT) 64 byte EP 4 / slave FIFO buffer (IN or OUT) D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW 64/1023-byte EP 6 / slave FIFO buffer (IN or OUT) 64 byte EP 8 / slave FIFO buffer (IN or OUT) D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW 0 DISCON 0 0 0 0 0 400KHZ xxxxxxxx[22] n/a D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW D7 A7 D6 A6 D5 A5 D4 A4 D3 A3 D2 A2 D1 A1 D0 A0 00000111 00000000 RW RW A15 A14 A13 A12 A11 A10 A9 A8 00000000 RW A7 A6 A5 A4 A3 A2 A1 A0 00000000 RW A15 A14 A13 A12 A11 A10 A9 A8 00000000 RW 0 0 0 0 0 0 0 SEL 00000000 RW SMOD0 TF1 x TR1 1 TF0 1 TR0 x IE1 x IT1 x IE0 IDLE IT0 00110000 00000000 RW RW GATE CT M1 M0 GATE CT M1 M0 00000000 RW D7 D6 D5 D4 D3 D2 D1 D0 00000000 RW 87 88 64 reserved I²C Configuration Byte Special Function Registers (SFRs) 1 IOA[21] Port A (bit addressable) 1 SP Stack Pointer 1 DPL0 Data Pointer 0 L 1 DPH0 Data Pointer 0 H 1 DPL1[21] Data Pointer 1 L 1 DPH1[21] Data Pointer 1 H 1 DPS[21] Data Pointer 0/1 select 1 PCON Power Control Timer/Counter 1 TCON 89 1 TMOD 8A 1 TL0 80 81 82 83 84 85 86 Control (bit addressable) Timer/Counter Mode Control Timer 0 reload L Notes 21. SFRs not part of the standard 8051 architecture. 22. If no EEPROM is detected by the SIE then the default is 00000000. Document Number: 38-08039 Rev. *J Page 42 of 72 [+] Feedback CY7C64713 Table 9. FX1 Register Summary (continued) Hex Size Name 8B 1 TL1 8C 1 TH0 8D 1 TH1 8E 8F 90 1 1 1 CKCON[23] reserved IOB[23] 91 1 EXIF[23] 92 1 MPAGE[23] 93 98 5 1 reserved SCON0 99 1 SBUF0 9A 1 AUTOPTRH1[23] 9B 1 AUTOPTRL1[23] 9C 9D 1 1 reserved AUTOPTRH2[23] 9E 1 AUTOPTRL2[23] 9F A0 1 1 reserved IOC[23] A1 1 INT2CLR[23] A2 1 INT4CLR[23] A3 5 reserved Description b7 b6 b5 b4 b3 b2 b1 b0 Timer 1 reload L Timer 0 reload H Timer 1 reload H Clock Control D7 D6 D5 D4 D3 D2 D1 D0 00000000 RW D15 D14 D13 D12 D11 D10 D9 D8 00000000 RW D15 D14 D13 D12 D11 D10 D9 D8 00000000 RW x x T2M T1M T0M MD2 MD1 MD0 00000001 RW D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW IE5 IE4 I²CINT USBNT 1 0 0 0 00001000 RW A15 A14 A13 A12 A11 A10 A9 A8 00000000 RW Serial Port 0 Control (bit addressable) Serial Port 0 Data Buffer Autopointer 1 Address H Autopointer 1 Address L SM0_0 SM1_0 SM2_0 REN_0 TB8_0 RB8_0 TI_0 RI_0 00000000 RW D7 D6 D5 D4 D3 D2 D1 D0 00000000 RW A15 A14 A13 A12 A11 A10 A9 A8 00000000 RW A7 A6 A5 A4 A3 A2 A1 A0 00000000 RW Autopointer 2 Address H Autopointer 2 Address L A15 A14 A13 A12 A11 A10 A9 A8 00000000 RW A7 A6 A5 A4 A3 A2 A1 A0 00000000 RW Port C (bit addressable) Interrupt 2 clear Interrupt 4 clear D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW x x x x x x x x xxxxxxxx W x x x x x x x x xxxxxxxx W Port B (bit addressable) External Interrupt Flag(s) Upper Addr Byte of MOVX using @R0 / @R1 Default Access Note 23. SFRs not part of the standard 8051 architecture. Document Number: 38-08039 Rev. *J Page 43 of 72 [+] Feedback CY7C64713 Table 9. FX1 Register Summary (continued) Hex Size Name A8 1 IE A9 AA 1 1 reserved EP2468STAT[24] AB 1 EP24FIFOFLGS[24] AC 1 EP68FIFOFLGS[24] AD AF 2 1 reserved AUTOPTRSETUP[24] B0 1 IOD[23] B1 1 IOE[24] B2 1 OEA[24] B3 1 OEB[24] B4 1 OEC[24] B5 1 OED[24] B6 1 OEE[24] B7 B8 1 1 reserved IP B9 BA 1 1 reserved EP01STAT[24] BB 1 GPIFTRIG[24, 25] Description b7 b6 b5 b4 b3 b2 b1 b0 Interrupt Enable (bit addressable) EA ES1 ET2 ES0 ET1 EX1 ET0 EX0 00000000 RW Endpoint 2, 4, 6, 8 status flags Endpoint 2, 4 slave FIFO status flags Endpoint 6, 8 slave FIFO status flags EP8F EP8E EP6F EP6E EP4F EP4E EP2F EP2E 01011010 R 0 EP4PF EP4EF EP4FF 0 EP2PF EP2EF EP2FF 00100010 R 0 EP8PF EP8EF EP8FF 0 EP6PF EP6EF EP6FF 01100110 R Autopointer 1&2 setup Port D (bit addressable) Port E (NOT bit addressable) Port A Output Enable Port B Output Enable Port C Output Enable Port D Output Enable Port E Output Enable 0 0 0 0 0 APTR2INC APTR1INC APTREN 00000110 RW D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW D7 D6 D5 D4 D3 D2 D1 D0 00000000 RW D7 D6 D5 D4 D3 D2 D1 D0 00000000 RW D7 D6 D5 D4 D3 D2 D1 D0 00000000 RW D7 D6 D5 D4 D3 D2 D1 D0 00000000 RW D7 D6 D5 D4 D3 D2 D1 D0 00000000 RW Interrupt Priority (bit addressable) 1 PS1 PT2 PS0 PT1 PX1 PT0 PX0 10000000 RW Endpoint 0&1 Status Endpoint 2, 4, 6, 8 GPIF slave FIFO Trigger 0 0 0 0 0 EP0BSY 00000000 R DONE 0 0 0 0 EP1INBSY EP1OUTBSY RW EP1 EP0 Default Access 10000xxx brrrrbbb Notes 24. SFRs not part of the standard 8051 architecture. 25. Read and writes to these register may require synchronization delay, see the section “Synchronization Delay” in the EZ-USB TRM. Document Number: 38-08039 Rev. *J Page 44 of 72 [+] Feedback CY7C64713 Table 9. FX1 Register Summary (continued) Hex Size Description b7 b6 b5 b4 b3 b2 b1 b0 Default Access D15 D14 D13 D12 D11 D10 D9 D8 xxxxxxxx RW D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx R SM0_1 SM1_1 SM2_1 REN_1 TB8_1 RB8_1 TI_1 RI_1 00000000 RW D7 D6 D5 D4 D3 D2 D1 D0 00000000 RW 6 1 GPIF Data H (16-bit mode only) GPIFSGLDATLX[26] GPIF Data L w/ Trigger GPIFSGLDATLNOX[26] GPIF Data L w/ No Trigger SCON1[26] Serial Port 1 Control (bit addressable) SBUF1[26] Serial Port 1 Data Buffer reserved Timer/Counter T2CON TF2 EXF2 RCLK TCLK EXEN2 TR2 CT2 CPRL2 00000000 RW C9 CA 1 1 reserved RCAP2L D7 D6 D5 D4 D3 D2 D1 D0 00000000 RW CB 1 RCAP2H D7 D6 D5 D4 D3 D2 D1 D0 00000000 RW CC 1 TL2 D7 D6 D5 D4 D3 D2 D1 D0 00000000 RW CD 1 TH2 D15 D14 D13 D12 D11 D10 D9 D8 00000000 RW CE D0 2 1 reserved PSW CY AC F0 RS1 RS0 OV F1 P 00000000 RW D1 D8 7 1 reserved EICON[26] SMOD1 1 ERESI RESI INT6 0 0 0 01000000 RW D9 E0 7 1 reserved ACC D7 D6 D5 D4 D3 D2 D1 D0 00000000 RW BC BD 1 1 BE 1 BF 1 C0 1 C1 1 C2 C8 Name reserved GPIFSGLDATH[26] 2 Control (bit addressable) Capture for Timer 2, auto-reload, up-counter Capture for Timer 2, auto-reload, up-counter Timer 2 reload L Timer 2 reload H Program Status Word (bit addressable) External Interrupt Control Accumulator (bit addressable) Note 26. SFRs not part of the standard 8051 architecture. Document Number: 38-08039 Rev. *J Page 45 of 72 [+] Feedback CY7C64713 Table 9. FX1 Register Summary (continued) Hex Size Name E1 E8 7 1 reserved EIE[27] E9 F0 7 1 reserved B F1 F8 7 1 reserved EIP[27] Description External Interrupt Enable(s) B (bit addressable) External Interrupt Priority Control b7 b6 b5 b4 b3 b2 b1 b0 Default Access 1 1 1 EX6 EX5 EX4 EI²C EUSB 11100000 RW D7 D6 D5 D4 D3 D2 D1 D0 00000000 RW 1 1 1 PX6 PX5 PX4 PI²C PUSB 11100000 RW F9 7 reserved Legend (For the Access column) R = all bits read-only W = all bits write-only r = read-only bit w = write-only bit b = both read/write bit Note 27. SFRs not part of the standard 8051 architecture. Document Number: 38-08039 Rev. *J Page 46 of 72 [+] Feedback CY7C64713 Absolute Maximum Ratings Exceeding maximum ratings may shorten the useful life of the device. User guidelines are not tested. Storage Temperature ................................ –65 °C to +150 °C Ambient Temperature with Power Supplied.... 0 °C to +70 °C Supply Voltage to Ground Potential..............–0.5 V to +4.0 V Max Output Current, per I/O port................................ 10 mA Max Output Current, all five I/O ports (128 and 100 pin packages) ....................................... 50 mA Operating Conditions DC Input Voltage to Any Input Pin ......................... 5.25 V[28] TA (Ambient Temperature Under Bias) ........... 0 °C to +70 °C DC Voltage Applied to Outputs in High Z State ................................... –0.5 V to VCC + 0.5 V Supply Voltage..........................................+3.15 V to +3.45 V Power Dissipation.................................................... 235 mW FOSC (Oscillator or Crystal Frequency).... 24 MHz ± 100 ppm Parallel Resonant Static Discharge Voltage......................................... > 2000 V Ground Voltage................................................................. 0 V DC Characteristics Parameter VCC Description Conditions Supply Voltage Min Typ Max Unit 3.15 3.3 3.45 V 200 – – s VIH Input HIGH Voltage 2 – 5.25 V VIL Input LOW Voltage –0.5 – 0.8 V VIH_X Crystal input HIGH Voltage 2 – 5.25 V VIL_X Crystal input LOW Voltage –0.05 – 0.8 V II Input Leakage Current – – ±10 A VOH Output Voltage HIGH IOUT = 4 mA 2.4 – – V VOL Output LOW Voltage IOUT = –4 mA – – 0.4 V VCC Ramp Up 0 to 3.3 V 0 < VIN < VCC IOH Output Current HIGH – – 4 mA IOL Output Current LOW – – 4 mA CIN Input Pin Capacitance ISUSP Suspend Current Except D+/D– – 3.29 10 pF D+/D– – 12.96 15 pF Connected – 0.5 1.2 mA Disconnected – 0.3 1.0 mA ICC Supply Current 8051 running, connected to USB TRESET Reset Time after Valid Power VCC min = 3.0 V Pin Reset after powered on – 35 65 mA 5.0 – – ms 200 – – s USB Transceiver USB 2.0 compliant in full speed mode. Note 28. It is recommended to not power I/O when chip power is off. Document Number: 38-08039 Rev. *J Page 47 of 72 [+] Feedback CY7C64713 AC Electrical Characteristics USB Transceiver USB 2.0 compliant in full speed mode. Figure 12. Program Memory Read Timing Diagram tCL CLKOUT[29] tAV tAV A[15..0] tSTBH tSTBL PSEN# [30] tACC1 D[7..0] tDH data in tSOEL OE# tSCSL CS# Table 10. Program Memory Read Parameters Parameter tCL Description 1/CLKOUT Frequency Min Typ Max Unit Notes – 20.83 – ns 48 MHz – 41.66 – ns 24 MHz – 83.2 – ns 12 MHz tAV Delay from Clock to Valid Address 0 – 10.7 ns tSTBL Clock to PSEN Low 0 – 8 ns tSTBH Clock to PSEN High 0 – 8 ns tSOEL Clock to OE Low – – 11.1 ns tSCSL Clock to CS Low tDSU Data Setup to Clock tDH Data Hold Time – – 13 ns 9.6 – – ns 0 – – ns Notes 29. CLKOUT is shown with positive polarity. 30. tACC1 is computed from the parameters in Table 10 as follows: tACC1(24 MHz) = 3 × tCL – tAV – tDSU = 106 ns tACC1(48 MHz) = 3 × tCL – tAV – tDSU = 43 ns. Document Number: 38-08039 Rev. *J Page 48 of 72 [+] Feedback CY7C64713 Figure 13. Data Memory Read Timing Diagram tCL Stretch = 0 CLKOUT[31] tAV tAV A[15..0] tSTBH tSTBL RD# tSCSL CS# tSOEL OE# tDSU [32] tDH tACC1 D[7..0] data in tCL Stretch = 1 CLKOUT[31] tAV A[15..0] RD# CS# tDSU tACC1[32] D[7..0] tDH data in Table 11. Data Memory Read Parameters Parameter tCL Description 1/CLKOUT Frequency Min Typ Max Unit Notes – 20.83 – ns 48 MHz – 41.66 – ns 24 MHz – 83.2 – ns 12 MHz tAV Delay from Clock to Valid Address – – 10.7 ns tSTBL Clock to RD LOW – – 11 ns tSTBH Clock to RD HIGH – – 11 ns tSCSL Clock to CS LOW – – 13 ns tSOEL Clock to OE LOW tDSU Data Setup to Clock tDH Data Hold Time – – 11.1 ns 9.6 – – ns 0 – – ns When using the AUTPOPTR1 or AUTOPTR2 to address external memory, the address of AUTOPTR1 is active only when either RD# or WR# are active. The address of AUTOPTR2 is active throughout the cycle and meets the above address valid time for which is based on the stretch value. Notes 31. CLKOUT is shown with positive polarity. 32. tACC2 and tACC3 are computed from the parameters in Table 11 as follows: tACC2(24 MHz) = 3 × tCL – tAV – tDSU = 106 ns tACC2(48 MHz) = 3 × tCL – tAV – tDSU = 43 ns tACC3(24 MHz) = 5 × tCL – tAV – tDSU = 190 ns tACC3(48 MHz) = 5 × tCL – tAV – tDSU = 86 ns. Document Number: 38-08039 Rev. *J Page 49 of 72 [+] Feedback CY7C64713 Figure 14. Data Memory Write Timing Diagram tCL CLKOUT tAV tSTBL tSTBH tAV A[15..0] WR# tSCSL CS# tON1 tOFF1 data out D[7..0] Stretch = 1 tCL CLKOUT tAV A[15..0] WR# CS# tON1 tOFF1 data out D[7..0] Table 12. Data Memory Write Parameters Min Max Unit tAV Parameter Delay from Clock to Valid Address Description 0 10.7 ns tSTBL Clock to WR Pulse LOW 0 11.2 ns tSTBH Clock to WR Pulse HIGH 0 11.2 ns tSCSL Clock to CS Pulse LOW – 13.0 ns tON1 Clock to Data Turn-on 0 13.1 ns tOFF1 Clock to Data Hold Time 0 13.1 ns Notes When using the AUTPOPTR1 or AUTOPTR2 to address external memory, the address of AUTOPTR1 is active only when either RD# or WR# are active. The address of AUTOPTR2 is active throughout the cycle and meets the above address valid time for which is based on the stretch value. Document Number: 38-08039 Rev. *J Page 50 of 72 [+] Feedback CY7C64713 PORTC Strobe Feature Timings The RD# and WR# are present in the 100 pin version and the 128 pin package. In these 100 pin and 128 pin versions, an 8051 control bit is set to pulse the RD# and WR# pins when the 8051 reads from or writes to the PORTC. This feature is enabled by setting the PORTCSTB bit in CPUCS register. The RD# and WR# strobes are asserted for two CLKOUT cycles when the PORTC is accessed. The WR# strobe is asserted two clock cycles after the PORTC is updated and is active for two clock cycles after that as shown in Figure 16. As for read, the value of the PORTC three clock cycles before the assertion of RD# is the value that the 8051 reads in. The RD# is pulsed for 2 clock cycles after 3 clock cycles from the point when the 8051 has performed a read function on PORTC. In this feature the RD# signal prompts the external logic to prepare the next data byte. Nothing gets sampled internally on assertion of the RD# signal itself. It is just a “prefetch” type signal to get the next data byte prepared. Therefore, using it meets the set up time to the next read. The purpose of this pulsing of RD# is to let the external peripheral know that the 8051 is done reading PORTC and that the data was latched into the PORTC three CLKOUT cycles prior to asserting the RD# signal. After the RD# is pulsed the external logic may update the data on PORTC. The timing diagram of the read and write strobing function on accessing PORTC follows. Refer to Figure 13 on page 49 and Figure 14 on page 50 for details on propagation delay of RD# and WR# signals. Figure 16. WR# Strobe Function when PORTC is Accessed by 8051 tCLKOUT CLKOUT PORTC IS UPDATED tSTBL tSTBH WR# Figure 17. RD# Strobe Function when PORTC is Accessed by 8051 tCLKOUT CLKOUT 8051 READS PORTC DATA IS UPDATED BY EXTERNAL LOGIC DATA MUST BE HELD FOR 3 CLK CYLCES tSTBL tSTBH RD# Document Number: 38-08039 Rev. *J Page 51 of 72 [+] Feedback CY7C64713 GPIF Synchronous Signals In the following figure, dashed lines indicate signals with programmable polarity. Figure 18. GPIF Synchronous Signals Timing Diagram tIFCLK IFCLK tSGA GPIFADR[8:0] RDYX tSRY tRYH DATA(input) valid tSGD tDAH CTLX tXCTL DATA(output) N N+1 tXGD The following table provides the GPIF Synchronous Signals Parameters with Internally Sourced IFCLK. [33, 34] Table 13. GPIF Synchronous Signals Parameters with Internally Sourced IFCLK Parameter Description Min Max Unit 20.83 – ns 8.9 – ns 0 – ns 9.2 – ns tIFCLK IFCLK Period tSRY RDYX to Clock Setup Time tRYH Clock to RDYX tSGD GPIF Data to Clock Setup Time tDAH GPIF Data Hold Time 0 – ns tSGA Clock to GPIF Address Propagation Delay – 7.5 ns tXGD Clock to GPIF Data Output Propagation Delay – 11 ns tXCTL Clock to CTLX Output Propagation Delay – 6.7 ns Min Max Unit 20.83 200 ns The following table provides the GPIF Synchronous Signals Parameters with Externally Sourced IFCLK.[34] Table 14. GPIF Synchronous Signals Parameters with Externally Sourced IFCLK Parameter Description tIFCLK IFCLK Period tSRY RDYX to Clock Setup Time 2.9 – ns tRYH Clock to RDYX 3.7 – ns tSGD GPIF Data to Clock Setup Time 3.2 – ns tDAH GPIF Data Hold Time 4.5 – ns tSGA Clock to GPIF Address Propagation Delay – 11.5 ns tXGD Clock to GPIF Data Output Propagation Delay – 15 ns tXCTL Clock to CTLX Output Propagation Delay – 10.7 ns Notes 33. GPIF asynchronous RDYx signals have a minimum Setup time of 50 ns when using internal 48-MHz IFCLK. 34. IFCLK must not exceed 48 MHz. Document Number: 38-08039 Rev. *J Page 52 of 72 [+] Feedback CY7C64713 Slave FIFO Synchronous Read In the following figure, dashed lines indicate signals with programmable polarity. Figure 19. Slave FIFO Synchronous Read Timing Diagram tIFCLK IFCLK tSRD tRDH SLRD tXFLG FLAGS DATA N tOEon N+1 tXFD tOEoff SLOE The following table provides the Slave FIFO Synchronous Read Parameters with Internally Sourced IFCLK. [35] Table 15. Slave FIFO Synchronous Read Parameters with Internally Sourced IFCLK Min Max Unit tIFCLK Parameter IFCLK Period Description 20.83 – ns tSRD SLRD to Clock Setup Time 18.7 – ns tRDH Clock to SLRD Hold Time 0 – ns tOEon SLOE Turn on to FIFO Data Valid – 10.5 ns tOEoff SLOE Turn off to FIFO Data Hold – 10.5 ns tXFLG Clock to FLAGS Output Propagation Delay – 9.5 ns tXFD Clock to FIFO Data Output Propagation Delay – 11 ns The following table provides the Slave FIFO Synchronous Read Parameters with Externally Sourced IFCLK.[35] Table 16. Slave FIFO Synchronous Read Parameters with Externally Sourced IFCLK Parameter Description Min Max Unit tIFCLK IFCLK Period 20.83 200 ns tSRD SLRD to Clock Setup Time 12.7 – ns tRDH Clock to SLRD Hold Time 3.7 – ns tOEon SLOE Turn on to FIFO Data Valid – 10.5 ns tOEoff SLOE Turn off to FIFO Data Hold – 10.5 ns tXFLG Clock to FLAGS Output Propagation Delay – 13.5 ns tXFD Clock to FIFO Data Output Propagation Delay – 15 ns Note 35. IFCLK must not exceed 48 MHz. Document Number: 38-08039 Rev. *J Page 53 of 72 [+] Feedback CY7C64713 Slave FIFO Asynchronous Read In the following figure, dashed lines indicate signals with programmable polarity. Figure 20. Slave FIFO Asynchronous Read Timing Diagram tRDpwh SLRD tRDpwl FLAGS tXFD tXFLG DATA N tOEon SLOE N+1 tOEoff In the following table, the Slave FIFO asynchronous parameter values use internal IFCLK setting at 48 MHz. Table 17. Slave FIFO Asynchronous Read Parameters Min Max Unit tRDpwl Parameter SLRD Pulse Width LOW Description 50 – ns tRDpwh SLRD Pulse Width HIGH 50 – ns tXFLG SLRD to FLAGS Output Propagation Delay – 70 ns tXFD SLRD to FIFO Data Output Propagation Delay – 15 ns tOEon SLOE Turn-on to FIFO Data Valid – 10.5 ns tOEoff SLOE Turn-off to FIFO Data Hold – 10.5 ns Document Number: 38-08039 Rev. *J Page 54 of 72 [+] Feedback CY7C64713 Slave FIFO Synchronous Write In the following figure, dashed lines indicate signals with programmable polarity. Figure 21. Slave FIFO Synchronous Write Timing Diagram tIFCLK IFCLK SLWR DATA tSWR tWRH N Z tSFD Z tFDH FLAGS tXFLG The following table provides the Slave FIFO Synchronous Write Parameters with Internally Sourced IFCLK. [36] Table 18. Slave FIFO Synchronous Write Parameters with Internally Sourced IFCLK Min Max Unit tIFCLK Parameter IFCLK Period Description 20.83 – ns tSWR SLWR to Clock Setup Time 18.1 – ns tWRH Clock to SLWR Hold Time 0 – ns tSFD FIFO Data to Clock Setup Time 9.2 – ns tFDH Clock to FIFO Data Hold Time 0 – ns tXFLG Clock to FLAGS Output Propagation Time – 9.5 ns The following table provides the Slave FIFO Synchronous Write Parameters with Externally Sourced IFCLK. [36] Table 19. Slave FIFO Synchronous Write Parameters with Externally Sourced IFCLK [36] Min Max Unit tIFCLK Parameter IFCLK Period Description 20.83 200 ns tSWR SLWR to Clock Setup Time 12.1 – ns tWRH Clock to SLWR Hold Time 3.6 – ns tSFD FIFO Data to Clock Setup Time 3.2 – ns tFDH Clock to FIFO Data Hold Time 4.5 – ns tXFLG Clock to FLAGS Output Propagation Time – 13.5 ns Note 36. IFCLK must not exceed 48 MHz. Document Number: 38-08039 Rev. *J Page 55 of 72 [+] Feedback CY7C64713 Slave FIFO Asynchronous Write In the following figure, dashed lines indicate signals with programmable polarity. Figure 22. Slave FIFO Asynchronous Write Timing Diagram tWRpwh SLWR/SLCS# tWRpwl tSFD tFDH DATA tXFD FLAGS In the following table, the Slave FIFO asynchronous parameter values use internal IFCLK setting at 48 MHz. Table 20. Slave FIFO Asynchronous Write Parameters with Internally Sourced IFCLK Parameter Description Min Max Unit tWRpwl SLWR Pulse LOW 50 – ns tWRpwh SLWR Pulse HIGH 70 – ns tSFD SLWR to FIFO DATA Setup Time 10 – ns tFDH FIFO DATA to SLWR Hold Time 10 – ns tXFD SLWR to FLAGS Output Propagation Delay – 70 ns Slave FIFO Synchronous Packet End Strobe In the following figure, dashed lines indicate signals with programmable polarity. Figure 23. Slave FIFO Synchronous Packet End Strobe Timing Diagram IFCLK tPEH PKTEND tSPE FLAGS tXFLG The following table provides the Slave FIFO Synchronous Packet End Strobe Parameters with Internally Sourced IFCLK. [37] Table 21. Slave FIFO Synchronous Packet End Strobe Parameters with Internally Sourced IFCLK Min Max Unit tIFCLK Parameter IFCLK Period Description 20.83 – ns tSPE PKTEND to Clock Setup Time 14.6 – ns tPEH Clock to PKTEND Hold Time 0 – ns tXFLG Clock to FLAGS Output Propagation Delay – 9.5 ns Note 37. IFCLK must not exceed 48 MHz. Document Number: 38-08039 Rev. *J Page 56 of 72 [+] Feedback CY7C64713 The following table provides the Slave FIFO Synchronous Packet End Strobe Parameters with Externally Sourced IFCLK. [38] Table 22. Slave FIFO Synchronous Packet End Strobe Parameters with Externally Sourced IFCLK Parameter Description Min Max Unit tIFCLK IFCLK Period 20.83 200 ns tSPE PKTEND to Clock Setup Time 8.6 – ns tPEH Clock to PKTEND Hold Time 2.5 – ns tXFLG Clock to FLAGS Output Propagation Delay – 13.5 ns There is no specific timing requirement that needs to be met for asserting the PKTEND pin concerning asserting SLWR. PKTEND is asserted with the last data value clocked into the FIFOs or thereafter. The only consideration is that the set up time tSPE and the hold time tPEH for PKTEND must be met. Although there are no specific timing requirements for asserting PKTEND in relation to SLWR, there exists a specific case condition that needs attention. When using the PKTEND to commit a one byte or word packet, an additional timing requirement must be met when the FIFO is configured to operate in auto mode and it is necessary to send two packets back to back: ■ A full packet (defined as the number of bytes in the FIFO meeting the level set in the AUTOINLEN register) committed automatically followed by ■ A short one byte or word packet committed manually using the PKTEND pin. In this particular scenario, the developer must assert the PKTEND at least one clock cycle after the rising edge that caused the last byte or word to be clocked into the previous auto committed packet. Figure 24 shows this scenario. X is the value the AUTOINLEN register is set to when the IN endpoint is configured to be in auto mode. Figure 24 shows a scenario where two packets are being committed. The first packet is committed automatically when the number of bytes in the FIFO reaches X (value set in AUTOINLEN register) and the second one byte or word short packet being committed manually using PKTEND. Note that there is at least one IFCLK cycle timing between asserting PKTEND and clocking of the last byte of the previous packet (causing the packet to be committed automatically). Failing to adhere to this timing results in the FX2 failing to send the one byte or word short packet. Figure 24. Slave FIFO Synchronous Write Sequence and Timing Diagram tIFCLK IFCLK tSFA tFAH FIFOADR >= tWRH >= tSWR SLWR tSFD DATA X-4 tFDH tSFD X-3 tFDH tSFD X-2 tFDH tSFD X-1 tFDH tSFD X tFDH tSFD tFDH 1 At least one IFCLK cycle tSPE tPEH PKTEND Note 38. IFCLK must not exceed 48 MHz. Document Number: 38-08039 Rev. *J Page 57 of 72 [+] Feedback CY7C64713 Slave FIFO Asynchronous Packet End Strobe In the following figure, dashed lines indicate signals with programmable polarity. Figure 25. Slave FIFO Asynchronous Packet End Strobe Timing Diagram tPEpwh PKTEND tPEpwl FLAGS tXFLG In the following table, the Slave FIFO asynchronous parameter values use internal IFCLK setting at 48 MHz. Table 23. Slave FIFO Asynchronous Packet End Strobe Parameters Parameter Description Min Max Unit tPEpwl PKTEND Pulse Width LOW 50 – ns tPWpwh PKTEND Pulse Width HIGH 50 – ns tXFLG PKTEND to FLAGS Output Propagation Delay – 115 ns Slave FIFO Output Enable In the following figure, dashed lines indicate signals with programmable polarity. Figure 26. Slave FIFO Output Enable Timing Diagram SLOE DATA tOEoff tOEon Table 24. Slave FIFO Output Enable Parameters Max Unit tOEon Parameter SLOE Assert to FIFO DATA Output Description 10.5 ns tOEoff SLOE Deassert to FIFO DATA Hold 10.5 ns Max Unit Slave FIFO Address to Flags/Data In the following figure, dashed lines indicate signals with programmable polarity. Figure 27. Slave FIFO Address to Flags/Data Timing Diagram FIFOADR [1.0] tXFLG FLAGS tXFD DATA N N+1 Table 25. Slave FIFO Address to Flags/Data Parameters Parameter Description tXFLG FIFOADR[1:0] to FLAGS Output Propagation Delay 10.7 ns tXFD FIFOADR[1:0] to FIFODATA Output Propagation Delay 14.3 ns Document Number: 38-08039 Rev. *J Page 58 of 72 [+] Feedback CY7C64713 Slave FIFO Synchronous Address Figure 28. Slave FIFO Synchronous Address Timing Diagram IFCLK SLCS/FIFOADR [1:0] tSFA tFAH The following table provides the Slave FIFO Synchronous Address Parameters.[39] Table 26. Slave FIFO Synchronous Address Parameters Parameter Description Min Max Unit 20.83 200 ns FIFOADR[1:0] to Clock Setup Time 25 – ns Clock to FIFOADR[1:0] Hold Time 10 – ns tIFCLK Interface Clock Period tSFA tFAH Slave FIFO Asynchronous Address In the following figure, dashed lines indicate signals with programmable polarity. Figure 29. Slave FIFO Asynchronous Address Timing Diagram SLCS/FIFOADR [1:0] tSFA tFAH RD/WR/PKTEND In the following table, the Slave FIFO asynchronous parameter values use internal IFCLK setting at 48 MHz. Table 27. Slave FIFO Asynchronous Address Parameters Min Unit tSFA Parameter FIFOADR[1:0] to RD/WR/PKTEND Setup Time Description 10 ns tFAH RD/WR/PKTEND to FIFOADR[1:0] Hold Time 10 ns Note 39. IFCLK must not exceed 48 MHz. Document Number: 38-08039 Rev. *J Page 59 of 72 [+] Feedback CY7C64713 Sequence Diagram Single and Burst Synchronous Read Example Figure 30. Slave FIFO Synchronous Read Sequence and Timing Diagram tIFCLK IFCLK tSFA tSFA tFAH tFAH FIFOADR t=0 tSRD T=0 tRDH >= tSRD >= tRDH SLRD t=3 t=2 T=3 T=2 SLCS tXFLG FLAGS tXFD tXFD Data Driven: N DATA N+1 N+1 N+2 N+3 tOEon tOEoff tOEon tXFD tXFD N+4 tOEoff SLOE t=4 t=1 T=4 T=1 Figure 31. Slave FIFO Synchronous Sequence of Events Diagram IFCLK FIFO POINTER N IFCLK IFCLK N N+1 FIFO DATA BUS Not Driven Driven: N N+1 N+1 Not Driven ■ At t = 1, SLOE is asserted. SLOE is an output enable only, whose sole function is to drive the data bus. The data that is driven on the bus is the data that the internal FIFO pointer is currently pointing to. In this example it is the first data value in the FIFO. Note The data is pre-fetched and is driven on the bus when SLOE is asserted. Document Number: 38-08039 Rev. *J IFCLK N+3 IFCLK N+4 N+1 IFCLK N+4 SLRD N+2 N+3 N+4 IFCLK N+4 SLOE N+4 Not Driven ■ At t = 2, SLRD is asserted. SLRD must meet the setup time of tSRD (time from asserting the SLRD signal to the rising edge of the IFCLK) and maintain a minimum hold time of tRDH (time from the IFCLK edge to the deassertion of the SLRD signal). If the SLCS signal is used, it must be asserted with SLRD, or before SLRD is asserted (that is, the SLCS and SLRD signals must both be asserted to start a valid read condition). ■ The FIFO pointer is updated on the rising edge of the IFCLK, while SLRD is asserted. This starts the propagation of data from the newly addressed location to the data bus. After a propagation delay of tXFD (measured from the rising edge of IFCLK) the new data value is present. N is the first data value read from the FIFO. To have data on the FIFO data bus, SLOE MUST also be asserted. At t = 0 the FIFO address is stable and the signal SLCS is asserted (SLCS may be tied low in some applications). Note tSFA has a minimum of 25 ns. This means when IFCLK is running at 48 MHz, the FIFO address setup time is more than one IFCLK cycle. IFCLK N+2 SLRD SLOE Figure 30 shows the timing relationship of the SLAVE FIFO signals during a synchronous FIFO read using IFCLK as the synchronizing clock. This diagram illustrates a single read followed by a burst read. ■ N+1 SLOE SLRD SLRD SLOE IFCLK IFCLK The same sequence of events are shown for a burst read and are marked with the time indicators of T = 0 through 5. Page 60 of 72 [+] Feedback CY7C64713 Note For the burst mode, the SLRD and SLOE are left asserted during the entire duration of the read. In the burst read mode, when SLOE is asserted, data indexed by the FIFO pointer is on the data bus. During the first read cycle, on the rising edge of the clock the FIFO pointer is updated and increments to point to address N + 1. For each subsequent rising edge of IFCLK, while the SLRD is asserted, the FIFO pointer is incremented and the next data value is placed on the data bus. Single and Burst Synchronous Write In the following figure, dashed lines indicate signals with programmable polarity. Figure 32. Slave FIFO Synchronous Write Sequence and Timing Diagram tIFCLK IFCLK tSFA tSFA tFAH tFAH FIFOADR t=0 tSWR tWRH >= tWRH >= tSWR T=0 SLWR t=2 T=2 t=3 T=5 SLCS tXFLG tXFLG FLAGS tFDH tSFD tSFD N+1 N DATA t=1 tFDH T=1 tSFD tSFD tFDH N+3 N+2 T=3 tFDH T=4 tSPE tPEH PKTEND Figure 32 shows the timing relationship of the SLAVE FIFO signals during a synchronous write using IFCLK as the synchronizing clock. This diagram illustrates a single write followed by burst write of 3 bytes and committing all 4 bytes as a short packet using the PKTEND pin. ■ At t = 0 the FIFO address is stable and the signal SLCS is asserted (SLCS may be tied low in some applications). Note tSFA has a minimum of 25 ns. This means when IFCLK is running at 48 MHz, the FIFO address setup time is more than one IFCLK cycle. ■ At t = 1, the external master or peripheral must output the data value onto the data bus with a minimum set up time of tSFD before the rising edge of IFCLK. ■ At t = 2, SLWR is asserted. The SLWR must meet the setup time of tSWR (time from asserting the SLWR signal to the rising edge of IFCLK) and maintain a minimum hold time of tWRH (time from the IFCLK edge to the deassertion of the SLWR signal). If SLCS signal is used, it must be asserted with SLWR or before SLWR is asserted. (that is the SLCS and SLWR signals must both be asserted to start a valid write condition). ■ While the SLWR is asserted, data is written to the FIFO and on the rising edge of the IFCLK, the FIFO pointer is incremented. Document Number: 38-08039 Rev. *J The FIFO flag is also updated after a delay of tXFLG from the rising edge of the clock. The same sequence of events are also shown for a burst write and are marked with the time indicators of T = 0 through 5. Note For the burst mode, SLWR and SLCS are left asserted for the entire duration of writing all the required data values. In this burst write mode, after the SLWR is asserted, the data on the FIFO data bus is written to the FIFO on every rising edge of IFCLK. The FIFO pointer is updated on each rising edge of IFCLK. In Figure 32, after the four bytes are written to the FIFO, SLWR is deasserted. The short 4-byte packet is committed to the host by asserting the PKTEND signal. There is no specific timing requirement that must be met for asserting the PKTEND signal with regards to asserting the SLWR signal. PKTEND is asserted with the last data value or thereafter. The only consideration is the setup time tSPE and the hold time tPEH must be met. In the scenario of Figure 32, the number of data values committed includes the last value written to the FIFO. In this example, both the data value and the PKTEND signal are clocked on the same rising edge of IFCLK. PKTEND is asserted in subsequent clock cycles. The FIFOADDR lines must be held constant during the PKTEND assertion. Page 61 of 72 [+] Feedback CY7C64713 packet committed manually using the PKTEND pin. In this case, the external master must make sure to assert the PKTEND pin at least one clock cycle after the rising edge that caused the last byte or word to be clocked into the previous auto committed packet (the packet with the number of bytes equal to what is set in the AUTOINLEN register). Refer to Table 19 on page 55 for further details on this timing. Although there are no specific timing requirement for asserting PKTEND, there is a specific corner case condition that needs attention while using the PKTEND to commit a one byte or word packet. Additional timing requirements exist when the FIFO is configured to operate in auto mode and it is necessary to send two packets: a full packet (full defined as the number of bytes in the FIFO meeting the level set in AUTOINLEN register) committed automatically followed by a short one byte or word Sequence Diagram of a Single and Burst Asynchronous Read Figure 33. Slave FIFO Asynchronous Read Sequence and Timing Diagram tSFA tFAH tSFA tFAH FIFOADR t=0 tRDpwl tRDpwh tRDpwl T=0 tRDpwl tRDpwh tRDpwl tRDpwh tRDpwh SLRD t=2 t=3 T=2 T=3 T=5 T=4 T=6 SLCS tXFLG tXFLG FLAGS tXFD Data (X) Driven DATA tXFD tXFD N N N+3 N+2 tOEon tOEoff tOEon tXFD N+1 tOEoff SLOE t=4 t=1 T=7 T=1 Figure 34. Slave FIFO Asynchronous Read Sequence of Events Diagram SLOE FIFO POINTER N FIFO DATA BUS Not Driven SLRD SLRD SLOE SLOE SLRD SLRD SLRD SLRD SLOE N N N+1 N+1 N+1 N+1 N+2 N+2 N+3 N+3 Driven: X N N Not Driven N N+1 N+1 N+2 N+2 Not Driven Figure 33 shows the timing relationship of the SLAVE FIFO signals during an asynchronous FIFO read. It shows a single read followed by a burst read. ■ The data that drives after asserting SLRD, is the updated data from the FIFO. This data is valid after a propagation delay of tXFD from the activating edge of SLRD. In Figure 33, data N is the first valid data read from the FIFO. For data to appear on the data bus during the read cycle (that is, SLRD is asserted), SLOE MUST be in an asserted state. SLRD and SLOE can also be tied together. ■ At t = 0 the FIFO address is stable and the SLCS signal is asserted. ■ At t = 1, SLOE is asserted. This results in the data bus being driven. The data that is driven on to the bus is previous data, it data that was in the FIFO from a prior read cycle. The same sequence of events is also shown for a burst read marked with T = 0 through 5. At t = 2, SLRD is asserted. The SLRD must meet the minimum active pulse of tRDpwl and minimum de-active pulse width of tRDpwh. If SLCS is used then, SLCS must be in asserted with SLRD or before SLRD is asserted (that is, the SLCS and SLRD signals must both be asserted to start a valid read condition). Note In burst read mode, during SLOE is assertion, the data bus is in a driven state and outputs the previous data. After the SLRD is asserted, the data from the FIFO is driven on the data bus (SLOE must also be asserted) and then the FIFO pointer is incremented. ■ Document Number: 38-08039 Rev. *J Page 62 of 72 [+] Feedback CY7C64713 Sequence Diagram of a Single and Burst Asynchronous Write In the following figure, dashed lines indicate signals with programmable polarity. Figure 35. Slave FIFO Asynchronous Write Sequence and Timing Diagram tSFA tFAH tSFA tFAH FIFOADR t=0 tWRpwl tWRpwh T=0 tWRpwl tWRpwl tWRpwh tWRpwl tWRpwh tWRpwh SLWR t=3 t =1 T=1 T=3 T=4 T=6 T=7 T=9 SLCS tXFLG tXFLG FLAGS tSFD tFDH tSFD tFDH tSFD tFDH tSFD tFDH N+1 N+2 N+3 N DATA t=2 T=2 T=5 T=8 tPEpwl tPEpwh PKTEND Figure 35 shows the timing relationship of the SLAVE FIFO write in an asynchronous mode. This diagram shows a single write followed by a burst write of 3 bytes and committing the 4-byte-short packet using PKTEND. ■ At t = 0 the FIFO address is applied, insuring that it meets the setup time of tSFA. If SLCS is used, it must also be asserted (SLCS may be tied low in some applications). ■ At t = 1 SLWR is asserted. SLWR must meet the minimum active pulse of tWRpwl and minimum de-active pulse width of tWRpwh. If the SLCS is used, it must be in asserted with SLWR or before SLWR is asserted. ■ At t = 2, data must be present on the bus tSFD before the deasserting edge of SLWR. ■ At t = 3, deasserting SLWR causes the data to be written from the data bus to the FIFO and then increments the FIFO pointer. The FIFO flag is also updated after tXFLG from the deasserting edge of SLWR. Document Number: 38-08039 Rev. *J The same sequence of events are shown for a burst write and is indicated by the timing marks of T = 0 through 5. Note In the burst write mode, after SLWR is deasserted, the data is written to the FIFO and then the FIFO pointer is incremented to the next byte in the FIFO. The FIFO pointer is post incremented. In Figure 35, after the four bytes are written to the FIFO and SLWR is deasserted, the short 4-byte packet is committed to the host using the PKTEND. The external device must be designed to not assert SLWR and the PKTEND signal at the same time. It must be designed to assert the PKTEND after SLWR is deasserted and has met the minimum deasserted pulse width. The FIFOADDR lines are to be held constant during the PKTEND assertion. Page 63 of 72 [+] Feedback CY7C64713 Ordering Information Ordering Code Package Type RAM Size # Prog I/Os 8051 Address/Data Busses CY7C64713-128AXC 128-pin TQFP - Pb-free 16K 40 16/8 bit CY7C64713-100AXC 100-pin TQFP - Pb-free 16K 40 – CY7C64713-56PVXC 56-pin SSOP - Pb-free 16K 24 – CY7C64713-56LTXC 56-pin QFN - Pb-free 16K 24 – CY3674 EZ-USB FX1 Development Kit Ordering Code Definitions CY 7 C 64 713 - XXXXX X X X Tape and Reel Temperature Range: X = C or I or A C = Commercial grade; I = Industrial grade; A = Automotive grade X = Pb-free Package Type: XXXXX = 128A or 100A or 56PV or 56LT 128A = 128-pin TQFP; 100A = 100-pin TQFP; 56PV = 56-pin SSOP; 56LT = 56-pin QFN Part Number Family Code: 64 = USB Technology Code: C = CMOS Marketing Code: 7 = Cypress Products Company ID: CY = Cypress Document Number: 38-08039 Rev. *J Page 64 of 72 [+] Feedback CY7C64713 Package Diagrams The FX1 is available in four packages: ■ 56-pin SSOP ■ 56-pin QFN ■ 100-pin TQFP ■ 128-pin TQFP Figure 36. 56-pin SSOP 300 Mils O563 51-85062 *D Document Number: 38-08039 Rev. *J Page 65 of 72 [+] Feedback CY7C64713 Figure 37. 56-pin QFN 8 × 8 × 1 mm LT56B 4.5 × 5.2 EPAD (Sawn) 001-53450 *B Document Number: 38-08039 Rev. *J Page 66 of 72 [+] Feedback CY7C64713 Figure 38. 100-pin TQFP (14 × 20 × 1.4 mm) A100RA 51-85050 *D Document Number: 38-08039 Rev. *J Page 67 of 72 [+] Feedback CY7C64713 Figure 39. 128-pin TQFP (14 × 20 × 1.4 mm) A128RA 51-85101 *E Quad Flat Package No Leads (QFN) Package Design Notes Electrical contact of the part to the Printed Circuit Board (PCB) is made by soldering the leads on the bottom surface of the package to the PCB. As a result, special attention is required to the heat transfer area below the package to provide a good thermal bond to the circuit board. A Copper (Cu) fill is to be designed into the PCB as a thermal pad under the package. Heat is transferred from the FX1 through the device’s metal paddle on the bottom side of the package. Heat from here, is conducted to the PCB at the thermal pad. It is then conducted from the thermal pad to the PCB inner ground plane by a 5 × 5 array of via. A via is a plated through hole in the PCB with a finished diameter of 13 mil. The QFN’s metal die paddle must be soldered to the PCB’s thermal pad. Solder mask is placed on the board top side over each via to resist solder flow into the via. The mask on the top side also minimizes outgassing during the solder reflow process. Document Number: 38-08039 Rev. *J For further information on this package design please refer to ‘Application Notes for Surface Mount Assembly of Amkor's MicroLeadFrame (MLF) Packages’. This can be found on Amkor's website http://www.amkor.com. The application note provides detailed information on board mounting guidelines, soldering flow, rework process, and so on. Figure 40 on page 69 displays a cross-sectional area underneath the package. The cross section is of only one via. The solder paste template needs to be designed to allow at least 50% solder coverage. The thickness of the solder paste template must be 5 mil. It is recommended that ‘No Clean’ type 3 solder paste is used for mounting the part. Nitrogen purge is recommended during reflow. Figure 41 on page 69 is a plot of the solder mask pattern and Figure 42 on page 69 displays an X-Ray image of the assembly (darker areas indicate solder). Page 68 of 72 [+] Feedback CY7C64713 Figure 40. Cross section of the Area Underneath the QFN Package 0.017” dia Solder Mask Cu Fill Cu Fill PCB Material Via hole for thermally connecting the QFN to the circuit board ground plane. 0.013” dia PCB Material This figure only shows the top three layers of the circuit board: Top Solder, PCB Dielectric, and the Ground Plane. Figure 41. Plot of the Solder Mask (White Area) Figure 42. X-ray Image of the Assembly Document Number: 38-08039 Rev. *J Page 69 of 72 [+] Feedback CY7C64713 Acronyms Acronym Document Conventions Description Units of Measure ASIC application specific integrated circuit ATA advanced technology attachment cm centi meter CPU central processing unit °C degree Celsius DID device identifier kHZ kilo Hertz DSL digital service line k kilo ohms DSP digital signal processor Mbps Mega bits per second ECC error correction code MBPs Mega bytes per second EEPROM electrically erasable programmable read-only memory MHz Mega Hertz EPP enhanced parallel port µA micro Amperes FIFO first in first out µs micro seconds GPIF general programmable interface µW micro Watts GPIO general purpose input/output mA milli Amperes I/O input/output mm milli meter LAN local area network ms milli seconds LSB least significant bit mW milli Watts MSB most significant bit ns nano seconds PCB printed circuit board ohms PCMCIA personal computer memory card international association ppm parts per million % percent PID product identifier pF pico Farad PLL phase-locked loop V Volts QFN quad flat no leads RAM random access memory SFR special function register SIE serial interface engine SOF start of frame SSOP shrink small-outline package TQFP thin quad flat pack USARTS universal serial asynchronous receiver/transmitter USB universal serial bus UTOPIA universal test and operations physical-layer interface VID vendor identifier Document Number: 38-08039 Rev. *J Symbol Unit of Measure Page 70 of 72 [+] Feedback CY7C64713 Document History Page Document Title: CY7C64713, EZ-USB FX1™ USB Microcontroller Full Speed USB Peripheral Controller Document Number: 38-08039 Revision ECN Orig. of Change Submission Date ** 132091 KKU 02/10/04 New Datasheet. *A 230709 KKU SEE ECN Changed Lead free Marketing part numbers in Ordering Information according to spec change in 28-00054. *B 307474 BHA SEE ECN Changed default PID in Table 2 on page 5. Updated register table. Removed word compatible where associated with I2C. Changed Set-up to Setup. Added Power Dissipation. Changed Vcc from ± 10% to ± 5% Added values for VIH_X, VIL_X Added values for ICC Added values for ISUSP Removed IUNCONFIGURED from DC Characteristics on page 47. Changed PKTEND to FLAGS output propagation delay (asynchronous interface) in Table 10-14 from a maximum value of 70 ns to 115 ns. Removed 56 SSOP and added 56 QFN package. Provided additional timing restrictions and requirement regarding the use of PKTEND pin to commit a short one byte/word packet subsequent to committing a packet automatically (when in auto mode). Added part number CY7C64714 ideal for battery powered applications. Changed Supply Voltage in section 8 to read +3.15V to +3.45V. Added Min Vcc Ramp Up time (0 to 3.3 V). Removed Preliminary. *C 392702 BHA SEE ECN Corrected signal name for pin 54 in Figure 10 on page 18. Added information on the AUTOPTR1/AUTOPTR2 address timing with regards to data memory read/write timing diagram. Removed TBD in Table 15 on page 53. Added section PORTC Strobe Feature Timings on page 51. *D 1664787 CMCC/ JASM See ECN Added the 56 pin SSOP pinout and package information. Delete CY7C64714. *E 2088446 JASM See ECN Updated package diagrams. *F 2710327 DPT 05/22/2009 Added 56-Pin QFN (8 × 8 mm) package diagram Updated ordering information for CY7C64713-56LTXC part *G 2765406 ODC 09/17/2009 Added Pb-free for the CY7C64713-56LTXC part in the ordering information table. Updated 56-Pin Sawn QFN package diagram. *H 2896318 ODC 03/18/2010 Removed obsolete part CY7C64713-56LFXC. Updated all package diagrams. *I 3186891 ODC 03/03/2011 Template updates. Updated package diagrams: 51-85144 , 51-85050, 51-85101 *J 3259101 ODC 05/17/2011 Added Ordering Code Definitions. Updated Package Diagrams. Added Acronyms and Units of Measure. Updated in new template. Document Number: 38-08039 Rev. *J Description of Change Page 71 of 72 [+] Feedback CY7C64713 Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office closest to you, visit us at cypress.com/sales. Products Automotive Interface Lighting & Power Control PSoC Solutions cypress.com/go/automotive Clocks & Buffers cypress.com/go/clocks psoc.cypress.com/solutions cypress.com/go/interface PSoC 1 | PSoC 3 | PSoC 5 cypress.com/go/powerpsoc cypress.com/go/plc Memory cypress.com/go/memory Optical & Image Sensing cypress.com/go/image PSoC cypress.com/go/psoc Touch Sensing cypress.com/go/touch USB Controllers Wireless/RF cypress.com/go/USB cypress.com/go/wireless © Cypress Semiconductor Corporation, 2004-2011. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign), United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of, and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without the express written permission of Cypress. Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Use may be limited by and subject to the applicable Cypress software license agreement. Document Number: 38-08039 Rev. *J Revised May 17, 2011 Page 72 of 72 EZ-USB FX1, EZ-USB FX2LP, EZ-USB FX2, and ReNumeration are trademarks, and EZ-USB is a registered trademark, of Cypress Semiconductor. All product and company names mentioned in this document are the trademarks of their respective holders. [+] Feedback