ON LE2416DXATBG 16 kb i2c cmos serial eeprom Datasheet

LE2416DXA
16 kb I2C CMOS Serial EEPROM
Overview
The LE2416DXA is two-wire serial interface EEPROM (Electrically
Erasable and Programmable ROM). This device realizes high speed and a
high level reliability by high performance CMOS EEPROM technology.
This device is compatible with I2C memory protocol, therefore it is best
suited for application that requires re-writable nonvolatile parameter
memory.
www.onsemi.com
Function
 Capacity : 16k bits (2k  8 bits)
 Single supply voltage : 1.7 V to 3.6 V
 Operating temperature : 40ºC to +85ºC
WLCSP6, 0.80x1.20
 Interface : Two wire serial interface (I2C Bus*)
 Operating clock frequency : 400 kHz (Fast), 1000 kHz (Fast-Plus)
 Low Power consumption

: Standby : 2 µA (max.)
: Active (Read, 400 kHz) : 0.5 mA (max.)
Active (Read, 1000 kHz) : 2.0 mA (max.)
 Automatic page write mode : 16 Bytes
 Read mode : Sequential Read and random read
 Slave Address : Slave address in 7 bit format is 050 or 054 depending of polarity of pin B3 (TEST)
 Erase/Write cycles : 106 cycles (Page Write)
 Data Retention : 20 years
 High reliability : Adopts proprietary symmetric memory array configuration (USP6947325)
Hardware write protect feature
Noise filters connected to SCL and SDA pins
Incorporates a feature to prohibit write operations under low voltage conditions.
 Package : LE2416DXA WLP6(0.801.20) 0.33 mm height
Specifications
Absolute Maximum Ratings at Ta = 25C
Parameter
Symbol
Conditions
Ratings
Unit
0.5 to +4.6
V
DC input voltage
0.5 to VCC+0.5
V
Over-shoot voltage
1.0 to VCC+1.0
V
65 to +150
C
Supply voltage
Storage temperature
Tstg
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed,
damage may occur and reliability may be affected.
* This product is licensed from Silicon Storage Technology, Inc. (USA).
ORDERING INFORMATION
See detailed ordering and shipping information on page 17 of this data sheet.
© Semiconductor Components Industries, LLC, 2016
August 2016 - Rev. 1
1
Publication Order Number :
LE2416DXA/D
LE2416DXA
Recommended Operating Conditions
Ratings
Parameter
Symbol
Conditions
Unit
min
typ
max
Operating supply voltage
1.7
3.6
V
Operating temperature
40
+85
C
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the Recommended
Operating Ranges limits may affect device reliability.
DC Electrical Characteristics
Spec.
Parameter
Symbol
Conditions
Unit
min
typ
max
f = 400 kHz, VCC = VCC Max
0.5
f =1000 kHz, VCC = VCC Max
2.0
ICC2
f = 1000 kHz / 400 kHz,
tWC = 5 ms, VCC = VCC Max
3.0
mA
Standby current
ISB
WP = VCC2 = VCC
VIN = VCC or VSS
2
µA
Input leakage current
ILI
VIN = VSS to VCC, VCC = VCC Max
+2.0
µA
Output leakage current
ILO
VIN = VSS to VCC, VCC = VCC Max
+2.0
µA
Input Low voltage
VIL
VCC  0.3
V
Input High voltage
VIH
Supply current at reading
ICC1
Supply current at writing
2.0
2.0
mA
VCC  0.7
VOL2
V
IOL = 1.0 mA, VCC = 1.7 V
0.2
V
0.4
V
IOL = 1.2 mA, VCC = 2.0 V
Output Low voltage
VOL1
IOL = 2.1 mA, VCC = 2.0 V
IOL = 3.0 mA, VCC = 2.5 V
Capacitance at Ta = 25C, f = 1 MHz
Parameter
Symbol
Conditions
max
Unit
In/Output pin capacitance
CI/O
VI/O = 0 V (SDA)
10
pF
Input pin capacitance
CI
VIN = 0 V
10
pF
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be
indicated by the Electrical Characteristics if operated under different conditions.
www.onsemi.com
2
LE2416DXA
Fast-Plus (1000 kHz)
Spec.
Parameter
Symbol
Unit
min
typ
max
Slave mode SCL clock frequency
fSCLS
0
SCL clock low time
tLOW
500
1000
ns
SCL clock high time
tHIGH
300
ns
SDA output delay time
tAA
50
450
kHz
ns
SDA data output hold time
tDH
50
ns
Start condition setup time
tSU.STA
250
ns
Start condition hold time
tHD.STA
250
ns
Data in setup time
tSU.DAT
50
ns
Data in hold time
tHD.DAT
0
ns
Stop condition setup time
tSU.STO
250
ns
SCL SDA rise time
tR
120
ns
SCL SDA fall time
tF
120
ns
Bus release time
tBUF
Noise suppression time
tSP
50
ns
Write time
tWC
5
ms
500
ns
Fast (400 kHz)
Spec.
Parameter
Symbol
Unit
min
typ
Slave mode SCL clock frequency
fSCLS
0
SCL clock low time
tLOW
1200
SCL clock high time
tHIGH
600
SDA output delay time
tAA
100
SDA data output hold time
tDH
100
max
400
kHz
ns
ns
900
ns
ns
Start condition setup time
tSU.STA
600
ns
Start condition hold time
tHD.STA
600
ns
Data in setup time
tSU.DAT
100
ns
Data in hold time
tHD.DAT
0
ns
Stop condition setup time
tSU.STO
600
ns
SCL SDA rise time
tR
300
SCL SDA fall time
tF
Bus release time
tBUF
Noise suppression time
tSP
50
ns
Write time
tWC
5
ms
www.onsemi.com
3
300
ns
1200
ns
ns
LE2416DXA
Standard (100 kHz)
Spec.
Parameter
Symbol
Unit
min
typ
max
Slave mode SCL clock frequency
fSCLS
0
SCL clock low time
tLOW
4700
ns
SCL clock high time
tHIGH
4000
ns
SDA output delay time
tAA
100
100
3500
kHz
ns
SDA data output hold time
tDH
100
ns
Start condition setup time
tSU.STA
4700
ns
Start condition hold time
tHD.STA
4000
ns
Data in setup time
tSU.DAT
250
ns
Data in hold time
tHD.DAT
0
ns
Stop condition setup time
tSU.STO
4000
ns
SCL SDA rise time
tR
1000
SCL SDA fall time
tF
300
Bus release time
tBUF
Noise suppression time
tSP
50
ns
Write time
tWC
5
ms
AC measurement condition
Input pulse level
0.2  VCC to 0.8  VCC
Input pulse rise / fall time
20 ns
Output timing reference level
0.5  VCC
Output load
100 pF
www.onsemi.com
4
4700
ns
ns
ns
LE2416DXA
Package Dimensions
unit : mm
WLCSP6, 0.80x1.20
CASE 567HM
ISSUE O
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. COPLANARITY APPLIES TO SPHERICAL
CROWNS OF SOLDER BALLS.
A B
E
PIN A1
REFERENCE
D
0.05 C
2X
0.05 C
2X
DIM
A
A1
b
D
E
e
TOP VIEW
A
0.05 C
A1
RECOMMENDED
SOLDERING FOOTPRINT*
0.08 C
NOTE 3
6X
C
SIDE VIEW
SEATING
PLANE
0.40
PITCH
A1
PACKAGE
OUTLINE
e
b
0.05 C A B
0.03 C
MILLIMETERS
MIN
MAX
0.33
0.03
0.13
0.15
0.25
0.80 BSC
1.20 BSC
0.40 BSC
6X
e
0.20
B
0.40
PITCH
A
1
2
DIMENSIONS: MILLIMETERS
3
BOTTOM VIEW
*For additional information on our Pb-Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
www.onsemi.com
5
LE2416DXA
Pin Assignment
Top View
Ball side View
A
SCL
WP
VCC
SDA
GND
TEST
B
B
SDA
GND
TEST
SCL
WP
VCC
A
1
2
3
1
2
3
Pin Descriptions
A1
SCL
Serial clock input
A2
WP
Write protect
A3
VCC
Power supply
B1
SDA
Serial data in/output
B2
GND
Ground
B3
TEST
Slave Device Address 2
Block Diagram
High voltage generator
X decoder
SCL
Write controller
Serial controller
TEST
WP
SDA
EEPROM Array
Serial-Parallel converter
www.onsemi.com
6
LE2416DXA
Bus timing
tHIGH
tF
tLOW
tR
tSP
SCL
tSU.STA
tHD.STA
tSU.DAT
tHD.DAT
tSU.STO
tSP
SDA/IN
tAA
tBUF
tDH
SDA/OUT
Write timing
tWC
SCL
D0
SDA
Write Data
Acknowledge
Stop
condition
Start
condition
Pin Function
SCL (Serial clock)
The SCL signal is used to control serial input data timing. The SCL is used to latch input data synchronously
at the rising edge and read output data synchronously at the falling edge.
SDA (Serial input / output data)
The SDA pin is bidirectional for serial data transfer. It is an open-drain structure that needs to be pulled up by
resistor.
TEST (Slave address)
TEST pin represents S2. TEST pulled high (1.8 V) results in 7bit device address of 0x54. TEST pulled low
results in 7 bit device address of 0x50.
The TEST must be tied to VCC or GND.
WP (Write protect)
When the WP input is high, write protection is enabled. When WP input is either low or floating, write
protection is disabled. The read operation is always activated irrespective of the WP pin status.
www.onsemi.com
7
LE2416DXA
Functional Description
The device supports the I2C protocol. Any device that sends data on to the bus is defined to be a transmitter,
and any device that reads the data to a receiver. The device that controls the data transfer is known as the
bus master, and the other as the slave device.
1) Start Condition
A Start condition needs to start the EEPROM operation, it is to set falling edge of the SDA while the SCL
is stable in the high status.
2) Stop Condition
A Start condition is identified by rising edge of the SDA signal while the SCL is stable in the high status.
The device becomes the standby mode from a Read operation by a Stop condition. In a write sequence,
a stop condition is trigger to terminate the write data inputs and it is trigger to start the internal write cycle.
After the internally write cycle time which is specified as tWC, the device enters a standby mode.
tSU.STA
tSU.STO
tHD.STA
SCL
SDA
Stop
condition
Start
condition
3) Data Input
During data input, the device latches the SDA on the rising edge of the SCL. For correct the operation,
The SDA must be stable during the rising edge of the SCL.
tSU.DAT
tHD.DAT
SCL
SDA
www.onsemi.com
8
LE2416DXA
4) Acknowledge Bit (ACK)
The Acknowledge Bit is used to indicate a successful byte data transfer. The receiver sends a zero to
acknowledge that it has received each word (Device Code, Slave Address etc) from the transmitter.
SCL
(From Transmitter)
8
1
9
SDA
(From Transmitter)
SDA
(EEPROM output)
Acknowledge
Bit output
Start
condition
tAA
tDH
5) Device addressing
To transmit between the bus master and slave device (EEPROM), the master must send a Start condition
to the EEPROM. The device address word of the EEPROM consists of 4-bit Device Code, 3-bit Memory
address and 1-bit read/write code. By sending these, it becomes possible to communicate between the
bus master and the EEPROM.
The upper 4-bit of the device address word are called the Device Code, the Device Code of the EEPROM
uses 1010b fixed code. This device does not have the Slave address.
When the Device Code and Memory address (A10, A9, A8) are received on the SDA, the device only
responds. The 8th bit is the read/write bit. The bit is set to 1 for Read operation and 0 for Write operation.
If a match occurs on the Device Code, the corresponding device gives an acknowledgement on SDA
during the 9th bit time. If device does not match the Device Code, it deselects itself from the bus, and goes
into the Standby mode.
Memory
Address
Device Code
1
0
1
0
A10
A9
A8
R/W
LSB
MSB
Device address word
www.onsemi.com
9
LE2416DXA
6) EEPROM Write Operation
6)-1. Byte Write
The write operation requires a 7-bit device address (Device code + A10 + A9 + A8) with the 8th bit = 0
(write). Then the EEPROM sends acknowledgement 0 at the 9th clock cycle. After these, the EEPROM
receives word address (A7 to A0), and the EEPROM outputs acknowledgement 0. Then the EEPROM
receives 8-bit write data, the EEPROM outputs acknowledgement 0 after receipt of write data. If the
EEPROM receives a stop condition, the EEPROM enters an internally timed (tWC) write cycle and
terminates receipt of inputs until completion of the write cycle.
1 0 1 0 10
Data
A7 A6 A5 A4 A3 A2 A1 A0
ACK
R/W
D7 D6 D5 D4 D3 D2 D1 D0
ACK
Stop
SDA
Start
Word Address
ACK
Access from master device
6)-2. Page Write
The Page write allows up to 16 bytes to be written in a single write cycle. The page write is the same
sequence as the byte write except for inputting the more write data. The page write is initiated by a start
condition, device code, memory address and write data(n) with every 9th bit acknowledgement. The
device enters the page write operation if this device receives more write data(n+1) instead of receiving a
stop condition. The page address (A0 to A3) bits are automatically incremented on receiving write
data(n+1). The device can continue to receive write data up to 16 bytes. If the page address bits reaches
the last address of the page, the page address bits will roll over to the first address of the same page and
previous write data will be overwritten. After these, if the device receives a stop condition, the device
enters an internally timed (tWC×(n+x)) write cycle and terminates receipt of inputs until completion of the
write cycle.
1 0 1 0 A A9 A8 W
10
Data(n)
A7 A6 A5 A4 A3 A2 A1 A0
D7 D6 D5 D4 D3 D2 D1 D0
ACK
ACK
ACK
R/W
Data(n+x)
Data(n+1)
·····
D7 D6 ~ D1 D0
ACK
ACK
D7 D6 ~ D1 D0
ACK
D7 D6 ~ D1 D0
D7 D6 ~ D1 D0
ACK
Stop
SDA
Start
Word Address(n)
ACK
Access from master device
www.onsemi.com
10
LE2416DXA
6)-3. Acknowledge Polling
The Acknowledge Polling operation is used to show if the EEPROM is in an internally timed write cycle or
not. This operation is initiated by the stop condition after inputting write data. This requires the 8-bit
device address word with the 8th bit = 0 (write) following the start condition during an internally timed write
cycle. If the EEPROM is busy with the internal write cycle, no acknowledge will be returned. If the
EEPROM has terminated the internal write cycle, it responds with an acknowledge. The terminated write
cycle of the EEPROM can be known by this operation.
During Write
A
1 0 1 0 10 A9 A8 W
NO ACK
NO ACK
R/W
No Write
Start
A
1 0 1 0 10 A9 A8 W
Start
SDA
Start
During Write
R/W
A
1 0 1 0 10 A9 A8 W
······
ACK
R/W
Access from master device
www.onsemi.com
11
LE2416DXA
7) EEPROM Read Operation
7)-1. Current Address Read
The device has an internal address counter. It maintains that last address during the last read or write
operation, with incremented by one. The current address read accesses the address kept by the internal
address counter. After receiving a start condition and the device address word with the 8th bit = 1 (Read),
the EEPROM outputs the 8-bit current address data from following acknowledgement 0. If the EEPROM
receives acknowledgement 1 and a following stop condition, the EEPROM stops the read operation and
is returned to a standby mode. In case the EEPROM has accessed the last address of the last page at
previous read operation, the current address will roll over and returns to zero address. In case EEPROM
has accessed the last address of the last page at previous write operation, the current address roll over
within page addressing and returns to the first address in the same page.
The current address is valid while power is on. After power on, the current address will be reset (all 0).
Note: After the page write operation, the current address is the specified memory address in the last page
write, if the write data is more than 16-bytes.
Start
SDA
1 0 1
A
0 10 A9 A8 R
D7 D6 D5 D4 D3 D2 D1 D0
Stop
Data (n+1)
Device Address
NO ACK
ACK
R/W
Access from master device
7)-2. Random Read
The random read requires a dummy write to set read address. The EEPROM receives a start condition
and the device address (Device code + A10 + A9 + A8) with the 8th bit = 0 (write), the memory address.
The EEPROM outputs acknowledgement 0 after receiving memory address then enters a current
address read with receiving a start condition. The EEPROM outputs the read data of the address which
was defined in the dummy write operation. After receiving no acknowledgement and a following stop
condition, the EEPROM stops the random read operation and returns to a standby mode.
Word Address(n)
A7 A6 A5 A4 A3 A2 A1 A0
ACK
ACK
R/W
Dummy Write
Device Address
Data(n)
A
1 0 1 0 10 A9 A8 R
ACK
D7 D6 ~ D1 D0
ACK
Stop
1 0 1 0 A A9 A8 W
10
Start
SDA
Start
Device Address
NO ACK
R/W
Current Read
Access from master device
www.onsemi.com
12
LE2416DXA
7)-3. Sequential Read
The sequential read operation is initiated by either a current address read or random read. If the
EEPROM receives acknowledgement 0 after 8-bit read data, the read address is incremented and the
next 8-bit read data outputs. The current address will roll over and returns address zero if it reaches the
last address of the last page. The sequential read can be continued after roll over. The sequential read is
terminated if the EEPROM receives no acknowledgement and a following stop condition.
1 0 1
Data(n)
0
D7 D6 ~ D1 D0
ACK
Data(n+1)
Data(n+2)
D7 D6 ~ D1 D0
D7 D6 ~ D1 D0
ACK
ACK
ACK
R/W
Data(n+x)
D7 D6 ~ D1 D0
ACK
Stop
SDA
Start
Device Address
NO ACK
Access from master device
www.onsemi.com
13
LE2416DXA
Application Notes
1) Software reset function
Software reset (start condition + 9 dummy clock cycles + start condition), shown in the figure below, is
executed in order to avoid erroneous operation after power-on and to reset while the command input
sequence. During the dummy clock input period, the SDA bus must be opened (set to high by a pull-up
resistor). Since it is possible for the ACK output and read data to be output from the EEPROM during
the dummy clock period, forcibly entering H will result in an overcurrent flow.
Note that this software reset function does not work during the internal write cycle.
Dummy clock x 9
1
SCL
8
2
9
SDA
Start
Condition
Start
Condition
2) Pull-up resistor of SDA pin
Due to the demands of the I2C bus protocol function, the SDA pin must be connected to a pull-up resistor
(with a resistance from several k to several tens of k) without fail. The appropriate value must be
selected for this resistance (RPU) on the basis of the VIL and IIL of the microcontroller and other devices
controlling this product as well as the VOL – IOL characteristics of the product. Generally, when the
resistance is too high, the operating frequency will be restricted; conversely, when it is too low, the
operating current consumption will increase.
RPU maximum value
The maximum resistance must be set in such a
way that the bus potential, which is determined
by the sum total (IL) of the input leaks of the
devices connected to the SDA bus and by RPU,
can completely satisfy the input high level (VIH
min) of the microcontroller and EEPROM.
However, a resistance value that satisfies SDA
rise time tR and fall time tF must be set.
RPU
EEPROM
Master
Device
IL
SDA
CBUS
IL
RPU maximum value = (VCC  VIH) / IL
Example: When VCC = 3.0 V and IL = 2 A
RPU maximum value = (3.0 V  3.0 V  0.8) / 2 A = 300 k
RPU minimum value
A resistance corresponding to the low-level output voltage (VOL max) of EEPROM must be set.
RPU minimum value = (VCC  VOL) / IOL
Example: When VCC = 3.0 V, VOL = 0.4 V and IOL = 1 mA
RPU minimum value = (3.0 V  0.4) / 1 mA = 2.6 k
Recommended RPU setting
RPU is set to strike a good balance between the operating frequency requirements and power
consumption. If it is assumed that the SDA load capacitance is 50 pF and the SDA output data strobe
time is 500 ns, RPU will be about RPU = 500 ns/50 pF = 10 k.
www.onsemi.com
14
LE2416DXA
3) Precautions when turning on the power
This product contains a power-on reset circuit for preventing the inadvertent writing of data when the
power is turned on. The following conditions must be met in order to ensure stable operation of this
circuit. No data guarantees are given in the event of an instantaneous power failure during the internal
write operation.
symbol
tRISE
tOFF
Vbot
Parameter
Spec.
Typ.
–
–
–
Min.
–
10
–
Power rise time
Power off time
Power bottom voltage
Max.
100
–
0.2
Unit
ms
ms
V
tRISE
VCC
tOFF
Vbot
0V
Notes:
1) The SDA pin must be set to high and the SCL pin to low or high.
2) Steps must be taken to ensure that the SDA and SCL pins are not placed in a high-impedance state.
A. If it is not possible to satisfy the instruction 1 in Note above, and SDA is set to low during
power rise
After the power has stabilized, the SCL and SDA pins must be controlled as shown below, with both pins
set to high.
VCC
VCC
tLOW
SCL
SCL
SDA
SDA
tSU.DAT
tDH
tSU.DAT
B. If it is not possible to satisfy the instruction 2 in Note above
After the power has stabilized, software reset must be executed.
C. If it is not possible to satisfy the instructions both 1 and 2 in Note above
After the power has stabilized, the steps in A must be executed, then software reset must be executed.
4) Noise filter for the SCL and SDA pins
This product contains a filter circuit for eliminating noise at the SCL and SDA pins. Pulses of 100 ns or
less are not recognized because of this function.
5) Function to inhibit writing when supply voltage is low
This product contains a supply voltage monitoring circuit that inhibits inadvertent writing below the
guaranteed operating supply voltage range. The data is protected by ensuring that write operations are
not started at voltages (typ.) of 1.3 V and below.
www.onsemi.com
15
LE2416DXA
6) Notes on write protect operation
This product prohibits all memory array writing when the WP pin is high. To ensure full write protection,
the WP is set high for all periods from the start condition to the stop condition, and the conditions below
must be satisfied.
symbol
tSU.WP
tHD.WP
WP
Parameter
Min.
600
600
WP Setup time
WP Hold time
Spec.
Typ.
–
–
Max.
–
–
tHD.WP
tSU.WP
SCL
SDA
Stop Condition
Start Condition
www.onsemi.com
16
Unit
ns
ns
LE2416DXA
MARKING INFORMATION
LE2416DXA WLP6(0.80x1.20)
Part ID : 16D
Lot Number : 3digits
16D
Lot
ORDERING INFORMATION
Device
LE2416DXATBG
Package
Shipping (Qty / Packing)
WLCSP6, 0.80x1.20
(Pb-Free / Halogen Free)
5000 / Tape & Reel
† For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel
Packaging Specifications Brochure, BRD8011/D. http://www.onsemi.com/pub_link/Collateral/BRD8011-D.PDF
* I2C Bus is a trademark of Philips Corporation.
ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries
in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other
intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON
Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or
guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or
use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is
responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or
standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON
Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters,
including “Typicals” must be validated for each customer application by customer’s technical experts. ON Semiconductor does not convey any license under its
patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support
systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for
implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall
indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or
unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an
Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
www.onsemi.com
17