TSC GBL08 Single phase 4.0 amps. glass passivated bridge rectifier Datasheet

GBL005 THRU GBL10
Single Phase 4.0 AMPS. Glass Passivated Bridge Rectifiers
Voltage Range
50 to 1000 Volts
Current
4.0 Amperes
GBL
Features
Glass passivated chip junction
Ideal for printed circuit board
High case dielectric strength
Plastic material has Underwriters Laboratory
Flammability Classification 94V-0
Typical IR less than 0.1µA
High surge current capability
High temperature soldering guaranteed:
260OC / 10 seconds / .375”, (9.5mm) lead
lengths.
C2.5
.047(1.20)
.031(0.80)
.106(2.70)
.091(2.30)
.551(14.0)
.512(13.0)
.024(0.60)
.016(0.40)
1
Case: Molded plastic body.
Terminals: Plated leads solderable per
MIL-STD-750, Method 2026.
Weight: 0. 071 ounce, 2.0 grams
Mounting position: Any
.445(11.3)
.421(10.7)
A C
.106(2.70)
.091(2.30)
.067(1.70)
.051(1.30)
.043(1.10)
.035(0.90)
Mechanical Data
.142(3.60)
.130(3.30)
.799(20.3)
.776(19.7)
2
3
4
205(5.20) .205(5.20) .205(5.20)
189(4.80) .189(4.80) .189(4.80)
1
2
3
4
Dimensions in inches and (millimeters)
Maximum Ratings and Electrical Characteristics
Rating at 25℃ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%
Symbol GBL GBL
Type Number
005
01
Maximum Recurrent Peak Reverse Voltage
50
100
VRRM
Maximum RMS Voltage
35
70
VRMS
Maximum DC Blocking Voltage
100
50
VDC
Maximum Average Forward Rectified
Current
@TC = 50℃ (Note 1)
@TA = 40℃ (Note 2)
Peak Forward Surge Current, 8.3 ms Single
Half Sine-wave Superimposed on Rated
Load (JEDEC method ) TJ=150℃
Maximum Instantaneous Forward Voltage
@ 4.0A
Maximum DC Reverse Current @ TA=25℃
at Rated DC Blocking Voltage @ TA=125℃
GBL GBL GBL GBL GBL Units
02
04
06
08
10
200 400 600 800 1000
V
140 280 420 560 700
V
200 400 600 800 1000
V
I(AV)
4.0
3.0
A
IFSM
150
A
VF
1.00
V
5.0
500
22
3.5
uA
uA
IR
Typical Thermal Resistance Per Leg (Note 1)
(Note 2)
Typical Junction Capacitance Per Leg at
4.0V, 1MHz
Operating Temperature Range
RθJA
RθJL
TJ
-55 to +150
Storage Temperature Range
TSTG
-55 to + 150
Cj
95
℃/W
40
Notes 1. Unit Mounted on 2” x 3” x 0.25” Al. plate.
2. Units Mounted on P.C.B. 0.5” x 0.5“ (12x12mm) Copper Pads, 0.375” (9.5mm)
Lead Length.
- 728 -
pF
℃
℃
RATINGS AND CHARACTERISTIC CURVES (GBL005 THRU GBL10 )
FIG.1- DERATING CURVE FOR OUTPUT RECTIFIED
CURRENT
FIG.2-MAXIMUM NON-REPETITIVE PEAK FORWARD
SURGE CURRENT PER LEG
150
60 Hz Resistive or Inductive Load
O
Heat-Sink Mounting
2.0 x 3.0 x 0.25"
Aluminum Substrate
4.0
3.0
2.0
P.C.B. Mounting
0.47 x 0.47" (12 x 12mm)
Copper pads with 0.375"
(9.5mm) lead length
1.0
Tj=40 C
Single Half Sine-Wave
(JEDEC Method)
PEAK FORWARD SURGE CURRENT. (A)
AVERAGE FORWARD RECTIFIED CURRENT. (A)
5.0
100
50
1 Cycle
0
0
0
50
100
150
10
1
O
FIG.4- TYPICAL REVERSE LEAKAGE
CHARACTERISTICS PER LEG
FIG.3- TYPICAL FORWARD VOLTAGE
CHARACTERISTICS PER LEG
INSTANTANEOUS REVERSE LEAKAGE CURRENT. (mA)
INSTANTANEOUS FORWARD CURRENT. (A)
100
10
1
0.1
Tj=25 C
Pulse Width=300ms
1% Duty Cycle
0.01
0.4
500
100
50
600
1
400V
1000V
0.1
Tj=25 0C
0.01
0.6
0.8
1.0
1.2
INSTANTANEOUS FORWARD VOLTAGE. (V)
1.4
1.6
0
80
20
40
60
PERCENT OF RATED PEAK REVERSE VOLTAGE. (%)
100
FIG.6- TYPICAL TRANSIENT THERMAL
CHARACTERISTICS
100
TRANSIENT THERMAL IMPEDANCE ( C/W)
1000
Tj=25 C
JUNCTION CAPACITANCE (pF)
Tj=125 0C
10
FIG.5- TYPICAL JUNCTION CAPACTITANCE
PER LEG
f = 1 MHz
Vsig = 50mVp-p
100
50
600
10
0.1
100
NUMBER OF CYCLES
AMBIENT TEMPERATURE. ( C)
400V
1000V
1
10
REVERSE VOLTAGE. (V)
100
- 729 -
10
1
0.1
0.01
0.1
1
T, HEATING TIME (SEC.)
10
100
Similar pages