ACPL-M50L, ACPL-054L, ACPL-W50L and ACPL-K54L Low Power, 1MBd Digital Optocoupler Data Sheet Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available; -xxxE denotes a lead-free product Description Features The ACPL-M50L (single-channel in SO-5 footprint), ACPL-054L (dual-channel in SO-8 footprint), ACPL-W50L (single-channel in stretched SO-6 footprint) and ACPLK54L (dual-channel in stretched SO-8 footprint) are low power, low-input current, 1MBd digital optocouplers. Wide supply voltage Vcc: 2.7V to 24V This digital optocouplers use an insulating layer between the light emitting diode and an integrated photon detector to provide electrical insulation between input and output. Separate connections for the photodiode bias and output transistor collector increase the speed up to a hundred times over that of a conventional photo-transistor coupler by reducing the base-collector capacitance. Compact SO-5, SO-8, stretched SO-6 and stretched SO-8 package Low Drive Current: 3mA Open-Collector Output TTL compatible 15 kV/s High Common-Mode Rejection at VCM = 1500 V Guaranteed performance from Temperature Range: -40°C to +105°C Low Propagation Delay: 1s max at 5V The ACPL-M50L/054L/W50L/K54L have an increased common mode transient immunity of 15kV/s minimum at VCM = 1500V over a temperature range of -40 to 105°C. The current transfer ratio (CTR) is 140% typical for ACPLM50L or 130% typical for ACPL-054L/W50L/K54L at IF = 3mA. This digital optocoupler can be use in any TTL/ CMOS, TTL/LSTTL or wide bandwidth analog applications. Worldwide Safety Approval: (Pending except ACPL-M50L) – UL1577 recognized, 3750Vrms/1min for ACPL-M50L/054L, 5000Vrms/1min for ACPL-W50L/K54L, – CSA Approval – IEC 60747-5-5, IEC/EN/DIN EN 60747-5-2 Functional Diagram Applications 6 VCC Anode 1 5 VO Cathode 3 4 GND ACPL-M50L 6 VCC 2 5 VO Micro-controller Interface 4 GND Feedback Elements in Switching Power Supplies NC Cathode 3 Digital Signal Isolation Digital isolation for A/D, D/A conversion Digital field ACPL-W50L Anode1 1 8 VCC Cathode1 2 7 VO1 Cathode2 3 6 VO2 Anode2 4 Communications Interface Anode 1 5 GND Truth Table LED Vo ON LOW OFF HIGH ACPL-054L/K54L The connection of a 0.1 F bypass capacitor between pins 4 and 6 for ACPL-M50L/W50L and between pins 5 and 8 for ACPL-054L/K54L is recommended. CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD. Ordering Information ACPL-M50L and ACPL-054L are UL Recognized with 3750 Vrms for 1 minute per UL1577. ACPL-W50L and ACPL-K54L are UL Recognized with 5000 Vrms for 1 minute per UL1577 Options Part Number RoHS Compliant Package Surface Mount ACPL-M50L -000E SO-5 X ACPL-054L X -500E X X -560E X X -000E SO-8 X X X X X X 100 per tube 1500 per reel X X X X X X -060E 1500 per reel 1500 per reel 100 per tube -560E Stretched SO-8 X X -500E -000E 100 per tube 100 per tube -500E Stretched SO-6 Quantity 1500 per reel X X -060E ACPL-K54L X -060E -000E IEC 60747-5-5, IEC/EN/DIN EN 60747-5-2 100 per tube -060E -560E ACPL-W50L Tape & Reel 100 per tube 1000 per reel X X 1000 per reel 80 per tube X X -500E X X -560E X X 80 per tube 1000 per reel X 1000 per reel To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Example 1: ACPL-M50L-500E to order product of Mini-flat Surface Mount 5-pin package in Tape and Reel packaging with RoHS compliant. Option datasheets are available. Contact your Avago sales representative or authorized distributor for information. 2 Package Outline Drawings ACPL-M50L Small Outline SO-5 Package (JEDEC MO-155) ANODE M50L YWW 4.4 ± 0.1 (0.173 ± 0.004) 1 7.0 ± 0.2 (0.276 ± 0.008) CATHODE 3 6 VCC 5 VOUT 4 GND 0.4 ± 0.05 (0.016 ± 0.002) 3.6 ± 0.1* (0.142 ± 0.004) 0.102 ± 0.102 (0.004 ± 0.004) 2.5 ± 0.1 (0.098 ± 0.004) 0.216 ± 0.038 (0.0085 ± 0.0015) Dimensions in Millimeters (Inches) * Maximum mold flash on each side is 0.15 mm (0.006) Note: Floating lead protrusion is 0.15 mm (6 mils) max. MAX. LEAD COPLANARITY = 0.102 (0.004) Land Pattern Recommendation 4.4 (0.17) 1.3 (0.05) 2.5 (0.10) 1.8 (0.072) 8.27 (0.325) Dimension in Millimeters (Inches) 3 7° MAX. 0.71 (0.028) MIN 1.27 BSC (0.050) 0.64 (0.025) ACPL-054L (Small Outline S0-8 Package) LEAD FREE 8 7 6 5 x54LV YWW 3.937 ± 0.127 (0.155 ± 0.005) LAND PATTERN RECOMMENDATION 5.994 ± 0.203 (0.236 ± 0.008) TYPE NUMBER (‘V’ for OPTION 060) 7.49 (0.295) DATE CODE PIN ONE 1 2 3 4 0.406 ± 0.076 (0.016 ± 0.003) 1.9 (0.075) 1.270 BSC (0.050) 0.64 (0.025) * 5.080 ± 0.127 (0.200 ± 0.005) 7° 3.175 ± 0.127 (0.125 ± 0.005) 1.524 (0.060) 45° X 0.432 (0.017) 0 ~ 7° * Total package length (inclusive of mold flash) 5.207 ± 0.254 (0.205 ± 0.010) Dimensions in Millimeters (Inches). Lead coplanarity = 0.10 mm (0.004 inches) max. Option number 500 not marked. 0.228 ± 0.025 (0.009 ± 0.001) 0.203 ± 0.102 (0.008 ± 0.004) 0.305 MIN. (0.012) Note: Floating lead protrusion is 0.15 mm (6 mils) max. ACPL-W50L Stretched SO-6 Package 4.480±0.254 (0.0180±0.010) LAND PATTERN RECOMMENDATION 1.27 (0.050) BSG 6 5 12.65 (0.498) 4 ROHS-COMPLIANCE INDICATOR 0.76 (0.030) PART NUMBER W50L YWW DATE CODE 1.91 (0.075) 1 2 3 0.381±0.127 (0.015±0.005) 7° +0.127 0 0.268 +0.005 - 0.000 6.807 ( 0.45 (0.018) 7° 4 0.750±0.250 (0.0295±0.010) 1.590±0.127 (0.063±0.005) 45° 3.180±0.127 (0.125±0.005) 0.20±0.10 (0.008±0.004) Dimensions in Millimeters (Inches). Lead coplanarity = 0.1 mm (0.004 inches). ) 11.50±0.250 (0.453±0.010) ACPL-K54L Stretched SO-8 Package 5.850±0.254 (0.230±0.010) 1.270 (0.050) BSG 8 7 6 LAND PATTERN RECOMMENDATION 5 ROHS-COMPLIANCE INDICATOR PART NUMBER K54L YWW DATE CODE 1.905 (0.1) 1 2 7° 3 12.650 (0.5) 4 0.381±0.13 (0.015±0.005) 0.450 (0.018) 7° 1.590±0.127 (0.063±0.005) 45° 3.180±0.127 (0.125±0.005) 0.200±0.100 (0.008±0.004) 0.750±0.250 (0.0295±0.010) Dimensions in Millimeters (Inches). Lead coplanarity = 0.1 mm (0.004 inches). 6.807±0.127 (0.268±0.005) 11.5±0.250 (0.453±0.010) Solder Reflow Profile Recommended reflow condition as per JEDEC Standard, J-STD-020 (latest revision). Non-Halide Flux should be used. Regulatory Information The ACPL-M50L/054L/W50L/K54L will be approved by the following organizations: UL Approval under UL 1577, component recognition program up to VISO = 3750 VRMS for ACPL-M50L/054L and VISO = 5000 VRMS for ACPL-W50L/K54L. CSA Approval under CSA Component Acceptance Notice #5. IEC 60747-5-5, IEC/EN/DIN EN 60747-5-2 (Option 060E only) 5 Insulation and Safety Related Specifications Parameter Symbol ACPL-M50L ACPL-054L ACPL-W50L ACPL-K54L Units Conditions Minimum External Air Gap (Clearance) L(101) 5 4.9 8 mm Measured from input terminals to output terminals, shortest distance through air. Minimum External Tracking (Creepage) L(102) 5 4.8 8 mm Measured from input terminals to output terminals, shortest distance path along body. 0.08 0.08 0.08 mm Through insulation distance conductor to conductor, usually the straight line distance thickness between the emitter and detector. 175 175 175 Volts DIN IEC 112/VDE 0303 Part 1 IIIa IIIa IIIa Minimum Internal Plastic Gap (Internal Clearance) Tracking Resistance (Comparative Tracking Index) CTI Isolation Group Material Group (DIN VDE 0110, 1/89, Table 1) IEC 60747-5-5, IEC/EN/DIN EN 60747-5-2 Insulation Characteristics* (Option 060E) Symbol Description Installation classification per DIN VDE 0110/39, Table 1 for rated mains voltage ≤ 150 Vrms for rated mains voltage ≤ 300 Vrms for rated mains voltage ≤ 600 Vrms for rated mains voltage ≤ 1000 Vrms Characteristic Unit ACPL-M50L/ 054L ACPL-W50L/ K54L I – IV I – III I – II I – IV I – IV I – III I – III Climatic Classification 55/105/21 55/105/21 Pollution Degree (DIN VDE 0110/39) 2 2 Maximum Working Insulation Voltage VIORM 560 1140 Vpeak Input to Output Test Voltage, Method b* VIORM x 1.875 = VPR, 100% Production Test with tm = 1 sec, Partial discharge < 5 pC VPR 1050 2137 Vpeak Input to Output Test Voltage, Method a* VIORM x 1.6 = VPR, Type and Sample Test, tm = 10 sec, Partial discharge < 5 pC VPR 896 1824 Vpeak Highest Allowable Overvoltage (Transient Overvoltage tini = 60 sec) VIOTM 6000 8000 Vpeak Safety-limiting values – maximum values allowed in the event of a failure. Case Temperature Input Current** Output Power** TS IS, INPUT PS, OUTPUT 150 150 600 175 230 600 °C mA mW Insulation Resistance at TS, VIO = 500 V RS >109 >109 * Refer to the optocoupler section of the Isolation and Control Components Designer’s Catalog, under Product Safety Regulations section, (IEC 60747-5-5, IEC/EN/DIN EN 60747-5-2) for a detailed description of Method a and Method b partial discharge test profiles. ** Refer to the following figure for dependence of PS and IS on ambient temperature. 6 Absolute Maximum Ratings Parameter Symbol Min. Max. Units Storage Temperature TS -55 125 °C Operating Temperature TA -40 105 °C 260 °C Lead Soldering Cycle Temperature 10 s Average Forward Input Current[1] Time IF(avg) 20 mA Peak Forward Input Current[2] (50% duty cycle, 1ms pulse width) IF(peak) 40 mA Peak Transient Input Current (≤1s pulse width, 300ps) IF(trans) 1 A Reversed Input Voltage VR 5 V Input Power Dissipation[3] PIN 36 mW Output Power Dissipation[4] PO 45 mW Average Output Current IO(AVG) 8 mA Peak Output Current IO(PEAK) 16 mA Supply Voltage VCC -0.5 30 V Output Voltage VO -0.5 24 V Solder Reflow Temperature Profile See Package Outline Drawings section Notes: 1. Derate linearly above 85°C free-air temperature at a rate of 0.5 mA/°C. 2. Derate linearly above 85°C free-air temperature at a rate of 1.0 mA/°C. 3. Derate linearly above 85°C free-air temperature at a rate of 0.9 mW/°C. 4. Derate linearly above 85°C free-air temperature at a rate of 1.2 mW/°C. Recommended Operating Conditions Parameter Symbol Min. Max. Units Supply Voltage VCC 2.7 24 V Input Current, High Level IFH 3 10 mA Operating Temperature TA -40 105 °C Forward Input Voltage (OFF) VF(OFF) 0.8 V 7 Electrical Specifications (DC) Over recommended operating TA = -40°C to 105°C, supply voltage (2.7V ≤ VCC ≤ 24V) and unless otherwise specified. All typicals are at TA=25°C Parameter Sym. Part Number Min. Typ. Max. Units Conditions Current Transfer Ratio CTR[1] ACPL-M50L 100 140 200 % TA = 25°C ACPL-054L ACPL-W50L ACPL-K54L 93 130 200 80 Logic Low Output Voltage VOL Logic High Output Current IOH 53 VO=0.4V VO=0.5V % % Fig. TA = 25°C VO=0.4V VO=0.5V % 0.2 0.4 V TA = 25°C IO=3mA 0.2 0.5 V 0.003 0.5 A 0.01 1 VO=VCC=24V 80 VO=VCC=24V IO=1.6mA TA = 25°C VO=VCC=5.5V Logic Low Supply Current per Channel ICCL 36 100 A IF=3mA, VO=open, VCC=24V Logic High Supply Current per Channel ICCH 0.02 2 A IF=0mA, VO=open, VCC=24V Input Forward Voltage VF 1.5 1.8 V 1.5 1.95 Input Reversed Breakdown Voltage BVR Temperature Coefficient of Forward Voltage VF/ TA Input Capacitance CIN TA=25°C IF=3mA V IF=3mA V IR=10A -1.6 mV/°C IF=3mA 77 pF F = 1MHz, VF = 0 5 VCC=3.3V or 5V IF=3mA 2,3 VCC=3.3V or 5V IF=3mA 2,3 VCC=3.3V or 5V IF=3mA IF=0mA 4,5 1 Notes: 1. CURRENT TRANSFER RATIO in percent is defined as the ratio of output collector current, IO, to the forward LED input current, IF, times 100%. 8 Switching Specifications (ACPL-M50L) Over recommended operating (TA = -40°C to 105°C), IF = 3mA, (2.7V ≤ VCC ≤ 24V), unless otherwise specified. Parameter Symbol Min Propagation Delay Time to TPHL Logic Low at Output Propagation Delay Time to TPLH Logic High at Output Pulse Width Distortion[1] Propagation Delay Difference Between Any two Parts[2] PWD tpsk Typ Max Units Test Conditions Fig. 0.2 0.5 s TA=25°C 14 0.2 1 s Pulse: f=10kHz, Duty cycle=50%, IF= 3mA, VCC=3.3 V, RL=1.2k, CL=15pF, V THHL=1.5V 0.22 0.5 s 14 0.22 1 s Pulse: f=10kHz, Duty cycle=50%, IF= 3mA, VCC=5.0 V, RL=1.9k, CL=15pF, V THHL=1.5V 0.33 0.7 s 14 0.33 1.3 s Pulse: f=10kHz, Duty cycle=50%, IF= 3mA, VCC=24V, RL=10k, CL=15pF, V THHL=1.5V 0.38 0.8 s 14 0.38 1.2 s Pulse: f=10kHz, Duty cycle=50%, IF= 3mA, VCC=3.3 V, RL=1.2k, CL=15pF, V THHL=2.0V 0.31 0.7 s 14 0.31 1 s Pulse: f=10kHz, Duty cycle=50%, IF= 3mA, VCC=5.0 V, RL=1.9k, CL=15pF, V THHL=2.0V 0.3 0.7 s 14 0.3 1 s Pulse: f=10kHz, Duty cycle=50%, IF= 3mA, VCC=24V, RL=10k, CL=15pF, V THHL=2.0V 0.18 0.8 s 14 0.18 1.2 s Pulse: f=10kHz, Duty cycle=50%, IF= 3mA, VCC=3.3 V, RL=1.2k, CL=15pF, V THHL=1.5V, V THLH=2.0V 0.1 0.7 s 14 0.1 1 s Pulse: f=10kHz, Duty cycle=50%, IF= 3mA, VCC=5.0V, RL=1.9k, CL=15pF, V THHL=1.5V, V THLH=2.0V 0.1 0.7 s 1 s Pulse: f=10kHz, Duty cycle=50%, IF= 3mA, VCC=24V, RL=10k, CL=15pF, V THHL=1.5V, V THLH=2.0V 14 0.1 0.18 0.7 s TA=25°C Pulse: f=10kHz, Duty cycle=50%, IF= 3mA, VCC=3.3 V , RL=1.2k, CL=15pF, V THHL=1.5V, V THLH=2.0V 0.1 0.6 s TA=25°C Pulse: f=10kHz, Duty cycle=50%, IF= 3mA, VCC=5.0V, RL=1.9k, CL=15pF, V THHL=1.5V, V THLH=2.0V 0.1 0.6 s TA=25°C Pulse: f=10kHz, Duty cycle=50%, IF= 3mA, VCC=24V, RL=10k, CL=15pF, V THHL=2.0V TA=25°C TA=25°C TA=25°C TA=25°C TA=25°C TA=25°C TA=25°C TA=25°C 6a, 14 7a, 14 8a, 14 6a, 14 7a, 14 8a, 14 14 14 14 Common Mode Transient Immunity at Logic High Output[3] |CMH| 15 25 kV/s VCM=1500V, IF=0mA, TA=25°C, RL=1.2k or 1.9k, VCC=3.3 V or 5V 15 Common Mode Transient Immunity at Logic Low Output[4] |CML| 15 20 kV/s VCM=1500V, IF=3mA, TA=25°C, RL=1.2k, VCC=5V 15 10 15 kV/s VCM=1500V, IF=3mA, TA=25°C, RL=1.2k, VCC=3.3 V 15 9 Switching Specifications (ACPL-054L/W50L/K54L) Over recommended operating (TA = -40°C to 105°C), IF = 3mA, (2.7V ≤ VCC ≤ 24V), unless otherwise specified. Parameter Symbol Min Propagation Delay Time to TPHL Logic Low at Output Propagation Delay Time to TPLH Logic High at Output Pulse Width Distortion[1] Propagation Delay Difference Between Any two Parts[2] PWD tpsk Typ Max Units Test Conditions Fig. 0.2 0.5 s TA=25°C 14 0.2 1 s Pulse: f=10kHz, Duty cycle=50%, IF=3mA, VCC=3.3 V, RL= 1.8k, CL=15pF, V THHL=1.5V 0.22 0.5 s 14 0.22 1 s Pulse: f=10kHz, Duty cycle=50%, IF=3mA, VCC=5.0 V, RL= 2.9k, CL=15pF, V THHL=1.5V 0.33 0.7 s 14 0.33 1.3 s Pulse: f=10kHz, Duty cycle=50%, IF=3mA, VCC=24V, RL=14.8k, CL=15pF, V THHL=1.5V 0.38 0.8 s 14 0.38 1.4 s Pulse: f=10kHz, Duty cycle=50%, IF=3mA, VCC=3.3 V, RL=1.8k, CL=15pF, V THHL=2.0V 0.31 0.7 s 14 0.31 1 s Pulse: f=10kHz, Duty cycle=50%, IF=3mA, VCC=5.0 V, RL=2.9k, CL=15pF, V THHL=2.0V 0.3 0.7 s 14 0.3 1 s Pulse: f=10kHz, Duty cycle=50%, IF=3mA, VCC=24V, RL=14.8k, CL=15pF, V THHL=2.0V 0.18 0.8 s 14 0.18 1.4 s Pulse: f=10kHz, Duty cycle=50%, IF=3mA, VCC=3.3 V, RL=1.8k, CL=15pF, V THHL=1.5V, V THLH=2.0V 0.1 0.7 s 14 0.1 1 s Pulse: f=10kHz, Duty cycle=50%, IF=3mA, VCC=5.0V, RL = 2.9k, CL=15pF, V THHL=1.5V, V THLH=2.0V 0.1 0.7 s 1 s Pulse: f=10kHz, Duty cycle=50%, IF=3mA, VCC=24V, RL=14.8k, CL=15pF, V THHL=1.5V, V THLH=2.0V 14 0.1 0.18 0.7 s TA=25°C Pulse: f=10kHz, Duty cycle=50%, IF=3mA, VCC=3.3 V, RL=1.8k, CL=15pF, V THHL=1.5V, V THLH=2.0V 0.1 0.6 s TA=25°C Pulse: f=10kHz, Duty cycle=50%, IF=3mA, VCC=5.0V, RL=2.9k, CL=15pF, V THHL=1.5V, V THLH=2.0V 0.1 0.6 s TA=25°C Pulse: f=10kHz, Duty cycle=50%, IF=3mA, VCC=24V, RL=14.8k, CL=15pF, V THHL=1.5V, V THLH=2.0V TA=25°C TA=25°C TA=25°C TA=25°C TA=25°C TA=25°C TA=25°C TA=25°C 6b, 14 7b, 14 8b, 14 6b, 14 7b, 14 8b, 14 14 14 14 Common Mode Transient Immunity at Logic High Output[3] |CMH| 15 25 kV/s VCM=1500V, IF=0mA, TA=25°C, RL=1.8k or 2.9k, VCC=3.3 V or 5V 15 Common Mode Transient Immunity at Logic Low Output[4] |CML| 15 20 kV/s VCM=1500V, IF=4mA, TA=25°C, RL=2.9k, VCC=5V 15 15 20 kV/s VCM=1500V, IF=3mA, TA=25°C, RL=1.8k, VCC=3.3 V 15 Notes: 1. Pulse Width Distortion (PWD) is defined as |tPHL - tPLH| for any given device. 2. The difference between tPLH and tPHL between any two parts under the same test condition. (See IPM Dead Time and Propagation Delay Specifications section.) 3. Common transient immunity in a Logic High level is the maximum tolerable (positive) dVCM/dt on the rising edge of the common mode pulse, VCM, to assure that the output will remain in a Logic High state (i.e., VO > 2.0 V). 4. Common mode transient immunity in a Logic Low level is the maximum tolerable (negative) dVCM/dt on the falling edge of the common mode pulse signal, VCM to assure that the output will remain in a Logic Low state (i.e., VO < 0.8 V). 10 Package Characteristics All Typical at TA = 25°C. Parameter Symbol Part Number Min. Input-Output Momentary Withstand Voltage [1,2] VISO ACPL-M50L/054L 3750 ACPL-W50L/K54L 5000 Input-Output Resistance [1] RI-O Input-Output Capacitance [1] Typ. Max. Units Test Conditions Vrms RH ≤ 50%, t = 1 min., TA = 25°C 1014 VI-O = 500 Vdc CI-O 0.6 pF f = 1 MHz, TA = 25°C Input-Input Insulation Leakage Current[3] II-I 0.005 A RH ≤ 45%, t = 5 s VI-I = 500Vdc Input-Input Resistance [3] RI-I 1011 Input-Input Capacitance [3] CI-I 0.25 pF f = 1 MHz Notes: 1. Device considered a two terminal device: pins 1 and 3 shorted together and pins 4, 5 and 6 shorted together for ACPL-M50L, pins 1, 2, 3 and 4 shorted together and pins 5, 6, 7 and 8 shorted together for ACPL-054L/K54L, pins 1, 2 and 3 shorted together and pins 4, 5 and 6 shorted together for ACPL-W50L. 2. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 VRMS for 1 second for ACPL-M50L/054L and ≥ 6000 VRMS for 1 second for ACPL-W50L/K54L (leakage detection current limit, II-O ≤ 5 A). 3. Measured between pins 1 and 2 shorted together and pins 3 and 4 shorted together for ACPL-054L/K54L. 11 NORMALIZED CURRENT TRANSFER RATIO IF - FORWARD CURRENT - mA 100 TA = 25°C 10 1 0.1 IF 0.01 VF 0.001 0.0001 1.1 1.2 1.3 1.4 1.5 VF - FORWARD VOLTAGE - V 1.6 1.7 1.1 1 0.9 0.8 NORMALIZED IF = 3 mA VO = 0.4 V VCC = 5 V 0.7 0.6 -50 -25 0 25 50 75 100 125 0.8 0.7 0.6 -50 NORMALIZED IF = 3 mA VO = 0.4 V VCC = 3.3 V -25 0 25 50 75 TA - TEMPERATURE - °C 100 125 IF = 0 mA VO = VCC = 5 V 10 1 0.1 0.01 -60 -40 -20 0 20 40 IF = 0 mA VO = VCC = 3.3 V 10 1 0.1 0.01 -60 -40 -20 0 20 40 60 80 Figure 4. Typical Logic High Output Current vs. Temperature 1000 100 100 TA - TEMPERATURE - °C Figure 3. Typical Current Transfer Ratio vs. Temperature IOH - LOGIC HIGH OUTPUT CURRENT - nA 0.9 1000 TA - TEMPERATURE - °C 60 80 TA - TEMPERATURE - °C Figure 5. Typical Logic High Output Current vs. Temperature 12 1 Figure 2. Typical Current Transfer Ratio vs. Temperature IOH - LOGIC HIGH OUTPUT CURRENT - nA NORMALIZED CURRENT TRANSFER RATIO Figure 1. Input Current vs. Forward Voltage 1.1 100 120 100 120 700 600 800 IF = 3 mA, VCC = 3.3 V RL = 1.9 kΩ RL = 1.2 kΩ 500 700 tp - PROPAGATION DELAY - ns tp - PROPAGATION DELAY - ns 800 tPLH 400 tPHL 300 200 100 0 -60 -40 -20 0 20 40 60 TA - TEMPERATURE - °C 80 100 tp - PROPAGATION DELAY - ns tp - PROPAGATION DELAY - ns tPHL 200 100 -40 -20 0 20 40 60 TA - TEMPERATURE - °C 80 100 -20 0 20 40 60 TA - TEMPERATURE - °C 80 100 120 80 100 120 80 100 120 IF = 3 mA, VCC = 5 V RL = 2.9 kΩ 600 500 tPLH tPHL 400 300 200 0 -60 120 -40 -20 0 20 40 60 TA - TEMPERATURE - °C Figure 7b. Typical Propagation Delay vs. Temperature (ACPL-054L/W50L/K54L) 600 IF = 3 mA, VCC = 24 V RL = 20 kΩ RL = 10 kΩ 400 tp - PROPAGATION DELAY - ns 600 tp - PROPAGATION DELAY - ns -40 100 Figure 7a. Typical Propagation Delay vs. Temperature (ACPL-M50L) tPHL tPLH 300 200 100 -40 -20 0 20 40 60 TA - TEMPERATURE - °C 80 100 Figure 8a. Typical Propagation Delay vs. Temperature (ACPL-M50L) 13 200 700 tPLH 300 0 -60 tPHL 300 800 400 500 tPLH 400 Figure 6b. Typical Propagation Delay vs. Temperature (ACPL-054L/W50L/K54L) IF = 3 mA, VCC = 5 V RL = 4.1 kΩ RL = 1.9 kΩ 500 0 -60 500 0 -60 120 800 600 600 100 Figure 6a. Typical Propagation Delay vs. Temperature (ACPL-M50L) 700 IF = 3 mA, VCC = 3.3 V RL = 1.8 kΩ 120 500 IF = 3 mA, VCC = 24 V RL = 14.8 kΩ 400 tPHL tPLH 300 200 100 0 -60 -40 -20 0 20 40 60 TA - TEMPERATURE - °C Figure 8b. Typical Propagation Delay vs. Temperature (ACPL-054L/W50L/K54L) 1600 tp - PROPAGATION DELAY - ns 1400 1200 tp - PROPAGATION DELAY - ns IF = 3 mA, VCC = 3.3 V IF = 10 mA IF = 3 mA 1000 800 tPLH 600 tPHL 400 1000 900 800 200 0 1 10 IF = 3 mA, VCC = 5 V IF = 10 mA IF = 3 mA 700 600 500 400 300 200 100 0 tPLH tPHL 1 10 RL - LOAD RESISTANCE - kΩ Figure 9. Typical Propagation Delay vs. Load Resistance Figure 10. Typical Propagation Delay vs. Load Resistance 2600 2400 2200 2000 1800 1600 1400 1200 1000 800 600 400 200 0 IF = 3 mA, VCC = 24 V RL = 10 kΩ, TA = 25°C tp - PROPAGATION DELAY - ns tp - PROPAGATION DELAY - ns RL - LOAD RESISTANCE - kΩ tPLH tPHL 0 100 200 300 400 CL - LOAD CAPACITANCE - pF 500 Figure 11a. Typical Propagation delay vs. Load Capacitance (ACPL-M50L) IF = 3 mA RL = 10 kΩ TA = 25°C 2000 tp - PROPAGATION DELAY - ns tp - PROPAGATION DELAY - ns tPHL tPLH 0 100 200 300 400 CL - LOAD CAPACITANCE - pF 500 2500 1500 1000 tPLH 500 8 10 tPHL 14 12 16 18 VCC - SUPPLY VOLTAGE - V 20 22 Figure 12a. Typical Propagation Delay vs. Supply Voltage (ACPL-M50L) 14 IF = 3 mA, VCC = 24 V RL = 14.8 kΩ, TA = 25°C Figure 11b. Typical Propagation delay vs. Load Capacitance (ACPL-054L/W50L/K54L) 2500 0 2600 2400 2200 2000 1800 1600 1400 1200 1000 800 600 400 200 0 24 IF = 3 mA RL = 14.8 kΩ TA = 25°C 2000 1500 1000 tPLH 500 0 8 10 tPHL 12 14 16 18 VCC - SUPPLY VOLTAGE - V Figure 12b. Typical Propagation Delay vs. Supply Voltage (ACPL-054L/W50L/K54L) 20 22 24 600 VCC = 24 V RL = 10 kΩ TA = 25°C 500 tp - PROPAGATION DELAY - ns tp - PROPAGATION DELAY - ns 600 400 300 tPLH 200 tPHL 100 0 0 5 10 15 IF - FORWARD LED CURRENT - mA Figure 13a. Typical Propagation Delay vs. Supply Current (ACPL-M50L) IF PULSE GEN. Z O = 50 Ω t r = 5 ns 0 V CC VO V THHL tPLH 300 200 tPHL 100 0 5 10 15 IF - FORWARD LED CURRENT - mA Figure 13b. Typical Propagation Delay vs. Supply Current (ACPL-054L/W50L/K54L) IF 1 V CC 6 RL VO 5 0.1μF V THLH V OL t PHL 400 0 20 VCC = 24 V RL = 14.8 kΩ TA = 25°C 500 3 IF MONITOR 4 CL RM t PLH Figure 14. Switching Test Circuits V CM 0V 10 V 90% 10% tr VO IF 90% 10% tf RL 3 4 V FF V OL CL V CM + – PULSE GEN. Figure 15. Test Circuit for Transient Immunity and typical waveforms 15 VO 5 0.1μF V CC SWITCH AT B: IF = 3 mA V CC 6 B SWITCH AT A: I F = 0 mA VO 1 A 20 40 200 IO - OUTPUT CURRENT - mA CTR - CURRENT TRANSFER RATIO - % 250 VO = 0.4 V VCC = 5 V 150 100 50 0 0 5 10 15 IF - FORWARD CURRENT - mA Figure 16. Current Transfer Ratio versus Input Current 20 25 TA = 25 oC VCC = 5 V 30 20 10 - 0 4 8 12 16 VO - OUTPUT VOLTAGE - V Figure 17. DC Pulse Transfer Characteristic For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2011 Avago Technologies. All rights reserved. AV02-2223EN - October 25, 2011 IF = 20 mA IF = 15 mA IF = 10 mA IF = 5 mA 20 24