HANBit HMN1288D Non-Volatile SRAM MODULE 1Mbit (128K x 8-Bit), 32Pin-DIP, 5V Part No. HMN1288D GENERAL DESCRIPTION The HMN1288D Nonvolatile SRAM is a 1,048,576-bit static RAM organized as 131,072 bytes by 8 bits. The HMN1288D has a self-contained lithium energy source provide reliable non-volatility coupled with the unlimited write cycles of standard SRAM and integral control circuitry, which constantly monitors the single 5V, supply for an out-oftolerance condition. When such a condition occurs, the lithium energy source is automatically switched on to sustain the memory until after VCC returns valid and write protection is unconditionally enabled to prevent garbled data. In addition the SRAM is unconditionally write-protected to prevent an inadvertent write operation. At this time the integral energy source is switched on to sustain the memory until after VCC returns valid. The HMN1288D uses extremely low standby current CMOS SRAM’s, coupled with small lithium coin cells to provide nonvolatility without long write-cycle times and the write-cycle limitations associated with EEPROM. FEATURES w Access time : 70, 85, 120, 150 ns PIN ASSIGNMENT w High-density design : 1Mbit Design w Battery internally isolated until power is applied NC w Industry-standard 32-pin 128K x 8 pinout A16 A14 A12 A7 A6 A5 A4 A3 A2 A1 A0 DQ0 DQ1 DQ2 VSS w Unlimited write cycles w Data retention in the absence of VCC w 10-years minimum data retention in absence of power w Automatic write-protection during power-up/power-down cycles w Data is automatically protected during power loss w Conventional SRAM operation; unlimited write cycles OPTIONS MARKING 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 VCC A15 NC /WE A13 A8 A9 A11 /OE A10 /CE DQ7 DQ6 DQ5 DQ4 DQ3 32-pin Encapsulated Package w Timing 70 ns - 70 85 ns - 85 120 ns -120 150 ns -150 URL : www.hbe.co.kr Rev. 1.0 (June, 2002) 1 HANBit Electronics Co.,Ltd HANBit HMN1288D FUNCTIONAL DESCRIPTION The HMN1288D executes a read cycle whenever /WE is inactive(high) and /CE is active(low). The address specified by the address inputs(A0-A16) defines which of the 131,072 bytes of data is accessed. Valid data will be available to the eight data output drivers within tACC (access time) after the last address input signal is stable. When power is valid, the HMN1288D operates as a standard CMOS SRAM. During power-down and power-up cycles, the HMN1288D acts as a nonvolatile memory, automatically protecting and preserving the memory contents. The HMN1288D is in the write mode whenever the /WE and /CE signals are in the active (low) state after address inputs are stable. The later occurring falling edge of /CE or /WE will determine the start of the write cycle. The write cycle is terminated by the earlier rising edge of /CE or /WE. All address inputs must be kept valid throughout the write cycle. /WE must return to the high state for a minimum recovery time (tWR) before another cycle can be initiated. The /OE control signal should be kept inactive (high) during write cycles to avoid bus contention. However, if the output bus been enabled (/CE and /OE active) then /WE will disable the outputs in tODW from its falling edge. The HMN1288D provides full functional capability for Vcc greater than 4.5 V and write protects by 4.37 V nominal. Powerdown/power-up control circuitry constantly monitors the VCC supply for a power-fail-detect threshold VPFD. When VCC falls below the VPFD threshold, the SRAM automatically write-protects the data. All inputs to the RAM become “don’t care” and all outputs are high impedance. As Vcc falls below approximately 3 V, the power switching circuit connects the lithium energy soure to RAM to retain data. During power-up, when Vcc rises above approximately 3.0 volts, the power switching circuit connects external Vcc to the RAM and disconnects the lithium energy source. Normal RAM operation can resume after Vcc exceeds 4.5 volts. BLOCK DIAGRAM /OE PIN DESCRIPTION /WE A0-A16 : Address Input A0-A16 128K x 8 SRAM Block DQ0-DQ7 /CE : Chip Enable Vss : Ground Power /CE /CE CON Power – Fail Control DQ0-DQ7 : Data In / Data Out /WE : Write Enable VCC /OE : Output Enable Lithium Cell VCC : Power (+5V) NC : No Connection URL : www.hbe.co.kr Rev. 1.0 (June, 2002) 2 HANBit Electronics Co.,Ltd HANBit HMN1288D TRUTH TABLE MODE /OE /CE /WE I/O OPERATION POWER Not selected X H X High Z Standby Output disable H L H High Z Active Read L L H DOUT Active Write X L L DIN Active SYMBOL RATING VCC -0.3V to 7.0V VT -0.3V to 7.0V VT≤ VCC+0.3 0 to 70°C Commercial -40 to 85°C Industrial ABSOLUTE MAXIMUM RATINGS PARAMETER DC voltage applied on VCC relative to VSS DC Voltage applied on any pin excluding VCC relative to VSS Operating temperature TOPR Storage temperature TSTG -55°C to 125°C Temperature under bias TBIAS -40°C to 85°C TSOLDER 260°C Soldering temperature CONDITIONS For 10 second NOTE: Permanent device damage may occur if Absolute Maximum Ratings are exceeded. Functional operation should be restricted to the Recommended DC Operating Conditions detailed in this data sheet. Exposure to higher than recommended voltage for extended periods of time could affect device reliability. RECOMMENDED DC OPERATING CONDITIONS ( TA= TOPR ) PARAMETER SYMBOL MIN TYPICAL MAX Supply Voltage VCC 4.5V 5.0V 5.5V Ground VSS 0 0 0 Input high voltage VIH 2.2 - Vcc+0.3V Input low voltage VIL -0.3 - 0.8V NOTE: Typical values indicate operation at TA = 25℃ URL : www.hbe.co.kr Rev. 1.0 (June, 2002) 3 HANBit Electronics Co.,Ltd HANBit HMN1288D DC ELECTRICAL CHARACTERISTICS (TA= TOPR, VCCmin £ VCC ≤ VCCmax ) PARAMETER Input Leakage Current Output Leakage Current CONDITIONS SYMBOL MIN TYP. MAX UNIT ILI - - ± 1 mA ILO - - ± 1 mA VIN=VSS to VCC /CE=VIH or /OE=VIH or /WE=VIL Output high voltage IOH=-1.0mA VOH 2.4 - - V Output low voltage IOL= 2.1mA VOL - - 0.4 V Standby supply current /CE=VIH ISB - 4 3 ISB1 - 2.5 100 mA ICC - 75 15 ㎃ Power-fail-detect voltage VPFD 4.30 4.37 4.50 V Supply switch-over voltage VSO - 3 - V ㎃ /CE≥ VCC-0.2V, Standby supply current 0V≤ VIN≤ 0.2V, or VIN≥ VCC-0.2V Operating supply current Min.cycle,duty=100%, /CE=VIL, II/O=0㎃ , NOTE: Typical values indicate operation at TA = 25℃ . CAPACITANCE (TA=25℃ , f=1MHz, VCC=5.0V) DESCRIPTION Input Capacitance Input/Output Capacitance CONDITIONS SYMBOL MAX MIN UNIT Input voltage = 0V CIN 10 - pF Output voltage = 0V CI/O 10 - pF CHARACTERISTICS (Test Conditions) PARAMETER Input pulse levels VALUE 0 to 3V Input rise and fall times 5 ns Input and output timing 1.5V reference levels Output load (including scope and jig) URL : www.hbe.co.kr Rev. 1.0 (June, 2002) +5V 1.9KΩ DOUT 1KΩ ( unless otherwise specified) Figure 1. Output Load A See Figures 1and 2 4 +5V 1.9KΩ DOUT 100㎊ 1KΩ 5㎊ Figure 2. Output Load B HANBit Electronics Co.,Ltd HANBit HMN1288D READ CYCLE (TA= TOPR, VCCmin £ VCC≤ VCCmax ) PARAMETER SYMBOL Read Cycle Time tRC CONDITIONS -70 -85 -120 -150 UNIT MIN MAX MIN MAX MIN MAX MIN MAX 70 - 85 - 120 - 150 - ns Address Access Time tACC Output load A - 70 - 85 - 120 - 150 ns Chip enable access time tACE Output load A - 70 - 85 - 120 - 150 ns Output enable to Output valid tOE Output load A - 35 - 45 - 60 - 70 ns Chip enable to output in low Z tCLZ Output load B 5 - 5 - 5 - 10 - ns Output enable to output in low Z tOLZ Output load B 5 - 0 - 0 - 5 - ns Chip disable to output in high Z tCHZ Output load B 0 25 0 35 0 45 0 60 ns Output disable to output high Z tOHZ Output load B 0 25 0 25 0 35 0 50 ns Output hold from address change tOH Output load A 10 - 10 - 10 - 10 - ns WRITE CYCLE (TA= TOPR, Vccmin £ Vcc ≤ Vccmax ) PARAMETER SYMBOL Write Cycle Time tWC Chip enable to end of write tCW Address setup time tAS Address valid to end of write CONDITIONS -70 -85 -120 -150 UNI MIN MAX MIN MAX MIN MAX Min Max T 70 - 85 - 120 - 150 - ns Note 1 65 - 75 - 100 - 100 - ns Note 2 0 - 0 - 0 - 0 - ns tAW Note 1 65 - 75 - 100 - 90 - ns Write pulse width tWP Note 1 55 - 65 - 85 - 90 - ns Write recovery time (write cycle 1) tWR1 Note 3 5 - 5 - 5 - 5 - ns Write recovery time (write cycle 2) tWR2 Note 3 15 - 15 - 15 - 15 - ns Data valid to end of write tDW 30 - 35 - 45 - 50 - ns Data hold time (write cycle 1) tDH1 Note 4 0 - 0 - 0 - 0 - ns Data hold time (write cycle 2) tDH2 Note 4 10 - 10 - 10 - 0 - ns Write enabled to output in high Z tWZ Note 5 0 25 0 30 0 40 0 50 ns Output active from end of write tOW Note 5 5 - 0 - 0 - 5 - ns NOTE: 1. A write ends at the earlier transition of /CE going high and /WE going high. 2. A write occurs during the overlap of allow /CE and a low /WE. A write begins at the later transition of /CE going low and /WE going low. 3. Either tWR1 or tWR2 must be met. 4. Either tDH1 or tDH2 must be met. 5. If /CE goes low simultaneously with /WE going low or after /WE going low, the outputs remain in highimpedance state. URL : www.hbe.co.kr Rev. 1.0 (June, 2002) 5 HANBit Electronics Co.,Ltd HANBit HMN1288D POWER-DOWN/POWER-UP CYCLE (TA= TOPR, VCC=5V) PARAMETER SYMBOL CONDITIONS MIN TYP. MAX UNIT VCC slew, 4.75 to 4.25V tPF 300 - - ㎲ VCC slew, 4.75 to VSO tFS 10 - - ㎲ VCC slew, VSO to VPFD (max) tPU 0 - - ㎲ 40 80 120 ms 10 - - years 40 100 150 ㎲ Time during which SRAM Chip enable recovery time tCER is write-protected after VCC passes VPFD on power-up. Data-retention time in Absence of VCC TA = 25℃ tDR Delay after VCC slew’s down Write-protect time tWPT past VPFD before SRAM is Write-protected. TIMING WAVEFORM - READ CYCLE NO.1 (Address Access)*1,2 tRC Address tACC tOH Previous Data Valid DOUT Data Valid - READ CYCLE NO.2 (/CE Access)*1,3,4 tRC CE tACE tCHZ tCLZ DOUT URL : www.hbe.co.kr Rev. 1.0 (June, 2002) High-Z High-Z 6 HANBit Electronics Co.,Ltd HANBit HMN1288D - READ CYCLE NO.3 (/OE Access)*1,5 tRC Address tACC /OE tOE DOUT NOTES: tOHZ tOLZ Data Valid High-Z High-Z 1. /WE is held high for a read cycle. 2. Device is continuously selected: /CE = /OE =VIL. 3. Address is valid prior to or coincident with /CE transition low. 4. /OE = VIL. 5. Device is continuously selected: /CE = VIL - WRITE CYCLE NO.1 (/WE-CONTROLLED)*1,2,3 tWC Address tAW tWR1 tCW /CE tAS tWP /WE tDW DIN Data-in Valid tWZ DOUT Rev. 1.0 (June, 2002) tOW High-Z Data Undefined (1) URL : www.hbe.co.kr tDH1 7 HANBit Electronics Co.,Ltd HANBit HMN1288D - WRITE CYCLE NO.2 (/CE-Controlled)*1,2,3,4,5 tWC Address tAW tAS tWR2 tCW /CE tWP /WE tDH2 tDW Data-in DIN tWZ DOUT Data NOTE: High-Z Undefined 1. /CE or /WE must be high during address transition. 2. Because I/O may be active (/OE low) during this period, data input signals of opposite polarity to the outputs must not be applied. 3. If /OE is high, the I/O pins remain in a state of high impedance. 4. Either tWR1 or tWR2 must be met. 5. Either tDH1 or tDH2 must be met. - POWER-DOWN/POWER-UP TIMING tPF VCC 4.75 VPFD VPFD 4.25 VSO VSO tFS tWPT tPU tCER tDR /CE URL : www.hbe.co.kr Rev. 1.0 (June, 2002) 8 HANBit Electronics Co.,Ltd HANBit HMN1288D PACKAGE DIMENSION Dimension Min Max A 1.680 1.680 B 0.720 0.740 C 0.365 0.375 D 0.015 0.025 E 0.008 0.013 F 0.590 0.630 G 0.015 0.021 H 0.090 0.110 I 0.080 0.110 J 0.120 0.160 J A I H G B C D E F All dimensions are in inches. ORDERING INFORMATION H M N 1288 D-70 I Operating Temp. : Blank = Commercial (0 to 70 °C ) I = Industrial (-40 to 85°C) Speed options : 70 = 70 ns 85 = 85 ns 120 = 120 ns 150 = 150 ns Dip type package Device : 128K x 8 bit Nonvolatile SRAM HANBit Memory Module URL : www.hbe.co.kr Rev. 1.0 (June, 2002) 9 HANBit Electronics Co.,Ltd