Murata LQH31HNR75J03 Chip inductor (chip coil) for high frequency vertical wire wound ferrite type Datasheet

Inductors (Coils) > Chip Inductor (Chip Coil) > for High Frequency Vertical Wire Wound Ferrite Type
Data Sheet
1
Chip Inductor (Chip Coil) for High Frequency Vertical Wire Wound Ferrite Type
LQH31H Series (1206 Size)
■ Dimensions
■ Packaging
2.3±0.2
1.8±0.2
1.6±0.2
Code
Packaging
Minimum Quantity
L
180mm Embossed Tape
2000
K
330mm Embossed Tape
7500
1.6±0.2
3.2±0.3
(in mm)
0.7 min. 0.7 min. 0.7 min.
■ Rated Value (p: packaging code)
Part Number
Inductance
Test Frequency
Rated Current
DC Resistance Q (min.) Test Frequency
Self Resonance Frequency (min.)
LQH31HN54NK03p
54nH±10%
1MHz
920mA
0.035ohm±30%
50
100MHz
800MHz
LQH31HN95NK03p
95nH±10%
1MHz
790mA
0.047ohm±30%
60
100MHz
650MHz
LQH31HNR14J03p
145nH±5%
1MHz
700mA
0.061ohm±30%
60
100MHz
500MHz
LQH31HNR14K03p
145nH±10%
1MHz
700mA
0.061ohm±30%
60
100MHz
500MHz
LQH31HNR21J03p
215nH±5%
1MHz
520mA
0.11ohm±30%
60
100MHz
430MHz
LQH31HNR21K03p
215nH±10%
1MHz
520mA
0.11ohm±30%
60
100MHz
430MHz
LQH31HNR29J03p
290nH±5%
1MHz
420mA
0.17ohm±30%
60
100MHz
360MHz
LQH31HNR29K03p
290nH±10%
1MHz
420mA
0.17ohm±30%
60
100MHz
360MHz
LQH31HNR39J03p
390nH±5%
1MHz
330mA
0.26ohm±30%
60
100MHz
300MHz
LQH31HNR39K03p
390nH±10%
1MHz
330mA
0.26ohm±30%
60
100MHz
300MHz
LQH31HNR50J03p
500nH±5%
1MHz
260mA
0.44ohm±30%
60
100MHz
270MHz
LQH31HNR50K03p
500nH±10%
1MHz
260mA
0.44ohm±30%
60
100MHz
270MHz
LQH31HNR61J03p
610nH±5%
1MHz
250mA
0.48ohm±30%
60
100MHz
240MHz
LQH31HNR61K03p
610nH±10%
1MHz
250mA
0.48ohm±30%
60
100MHz
240MHz
LQH31HNR75J03p
750nH±5%
1MHz
190mA
0.79ohm±30%
60
100MHz
220MHz
LQH31HNR75K03p
750nH±10%
1MHz
190mA
0.79ohm±30%
60
100MHz
220MHz
LQH31HNR88J03p
880nH±5%
1MHz
180mA
0.86ohm±30%
60
100MHz
200MHz
LQH31HNR88K03p
880nH±10%
1MHz
180mA
0.86ohm±30%
60
100MHz
200MHz
Operating Temperature Range: -40°C to +85°C
Continued on the following page.
o This data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design.
! Note:
1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our
products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product
specifications or transact the approval sheet for product specifications before ordering.
2010.9.9
http://www.murata.com/
Inductors (Coils) > Chip Inductor (Chip Coil) > for High Frequency Vertical Wire Wound Ferrite Type
Data Sheet
2
Continued from the preceding page.
■ Q-Frequency Characteristics (Typ.)
100
215nH
880nH
80
54nH
Q
60
40
20
0
1
10
100
1000
Frequency (MHz)
■ !Caution/Notice
!Caution (Rating)
Do not use products beyond the rated current as
this may create excessive heat.
Notice
Solderability of Tin plating termination chip might be
deteriorated when low temperature soldering profile
where peak solder temperature is below the Tin melting
point is used. Please confirm the solderability of Tin
plating termination chip before use.
o This data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design.
! Note:
1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our
products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product
specifications or transact the approval sheet for product specifications before ordering.
2010.9.9
http://www.murata.com/
Similar pages