Document 1092 Flyback Transformer For Linear Technology LT8584 • Developed for Linear Technology LT8584 Isolated Monolithic Active Cell Balancer • Designed to operate at 140 kHz • Rated for 7 – 12 Watts • 1500 Vrms, one minute isolation between primary and secondary Core material Ferrite Terminations RoHS tin-silver-copper over tin over nickel over phos bronze. Other terminations available at additional cost. Weight 3.9 – 4.2 g Ambient temperature –40°C to +85°C Maximum part temperature +85°C (ambient + temp rise) Storage temperature Component: –40°C to +85°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 200 per 13″ reel Plastic tape: 32 mm wide, 0.5 mm thick, 24 mm pocket spacing, 11.2 mm pocket depth PCB washing Tested to MIL-STD-202 Method 215 plus an additional aqueous wash. See Doc787_PCB_Washing.pdf. Part number1 NA6252-AL_ NA5920-AL_ Input Inductance voltage at 0 A2 (V) ±10% (µH) 2–8 2–8 Inductance at Ipk3 min (µH) 4.0 4.0 3.6 3.2 LeakageOutput DCR max (Ohms)4 inductance Turns ratio6 Ipk3 voltage pri sec max (µH)5 pri : sec (A) (V) 0.010 0.013 0.053 5.15 0.075 0.050 1 : 1.33 1 : 24 7.0 9 – 36 7.0 100 – 400 1. When ordering, please specify packaging code: Dot above pin1 0.004 /0,10 0.041 1,05 8 Pri Sec 4 3 5 Part number Internal code 0.600 max 15,24 0.413 10,50 5 4 0.024 0,60 0.080 2,03 0.460 11,68 1 0.050 1,27 0.50 max 12,7 1 1 2 NAXXXX-AL 0.450 max 11,43 XXXX Y NA6252-ALD Packaging: D = 13″ machine-ready reel. EIA-481 embossed plastic tape (200 parts per full reel). B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter D instead. 2. Inductance is for the primary, measured at 150 kHz, 0.1 Vrms, 0 Adc. 3. Ipk is peak primary current drawn at minimum input voltage. 4. DCR for the primary is measured with windings connected in parallel. 5. Leakage inductance is for the primary, measured with secondary pins shorted. 6. Turns ratio is with the primary windings connected in parallel. 7. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Dimensions are in 8 0.098 2,50 Recommended 0.098 2,50 Land Pattern inches mm Primary windings to be connected in parallel on PC board US +1-847-639-6400 [email protected] UK +44-1236-730595 [email protected] Taiwan +886-2-2264 3646 [email protected] China +86-21-6218 8074 [email protected] Singapore + 65-6484 8412 [email protected] Document 1092 Revised 06/10/16 © Coilcraft Inc. 2016 This product may not be used in medical or high risk applications without prior Coilcraft approval. Specification subject to change without notice. Please check web site for latest information.