ATMEL ATF1502ASL-25AU44 Highperformance eeprom cpld Datasheet

Features
• High-density, High-performance, Electrically-erasable Complex Programmable
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Logic Device
– 32 Macrocells
– 5 Product Terms per Macrocell, Expandable up to 40 per Macrocell
– 44 Pins
– 7.5 ns Maximum Pin-to-pin Delay
– Registered Operation up to 125 MHz
– Enhanced Routing Resources
In-System Programmability (ISP) via JTAG
Flexible Logic Macrocell
– D/T Latch Configurable Flip-flops
– Global and Individual Register Control Signals
– Global and Individual Output Enable
– Programmable Output Slew Rate
– Programmable Output Open Collector Option
– Maximum Logic Utilization by Burying a Register with a COM Output
Advanced Power Management Features
Automatic 10 µA Standby for “L” Version
Pin-controlled 1 mA Standby Mode
Programmable Pin-keeper Inputs and I/Os
Reduced-power Feature per Macrocell
Available in Commercial and Industrial Temperature Ranges
Available in 44-lead PLCC and TQFP
Advanced EEPROM Technology
– 100% Tested
– Completely Reprogrammable
– 10,000 Program/Erase Cycles
– 20-year Data Retention
– 2000V ESD Protection
– 200 mA Latch-up Immunity
JTAG Boundary-scan Testing to IEEE Std. 1149.1-1990 and 1149.1a-1993 Supported
PCI-compliant
Security Fuse Feature
Green (Pb/Halide-fee/RoHS Compliant) Package Options
Highperformance
EEPROM CPLD
ATF1502AS
ATF1502ASL
Enhanced Features
•
•
•
•
•
•
•
•
•
•
•
Improved Connectivity (Additional Feedback Routing, Alternate Input Routing)
Output Enable Product Terms
D Latch Mode
Combinatorial Output with Registered Feedback within Any Macrocell
Three Global Clock Pins
ITD (Input Transition Detection) Circuits on Global Clocks, Inputs and I/O
(“L” Versions)
Fast Registered Input from Product Term
Programmable “Pin-keeper” Option
VCC Power-up Reset Option
Pull-up Option on JTAG Pins TMS and TDI
Advanced Power Management Features
– Input Transition Detection
– Power-down (“L” Versions)
– Individual Macrocell Power Option
– Disable ITD on Global Clocks, Inputs and I/O
Rev. 0995K–PLD–6/05
1
44
43
42
41
40
39
38
37
36
35
34
I/O
I/O
I/O
VCC
GCLK2/OE2/I
GCLR/I
I/OE1
GCLK1/I
GND
GCLK3/I/O
I/O
44-lead TQFP
Top View
33
32
31
30
29
28
27
26
25
24
23
1
2
3
4
5
6
7
8
9
10
11
I/O
I/O/TDO
I/O
I/O
VCC
I/O
I/O
I/O/TCK
I/O
GND
I/O
I/O
I/O
I/O
I/O
GND
VCC
I/O
PD2/I/O
I/O
I/O
I/O
12
13
14
15
16
17
18
19
20
21
22
I/O/TDI
I/O
I/O
GND
PD1/I/O
I/O
TMS/I/O
I/O
VCC
I/O
I/O
39
38
37
36
35
34
33
32
31
30
29
18
19
20
21
22
23
24
25
26
27
28
7
8
9
10
11
12
13
14
15
16
17
I/O
I/O/TDO
I/O
I/O
VCC
I/O
I/O
I/O/TCK
I/O
GND
I/O
I/O
I/O
I/O
I/O
GND
VCC
I/O
PD2/I/O
I/O
I/O
I/O
TDI/I/O
I/O
I/O
GND
PD1/I/O
I/O
I/O/TMS
I/O
VCC
I/O
I/O
6
5
4
3
2
1
44
43
42
41
40
I/O
I/O
I/O
VCC
GCLK2/OE2/I
GCLR/I
OE1/I
GCLK1/I
GND
GCLK3/I/O
I/O
44-lead PLCC
Top View
Description
The ATF1502AS is a high-performance, high-density complex programmable logic device
(CPLD) that utilizes Atmel’s proven electrically-erasable technology. With 32 logic macrocells
and up to 36 inputs, it easily integrates logic from several TTL, SSI, MSI, LSI and classic
PLDs. The ATF1502AS’s enhanced routing switch matrices increase usable gate count and
the odds of successful pin-locked design modifications.
The ATF1502AS has up to 32 bi-directional I/O pins and four dedicated input pins, depending
on the type of device package selected. Each dedicated pin can also serve as a global control
signal, register clock, register reset or output enable. Each of these control signals can be
selected for use individually within each macrocell.
2
ATF1502AS(L)
0995K–PLD–6/05
ATF1502AS(L)
Block Diagram
B
32
Each of the 32 macrocells generates a buried feedback that goes to the global bus. Each input
and I/O pin also feeds into the global bus. The switch matrix in each logic block then selects 40
individual signals from the global bus. Each macrocell also generates a foldback logic term
that goes to a regional bus. Cascade logic between macrocells in the ATF1502AS allows fast,
efficient generation of complex logic functions. The ATF1502AS contains four such logic
chains, each capable of creating sum term logic with a fan-in of up to 40 product terms.
The ATF1502AS macrocell, shown in Figure 1, is flexible enough to support highly complex
logic functions operating at high speed. The macrocell consists of five sections: product terms
and product term select multiplexer, OR/XOR/CASCADE logic, a flip-flop, output select and
enable, and logic array inputs.
Unused product terms are automatically disabled by the compiler to decrease power consumption. A security fuse, when programmed, protects the contents of the ATF1502AS. Two
bytes (16 bits) of User Signature are accessible to the user for purposes such as storing
project name, part number, revision or date. The User Signature is accessible regardless of
the state of the security fuse.
The ATF1502AS device is an in-system programmable (ISP) device. It uses the industry standard 4-pin JTAG interface (IEEE Std. 1149.1), and is fully compliant with JTAG’s Boundaryscan Description Language (BSDL). ISP allows the device to be programmed without removing it from the printed circuit board. In addition to simplifying the manufacturing flow, ISP also
allows design modifications to be made in the field via software.
3
0995K–PLD–6/05
Figure 1. ATF1502AS Macrocell
Product Terms and
Select Mux
Each ATF1502AS macrocell has five product terms. Each product term receives as its inputs
all signals from both the global bus and regional bus.
The product term select multiplexer (PTMUX) allocates the five product terms as needed to
the macrocell logic gates and control signals. The PTMUX programming is determined by the
design compiler, which selects the optimum macrocell configuration.
OR/XOR/
CASCADE Logic
The ATF1502AS’s logic structure is designed to efficiently support all types of logic. Within a
single macrocell, all the product terms can be routed to the OR gate, creating a 5-input
AND/OR sum term. With the addition of the CASIN from neighboring macrocells, this can be
expanded to as many as 40 product terms with little additional delay.
The macrocell’s XOR gate allows efficient implementation of compare and arithmetic functions. One input to the XOR comes from the OR sum term. The other XOR input can be a
product term or a fixed high or low level. For combinatorial outputs, the fixed level input allows
polarity selection. For registered functions, the fixed levels allow DeMorgan minimization of
product terms. The XOR gate is also used to emulate T- and JK-type flip-flops.
Flip-flop
4
The ATF1502AS’s flip-flop has very flexible data and control functions. The data input can
come from either the XOR gate, from a separate product term or directly from the I/O pin.
Selecting the separate product term allows creation of a buried registered feedback within a
combinatorial output macrocell. (This feature is automatically implemented by the fitter software). In addition to D, T, JK and SR operation, the flip-flop can also be configured as a flowthrough latch. In this mode, data passes through when the clock is high and is latched when
the clock is low.
ATF1502AS(L)
0995K–PLD–6/05
ATF1502AS(L)
The clock itself can be either one of the Global CLK signals (GCK[0 : 2]) or an individual product term. The flip-flop changes state on the clock’s rising edge. When the GCK signal is used
as the clock, one of the macrocell product terms can be selected as a clock enable. When the
clock enable function is active and the enable signal (product term) is low, all clock edges are
ignored. The flip-flop’s asynchronous reset signal (AR) can be either the Global Clear
(GCLEAR), a product term, or always off. AR can also be a logic OR of GCLEAR with a product term. The asynchronous preset (AP) can be a product term or always off.
Extra Feedback
The ATF1502AS(L) macrocell output can be selected as registered or combinatorial. The
extra buried feedback signal can be either combinatorial or a registered signal regardless of
whether the output is combinatorial or registered. (This enhancement function is automatically
implemented by the fitter software.) Feedback of a buried combinatorial output allows the creation of a second latch within a macrocell.
I/O Control
The output enable multiplexer (MOE) controls the output enable signal. Each I/O can be individually configured as an input, output or for bi-directional operation. The output enable for
each macrocell can be selected from the true or compliment of the two output enable pins, a
subset of the I/O pins, or a subset of the I/O macrocells. This selection is automatically done
by the fitter software when the I/O is configured as an input, all macrocell resources are still
available, including the buried feedback, expander and cascade logic.
Global Bus/Switch
Matrix
The global bus contains all input and I/O pin signals as well as the buried feedback signal from
all 32 macrocells. The switch matrix in each logic block receives as its inputs all signals from
the global bus. Under software control, up to 40 of these signals can be selected as inputs to
the logic block.
Foldback Bus
Each macrocell also generates a foldback product term. This signal goes to the regional bus
and is available to four macrocells. The foldback is an inverse polarity of one of the macrocell’s
product terms. The four foldback terms in each region allow generation of high fan-in sum
terms (up to nine product terms) with little additional delay.
Programmable
Pin-keeper
Option for
Inputs and I/Os
The ATF1502AS offers the option of programming all input and I/O pins so that pin-keeper circuits can be utilized. When any pin is driven high or low and then subsequently left floating, it
will stay at that previous high or low level. This circuitry prevents unused input and I/O lines
from floating to intermediate voltage levels, which causes unnecessary power consumption
and system noise. The keeper circuits eliminate the need for external pull-up resistors and
eliminate their DC power consumption.
5
0995K–PLD–6/05
Input Diagram
I/O Diagram
Speed/Power
Management
The ATF1502AS has several built-in speed and power management features. The
ATF1502AS contains circuitry that automatically puts the device into a low-power standby
mode when no logic transitions are occurring. This not only reduces power consumption during inactive periods, but also provides proportional power savings for most applications
running at system speeds below 50 MHz. This feature may be selected as a design option.
To further reduce power, each ATF1502AS macrocell has a reduced-power bit feature. This
feature allows individual macrocells to be configured for maximum power savings. This feature
may be selected as a design option.
The ATF1502AS also has an optional power-down mode. In this mode, current drops to below
10 mA. When the power-down option is selected, either PD1 or PD2 pins (or both) can be
used to power down the part. The power-down option is selected in the design source file.
When enabled, the device goes into power-down when either PD1 or PD2 is high. In the
power-down mode, all internal logic signals are latched and held, as are any enabled outputs.
6
ATF1502AS(L)
0995K–PLD–6/05
ATF1502AS(L)
All pin transitions are ignored until the PD pin is brought low. When the power-down feature is
enabled, the PD1 or PD2 pin cannot be used as a logic input or output. However, the pin’s
macrocell may still be used to generate buried foldback and cascade logic signals.
All power-down AC characteristic parameters are computed from external input or I/O pins,
with reduced-power bit turned on. For macrocells in reduced-power mode (reduced-power bit
turned on), the reduced-power adder, tRPA , must be added to the AC parameters, which
include the data paths tLAD, tLAC, tIC, tACL, tACH and tSEXP.
The ATF1502AS macrocell also has an option whereby the power can be reduced on a permacrocell basis. By enabling this power-down option, macrocells that are not used in an application can be turned down, thereby reducing the overall power consumption of the device.
Each output also has individual slew rate control. This may be used to reduce system noise by
slowing down outputs that do not need to operate at maximum speed. Outputs default to slow
switching, and may be specified as fast switching in the design file.
Design
Software
Support
ATF1502AS designs are supported by several third-party tools. Automated fitters allow logic
synthesis using a variety of high-level description languages and formats.
Power-up Reset
The ATF1502AS is designed with a power-up reset, a feature critical for state machine initialization. At a point delayed slightly from VCC crossing VRST, all registers will be initialized, and
the state of each output will depend on the polarity of its buffer. However, due to the asynchronous nature of reset and uncertainty of how VCC actually rises in the system, the following
conditions are required:
1. The VCC rise must be monotonic,
2. After reset occurs, all input and feedback setup times must be met before driving the
clock pin high, and,
3. The clock must remain stable during TD.
The ATF1502AS has two options for the hysteresis about the reset level, VRST, Small and
Large. During the fitting process users may configure the device with the Power-up Reset hysteresis set to Large or Small. Atmel POF2JED users may select the Large option by including
the flag “-power_reset” on the command line after “filename.POF”. To allow the registers to be
properly reinitialized with the Large hysteresis option selected, the following condition is
added:
4. If VCC falls below 2.0V, it must shut off completely before the device is turned on again.
When the Large hysteresis option is active, ICC is reduced by several hundred microamps as
well.
Security Fuse
Usage
A single fuse is provided to prevent unauthorized copying of the ATF1502AS fuse patterns.
Once programmed, fuse verify is inhibited. However, the 16-bit User Signature remains
accessible.
Programming
ATF1502AS devices are in-system programmable (ISP) devices utilizing the 4-pin JTAG protocol. This capability eliminates package handling normally required for programming and
facilitates rapid design iterations and field changes.
7
0995K–PLD–6/05
Atmel provides ISP hardware and software to allow programming of the ATF1502AS via the
PC. ISP is performed by using either a download cable, a comparable board tester or a simple
microprocessor interface.
When using the ISP hardware or software to program the ATF1502AS devices, four I/O pins
must be reserved for the JTAG interface. However, the logic features that the macrocells have
associated with these I/O pins are still available to the design for burned logic functions.
To facilitate ISP programming by the Automated Test Equipment (ATE) vendors, Serial Vector
Format (SVF) files can be created by Atmel-provided software utilities.
ATF1502AS devices can also be programmed using standard third-party programmers. With a
third-party programmer, the JTAG ISP port can be disabled, thereby allowing four additional
I/O pins to be used for logic.
Contact your local Atmel representatives or Atmel PLD applications for details.
ISP
Programming
Protection
The ATF1502AS has a special feature that locks the device and prevents the inputs and I/O
from driving if the programming process is interrupted for any reason. The inputs and I/O
default to high-Z state during such a condition. In addition, the pin-keeper option preserves the
previous state of the input and I/O PMS during programming.
All ATF1502AS devices are initially shipped in the erased state, thereby making them ready to
use for ISP.
Note:
JTAG-BST/ISP
Overview
For more information refer to the “Designing for In-System Programmability with Atmel CPLDs”
application note.
The JTAG boundary-scan testing is controlled by the Test Access Port (TAP) controller in the
ATF1502AS. The boundary-scan technique involves the inclusion of a shift-register stage
(contained in a boundary-scan cell) adjacent to each component so that signals at component
boundaries can be controlled and observed using scan testing methods. Each input pin and
I/O pin has its own boundary-scan cell (BSC) to support boundary-scan testing. The
ATF1502AS does not include a Test Reset (TRST) input pin because the TAP controller is
automatically reset at power-up. The five JTAG modes supported include:
SAMPLE/PRELOAD, EXTEST, BYPASS, IDCODE and HIGHZ. The ATF1502AS’s ISP can
be fully described using JTAG’s BSDL as described in IEEE Standard 1149.1b. This allows
ATF1502AS programming to be described and implemented using any one of the third-party
development tools supporting this standard.
The ATF1502AS has the option of using four JTAG-standard I/O pins for boundary-scan testing (BST) and in-system programming (ISP) purposes. The ATF1502AS is programmable
through the four JTAG pins using the IEEE standard JTAG programming protocol established
by IEEE Standard 1149.1 using 5V TTL-level programming signals from the ISP interface for
in-system programming. The JTAG feature is a programmable option. If JTAG (BST or ISP) is
not needed, then the four JTAG control pins are available as I/O pins.
8
ATF1502AS(L)
0995K–PLD–6/05
ATF1502AS(L)
JTAG
Boundary-scan
Cell (BSC)
Testing
The ATF1502AS contains up to 32 I/O pins and four input pins, depending on the device type
and package type selected. Each input pin and I/O pin has its own boundary-scan cell (BSC)
in order to support boundary-scan testing as described in detail by IEEE Standard 1149.1. A
typical BSC consists of three capture registers or scan registers and up to two update registers. There are two types of BSCs, one for input or I/O pin, and one for the macrocells. The
BSCs in the device are chained together through the capture registers. Input to the capture
register chain is fed in from the TDI pin while the output is directed to the TDO pin. Capture
registers are used to capture active device data signals, to shift data in and out of the device
and to load data into the update registers. Control signals are generated internally by the
JTAG TAP controller. The BSC configuration for the input and I/O pins and macrocells is
shown below.
BSC
Configuration
for Input and I/O
Pins (Except
JTAG TAP Pins)
Note:
BSC
Configuration
for Macrocell
1. The ATF1502AS has a pull-up option on TMS and TDI pins. This feature is selected as a
design option.
TDO
0
Q D
1
TDI
CLOCK
TDO
OEJ
0
0
1
D Q
D Q
1
OUTJ
0
0
Pin
1
D Q
D Q
Capture
DR
Update
DR
1
Mode
TDI
Shift
Clock
BSC for I/O Pins and Macrocells
9
0995K–PLD–6/05
The ATF1502AS also supports the growing need in the industry to support the new Peripheral
Component Interconnect (PCI) interface standard in PCI-based designs and specifications.
The PCI interface calls for high current drivers, which are much larger than the traditional TTL
drivers. In general, PLDs and FPGAs parallel outputs to support the high current load required
by the PCI interface. The ATF1502AS allows this without contributing to system noise while
delivering low output to output skew. Having a programmable high drive option is also possible
without increasing output delay or pin capacitance. The PCI electrical characteristics appear
on the next page.
PCI Voltage-tocurrent Curves
for +5V
Signaling in
Pull-up Mode
Pull Up
VCC
Test Point
Voltage
PCI Compliance
2.4
DC
drive point
1.4
AC drive
point
-44 Current (mA) -178
-2
Pull Down
VCC
AC drive
point
Voltage
PCI Voltage-tocurrent Curves
for +5V
Signaling in
Pull-down Mode
2.2
DC
drive point
0.55
Test Point
3,6
10
95 Current (mA) 380
ATF1502AS(L)
0995K–PLD–6/05
ATF1502AS(L)
PCI DC Characteristics (Preliminary)
Symbol
Parameter
VCC
Conditions
Min
Max
Units
Supply Voltage
4.75
5.25
V
VIH
Input High Voltage
2.0
VCC + 0.5
V
VIL
Input Low Voltage
-0.5
0.8
V
IIH
Input High Leakage Current(1)
VIN = 2.7V
70
µA
VIN = 0.5V
-70
µA
(1)
IIL
Input Low Leakage Current
VOH
Output High Voltage
IOUT = -2 mA
VOL
Output Low Voltage
IOUT = 3 mA, 6 mA
CIN
2.4
V
0.55
V
Input Pin Capacitance
10
pF
CCLK
CLK Pin Capacitance
12
pF
CIDSEL
IDSEL Pin Capacitance
8
pF
20
nH
LPIN
Note:
Pin Inductance
1. Leakage current is with pin-keeper off.
PCI AC Characteristics (Preliminary)
Symbol
Parameter
Conditions
Min
IOH(AC)
Switching
Current High
(Test High)
0 < VOUT ≤ 1.4
-44
mA
-44 + (VOUT - 1.4)
/0.024
mA
1.4 < VOUT < 2.4
3.1 < VOUT < VCC
VOUT = 3.1V
IOL(AC)
Switching
Current Low
(Test Point)
VOUT > 2.2V
2.2 > VOUT > 0
-5 < VIN ≤ -1
SLEWR
Output Rise Slew Rate
0.4V to 2.4V load
Equation A
mA
-142
µA
mA
VOUT/0.023
mA
VOUT = 0.71
Low Clamp Current
Units
95
0.1 > VOUT > 0
ICL
Max
Equation B
mA
206
mA
-25 + (VIN + 1)
/0.015
1
SLEWF
Output Fall Slew Rate
2.4V to 0.4V load
1
Notes: 1. Equation A: IOH = 11.9 (VOUT - 5.25) * (VOUT + 2.45) for VCC > VOUT > 3.1V.
2. Equation B: IOL = 78.5 * VOUT * (4.4 - VOUT) for 0V < VOUT < 0.71V.
mA
5
V/ns
5
V/ns
11
0995K–PLD–6/05
Power-down
Mode
The ATF1502AS includes an optional pin-controlled power-down feature. When this mode is
enabled, the PD pin acts as the power-down pin. When the PD pin is high, the device supply
current is reduced to less than 5 mA. During power-down, all output data and internal logic
states are latched and held. Therefore, all registered and combinatorial output data remain
valid. Any outputs that were in a high-Z state at the onset will remain at high-Z. During
power-down, all input signals except the power-down pin are blocked. Input and I/O hold
latches remain active to ensure that pins do not float to indeterminate levels, further reducing
system power. The power-down pin feature is enabled in the logic design file. Designs using
the power-down pin may not use the PD pin logic array input. However, all other PD pin macrocell resources may still be used, including the buried feedback and foldback product term
array inputs.
Power-down AC Characteristics(1)(2)
-7
Max
Max
Min
-25
Parameter
tIVDH
Valid I, I/O before PD High
7
10
15
25
ns
tGVDH
Valid OE(2) before PD High
7
10
15
25
ns
tCVDH
Valid Clock(2) before PD High
7
10
15
25
ns
tDHIX
I, I/O Don’t Care after PD High
Max
Min
Max
Units
12
15
25
35
ns
12
15
25
35
ns
tDHGX
OE
tDHCX
Clock(2) Don’t Care after PD High
12
15
25
35
ns
tDLIV
PD Low to Valid I, I/O
1
1
1
1
µs
tDLGV
PD Low to Valid OE (Pin or Term)
1
1
1
1
µs
tDLCV
PD Low to Valid Clock (Pin or Term)
1
1
1
1
µs
1
1
1
1
µs
tDLOV
Notes:
Don’t Care after PD High
Min
-15
Symbol
(2)
Min
-10
PD Low to Valid Output
1. For slow slew outputs, add tSSO.
2. Pin or product term.
Absolute Maximum Ratings*
Temperature Under Bias.................................. -40°C to +85°C
*NOTICE:
Storage Temperature ..................................... -65°C to +150°C
Voltage on Any Pin with
Respect to Ground .........................................-2.0V to +7.0V(1)
Voltage on Input Pins
with Respect to Ground
During Programming.....................................-2.0V to +14.0V(1)
Programming Voltage with
Respect to Ground .......................................-2.0V to +14.0V(1)
12
Note:
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect device
reliability.
1. Minimum voltage is -0.6V DC, which may undershoot to -2.0V for pulses of less than 20 ns.
Maximum output pin voltage is VCC + 0.75V DC,
which may overshoot to 7.0V for pulses of less
than 20 ns.
ATF1502AS(L)
0995K–PLD–6/05
ATF1502AS(L)
DC and AC Operating Conditions
Operating Temperature (Ambient)
Commercial
Industrial
0°C - 70°C
-40°C - 85°C
5V ± 5%
5V ± 10%
VCC (5V) Power Supply
DC Characteristics
Symbol
Parameter
Condition
Min
IIL
Input or I/O Low
Leakage Current
VIN = VCC
IIH
Input or I/O High
Leakage Current
IOZ
Tri-state Output
Off-state Current
VO = VCC or GND
ICC1
Power Supply Current, Standby
VCC = Max
VIN = 0, VCC
Std Mode
“L” Mode
ICC2
Power Supply Current,
Power-down Mode
VCC = Max
VIN = 0, VCC
“PD” Mode
ICC3(2)
Reduced-power Mode
Supply Current, Standby
VCC = Max
VIN = 0, VCC
Std Mode
Typ
Max
Units
-2
-10
µA
2
10
-40
40
µA
Com.
60
mA
Ind.
75
mA
Com.
10
µA
Ind.
10
µA
1
5
mA
Com.
35
mA
Ind.
40
mA
VIL
Input Low Voltage
-0.3
0.8
V
VIH
Input High Voltage
2.0
VCCIO + 0.3
V
VOL
Output Low Voltage (TTL)
3.0
0.45
V
Output Low Voltage (CMOS)
VOH
Notes:
Output High Voltage (TTL)
VIN = VIH or VIL
VCC = MIN, IOL = 12 mA
Com.
Ind.
0.45
VIN = VIH or VIL
VCC = MIN, IOL = 0.1 mA
Com.
0.2
V
Ind.
0.2
V
VIN = VIH or VIL
VCC = MIN, IOH = -4.0 mA
2.4
V
1. Not more than one output at a time should be shorted. Duration of short circuit test should not exceed 30 sec.
2. ICC3 refers to the current in the reduced-power mode when macrocell reduced-power is turned on.
13
0995K–PLD–6/05
Pin Capacitance(1)
Typ
Max
Units
Conditions
CIN
8
10
pF
VIN = 0V; f = 1.0 MHz
CI/O
8
10
pF
VOUT = 0V; f = 1.0 MHz
Note:
1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested.
The OGI pin (high-voltage pin during programming) has a maximum capacitance of 12 pF.
Timing Model
Input Test Waveforms and Measurement Levels
tR, tF = 1.5 ns typical
Output AC Test Loads
14
ATF1502AS(L)
0995K–PLD–6/05
ATF1502AS(L)
AC Characteristics (1)
-7
Min
-10
Max
Min
-15
-25
Symbol
Parameter
Max
Min
Max
7.5
10
3
7
9
3
tPD1
Input or Feedback to Non-registered Output
tPD2
I/O Input or Feedback to Non-registered
Feedback
tSU
Global Clock Setup Time
6
7
11
20
ns
tH
Global Clock Hold Time
0
0
0
0
ns
tFSU
Global Clock Setup Time of Fast Input
3
3
3
5
ns
tFH
Global Clock Hold Time of Fast Input
0.5
0.5
1
2
MHz
tCOP
Global Clock to Output Delay
tCH
Global Clock High Time
3
4
5
7
ns
tCL
Global Clock Low Time
3
4
5
7
ns
tASU
Array Clock Setup Time
3
3
4
5
ns
tAH
Array Clock Hold Time
2
3
4
6
ns
tACOP
Array Clock Output Delay
tACH
Array Clock High Time
3
4
6
10
ns
tACL
Array Clock Low Time
3
4
6
10
ns
tCNT
Minimum Clock Global Period
fCNT
Maximum Internal Global Clock Frequency
tACNT
Minimum Array Clock Period
fACNT
Maximum Internal Array Clock Frequency
fMAX
Maximum Clock Frequency
tIN
Input Pad and Buffer Delay
0.5
0.5
2
2
ns
tIO
I/O Input Pad and Buffer Delay
0.5
0.5
2
2
ns
tFIN
Fast Input Delay
1
1
2
2
ns
tSEXP
Foldback Term Delay
4
5
8
12
ns
tPEXP
Cascade Logic Delay
0.8
0.8
1
2
ns
tLAD
Logic Array Delay
3
5
6
8
ns
tLAC
Logic Control Delay
3
5
6
8
ns
tIOE
Internal Output Enable Delay
2
2
3
4
ns
tOD1
Output Buffer and Pad Delay
(Slow slew rate = OFF;
VCC = 5V; CL = 35 pF)
2
1.5
4
6
ns
tZX1
Output Buffer Enable Delay
(Slow slew rate = OFF;
VCCIO = 5.0V; CL = 35 pF)
4.0
5.0
7
10
ns
tZX2
Output Buffer Enable Delay
(Slow slew rate = OFF;
VCCIO = 3.3V; CL = 35 pF)
4.5
5.5
7
10
ns
4.5
5
7.5
125
8
Units
15
25
ns
12
25
ns
13
15
10
100
Max
8
10
8
Min
25
13
76.9
10
22
50
13
ns
ns
ns
MHz
22
ns
125
100
76.9
50
MHz
166.7
125
100
60
MHz
15
0995K–PLD–6/05
AC Characteristics (Continued)(1)
-7
Min
Max
Min
-25
Parameter
tZX3
Output Buffer Enable Delay
(Slow slew rate = ON;
VCCIO = 5.0V/3.3V; CL = 35 pF)
9
9
tXZ
Output Buffer Disable Delay (CL = 5 pF)
4
5
tSU
Register Setup Time
3
3
4
6
ns
tH
Register Hold Time
2
3
4
6
ns
tFSU
Register Setup Time of Fast Input
3
3
2
3
ns
tFH
Register Hold Time of Fast Input
0.5
0.5
2
5
ns
tRD
Register Delay
1
2
1
2
ns
tCOMB
Combinatorial Delay
1
2
1
2
ns
tIC
Array Clock Delay
3
5
6
8
ns
tEN
Register Enable Time
3
5
6
8
ns
tGLOB
Global Control Delay
1
1
1
1
ns
tPRE
Register Preset Time
2
3
4
6
ns
tCLR
Register Clear Time
2
3
4
6
ns
tUIM
Switch Matrix Delay
1
1
2
2
ns
16
Max
-15
Symbol
tRPA
Notes:
Min
-10
Max
Min
Max
Units
10
12
ns
6
8
ns
(2)
Reduced-power Adder
10
11
13
15
ns
1. See ordering information for valid part numbers.
2. The tRPA parameter must be added to the tLAD, tLAC,tTIC, tACL, and tSEXP parameters for macrocells running in the reducedpower mode.
ATF1502AS(L)
0995K–PLD–6/05
ATF1502AS(L)
SUPPLY CURRENT VS. SUPPLY VOLTAGE
(T = 25°C, NON-TURBO, BIT6 = 0, BIT 30 = 0)
SUPPLY CURRENT VS. SUPPLY VOLTAGE
AS VERSION (TA = 25°C, F = 0)
120.0
70
100.0
60
80.0
ICC (µA)
ICC (mA)
50
STANDARD POWER
40
60.0
40.0
30
20
20.0
REDUCED POWER
10
0.0
4.00
4.50
4.75
5.00
0
5.25
5.50
6.00
VCC (V)
4.5
4.75
5
5.25
5.5
VCC (V)
SUPPLY CURRENT VS. SUPPLY VOLTAGE
PIN-CONTROLLED POWER-DOWN MODE (TA = 25°C, F = 0)
14
12
ICC (mA)
10
8
TBD
6
4
2
0
4.5
4.75
5
5.25
SUPPLY CURRENT VS. FREQUENCY
ASL (LOW-POWER) VERSION (TA = 25°C)
5.5
VCC (V)
60.0
50.0
SUPPLY CURRENT VS. FREQUENCY
AS VERSION (TA = 25°C)
40.0
ICC (mA)
60.0
STANDARD POWER
30.0
50.0
STANDARD POWER
20.0
ICC (mA)
40.0
REDUCED POWER
10.0
30.0
0.0
20.0
0.00
REDUCED POWER
10.00
20.00
30.00
40.00
50.00
FREQUENCY (MHz)
10.0
0.0
0.00
20.00
40.00
60.00
80.00
OUTPUT SOURCE CURRENT VS. OUTPUT VOLTAGE
(VCC = 5V, TA = 25°C)
100.00
FREQUENCY (MHz)
0.0
-10.0
OUTPUT SOURCE CURRENT VS. SUPPLY VOLTAGE
(VOH = 2.4V, TA = 25°C)
-20.0
-30.0
IOH (mA)
0.0
-10.0
IOH (mA)
-20.0
-40.0
-50.0
-60.0
-70.0
-80.0
-30.0
-90.0
-100.0
-40.0
0.00
0.50
1.00
1.50
2.00
2.50
3.00
3.50
4.00
4.50
5.00
OUTPUT VOLTAGE (V)
-50.0
-60.0
4.50
4.75
5.00
5.25
5.50
SUPPLY VOLTAGE (V)
17
0995K–PLD–6/05
INPUT CLAMP CURRENT VS. INPUT VOLTAGE
(VCC = 5V, TA = 25°C)
INPUT CURRENT VS. INPUT VOLTAGE
(VCC = 5V, TA = 25°C)
40
0
30
INPUT CURRENT (mA)
INPUT CURRENT (mA)
-10
20
-20
10
-30
-40
0
-10
-50
-20
-60
-1.00
-30
-0.80
-0.60
-0.40
-0.20
0.00
0.0
0.5
1.0
1.5
INPUT VOLTAGE (V)
2.0
2.5
3.0
INPUT VOLTAGE (V)
3.5
4.0
4.5
5.0
OUTPUT SINK CURRENT VS. OUTPUT VOLTAGE
(VCC = 5V, TA = 25°C)
OUTPUT SINK CURRENT VS. SUPPLY VOLTAGE
(VOL = 0.5V, TA = 25°C)
140.0
43
120.0
42
100.0
IOL (mA)
41
IOL (mA)
40
39
80.0
60.0
38
40.0
37
36
20.0
35
34
4.50
0.0
0.00
4.75
5.00
5.25
0.50
1.00
1.50
5.50
2.00
2.50
3.00
3.50
4.00
4.50
5.00
OUTPUT VOLTAGE (V)
SUPPLY VOLTAGE (V)
NORMALIZED TPD
VS. TEMPERATURE (VCC = 5.0V)
NORMALIZED TPD
VS. SUPPLY VOLTAGE (TA = 25°C)
1.2
NORMALIZED TPD
NORMALIZED TPD
1.20
1.10
1.00
1.1
1.0
0.9
0.90
0.8
-40.0
0.80
0.0
25.0
75.0
TEMPERATURE (C)
4.5
4.8
5.0
5.3
5.5
SUPPLY VOLTAGE (V)
18
ATF1502AS(L)
0995K–PLD–6/05
ATF1502AS(L)
NORMALIZED TCO
VS. TEMPERATURE (VCC = 5.0V)
1.2
1.2
1.1
1.1
NORMALIZED TCO
NORMALIZED TPD
NORMALIZED TCO
VS. SUPPLY VOLTAGE (TA = 25°C)
1.0
1.0
0.9
0.9
0.8
-40.0
0.8
4.5
4.8
5.0
5.3
5.5
0.0
25.0
75.0
TEMPERATURE (C)
SUPPLY VOLTAGE (V)
NORMALIZED TSU VS. SUPPLY VOLTAGE (TA = 25°C)
1.2
NORMALIZED TSU
VS. TEMPERATURE (VCC = 5.0V)
1.2
NORMALIZED TSU
NORMALIZED TSU
1.1
1.0
0.9
1.1
1.0
0.9
0.8
4.5
4.8
5.0
SUPPLY VOLTAGE (V)
5.3
5.5
0.8
-40.0
0.0
25.0
75.0
TEMPERATURE (C)
19
0995K–PLD–6/05
ATF1502AS Dedicated Pinouts
44-lead
TQFP
44-lead
J-lead
INPUT/OE2/GCLK2
40
2
INPUT/GCLR
39
1
INPUT/OE1
38
44
INPUT/GCLK1
37
43
I/O / GCLK3
35
41
I/O / PD (1,2)
5, 19
11, 25
I/O / TDI (JTAG)
1
7
I/O / TMS (JTAG)
7
13
I/O / TCK (JTAG)
26
32
I/O / TDO (JTAG)
32
38
GND
4, 16, 24, 36
10, 22, 30, 42
VCC
9, 17, 29, 41
3, 15, 23, 35
# of Signal Pins
36
36
# User I/O Pins
32
32
Dedicated Pin
OE (1, 2)
Global OE pins
GCLR
Global Clear pin
GCLK (1, 2, 3)
Global Clock pins
PD (1, 2)
Power-down pins
TDI, TMS, TCK, TDO
JTAG pins used for boundary-scan testing or in-system programming
GND
Ground pins
VCC
VCC pins for the device (+5V)
20
ATF1502AS(L)
0995K–PLD–6/05
ATF1502AS(L)
ATF1502AS I/O Pinouts
MC
PLC
44-lead PLCC
44-lead TQFP
1
A
4
42
2
A
5
43
3
A/PD1
6
44
4/TDI
A
7
1
5
A
8
2
6
A
9
3
7
A
11
5
8
A
12
6
9/TMS
A
13
7
10
A
14
8
11
A
16
10
12
A
17
11
13
A
18
12
14
A
19
13
15
A
20
14
16
A
21
15
17
B
41
35
18
B
40
34
19
B
39
33
20/TDO
B
38
32
21
B
37
31
22
B
36
30
23
B
34
28
24
B
33
27
25/TCK
B
32
26
26
B
31
25
27
B
29
23
28
B
28
22
29
B
27
21
30
B
26
20
31
B
25
19
32
B
24
18
21
0995K–PLD–6/05
Ordering Information
Standard Package Options
tPD
(ns)
tCO1
(ns)
fMAX
(MHz)
7.5
4.5
166.7
10
15
25
5
8
13
125
100
60
Ordering Code
Package
ATF1502AS-7 AC44
ATF1502AS-7 JC44
44A
44J
Commercial
(0°C to 70°C)
ATF1502AS-10 AC44
ATF1502AS-10 JC444
44A
44J
Commercial
(0°C to 70°C)
ATF1502AS-10 AI44
ATF1502AS-10 JI44
44A
44J
Industrial
(-40°C to +85°C)
ATF1502AS-15 AC44
ATF1502AS-15 JC44
44A
44J
Commercial
(0°C to 70°C)
ATF1502AS-15 AI44
ATF1502AS-15 JI44
44A
44J
Industrial
(-40°C to +85°C)
ATF1502ASL-25 AC44
ATF1502ASL-25 JC44
44A
44J
Commercial
(0°C to 70°C)
ATF1502ASL-25 AI44
44A
44J
Industrial
(-40°C to +85°C)
ATF1502ASL-25 JI44
Notes:
Operation Range
1. The last time buy date is Sept. 30, 2005 for shaded parts.
2. In 2004, Atmel briefly offered the lead-free products ATF1502AS-7JL44 and ATF1502AS-10JJ44. They have since been discontinued effective Sept. 30,2005 and replaced with Green “U” packages.
Using “C” Product for Industrial
To use commercial product for industrial temperature ranges, down-grade one speed grade from the “I” to the “C” device
(7 ns “C” = 10 ns “I”) and de-rate power by 30%.
Green Package Options (Pb/Halide-free/RoHS Compliant)
tPD
(ns)
tCO1
(ns)
fMAX
(MHz)
7.5
4.5
10
25
Ordering Code
Package
Operation Range
166.7
ATF1502AS-7 AX44
ATF1502AS-7 JX44
44A
44J
Commercial
(0°C to 70°C)
5
125
ATF1502AS-10 AU44
ATF1502AS-10 JU44
44A
44J
Industrial
(-40°C to +85°C)
13
60
ATF1502ASL-25 AU44
ATF1502ASL-25 JU44
44A
44J
Industrial
(-40°C to +85°C)
Package Type
44A
44-lead, Thin Plastic Gull Wing Quad Flatpack (TQFP)
44J
44-lead, Plastic J-leaded Chip Carrier OTP (PLCC)
22
ATF1502AS(L)
0995K–PLD–6/05
ATF1502AS(L)
Packaging Information
44A – TQFP
PIN 1
B
PIN 1 IDENTIFIER
E1
e
E
D1
D
C
0˚~7˚
A1
A2
A
L
COMMON DIMENSIONS
(Unit of Measure = mm)
Notes:
1. This package conforms to JEDEC reference MS-026, Variation ACB.
2. Dimensions D1 and E1 do not include mold protrusion. Allowable
protrusion is 0.25 mm per side. Dimensions D1 and E1 are maximum
plastic body size dimensions including mold mismatch.
3. Lead coplanarity is 0.10 mm maximum.
SYMBOL
MIN
NOM
MAX
A
–
–
1.20
A1
0.05
–
0.15
A2
0.95
1.00
1.05
D
11.75
12.00
12.25
D1
9.90
10.00
10.10
E
11.75
12.00
12.25
E1
9.90
10.00
10.10
B
0.30
–
0.45
C
0.09
–
0.20
L
0.45
–
0.75
e
NOTE
Note 2
Note 2
0.80 TYP
10/5/2001
R
2325 Orchard Parkway
San Jose, CA 95131
TITLE
44A, 44-lead, 10 x 10 mm Body Size, 1.0 mm Body Thickness,
0.8 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP)
DRAWING NO.
REV.
44A
B
23
0995K–PLD–6/05
44J – PLCC
1.14(0.045) X 45˚
PIN NO. 1
1.14(0.045) X 45˚
0.318(0.0125)
0.191(0.0075)
IDENTIFIER
E1
D2/E2
B1
E
B
e
A2
D1
A1
D
A
0.51(0.020)MAX
45˚ MAX (3X)
COMMON DIMENSIONS
(Unit of Measure = mm)
Notes:
1. This package conforms to JEDEC reference MS-018, Variation AC.
2. Dimensions D1 and E1 do not include mold protrusion.
Allowable protrusion is .010"(0.254 mm) per side. Dimension D1
and E1 include mold mismatch and are measured at the extreme
material condition at the upper or lower parting line.
3. Lead coplanarity is 0.004" (0.102 mm) maximum.
SYMBOL
MIN
NOM
MAX
A
4.191
–
4.572
A1
2.286
–
3.048
A2
0.508
–
–
D
17.399
–
17.653
D1
16.510
–
16.662
E
17.399
–
17.653
E1
16.510
–
16.662
D2/E2
14.986
–
16.002
B
0.660
–
0.813
B1
0.330
–
0.533
e
NOTE
Note 2
Note 2
1.270 TYP
10/04/01
R
24
2325 Orchard Parkway
San Jose, CA 95131
TITLE
44J, 44-lead, Plastic J-leaded Chip Carrier (PLCC)
DRAWING NO.
REV.
44J
B
ATF1502AS(L)
0995K–PLD–6/05
ATF1502AS(L)
Revision History
Revision
Comments
0995K
Green package options added.
25
0995K–PLD–6/05
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Regional Headquarters
Europe
Atmel Sarl
Route des Arsenaux 41
Case Postale 80
CH-1705 Fribourg
Switzerland
Tel: (41) 26-426-5555
Fax: (41) 26-426-5500
Asia
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimshatsui
East Kowloon
Hong Kong
Tel: (852) 2721-9778
Fax: (852) 2722-1369
Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
Tel: (81) 3-3523-3551
Fax: (81) 3-3523-7581
Atmel Operations
Memory
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
RF/Automotive
Theresienstrasse 2
Postfach 3535
74025 Heilbronn, Germany
Tel: (49) 71-31-67-0
Fax: (49) 71-31-67-2340
Microcontrollers
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
La Chantrerie
BP 70602
44306 Nantes Cedex 3, France
Tel: (33) 2-40-18-18-18
Fax: (33) 2-40-18-19-60
ASIC/ASSP/Smart Cards
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Biometrics/Imaging/Hi-Rel MPU/
High Speed Converters/RF Datacom
Avenue de Rochepleine
BP 123
38521 Saint-Egreve Cedex, France
Tel: (33) 4-76-58-30-00
Fax: (33) 4-76-58-34-80
Zone Industrielle
13106 Rousset Cedex, France
Tel: (33) 4-42-53-60-00
Fax: (33) 4-42-53-60-01
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Scottish Enterprise Technology Park
Maxwell Building
East Kilbride G75 0QR, Scotland
Tel: (44) 1355-803-000
Fax: (44) 1355-242-743
Literature Requests
www.atmel.com/literature
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT
OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications
and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided
otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use
as components in applications intended to support or sustain life.
© Atmel Corporation 2005. All rights reserved. Atmel®, logo and combinations thereof, Everywhere You Are ® and others, are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.
Printed on recycled paper.
0995K–PLD–6/05
xM
Similar pages