MPV1580L Series Compact PV Power, 15W 200 - 1500V Input DC/DC Converters Electrical Specifications Key Features: • 15W Output Power • 200 - 1500 VDC Input Range • 4,000 VAC Isolation • Compact Case Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Input Parameter Input Voltage Range Input Start Voltage Under Voltage Shutdown • Input Under Volt Protection • Output Over Volt Protection Inrush Current Start-Up Time • -25°C to +70°C Operation Output • >300 kHours MTBF Min. 200 180 170 200 VDC Input 1500 VDC Input 200 VDC Input 1500 VDC Input Input Current • Short Circuit Protection Conditions Parameter Output Voltage Accuracy Line Regulation Load Regulation Ripple & Noise (20 MHz) Temperature Coefficient Over Power Protection Output Short Circuit Conditions Typ. Max. 1,500 195 185 130 25 Units VDC VDC VDC mA 50 150 Min. VIN = MIN to MAX IOUT = 0% to 100% See Note 1 Typ. ±2.0 ±1.0 ±1.0 150 ±0.02 A 2.0 S Max. Units % % % mV P - P %/°C %IOUT 300 Autorecovery 120 Continuous (Autorecovery) General Parameter Isolation Voltage Switching Frequency EMI Characteristics Parameter Radiated Emissions, See Note 2 Conducted Emissions, See Note 2 ESD RS EFT, See Note 3 Surge, See Note 4 CS Conditions 60 Seconds Min. 4,000 Typ. Max. 65 Standard Criteria EN 55022 EN 55022 EN 61000-4-2 EN 61000-4-3 EN 61000-4-4 EN 61000-4-5 EN 61000-4-6 B A B B A Units VAC kHz Level Class A Class A ±6 kV/±8 10V/m ±2 kV ±1 kV 10 Vrms Environmental MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA Parameter Operating Temperature Range Storage Temperature Range Cooling Humidity Physical Case Size Case Material Weight Conditions Min. Typ. -25 +25 -25 Free Air Convection RH, Non-condensing Ambient Max. +70 +85 Units °C °C 95 % See Mechanical Drawings (Page 3) Black, Flame Retardant, Non-Conductive Plastic (UL94-V0) 9.57 Oz (270g) Reliability Specifications T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Parameter MTBF Conditions MIL HDBK 217F, 25°C, Gnd Benign Min. 300 Typ. Max. Units kHours Conditions Wave Soldering (5-10S) Manual Soldering (3-5S) Min. 255 350 Typ. 260 360 Max. 265 370 Units Absolute Maximum Ratings Parameter Lead Temperature, See Note 5 Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. www.micropowerdirect.com °C www.micropowerdirect.com Model Selection Guide Input Model Number Voltage (VDC) Output Efficiency Voltage Current (VDC) (mA, Max) Current (mA, Min) (%, Typ) Over Voltage Capacitive Load Protection (µF, Max) Fuse Rating Slow-Blow (mA) (VDC Typ) Nominal Range MPV1080LS-05RHI 800 200 - 1500 5.0 2,000 0.0 70 8.0 6,000 15A/1,500 VDC MPV1580LS-12RHI 800 200 - 1500 12.0 1,250 0.0 76 20.0 2,000 15A/1,500 VDC MPV1580LS-15RHI 800 200 - 1500 15.0 1,000 0.0 77 20.0 1,500 15A/1,500 VDC MPV1580LS-24RHI 800 200 - 1500 24.0 625 0.0 79 30.0 470 15A/1,500 VDC Notes: 1. To meet the specified ripple and noise levels, external capacitors are required. See the typical connection information on page three for recommended values. For more information, please contact the factory. 2. All units will meet EN 55022 (CE/RE) class A with the input circuit shown in the “Typical Connection 2” diagram on page 3. Contact the factory for more information. 3. All units will meet EN 61000-4-4 (±2 kV) with the input circuit shown in the “Typical Connection 2” diagram on page 3. Contact the factory for more information. 4. All units will meet the requirements of EN 61000-4-5 (±1 kV), with the input circuit shown in the “Typical Connection 2” diagram on page 3. Contact the factory for more information. 5. Lead temperature is measured 1.5 mm from the case. 6. Operation at no load will not damage the units, however, they may not meet all specifications. 7. It is recommended that a fuse be used on the input of a power supply for protection. For the MPV1580L-xxRHI series, a 15A/1,500 VDC slow blow should be used. Derating Curve: Temperature (Input = 200 - 1500 VDC) Efficiency Vs Input Voltage - Full Load MicroPower Direct • 292 Page Street Ste D Stoughton, MA 02072 Derating Curve: Altitude Efficiency Vs Output Load - VIN = 800V • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected] www.micropowerdirect.com Typical Connection 1 The diagram at left illustrates a typical connection of the MPV1580LS-xxRHI series. Output capacitors C9 and C10 are filtering components. Capacitor C9 is a ceramic and C10 is a high frequency, low resistance electrolytic. The TVS is recommended to protect circuit components if there is a fault with the converter. The recommended component values are given in the table below. Typical Connection 2: With External EMC Components Recommended values for components are: Model LDM LCM C1, C2, C3, C4 C5, C6, C7, C8 R1, R2, R3, R4 C9 C10 TVS SMBJ7.0A MPV1080LS-05RHI MPV1580LS-12RHI MPV1580LS-15RHI For applications that require meeting higher EMC standards, the circuit shown at left is recommended. Some notes on this diagram (starting with the input circuit) are: 1. It is recommended that an external fuse be used. The recommended fuse is 15A/1,500V. 2. Capacitors C1, C2, C3 and C4 are input filter components (connected in series to achieve the required capacitance level). 3. Capacitors C5, C6, C7 and C8 are also input filter components. Resistors R1, R2, R3 and R4 help to balance the current across the capacitors. 4. Capacitor C9 is ceramic. This capacitor is used to filter high frequency noise. A recommended value is given in the table below. 5. Capacitor C10 is an electrolytic. A low ESR, high frequency capacitor should be used.The recommended value is given in the table below. 6. The output TVS will help protect system circuitry if the converter fails. A recommended value is given in the table below. 7. Derating on all capacitors should be 80% or more. 330 µH/1A 7 mH/1A 0.1 μF/275 VAC 47 μF/450V 1 M⍀/2W 1.0 μF/50V 120 μF/25V 68 μF/35V MPV1580LS-24RHI SMBJ20A SMBJ30A Mechanical Dimensions Pin Connections Pin 1 2 3 4 5 6 Function +VIN -VIN No Connection No Connection -VOUT +VOUT Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.02 (±0.50) MicroPower Direct We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]