TI1 ISO7760DBQ High-speed, robust emc, reinforced six-channel digital isolator Datasheet

Product
Folder
Order
Now
Support &
Community
Tools &
Software
Technical
Documents
ISO7760, ISO7761
ISO7762, ISO7763
SLLSER1C – AUGUST 2017 – REVISED JANUARY 2018
ISO776x High-Speed, Robust EMC, Reinforced Six-Channel Digital Isolators
1 Features
•
•
•
•
•
•
1
•
•
•
•
•
•
•
•
Signaling Rate: Up to 100 Mbps
Wide Supply Range: 2.25 V to 5.5 V
2.25-V to 5.5-V Level Translation
Default Output High and Low Options
Wide Temperature Range: –55°C to +125°C
Low Power Consumption, Typical 1.4 mA per
Channel at 1 Mbps
Low Propagation Delay: 11 ns Typical
(5-V Supplies)
High CMTI: ±100 kV/μs Typical
Robust Electromagnetic Compatibility (EMC)
System-Level ESD, EFT, and Surge Immunity
Low Emissions
Isolation Barrier Life: >40 Years
Wide-SOIC (DW-16) and SSOP (DBQ-16)
Package Options
Safety-Related Certifications:
– Reinforced Insulation per DIN V VDE V 088411:2017-01
– UL 1577 Component Recognition Program
– CSA Certification according to IEC 60950-1,
IEC 62368-1 and IEC 60601-1 End Equipment
Standards
– CQC Certification per GB4943.1-2011
– TUV Certification according to EN 60950-1 and
EN 61010-1
– All Certifications are Planned
The ISO776x family of devices provides highelectromagnetic immunity and low emissions at lowpower consumption, while isolating CMOS or
LVCMOS digital I/Os. Each isolation channel has a
logic-input and logic-output buffer separated by a
silicon dioxide (SiO2) insulation barrier. The ISO776x
family of devices is available in all possible pin
configurations such that all six channels are in the
same direction, or one, two, or three channels are in
reverse direction while the remaining channels are in
forward direction. If the input power or signal is lost,
the default output is high for devices without suffix F
and low for devices with suffix F. See the Device
Functional Modes section for further details.
Used in conjunction with isolated power supplies, this
family of devices helps prevent noise currents on a
data bus or other circuits from entering the local
ground and interfering with or damaging sensitive
circuitry. Through innovative chip design and layout
techniques, electromagnetic compatibility of the
ISO776x family of devices has been significantly
enhanced to ease system-level ESD, EFT, surge, and
emissions compliance. The ISO776x family of
devices is available in 16-pin SOIC and SSOP
packages.
Device Information(1)
PART NUMBER
ISO7760
ISO7761
ISO7762
IOS7763
Factory Automation and Control
Test and Measurement
Telecom Infrastructure
Grid Infrastructure
Medical, Healthcare, and Fitness
3 Description
The ISO776x devices are high-performance, sixchannel digital isolators with 5000-VRMS (DW
package) and 3000-VRMS (DBQ package) isolation
ratings per UL 1577. This family of devices is also
certified according to VDE, CSA, TUV and CQC.
BODY SIZE (NOM)
10.30 mm × 7.50 mm
SSOP (16)
4.90 mm × 3.90 mm
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
Simplified Schematic
2 Applications
•
•
•
•
•
PACKAGE
SOIC (16)
VCCO
VCCI
Isolation
Capacitor
INx
OUTx
GNDI
GNDO
Copyright © 2016, Texas Instruments Incorporated
VCCI and GNDI are the supply and ground
connections respectively for the input
channels.
VCCO and GNDO are the supply and
ground connections respectively for the
output channels.
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
ISO7760, ISO7761
ISO7762, ISO7763
SLLSER1C – AUGUST 2017 – REVISED JANUARY 2018
www.ti.com
Table of Contents
1
2
3
4
5
6
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
6.10
6.11
6.12
6.13
6.14
6.15
6.16
6.17
6.18
1
1
1
2
3
5
Absolute Maximum Ratings ...................................... 5
ESD Ratings.............................................................. 5
Recommended Operating Conditions....................... 5
Thermal Information .................................................. 6
Power Ratings........................................................... 6
Insulation Specifications............................................ 7
Safety-Related Certifications..................................... 8
Safety Limiting Values .............................................. 8
Electrical Characteristics—5-V Supply ..................... 9
Supply Current Characteristics—5-V Supply ........ 10
Electrical Characteristics—3.3-V Supply .............. 11
Supply Current Characteristics—3.3-V Supply ..... 12
Electrical Characteristics—2.5-V Supply .............. 13
Supply Current Characteristics—2.5-V Supply ..... 14
Switching Characteristics—5-V Supply................. 15
Switching Characteristics—3.3-V Supply.............. 15
Switching Characteristics—2.5-V Supply.............. 16
Insulation Characteristics Curves ......................... 17
6.19 Typical Characteristics .......................................... 18
7
8
Parameter Measurement Information ................ 21
Detailed Description ............................................ 22
8.1
8.2
8.3
8.4
9
Overview .................................................................
Functional Block Diagram .......................................
Feature Description.................................................
Device Functional Modes........................................
22
22
23
24
Application and Implementation ........................ 25
9.1 Application Information............................................ 25
9.2 Typical Application .................................................. 25
10 Power Supply Recommendations ..................... 28
11 Layout................................................................... 29
11.1 Layout Guidelines ................................................. 29
11.2 Layout Example .................................................... 29
12 Device and Documentation Support ................. 30
12.1
12.2
12.3
12.4
12.5
12.6
12.7
Documentation Support ........................................
Related Links ........................................................
Receiving Notification of Documentation Updates
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
30
30
30
30
30
30
31
13 Mechanical, Packaging, and Orderable
Information ........................................................... 31
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision B (November 2017) to Revision C
•
Page
Changed the CIO value for the DBQ package from 1.1 to 0.9 pF in the Insulation Specifications table ................................ 7
Changes from Revision A (August 2017) to Revision B
Page
•
Changed the CSA certification wording in the Features and Safety-Related Certifications table.......................................... 1
•
Changed the isolation voltage for the DBQ-16 package from 2500 to 3000 VRMS ................................................................. 1
•
Added the maximum transient isolation voltage for the DW-16 package of the ISO7761, ISO7762, and ISO7763
devices in the Insulation Specifications and Safety-Related Certifications tables. Also changed the maximum value
for the DBQ-16 package from 3600 to 4242 for all devcies ................................................................................................... 7
•
Changed the table note and table condition for the Safety Limiting Values........................................................................... 8
•
Added the supply current vs data rate graphs for the ISO7761, ISO7762, and ISO7763 in the Typical
Characteristics section.......................................................................................................................................................... 18
Changes from Original (August 2017) to Revision A
Page
•
Deleted EN from the Common-Mode Transient Immunity Test Circuit figure ...................................................................... 21
•
Changed the VCC1 and VCC2 signals in the Typical ISO7761 Circuit Hook-up figure............................................................ 27
2
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: ISO7760 ISO7761 ISO7762 ISO7763
ISO7760, ISO7761
ISO7762, ISO7763
www.ti.com
SLLSER1C – AUGUST 2017 – REVISED JANUARY 2018
5 Pin Configuration and Functions
ISO7760 DW and DBQ Packages
16-Pin SOIC and SSOP
Top View
ISO7761 DW and DBQ Packages
16-Pin SOIC and SSOP
Top View
16 VCC2
VCC1
1
16 VCC2
INA
2
15 OUTA
INA
2
15 OUTA
INB
3
14 OUTB
INB
3
14 OUTB
INC
4
13 OUTC
INC
4
IND
5
12 OUTD
IND
5
INE
6
11 OUTE
INE
6
INF
7
10 OUTF
OUTF 7
GND1 8
9 GND2
GND1 8
ISO7762 DW and DBQ Packages
16-Pin SOIC and SSOP
Top View
ISOLATION
1
ISOLATION
VCC1
13 OUTC
12 OUTD
11 OUTE
10
INF
9 GND2
ISO7763 DW and DBQ Packages
16-Pin SOIC and SSOP
Top View
16 VCC2
VCC1
1
16 VCC2
INA
2
15 OUTA
INA
2
15 OUTA
INB
3
14 OUTB
INB
3
14 OUTB
INC
4
13 OUTC
INC
4
IND
5
12 OUTD
OUTD 5
OUTE 6
11
INE
OUTF 7
10
INF
GND1 8
9 GND2
Copyright © 2017–2018, Texas Instruments Incorporated
ISOLATION
1
ISOLATION
VCC1
13 OUTC
12
IND
OUTE 6
11
INE
OUTF 7
10
INF
GND1 8
9 GND2
Submit Documentation Feedback
Product Folder Links: ISO7760 ISO7761 ISO7762 ISO7763
3
ISO7760, ISO7761
ISO7762, ISO7763
SLLSER1C – AUGUST 2017 – REVISED JANUARY 2018
www.ti.com
Pin Functions
PIN
NAME
NO.
I/O
DESCRIPTION
ISO7760
ISO7761
ISO7762
ISO7763
GND1
8
8
8
8
—
Ground connection for VCC1
GND2
9
9
9
9
—
Ground connection for VCC2
INA
2
2
2
2
I
Input, channel A
INB
3
3
3
3
I
Input, channel B
INC
4
4
4
4
I
Input, channel C
IND
5
5
5
12
I
Input, channel D
INE
6
6
11
11
I
Input, channel E
INF
7
10
10
10
I
Input, channel F
OUTA
15
15
15
15
O
Output, channel A
OUTB
14
14
14
14
O
Output, channel B
OUTC
13
13
13
13
O
Output, channel C
OUTD
12
12
12
5
O
Output, channel D
OUTE
11
11
6
6
O
Output, channel E
OUTF
10
7
7
7
O
Output, channel F
VCC1
1
1
1
1
—
Power supply, side 1
VCC2
16
16
16
16
—
Power supply, side 2
4
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: ISO7760 ISO7761 ISO7762 ISO7763
ISO7760, ISO7761
ISO7762, ISO7763
www.ti.com
SLLSER1C – AUGUST 2017 – REVISED JANUARY 2018
6 Specifications
6.1 Absolute Maximum Ratings
See
(1)
VCC1,
VCC2
Supply voltage (2)
MIN
MAX
–0.5
6
V
Voltage at INx, OUTx
–0.5
IO
Output current
–15
TJ
Junction temperature
Tstg
Storage temperature
(1)
(2)
(3)
UNIT
V
VCCX + 0.5
–65
(3)
V
15
mA
150
°C
150
°C
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values except differential I/O bus voltages are with respect to the local ground terminal (GND1 or GND2) and are peak
voltage values.
Maximum voltage must not exceed 6 V
6.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
Electrostatic discharge
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001
(1)
UNIT
±6000
Charged device model (CDM), per JEDEC specification JESD22-C101 (2)
V
±1500
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
MIN
VCC1, VCC2 Supply voltage
NOM
MAX
5.5
V
2
2.25
V
2.25
UNIT
VCC(UVLO+)
UVLO threshold when supply voltage is rising
VCC(UVLO-)
UVLO threshold when supply voltage is falling
1.7
1.8
V
VHYS(UVLO)
Supply voltage UVLO hysteresis
100
200
mV
IOH
IOL
High-level output current
Low-level output current
VCCO (1) = 5 V
–4
VCCO = 3.3 V
–2
VCCO = 2.5 V
–1
mA
VCCO = 5 V
4
VCCO = 3.3 V
2
VCCO = 2.5 V
1
mA
(1)
VCCI
Low-level input voltage
0
0.3 × VCCI
DR
Data rate
0
100
Mbps
TA
Ambient temperature
125
°C
VIH
High-level input voltage
VIL
(1)
0.7 × VCCI
–55
25
V
V
VCCI = Input-side VCC; VCCO = Output-side VCC.
Copyright © 2017–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: ISO7760 ISO7761 ISO7762 ISO7763
5
ISO7760, ISO7761
ISO7762, ISO7763
SLLSER1C – AUGUST 2017 – REVISED JANUARY 2018
www.ti.com
6.4 Thermal Information
ISO776x
THERMAL METRIC (1)
DW (SOIC)
DBQ (SSOP)
16 PINS
16 PINS
UNIT
RθJA
Junction-to-ambient thermal resistance
60.3
86.5
°C/W
RθJC(top)
Junction-to-case(top) thermal resistance
24.0
26.9
°C/W
RθJB
Junction-to-board thermal resistance
29.3
36.6
°C/W
ψJT
Junction-to-top characterization parameter
3.3
1.7
°C/W
ψJB
Junction-to-board characterization parameter
28.7
36.1
°C/W
n/a
n/a
°C/W
RθJC(bottom) Junction-to-case(bottom) thermal resistance
(1)
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
6.5 Power Ratings
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
ISO7760
PD
Maximum power dissipation (both sides)
VCC1 = VCC2 = 5.5 V, TJ = 150°C, CL = 15 pF,
input a 50-MHz 50% duty cycle square wave
292
mW
PD1
Maximum power dissipation (side 1)
VCC1 = VCC2 = 5.5 V, TJ = 150°C, CL = 15 pF,
input a 50-MHz 50% duty cycle square wave
50
mW
PD2
Maximum power dissipation (side 2)
VCC1 = VCC2 = 5.5 V, TJ = 150°C, CL = 15 pF,
input a 50-MHz 50% duty cycle square wave
242
mW
ISO7761
PD
Maximum power dissipation (both sides)
VCC1 = VCC2 = 5.5 V, TJ = 150°C, CL = 15 pF,
input a 50-MHz 50% duty cycle square wave
292
mW
PD1
Maximum power dissipation (side 1)
VCC1 = VCC2 = 5.5 V, TJ = 150°C, CL = 15 pF,
input a 50-MHz 50% duty cycle square wave
83
mW
PD2
Maximum power dissipation (side 2)
VCC1 = VCC2 = 5.5 V, TJ = 150°C, CL = 15 pF,
input a 50-MHz 50% duty cycle square wave
209
mW
ISO7762
PD
Maximum power dissipation (both sides)
VCC1 = VCC2 = 5.5 V, TJ = 150°C, CL = 15 pF,
input a 50-MHz 50% duty cycle square wave
292
mW
PD1
Maximum power dissipation (side 1)
VCC1 = VCC2 = 5.5 V, TJ = 150°C, CL = 15 pF,
input a 50-MHz 50% duty cycle square wave
116
mW
PD2
Maximum power dissipation (side 2)
VCC1 = VCC2 = 5.5 V, TJ = 150°C, CL = 15 pF,
input a 50-MHz 50% duty cycle square wave
176
mW
ISO7763
PD
Maximum power dissipation (both sides)
VCC1 = VCC2 = 5.5 V, TJ = 150°C, CL = 15 pF,
input a 50-MHz 50% duty cycle square wave
292
mW
PD1
Maximum power dissipation (side 1)
VCC1 = VCC2 = 5.5 V, TJ = 150°C, CL = 15 pF,
input a 50-MHz 50% duty cycle square wave
146
mW
PD2
Maximum power dissipation (side 2)
VCC1 = VCC2 = 5.5 V, TJ = 150°C, CL = 15 pF,
input a 50-MHz 50% duty cycle square wave
146
mW
6
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: ISO7760 ISO7761 ISO7762 ISO7763
ISO7760, ISO7761
ISO7762, ISO7763
www.ti.com
SLLSER1C – AUGUST 2017 – REVISED JANUARY 2018
6.6 Insulation Specifications
VALUE
PARAMETER
TEST CONDITIONS
CLR
External clearance (1)
CPG
External clearance
(1)
DTI
Distance through the insulation
CTI
Tracking resistance (comparative
DIN EN 60112 (VDE 0303-11); IEC 60112; UL 746A
tracking index)
Material group
DW-16
Shortest terminal-to-terminal distance through air
DBQ- UNIT
16
>8
>3.7
mm
Shortest terminal-to-terminal distance across the package surface
>8
>3.7
mm
Minimum internal gap (internal clearance)
>21
>21
μm
>600
>600
V
According to IEC 60664-1
I
I
Rated mains voltage ≤ 150 VRMS
I–IV
I–IV
Rated mains voltage ≤ 300 VRMS
I–IV
I–III
Rated mains voltage ≤ 600 VRMS
I–IV
n/a
Rated mains voltage ≤ 1000 VRMS
I–III
n/a
AC voltage (bipolar)
1414
566
VPK
AC voltage; Time dependent dielectric breakdown (TDDB) test
1000
400
VRMS
DC voltage
1414
566
VDC
4242
VPK
8000
4000
VPK
Method a, After Input/Output safety test subgroup 2/3,
Vini = VIOTM, tini = 60 s;
Vpd(m) = 1.2 × VIORM, tm = 10 s
≤5
≤5
Method a, After environmental tests subgroup 1,
Vini = VIOTM, tini = 60 s;
Vpd(m) = 1.6 × VIORM, tm = 10 s
≤5
≤5
Method b1; At routine test (100% production) and preconditioning (type
test)
Vini = 1.2 x VIOTM, tini = 1 s;
Vpd(m) = 1.875 × VIORM, tm = 1 s
≤5
≤5
VIO = 0.4 × sin (2πft), f = 1 MHz
~1.1
~0.9
VIO = 500 V, TA = 25°C
>1012
>1012
11
>1011
9
>10
>109
Pollution degree
2
2
Climatic category
55/125/
21
55/12
5/
21
5000
3000
Overvoltage category per IEC
60664-1
DIN V VDE V 0884-11:2017-01 (2)
VIORM
Maximum repetitive peak
isolation voltage
VIOWM
Maximum working isolation
voltage
VIOTM
Maximum transient isolation
voltage
VTEST = VIOTM , t = 60 s (qualification)
VTEST = 1.2 x VIOTM, t = 1 s (100%
production)
VIOSM
Maximum surge isolation
voltage (3)
Test method per IEC 62368-1, 1.2/50 µs waveform,
VTEST = 1.6 × VIOSM (qualification)
Apparent charge (4)
qpd
Barrier capacitance, input to
output (5)
CIO
RIO
Isolation resistance
(5)
ISO7760
8000
ISO7761, ISO7762, ISO7763
7071
VIO = 500 V, 100°C ≤ TA ≤ 125°C
>10
VIO = 500 V, TS = 150°C
pC
pF
Ω
UL 1577
VISO
(1)
(2)
(3)
(4)
(5)
Withstanding isolation voltage
VTEST = VISO , t = 60 s (qualification),
VTEST = 1.2 × VISO , t = 1 s (100% production)
VRMS
Creepage and clearance requirements should be applied according to the specific equipment isolation standards of an application. Care
should be taken to maintain the creepage and clearance distance of a board design to ensure that the mounting pads of the isolator on
the printed-circuit board do not reduce this distance. Creepage and clearance on a printed-circuit board become equal in certain cases.
Techniques such as inserting grooves and/or ribs on a printed circuit board are used to help increase these specifications.
This coupler is suitable for safe electrical insulation only within the safety ratings. Compliance with the safety ratings shall be ensured by
means of suitable protective circuits
Testing is carried out in air or oil to determine the intrinsic surge immunity of the isolation barrier.
Apparent charge is electrical discharge caused by a partial discharge (pd).
All pins on each side of the barrier tied together creating a two-terminal device.
Copyright © 2017–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: ISO7760 ISO7761 ISO7762 ISO7763
7
ISO7760, ISO7761
ISO7762, ISO7763
SLLSER1C – AUGUST 2017 – REVISED JANUARY 2018
www.ti.com
6.7 Safety-Related Certifications
VDE
CSA
UL
CQC
TUV
Plan to certify according to
UL 1577 Component
Recognition Program
Plan to certify according to
GB 4943.1-2011
Plan to certify according
to EN 61010-1:2010 (3rd
Ed) and EN 609501:2006/A11:2009/A1:201
0/A12:2011/A2:2013
5000 VRMS Reinforced
insulation per EN 610101:2010 (3rd Ed) up to
working voltage of 600
VRMS (DW package)
5000 VRMS Reinforced
insulation per EN 609501:2006/A11:2009/A1:201
0/A12:2011/A2:2013 up
to working voltage of
800 VRMS (DW package)
Certification Planned
Plan to certify
according to DIN V
VDE V 0884-11:201701
Plan to certify according to
IEC 60950-1, IEC 62368-1
and IEC 60601-1
Maximum transient
isolation voltage, 8000
VPK (ISO7760 in DW16), 7071 VPK
(ISO7761, ISO7762,
ISO7763 in DW-16)
and 4242 VPK (DBQ16);
Maximum repetitive
peak isolation voltage,
1414 VPK (DW-16) and
566 VPK (DBQ-16);
Maximum surge
isolation voltage, 8000
VPK (DW-16) and 4000
VPK (DBQ-16)
Reinforced insulation per
CSA 60950-1-07+A1+A2
and IEC 60950-1 2nd Ed.,
800 VRMS (DW-16) and 370
VRMS (DBQ-16) maximum
working voltage (pollution
degree 2, material group I);
DW-16: 2 MOPP (Means of
Patient Protection) per CSA
60601-1:14 and IEC 60601-1
Ed. 3.1, 250 VRMS (DW-16)
maximum working voltage
DW-16: Single protection,
5000 VRMS ;
DBQ-16: Single protection,
3000 VRMS
DW-16: Reinforced
Insulation, Altitude ≤ 5000
m, Tropical Climate, 400
VRMS maximum working
voltage;
DBQ-16: Basic Insulation,
Altitude ≤ 5000 m, Tropical
Climate, 250 VRMS
maximum working voltage
Certification Planned
Certification Planned
Certification Planned
Certification Planned
6.8 Safety Limiting Values
Safety limiting intends to minimize potential damage to the isolation barrier upon failure of input or output circuitry.
PARAMETER
TEST CONDITIONS
MIN
TYP MAX
UNIT
DW-16 PACKAGE
IS
Safety input, output, or supply
current (1)
PS
Safety input, output, or total power
TS
Maximum safety temperature (1)
(1)
RθJA = 60.3 °C/W, VI = 5.5 V, TJ = 150°C, TA = 25°C,
see Figure 1
377
RθJA = 60.3 °C/W, VI = 3.6 V, TJ = 150°C, TA = 25°C,
see Figure 1
576
RθJA = 60.3 °C/W, VI = 2.75 V, TJ = 150°C, TA = 25°C,
see Figure 1
754
RθJA = 60.3 °C/W, TJ = 150°C, TA = 25°C, see Figure 3
2073
mW
150
°C
mA
DBQ-16 PACKAGE
IS
Safety input, output, or supply
current (1)
PS
Safety input, output, or total power (1)
TS
Maximum safety temperature (1)
(1)
RθJA = 86.5 °C/W, VI = 5.5 V, TJ = 150°C, TA = 25°C,
see Figure 2
263
RθJA = 86.5 °C/W, VI = 3.6 V, TJ = 150°C, TA = 25°C,
see Figure 2
401
RθJA = 86.5 °C/W, VI = 2.75 V, TJ = 150°C, TA = 25°C,
see Figure 2
525
RθJA = 86.5 °C/W, TJ = 150°C, TA = 25°C, see Figure 4
1445
mW
150
°C
mA
The maximum safety temperature, TS, has the same value as the maximum junction temperature, TJ, specified for the device. The IS
and PS parameters represent the safety current and safety power respectively. The maximum limits of IS and PS should not be
exceeded. These limits vary with the ambient temperature, TA.
The junction-to-air thermal resistance, RθJA, in the Thermal Information table is that of a device installed on a high-K test board for
leaded surface-mount packages. Use these equations to calculate the value for each parameter:
TJ = TA + RθJA × P, where P is the power dissipated in the device.
TJ(max) = TS = TA + RθJA × PS, where TJ(max) is the maximum allowed junction temperature.
PS = IS × VI, where VI is the maximum input voltage.
8
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: ISO7760 ISO7761 ISO7762 ISO7763
ISO7760, ISO7761
ISO7762, ISO7763
www.ti.com
SLLSER1C – AUGUST 2017 – REVISED JANUARY 2018
6.9 Electrical Characteristics—5-V Supply
VCC1 = VCC2 = 5 V ±10% (over recommended operating conditions unless otherwise noted)
PARAMETER
TEST CONDITIONS
VOH
High-level output voltage
IOH = –4 mA; see Figure 18
VOL
Low-level output voltage
IOL = 4 mA; see Figure 18
VIT+(IN)
Rising input threshold voltage
VIT-(IN)
Falling input threshold voltage
VI(HYS)
Input threshold voltage
hysteresis
(1)
IIH
High-level input current
VIH = VCCI
IIL
Low-level input current
VIL = 0 V at INx
CMTI
Common-mode transient
immunity
VI = VCCI or 0 V, VCM = 1200 V; see
Figure 20
CI
Input capacitance (2)
VI = VCC / 2 + 0.4 × sin (2πft), f = 1
MHz, VCC = 5 V
(1)
(2)
VCCO
(1)
MIN
TYP
– 0.4
4.8
MAX
UNIT
V
0.2
0.4
V
0.6 x VCCI
0.7 x VCCI
V
0.3 x VCCI
0.4 x VCCI
V
0.1 × VCCI
0.2 x VCCI
V
10
at INx
–10
85
μA
μA
100
2
kV/μs
pF
VCCI = Input-side VCC; VCCO = Output-side VCC.
Measured from input pin to ground.
Copyright © 2017–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: ISO7760 ISO7761 ISO7762 ISO7763
9
ISO7760, ISO7761
ISO7762, ISO7763
SLLSER1C – AUGUST 2017 – REVISED JANUARY 2018
www.ti.com
6.10 Supply Current Characteristics—5-V Supply
VCC1 = VCC2 = 5 V ±10% (over recommended operating conditions unless otherwise noted).
PARAMETER
SUPPLY
CURRENT
TEST CONDITIONS
MIN
TYP
MAX
UNIT
ISO7760
Supply current - DC
signal
VI = VCC1 (ISO7760);
VI = 0 V (ISO7760 with F suffix)
ICC1
1.6
2.3
ICC2
3
4.9
VI = 0 V (ISO7760);
VI = VCC1 (ISO7760 with F suffix)
ICC1
8
11.3
ICC2
3.3
5.3
ICC1
5
6.4
ICC2
3.5
5.6
ICC1
5.2
6.7
ICC2
6.4
9
ICC1
7
9
ICC2
35
44
VI = VCCI (1)(ISO7761);
VI = 0 V (ISO7761 with F suffix)
ICC1
1.9
2.7
ICC2
2.9
4.7
VI = 0 V (ISO7761);
VI = VCCI (ISO7761 with F suffix)
ICC1
7.3
10.6
ICC2
4.2
6.6
ICC1
4.7
6.4
ICC2
3.8
5.9
ICC1
5.3
7.2
ICC2
6.3
8.8
ICC1
11.5
15
ICC2
30.5
38
VI = VCCI (ISO7762);
VI = 0 V (ISO7762 with F suffix)
ICC1
2.1
3.2
ICC2
2.6
4.2
VI = 0 V (ISO7762);
VI = VCCI (ISO7762 with F suffix)
ICC1
6.5
9.3
ICC2
5
7.5
ICC1
4.5
6.3
ICC2
4
6.1
ICC1
5.6
7.6
ICC2
6
8.4
ICC1
16.5
21
ICC2
25.7
32
VI = VCCI (ISO7763);
VI = 0 V (ISO7763 with F suffix)
ICC1, ICC2
2.4
3.7
VI = 0 V (ISO7763);
VI = VCCI (ISO7763 with F suffix)
ICC1, ICC2
5.7
8.6
1 Mbps
ICC1, ICC2
4.2
6.1
10 Mbps
ICC1, ICC2
5.8
8
100 Mbps
ICC1, ICC2
21
26.5
1 Mbps
Supply current - AC
signal
All channels switching with square wave
clock input; CL = 15 pF
10 Mbps
100 Mbps
mA
mA
ISO7761
Supply current - DC
signal
1 Mbps
Supply current - AC
signal
All channels switching with square wave
clock input; CL = 15 pF
10 Mbps
100 Mbps
mA
mA
ISO7762
Supply current - DC
signal
1 Mbps
Supply current - AC
signal
All channels switching with square wave
clock input; CL = 15 pF
10 Mbps
100 Mbps
mA
mA
ISO7763
Supply current - DC
signal
Supply current - AC
signal
(1)
10
All channels switching with square wave
clock input; CL = 15 pF
mA
mA
VCCI = Input-side VCC
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: ISO7760 ISO7761 ISO7762 ISO7763
ISO7760, ISO7761
ISO7762, ISO7763
www.ti.com
SLLSER1C – AUGUST 2017 – REVISED JANUARY 2018
6.11 Electrical Characteristics—3.3-V Supply
VCC1 = VCC2 = 3.3 V ±10% (over recommended operating conditions unless otherwise noted)
PARAMETER
TEST CONDITIONS
VOH
High-level output voltage
IOH = –2 mA; see Figure 18
VOL
Low-level output voltage
IOL = 2 mA; see Figure 18
VCCO
(1)
MIN
TYP
– 0.3
3.2
UNIT
V
0.1
0.3
V
0.6 x VCCI
0.7 x
VCCI
V
VIT+(IN)
Rising input threshold voltage
VIT-(IN)
Falling input threshold voltage
0.3 x VCCI
0.4 x VCCI
VI(HYS)
Input threshold voltage hysteresis
0.1 × VCCI
0.2 x VCCI
IIH
High-level input current
VCCIIH = V (1) at INx
IIL
Low-level input current
VIL = 0 V at INx
CMTI
Common-mode transient
immunity
VI = VCCI or 0 V, VCM = 1200 V; see
Figure 20
(1)
MAX
V
V
10
μA
–10
85
μA
100
kV/μs
VCCI = Input-side VCC; VCCO = Output-side VCC.
Copyright © 2017–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: ISO7760 ISO7761 ISO7762 ISO7763
11
ISO7760, ISO7761
ISO7762, ISO7763
SLLSER1C – AUGUST 2017 – REVISED JANUARY 2018
www.ti.com
6.12 Supply Current Characteristics—3.3-V Supply
VCC1 = VCC2 = 3.3 V ±10% (over recommended operating conditions unless otherwise noted).
PARAMETER
SUPPLY
CURRENT
TEST CONDITIONS
MIN
TYP
MAX
UNIT
ISO7760
Supply current - DC
signal
VI = VCC1 (ISO7760);
VI = 0 V (ISO7760 with F suffix)
ICC1
1.6
2.2
ICC2
3
4.8
VI = 0 V (ISO7760);
VI = VCC1 (ISO7760 with F suffix)
ICC1
8
11.4
ICC2
3.3
5.3
ICC1
4.9
6.6
ICC2
3.4
5.3
ICC1
5
6.7
ICC2
5.5
7.8
ICC1
6.3
8.2
ICC2
26
33
VI = VCCI (1) (ISO7761);
VI = 0 V (ISO7761 with F suffix)
ICC1
1.8
2.7
ICC2
2.9
4.7
VI = 0 V (ISO7761);
VI = VCCI (ISO7761 with F suffix)
ICC1
7.2
10.3
ICC2
4.2
6.6
ICC1
4.6
6.5
ICC2
3.7
5.7
ICC1
5.1
7
ICC2
5.5
7.8
ICC1
9.4
12
ICC2
22.8
29
VI = VCCI (ISO7762);
VI = 0 V (ISO7762 with F suffix)
ICC1
2.1
3.2
ICC2
2.5
4.2
VI = 0 V (ISO7762);
VI = VCCI (ISO7762 with F suffix)
ICC1
6.5
9.4
ICC2
5
7.5
ICC1
4.4
6.2
ICC2
3.9
5.8
ICC1
5.2
7.1
ICC2
5.4
7.5
ICC1
12.9
16.5
ICC2
19.5
25
VI = VCCI (ISO7763);
VI = 0 V (ISO7763 with F suffix)
ICC1, ICC2
2.4
3.7
VI = 0 V (ISO7763);
VI = VCCI (ISO7763 with F suffix)
ICC1, ICC2
5.7
8.4
1 Mbps
ICC1, ICC2
4.2
6.2
10 Mbps
ICC1, ICC2
5.2
7.5
100 Mbps
ICC1, ICC2
16
20.5
1 Mbps
Supply current - AC
signal
All channels switching with square wave
clock input; CL = 15 pF
10 Mbps
100 Mbps
mA
mA
ISO7761
Supply current - DC
signal
1 Mbps
Supply current - AC
signal
All channels switching with square wave
clock input; CL = 15 pF
10 Mbps
100 Mbps
mA
mA
ISO7762
Supply current - DC
signal
1 Mbps
Supply current - AC
signal
All channels switching with square wave
clock input; CL = 15 pF
10 Mbps
100 Mbps
mA
mA
ISO7763
Supply current - DC
signal
Supply current - AC
signal
(1)
12
All channels switching with square wave
clock input; CL = 15 pF
mA
mA
VCCI = Input-side VCC
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: ISO7760 ISO7761 ISO7762 ISO7763
ISO7760, ISO7761
ISO7762, ISO7763
www.ti.com
SLLSER1C – AUGUST 2017 – REVISED JANUARY 2018
6.13 Electrical Characteristics—2.5-V Supply
VCC1 = VCC2 = 2.5 V ±10% (over recommended operating conditions unless otherwise noted)
PARAMETER
TEST CONDITIONS
VOH
High-level output voltage
IOH = –1 mA; see Figure 18
VOL
Low-level output voltage
IOL = 1 mA; see Figure 18
VCCO
(1)
MIN
TYP
– 0.2
2.45
UNIT
V
0.05
0.2
V
0.6 x VCCI
0.7 x
VCCI
V
VIT+(IN)
Rising input threshold voltage
VIT-(IN)
Falling input threshold voltage
0.3 x VCCI
0.4 x VCCI
VI(HYS)
Input threshold voltage hysteresis
0.1 × VCCI
0.2 x VCCI
IIH
High-level input current
VIH = VCCI (1) at INx
IIL
Low-level input current
VIL = 0 V at INx
CMTI
VI = VCCI or 0 V, VCM = 1200 V;
Common-mode transient immunity
see Figure 20
(1)
MAX
V
V
10
μA
–10
85
μA
100
kV/μs
VCCI = Input-side VCC; VCCO = Output-side VCC.
Copyright © 2017–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: ISO7760 ISO7761 ISO7762 ISO7763
13
ISO7760, ISO7761
ISO7762, ISO7763
SLLSER1C – AUGUST 2017 – REVISED JANUARY 2018
www.ti.com
6.14 Supply Current Characteristics—2.5-V Supply
VCC1 = VCC2 = 2.5 V ±10% (over recommended operating conditions unless otherwise noted).
PARAMETER
SUPPLY
CURRENT
TEST CONDITIONS
MIN
TYP
MAX
UNIT
ISO7760
Supply current - DC
signal
VI = VCC1 (ISO7760);
VI = 0 V (ISO7760 with F suffix)
ICC1
1.6
2.2
ICC2
3
4.8
VI = 0 V (ISO7760);
VI = VCC1 (ISO7760 with F suffix)
ICC1
8
11.6
ICC2
3.3
5.3
ICC1
4.9
6.8
ICC2
3.4
5.3
ICC1
5
7
ICC2
4.9
7.2
ICC1
6
8
ICC2
20.3
26
VI = VCCI (1) (ISO7761);
VI = 0 V (ISO7761 with F suffix)
ICC1
1.8
2.7
ICC2
2.9
4.6
VI = 0 V (ISO7761);
VI = VCCI (ISO7761 with F suffix)
ICC1
7.2
10.3
ICC2
4.2
6.5
ICC1
4.6
6.7
ICC2
3.7
5.8
ICC1
4.9
7.1
ICC2
5
7.3
ICC1
8.3
10.7
ICC2
18.1
24
VI = VCCI (ISO7762);
VI = 0 V (ISO7762 with F suffix)
ICC1
2.1
3.2
ICC2
2.6
4.1
VI = 0 V (ISO7762);
VI = VCCI (ISO7762 with F suffix)
ICC1
6.5
9.6
ICC2
4.9
7.5
ICC1
4.4
6.4
ICC2
3.9
5.8
ICC1
5
7.1
ICC2
5
7.1
ICC1
10.9
14.1
ICC2
15.6
20.1
VI = VCCI (ISO7763);
VI = 0 V (ISO7763 with F suffix)
ICC1, ICC2
2.3
3.7
VI = 0 V (ISO7763);
VI = VCCI (ISO7763 with F suffix)
ICC1, ICC2
5.7
8.4
1 Mbps
ICC1, ICC2
4.1
6.1
10 Mbps
ICC1, ICC2
4.9
7.1
100 Mbps
ICC1, ICC2
13
17
1 Mbps
Supply current - AC
signal
All channels switching with square wave
clock input; CL = 15 pF
10 Mbps
100 Mbps
mA
mA
ISO7761
Supply current - DC
signal
1 Mbps
Supply current - AC
signal
All channels switching with square wave
clock input; CL = 15 pF
10 Mbps
100 Mbps
mA
mA
ISO7762
Supply current - DC
signal
1 Mbps
Supply current - AC
signal
All channels switching with square wave
clock input; CL = 15 pF
10 Mbps
100 Mbps
mA
mA
ISO7763
Supply current - DC
signal
Supply current - AC
signal
(1)
14
All channels switching with square wave
clock input; CL = 15 pF
mA
mA
VCCI = Input-side VCC
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: ISO7760 ISO7761 ISO7762 ISO7763
ISO7760, ISO7761
ISO7762, ISO7763
www.ti.com
SLLSER1C – AUGUST 2017 – REVISED JANUARY 2018
6.15 Switching Characteristics—5-V Supply
VCC1 = VCC2 = 5 V ±10% (over recommended operating conditions unless otherwise noted)
PARAMETER
TEST CONDITIONS
tPLH, tPHL
Propagation delay time
PWD
Pulse width distortion (1) |tPHL – tPLH|
tsk(o)
Channel-to-channel output skew time (2)
tsk(pp)
Part-to-part skew time (3)
tr
Output signal rise time
tf
Output signal fall time
MAX
See Figure 18
Default output delay time from input power loss
tie
Time interval error
216 – 1 PRBS data at 100 Mbps
UNIT
11
16
ns
0.4
4.9
ns
4
ns
4.5
ns
1.1
3.9
ns
1.4
3.9
ns
0.2
0.3
μs
1.3
Same-direction channels
tDO
(3)
TYP
6
See Figure 18
Measured from the time VCC goes
below 1.7 V. See Figure 19
(1)
(2)
MIN
ns
Also known as pulse skew.
tsk(o) is the skew between outputs of a single device with all driving inputs connected together and the outputs switching in the same
direction while driving identical loads.
tsk(pp) is the magnitude of the difference in propagation delay times between any terminals of different devices switching in the same
direction while operating at identical supply voltages, temperature, input signals and loads.
6.16 Switching Characteristics—3.3-V Supply
VCC1 = VCC2 = 3.3 V ±10% (over recommended operating conditions unless otherwise noted)
PARAMETER
tPLH, tPHL
TEST CONDITIONS
Propagation delay time
(1)
PWD
Pulse width distortion
tsk(o)
Channel-to-channel output skew time (2)
tsk(pp)
Part-to-part skew time (3)
tr
Output signal rise time
tf
Output signal fall time
tDO
Measured from the time VCC
Default output delay time from input power loss
goes below 1.7 V. See Figure 19
tie
Time interval error
(1)
(2)
(3)
|tPHL – tPLH|
See Figure 18
MIN
TYP
MAX
6
12
16
ns
0.5
5
ns
4.1
ns
4.5
ns
1
3
ns
1
3
ns
0.2
0.3
μs
Same-direction channels
See Figure 18
216 – 1 PRBS data at 100 Mbps
UNIT
1.3
ns
Also known as pulse skew.
tsk(o) is the skew between outputs of a single device with all driving inputs connected together and the outputs switching in the same
direction while driving identical loads.
tsk(pp) is the magnitude of the difference in propagation delay times between any terminals of different devices switching in the same
direction while operating at identical supply voltages, temperature, input signals and loads.
Copyright © 2017–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: ISO7760 ISO7761 ISO7762 ISO7763
15
ISO7760, ISO7761
ISO7762, ISO7763
SLLSER1C – AUGUST 2017 – REVISED JANUARY 2018
www.ti.com
6.17 Switching Characteristics—2.5-V Supply
VCC1 = VCC2 = 2.5 V ±10% (over recommended operating conditions unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
tPLH, tPHL
Propagation delay time
PWD
Pulse width distortion (1) |tPHL – tPLH|
tsk(o)
Channel-to-channel output skew time (2)
tsk(pp)
Part-to-part skew time (3)
tr
Output signal rise time
tf
Output signal fall time
tDO
Measured from the time VCC
Default output delay time from input power loss
goes below 1.7 V. See Figure 19
tie
Time interval error
(1)
(2)
(3)
16
7.5
See Figure 18
TYP
MAX
UNIT
13
18.5
ns
0.6
5.1
ns
4.1
ns
4.6
ns
1
3.5
ns
1
3.5
ns
0.1
0.3
μs
Same-direction channels
See Figure 18
216 – 1 PRBS data at 100 Mbps
1.3
ns
Also known as pulse skew.
tsk(o) is the skew between outputs of a single device with all driving inputs connected together and the outputs switching in the same
direction while driving identical loads.
tsk(pp) is the magnitude of the difference in propagation delay times between any terminals of different devices switching in the same
direction while operating at identical supply voltages, temperature, input signals and loads.
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: ISO7760 ISO7761 ISO7762 ISO7763
ISO7760, ISO7761
ISO7762, ISO7763
www.ti.com
SLLSER1C – AUGUST 2017 – REVISED JANUARY 2018
6.18 Insulation Characteristics Curves
600
800
Safety Liming Current (mA)
700
Safety Liming Current (mA)
VCC1 = VCC2 = 2.75 V
VCC1 = VCC2 = 3.6 V
VCC1 = VCC2 = 5.5 V
600
500
400
300
200
100
0
VCC1 = VCC2 = 2.75 V
VCC1 = VCC2 = 3.6 V
VCC1 = VCC2 = 5.5 V
500
400
300
200
100
0
0
50
100
150
Ambient Temperature (qC)
200
0
50
D008
Figure 1. Thermal Derating Curve for Limiting Current per
VDE for DW-16 Package
100
150
Ambient Temperature (qC)
200
D009
Figure 2. Thermal Derating Curve for Limiting Current per
VDE for DBQ-16 Package
2500
1600
Safety Limiting Power (mW)
Safety Limiting Power (mW)
1400
2000
1500
1000
500
1200
1000
800
600
400
200
0
0
0
50
100
150
Ambient Temperature (qC)
200
D010
Figure 3. Thermal Derating Curve for Limiting Power per
VDE for DW-16 Package
Copyright © 2017–2018, Texas Instruments Incorporated
0
50
100
150
Ambient Temperature (qC)
200
D011
Figure 4. Thermal Derating Curve for Limiting Power per
VDE for DBQ-16 Package
Submit Documentation Feedback
Product Folder Links: ISO7760 ISO7761 ISO7762 ISO7763
17
ISO7760, ISO7761
ISO7762, ISO7763
SLLSER1C – AUGUST 2017 – REVISED JANUARY 2018
www.ti.com
6.19 Typical Characteristics
14
48
ICC1 at 2.5 V
ICC2 at 2.5 V
ICC1 at 3.3 V
ICC2 at 3.3 V
ICC1 at 5 V
ICC2 at 5 V
Supply Current (mA)
40
36
32
ICC1 at 2.5 V
ICC2 at 2.5 V
ICC1 at 3.3 V
ICC2 at 3.3 V
ICC1 at 5 V
ICC2 at 5 V
12
Supply Current (mA)
44
28
24
20
16
12
8
10
8
6
4
2
4
0
0
0
25
TA = 25°C
50
Data Rate (Mbps)
75
100
0
CL = 15 pF
50
Data Rate (Mbps)
TA = 25°C
Figure 5. ISO7760 Supply Current vs Data Rate
(With 15-pF Load)
75
100
D002
CL = No Load
Figure 6. ISO7760 Supply Current vs Data Rate
(With No Load)
14
48
ICC1 at 2.5 V
ICC2 at 2.5 V
ICC1 at 3.3 V
ICC2 at 3.3 V
ICC1 at 5 V
ICC2 at 5 V
40
36
32
ICC1 at 2.5 V
ICC2 at 2.5 V
ICC1 at 3.3 V
ICC2 at 3.3 V
ICC1 at 5 V
ICC2 at 5 V
12
Supply Current (mA)
44
Supply Current (mA)
25
D001
28
24
20
16
12
8
10
8
6
4
2
4
0
0
0
25
TA = 25°C
50
Data Rate (Mbps)
75
100
0
CL = 15 pF
50
Data Rate (Mbps)
TA = 25°C
Figure 7. ISO7761 Supply Current vs Data Rate
(With 15-pF Load)
75
100
D013
CL = No Load
Figure 8. ISO7761 Supply Current vs Data Rate
(With No Load)
14
48
ICC1 at 2.5 V
ICC2 at 2.5 V
ICC1 at 3.3 V
ICC2 at 3.3 V
ICC1 at 5 V
ICC2 at 5 V
40
36
32
ICC1 at 2.5 V
ICC2 at 2.5 V
ICC1 at 3.3 V
ICC2 at 3.3 V
ICC1 at 5 V
ICC2 at 5 V
12
Supply Current (mA)
44
Supply Current (mA)
25
D012
28
24
20
16
12
8
10
8
6
4
2
4
0
0
0
25
TA = 25°C
50
Data Rate (Mbps)
75
100
CL = 15 pF
Figure 9. ISO7762 Supply Current vs Data Rate
(With 15-pF Load)
18
Submit Documentation Feedback
0
25
D014
50
Data Rate (Mbps)
TA = 25°C
75
100
D015
CL = No Load
Figure 10. ISO7762 Supply Current vs Data Rate
(With No Load)
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: ISO7760 ISO7761 ISO7762 ISO7763
ISO7760, ISO7761
ISO7762, ISO7763
www.ti.com
SLLSER1C – AUGUST 2017 – REVISED JANUARY 2018
Typical Characteristics (continued)
14
48
ICC1 at 2.5 V
ICC2 at 2.5 V
ICC1 at 3.3 V
ICC2 at 3.3 V
ICC1 at 5 V
ICC2 at 5 V
40
Supply Current (mA)
36
32
ICC1 at 2.5 V
ICC2 at 2.5 V
ICC1 at 3.3 V
ICC2 at 3.3 V
ICC1 at 5 V
ICC2 at 5 V
12
Supply Current (mA)
44
28
24
20
16
12
8
10
8
6
4
2
4
0
0
0
25
50
Data Rate (Mbps)
TA = 25°C
75
100
0
CL = 15 pF
75
100
D017
CL = No Load
Figure 12. ISO7763 Supply Current vs Data Rate
(With No Load)
1
6
VCC = 2.5 V
VCC = 3.3 V
VCC = 5 V
0.9
5
Low-Level Output Voltage (V)
High-Level Output Voltage (V)
50
Data Rate (Mbps)
TA = 25°C
Figure 11. ISO7763 Supply Current vs Data Rate
(With 15-pF Load)
4
3
2
VCC = 2.5 V
VCC = 3.3 V
VCC = 5 V
1
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
0
-15
-10
-5
High-Level Output Current (mA)
0
0
14
VCC1 Rising
VCC1 Falling
VCC2 Rising
VCC2 Falling
Propagation Delay Time (ns)
2.1
2.05
2
1.95
1.9
1.85
1.8
13
12
11
10
tPLH at 2.5 V
tPHL at 2.5 V
tPLH at 3.3 V
1.75
1.7
-60
D004
Figure 14. Low-Level Output Voltage vs Low-Level Output
Current
2.25
2.15
15
TA = 25°C
Figure 13. High-Level Output Voltage vs High-Level Output
Current
2.2
5
10
Low-Level Output Current (mA)
D003
TA = 25°C
Power-Supply UVLO Threshold (V)
25
D016
-30
0
30
60
Free-Air Temperature (qC)
90
9
-55
120
D005
Figure 15. Power Supply Undervoltage Threshold vs FreeAir Temperature
Copyright © 2017–2018, Texas Instruments Incorporated
-10
35
80
Free-Air Temperature (qC)
tPHL at 3.3 V
tPLH at 5 V
tPHL at 5 V
125
D006
Figure 16. Propagation Delay Time vs Free-Air Temperature
Submit Documentation Feedback
Product Folder Links: ISO7760 ISO7761 ISO7762 ISO7763
19
ISO7760, ISO7761
ISO7762, ISO7763
SLLSER1C – AUGUST 2017 – REVISED JANUARY 2018
www.ti.com
Typical Characteristics (continued)
Peak-to-Peak Output Jitter (ps)
1600
Rising Edge Jitter at 2.5 V
Falling Edge Jitter at 2.5 V
Rising Edge Jitter at 3.3 V
Falling Edge Jitter at 3.3 V
Rising Edge Jitter at 5 V
Falling Edge Jitter at 5 V
1400
1200
1000
800
600
0
25
50
Data Rate (Mbps)
75
100
D007
TA = 25°C
Figure 17. Peak-to-Peak Output Jitter vs Data Rate
20
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: ISO7760 ISO7761 ISO7762 ISO7763
ISO7760, ISO7761
ISO7762, ISO7763
www.ti.com
SLLSER1C – AUGUST 2017 – REVISED JANUARY 2018
7 Parameter Measurement Information
Isolation Barrier
IN
Input
Generator
(See Note A)
VI
VCCI
50
VI
OUT
50%
50%
0V
tPLH
tPHL
CL
See Note B
VO
VOH
90%
50%
VO
50%
10%
VOL
tf
tr
Copyright © 2016, Texas Instruments Incorporated
A.
The input pulse is supplied by a generator having the following characteristics: PRR ≤ 50 kHz, 50% duty cycle, tr ≤ 3
ns, tf ≤ 3 ns, ZO = 50 Ω. At the input, a 50-Ω resistor is required to terminate Input Generator signal. It is not needed
in actual application.
B.
CL = 15 pF and includes instrumentation and fixture capacitance within ±20%.
Figure 18. Switching Characteristics Test Circuit and Voltage Waveforms
VI
See Note B
VCC
VCC
Isolation Barrier
IN = 0 V (Devices without suffix F)
IN = VCC (Devices with suffix F)
VI
IN
1.7 V
0V
OUT
VO
tDO
CL
See Note A
default high
VOH
50%
VO
VOL
default low
A.
CL = 15 pF and includes instrumentation and fixture capacitance within ±20%.
B.
Power-supply ramp rate = 10 mV/ns
Figure 19. Default Output Delay Time Test Circuit and Voltage Waveforms
VCCI
VCCO
C = 0.1 µF ±1%
Pass-fail criteria:
The output must
remain stable.
Isolation Barrier
S1
C = 0.1 µF ±1%
IN
OUT
+
VOH or VOL
CL
See Note A
GNDI
A.
+
VCM ±
±
GNDO
CL = 15 pF and includes instrumentation and fixture capacitance within ±20%.
Figure 20. Common-Mode Transient Immunity Test Circuit
Copyright © 2017–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: ISO7760 ISO7761 ISO7762 ISO7763
21
ISO7760, ISO7761
ISO7762, ISO7763
SLLSER1C – AUGUST 2017 – REVISED JANUARY 2018
www.ti.com
8 Detailed Description
8.1 Overview
The ISO776x family of devices uses an ON-OFF keying (OOK) modulation scheme to transmit the digital data
across a silicon-dioxide based isolation barrier. The transmitter sends a high-frequency carrier across the barrier
to represent one digital state and sends no signal to represent the other digital state. The receiver demodulates
the signal after advanced signal conditioning and produces the output through a buffer stage. The ISO776x
family of devices also incorporates advanced circuit techniques to maximize the CMTI performance and minimize
the radiated emissions because of the high-frequency carrier and IO buffer switching. The conceptual block
diagram of a digital capacitive isolator, Figure 21, shows a functional block diagram of a typical channel.
Figure 22 shows a conceptual detail of how the ON-OFF keying scheme works.
8.2 Functional Block Diagram
Transmitter
TX IN
Receiver
OOK
Modulation
TX Signal
Conditioning
Oscillator
SiO2 based
Capacitive
Isolation
Barrier
RX Signal
Conditioning
Envelope
Detection
RX OUT
Emissions
Reduction
Techniques
Copyright © 2016, Texas Instruments Incorporated
Figure 21. Conceptual Block Diagram of a Digital Capacitive Isolator
TX IN
Carrier signal through
isolation barrier
RX OUT
Figure 22. ON-OFF Keying (OOK) Based Modulation Scheme
22
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: ISO7760 ISO7761 ISO7762 ISO7763
ISO7760, ISO7761
ISO7762, ISO7763
www.ti.com
SLLSER1C – AUGUST 2017 – REVISED JANUARY 2018
8.3 Feature Description
Table 1 lists the device features.
Table 1. Device Features
PART NUMBER
ISO7760
ISO7760 with F suffix
ISO7761
ISO7761 with F suffix
ISO7762
CHANNEL DIRECTION
MAXIMUM
DATA RATE
DEFAULT
OUTPUT
6 Forward,
0 Reverse
100 Mbps
High
6 Forward,
0 Reverse
5 Forward,
1 Reverse
5 Forward,
1 Reverse
4 Forward,
2 Reverse
ISO7762 with F suffix
4 Forward,
2 Reverse
ISO7763
3 Forward,
3 Reverse
ISO7763 with F suffix
3 Forward,
3 Reverse
(1)
100 Mbps
100 Mbps
100 Mbps
100 Mbps
100 Mbps
100 Mbps
100 Mbps
Low
High
Low
High
Low
High
Low
PACKAGE
RATED ISOLATION (1)
DW-16
5000 VRMS / 8000 VPK
DBQ-16
3000 VRMS / 4242 VPK
DW-16
5000 VRMS / 8000 VPK
DBQ-16
3000 VRMS / 4242 VPK
DW-16
5000 VRMS / 7071 VPK
DBQ-16
3000 VRMS / 4242 VPK
DW-16
5000 VRMS / 7071 VPK
DBQ-16
3000 VRMS / 4242 VPK
DW-16
5000 VRMS / 7071 VPK
DBQ-16
3000 VRMS / 4242 VPK
DW-16
5000 VRMS / 7071 VPK
DBQ-16
3000 VRMS / 4242 VPK
DW-16
5000 VRMS / 7071 VPK
DBQ-16
3000 VRMS / 4242 VPK
DW-16
5000 VRMS / 7071 VPK
DBQ-16
3000 VRMS / 4242 VPK
See Table 2 for detailed isolation ratings.
8.3.1 Electromagnetic Compatibility (EMC) Considerations
Many applications in harsh industrial environment are sensitive to disturbances such as electrostatic discharge
(ESD), electrical fast transient (EFT), surge and electromagnetic emissions. These electromagnetic disturbances
are regulated by international standards such as IEC 61000-4-x and CISPR 22. Although system-level
performance and reliability depends, to a large extent, on the application board design and layout, the ISO776x
family of devices incorporates many chip-level design improvements for overall system robustness. Some of
these improvements include:
• Robust ESD protection for input and output signal pins and inter-chip bond pads.
• Low-resistance connectivity of ESD cells to supply and ground pins.
• Enhanced performance of high voltage isolation capacitor for better tolerance of ESD, EFT and surge events.
• Bigger on-chip decoupling capacitors to bypass undesirable high energy signals through a low impedance
path.
• PMOS and NMOS devices isolated from each other by using guard rings to avoid triggering of parasitic
SCRs.
• Reduced common mode currents across the isolation barrier by ensuring purely differential internal operation.
Copyright © 2017–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: ISO7760 ISO7761 ISO7762 ISO7763
23
ISO7760, ISO7761
ISO7762, ISO7763
SLLSER1C – AUGUST 2017 – REVISED JANUARY 2018
www.ti.com
8.4 Device Functional Modes
Table 2 lists the functional modes for the ISO776x.
Table 2. Function Table (1)
VCCI
VCCO
PU
(1)
(2)
(3)
INPUT
(INx) (2)
OUTPUT
(OUTx)
H
H
L
L
Open
Default
Default mode: When INx is open, the corresponding channel output goes to its
default logic state. Default is High for ISO776x and Low for ISO776x with F
suffix.
Default mode: When VCCI is unpowered, a channel output assumes the logic
state based on the selected default option. Default is High for ISO776x and
Low for ISO776x with F suffix.
When VCCI transitions from unpowered to powered-up, a channel output
assumes the logic state of its input.
When VCCI transitions from powered-up to unpowered, channel output assumes
the selected default state.
COMMENTS
Normal Operation:
A channel output assumes the logic state of the input.
PU
PD
PU
X
Default
X
PD
X
Undetermined
When VCCO is unpowered, a channel output is undetermined (3).
When VCCO transitions from unpowered to powered-up, a channel output
assumes the logic state of the input
VCCI = Input-side VCC; VCCO = Output-side VCC; PU = Powered up (VCC ≥ 2.25 V); PD = Powered down (VCC ≤ 1.7 V); X = Irrelevant; H
= High level; L = Low level
A strongly driven input signal can weakly power the floating VCC via an internal protection diode and cause undetermined output.
The outputs are in undetermined state when 1.7 V < VCCI, VCCO < 2.25 V.
8.4.1 Device I/O Schematics
Input (Devices without F suffix)
VCCI
VCCI
VCCI
Input (Devices with F suffix)
VCCI
VCCI
VCCI
VCCI
1.5 M
985
985
INx
INx
1.5 M
Output
VCCO
~20
OUTx
Copyright © 2016, Texas Instruments Incorporated
Figure 23. Device I/O Schematics
24
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: ISO7760 ISO7761 ISO7762 ISO7763
ISO7760, ISO7761
ISO7762, ISO7763
www.ti.com
SLLSER1C – AUGUST 2017 – REVISED JANUARY 2018
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
The ISO776x family of devices is a high-performance, six-channel digital isolators. The ISO776x family of
devices uses single-ended CMOS-logic switching technology. The voltage range is from 2.25 V to 5.5 V for both
supplies, VCC1 and VCC2. When designing with digital isolators, keep in mind that because of the single-ended
design structure, digital isolators do not conform to any specific interface standard and are only intended for
isolating single-ended CMOS or TTL digital signal lines. The isolator is typically placed between the data
controller (that is, μC or UART), and a data converter or a line transceiver, regardless of the interface type or
standard.
9.2 Typical Application
Figure 24 shows the isolated serial-peripheral interface (SPI) and controller-area network (CAN) interface
implementation.
Copyright © 2017–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: ISO7760 ISO7761 ISO7762 ISO7763
25
ISO7760, ISO7761
ISO7762, ISO7763
SLLSER1C – AUGUST 2017 – REVISED JANUARY 2018
www.ti.com
Typical Application (continued)
VS
10 F
3.3 V
2
Vcc
MBR0520L
1:1.33
D2
3
1
10 F 0.1 F
D1
4
OUT
TPS76333
SN6501
GND
IN
1
3
EN
GND
5
ISO 3.3V
10 F
2
2
1 µF
22 µF
GND
0.1 µF
0.1 F
0.1 F
VCC1
2
SPISTEA
44
SPICLKA
SPISIMOA
SPISOMIA
TMS320F28035PAG
CANRXA
CANTXA
VSS
3
33
4
36
6
34
5
25
INA
OUTA
OUTB
INB
INC
ISO7762
OUTC
INE
OUTF
INF
IND
8
15
33
14
34
7
36
4
CS
CH0
SCLK
28
16 Analog
Inputs
ADS7953
SDI
SDO
13
CH15
27
AGND
11
REFM
1, 22
30
11
0.1 F
10
OUTD 12
GND2
5
AINP MXO +VBD +VA REFP
BDGND
OUTE
GND1
6, 28
31
32
7
26
8
16
VCC2
1
0.1 F
VDDIO
6
5
ISO Barrier
29, 57
VOUT
REF5025
4
MBR0520L
GND
VIN
3
4
9
1
VCC
R
D
RS 8
10
CANH
7
SN65HVD231
6 10
CANL
(optional)
CAN Bus
(optional)
Vref 5
GND
SM712
2
4.7 nF /
2 kV
NOTE: Multiple pins and discrete components omitted for clarity purpose.
Figure 24. Isolated SPI and CAN Interface
9.2.1 Design Requirements
For this design example, use the parameters listed in Table 3.
Table 3. Design Parameters
PARAMETER
VALUE
Supply voltage, VCC1 and VCC2
2.25 to 5.5 V
Decoupling capacitor between VCC1 and GND1
0.1 µF
Decoupling capacitor from VCC2 and GND2
0.1 µF
26
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: ISO7760 ISO7761 ISO7762 ISO7763
ISO7760, ISO7761
ISO7762, ISO7763
www.ti.com
SLLSER1C – AUGUST 2017 – REVISED JANUARY 2018
9.2.2 Detailed Design Procedure
Unlike optocouplers, which require external components to improve performance, provide bias, or limit current,
the ISO776x family of devices only requires two external bypass capacitors to operate.
0.1 µF
0.1 µF
VCC1
1
16
VCC2
INA
2
15
OUTA
INB
3
14
OUTB
INC
4
13
OUTC
IND
5
12
OUTD
INE
6
11
OUTE
OUTF
7
10
INF
8
9
GND2
GND1
Figure 25. Typical ISO7761 Circuit Hook-up
Copyright © 2017–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: ISO7760 ISO7761 ISO7762 ISO7763
27
ISO7760, ISO7761
ISO7762, ISO7763
SLLSER1C – AUGUST 2017 – REVISED JANUARY 2018
www.ti.com
9.2.3 Application Curves
The typical eye diagram of the ISO776x family of devices indicates low jitter and a wide open eye at the
maximum data rate of 100 Mbps.
Figure 26. Eye Diagram at 100 Mbps PRBS 216 – 1 Data,
5 V and 25°C
Figure 27. Eye Diagram at 100 Mbps PRBS 216 – 1 Data,
3.3 V and 25°C
Figure 28. Eye Diagram at 100 Mbps PRBS 216 – 1 Data,
2.5 V and 25°C
10 Power Supply Recommendations
To help ensure reliable operation at data rates and supply voltages, a 0.1-μF bypass capacitor is recommended
at input and output supply pins (VCC1 and VCC2). The capacitors should be placed as close to the supply pins as
possible. If only a single primary-side power supply is available in an application, isolated power can be
generated for the secondary-side with the help of a transformer driver such as Texas Instruments' SN6501 or
SN6505. For such applications, detailed power supply design and transformer selection recommendations are
available in the SN6501 Transformer Driver for Isolated Power Supplies data sheet or the SN6505 Low-Noise 1A Transformer Drivers for Isolated Power Supplies data sheet.
28
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: ISO7760 ISO7761 ISO7762 ISO7763
ISO7760, ISO7761
ISO7762, ISO7763
www.ti.com
SLLSER1C – AUGUST 2017 – REVISED JANUARY 2018
11 Layout
11.1 Layout Guidelines
A minimum of four layers is required to accomplish a low EMI PCB design (see Figure 29). Layer stacking should
be in the following order (top-to-bottom): high-speed signal layer, ground plane, power plane and low-frequency
signal layer.
• Routing the high-speed traces on the top layer avoids the use of vias (and the introduction of their
inductances) and allows for clean interconnects between the isolator and the transmitter and receiver circuits
of the data link.
• Placing a solid ground plane next to the high-speed signal layer establishes controlled impedance for
transmission line interconnects and provides an excellent low-inductance path for the return current flow.
• Placing the power plane next to the ground plane creates additional high-frequency bypass capacitance of
approximately 100 pF/inch2.
• Routing the slower speed control signals on the bottom layer allows for greater flexibility as these signal links
usually have margin to tolerate discontinuities such as vias.
If an additional supply voltage plane or signal layer is needed, add a second power or ground plane system to
the stack to keep it symmetrical. This makes the stack mechanically stable and prevents it from warping. Also the
power and ground plane of each power system can be placed closer together, thus increasing the high-frequency
bypass capacitance significantly.
For detailed layout recommendations, see the Digital Isolator Design Guide application report.
11.1.1 PCB Material
For digital circuit boards operating at less than 150 Mbps, (or rise and fall times greater than 1 ns), and trace
lengths of up to 10 inches, use standard FR-4 UL94V-0 printed circuit board. This PCB is preferred over cheaper
alternatives because of lower dielectric losses at high frequencies, less moisture absorption, greater strength and
stiffness, and the self-extinguishing flammability-characteristics.
11.2 Layout Example
High-speed traces
10 mils
Ground plane
40 mils
Keep this
space free
from planes,
traces, pads,
and vias
FR-4
0r ~ 4.5
Power plane
10 mils
Low-speed traces
Figure 29. Layout Example Schematic
Copyright © 2017–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: ISO7760 ISO7761 ISO7762 ISO7763
29
ISO7760, ISO7761
ISO7762, ISO7763
SLLSER1C – AUGUST 2017 – REVISED JANUARY 2018
www.ti.com
12 Device and Documentation Support
12.1 Documentation Support
12.1.1 Related Documentation
For related documentation see the following:
• Texas Instruments, ADS79xx 12/10/8-Bit, 1 MSPS, 16/12/8/4-Channel, Single-Ended, MicroPower, Serial
Interface ADCs data sheet
• Texas Instruments, Digital Isolator Design Guide application report
• Texas Instruments, Isolation Glossary
• Texas Instruments, REF50xx Low-Noise, Very Low Drift, Precision Voltage Reference data sheet
• Texas Instruments, SN6501 Transformer Driver for Isolated Power Supplies data sheet
• Texas Instruments, SN65HVD23x 3.3-V CAN Bus Transceivers data sheet
• Texas Instruments, TMS320F28035PAG Piccolo™ Microcontrollers data sheet
• Texas Instruments, TPS76333 Low-Power 150-mA Low-Dropout Linear Regulators data sheet
12.2 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 4. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
ISO7760
Click here
Click here
Click here
Click here
Click here
ISO7761
Click here
Click here
Click here
Click here
Click here
ISO7762
Click here
Click here
Click here
Click here
Click here
ISO7763
Click here
Click here
Click here
Click here
Click here
12.3 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
12.4 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
12.5 Trademarks
Piccolo, E2E are trademarks of Texas Instruments.
All other trademarks are the property of their respective owners.
12.6 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
30
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: ISO7760 ISO7761 ISO7762 ISO7763
ISO7760, ISO7761
ISO7762, ISO7763
www.ti.com
SLLSER1C – AUGUST 2017 – REVISED JANUARY 2018
12.7 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2017–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: ISO7760 ISO7761 ISO7762 ISO7763
31
ISO7760, ISO7761
ISO7762, ISO7763
SLLSER1C – AUGUST 2017 – REVISED JANUARY 2018
www.ti.com
PACKAGE OUTLINE
DW0016B
SOIC - 2.65 mm max height
SCALE 1.500
SOIC
C
10.63
TYP
9.97
SEATING PLANE
PIN 1 ID
AREA
A
0.1 C
14X 1.27
16
1
2X
8.89
10.5
10.1
NOTE 3
8
9
0.51
0.31
0.25
C A
16X
7.6
7.4
NOTE 4
B
2.65 MAX
B
0.33
TYP
0.10
SEE DETAIL A
0.25
GAGE PLANE
0.3
0.1
0 -8
1.27
0.40
DETAIL A
(1.4)
TYPICAL
4221009/B 07/2016
NOTES:
1. All linear dimensions are in millimeters. Dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed 0.15 mm, per side.
4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.25 mm, per side.
5. Reference JEDEC registration MS-013.
www.ti.com
32
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: ISO7760 ISO7761 ISO7762 ISO7763
ISO7760, ISO7761
ISO7762, ISO7763
www.ti.com
SLLSER1C – AUGUST 2017 – REVISED JANUARY 2018
EXAMPLE BOARD LAYOUT
DW0016B
SOIC - 2.65 mm max height
SOIC
SYMM
SYMM
16X (2)
16X (1.65)
SEE
DETAILS
1
SEE
DETAILS
1
16
16
16X (0.6)
16X (0.6)
SYMM
SYMM
14X (1.27)
14X (1.27)
9
8
9
8
R0.05 TYP
R0.05 TYP
(9.75)
(9.3)
HV / ISOLATION OPTION
8.1 mm CLEARANCE/CREEPAGE
IPC-7351 NOMINAL
7.3 mm CLEARANCE/CREEPAGE
LAND PATTERN EXAMPLE
SCALE:4X
SOLDER MASK
OPENING
METAL
SOLDER MASK
OPENING
0.07 MAX
ALL AROUND
METAL
0.07 MIN
ALL AROUND
SOLDER MASK
DEFINED
NON SOLDER MASK
DEFINED
SOLDER MASK DETAILS
4221009/B 07/2016
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
Copyright © 2017–2018, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: ISO7760 ISO7761 ISO7762 ISO7763
33
ISO7760, ISO7761
ISO7762, ISO7763
SLLSER1C – AUGUST 2017 – REVISED JANUARY 2018
www.ti.com
EXAMPLE STENCIL DESIGN
DW0016B
SOIC - 2.65 mm max height
SOIC
SYMM
SYMM
16X (1.65)
16X (2)
1
1
16
16
16X (0.6)
16X (0.6)
SYMM
SYMM
14X (1.27)
14X (1.27)
9
8
9
8
R0.05 TYP
R0.05 TYP
(9.3)
(9.75)
IPC-7351 NOMINAL
7.3 mm CLEARANCE/CREEPAGE
HV / ISOLATION OPTION
8.1 mm CLEARANCE/CREEPAGE
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
SCALE:4X
4221009/B 07/2016
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
www.ti.com
34
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: ISO7760 ISO7761 ISO7762 ISO7763
PACKAGE OPTION ADDENDUM
www.ti.com
29-Jan-2018
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
ISO7760DBQ
PREVIEW
SSOP
DBQ
16
75
TBD
Call TI
Call TI
-55 to 125
ISO7760DBQR
PREVIEW
SSOP
DBQ
16
2500
TBD
Call TI
Call TI
-55 to 125
ISO7760DW
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-55 to 125
ISO7760
ISO7760DWR
ACTIVE
SOIC
DW
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-55 to 125
ISO7760
ISO7760FDBQ
PREVIEW
SSOP
DBQ
16
75
TBD
Call TI
Call TI
-55 to 125
ISO7760FDBQR
PREVIEW
SSOP
DBQ
16
2500
TBD
Call TI
Call TI
-55 to 125
ISO7760FDW
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-55 to 125
ISO7760F
ISO7760FDWR
ACTIVE
SOIC
DW
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-55 to 125
ISO7760F
ISO7761DBQ
PREVIEW
SSOP
DBQ
16
75
TBD
Call TI
Call TI
-55 to 125
ISO7761DBQR
PREVIEW
SSOP
DBQ
16
2500
TBD
Call TI
Call TI
-55 to 125
ISO7761DW
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-55 to 125
ISO7761
ISO7761DWR
ACTIVE
SOIC
DW
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-55 to 125
ISO7761
ISO7761FDBQ
PREVIEW
SSOP
DBQ
16
75
TBD
Call TI
Call TI
-55 to 125
ISO7761FDBQR
PREVIEW
SSOP
DBQ
16
2500
TBD
Call TI
Call TI
-55 to 125
ISO7761FDW
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-55 to 125
ISO7761F
ISO7761FDWR
ACTIVE
SOIC
DW
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-55 to 125
ISO7761F
ISO7762DBQ
PREVIEW
SSOP
DBQ
16
75
TBD
Call TI
Call TI
-55 to 125
ISO7762DBQR
PREVIEW
SSOP
DBQ
16
2500
TBD
Call TI
Call TI
-55 to 125
ISO7762DW
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-55 to 125
ISO7762
ISO7762DWR
ACTIVE
SOIC
DW
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-55 to 125
ISO7762
ISO7762FDBQ
PREVIEW
SSOP
DBQ
16
75
TBD
Call TI
Call TI
-55 to 125
ISO7762FDBQR
PREVIEW
SSOP
DBQ
16
2500
TBD
Call TI
Call TI
-55 to 125
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
29-Jan-2018
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
ISO7762FDW
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-55 to 125
ISO7762F
ISO7762FDWR
ACTIVE
SOIC
DW
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-55 to 125
ISO7762F
ISO7763DBQ
PREVIEW
SSOP
DBQ
16
75
TBD
Call TI
Call TI
-55 to 125
ISO7763DBQR
PREVIEW
SSOP
DBQ
16
2500
TBD
Call TI
Call TI
-55 to 125
ISO7763DW
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-55 to 125
ISO7763
ISO7763DWR
ACTIVE
SOIC
DW
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-55 to 125
ISO7763
ISO7763FDBQ
PREVIEW
SSOP
DBQ
16
75
TBD
Call TI
Call TI
-55 to 125
ISO7763FDBQR
PREVIEW
SSOP
DBQ
16
2500
TBD
Call TI
Call TI
-55 to 125
ISO7763FDW
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-55 to 125
ISO7763F
ISO7763FDWR
ACTIVE
SOIC
DW
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-55 to 125
ISO7763F
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Addendum-Page 2
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
29-Jan-2018
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
16-Jan-2018
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
ISO7760DWR
SOIC
DW
16
2000
330.0
16.4
10.75
10.7
2.7
12.0
16.0
Q1
ISO7760FDWR
SOIC
DW
16
2000
330.0
16.4
10.75
10.7
2.7
12.0
16.0
Q1
ISO7761DWR
SOIC
DW
16
2000
330.0
16.4
10.75
10.7
2.7
12.0
16.0
Q1
ISO7761FDWR
SOIC
DW
16
2000
330.0
16.4
10.75
10.7
2.7
12.0
16.0
Q1
ISO7762DWR
SOIC
DW
16
2000
330.0
16.4
10.75
10.7
2.7
12.0
16.0
Q1
ISO7762FDWR
SOIC
DW
16
2000
330.0
16.4
10.75
10.7
2.7
12.0
16.0
Q1
ISO7763DWR
SOIC
DW
16
2000
330.0
16.4
10.75
10.7
2.7
12.0
16.0
Q1
ISO7763FDWR
SOIC
DW
16
2000
330.0
16.4
10.75
10.7
2.7
12.0
16.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
16-Jan-2018
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
ISO7760DWR
SOIC
DW
16
2000
367.0
367.0
38.0
ISO7760FDWR
SOIC
DW
16
2000
367.0
367.0
38.0
ISO7761DWR
SOIC
DW
16
2000
367.0
367.0
38.0
ISO7761FDWR
SOIC
DW
16
2000
367.0
367.0
38.0
ISO7762DWR
SOIC
DW
16
2000
367.0
367.0
38.0
ISO7762FDWR
SOIC
DW
16
2000
367.0
367.0
38.0
ISO7763DWR
SOIC
DW
16
2000
367.0
367.0
38.0
ISO7763FDWR
SOIC
DW
16
2000
367.0
367.0
38.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s noncompliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2018, Texas Instruments Incorporated