TI CD54HC4046A High-speed cmos logic phase-locked loop with vco Datasheet

[ /Title
(CD74
HC404
6A,
CD74
HCT40
46A)
/Subject
(HighSpeed
CMOS
CD54HC4046A, CD74HC4046A,
CD54HCT4046A, CD74HCT4046A
Data sheet acquired from Harris Semiconductor
SCHS204J
High-Speed CMOS Logic
Phase-Locked Loop with VCO
February 1998 - Revised December 2003
Features
Description
• Operating Frequency Range
- Up to 18MHz (Typ) at VCC = 5V
- Minimum Center Frequency of 12MHz at VCC = 4.5V
The ’HC4046A and ’HCT4046A are high-speed silicon-gate
CMOS devices that are pin compatible with the CD4046B of
the “4000B” series. They are specified in compliance with
JEDEC standard number 7.
• Choice of Three Phase Comparators
- EXCLUSIVE-OR
- Edge-Triggered JK Flip-Flop
- Edge-Triggered RS Flip-Flop
The ’HC4046A and ’HCT4046A are phase-locked-loop
circuits that contain a linear voltage-controlled oscillator
(VCO) and three different phase comparators (PC1, PC2 and
PC3). A signal input and a comparator input are common to
each comparator.
• Excellent VCO Frequency Linearity
The signal input can be directly coupled to large voltage
signals, or indirectly coupled (with a series capacitor) to small
voltage signals. A self-bias input circuit keeps small voltage
signals within the linear region of the input amplifiers. With a
passive low-pass filter, the 4046A forms a second-order loop
PLL. The excellent VCO linearity is achieved by the use of
linear op-amp techniques.
• VCO-Inhibit Control for ON/OFF Keying and for Low
Standby Power Consumption
• Minimal Frequency Drift
• Operating Power Supply Voltage Range
- VCO Section . . . . . . . . . . . . . . . . . . . . . . . . . . 3V to 6V
- Digital Section . . . . . . . . . . . . . . . . . . . . . . . . 2V to 6V
Ordering Information
• Fanout (Over Temperature Range)
- Standard Outputs . . . . . . . . . . . . . . . 10 LSTTL Loads
- Bus Driver Outputs . . . . . . . . . . . . . 15 LSTTL Loads
PART NUMBER
TEMP. RANGE
(oC)
PACKAGE
CD54HC4046AF3A
-55 to 125
16 Ld CERDIP
CD54HCT4046AF3A
-55 to 125
16 Ld CERDIP
• Balanced Propagation Delay and Transition Times
CD74HC4046AE
-55 to 125
16 Ld PDIP
• Significant Power Reduction Compared to LSTTL
Logic ICs
CD74HC4046AM
-55 to 125
16 Ld SOIC
CD74HC4046AMT
-55 to 125
16 Ld SOIC
• HC Types
- 2V to 6V Operation
- High Noise Immunity: NIL = 30%, NIH = 30% of VCC
at VCC = 5V
CD74HC4046AM96
-55 to 125
16 Ld SOIC
CD74HC4046ANSR
-55 to 125
16 Ld SOP
CD74HC4046APWR
-55 to 125
16 Ld TSSOP
CD74HC4046APWT
-55 to 125
16 Ld TSSOP
• HCT Types
- 4.5V to 5.5V Operation
- Direct LSTTL Input Logic Compatibility,
VIL= 0.8V (Max), VIH = 2V (Min)
- CMOS Input Compatibility, Il ≤ 1µA at VOL, VOH
CD74HCT4046AE
-55 to 125
16 Ld PDIP
• Wide Operating Temperature Range . . . -55oC to 125oC
CD74HCT4046AM
-55 to 125
16 Ld SOIC
CD74HCT4046AMT
-55 to 125
16 Ld SOIC
CD74HCT4046AM96
-55 to 125
16 Ld SOIC
NOTE: When ordering, use the entire part number. The suffixes 96
and R denote tape and reel. The suffix T denotes a small-quantity
reel of 250.
Applications
• FM Modulation and Demodulation
• Frequency Synthesis and Multiplication
• Frequency Discrimination
• Tone Decoding
• Data Synchronization and Conditioning
• Voltage-to-Frequency Conversion
• Motor-Speed Control
CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper IC Handling Procedures.
Copyright
© 2003, Texas Instruments Incorporated
1
CD54HC4046A, CD74HC4046A, CD54HCT4046A, CD74HCT4046A
Pinout
CD54HC4046A, CD54HCT4046A (CERDIP)
CD74HC4046A (PDIP, SOIC, SOP, TSSOP)
CD74HCT4046A (PDIP, SOIC)
TOP VIEW
PCPOUT 1
16 VCC
PC1OUT 2
15 PC3OUT
COMPIN 3
14 SIGIN
VCOOUT 4
13 PC2OUT
INH 5
12 R2
C1A 6
11 R1
C1B 7
10 DEMOUT
9 VCOIN
GND 8
Functional Diagram
2
PC1OUT
3
COMPIN
15
14
φ
SIGIN
PC3OUT
13
PC2OUT
1
PCPOUT
6
C1A
C1B
R1
R2
VCOIN
7
4
11
12
VCOOUT
VCO
10
9
DEMOUT
5
INH
Pin Descriptions
PIN NUMBER
SYMBOL
NAME AND FUNCTION
1
PCPOUT
Phase Comparator Pulse Output
2
PC1OUT
Phase Comparator 1 Output
3
COMPIN
Comparator Input
4
VCOOUT
VCO Output
5
INH
Inhibit Input
6
C1A
Capacitor C1 Connection A
7
C1B
Capacitor C1 Connection B
8
GND
Ground (0V)
9
VCOIN
10
DEMOUT
11
R1
Resistor R1 Connection
12
R2
Resistor R2 Connection
13
PC2OUT
14
SIGIN
15
PC3OUT
16
VCC
VCO Input
Demodulator Output
Phase Comparator 2 Output
Signal Input
Phase Comparator 3 Output
Positive Supply Voltage
2
CD54HC4046A, CD74HC4046A, CD54HCT4046A, CD74HCT4046A
C1
7 4
C1A
C1B
3
14
SIGIN
COMPIN
+
VREF
VCOOUT
6
12 R2
SD
-
R2
PC1OUT
2
PC3OUT
15
Q
VCO
Q
RD
11 R1
R1
+
VCC
VCC
-
D
10
R5
DEMOUT
-
Q
UP
p
CP Q
RD
+
13
PC2OUT
R3
C2
n
VCC
D
Q
CP
Q
RD
INH
VCOIN
5
9
GND
DOWN
1
PCPOUT
FIGURE 1. LOGIC DIAGRAM
General Description
VCO
Phase Comparators
The VCO requires one external capacitor C1 (between C1A
and C1B) and one external resistor R1 (between R1 and
GND) or two external resistors R1 and R2 (between R1 and
GND, and R2 and GND). Resistor R1 and capacitor C1
determine the frequency range of the VCO. Resistor R2
enables the VCO to have a frequency offset if required. See
logic diagram, Figure 1.
The signal input (SIGIN) can be directly coupled to the selfbiasing amplifier at pin 14, provided that the signal swing is
between the standard HC family input logic levels.
Capacitive coupling is required for signals with smaller
swings.
Phase Comparator 1 (PC1)
This is an Exclusive-OR network. The signal and comparator
input frequencies (fi) must have a 50% duty factor to obtain
the maximum locking range. The transfer characteristic of
PC1, assuming ripple (fr = 2fi) is suppressed, is:
The high input impedance of the VCO simplifies the design
of low-pass filters by giving the designer a wide choice of
resistor/capacitor ranges. In order not to load the low-pass
filter, a demodulator output of the VCO input voltage is
provided at pin 10 (DEMOUT). In contrast to conventional
techniques where the DEMOUT voltage is one threshold
voltage lower than the VCO input voltage, here the DEMOUT
voltage equals that of the VCO input. If DEMOUT is used, a
load resistor (RS) should be connected from DEMOUT to
GND; if unused, DEMOUT should be left open. The VCO
output (VCOOUT) can be connected directly to the
comparator input (COMPIN), or connected via a frequencydivider. The VCO output signal has a specified duty factor of
50%. A LOW level at the inhibit input (INH) enables the VCO
and demodulator, while a HIGH level turns both off to
minimize standby power consumption.
VDEMOUT = (VCC/π) (φSIGIN - φCOMPIN) where VDEMOUT
is the demodulator output at pin 10; VDEMOUT = VPC1OUT
(via low-pass filter).
The average output voltage from PC1, fed to the VCO input
via the low-pass filter and seen at the demodulator output at
pin 10 (VDEMOUT), is the resultant of the phase differences
of signals (SIGIN) and the comparator input (COMPIN) as
shown in Figure 2. The average of VDEM is equal to 1/2
VCC when there is no signal or noise at SIGIN, and with this
input the VCO oscillates at the center frequency (fo).
Typical waveforms for the PC1 loop locked at fo are shown
in Figure 3.
3
CD54HC4046A, CD74HC4046A, CD54HCT4046A, CD74HCT4046A
VDEMOUT = (VCC/4π) (φSIGIN - φCOMPIN) where
VDEMOUT is the demodulator output at pin 10;
VDEMOUT = VPC2OUT (via low-pass filter).
The frequency capture range (2fC) is defined as the
frequency range of input signals on which the PLL will lock if
it was initially out-of-lock. The frequency lock range (2fL) is
defined as the frequency range of input signals on which the
loop will stay locked if it was initially in lock. The capture
range is smaller or equal to the lock range.
The average output voltage from PC2, fed to the VCO via the
low-pass filter and seen at the demodulator output at pin 10
(VDEMOUT), is the resultant of the phase differences of
SIGIN and COMPIN as shown in Figure 4. Typical waveforms
for the PC2 loop locked at fo are shown in Figure 5.
With PC1, the capture range depends on the low-pass filter
characteristics and can be made as large as the lock range.
This configuration retains lock behavior even with very noisy
input signals. Typical of this type of phase comparator is that
it can lock to input frequencies close to the harmonics of the
VCO center frequency.
VCC
VDEMOUT (AV)
VCC
1/2 VCC
VDEMOUT (AV)
1/2 VCC
0
-360o
90o
φDEMOUT
φDEMOUT
360o
FIGURE 4. PHASE COMPARATOR 2: AVERAGE OUTPUT
VOLTAGE vs INPUT PHASE DIFFERENCE:
VDEMOUT = VPC2OUT
= (VCC/4π) (φSIGIN - φCOMPIN);
φDEMOUT = (φSIGIN - φCOMPIN)
0
0o
0o
180o
FIGURE 2. PHASE COMPARATOR 1: AVERAGE OUTPUT
VOLTAGE vs INPUT PHASE DIFFERENCE:
VDEMOUT = VPC1OUT = (VCC/π) (φSIGIN φCOMPIN); φDEMOUT = (φSIGIN - φCOMPIN)
SIGIN
COMPIN
VCOOUT
VCC
PC2OUT
SIGIN
GND
HIGH IMPEDANCE OFF - STATE
COMPIN
VCOIN
VCOOUT
PCPOUT
PC1OUT
FIGURE 5. TYPICAL WAVEFORMS FOR PLL USING PHASE
COMPARATOR 2, LOOP LOCKED AT fo
VCC
VCOIN
GND
Phase Comparator 2 (PC2)
When the frequencies of SIGIN and COMPIN are equal but
the phase of SIGIN leads that of COMPIN, the p-type output
driver at PC2OUT is held “ON” for a time corresponding to
the phase difference (φDEMOUT). When the phase of SIGIN
lags that of COMPIN, the n-type driver is held “ON”.
This is a positive edge-triggered phase and frequency
detector. When the PLL is using this comparator, the loop
is controlled by positive signal transitions and the duty
factors of SIGIN and COMPIN are not important. PC2
comprises two D-type flip-flops, control-gating and a threestate output stage. The circuit functions as an up-down
counter (Figure 1) where SIGIN causes an up-count and
COMPIN a down-count. The transfer function of PC2,
assuming ripple (fr = fi) is suppressed, is:
When the frequency of SIGIN is higher than that of
COMPIN, the p-type output driver is held “ON” for most of
the input signal cycle time, and for the remainder of the
cycle both n- and p-type drivers are “OFF” (three-state). If
the SIGIN frequency is lower than the COMPIN frequency,
then it is the n-type driver that is held “ON” for most of the
cycle. Subsequently, the voltage at the capacitor (C2) of
the low-pass filter connected to PC2OUT varies until the
signal and comparator inputs are equal in both phase and
FIGURE 3. TYPICAL WAVEFORMS FOR PLL USING PHASE
COMPARATOR 1, LOOP LOCKED AT fo
4
CD54HC4046A, CD74HC4046A, CD54HCT4046A, CD74HCT4046A
frequency. At this stable point the voltage on C2 remains
constant as the PC2 output is in three-state and the VCO
input at pin 9 is a high impedance. Also in this condition,
the signal at the phase comparator pulse output (PCPOUT)
is a HIGH level and so can be used for indicating a locked
condition.
VCC
VDEMOUT (AV)
Thus, for PC2, no phase difference exists between SIGIN
and COMPIN over the full frequency range of the VCO.
Moreover, the power dissipation due to the low-pass filter is
reduced because both p- and n-type drivers are “OFF” for
most of the signal input cycle. It should be noted that the
PLL lock range for this type of phase comparator is equal to
the capture range and is independent of the low-pass filter.
With no signal present at SIGIN, the VCO adjusts, via PC2,
to its lowest frequency.
1/2 VCC
0
0o
180o
φDEMOUT
360o
FIGURE 6. PHASE COMPARATOR 3: AVERAGE OUTPUT
VOLTAGE vs INPUT PHASE DIFFERENCE:
VDEMOUT = VPC3OUT
= (VCC/2π) (φSIGIN - φCOMPIN);
φDEMOUT = (φSIGIN - φCOMPIN)
Phase Comparator 3 (PC3)
This is a positive edge-triggered sequential phase
detector using an RS-type flip-flop. When the PLL is using
this comparator, the loop is controlled by positive signal
transitions and the duty factors of SIGIN and COMPIN are
not important. The transfer characteristic of PC3,
assuming ripple (fr = fi) is suppressed, is:
VDEMOUT = (VCC/2p) (fSIGIN - fCOMPIN) where
VDEMOUT is the demodulator output at pin 10; VDEMOUT
= VPC3OUT (via low-pass filter).
SIGIN
COMPIN
VCOOUT
The average output from PC3, fed to the VCO via the lowpass filter and seen at the demodulator at pin 10
(VDEMOUT), is the resultant of the phase differences of
SIGIN and COMPIN as shown in Figure 6. Typical
waveforms for the PC3 loop locked at fo are shown in
Figure 7.
PC3OUT
VCOIN
VCC
GND
The phase-to-output response characteristic of PC3
(Figure 6) differs from that of PC2 in that the phase angle
between SIGIN and COMPIN varies between 0o and 360o
and is 180o at the center frequency. Also PC3 gives a
greater voltage swing than PC2 for input phase differences
but as aconsequence the ripple content of the VCO input
signal is higher. With no signal present at SIGIN, the VCO
adjusts, via PC3, to its highest frequency.
FIGURE 7. TYPICAL WAVEFORMS FOR PLL USING PHASE
COMPARATOR 3, LOOP LOCKED AT fo
The only difference between the HC and HCT versions is the
input level specification of the INH input. This input disables
the VCO section. The comparator’s sections are identical, so
that there is no difference in the SIGIN (pin 14) or COMPIN
(pin 3) inputs between the HC and the HCT versions.
5
CD54HC4046A, CD74HC4046A, CD54HCT4046A, CD74HCT4046A
Absolute Maximum Ratings
Thermal Information
DC Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 7V
DC Input Diode Current, IIK
For VI < -0.5V or VI > VCC + 0.5V . . . . . . . . . . . . . . . . . . . . . .±20mA
DC Output Diode Current, IOK
For VO < -0.5V or VO > VCC + 0.5V . . . . . . . . . . . . . . . . . . . .±20mA
DC Drain Current, per Output, IO
For -0.5V < VO < VCC + 0.5V. . . . . . . . . . . . . . . . . . . . . . . . . .±25mA
DC Output Source or Sink Current per Output Pin, IO
For VO > -0.5V or VO < VCC + 0.5V . . . . . . . . . . . . . . . . . . . .±25mA
DC VCC or Ground Current, ICC . . . . . . . . . . . . . . . . . . . . . . . . .±50mA
Package Thermal Impedance, θJA (see Note 1):
E (PDIP) Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67oC/W
M (SOIC) Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73oC/W
NS (SOP) Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64oC/W
PW (TSSOP) Package. . . . . . . . . . . . . . . . . . . . . . . . . . 108oC/W
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150oC
Maximum Storage Temperature Range . . . . . . . . . .-65oC to 150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC
(SOIC - Lead Tips Only)
Operating Conditions
Temperature Range, TA . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC
Supply Voltage Range, VCC
HC Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2V to 6V
HCT Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.5V to 5.5V
DC Input or Output Voltage, VI, VO . . . . . . . . . . . . . . . . . 0V to VCC
Input Rise and Fall Time
2V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000ns (Max)
4.5V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500ns (Max)
6V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400ns (Max)
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1. The package thermal impedance is calculated in accordance with JESD 51-7.
DC Electrical Specifications
TEST
CONDITIONS
PARAMETER
25oC
-40oC TO 85oC -55oC TO 125oC
SYMBOL
VI (V)
IO (mA)
VCC
(V)
VIH
-
-
3
2.1
-
-
2.1
4.5
3.15
-
-
3.15
-
3.15
-
V
6
4.2
-
-
4.2
-
4.2
-
V
MIN
TYP
MAX
MIN
MAX
MIN
MAX
UNITS
-
2.1
-
V
HC TYPES
VCO SECTION
INH High Level Input
Voltage
INH Low Level Input
Voltage
VIL
VCOOUT High Level
Output Voltage
CMOS Loads
VOH
-
VIH or VIL
VCOOUT High Level
Output Voltage
TTL Loads
VCOOUT Low Level
Output Voltage
CMOS Loads
VOL
VIH or VIL
VCOOUT Low Level
Output Voltage
TTL Loads
C1A, C1B Low Level
Output Voltage
(Test Purposes Only)
VOL
VIL or VIH
-
3
-
-
0.9
-
0.9
-
0.9
V
4.5
-
-
1.35
-
1.35
-
1.35
V
6
-
-
1.8
-
1.8
-
1.8
V
-0.02
3
2.9
-
-
2.9
-
2.9
-
V
-0.02
4.5
4.4
-
-
4.4
-
4.4
-
V
-0.02
6
5.9
-
-
5.9
-
5.9
-
V
-
-
-
-
-
-
-
-
-
V
-4
4.5
3.98
-
-
3.84
-
3.7
-
V
-5.2
6
5.48
-
-
5.34
-
5.2
-
V
0.02
2
-
-
0.1
-
0.1
-
0.1
V
0.02
4.5
-
-
0.1
-
0.1
-
0.1
V
0.02
6
-
-
0.1
-
0.1
-
0.1
V
-
-
-
-
-
-
-
-
-
V
4
4.5
-
-
0.26
-
0.33
-
0.4
V
5.2
6
-
-
0.26
-
0.33
-
0.4
V
4
4.5
-
-
0.40
-
0.47
-
0.54
V
5.2
6
-
-
0.40
-
0.47
-
0.54
V
6
CD54HC4046A, CD74HC4046A, CD54HCT4046A, CD74HCT4046A
DC Electrical Specifications
(Continued)
TEST
CONDITIONS
25oC
-40oC TO 85oC -55oC TO 125oC
SYMBOL
VI (V)
IO (mA)
VCC
(V)
INH VCOIN Input
Leakage Current
II
VCC or
GND
-
6
-
-
±0.1
-
±1
-
±1
µA
R1 Range (Note 2)
-
-
-
4.5
3
-
300
-
-
-
-
kΩ
R2 Range (Note 2)
-
-
-
4.5
3
-
300
-
-
-
-
kΩ
C1 Capacitance
Range
-
-
-
3
-
-
-
-
-
pF
-
-
No
Limit
-
4.5
-
-
-
-
pF
VCOIN Operating
Voltage Range
-
PARAMETER
MIN
TYP
MAX
MIN
MAX
MIN
MAX
UNITS
6
-
-
-
-
-
-
pF
3
1.1
-
1.9
-
-
-
-
V
4.5
1.1
-
3.2
-
-
-
-
V
6
1.1
-
4.6
-
-
-
-
V
2
1.5
-
-
1.5
-
1.5
-
V
4.5
3.15
-
-
3.15
-
3.15
-
V
6
4.2
-
-
4.2
-
4.2
-
V
2
-
-
0.5
-
0.5
-
0.5
V
4.5
-
-
1.35
-
1.35
-
1.35
V
6
-
-
1.8
-
1.8
-
1.8
V
2
1.9
-
-
1.9
-
1.9
-
V
4.5
4.4
-
-
4.4
-
4.4
-
V
6
5.9
-
-
5.9
-
5.9
-
V
-4
4.5
3.98
-
-
3.84
-
3.7
-
V
-5.2
6
5.48
-
-
5.34
-
5.2
-
V
0.02
2
-
-
0.1
-
0.1
-
0.1
V
4.5
-
-
0.1
-
0.1
-
0.1
V
6
-
-
0.1
-
0.1
-
0.1
V
4
4.5
-
-
0.26
-
0.33
-
0.4
V
5.2
6
-
-
0.26
-
0.33
-
0.4
V
-
2
-
-
±3
-
±4
-
±5
µA
Over the range
specified for R1 for
Linearity See Figure
10, and 34 - 37
(Note 3)
PHASE COMPARATOR SECTION
SIGIN, COMPIN
DC Coupled
High-Level Input
Voltage
VIH
SIGIN, COMPIN
DC Coupled
Low-Level Input
Voltage
VIL
PCPOUT, PCn OUT
High-Level Output
Voltage
CMOS Loads
VOH
PCPOUT, PCn OUT
High-Level Output
Voltage
TTL Loads
VOH
PCPOUT, PCn OUT
Low-Level Output
Voltage
CMOS Loads
VOL
PCPOUT, PCn OUT
Low-Level Output
Voltage
TTL Loads
VOL
SIGIN, COMPIN Input
Leakage Current
II
PC2OUT Three-State
Off-State Current
IOZ
SIGIN, COMPIN Input
Resistance
RI
-
-
VIL or VIH
VIL or VIH
VIL or VIH
VIL or VIH
VCC or
GND
VIL or VIH
-
-
-0.02
-
3
-
-
±7
-
±9
-
±11
µA
4.5
-
-
±18
-
±23
-
±29
µA
6
-
-
±30
-
±38
-
±45
µA
6
-
-
±0.5
-
±5
-
±10
µA
VI at Self-Bias
Operation Point:
∆VI = 0.5V,
See Figure 10
3
-
800
-
-
-
-
-
kΩ
4.5
-
250
-
-
-
-
-
kΩ
6
-
150
-
-
-
-
-
kΩ
at RS > 300kΩ
Leakage Current
Can Influence
VDEMOUT
3
50
-
300
-
-
-
-
kΩ
4.5
50
-
300
-
-
-
-
kΩ
6
50
-
300
-
-
-
-
kΩ
DEMODULATOR SECTION
Resistor Range
RS
7
CD54HC4046A, CD74HC4046A, CD54HCT4046A, CD74HCT4046A
DC Electrical Specifications
(Continued)
TEST
CONDITIONS
PARAMETER
SYMBOL
Offset Voltage VCOIN
to VDEM
VOFF
Dynamic Output
Resistance at
DEMOUT
RD
Quiescent Device
Current
ICC
VI (V)
IO (mA)
VI = VVCO IN =
VCC
2
Values Taken Over
RS Range
See Figure 23
VDEMOUT =
VCC
2
Pins 3, 5 and 14
at VCC Pin 9 at
GND, I1 at Pins 3
and 14 to be
excluded
VCC
(V)
25oC
-40oC TO 85oC -55oC TO 125oC
MIN
TYP
MAX
MIN
MAX
MIN
MAX
UNITS
3
-
±30
-
-
-
-
-
mV
4.5
-
±20
-
-
-
-
-
mV
6
-
±10
-
-
-
-
-
mV
3
-
25
-
-
-
-
-
Ω
4.5
-
25
-
-
-
-
-
Ω
6
-
25
-
-
-
-
-
Ω
6
-
-
8
-
80
-
160
µA
HCT TYPES
VCO SECTION
INH High Level Input
Voltage
VIH
-
-
4.5 to
5.5
2
-
-
2
-
2
-
V
INH Low Level Input
Voltage
VIL
-
-
4.5 to
5.5
-
-
0.8
-
0.8
-
0.8
V
VCOOUT High Level
Output Voltage
CMOS Loads
VOH
VIH or VIL
-0.02
4.5
4.4
-
-
4.4
-
4.4
-
V
-4
4.5
3.98
-
-
3.84
-
3.7
-
V
0.02
4.5
-
-
0.1
-
0.1
-
0.1
V
4
4.5
-
-
0.26
-
0.33
-
0.4
V
4
4.5
-
-
0.40
-
0.47
-
0.54
V
5.5
-
±0.1
-
±1
-
±1
µA
VCOOUT High Level
Output Voltage
TTL Loads
VCOOUT Low Level
Output Voltage
CMOS Loads
VOL
VIH or VIL
VCOOUT Low Level
Output Voltage
TTL Loads
C1A, C1B Low Level
Output Voltage
(Test Purposes Only)
VOL
VIH or VIL
INH VCOIN Input
Leakage Current
II
Any Voltage
Between VCC and
GND
R1 Range (Note 2)
-
-
-
4.5
3
-
300
-
-
-
-
kΩ
R2 Range (Note 2)
-
-
-
4.5
3
-
300
-
-
-
-
kΩ
C1 Capacitance
Range
-
-
-
4.5
0
-
No
Limit
-
-
-
-
pF
VCOIN Operating
Voltage Range
-
4.5
1.1
-
3.2
-
-
-
-
V
4.5 to
5.5
2
-
-
2
-
2
-
V
Over the range
specified for R1 for
Linearity See Figure
10, and 34 - 37
(Note 3)
PHASE COMPARATOR SECTION
SIGIN, COMPIN
DC Coupled
High-Level Input
Voltage
VIH
-
-
8
CD54HC4046A, CD74HC4046A, CD54HCT4046A, CD74HCT4046A
DC Electrical Specifications
(Continued)
TEST
CONDITIONS
PARAMETER
SYMBOL
VI (V)
IO (mA)
SIGIN, COMPIN
DC Coupled
Low-Level Input
Voltage
VIL
-
-
PCPOUT, PCn OUT
High-Level Output
Voltage
CMOS Loads
VOH
VIL or VIH
PCPOUT, PCn OUT
High-Level Output
Voltage
TTL Loads
VOH
PCPOUT, PCn OUT
Low-Level Output
Voltage
CMOS Loads
PCPOUT, PCn OUT
Low-Level Output
Voltage
TTL Loads
VCC
(V)
25oC
-40oC TO 85oC -55oC TO 125oC
MIN
TYP
MAX
MIN
MAX
MIN
MAX
UNITS
4.5 to
5.5
-
-
0.8
-
0.8
-
0.8
V
-
4.5
4.4
-
-
4.4
-
4.4
-
V
VIL or VIH
-
4.5
3.98
-
-
3.84
-
3.7
-
V
VOL
VIL or VIH
-
4.5
-
-
0.1
-
0.1
-
0.1
V
VOL
VIL or VIH
-
4.5
-
-
0.26
-
0.33
-
0.4
V
SIGIN, COMPIN Input
Leakage Current
II
Any
Voltage
Between
VCC and
GND
-
5.5
-
-
±30
±45
µA
PC2OUT Three-State
Off-State Current
IOZ
VIL or VIH
-
5.5
-
-
±0.5
±5
-
-
±10
µA
SIGIN, COMPIN Input
Resistance
RI
VI at Self-Bias
Operation Point:
∆VI = 0.5V,
See Figure 10
4.5
-
250
-
-
-
-
-
kΩ
at RS > 300kΩ
Leakage Current
Can Influence
VDEM OUT
4.5
5
-
300
-
-
-
-
kΩ
VI = VVCO IN =
VCC
2
Values taken over
RS Range
See Figure 23
4.5
-
±20
-
-
-
-
-
mV
VDEM OUT =
VCC
2
4.5
-
25
-
-
-
-
-
Ω
±38
DEMODULATOR SECTION
Resistor Range
Offset Voltage VCOIN
to VDEM
RS
VOFF
Dynamic Output
Resistance at
DEMOUT
RD
Quiescent Device
Current
ICC
VCC or
GND
-
5.5
-
-
8
-
80
-
160
µA
∆ICC
(Note 4)
VCC
-2.1
Excluding
Pin 5
-
4.5 to
5.5
-
100
360
-
450
-
490
µA
Additional Quiescent
Device Current Per
Input Pin: 1 Unit Load
NOTES:
2. The value for R1 and R2 in parallel should exceed 2.7kΩ.
3. The maximum operating voltage can be as high as VCC -0.9V, however, this may result in an increased offset voltage.
4. For dual-supply systems theoretical worst case (VI = 2.4V, VCC = 5.5V) specification is 1.8mA.
9
CD54HC4046A, CD74HC4046A, CD54HCT4046A, CD74HCT4046A
HCT Input Loading Table
INPUT
UNIT LOADS
INH
1
NOTE: Unit load is ∆ICC limit specific in DC Electrical Specifications
Table, e.g., 360µA max. at 25oC.
Switching Specifications
PARAMETER
CL = 50pF, Input tr, tf = 6ns
SYMBOL
TEST
CONDITIONS
-40oC TO
85oC
25oC
-55oC TO
125oC
VCC (V)
MIN
TYP
MAX
MIN
MAX
MIN
MAX
UNITS
2
-
-
200
-
250
-
300
ns
4.5
-
-
40
-
50
-
60
ns
6
-
-
34
-
43
-
51
ns
2
-
-
300
-
375
-
450
ns
4.5
-
-
60
-
75
-
90
ns
6
-
-
51
-
64
-
77
ns
2
-
-
245
-
305
-
307
ns
4.5
-
-
49
-
61
-
74
ns
6
-
-
42
-
52
-
63
ns
2
-
-
75
-
95
-
110
ns
4.5
-
-
15
-
19
-
22
ns
6
-
-
13
-
16
-
19
ns
2
-
-
265
-
330
-
400
ns
4.5
-
-
53
-
66
-
80
ns
6
-
-
45
-
56
-
68
ns
2
-
-
315
-
395
-
475
ns
4.5
-
-
63
-
79
-
95
ns
6
-
-
54
-
67
-
81
ns
HC TYPES
PHASE COMPARATOR SECTION
Propagation Delay
SIGIN, COMPIN to PCIOUT
tPLH, tPHL
SIGIN, COMPIN to PCPOUT
SIGIN, COMPIN to PC3OUT
Output Transition Time
Output Enable Time, SIGIN,
COMPIN to PC2OUT
Output Disable Time, SIGIN,
COMPIN to PC2OUT
tTHL, tTLH
tPZH, tPZL
tPHZ, tPLZ
AC Coupled Input Sensitivity
(P-P) at SIGIN or COMPIN
VI(P-P)
3
-
11
-
-
-
-
-
mV
4.5
-
15
-
-
-
-
-
mV
6
-
33
-
-
-
-
-
mV
3
-
0.11
-
-
-
-
-
%/oC
4.5
-
0.11
-
-
-
-
-
%/oC
6
-
0.11
-
-
-
-
-
%/oC
3
-
24
-
-
-
-
-
MHz
4.5
-
24
-
-
-
-
-
MHz
6
-
24
-
-
-
-
-
MHz
3
-
38
-
-
-
-
-
MHz
4.5
-
38
-
-
-
-
-
MHz
6
-
38
-
-
-
-
-
MHz
VCO SECTION
Frequency Stability with
Temperature Change
Maximum Frequency
∆f
∆T
fMAX
R1 = 100kΩ,
R2 = ∞
C1 = 50pF
R1 = 3.5kΩ
R2 = ∞
C1 = 0pF
R1 = 9.1kΩ
R2 = ∞
10
CD54HC4046A, CD74HC4046A, CD54HCT4046A, CD74HCT4046A
Switching Specifications
PARAMETER
CL = 50pF, Input tr, tf = 6ns (Continued)
SYMBOL
Center Frequency
Frequency Linearity
TEST
CONDITIONS
C1 = 40pF
R1 = 3kΩ
R2 = ∞
VCOIN =
VCC/2
∆fVCO
Offset Frequency
R1 = 100kΩ
R2 = ∞
C1 = 100pF
R2 = 220kΩ
C1 = 1nF
-40oC TO
85oC
25oC
VCC (V)
MIN
TYP
MAX
MIN
MAX
-55oC TO
125oC
MIN
MAX
UNITS
3
7
10
-
-
-
-
-
MHz
4.5
12
17
-
-
-
-
-
MHz
6
14
21
-
-
-
-
-
MHz
3
-
0.4
-
-
-
-
-
%
4.5
-
0.4
-
-
-
-
-
%
6
-
0.4
-
-
-
-
-
%
3
-
400
-
-
-
-
-
kHz
4.5
-
400
-
-
-
-
-
kHz
6
-
400
-
-
-
-
-
kHz
DEMODULATOR SECTION
VOUT VS fIN
R1 = 100kΩ
R2 = ∞
C1 = 100pF
RS = 10kΩ
R3 = 100kΩ
C2 = 100pF
3
-
-
-
-
-
-
-
mV/kHz
4.5
-
330
-
-
-
-
-
mV/kHz
6
-
-
-
-
-
-
-
mV/kHz
CL = 50pF
4.5
-
-
45
-
56
-
68
ns
SIGIN, COMPIN to PCPOUT tPHL, tPLH
CL = 50pF
4.5
-
-
68
-
85
-
102
ns
SIGIN, COMPIN to PC3OUT tPHL, tPLH
CL = 50pF
4.5
-
-
58
-
73
-
87
ns
HCT TYPES
PHASE COMPARATOR SECTION
Propagation Delay
SIGIN, COMPIN to PCIOUT
tPHL, tPLH
Output Transition Time
tTLH, tTHL
CL = 50pF
4.5
-
-
15
-
19
-
22
ns
Output Enable Time, SIGIN,
COMPIN to PC2OUT
tPZH, tPZL
CL = 50pF
4.5
-
-
60
-
75
-
90
pF
Output Disable Time, SIGIN,
COMPIN to PCZOUT
tPHZ, tPLZ
CL = 50pF
4.5
-
-
68
-
85
-
102
pF
VI(P-P)
4.5
-
15
-
-
-
-
-
mV
∆f
∆T
R1 = 100kΩ,
R2 = ∞
4.5
-
0.11
-
-
-
-
-
%/oC
fMAX
C1 = 50pF
R1 = 3.5kΩ
R2 = ∞
4.5
-
24
-
-
-
-
-
MHz
C1 = 0pF
R1 = 9.1kΩ
R2 = ∞
4.5
-
38
-
-
-
-
-
MHz
C1 = 40pF
R1 = 3kΩ
R2 = ∞
VCOIN =
VCC/2
4.5
12
17
-
-
-
-
-
MHz
R1 = 100kΩ
R2 = ∞
C1 = 100pF
4.5
-
0.4
-
-
-
-
-
%
AC Coupled Input Sensitivity
(P-P) at SIGIN or COMPI
VCO SECTION
Frequency Stability with
Temperature Change
Maximum Frequency
Center Frequency
Frequency Linearity
∆fVCO
11
CD54HC4046A, CD74HC4046A, CD54HCT4046A, CD74HCT4046A
Switching Specifications
PARAMETER
CL = 50pF, Input tr, tf = 6ns (Continued)
SYMBOL
Offset Frequency
TEST
CONDITIONS
-40oC TO
85oC
25oC
-55oC TO
125oC
VCC (V)
MIN
TYP
MAX
MIN
MAX
MIN
MAX
UNITS
R2 = 220kΩ
C1 = 1nF
4.5
-
400
-
-
-
-
-
kHz
R1 = 100kΩ
R2 = ∞
C1 = 100pF
RS = 10kΩ
R3 = 100kΩ
C2 = 100pF
4.5
-
330
-
-
-
-
-
mV/kHz
DEMODULATOR SECTION
VOUT VS fIN
Test Circuits and Waveforms
SIGIN
INPUTS
SIGIN COMPIN
VS
VS
INPUTS
tPHL
tPHL
COMPIN
INPUTS
PCPOUT PC1OUT
tPZL
tPZH
VS
PC3OUT OUTPUTS
VS
tPZH
tTLH
PC2OUT
OUTPUT
tTLH
FIGURE 8. INPUT TO OUTPUT PROPAGATION DELAYS AND
OUTPUT TRANSITION TIMES
tPZL
90%
VS
10%
FIGURE 9. THREE STATE ENABLE AND DISABLE TIMES FOR
PC2OUT
Typical Performance Curves
II
∆VI
SELF-BIAS OPERATING POINT
VI
FIGURE 10. TYPICAL INPUT RESISTANCE CURVE AT SIGIN,
COMPIN
12
CD54HC4046A, CD74HC4046A, CD54HCT4046A, CD74HCT4046A
Typical Performance Curves
(Continued)
108
106
105
104
103
102
VCOIN = 0.5 VCC
10
1
106
105
104
103
102
VCOIN = 0.5 VCC
10
VCC = 6.0V
VCC = 4.5V
1
R1 =3K
R1 = 30K
R1 =330K
R1 = 3M
R1 = 15M
107
CENTER FREQUENCY (Hz)
107
CENTER FREQUENCY (Hz)
108
R1 = 2.2K
R1 = 22K
R1 = 220K
R1 = 2.2M
R1 = 11M
1
102
10
103
104
105
106
1
102
10
FIGURE 11. HC4046A TYPICAL CENTER FREQUENCY vs R1,
C1 (VCC = 4.5V)
108
105
104
103
102
VCOIN = 0.5 VCC
VCC = 3.0V
10
106
105
104
103
102
VCOIN = 0.5 VCC
10
VCC = 4.5V
R2 = OPEN
1
1
1
102
10
103
104
105
106
1
102
10
CAPACITANCE, C1 (pF)
108
103
104
105
106
CAPACITANCE, C1 (pF)
FIGURE 13. HC4046A TYPICAL CENTER FREQUENCY vs R1,
C1 (VCC = 3V, R2 = OPEN)
FIGURE 14. HCT4046A TYPICAL CENTER FREQUENCY vs R1,
C1 (VCC = 4.5V)
140
R1 = 3K
R1 = 30K
R1 = 300K
R1 = 3M
R1 = 15M
107
106
105
104
103
102
VCC = 5.5V
10
100
VCC = 4.5V
80
VCC = 3V
60
20
1
1
VCC = 6V
40
VCOIN = 0.5 VCC
10
C1 = 50pF
R1 = 1.5M
120
VCO FREQUENCY (kHz)
CENTER FREQUENCY (Hz)
106
R1 = 2.2K
R1 = 22K
R1 = 220K
R1 = 2.2M
R1 = 11M
107
CENTER FREQUENCY (Hz)
CENTER FREQUENCY (Hz)
106
105
FIGURE 12. HC4046A TYPICAL CENTER FREQUENCY vs R1,
C1 (VCC = 6V)
R1 = 1.5K
R1 = 15K
R1 = 150K
R1 = 1.5M
R1 = 7.5M
107
104
CAPACITANCE, C1 (pF)
CAPACITANCE, C1 (pF)
108
103
102
103
104
105
0
106
1
2
3
4
5
6
VCOIN (V)
CAPACITANCE, C1 (pF)
FIGURE 16. HC4046A TYPICAL VCO FREQUENCY vs VCOIN
(R1 = 1.5MΩ, C1 = 50pF)
FIGURE 15. HCT4046A TYPICAL CENTER FREQUENCY vs R1,
C1 (VCC = 5.5V)
13
CD54HC4046A, CD74HC4046A, CD54HCT4046A, CD74HCT4046A
Typical Performance Curves
(Continued)
90
800
C1 = 0.1µF
R1 = 1.5M
C1 = 0.1µF
R1 = 150K
70
VCC = 4.5V
60
50
VCC = 3V
40
VCC = 6V
700
VCO FREQUENCY (Hz)
VCO FREQUENCY (Hz)
80
VCC = 6V
30
600
VCC = 4.5V
500
400
VCC = 3V
300
200
20
10
100
0
1
2
3
4
5
6
0
1
2
VCOIN (V)
5
6
FIGURE 18. HC4046A TYPICAL VCO FREQUENCY vs VCOIN
(R1 = 150kΩ, C1 = 0.1µF)
18
1400
VCC = 6V
C1 = 0.1µF
R1 = 5.6k
VCC = 4.5V
14
VCC = 3V
12
10
8
6
VCC = 6V
C1 = 50pF
R1 = 150K
1200
VCO FREQUENCY (kHz)
16
VCO FREQUENCY (kHz)
4
VCOIN (V)
FIGURE 17. HC4046A TYPICAL VCO FREQUENCY vs VCOIN
(R1 = 1.5MΩ, C1 = 0.1µF)
1000
VCC = 4.5V
800
VCC = 3V
600
400
4
200
2
0
1
2
3
4
5
0
6
1
2
VCOIN (V)
3
4
5
6
VCOIN (V)
FIGURE 19. HC4046A TYPICAL VCO FREQUENCY vs VCOIN
(R1 = 5.6kΩ, C1 = 0.1µF)
FIGURE 20. HC4046A TYPICAL VCO FREQUENCY vs VCOIN
(R1 = 150kΩ, C1 = 50pF)
24
24
VCC = 6V
C1 = 50pF
R1 = 5.6K
20
VCO FREQUENCY CHANGE, ∆f (%)
VCO FREQUENCY (MHz)
3
VCC = 4.5V
16
12
VCC = 3V
8
4
0
1
2
3
4
5
20
16
R1 = 1.5M
12
R1 = 150K
8
4
0
R1 = 3K
-4
-8
R1 = 1.5K
-12
-16
-75
6
VCOIN = 0.5 VCC
C1 = 50pF, VCC = 3V
R2 = OPEN
-50
-25
0
25
50
75
100
125
150
AMBIENT TEMPERATURE, TA (oC)
VCOIN (V)
FIGURE 21. HC4046A TYPICAL VCO FREQUENCY vs VCOIN
(R1 = 5.6kΩ, C1 = 50pF)
FIGURE 22. HC4046A TYPICAL CHANGE IN VCO FREQUENCY
vs AMBIENT TEMPERATURE AS A FUNCTION OF
R1 (VCC = 3V)
14
CD54HC4046A, CD74HC4046A, CD54HCT4046A, CD74HCT4046A
Typical Performance Curves
VCOIN = 0.5 VCC
C1 = 50pF, VCC = 4.5V
R2 = OPEN
16
16
R1 = 2.2M
VCO FREQUENCY CHANGE, ∆f (%)
VCO FREQUENCY CHANGE, ∆f (%)
20
(Continued)
12
R1 = 220K
8
4
0
-4
R1 = 2.2K
-8
-12
-75
12
VCOIN = 0.5 VCC
C1 = 50pF, VCC = 6.0V
R2 = OPEN
8
R1 = 300K
4
0
-4
R1 = 3K
-8
-12
-50
-25
0
25
50
75
100
125
150
-75
-50
AMBIENT TEMPERATURE, TA (oC)
VCO FREQUENCY CHANGE, ∆f (%)
VCO FREQUENCY CHANGE, ∆f (%)
20
R1 = 3M
12
8
R1 = 300K
4
0
R1 = 3K
-4
-8
-12
-75
-50
-25
0
25
50
75
100
0
25
50
75
100
125
150
FIGURE 24. HC4046A TYPICAL CHANGE IN VCO FREQUENCY
vs AMBIENT TEMPERATURE AS A FUNCTION OF
R1 (VCC = 6V)
20
VCOIN = 0.5 VCC
C1 = 50pF, VCC = 5.5V
R2 = OPEN
-25
AMBIENT TEMPERATURE, TA (oC)
FIGURE 23. HC4046A TYPICAL CHANGE IN VCO FREQUENCY
vs AMBIENT TEMPERATURE AS A FUNCTION OF
R1 (VCC = 4.5V)
16
R1 = 3M
125
16
AMBIENT TEMPERATURE, TA (oC)
R1 = 2.2M
12
R1 = 220K
8
4
0
-4
R1 = 2.2K
-8
-12
-75
150
VCOIN = 0.5 VCC
C1 = 50pF, VCC = 4.5V
R2 = OPEN
-50
-25
0
25
50
75
100
125
150
AMBIENT TEMPERATURE, TA (oC)
FIGURE 25. HCT4046A TYPICAL CHANGE IN VCO
FREQUENCY vs AMBIENT TEMPERATURE AS A
FUNCTION OF R1
FIGURE 26. HC4046A TYPICAL CHANGE IN VCO FREQUENCY
vs AMBIENT TEMPERATURE AS A FUNCTION OF
R1 (VCC = 4.5V)
15
CD54HC4046A, CD74HC4046A, CD54HCT4046A, CD74HCT4046A
(Continued)
108
108
107
107
106
OFFSET FREQUENCY (Hz)
OFFSET FREQUENCY (Hz)
Typical Performance Curves
R2 = 2.2K
105
R2 = 22K
104
103
R2 = 220K
102
R2 = 2.2M
VCOIN = 0.5 VCC
VCC = 4.5V
10
1
1
102
10
106
R2 = 1.5K
105
104
R2 = 15K
103
R2 = 150K
102
R2 = 1.5M
VCOIN = 0.5 VCC
VCC = 3V
10
R2 = 11M
1
103
104
105
106
1
102
10
CAPACITANCE, C1 (pF)
107
107
OFFSET FREQUENCY (Hz)
OFFSET FREQUENCY (Hz)
108
106
R2 = 2.2K
105
104
R2 = 22K
103
R2 = 220K
102
R2 = 2.2M
VCOIN = 0.5 VCC
VCC = 4.5V
1
102
10
R2 = 30K
104
R2 = 300K
103
R2 = 3M
102
VCOIN = 0.5 VCC
HC VCC = 6V
HCT VCC = 5.5V
103
104
105
106
1
102
10
104
105
106
FIGURE 30. HC4046A AND HCT4046A OFFSET FREQUENCY
vs R2, C1 (VCC = 6V, VCC = 5.5V)
102
10
1
R2/R1
103
CAPACITANCE, C1 (pF)
fMAX /fMIN
fMAX /fMIN
R2 = 15M
1
PIN 9 = 0.95 VCC FOR fMAX
PIN 9 = 0V FOR fMIN
VCC = 3V, 4.5V, 6V
10-1
106
R2 = 3K
105
10
R2 = 11M
FIGURE 29. HCT4046A OFFSET FREQUENCY vs R2, C1
(VCC = 4.5V)
0
10-2
105
106
CAPACITANCE, C1 (pF)
102
104
FIGURE 28. HC4046A OFFSET FREQUENCY vs R2, C1
(VCC = 3V)
108
1
103
CAPACITANCE, C1 (pF)
FIGURE 27. HC4046A OFFSET FREQUENCY vs R2, C1
(VCC = 4.5V)
10
R2 = 7.5M
10
PIN 9 = 0.95 VCC FOR fMAX
PIN 9 = 0V FOR fMIN
VCC = 4.5V TO 5.5V
10
0
10-2
102
FIGURE 31. HC4046A fMIN/fMAX vs R2/R1 (VCC = 3V, 4.5V, 6V)
10-1
1
R2/R1
10
102
FIGURE 32. HCT4046A fMAX/fMIN vs R2/R1 (VCC = 4.5V TO 5.5V)
16
CD54HC4046A, CD74HC4046A, CD54HCT4046A, CD74HCT4046A
Typical Performance Curves
(Continued)
8
C1 = 50pF
VCC = 4.5V
R2 = OPEN
6
4
LINEARITY (%)
f
f2
f0
∆V = 0.5V OVER THE VCC RANGE:
FOR VCO LINEARITY
f’o = f1 + f2
2
f’o - fo
x 100%
LINEARITY = f’
f0
f1
VCOIN = 2.25V ± 1V
2
VCOIN = 2.25V ± 0.45V
0
-2
-4
o
∆V
MIN
∆V
-6
-8
1K
MAX
VVCOIN
1/2VCC
FIGURE 33. DEFINITION OF VCO FREQUENCY LINEARITY
LINEARITY (%)
LINEARITY (%)
4
VCOIN = 1.50V ± 0.4V
0
VCOIN = 1.50V ± 0.3V
-2
0
-2
-4
-6
-6
10K
100K
R1 (OHMS)
1M
DEMODULATOR POWER DISSIPATION, PD (µW)
2
0
-4
-6
10K
100K
R1 (OHMS)
C1 = 50pF
R2 = OPEN
1M
10K
100K
R1 (OHMS)
1M
10M
FIGURE 36. HC4046A VCO LINEARITY vs R1 (VCC = 6V)
VCC = 5.5V,
VCOIN = 2.75V ±1.3V
6
VCC = 4.5V,
VCOIN = 2.25V ±1.0V
4
VCC = 5.5V,
VCOIN = 2.75V ±0.55V
VCC = 4.5V,
VCOIN = 2.25V ±0.45V
VCOIN = 3V ± 0.6V
-8
1K
10M
8
-2
VCOIN = 3V ± 1.5V
2
-4
FIGURE 35. HC4046A VCO LINEARITY vs R1 (VCC = 3V)
LINEARITY (%)
10M
C1 = 50pF
VCC = 6V
R2 = OPEN
6
2
-8
1K
1M
8
C1 = 50pF
VCC = 3V
R2 = OPEN
4
-8
1K
100K
R1 (OHMS)
FIGURE 34. HC4046A VCO LINEARITY vs R1 (VCC = 4.5V)
8
6
10K
10M
104
VCOIN = 0.5 VCC
103
VCC = 6V
102
VCC = 3V
VCC = 4.5V
10
1
1K
10K
100K
1M
RS (OHMS)
FIGURE 37. HCT4046A VCO LINEARITY vs R1 (VCC = 4.5V,
VCC = 5.5V)
FIGURE 38. HC4046A DEMODULATOR POWER DISSIPATION
vs RS (TYP) (VCC = 3V, 4.5V, 6V)
17
CD54HC4046A, CD74HC4046A, CD54HCT4046A, CD74HCT4046A
(Continued)
106
104
VCO POWER DISSIPATION, PD (µW)
DEMODULATOR POWER DISSIPATION, PD (µW)
Typical Performance Curves
VCOIN = 0.5 VCC
R1 = R2 = OPEN
103
VCC = 6V
102
VCC = 3V
VCC = 4.5V
10
VCOIN = 0.5VCC
R2 = RS = OPEN
CL = 50pF
VCC = 6V
C1 = 50pF
105
VCC = 6V
C1 = 1µF
104
VCC = 3V
C1 = 1µF
103
VCC = 3V
C1 = 50pF
VCC = 4.5V
C1 = 1µF
102
1
1K
1K
10K
100K
10K
1M
FIGURE 39. HCT4046A DEMODULATOR POWER DISSIPATION
vs RS (TYP) (VCC = 3V, 4.5V, 6V)
VCO POWER DISSIPATION, PD (µW)
VCO POWER DISSIPATION, PD (µW)
106
105
VCC = 4.5V
C1 = 50pF
104
VCC = 4.5V
C1 = 1µF
VCC = 6V
C1 = 1µF
103
1M
FIGURE 40. HC4046A VCO POWER DISSIPATION vs R1
(C1 = 50pF, 1µF)
VCOIN = 0V (AT fMIN)
R1 = RS = OPEN
CL = 50pF
VCC = 6V
C1 = 50pF
100K
R1 (OHMS)
RS (OHMS)
106
VCC = 4.5V
C1 = 50pF
102
VCC = 5.5V
C1 = 50pF
105
VCOIN = 0.5V
R2 = RS = OPEN
VCC = 4.5V
C1 = 50pF
104
VCC = 5.5V
C1 = 1µF
103
VCC = 4.5V
C1 = 1µF
102
1K
10K
100K
1K
1M
10K
R2 (OHMS)
FIGURE 41. HCT4046A VCO POWER DISSIPATION vs R2
(C1 = 50pF, 1µF)
FIGURE 42. HCT4046A VCO POWER DISSIPATION vs R1
(C1 = 50pF, 1µF)
106
VCO POWER DISSIPATION, PD (µW)
100K
R1 (OHMS)
VCC = 6V
C1 = 50pF
105
VCOIN = 0V (AT fMIN)
R1 = RS = OPEN
CL = 50pF
VCC = 4.5V
C1 = 50pF
VCC = 6V
C1 = 1µF
104
VCC = 3V
C1 = 1µF
VCC = 3V
C1 = 50pF
103
VCC = 4.5V
C1 = 1µF
102
1K
10K
100K
1M
R2 (OHMS)
FIGURE 43. HC4046A VCO POWER DISSIPATION vs R2 (C1 = 50pF, 1µF)
18
1M
CD54HC4046A, CD74HC4046A, CD54HCT4046A, CD74HCT4046A
References should be made to Figures 11 through 15 and
Figures 27 through 32 as indicated in the table.
HC/HCT4046A CPD
CHIP SECTION
HC
HCT
UNIT
Comparator 1
48
50
pF
Comparators 2 and 3
39
48
pF
VCO
61
53
pF
Values of the selected components should be within the
following ranges:
Application Information
This information is a guide for the approximation of values of
external components to be used with the ’HC4046A and
’HCT4046A in a phase-lock-loop system.
SUBJECT
VCO Frequency
Without Extra Offset
R1
Between 3kΩ and 300kΩ
R2
Between 3kΩ and 300kΩ
R1 + R2
Parallel Value > 2.7kΩ
C1
Greater Than 40pF
PHASE
COMPARATOR
PC1, PC2 or PC3
DESIGN CONSIDERATIONS
VCO Frequency Characteristic
With R2 = ∞ and R1 within the range 3kΩ < R1 < 300kΩ, the characteristics of the VCO
operation will be as shown in Figures 11 - 15. (Due to R1, C1 time constant a small offset
remains when R2 = ∞.)
fMAX
fVCO
fo
2fL
fMIN
MIN
1/2 VCC VVCOIN
MAX
FIGURE 44. FREQUENCY CHARACTERISTIC OF VCO OPERATING WITHOUT
OFFSET: fo = CENTER FREQUENCY: 2fL = FREQUENCY LOCK RANGE
VCO Frequency with
Extra Offset
PC1
Selection of R1 and C1
Given fo, determine the values of R1 and C1 using Figures 11 - 15
PC2 or PC3
Given fMAX calculate fo as fMAX/2 and determine the values of R1 and C1 using Figures 11 15. To obtain 2fL: 2fL ≈ 1.2 (VCC - 1.8V)/(R1C1) where valid range of VCOIN is 1.1V < VCOIN
< VCC - 0.9V
PC1, PC2 or PC3
VCO Frequency Characteristic
With R1 and R2 within the ranges 3kΩ < R1 < 300kΩ, 3kΩ, < R2 < 300kΩ, the characteristics
of the VCO operation will be as shown in Figures 27 - 32.
fMAX
fVCO
2fL
fo
fMIN
MIN
1/2 VCC
VVCOIN
MAX
FIGURE 45. FREQUENCY CHARACTERISTIC OF VCO OPERATING WITH OFFSET:
fo = CENTER FREQUENCY: 2fL = FREQUENCY LOCK RANGE
PC1, PC2 or PC3
Selection of R1, R2 and C1
Given fo and fL, offset frequency, fMIN, may be calculated from fMIN ≈ fo - 1.6 fL.
Obtain the values of C1 and R2 by using Figures 27 - 30.
Calculate the values of R1 from Figures 31 - 32.
19
CD54HC4046A, CD74HC4046A, CD54HCT4046A, CD74HCT4046A
SUBJECT
PLL Conditions with
No Signal at the
SIGIN Input
PLL Frequency
Capture Range
PHASE
COMPARATOR
DESIGN CONSIDERATIONS
PC1
VCO adjusts to fo with φDEMOUT = 90o and VVCOIN = 1/2 VCC (see Figure 2)
PC2
VCO adjusts to fMIN with φDEMOUT = -360o and VVCOIN = 0V (see Figure 4)
PC3
VCO adjusts to fMAX with φDEMOUT = 360o and VVCOIN = VCC (see Figure 6)
PC1, PC2 or PC3
Loop Filter Component Selection
|F(jω)|
R3
INPUT
(A)
C2
-1/τ
OUTPUT
ω
τ = R3 x C2
(B) AMPLITUDE CHARACTERISTIC
(C) POLE-ZERO DIAGRAM
1/π (2πfL/τ.)1/2
A small capture range (2fc) is obtained if τ > 2fc ≈
FIGURE 46. SIMPLE LOOP FILTER FOR PLL WITHOUT OFFSET
R3
|F(jω)|
R4
INPUT
m=
R4
R3 + R4
OUTPUT
m
C2
(A) τ1 = R3 x C2;
τ2 = R4 x C2;
τ3 = (R3 + R4) x C2
1/τ3 1/τ2 ω
(B) AMPLITUDE CHARACTERISTIC
-1/τ2 -1/τ3
(C) POLE-ZERO DIAGRAM
FIGURE 47. SIMPLE LOOP FILTER FOR PLL WITH OFFSET
PLL Locks on
Harmonics at Center
Frequency
PC1 or PC3
Yes
PC2
No
Noise Rejection at
Signal Input
PC1
High
PC2 or PC3
Low
AC Ripple Content
when PLL is Locked
PC1
fr = 2fi, large ripple content at φDEMOUT = 90o
PC2
fr = fi, small ripple content at φDEMOUT = 0o
PC3
fr = fSIGIN, large ripple content at φDEMOUT = 180o
20
PACKAGE OPTION ADDENDUM
www.ti.com
9-Oct-2007
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
5962-8875701EA
ACTIVE
CDIP
J
16
1
TBD
A42 SNPB
N / A for Pkg Type
5962-8960901EA
ACTIVE
CDIP
J
16
1
TBD
A42 SNPB
N / A for Pkg Type
Lead/Ball Finish
MSL Peak Temp (3)
CD54HC4046AF
ACTIVE
CDIP
J
16
1
TBD
A42 SNPB
N / A for Pkg Type
CD54HC4046AF3A
ACTIVE
CDIP
J
16
1
TBD
A42 SNPB
N / A for Pkg Type
CD54HCT4046AF3A
ACTIVE
CDIP
J
16
1
TBD
A42 SNPB
N / A for Pkg Type
CD74HC4046AE
ACTIVE
PDIP
N
16
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
CD74HC4046AEE4
ACTIVE
PDIP
N
16
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
CD74HC4046AM
ACTIVE
SOIC
D
16
40
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
CD74HC4046AM96
ACTIVE
SOIC
D
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
CD74HC4046AM96E4
ACTIVE
SOIC
D
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
CD74HC4046AM96G4
ACTIVE
SOIC
D
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
CD74HC4046AME4
ACTIVE
SOIC
D
16
40
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
CD74HC4046AMG4
ACTIVE
SOIC
D
16
40
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
CD74HC4046AMT
ACTIVE
SOIC
D
16
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
CD74HC4046AMTE4
ACTIVE
SOIC
D
16
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
CD74HC4046AMTG4
ACTIVE
SOIC
D
16
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
CD74HC4046ANSR
ACTIVE
SO
NS
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
CD74HC4046ANSRE4
ACTIVE
SO
NS
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
CD74HC4046ANSRG4
ACTIVE
SO
NS
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
CD74HC4046APWR
ACTIVE
TSSOP
PW
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
CD74HC4046APWRE4
ACTIVE
TSSOP
PW
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
CD74HC4046APWRG4
ACTIVE
TSSOP
PW
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
CD74HC4046APWT
ACTIVE
TSSOP
PW
16
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
CD74HC4046APWTE4
ACTIVE
TSSOP
PW
16
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
CD74HC4046APWTG4
ACTIVE
TSSOP
PW
16
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
CD74HCT4046AE
ACTIVE
PDIP
N
16
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
CD74HCT4046AEE4
ACTIVE
PDIP
N
16
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
9-Oct-2007
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
CD74HCT4046AM
ACTIVE
SOIC
D
16
CD74HCT4046AM96
ACTIVE
SOIC
D
CD74HCT4046AM96E4
ACTIVE
SOIC
CD74HCT4046AM96G4
ACTIVE
CD74HCT4046AME4
40
Lead/Ball Finish
MSL Peak Temp (3)
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
D
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SOIC
D
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
ACTIVE
SOIC
D
16
40
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
CD74HCT4046AMG4
ACTIVE
SOIC
D
16
40
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
CD74HCT4046AMT
ACTIVE
SOIC
D
16
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
CD74HCT4046AMTE4
ACTIVE
SOIC
D
16
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
CD74HCT4046AMTG4
ACTIVE
SOIC
D
16
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 2
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
PW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,30
0,19
0,65
14
0,10 M
8
0,15 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
1
7
0°– 8°
A
0,75
0,50
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,10
8
14
16
20
24
28
A MAX
3,10
5,10
5,10
6,60
7,90
9,80
A MIN
2,90
4,90
4,90
6,40
7,70
9,60
DIM
4040064/F 01/97
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-153
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2008, Texas Instruments Incorporated
Similar pages