Features • High Performance, Low Power AVR® 8-Bit Microcontroller • Advanced RISC Architecture • • • • • • • • – 135 Powerful Instructions – Most Single Clock Cycle Execution – 32 x 8 General Purpose Working Registers – Fully Static Operation – Up to 16 MIPS Throughput at 16 MHz – On-Chip 2-cycle Multiplier Non-volatile Program and Data Memories – 64K/128K/256K Bytes of In-System Self-Programmable Flash Endurance: 10,000 Write/Erase Cycles – Optional Boot Code Section with Independent Lock Bits In-System Programming by On-chip Boot Program True Read-While-Write Operation – 4K Bytes EEPROM Endurance: 100,000 Write/Erase Cycles – 8K Bytes Internal SRAM – Up to 64K Bytes Optional External Memory Space – Programming Lock for Software Security JTAG (IEEE std. 1149.1 compliant) Interface – Boundary-scan Capabilities According to the JTAG Standard – Extensive On-chip Debug Support – Programming of Flash, EEPROM, Fuses, and Lock Bits through the JTAG Interface Peripheral Features – Two 8-bit Timer/Counters with Separate Prescaler and Compare Mode – Four 16-bit Timer/Counter with Separate Prescaler, Compare- and Capture Mode – Real Time Counter with Separate Oscillator – Four 8-bit PWM Channels – Six/Twelve PWM Channels with Programmable Resolution from 2 to 16 Bits (ATmega1281/2561, ATmega640/1280/2560) – Output Compare Modulator – 8/16-channel, 10-bit ADC (ATmega1281/2561, ATmega640/1280/2560) – Two/Four Programmable Serial USART (ATmega1281/2561,ATmega640/1280/2560) – Master/Slave SPI Serial Interface – Byte Oriented 2-wire Serial Interface – Programmable Watchdog Timer with Separate On-chip Oscillator – On-chip Analog Comparator – Interrupt and Wake-up on Pin Change Special Microcontroller Features – Power-on Reset and Programmable Brown-out Detection – Internal Calibrated Oscillator – External and Internal Interrupt Sources – Six Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, Standby, and Extended Standby I/O and Packages – 54/86 Programmable I/O Lines (ATmega1281/2561, ATmega640/1280/2560) – 64-pad QFN/MLF, 64-lead TQFP (ATmega1281/2561) – 100-lead TQFP, 100-ball CBGA (ATmega640/1280/2560) – RoHS/Fully Green Temperature Range: – -40°C to 85°C Industrial Ultra-Low Power Consumption – Active Mode: 1 MHz, 1.8V: 510 µA – Power-down Mode: 0.1 µA at 1.8V Speed Grade (see “Maximum speed vs. VCC” on page 377): – ATmega640V/ATmega1280V/ATmega1281V: 0 - 4 MHz @ 1.8 - 5.5V, 0 - 8 MHz @ 2.7 - 5.5V – ATmega2560V/ATmega2561V: 0 - 2 MHz @ 1.8 - 5.5V, 0 - 8 MHz @ 2.7 - 5.5V – ATmega640/ATmega1280/ATmega1281: 0 - 8 MHz @ 2.7 - 5.5V, 0 - 16 MHz @ 4.5 - 5.5V – ATmega2560/ATmega2561: 0 - 16 MHz @ 4.5 - 5.5V 8-bit Microcontroller with 64K/128K/256K Bytes In-System Programmable Flash ATmega640/V ATmega1280/V ATmega1281/V ATmega2560/V ATmega2561/V Preliminary Summary 2549KS–AVR–01/07 Pin Configurations 2 80 PA1 (AD1) 81 PA2 (AD2) 82 PJ7 83 PA0 (AD0) 84 GND 85 VCC 86 PK7 (ADC15/PCINT23) 87 PK5 (ADC13/PCINT21) 88 PK6 (ADC14/PCINT22) 89 PK3 (ADC11/PCINT19) 90 PK4 (ADC12/PCINT20) 91 PK1 (ADC9/PCINT17) PK0 (ADC8/PCINT16) 92 PK2 (ADC10/PCINT18) PF7 (ADC7/TDI) 93 PF5 (ADC5/TMS) 94 PF6 (ADC6/TDO) 95 PF3 (ADC3) 96 PF4 (ADC4/TCK) 97 PF1 (ADC1) 98 PF2 (ADC2) AREF 100 99 PF0 (ADC0) GND AVCC Figure 1. TQFP-pinout ATmega640/1280/2560 79 78 77 76 (OC0B) PG5 1 75 PA3 (AD3) (RXD0/PCINT8) PE0 2 74 PA4 (AD4) (TXD0) PE1 3 73 PA5 (AD5) (XCK0/AIN0) PE2 4 72 PA6 (AD6) (OC3A/AIN1) PE3 5 71 PA7 (AD7) (OC3B/INT4) PE4 6 70 PG2 (ALE) (OC3C/INT5) PE5 7 69 PJ6 (PCINT15) (T3/INT6) PE6 8 68 PJ5 (PCINT14) (CLKO/ICP3/INT7) PE7 9 67 PJ4 (PCINT13) VCC 10 66 PJ3 (PCINT12) GND 11 65 PJ2 (XCK3/PCINT11) (RXD2) PH0 12 64 PJ1 (TXD3/PCINT10) (TXD2) PH1 13 63 PJ0 (RXD3/PCINT9) (XCK2) PH2 14 62 GND (OC4A) PH3 15 61 VCC (OC4B) PH4 16 60 PC7 (A15) (OC4C) PH5 17 59 PC6 (A14) (OC2B) PH6 18 58 PC5 (A13) (SS/PCINT0) PB0 19 57 PC4 (A12) (SCK/PCINT1) PB1 20 56 PC3 (A11) (MOSI/PCINT2) PB2 21 55 PC2 (A10) (MISO/PCINT3) PB3 22 54 PC1 (A9) (OC2A/PCINT4) PB4 23 53 PC0 (A8) (OC1A/PCINT5) PB5 24 52 PG1 (RD) (OC1B/PCINT6) PB6 25 51 PG0 (WR) INDEX CORNER 43 44 45 46 47 48 49 50 (T1) PD6 42 (T0) PD7 41 (ICP1) PD4 40 (XCK1) PD5 39 (TXD1/INT3) PD3 GND XTAL2 38 (SDA/INT1) PD1 VCC 37 (RXD1/INT2) PD2 RESET 36 PL7 (TOSC2) PG3 (TOSC1) PG4 35 (SCL/INT0) PD0 (T4) PH7 34 PL6 33 (OC5C) PL5 32 (OC5B) PL4 31 (OC5A) PL3 30 (T5) PL2 29 (ICP5) PL1 28 XTAL1 27 (ICP4) PL0 26 (OC0A/OC1C/PCINT7) PB7 ATmega640/1280/2560 ATmega640/1280/1281/2560/2561 2549KS–AVR–01/07 ATmega640/1280/1281/2560/2561 Figure 2. CBGA-pinout ATmega640/1280/2560 Top view 1 2 3 4 5 6 Bottom view 7 8 9 10 10 9 8 7 6 5 4 3 2 1 A A B B C C D D E E F F G G H H J J K K Table 1. CBGA-pinout ATmega640/1280/2560. 1 2 3 4 5 6 7 8 9 10 A GND AREF PF0 PF2 PF5 PK0 PK3 PK6 GND VCC B AVCC PG5 PF1 PF3 PF6 PK1 PK4 PK7 PA0 PA2 C PE2 PE0 PE1 PF4 PF7 PK2 PK5 PJ7 PA1 PA3 D PE3 PE4 PE5 PE6 PH2 PA4 PA5 PA6 PA7 PG2 E PE7 PH0 PH1 PH3 PH5 PJ6 PJ5 PJ4 PJ3 PJ2 F VCC PH4 PH6 PB0 PL4 PD1 PJ1 PJ0 PC7 GND G GND PB1 PB2 PB5 PL2 PD0 PD5 PC5 PC6 VCC H PB3 PB4 RESET PL1 PL3 PL7 PD4 PC4 PC3 PC2 J PH7 PG3 PB6 PL0 XTAL2 PL6 PD3 PC1 PC0 PG1 K PB7 PG4 VCC GND XTAL1 PL5 PD2 PD6 PD7 PG0 3 2549KS–AVR–01/07 4 PF7 (ADC7/TDI) GND VCC PA0 (AD0) PA1 (AD1) PA2 (AD2) 54 53 52 51 50 49 PF5 (ADC5/TMS) 57 PF6 (ADC6/TDO) PF4 (ADC4/TCK) 58 55 PF3 (ADC3) 59 56 PF1 (ADC1) PF2 (ADC2) 60 AREF PF0 (ADC0) 62 63 61 AVCC GND (OC0B) PG5 1 48 PA3 (AD3) (RXD0/PCINT8/PDI) PE0 2 47 PA4 (AD4) (TXD0/PDO) PE1 3 46 PA5 (AD5) (XCK0/AIN0) PE2 4 45 PA6 (AD6) (OC3A/AIN1) PE3 5 44 PA7 (AD7) (OC3B/INT4) PE4 6 43 PG2 (ALE) (OC3C/INT5) PE5 7 42 PC7 (A15) (T3/INT6) PE6 8 41 PC6 (A14) (ICP3/CLKO/INT7) PE7 9 40 PC5 (A13) (SS/PCINT0) PB0 10 39 PC4 (A12) (SCK/ PCINT1) PB1 11 38 PC3 (A11) (MOSI/ PCINT2) PB2 12 37 PC2 (A10) (MISO/ PCINT3) PB3 13 36 PC1 (A9) (OC2A/ PCINT4) PB4 14 35 PC0 (A8) (OC1A/PCINT5) PB5 15 34 PG1 (RD) (OC1B/PCINT6) PB6 16 33 PG0 (WR) Note: Disclaimer 64 Figure 3. Pinout ATmega1281/2561 INDEX CORNER 27 28 29 30 31 32 (RXD1/INT2) PD2 (TXD1/INT3) PD3 (ICP1) PD4 (XCK1) PD5 (T1) PD6 (T0) PD7 23 26 22 XTAL2 (SDA/INT1) PD1 21 VCC GND 25 20 RESET 24 19 (TOSC1) PG4 XTAL1 18 (TOSC2) PG3 (SCL/INT0) PD0 17 (OC0A/OC1C/PCINT7) PB7 ATmega1281/2561 The large center pad underneath the QFN/MLF package is made of metal and internally connected to GND. It should be soldered or glued to the board to ensure good mechanical stability. If the center pad is left unconnected, the package might loosen from the board. Typical values contained in this datasheet are based on simulations and characterization of other AVR microcontrollers manufactured on the same process technology. Min. and Max values will be available after the device is characterized. ATmega640/1280/1281/2560/2561 2549KS–AVR–01/07 ATmega640/1280/1281/2560/2561 Overview The ATmega640/1280/1281/2560/2561 is a low-power CMOS 8-bit microcontroller based on the AVR enhanced RISC architecture. By executing powerful instructions in a single clock cycle, the ATmega640/1280/1281/2560/2561 achieves throughputs approaching 1 MIPS per MHz allowing the system designer to optimize power consumption versus processing speed. Block Diagram Figure 4. Block Diagram PF7..0 PK7..0 PORT F (8) PORT K (8) PJ7..0 PE7..0 VCC RESET GND Power Supervision POR / BOD & RESET PORT J (8) PORT E (8) Watchdog Timer Watchdog Oscillator Analog Comparator JTAG A/D Converter EEPROM Internal Bandgap reference USART 0 XTAL1 Oscillator Circuits / Clock Generation 16bit T/C 3 USART 3 16bit T/C 5 XTAL2 CPU PA7..0 PORT A (8) 16bit T/C 4 USART 1 PG5..0 PORT G (6) XRAM PC7..0 PORT C (8) TWI FLASH SPI SRAM 16bit T/C 1 8bit T/C 0 USART 2 8bit T/C 2 NOTE: Shaded parts only available in the 100-pin version. Complete functionality for the ADC, T/C4, and T/C5 only available in the 100-pin version. PORT D (8) PORT B (8) PORT H (8) PORT L (8) PD7..0 PB7..0 PH7..0 PL7..0 5 2549KS–AVR–01/07 The AVR core combines a rich instruction set with 32 general purpose working registers. All the 32 registers are directly connected to the Arithmetic Logic Unit (ALU), allowing two independent registers to be accessed in one single instruction executed in one clock cycle. The resulting architecture is more code efficient while achieving throughputs up to ten times faster than conventional CISC microcontrollers. The ATmega640/1280/1281/2560/2561 provides the following features: 64K/128K/256K bytes of In-System Programmable Flash with Read-While-Write capabilities, 4K bytes EEPROM, 8K bytes SRAM, 54/86 general purpose I/O lines, 32 general purpose working registers, Real Time Counter (RTC), six flexible Timer/Counters with compare modes and PWM, 4 USARTs, a byte oriented 2-wire Serial Interface, a 16-channel, 10bit ADC with optional differential input stage with programmable gain, programmable Watchdog Timer with Internal Oscillator, an SPI serial port, IEEE std. 1149.1 compliant JTAG test interface, also used for accessing the On-chip Debug system and programming and six software selectable power saving modes. The Idle mode stops the CPU while allowing the SRAM, Timer/Counters, SPI port, and interrupt system to continue functioning. The Power-down mode saves the register contents but freezes the Oscillator, disabling all other chip functions until the next interrupt or Hardware Reset. In Power-save mode, the asynchronous timer continues to run, allowing the user to maintain a timer base while the rest of the device is sleeping. The ADC Noise Reduction mode stops the CPU and all I/O modules except Asynchronous Timer and ADC, to minimize switching noise during ADC conversions. In Standby mode, the Crystal/Resonator Oscillator is running while the rest of the device is sleeping. This allows very fast start-up combined with low power consumption. In Extended Standby mode, both the main Oscillator and the Asynchronous Timer continue to run. The device is manufactured using Atmel’s high-density nonvolatile memory technology. The On-chip ISP Flash allows the program memory to be reprogrammed in-system through an SPI serial interface, by a conventional nonvolatile memory programmer, or by an On-chip Boot program running on the AVR core. The boot program can use any interface to download the application program in the application Flash memory. Software in the Boot Flash section will continue to run while the Application Flash section is updated, providing true Read-While-Write operation. By combining an 8-bit RISC CPU with In-System Self-Program mable Flash on a monolithic ch ip, the Atmel ATmega640/1280/1281/2560/2561 is a powerful microcontroller that provides a highly flexible and cost effective solution to many embedded control applications. The ATmega640/1280/1281/2560/2561 AVR is supported with a full suite of program and system development tools including: C compilers, macro assemblers, program debugger/simulators, in-circuit emulators, and evaluation kits. 6 ATmega640/1280/1281/2560/2561 2549KS–AVR–01/07 ATmega640/1280/1281/2560/2561 Comparison Between ATmega1281/2561 and ATmega640/1280/2560 Each device in the ATmega640/1280/1281/2560/2561 family differs only in memory size and number of pins. Table 2 summarizes the different configurations for the six devices. Table 2. Configuration Summary Device Flash EEPROM RAM General Purpose I/O pins 16 bits resolution PWM channels Serial USARTs ADC Channels ATmega640 64KB 4KB 8KB 86 12 4 16 ATmega1280 128KB 4KB 8KB 86 12 4 16 ATmega1281 128KB 4KB 8KB 54 6 2 8 ATmega2560 256KB 4KB 8KB 86 12 4 16 ATmega2561 256KB 4KB 8KB 54 6 2 8 Pin Descriptions VCC Digital supply voltage. GND Ground. Port A (PA7..PA0) Port A is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port A output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port A pins that are externally pulled low will source current if the pull-up resistors are activated. The Port A pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port A also serves the functions of various special features of the ATmega640/1280/1281/2560/2561 as listed on page 91. Port B (PB7..PB0) Port B is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port B output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port B pins that are externally pulled low will source current if the pull-up resistors are activated. The Port B pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port B has better driving capabilities than the other ports. Port B also serves the functions of various special features of the ATmega640/1280/1281/2560/2561 as listed on page 92. Port C (PC7..PC0) Port C is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port C output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port C pins that are externally pulled low will source current if the pull-up resistors are activated. The Port C pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port C also serves the functions of special ATmega640/1280/1281/2560/2561 as listed on page 95. Port D (PD7..PD0) features of the Port D is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port D output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port D pins that are externally pulled low will source 7 2549KS–AVR–01/07 current if the pull-up resistors are activated. The Port D pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port D also serves the functions of various special features of the ATmega640/1280/1281/2560/2561 as listed on page 97. Port E (PE7..PE0) Port E is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port E output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port E pins that are externally pulled low will source current if the pull-up resistors are activated. The Port E pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port E also serves the functions of various special features of the ATmega640/1280/1281/2560/2561 as listed on page 99. Port F (PF7..PF0) Port F serves as analog inputs to the A/D Converter. Port F also serves as an 8-bit bi-directional I/O port, if the A/D Converter is not used. Port pins can provide internal pull-up resistors (selected for each bit). The Port F output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port F pins that are externally pulled low will source current if the pull-up resistors are activated. The Port F pins are tri-stated when a reset condition becomes active, even if the clock is not running. If the JTAG interface is enabled, the pull-up resistors on pins PF7(TDI), PF5(TMS), and PF4(TCK) will be activated even if a reset occurs. Port F also serves the functions of the JTAG interface. Port G (PG5..PG0) Port G is a 6-bit I/O port with internal pull-up resistors (selected for each bit). The Port G output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port G pins that are externally pulled low will source current if the pull-up resistors are activated. The Port G pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port G also serves the functions of various special features of the ATmega640/1280/1281/2560/2561 as listed on page 105. Port H (PH7..PH0) Port H is a 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port H output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port H pins that are externally pulled low will source current if the pull-up resistors are activated. The Port H pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port H also serves the functions of various special features of the ATmega640/1280/2560 as listed on page 107. Port J (PJ7..PJ0) Port J is a 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port J output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port J pins that are externally pulled low will source current if the pull-up resistors are activated. The Port J pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port J also serves the functions of various special features of the ATmega640/1280/2560 as listed on page 109. Port K (PK7..PK0) 8 Port K serves as analog inputs to the A/D Converter. ATmega640/1280/1281/2560/2561 2549KS–AVR–01/07 ATmega640/1280/1281/2560/2561 Port K is a 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port K output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port K pins that are externally pulled low will source current if the pull-up resistors are activated. The Port K pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port K also serves the functions of various special features of the ATmega640/1280/2560 as listed on page 111. Port L (PL7..PL0) Port L is a 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port L output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port L pins that are externally pulled low will source current if the pull-up resistors are activated. The Port L pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port L also serves the functions of various special features of the ATmega640/1280/2560 as listed on page 113. RESET Reset input. A low level on this pin for longer than the minimum pulse length will generate a reset, even if the clock is not running. The minimum pulse length is given in Table 26 on page 58. Shorter pulses are not guaranteed to generate a reset. XTAL1 Input to the inverting Oscillator amplifier and input to the internal clock operating circuit. XTAL2 Output from the inverting Oscillator amplifier. AVCC AVCC is the supply voltage pin for Port F and the A/D Converter. It should be externally connected to VCC, even if the ADC is not used. If the ADC is used, it should be connected to VCC through a low-pass filter. AREF This is the analog reference pin for the A/D Converter. Resources A comprehensive set of development tools and application notes, and datasheets are available for download on http://www.atmel.com/avr. 9 2549KS–AVR–01/07 Register Summary Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (0x1FF) Reserved - - - - - - - - - - - - - - - - - - - 10 ... Reserved (0x13F) Reserved (0x13E) Reserved (0x13D) Reserved (0x13C) Reserved (0x13B) Reserved (0x13A) Reserved (0x139) Reserved (0x138) Reserved (0x137) Reserved (0x136) UDR3 (0x135) UBRR3H USART3 I/O Data Register (0x134) UBRR3L (0x133) Reserved - - (0x132) UCSR3C UMSEL31 (0x131) UCSR3B RXCIE3 (0x130) UCSR3A - page 227 USART3 Baud Rate Register High Byte page 231 USART3 Baud Rate Register Low Byte - - - UMSEL30 UPM31 UPM30 TXCIE3 UDRIE3 RXEN3 RXC3 TXC3 UDRE3 Page page 231 - - - USBS3 UCSZ31 UCSZ30 UCPOL3 TXEN3 UCSZ32 RXB83 TXB83 page 243 FE3 DOR3 UPE3 U2X3 MPCM3 page 242 page 244 (0x12F) Reserved - - - - - - - - (0x12E) Reserved - - - - - - - - (0x12D) OCR5CH Timer/Counter5 - Output Compare Register C High Byte page 167 (0x12C) OCR5CL Timer/Counter5 - Output Compare Register C Low Byte page 167 (0x12B) OCR5BH Timer/Counter5 - Output Compare Register B High Byte page 167 (0x12A) OCR5BL Timer/Counter5 - Output Compare Register B Low Byte page 167 (0x129) OCR5AH Timer/Counter5 - Output Compare Register A High Byte page 167 (0x128) OCR5AL Timer/Counter5 - Output Compare Register A Low Byte page 167 (0x127) ICR5H Timer/Counter5 - Input Capture Register High Byte page 168 (0x126) ICR5L Timer/Counter5 - Input Capture Register Low Byte page 168 (0x125) TCNT5H Timer/Counter5 - Counter Register High Byte page 165 (0x124) TCNT5L Timer/Counter5 - Counter Register Low Byte (0x123) Reserved - - - (0x122) TCCR5C FOC5A FOC5B FOC5C - - - - - page 164 (0x121) TCCR5B ICNC5 ICES5 - WGM53 WGM52 CS52 CS51 CS50 page 162 page 160 - - page 165 - - - (0x120) TCCR5A COM5A1 COM5A0 COM5B1 COM5B0 COM5C1 COM5C0 WGM51 WGM50 (0x11F) Reserved - - - - - - - - (0x11E) Reserved - - - - - - - - (0x11D) Reserved - - - - - - - - (0x11C) Reserved - - - - - - - - (0x11B) Reserved - - - - - - - - (0x11A) Reserved - - - - - - - - (0x119) Reserved - - - - - - - - (0x118) Reserved - - - - - - - - (0x117) Reserved - - - - - - - - (0x116) Reserved - - - - - - - - (0x115) Reserved - - - - - - - - (0x114) Reserved - - - - - - - - (0x113) Reserved - - - - - - - - (0x112) Reserved - - - - - - - - (0x111) Reserved - - - - - - - - (0x110) Reserved - - - - - - - - (0x10F) Reserved - - - - - - - - (0x10E) Reserved - - - - - - - - (0x10D) Reserved - - - - - - - - (0x10C) Reserved - - - - - - - - (0x10B) PORTL PORTL7 PORTL6 PORTL5 PORTL4 PORTL3 PORTL2 PORTL1 PORTL0 page 118 (0x10A) DDRL DDL7 DDL6 DDL5 DDL4 DDL3 DDL2 DDL1 DDL0 page 118 (0x109) PINL PINL7 PINL6 PINL5 PINL4 PINL3 PINL2 PINL1 PINL0 page 118 (0x108) PORTK PORTK7 PORTK6 PORTK5 PORTK4 PORTK3 PORTK2 PORTK1 PORTK0 page 118 (0x107) DDRK DDK7 DDK6 DDK5 DDK4 DDK3 DDK2 DDK1 DDK0 page 118 page 118 (0x106) PINK PINK7 PINK6 PINK5 PINK4 PINK3 PINK2 PINK1 PINK0 (0x105) PORTJ PORTJ7 PORTJ6 PORTJ5 PORTJ4 PORTJ3 PORTJ2 PORTJ1 PORTJ0 page 118 (0x104) DDRJ DDJ7 DDJ6 DDJ5 DDJ4 DDJ3 DDJ2 DDJ1 DDJ0 page 118 (0x103) PINJ PINJ7 PINJ6 PINJ5 PINJ4 PINJ3 PINJ2 PINJ1 PINJ0 page 118 (0x102) PORTH PORTH7 PORTH6 PORTH5 PORTH4 PORTH3 PORTH2 PORTH1 PORTH0 page 117 ATmega640/1280/1281/2560/2561 2549KS–AVR–01/07 ATmega640/1280/1281/2560/2561 Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Page (0x101) DDRH DDH7 DDH6 DDH5 DDH4 DDH3 DDH2 DDH1 DDH0 page 117 (0x100) PINH PINH7 PINH6 PINH5 PINH4 PINH3 PINH2 PINH1 PINH0 page 117 (0xFF) Reserved - - - - - - - - (0xFE) Reserved - - - - - - - - (0xFD) Reserved - - - - - - - - (0xFC) Reserved - - - - - - - - (0xFB) Reserved - - - - - - - - (0xFA) Reserved - - - - - - - - (0xF9) Reserved - - - - - - - - (0xF8) Reserved - - - - - - - - (0xF7) Reserved - - - - - - - - (0xF6) Reserved - - - - - - - - (0xF5) Reserved - - - - - - - - (0xF4) Reserved - - - - - - - - (0xF3) Reserved - - - - - - - - (0xF2) Reserved - - - - - - - - (0xF1) Reserved - - - - - - - - (0xF0) Reserved - - - - - - - - (0xEF) Reserved - - - - - - - - (0xEE) Reserved - - - - - - - - (0xED) Reserved - - - - - - - - (0xEC) Reserved - - - - - - - - (0xEB) Reserved - - - - - - - (0xEA) Reserved - - - - - - - - (0xE9) Reserved - - - - - - - - (0xE8) Reserved - - - - - - - - (0xE7) Reserved - - - - - - - (0xE6) Reserved - - - - - - - - (0xE5) Reserved - - - - - - - - (0xE4) Reserved - - - - - - - - (0xE3) Reserved - - - - - - - (0xE2) Reserved - - - - - - - (0xE1) Reserved - - - - - - - (0xE0) Reserved - - - - - - - (0xDF) Reserved - - - - - - - - (0xDE) Reserved - - - - - - - - (0xDD) Reserved - - - - - - - (0xDC) Reserved - - - - - - - - (0xDB) Reserved - - - - - - - - (0xDA) Reserved - - - - - - - - (0xD9) Reserved - - - - - - - (0xD8) Reserved - - - - - - - - (0xD7) Reserved - - - - - - - - (0xD6) UDR2 (0xD5) UBRR2H - USART2 I/O Data Register - page 227 - - - USART2 Baud Rate Register High Byte page 231 - - - - - - (0xD4) UBRR2L (0xD3) Reserved - - (0xD2) UCSR2C UMSEL21 UMSEL20 UPM21 UPM20 USBS2 UCSZ21 UCSZ20 UCPOL2 (0xD1) UCSR2B RXCIE2 TXCIE2 UDRIE2 RXEN2 TXEN2 UCSZ22 RXB82 TXB82 page 243 (0xD0) UCSR2A RXC2 TXC2 UDRE2 FE2 DOR2 UPE2 U2X2 MPCM2 page 242 - - - - - - - - (0xCF) Reserved (0xCE) UDR1 (0xCD) UBRR1H USART2 Baud Rate Register Low Byte page 231 USART1 I/O Data Register - - - (0xCC) UBRR1L (0xCB) Reserved - - (0xCA) UCSR1C UMSEL11 UMSEL10 (0xC9) UCSR1B RXCIE1 TXCIE1 (0xC8) UCSR1A RXC1 TXC1 UDRE1 (0xC7) Reserved - - - (0xC6) UDR0 (0xC5) UBRR0H - page 244 page 227 USART1 Baud Rate Register High Byte page 231 USART1 Baud Rate Register Low Byte page 231 - - - - - UPM11 UPM10 USBS1 UCSZ11 UCSZ10 UCPOL1 UDRIE1 RXEN1 TXEN1 UCSZ12 RXB81 TXB81 page 243 FE1 DOR1 UPE1 U2X1 MPCM1 page 242 - - - - - USART0 I/O Data Register - page 244 page 227 - - - USART0 Baud Rate Register High Byte page 231 - - - - - - (0xC4) UBRR0L (0xC3) Reserved - - USART0 Baud Rate Register Low Byte page 231 (0xC2) UCSR0C UMSEL01 UMSEL00 UPM01 UPM00 USBS0 UCSZ01 UCSZ00 UCPOL0 (0xC1) UCSR0B RXCIE0 TXCIE0 UDRIE0 RXEN0 TXEN0 UCSZ02 RXB80 TXB80 page 243 (0xC0) UCSR0A RXC0 TXC0 UDRE0 FE0 DOR0 UPE0 U2X0 MPCM0 page 243 page 244 11 2549KS–AVR–01/07 Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (0xBF) Reserved - - - - - - - - 12 Page (0xBE) Reserved - - - - - - - (0xBD) TWAMR TWAM6 TWAM5 TWAM4 TWAM3 TWAM2 TWAM1 TWAM0 - (0xBC) TWCR TWINT TWEA TWSTA TWSTO TWWC TWEN - TWIE (0xBB) TWDR (0xBA) TWAR TWA6 TWA5 TWA4 TWA3 TWA2 TWA1 TWA0 TWGCE (0xB9) TWSR TWS7 TWS6 TWS5 TWS4 TWS3 - TWPS1 TWPS0 (0xB8) TWBR (0xB7) Reserved - - - - - - - - (0xB6) ASSR - EXCLK AS2 TCN2UB OCR2AUB OCR2BUB TCR2AUB TCR2BUB (0xB5) Reserved - - - - - - - - (0xB4) OCR2B Timer/Counter2 Output Compare Register B (0xB3) OCR2A Timer/Counter2 Output Compare Register A page 195 (0xB2) TCNT2 Timer/Counter2 (8 Bit) page 195 (0xB1) TCCR2B FOC2A FOC2B - - WGM22 CS22 CS21 CS20 page 194 (0xB0) TCCR2A COM2A1 COM2A0 COM2B1 COM2B0 - - WGM21 WGM20 page 195 (0xAF) Reserved - - - - - - - - - - - - - - - - 2-wire Serial Interface Data Register page 274 page 271 page 273 2-wire Serial Interface Bit Rate Register page 273 page 272 page 271 page 188 page 195 (0xAE) Reserved (0xAD) OCR4CH Timer/Counter4 - Output Compare Register C High Byte page 167 (0xAC) OCR4CL Timer/Counter4 - Output Compare Register C Low Byte page 167 (0xAB) OCR4BH Timer/Counter4 - Output Compare Register B High Byte page 166 (0xAA) OCR4BL Timer/Counter4 - Output Compare Register B Low Byte page 166 (0xA9) OCR4AH Timer/Counter4 - Output Compare Register A High Byte page 166 (0xA8) OCR4AL Timer/Counter4 - Output Compare Register A Low Byte page 166 (0xA7) ICR4H Timer/Counter4 - Input Capture Register High Byte page 168 (0xA6) ICR4L Timer/Counter4 - Input Capture Register Low Byte page 168 (0xA5) TCNT4H Timer/Counter4 - Counter Register High Byte page 165 (0xA4) TCNT4L (0xA3) Reserved - - - Timer/Counter4 - Counter Register Low Byte (0xA2) TCCR4C FOC4A FOC4B FOC4C - - - - - page 164 (0xA1) TCCR4B ICNC4 ICES4 - WGM43 WGM42 CS42 CS41 CS40 page 162 (0xA0) TCCR4A COM4A1 COM4A0 COM4B1 COM4B0 COM4C1 COM4C0 WGM41 WGM40 page 160 (0x9F) Reserved - - - - - - - - - - - - - - - - - - page 165 - - - (0x9E) Reserved (0x9D) OCR3CH Timer/Counter3 - Output Compare Register C High Byte page 166 (0x9C) OCR3CL Timer/Counter3 - Output Compare Register C Low Byte page 166 (0x9B) OCR3BH Timer/Counter3 - Output Compare Register B High Byte page 166 (0x9A) OCR3BL Timer/Counter3 - Output Compare Register B Low Byte page 166 (0x99) OCR3AH Timer/Counter3 - Output Compare Register A High Byte page 166 (0x98) OCR3AL Timer/Counter3 - Output Compare Register A Low Byte page 166 (0x97) ICR3H Timer/Counter3 - Input Capture Register High Byte page 168 (0x96) ICR3L Timer/Counter3 - Input Capture Register Low Byte page 168 (0x95) TCNT3H Timer/Counter3 - Counter Register High Byte page 165 (0x94) TCNT3L Timer/Counter3 - Counter Register Low Byte (0x93) Reserved - - - (0x92) TCCR3C FOC3A FOC3B FOC3C - - - - - page 164 (0x91) TCCR3B ICNC3 ICES3 - WGM33 WGM32 CS32 CS31 CS30 page 162 page 160 - - page 165 - - - (0x90) TCCR3A COM3A1 COM3A0 COM3B1 COM3B0 COM3C1 COM3C0 WGM31 WGM30 (0x8F) Reserved - - - - - - - - - - - - - - - - (0x8E) Reserved (0x8D) OCR1CH Timer/Counter1 - Output Compare Register C High Byte page 166 (0x8C) OCR1CL Timer/Counter1 - Output Compare Register C Low Byte page 166 (0x8B) OCR1BH Timer/Counter1 - Output Compare Register B High Byte page 166 (0x8A) OCR1BL Timer/Counter1 - Output Compare Register B Low Byte page 166 (0x89) OCR1AH Timer/Counter1 - Output Compare Register A High Byte page 166 (0x88) OCR1AL Timer/Counter1 - Output Compare Register A Low Byte page 166 (0x87) ICR1H Timer/Counter1 - Input Capture Register High Byte page 168 (0x86) ICR1L Timer/Counter1 - Input Capture Register Low Byte page 168 (0x85) TCNT1H Timer/Counter1 - Counter Register High Byte page 165 (0x84) TCNT1L Timer/Counter1 - Counter Register Low Byte (0x83) Reserved - - - (0x82) TCCR1C FOC1A FOC1B FOC1C - - - - - page 164 (0x81) TCCR1B ICNC1 ICES1 - WGM13 WGM12 CS12 CS11 CS10 page 162 page 160 - - page 165 - - - (0x80) TCCR1A COM1A1 COM1A0 COM1B1 COM1B0 COM1C1 COM1C0 WGM11 WGM10 (0x7F) DIDR1 - - - - - - AIN1D AIN0D page 278 (0x7E) DIDR0 ADC7D ADC6D ADC5D ADC4D ADC3D ADC2D ADC1D ADC0D page 300 ATmega640/1280/1281/2560/2561 2549KS–AVR–01/07 ATmega640/1280/1281/2560/2561 Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Page (0x7D) DIDR2 ADC15D ADC14D ADC13D ADC12D ADC11D ADC10D ADC9D ADC8D page 300 (0x7C) ADMUX REFS1 REFS0 ADLAR MUX4 MUX3 MUX2 MUX1 MUX0 page 294 (0x7B) ADCSRB - ACME - - MUX5 ADTS2 ADTS1 ADTS0 page 277,295,,299 (0x7A) ADCSRA ADEN ADSC ADATE ADIF ADIE ADPS2 ADPS1 ADPS0 (0x79) ADCH (0x78) ADCL (0x77) Reserved (0x76) (0x75) ADC Data Register High byte page 297 page 298 ADC Data Register Low byte page 298 - - - - - - - - Reserved - - - - - - - - XMCRB XMBK - - - - XMM2 XMM1 XMM0 (0x74) XMCRA SRE SRL2 SRL1 SRL0 SRW11 SRW10 SRW01 SRW00 page 34 (0x73) TIMSK5 - - ICIE5 - OCIE5C OCIE5B OCIE5A TOIE5 page 169 (0x72) TIMSK4 - - ICIE4 - OCIE4C OCIE4B OCIE4A TOIE4 page 169 (0x71) TIMSK3 - - ICIE3 - OCIE3C OCIE3B OCIE3A TOIE3 page 169 (0x70) TIMSK2 - - - - - OCIE2B OCIE2A TOIE2 page 197 (0x6F) TIMSK1 - - ICIE1 - OCIE1C OCIE1B OCIE1A TOIE1 page 169 (0x6E) TIMSK0 - - - - - OCIE0B OCIE0A TOIE0 page 135 page 36 (0x6D) PCMSK2 PCINT23 PCINT22 PCINT21 PCINT20 PCINT19 PCINT18 PCINT17 PCINT16 page 81 (0x6C) PCMSK1 PCINT15 PCINT14 PCINT13 PCINT12 PCINT11 PCINT10 PCINT9 PCINT8 page 81 (0x6B) PCMSK0 PCINT7 PCINT6 PCINT5 PCINT4 PCINT3 PCINT2 PCINT1 PCINT0 page 82 (0x6A) EICRB ISC71 ISC70 ISC61 ISC60 ISC51 ISC50 ISC41 ISC40 page 79 (0x69) EICRA ISC31 ISC30 ISC21 ISC20 ISC11 ISC10 ISC01 ISC00 page 78 (0x68) PCICR - - - - - PCIE2 PCIE1 PCIE0 page 80 (0x67) Reserved - - - - - - - - (0x66) OSCCAL (0x65) PRR1 - - PRTIM5 PRTIM4 PRTIM3 PRUSART3 PRUSART2 PRUSART1 page 56 (0x64) PRR0 PRTWI PRTIM2 PRTIM0 - PRTIM1 PRSPI PRUSART0 PRADC page 55 (0x63) Reserved - - - - - - - - (0x62) Reserved - - - - - - - - (0x61) CLKPR CLKPCE - - - CLKPS3 CLKPS2 CLKPS1 CLKPS0 page 48 (0x60) WDTCSR WDIF WDIE WDP3 WDCE WDE WDP2 WDP1 WDP0 page 66 Oscillator Calibration Register page 48 0x3F (0x5F) SREG I T H S V N Z C page 12 0x3E (0x5E) SPH SP15 SP14 SP13 SP12 SP11 SP10 SP9 SP8 page 14 0x3D (0x5D) SPL SP7 SP6 SP5 SP4 SP3 SP2 SP1 SP0 page 14 0x3C (0x5C) EIND - - - - - - - EIND0 page 15 0x3B (0x5B) RAMPZ - - - - - - RAMPZ1 RAMPZ0 page 15 0x3A (0x5A) Reserved - - - - - - - - 0x39 (0x59) Reserved - - - - - - - - 0x38 (0x58) Reserved - - - - - - - - 0x37 (0x57) SPMCSR SPMIE RWWSB SIGRD RWWSRE BLBSET PGWRT PGERS SPMEN 0x36 (0x56) Reserved - - - - - - - - 0x35 (0x55) MCUCR JTD - - PUD - - IVSEL IVCE page 66,76,115,314 0x34 (0x54) MCUSR - - - JTRF WDRF BORF EXTRF PORF page 314 0x33 (0x53) SMCR - - - - SM2 SM1 SM0 SE page 51 0x32 (0x52) Reserved - - - - - - - - 0x31 (0x51) OCDR OCDR7 OCDR6 OCDR5 OCDR4 OCDR3 OCDR2 OCDR1 OCDR0 page 307 0x30 (0x50) ACSR ACD ACBG ACO ACI ACIE ACIC ACIS1 ACIS0 page 277 0x2F (0x4F) Reserved - - - - - - - - 0x2E (0x4E) SPDR 0x2D (0x4D) SPSR SPIF WCOL - - - - - SPI2X page 207 0x2C (0x4C) SPCR SPIE SPE DORD MSTR CPOL CPHA SPR1 SPR0 page 206 0x2B (0x4B) GPIOR2 General Purpose I/O Register 2 0x2A (0x4A) GPIOR1 General Purpose I/O Register 1 0x29 (0x49) Reserved 0x28 (0x48) OCR0B Timer/Counter0 Output Compare Register B 0x27 (0x47) OCR0A Timer/Counter0 Output Compare Register A page 134 0x26 (0x46) TCNT0 Timer/Counter0 (8 Bit) page 134 0x25 (0x45) TCCR0B FOC0A FOC0B - - WGM02 CS02 CS01 CS00 0x24 (0x44) TCCR0A COM0A1 COM0A0 COM0B1 COM0B0 - - WGM01 WGM00 page 130 0x23 (0x43) GTCCR TSM - - - - - PSRASY PSRSYNC page 173, 198 - - - 0x22 (0x42) EEARH 0x21 (0x41) EEARL 0x20 (0x40) EEDR 0x1F (0x3F) EECR SPI Data Register page 340 - - - - page 208 page 34 page 34 - - - - page 134 EEPROM Address Register High Byte page 32 EEPROM Address Register Low Byte page 32 EEPROM Data Register - - EEPM1 EEPM0 EERIE page 133 page 32 EEMPE EEPE EERE page 32 0x1E (0x3E) GPIOR0 0x1D (0x3D) EIMSK INT7 INT6 INT5 General Purpose I/O Register 0 INT4 INT3 INT2 INT1 INT0 page 79 page 34 0x1C (0x3C) EIFR INTF7 INTF6 INTF5 INTF4 INTF3 INTF2 INTF1 INTF0 page 80 13 2549KS–AVR–01/07 Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Page 0x1B (0x3B) PCIFR - - - - - PCIF2 PCIF1 PCIF0 page 81 0x1A (0x3A) TIFR5 - - ICF5 - OCF5C OCF5B OCF5A TOV5 page 169 0x19 (0x39) TIFR4 - - ICF4 - OCF4C OCF4B OCF4A TOV4 page 170 0x18 (0x38) TIFR3 - - ICF3 - OCF3C OCF3B OCF3A TOV3 page 170 0x17 (0x37) TIFR2 - - - - - OCF2B OCF2A TOV2 page 197 0x16 (0x36) TIFR1 - - ICF1 - OCF1C OCF1B OCF1A TOV1 page 170 0x15 (0x35) TIFR0 - - - - - OCF0B OCF0A TOV0 page 135 0x14 (0x34) PORTG - - PORTG5 PORTG4 PORTG3 PORTG2 PORTG1 PORTG0 page 117 0x13 (0x33) DDRG - - DDG5 DDG4 DDG3 DDG2 DDG1 DDG0 page 117 0x12 (0x32) PING - - PING5 PING4 PING3 PING2 PING1 PING0 page 117 0x11 (0x31) PORTF PORTF7 PORTF6 PORTF5 PORTF4 PORTF3 PORTF2 PORTF1 PORTF0 page 116 0x10 (0x30) DDRF DDF7 DDF6 DDF5 DDF4 DDF3 DDF2 DDF1 DDF0 page 117 page 117 0x0F (0x2F) PINF PINF7 PINF6 PINF5 PINF4 PINF3 PINF2 PINF1 PINF0 0x0E (0x2E) PORTE PORTE7 PORTE6 PORTE5 PORTE4 PORTE3 PORTE2 PORTE1 PORTE0 page 116 0x0D (0x2D) DDRE DDE7 DDE6 DDE5 DDE4 DDE3 DDE2 DDE1 DDE0 page 116 page 116 0x0C (0x2C) PINE PINE7 PINE6 PINE5 PINE4 PINE3 PINE2 PINE1 PINE0 0x0B (0x2B) PORTD PORTD7 PORTD6 PORTD5 PORTD4 PORTD3 PORTD2 PORTD1 PORTD0 page 116 0x0A (0x2A) DDRD DDD7 DDD6 DDD5 DDD4 DDD3 DDD2 DDD1 DDD0 page 116 page 116 0x09 (0x29) PIND PIND7 PIND6 PIND5 PIND4 PIND3 PIND2 PIND1 PIND0 0x08 (0x28) PORTC PORTC7 PORTC6 PORTC5 PORTC4 PORTC3 PORTC2 PORTC1 PORTC0 page 116 0x07 (0x27) DDRC DDC7 DDC6 DDC5 DDC4 DDC3 DDC2 DDC1 DDC0 page 116 page 116 0x06 (0x26) PINC PINC7 PINC6 PINC5 PINC4 PINC3 PINC2 PINC1 PINC0 0x05 (0x25) PORTB PORTB7 PORTB6 PORTB5 PORTB4 PORTB3 PORTB2 PORTB1 PORTB0 page 115 0x04 (0x24) DDRB DDB7 DDB6 DDB5 DDB4 DDB3 DDB2 DDB1 DDB0 page 115 page 115 0x03 (0x23) PINB PINB7 PINB6 PINB5 PINB4 PINB3 PINB2 PINB1 PINB0 0x02 (0x22) PORTA PORTA7 PORTA6 PORTA5 PORTA4 PORTA3 PORTA2 PORTA1 PORTA0 page 115 0x01 (0x21) DDRA DDA7 DDA6 DDA5 DDA4 DDA3 DDA2 DDA1 DDA0 page 115 0x00 (0x20) PINA PINA7 PINA6 PINA5 PINA4 PINA3 PINA2 PINA1 PINA0 page 115 Note: 1. For compatibility with future devices, reserved bits should be written to zero if accessed. Reserved I/O memory addresses should never be written. 2. I/O registers within the address range $00 - $1F are directly bit-accessible using the SBI and CBI instructions. In these registers, the value of single bits can be checked by using the SBIS and SBIC instructions. 3. Some of the status flags are cleared by writing a logical one to them. Note that the CBI and SBI instructions will operate on all bits in the I/O register, writing a one back into any flag read as set, thus clearing the flag. The CBI and SBI instructions work with registers 0x00 to 0x1F only. 4. When using the I/O specific commands IN and OUT, the I/O addresses $00 - $3F must be used. When addressing I/O registers as data space using LD and ST instructions, $20 must be added to these addresses. The ATmega640/1280/1281/2560/2561 is a complex microcontroller with more peripheral units than can be supported within the 64 location reserved in Opcode for the IN and OUT instructions. For the Extended I/O space from $60 - $1FF in SRAM, only the ST/STS/STD and LD/LDS/LDD instructions can be used. 14 ATmega640/1280/1281/2560/2561 2549KS–AVR–01/07 ATmega640/1280/1281/2560/2561 Instruction Set Summary Mnemonics Operands Description Operation Flags #Clocks ARITHMETIC AND LOGIC INSTRUCTIONS ADD Rd, Rr Add two Registers Rd ← Rd + Rr Z,C,N,V,H 1 ADC Rd, Rr Add with Carry two Registers Rd ← Rd + Rr + C Z,C,N,V,H 1 ADIW Rdl,K Add Immediate to Word Rdh:Rdl ← Rdh:Rdl + K Z,C,N,V,S 2 SUB Rd, Rr Subtract two Registers Rd ← Rd - Rr Z,C,N,V,H 1 SUBI Rd, K Subtract Constant from Register Rd ← Rd - K Z,C,N,V,H 1 SBC Rd, Rr Subtract with Carry two Registers Rd ← Rd - Rr - C Z,C,N,V,H 1 SBCI Rd, K Subtract with Carry Constant from Reg. Rd ← Rd - K - C Z,C,N,V,H 1 SBIW Rdl,K Subtract Immediate from Word Rdh:Rdl ← Rdh:Rdl - K Z,C,N,V,S 2 AND Rd, Rr Logical AND Registers Rd ← Rd • Rr Z,N,V 1 ANDI Rd, K Logical AND Register and Constant Rd ← Rd • K Z,N,V 1 OR Rd, Rr Logical OR Registers Rd ← Rd v Rr Z,N,V 1 ORI Rd, K Logical OR Register and Constant Rd ← Rd v K Z,N,V 1 EOR Rd, Rr Exclusive OR Registers Rd ← Rd ⊕ Rr Z,N,V 1 COM Rd One’s Complement Rd ← 0xFF − Rd Z,C,N,V 1 NEG Rd Two’s Complement Rd ← 0x00 − Rd Z,C,N,V,H 1 SBR Rd,K Set Bit(s) in Register Rd ← Rd v K Z,N,V 1 CBR Rd,K Clear Bit(s) in Register Rd ← Rd • (0xFF - K) Z,N,V 1 INC Rd Increment Rd ← Rd + 1 Z,N,V 1 DEC Rd Decrement Rd ← Rd − 1 Z,N,V 1 TST Rd Test for Zero or Minus Rd ← Rd • Rd Z,N,V 1 CLR Rd Clear Register Rd ← Rd ⊕ Rd Z,N,V 1 SER Rd Set Register Rd ← 0xFF None 1 MUL Rd, Rr Multiply Unsigned R1:R0 ← Rd x Rr Z,C 2 MULS Rd, Rr Multiply Signed R1:R0 ← Rd x Rr Z,C 2 MULSU Rd, Rr Multiply Signed with Unsigned R1:R0 ← Rd x Rr Z,C 2 FMUL Rd, Rr Fractional Multiply Unsigned R1:R0 ← (Rd x Rr) << Z,C 2 FMULS Rd, Rr Fractional Multiply Signed Z,C 2 FMULSU Rd, Rr Fractional Multiply Signed with Unsigned Z,C 2 1 R1:R0 ← (Rd x Rr) << 1 R1:R0 ← (Rd x Rr) << 1 BRANCH INSTRUCTIONS RJMP k Relative Jump PC ← PC + k + 1 None 2 Indirect Jump to (Z) None 2 None 2 None 3 4 Extended Indirect Jump to (Z) PC ← Z PC ←(EIND:Z) JMP k Direct Jump PC ← k RCALL k IJMP EIJMP Relative Subroutine Call PC ← PC + k + 1 None ICALL Indirect Call to (Z) None 4 EICALL Extended Indirect Call to (Z) PC ← Z PC ←(EIND:Z) None 4 Direct Subroutine Call PC ← k None 5 RET Subroutine Return PC ← STACK None 5 RETI Interrupt Return PC ← STACK I Compare, Skip if Equal if (Rd = Rr) PC ← PC + 2 or 3 None CALL CPSE k Rd,Rr 5 1/2/3 CP Rd,Rr Compare Rd − Rr Z, N,V,C,H 1 CPC Rd,Rr Compare with Carry Rd − Rr − C Z, N,V,C,H 1 CPI Rd,K Compare Register with Immediate Rd − K Z, N,V,C,H SBRC Rr, b Skip if Bit in Register Cleared if (Rr(b)=0) PC ← PC + 2 or 3 None 1 1/2/3 SBRS Rr, b Skip if Bit in Register is Set if (Rr(b)=1) PC ← PC + 2 or 3 None 1/2/3 SBIC P, b Skip if Bit in I/O Register Cleared if (P(b)=0) PC ← PC + 2 or 3 None 1/2/3 1/2/3 SBIS P, b Skip if Bit in I/O Register is Set if (P(b)=1) PC ← PC + 2 or 3 None BRBS s, k Branch if Status Flag Set if (SREG(s) = 1) then PC←PC+k + 1 None 1/2 BRBC s, k Branch if Status Flag Cleared if (SREG(s) = 0) then PC←PC+k + 1 None 1/2 BREQ k Branch if Equal if (Z = 1) then PC ← PC + k + 1 None 1/2 BRNE k Branch if Not Equal if (Z = 0) then PC ← PC + k + 1 None 1/2 BRCS k Branch if Carry Set if (C = 1) then PC ← PC + k + 1 None 1/2 BRCC k Branch if Carry Cleared if (C = 0) then PC ← PC + k + 1 None 1/2 BRSH k Branch if Same or Higher if (C = 0) then PC ← PC + k + 1 None 1/2 BRLO k Branch if Lower if (C = 1) then PC ← PC + k + 1 None 1/2 BRMI k Branch if Minus if (N = 1) then PC ← PC + k + 1 None 1/2 BRPL k Branch if Plus if (N = 0) then PC ← PC + k + 1 None 1/2 1/2 BRGE k Branch if Greater or Equal, Signed if (N ⊕ V= 0) then PC ← PC + k + 1 None BRLT k Branch if Less Than Zero, Signed if (N ⊕ V= 1) then PC ← PC + k + 1 None 1/2 BRHS k Branch if Half Carry Flag Set if (H = 1) then PC ← PC + k + 1 None 1/2 1/2 BRHC k Branch if Half Carry Flag Cleared if (H = 0) then PC ← PC + k + 1 None BRTS k Branch if T Flag Set if (T = 1) then PC ← PC + k + 1 None 1/2 BRTC k Branch if T Flag Cleared if (T = 0) then PC ← PC + k + 1 None 1/2 15 2549KS–AVR–01/07 Mnemonics Operands Description Operation Flags #Clocks BRVS k Branch if Overflow Flag is Set if (V = 1) then PC ← PC + k + 1 None 1/2 BRVC k Branch if Overflow Flag is Cleared if (V = 0) then PC ← PC + k + 1 None 1/2 BRIE k Branch if Interrupt Enabled if ( I = 1) then PC ← PC + k + 1 None 1/2 BRID k Branch if Interrupt Disabled if ( I = 0) then PC ← PC + k + 1 None 1/2 BIT AND BIT-TEST INSTRUCTIONS SBI P,b Set Bit in I/O Register I/O(P,b) ← 1 None 2 CBI P,b Clear Bit in I/O Register I/O(P,b) ← 0 None 2 LSL Rd Logical Shift Left Rd(n+1) ← Rd(n), Rd(0) ← 0 Z,C,N,V 1 LSR Rd Logical Shift Right Rd(n) ← Rd(n+1), Rd(7) ← 0 Z,C,N,V 1 ROL Rd Rotate Left Through Carry Rd(0)←C,Rd(n+1)← Rd(n),C←Rd(7) Z,C,N,V 1 ROR Rd Rotate Right Through Carry Rd(7)←C,Rd(n)← Rd(n+1),C←Rd(0) Z,C,N,V 1 ASR Rd Arithmetic Shift Right Rd(n) ← Rd(n+1), n=0..6 Z,C,N,V 1 SWAP Rd Swap Nibbles Rd(3..0)←Rd(7..4),Rd(7..4)←Rd(3..0) None 1 BSET s Flag Set SREG(s) ← 1 SREG(s) 1 BCLR s Flag Clear SREG(s) ← 0 SREG(s) 1 BST Rr, b Bit Store from Register to T T ← Rr(b) T 1 BLD Rd, b Bit load from T to Register Rd(b) ← T None 1 SEC Set Carry C←1 C 1 CLC Clear Carry C←0 C 1 SEN Set Negative Flag N←1 N 1 CLN Clear Negative Flag N←0 N 1 SEZ Set Zero Flag Z←1 Z 1 CLZ Clear Zero Flag Z←0 Z 1 SEI Global Interrupt Enable I←1 I 1 CLI Global Interrupt Disable I←0 I 1 SES Set Signed Test Flag S←1 S 1 CLS Clear Signed Test Flag S←0 S 1 SEV Set Twos Complement Overflow. V←1 V 1 CLV Clear Twos Complement Overflow V←0 V 1 SET Set T in SREG T←1 T 1 CLT Clear T in SREG T←0 T 1 SEH CLH Set Half Carry Flag in SREG Clear Half Carry Flag in SREG H←1 H←0 H H 1 1 None 1 DATA TRANSFER INSTRUCTIONS MOV Rd, Rr Move Between Registers MOVW Rd, Rr Copy Register Word Rd ← Rr Rd+1:Rd ← Rr+1:Rr None 1 LDI Rd, K Load Immediate Rd ← K None 1 2 LD Rd, X Load Indirect Rd ← (X) None LD Rd, X+ Load Indirect and Post-Inc. Rd ← (X), X ← X + 1 None 2 LD Rd, - X Load Indirect and Pre-Dec. X ← X - 1, Rd ← (X) None 2 LD Rd, Y Load Indirect Rd ← (Y) None 2 LD Rd, Y+ Load Indirect and Post-Inc. Rd ← (Y), Y ← Y + 1 None 2 2 LD Rd, - Y Load Indirect and Pre-Dec. Y ← Y - 1, Rd ← (Y) None LDD Rd,Y+q Load Indirect with Displacement Rd ← (Y + q) None 2 LD Rd, Z Load Indirect Rd ← (Z) None 2 LD Rd, Z+ Load Indirect and Post-Inc. Rd ← (Z), Z ← Z+1 None 2 LD Rd, -Z Load Indirect and Pre-Dec. Z ← Z - 1, Rd ← (Z) None 2 2 LDD Rd, Z+q Load Indirect with Displacement Rd ← (Z + q) None LDS Rd, k Load Direct from SRAM Rd ← (k) None 2 ST X, Rr Store Indirect (X) ← Rr None 2 ST X+, Rr Store Indirect and Post-Inc. (X) ← Rr, X ← X + 1 None 2 ST - X, Rr Store Indirect and Pre-Dec. X ← X - 1, (X) ← Rr None 2 2 ST Y, Rr Store Indirect (Y) ← Rr None ST Y+, Rr Store Indirect and Post-Inc. (Y) ← Rr, Y ← Y + 1 None 2 ST - Y, Rr Store Indirect and Pre-Dec. Y ← Y - 1, (Y) ← Rr None 2 STD Y+q,Rr Store Indirect with Displacement (Y + q) ← Rr None 2 ST Z, Rr Store Indirect (Z) ← Rr None 2 ST Z+, Rr Store Indirect and Post-Inc. (Z) ← Rr, Z ← Z + 1 None 2 ST -Z, Rr Store Indirect and Pre-Dec. Z ← Z - 1, (Z) ← Rr None 2 STD Z+q,Rr Store Indirect with Displacement (Z + q) ← Rr None 2 STS k, Rr Store Direct to SRAM (k) ← Rr None 2 Load Program Memory R0 ← (Z) None 3 Load Program Memory Rd ← (Z) None 3 LPM LPM Rd, Z LPM Rd, Z+ ELPM ELPM 16 Rd, Z Load Program Memory and Post-Inc Rd ← (Z), Z ← Z+1 None 3 Extended Load Program Memory R0 ← (RAMPZ:Z) None 3 Extended Load Program Memory Rd ← (RAMPZ:Z) None 3 ATmega640/1280/1281/2560/2561 2549KS–AVR–01/07 ATmega640/1280/1281/2560/2561 Mnemonics ELPM Operands Rd, Z+ SPM Description Operation Flags #Clocks Extended Load Program Memory Rd ← (RAMPZ:Z), RAMPZ:Z ←RAMPZ:Z+1 None Store Program Memory (Z) ← R1:R0 None - Rd ← P None 1 3 IN Rd, P In Port OUT P, Rr Out Port P ← Rr None 1 PUSH Rr Push Register on Stack STACK ← Rr None 2 POP Rd Pop Register from Stack Rd ← STACK None 2 None 1 MCU CONTROL INSTRUCTIONS NOP No Operation SLEEP Sleep (see specific descr. for Sleep function) None 1 WDR BREAK Watchdog Reset Break (see specific descr. for WDR/timer) For On-chip Debug Only None None 1 N/A Note: EICALL and EIJMP do not exist in ATmega640/1280/1281. ELPM does not exist in ATmega640. 17 2549KS–AVR–01/07 Ordering Information ATmega640 Speed (MHz)(2) Power Supply 8 16 Notes: Ordering Code Package(1)(3) 1.8 - 5.5V ATmega640V-8AU ATmega640V-8CU 100A 100C1 Industrial (-40°C to 85°C) 2.7 - 5.5V ATmega640-16AU ATmega640-16CU 100A 100C1 Industrial (-40°C to 85°C) Operation Range 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information and minimum quantities. 2. See “Maximum speed vs. VCC” on page 377. 3. Pb-free packaging, complies to the European Directive for Restriction of Hazardous Substances (RoHS directive). Also Halide free and fully Green. Package Type 64A 64-lead, Thin (1.0 mm) Plastic Gull Wing Quad Flat Package (TQFP) 64M2 64-pad, 9 x 9 x 1.0 mm Body, Quad Flat No-lead/Micro Lead Frame Package (QFN/MLF) 100A 100-lead, Thin (1.0 mm) Plastic Gull Wing Quad Flat Package (TQFP) 100C1 100-ball, Chip Ball Grid Array (CBGA) 18 ATmega640/1280/1281/2560/2561 2549KS–AVR–01/07 ATmega640/1280/1281/2560/2561 ATmega1281 Speed (MHz)(2) Power Supply 8 16 Notes: Ordering Code Package(1)(3) Operation Range 1.8 - 5.5V ATmega1281V-8AU ATmega1281V-8MU 64A 64M2 Industrial (-40°C to 85°C) 2.7 - 5.5V ATmega1281-16AU ATmega1281-16MU 64A 64M2 Industrial (-40°C to 85°C) 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information and minimum quantities. 2. See “Maximum speed vs. VCC” on page 377. 3. Pb-free packaging, complies to the European Directive for Restriction of Hazardous Substances (RoHS directive). Also Halide free and fully Green. Package Type 64A 64-lead, Thin (1.0 mm) Plastic Gull Wing Quad Flat Package (TQFP) 64M2 64-pad, 9 x 9 x 1.0 mm Body, Quad Flat No-lead/Micro Lead Frame Package (QFN/MLF) 100A 100-lead, Thin (1.0 mm) Plastic Gull Wing Quad Flat Package (TQFP) 100C1 100-ball, Chip Ball Grid Array (CBGA) 19 2549KS–AVR–01/07 ATmega1280 Speed (MHz)(2) Power Supply 8 16 Notes: Ordering Code Package(1)(3) 1.8 - 5.5V ATmega1280V-8AU ATmega1280V-8CU 100A 100C1 Industrial (-40°C to 85°C) 2.7 - 5.5V ATmega1280-16AU ATmega1280-16AU 100A 100C1 Industrial (-40°C to 85°C) Operation Range 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information and minimum quantities. 2. See “Maximum speed vs. VCC” on page 377. 3. Pb-free packaging, complies to the European Directive for Restriction of Hazardous Substances (RoHS directive). Also Halide free and fully Green. Package Type 64A 64-lead, Thin (1.0 mm) Plastic Gull Wing Quad Flat Package (TQFP) 64M2 64-pad, 9 x 9 x 1.0 mm Body, Quad Flat No-lead/Micro Lead Frame Package (QFN/MLF) 100A 100-lead, Thin (1.0 mm) Plastic Gull Wing Quad Flat Package (TQFP) 100C1 100-ball, Chip Ball Grid Array (CBGA) 20 ATmega640/1280/1281/2560/2561 2549KS–AVR–01/07 ATmega640/1280/1281/2560/2561 ATmega2561 Speed (MHz)(2) Power Supply 8 16 Notes: Ordering Code Package(1)(3) Operation Range 1.8 - 5.5V ATmega2561V-8AU ATmega2561V-8MU 64A 64M2 Industrial (-40°C to 85°C) 4.5 - 5.5V ATmega2561-16AU ATmega2561-16MU 64A 64M2 Industrial (-40°C to 85°C) 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information and minimum quantities. 2. See “Maximum speed vs. VCC” on page 377. 3. Pb-free packaging, complies to the European Directive for Restriction of Hazardous Substances (RoHS directive). Also Halide free and fully Green. Package Type 64A 64-lead, Thin (1.0 mm) Plastic Gull Wing Quad Flat Package (TQFP) 64M2 64-pad, 9 x 9 x 1.0 mm Body, Quad Flat No-lead/Micro Lead Frame Package (QFN/MLF) 100A 100-lead, Thin (1.0 mm) Plastic Gull Wing Quad Flat Package (TQFP) 100C1 100-ball, Chip Ball Grid Array (CBGA) 21 2549KS–AVR–01/07 ATmega2560 Speed (MHz)(2) Power Supply 8 16 Notes: Ordering Code Package(1)(3) 1.8 - 5.5V ATmega2560V-8AU ATmega2560V-8CU 100A 100C1 Industrial (-40°C to 85°C) 4.5 - 5.5V ATmega2560-16AU ATmega2560-16CU 100A 100C1 Industrial (-40°C to 85°C) Operation Range 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information and minimum quantities. 2. See “Maximum speed vs. VCC” on page 377. 3. Pb-free packaging, complies to the European Directive for Restriction of Hazardous Substances (RoHS directive). Also Halide free and fully Green. Package Type 64A 64-lead, Thin (1.0 mm) Plastic Gull Wing Quad Flat Package (TQFP) 64M2 64-pad, 9 x 9 x 1.0 mm Body, Quad Flat No-lead/Micro Lead Frame Package (QFN/MLF) 100A 100-lead, Thin (1.0 mm) Plastic Gull Wing Quad Flat Package (TQFP) 100C1 100-ball, Chip Ball Grid Array (CBGA) 22 ATmega640/1280/1281/2560/2561 2549KS–AVR–01/07 ATmega640/1280/1281/2560/2561 Packaging Information 100A PIN 1 B PIN 1 IDENTIFIER E1 e E D1 D C 0˚~7˚ A1 A2 A L COMMON DIMENSIONS (Unit of Measure = mm) Notes: 1. This package conforms to JEDEC reference MS-026, Variation AED. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is 0.25 mm per side. Dimensions D1 and E1 are maximum plastic body size dimensions including mold mismatch. 3. Lead coplanarity is 0.08 mm maximum. SYMBOL MIN NOM MAX A – – 1.20 A1 0.05 – 0.15 A2 0.95 1.00 1.05 D 15.75 16.00 16.25 D1 13.90 14.00 14.10 E 15.75 16.00 16.25 E1 13.90 14.00 14.10 B 0.17 – 0.27 C 0.09 – 0.20 L 0.45 – 0.75 e NOTE Note 2 Note 2 0.50 TYP 10/5/2001 R 2325 Orchard Parkway San Jose, CA 95131 TITLE 100A, 100-lead, 14 x 14 mm Body Size, 1.0 mm Body Thickness, 0.5 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP) DRAWING NO. 100A REV. C 23 2549KS–AVR–01/07 100C1 0.12 Z E Marked A1 Identifier SIDE VIEW D A TOP VIEW A1 Øb e A1 Corner 0.90 TYP 10 9 8 7 6 5 4 3 2 1 A 0.90 TYP B C D COMMON DIMENSIONS (Unit of Measure = mm) E D1 F e SYMBOL MIN NOM MAX H A 1.10 – 1.20 I A1 0.30 0.35 0.40 D 8.90 9.00 9.10 E 8.90 9.00 9.10 G J E1 BOTTOM VIEW D1 7.10 7.20 7.30 E1 7.10 7.20 7.30 Øb 0.35 0.40 0.45 e NOTE 0.80 TYP 5/25/06 R 24 2325 Orchard Parkway San Jose, CA 95131 TITLE 100C1, 100-ball, 9 x 9 x 1.2 mm Body, Ball Pitch 0.80 mm Chip Array BGA Package (CBGA) DRAWING NO. 100C1 REV. A ATmega640/1280/1281/2560/2561 2549KS–AVR–01/07 ATmega640/1280/1281/2560/2561 64A PIN 1 B PIN 1 IDENTIFIER E1 e E D1 D C 0˚~7˚ A1 A2 A L COMMON DIMENSIONS (Unit of Measure = mm) Notes: 1. This package conforms to JEDEC reference MS-026, Variation AEB. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is 0.25 mm per side. Dimensions D1 and E1 are maximum plastic body size dimensions including mold mismatch. 3. Lead coplanarity is 0.10 mm maximum. SYMBOL MIN NOM MAX A – – 1.20 A1 0.05 – 0.15 A2 0.95 1.00 1.05 D 15.75 16.00 16.25 D1 13.90 14.00 14.10 E 15.75 16.00 16.25 E1 13.90 14.00 14.10 B 0.30 – 0.45 C 0.09 – 0.20 L 0.45 – 0.75 e NOTE Note 2 Note 2 0.80 TYP 10/5/2001 R 2325 Orchard Parkway San Jose, CA 95131 TITLE 64A, 64-lead, 14 x 14 mm Body Size, 1.0 mm Body Thickness, 0.8 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP) DRAWING NO. REV. 64A B 25 2549KS–AVR–01/07 64M2 D Marked Pin# 1 ID E C SEATING PLANE A1 TOP VIEW A K 0.08 C L Pin #1 Corner D2 1 2 3 SIDE VIEW Pin #1 Triangle Option A COMMON DIMENSIONS (Unit of Measure = mm) E2 Option B Pin #1 Chamfer (C 0.30) SYMBOL MIN NOM MAX A 0.80 0.90 1.00 – 0.02 0.05 0.18 0.25 0.30 A1 b K Option C b e Pin #1 Notch (0.20 R) BOTTOM VIEW D 8.90 9.00 9.10 D2 7.50 7.65 7.80 E 8.90 9.00 9.10 E2 7.50 7.65 7.80 e NOTE 0.50 BSC L 0.35 0.40 0.45 K 0.20 0.27 0.40 Note: 1. JEDEC Standard MO-220, (SAW Singulation) Fig. 1, VMMD. 2. Dimension and tolerance conform to ASMEY14.5M-1994. 5/25/06 R 26 TITLE 2325 Orchard Parkway 64M2, 64-pad, 9 x 9 x 1.0 mm Body, Lead Pitch 0.50 mm, San Jose, CA 95131 7.65 mm Exposed Pad, Micro Lead Frame Package (MLF) DRAWING NO. 64M2 REV. D ATmega640/1280/1281/2560/2561 2549KS–AVR–01/07 ATmega640/1280/1281/2560/2561 Errata ATmega640 rev. A • Inaccurate ADC conversion in differential mode with 200x gain • High current consumption in sleep mode 1. Inaccurate ADC conversion in differential mode with 200x gain With AVCC < 3.6V, random conversions will be inaccurate. Typical absolute accuracy may reach 64 LSB. Problem Fix/Workaround None 2. High current consumption in sleep mode. If a pending interrupt cannot wake the part up from the selected sleep mode, the current consumption will increase during sleep when executing the SLEEP instruction directly after a SEI instruction. Problem Fix/Workaround Before entering sleep, interrupts not used to wake the part from the sleep mode should be disabled. ATmega1280 rev. A • Inaccurate ADC conversion in differential mode with 200x gain • High current consumption in sleep mode 1. Inaccurate ADC conversion in differential mode with 200x gain With AVCC < 3.6V, random conversions will be inaccurate. Typical absolute accuracy may reach 64 LSB. Problem Fix/Workaround None 2. High current consumption in sleep mode. If a pending interrupt cannot wake the part up from the selected sleep mode, the current consumption will increase during sleep when executing the SLEEP instruction directly after a SEI instruction. Problem Fix/Workaround Before entering sleep, interrupts not used to wake the part from the sleep mode should be disabled. 27 2549KS–AVR–01/07 ATmega1281 rev. A • Inaccurate ADC conversion in differential mode with 200x gain • High current consumption in sleep mode 1. Inaccurate ADC conversion in differential mode with 200x gain With AVCC < 3.6V, random conversions will be inaccurate. Typical absolute accuracy may reach 64 LSB. Problem Fix/Workaround None 2. High current consumption in sleep mode. If a pending interrupt cannot wake the part up from the selected sleep mode, the current consumption will increase during sleep when executing the SLEEP instruction directly after a SEI instruction. Problem Fix/Workaround Before entering sleep, interrupts not used to wake the part from the sleep mode should be disabled. ATmega2560 rev. E No known errata. ATmega2560 rev. D Not sampled. ATmega2560 rev. C • High current consumption in sleep mode 1. High current consumption in sleep mode. If a pending interrupt cannot wake the part up from the selected sleep mode, the current consumption will increase during sleep when executing the SLEEP instruction directly after a SEI instruction. Problem Fix/Workaround Before entering sleep, interrupts not used to wake the part from the sleep mode should be disabled. ATmega2560 rev. B Not sampled. 28 ATmega640/1280/1281/2560/2561 2549KS–AVR–01/07 ATmega640/1280/1281/2560/2561 ATmega2560 rev. A • • • • • • 1. Non-Read-While-Write area of flash not functional Part does not work under 2.4 volts Incorrect ADC reading in differential mode Internal ADC reference has too low value IN/OUT instructions may be executed twice when Stack is in external RAM EEPROM read from application code does not work in Lock Bit Mode 3 Non-Read-While-Write area of flash not functional The Non-Read-While-Write area of the flash is not working as expected. The problem is related to the speed of the part when reading the flash of this area. Problem Fix/Workaround - Only use the first 248K of the flash. - If boot functionality is needed, run the code in the Non-Read-While-Write area at maximum 1/4th of the maximum frequency of the device at any given voltage. This is done by writing the CLKPR register before entering the boot section of the code 2. Part does not work under 2.4 volts The part does not execute code correctly below 2.4 volts Problem Fix/Workaround Do not use the part at voltages below 2.4 volts. 3. Incorrect ADC reading in differential mode The ADC has high noise in differential mode. It can give up to 7 LSB error. Problem Fix/Workaround Use only the 7 MSB of the result when using the ADC in differential mode. 4. Internal ADC reference has too low value The internal ADC reference has a value lower than specified Problem Fix/Workaround - Use AVCC or external reference - The actual value of the reference can be measured by applying a known voltage to the ADC when using the internal reference. The result when doing later conversions can then be calibrated. 5. IN/OUT instructions may be executed twice when Stack is in external RAM If either an IN or an OUT instruction is executed directly before an interrupt occurs and the stack pointer is located in external ram, the instruction will be executed twice. In some cases this will cause a problem, for example: - If reading SREG it will appear that the I-flag is cleared. - If writing to the PIN registers, the port will toggle twice. - If reading registers with interrupt flags, the flags will appear to be cleared. Problem Fix/Workaround There are two application work-arounds, where selecting one of them, will be omitting the issue: - Replace IN and OUT with LD/LDS/LDD and ST/STS/STD instructions - Use internal RAM for stack pointer. 29 2549KS–AVR–01/07 6. EEPROM read from application code does not work in Lock Bit Mode 3 When the Memory Lock Bits LB2 and LB1 are programmed to mode 3, EEPROM read does not work from the application code. Problem Fix/Workaround Do not set Lock Bit Protection Mode 3 when the application code needs to read from EEPROM. ATmega2561 rev. E No known errata. ATmega2561 rev. D Not sampled. ATmega2561 rev. C • High current consumption in sleep mode 1. High current consumption in sleep mode. If a pending interrupt cannot wake the part up from the selected sleep mode, the current consumption will increase during sleep when executing the SLEEP instruction directly after a SEI instruction. Problem Fix/Workaround Before entering sleep, interrupts not used to wake the part from the sleep mode should be disabled. ATmega2561 rev. B Not sampled. ATmega2561 rev. A • • • • • • 1. Non-Read-While-Write area of flash not functional Part does not work under 2.4 Volts Incorrect ADC reading in differential mode Internal ADC reference has too low value IN/OUT instructions may be executed twice when Stack is in external RAM EEPROM read from application code does not work in Lock Bit Mode 3 Non-Read-While-Write area of flash not functional The Non-Read-While-Write area of the flash is not working as expected. The problem is related to the speed of the part when reading the flash of this area. Problem Fix/Workaround - Only use the first 248K of the flash. - If boot functionality is needed, run the code in the Non-Read-While-Write area at maximum 1/4th of the maximum frequency of the device at any given voltage. This is done by writing the CLKPR register before entering the boot section of the code. 30 ATmega640/1280/1281/2560/2561 2549KS–AVR–01/07 ATmega640/1280/1281/2560/2561 2. Part does not work under 2.4 volts The part does not execute code correctly below 2.4 volts Problem Fix/Workaround Do not use the part at voltages below 2.4 volts. 3. Incorrect ADC reading in differential mode The ADC has high noise in differential mode. It can give up to 7 LSB error. Problem Fix/Workaround Use only the 7 MSB of the result when using the ADC in differential mode 4. Internal ADC reference has too low value The internal ADC reference has a value lower than specified Problem Fix/Workaround - Use AVCC or external reference - The actual value of the reference can be measured by applying a known voltage to the ADC when using the internal reference. The result when doing later conversions can then be calibrated. 5. IN/OUT instructions may be executed twice when Stack is in external RAM If either an IN or an OUT instruction is executed directly before an interrupt occurs and the stack pointer is located in external ram, the instruction will be executed twice. In some cases this will cause a problem, for example: - If reading SREG it will appear that the I-flag is cleared. - If writing to the PIN registers, the port will toggle twice. - If reading registers with interrupt flags, the flags will appear to be cleared. Problem Fix/Workaround There are two application workarounds, where selecting one of them, will be omitting the issue: - Replace IN and OUT with LD/LDS/LDD and ST/STS/STD instructions - Use internal RAM for stack pointer. 6. EEPROM read from application code does not work in Lock Bit Mode 3 When the Memory Lock Bits LB2 and LB1 are programmed to mode 3, EEPROM read does not work from the application code. Problem Fix/Workaround Do not set Lock Bit Protection Mode 3 when the application code needs to read from EEPROM. 31 2549KS–AVR–01/07 Datasheet Revision History Please note that the referring page numbers in this section are referring to this document.The referring revision in this section are referring to the document revision. Rev. 2549K-01/07 1. 2. 3. 4. 5. 6: 7. 8. 9. 10. Updated Table 1 on page 3. Updated “Pin Descriptions” on page 7. Updated “Stack Pointer” on page 14. Updated “Bit 1 – EEPE: EEPROM Programming Enable” on page 33. Updated Assembly code example in “Watchdog Timer” on page 62. Updated “EIMSK – External Interrupt Mask Register” on page 79. Updated Bit description in “PCIFR – Pin Change Interrupt Flag Register” on page 81. Updated code example in “USART Initialization” on page 215. Updated Figure 120 on page 288. Updated “DC Characteristics” on page 374. Rev. 2549J-09/06 1. 2. 3. 4. 5. 6. Updated “Calibrated Internal RC Oscillator” on page 44. Updated code example in “Moving Interrupts Between Application and Boot Section” on page 74. Updated “Timer/Counter Prescaler” on page 190. Updated “Device Identification Register” on page 309. Updated “Signature Bytes” on page 345. Updated “Instruction Set Summary” on page 421. Rev. 2549I-07/06 1. 2. Updated Table 74 on page 130, Table 77 on page 131, Table 79 on page 132, Table 82 on page 149, Table 84 on page 161, Table 85 on page 161, Table 89 on page 191, Table 92 on page 192 and Table 94 on page 193. Updated “Fast PWM Mode” on page 151. 1. 2. 3. Updated “Calibrated Internal RC Oscillator” on page 44. Updated “OSCCAL – Oscillator Calibration Register” on page 48. Added Table 172 on page 384. 1. 2. 3. 4. 5. 6. 7. Updated “Features” on page 1. Added Figure 2 on page 3, Table 1 on page 3. Updated “Calibrated Internal RC Oscillator” on page 44. Updated “Power Management and Sleep Modes” on page 50. Updated note for Table 30 on page 67. Updated Figure 121 on page 289 and Figure 122 on page 289. Updated “Setting the Boot Loader Lock Bits by SPM” on page 330. Rev. 2549H-06/06 Rev. 2549G-06/06 32 ATmega640/1280/1281/2560/2561 2549KS–AVR–01/07 ATmega640/1280/1281/2560/2561 8. 9. 10. Updated “Ordering Information” on page 18. Added Package information “100C1” on page 24. Updated “Errata” on page 27. 1. Updated Figure 15 on page 28, Figure 16 on page 29 and Figure 17 on page 29. Updated Table 88 on page 191 and Table 89 on page 191. Updated Features in “ADC – Analog to Digital Converter” on page 279. Updated “Fuse Bits” on page 343. Rev. 2549F-04/06 2. 3. 4. Rev. 2549E-04/06 1. 2. 3. 4. 5. 5. 6. Updated “Features” on page 1. Updated Table 27 on page 60. Updated note for Table 27 on page 60. Updated “Bit 6 – ACBG: Analog Comparator Bandgap Select” on page 277. Updated “Prescaling and Conversion Timing” on page 282. Updated “Maximum speed vs. VCC” on page 377. Updated “Ordering Information” on page 18. Rev. 2549D-12/05 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Advanced Information Status changed to Preliminary. Changed number of I/O Ports from 51 to 54. Updatet typos in “TCCR0A – Timer/Counter Control Register A” on page 130. Updated Features in “ADC – Analog to Digital Converter” on page 279. Updated Operation in“ADC – Analog to Digital Converter” on page 279 Updated Stabilizing Time in “Changing Channel or Reference Selection” on page 286. Updated Figure 113 on page 280, Figure 121 on page 289, Figure 122 on page 289. Updated Text in “ADCSRB – ADC Control and Status Register B” on page 295. Updated Note for Table 4 on page 41, Table 51 on page 99, Table 128 on page 294 and Table 131 on page 299. Updated Table 170 on page 382 and Table 171 on page 383. Updated “Filling the Temporary Buffer (Page Loading)” on page 329. Updated “Typical Characteristics” on page 390. Updated “Packaging Information” on page 23. Updated “Errata” on page 27. Rev. 2549C-09/05 1. 2. 3. Updated Speed Grade in section “Features” on page 1. Added “Resources” on page 9. Updated “SPI – Serial Peripheral Interface” on page 199. In Slave mode, low and high period SPI clock must be larger than 2 CPU cycles. 33 2549KS–AVR–01/07 4. 5. 6. 7. 8. Updated “Bit Rate Generator Unit” on page 251. Updated “Maximum speed vs. VCC” on page 377. Updated “Ordering Information” on page 18. Updated “Packaging Information” on page 23. Package 64M1 replaced by 64M2. Updated “Errata” on page 27. 1. 2. 3. 4. JTAG ID/Signature for ATmega640 updated: 0x9608. Updated Table 43 on page 94. Updated “Serial Programming Instruction set” on page 359. Updated “Errata” on page 27. 1. Initial version. Rev. 2549B-05/05 Rev. 2549A-03/05 34 ATmega640/1280/1281/2560/2561 2549KS–AVR–01/07 Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500 Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Atmel Operations Memory 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 RF/Automotive Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany Tel: (49) 71-31-67-0 Fax: (49) 71-31-67-2340 Microcontrollers 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France Tel: (33) 2-40-18-18-18 Fax: (33) 2-40-18-19-60 ASIC/ASSP/Smart Cards 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France Tel: (33) 4-76-58-30-00 Fax: (33) 4-76-58-34-80 Zone Industrielle 13106 Rousset Cedex, France Tel: (33) 4-42-53-60-00 Fax: (33) 4-42-53-60-01 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. © 2007 Atmel Corporation. All rights reserved. ATMEL ®, logo and combinations thereof, Everywhere You Are ®, AVR ®, AVR Studio ®, and others, are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. 2549KS–AVR–01/07