Product Folder Sample & Buy Support & Community Tools & Software Technical Documents LM4040A10, LM4040A20 SLOS456M – JANUARY 2005 – REVISED JANUARY 2015 LM4040xxx Precision Micropower Shunt Voltage Reference 1 Features 3 Description • The LM4040 series of shunt voltage references are versatile, easy-to-use references that cater to a vast array of applications. The 2-pin fixed-output device requires no external capacitors for operation and is stable with all capacitive loads. Additionally, the reference offers low dynamic impedance, low noise, and low temperature coefficient to ensure a stable output voltage over a wide range of operating currents and temperatures. The LM4040 uses fuse and Zener-zap reverse breakdown voltage trim during wafer sort to offer four output voltage tolerances, ranging from 0.1% (max) for the A grade to 1% (max) for the D grade. Thus, a great deal of flexibility is offered to designers in choosing the best cost-toperformance ratio for their applications. 1 • • • • • Fixed Output Voltages of 2.048 V, 2.5 V, 3 V, 4.096 V, 5 V, 8.192 V, and 10 V Tight Output Tolerances and Low Temperature Coefficient – Max 0.1%, 100 ppm/°C – A Grade – Max 0.2%, 100 ppm/°C – B Grade – Max 0.5%, 100 ppm/°C – C Grade – Max 1.0%, 150 ppm/°C – D Grade Low Output Noise: 35 μVRMS Typ Wide Operating Current Range: 45 μA Typ to 15 mA Stable With All Capacitive Loads; No Output Capacitor Required Available in Extended Temperature Range: –40°C to 125°C 2 Applications • • • • • • • • Data-Acquisition Systems Power Supplies and Power-Supply Monitors Instrumentation and Test Equipment Process Controls Precision Audio Automotive Electronics Energy Management Battery-Powered Equipment Packaged in space-saving SC-70 and SOT-23-3 packages and requiring a minimum current of 45 μA (typ), the LM4040 also is ideal for portable applications. The LM4040xI is characterized for operation over an ambient temperature range of –40°C to 85°C. The LM4040xQ is characterized for operation over an ambient temperature range of –40°C to 125°C. Device Information(1) PART NUMBER LM4040xxx PACKAGE (PIN) BODY SIZE (NOM) SOT-23 (3) 2.92 mm × 1.30 mm SC70 (6) 2.00 mm × 1.25 mm (1) For all available packages, see the orderable addendum at the end of the data sheet. 4 Simplified Schematic VS RS IZ + IL IL VZ IZ LM4040 1 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA. LM4040A10, LM4040A20 SLOS456M – JANUARY 2005 – REVISED JANUARY 2015 www.ti.com Table of Contents 1 2 3 4 5 6 7 Features .................................................................. Applications ........................................................... Description ............................................................. Simplified Schematic............................................. Revision History..................................................... Pin Configuration and Functions ......................... Specifications......................................................... Characteristics ......................................................... 7.17 LM4040C50I, LM4040D50I Electrical Characteristics ......................................................... 7.18 LM4040C50Q, LM4040D50Q Electrical Characteristics ......................................................... 7.19 LM4040A82I, LM4040B82I Electrical Characteristics ......................................................... 7.20 LM4040C82I, LM4040D82I Electrical Characteristics ......................................................... 7.21 LM4040A10I, LM4040B10I Electrical Characteristics ......................................................... 7.22 LM4040C10I, LM4040D10I Electrical Characteristics ......................................................... 7.23 Typical Characteristics .......................................... 1 1 1 1 2 4 5 7.1 7.2 7.3 7.4 7.5 Absolute Maximum Ratings ...................................... 5 ESD Ratings.............................................................. 5 Recommended Operating Conditions....................... 5 Thermal Information .................................................. 5 LM4040A20I, LM4040B20I Electrical Characteristics ........................................................... 6 7.6 LM4040C20I, LM4040D20I Electrical Characteristics ........................................................... 7 7.7 LM4040C20Q, LM4040D20Q Electrical Characteristics ........................................................... 8 7.8 LM4040A25I, LM4040B25I Electrical Characteristics ........................................................... 9 7.9 LM4040C25I, LM4040D25I Electrical Characteristics ......................................................... 10 7.10 LM4040C25Q, LM4040D25Q Electrical Characteristics ......................................................... 11 7.11 LM4040A30I, LM4040B30I Electrical Characteristics ......................................................... 12 7.12 LM4040C30I, LM4040D30I Electrical Characteristics ......................................................... 13 7.13 LM4040C30Q, LM4040D30Q Electrical Characteristics ......................................................... 14 7.14 LM4040A41I, LM4040B41I Electrical Characteristics ......................................................... 15 7.15 LM4040C41I, LM4040D41I Electrical Characteristics ......................................................... 16 7.16 LM4040A50I, LM4040B50I Electrical 8 18 19 20 21 22 23 24 Detailed Description ............................................ 25 8.1 8.2 8.3 8.4 9 17 Overview ................................................................. Functional Block Diagram ....................................... Feature Description................................................. Device Functional Modes........................................ 25 25 25 25 Applications and Implementation ...................... 26 9.1 Application Information............................................ 26 9.2 Typical Applications ................................................ 26 10 Power Supply Recommendations ..................... 29 11 Layout................................................................... 29 11.1 Layout Guidelines ................................................. 29 11.2 Layout Example .................................................... 29 12 Device and Documentation Support ................. 30 12.1 12.2 12.3 12.4 Related Links ........................................................ Trademarks ........................................................... Electrostatic Discharge Caution ............................ Glossary ................................................................ 30 30 30 30 13 Mechanical, Packaging, and Orderable Information ........................................................... 30 5 Revision History Changes from Revision L (January 2009) to Revision M Page • Added Applications, Device Information table, Pin Functions table, ESD Ratings table, Thermal Information table, Feature Description section, Device Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information section. ..................................................................................................................... 1 • Deleted Ordering Information table. ....................................................................................................................................... 1 2 Submit Documentation Feedback Copyright © 2005–2015, Texas Instruments Incorporated Product Folder Links: LM4040A10 LM4040A20 LM4040A10, LM4040A20 www.ti.com SLOS456M – JANUARY 2005 – REVISED JANUARY 2015 Table 1. Device Comparison Table (1) TA DEVICE GRADE 2.048 V LM4040A20I 2.5 V LM4040A25I 3V LM4040A30I 4.096 V LM4040A41I 5V LM4040A50I 8.192 V LM4040A82I 10 V LM4040A10I 2.048 V LM4040B20I 2.5 V LM4040B25I 3V LM4040B30I 4.096 V LM4040B41I 5V LM4040B50I 8.192 V LM4040B82I 10 V LM4040B10I 2.048 V LM4040C20I 2.5 V LM4040C25I 3V LM4040C30I 4.096 V LM4040C41I 5V LM4040C50I 8.192 V LM4040C82I 10 V LM4040C10I 2.048 V LM4040D20I 2.5 V LM4040D25I 3V LM4040D30I 4.096 V LM4040D41I 5V LM4040D50I 8.192 V LM4040D82I 10 V LM4040D10I C grade: 0.5% initial accuracy and 100 ppm/°C temperature coefficient 2.048 V LM4040C20Q 2.5 V LM4040C25Q 3V LM4040C30Q 5V LM4040C50Q D grade: 1.0% initial accuracy and 150 ppm/°C temperature coefficient 2.048 V LM4040D20Q 2.5 V LM4040D25Q 3V LM4040D30Q 5V LM4040D50Q A grade: 0.1% initial accuracy and 100 ppm/°C temperature coefficient –40°C to 85°C B grade: 0.2% initial accuracy and 100 ppm/°C temperature coefficient –40°C to 85°C –40°C to 85°C –40°C to 125°C (1) ORDERABLE PART NUMBER VKA C grade: 0.5% initial accuracy and 100 ppm/°C temperature coefficient D grade: 1.0% initial accuracy and 150 ppm/°C temperature coefficient For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI web site at www.ti.com. Copyright © 2005–2015, Texas Instruments Incorporated Product Folder Links: LM4040A10 LM4040A20 Submit Documentation Feedback 3 LM4040A10, LM4040A20 SLOS456M – JANUARY 2005 – REVISED JANUARY 2015 www.ti.com 6 Pin Configuration and Functions DBZ (SOT-23) PACKAGE (TOP VIEW) CATHODE 1 3* ANODE 2 * Pin 3 is attached to substrate and must be connected to ANODE or left open. DCK (SC-70) PACKAGE (TOP VIEW) ANODE NC CATHODE 1 5 NC 4 NC 2 3 NC – No internal connection Pin Functions PIN NAME TYPE DESCRIPTION DBZ DCK CATHODE 1 3 I/O Shunt Current/Voltage input ANODE 2 1 O Common pin, normally connected to ground NC — 2, 4, 5 I No Internal Connection * 3 — I Substrate Connection 4 Submit Documentation Feedback Copyright © 2005–2015, Texas Instruments Incorporated Product Folder Links: LM4040A10 LM4040A20 LM4040A10, LM4040A20 www.ti.com SLOS456M – JANUARY 2005 – REVISED JANUARY 2015 7 Specifications 7.1 Absolute Maximum Ratings over free-air temperature range (unless otherwise noted) (1) IZ Continuous cathode current TJ Operating virtual junction temperature Tstg Storage temperature range (1) MIN MAX –10 25 mA 150 °C 150 °C –65 UNIT Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditionsis not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 7.2 ESD Ratings VALUE V(ESD) (1) (2) Electrostatic discharge Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins (1) ±2000 Charged device model (CDM), per JEDEC specification JESD22-C101, all pins (2) ±1000 UNIT V JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process. 7.3 Recommended Operating Conditions IZ Cathode current TA Free-air temperature (1) MIN MAX (1) 15 LM4040xxxI –40 85 LM4040xxxQ –40 125 UNIT mA °C See parametric tables 7.4 Thermal Information LM4040xxx THERMAL METRIC (1) RθJA (1) Junction-to-ambient thermal resistance DBZ DCK 3 PINS 5 PINS 206 252 UNIT °C/W For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report (SPRA953). Copyright © 2005–2015, Texas Instruments Incorporated Product Folder Links: LM4040A10 LM4040A20 Submit Documentation Feedback 5 LM4040A10, LM4040A20 SLOS456M – JANUARY 2005 – REVISED JANUARY 2015 www.ti.com 7.5 LM4040A20I, LM4040B20I Electrical Characteristics at industrial temperature range, full-range TA = –40°C to 85°C (unless otherwise noted) PARAMETER VZ Reverse breakdown voltage ΔVZ Reverse breakdown voltage tolerance IZ,min Minimum cathode current TEST CONDITIONS IZ = 100 μA IZ = 100 μA IZ = 100 μA Reverse breakdown voltage change with cathode current change MIN 25°C TYP LM4040B20I MAX MIN 2.048 IZ,min < IZ < 1 mA 1 mA < IZ < 15 mA TYP MAX 2.048 –2 2 –4.1 4.1 Full range –15 15 –17 17 45 75 25°C ±20 25°C ±15 Full range ±15 25°C 0.3 75 80 mV μA ±20 ±15 ±100 25°C Full range 25°C 45 80 UNIT V 25°C 25°C Average temperature coefficient IZ = 1 mA of reverse breakdown voltage DVZ DI Z LM4040A20I Full range IZ = 10 mA αVZ TA ±100 ±15 0.8 0.3 1 2.5 Full range ppm/°C 6 0.8 1 2.5 8 6 mV 8 ZZ Reverse dynamic impedance IZ = 1 mA, f = 120 Hz, IAC = 0.1 IZ 25°C 0.3 eN Wideband noise IZ = 100 μA, 10 Hz ≤ f ≤ 10 kHz 25°C 35 35 μVRMS Long-term stability of reverse breakdown voltage t = 1000 h, TA = 25°C ± 0.1°C, IZ = 100 μA 120 120 ppm Thermal hysteresis (1) ΔTA = –40°C to 125°C 0.08% 0.08% VHYST (1) 6 0.8 0.3 0.8 Ω — Thermal hysteresis is defined as VZ,25°C (after cycling to –40°C) – VZ,25°C (after cycling to 125°C). Submit Documentation Feedback Copyright © 2005–2015, Texas Instruments Incorporated Product Folder Links: LM4040A10 LM4040A20 LM4040A10, LM4040A20 www.ti.com SLOS456M – JANUARY 2005 – REVISED JANUARY 2015 7.6 LM4040C20I, LM4040D20I Electrical Characteristics at industrial temperature range, full-range TA = –40°C to 85°C (unless otherwise noted) PARAMETER VZ Reverse breakdown voltage ΔVZ Reverse breakdown voltage tolerance IZ,min Minimum cathode current TEST CONDITIONS IZ = 100 μA IZ = 100 μA IZ = 100 μA Reverse breakdown voltage change with cathode current change MIN 25°C TYP LM4040D20I MAX MIN 2.048 IZ,min < IZ < 1 mA 1 mA < IZ < 15 mA TYP 2.048 V –10 10 –20 20 Full range –23 23 –40 40 45 75 ±20 25°C ±15 Full range ±15 25°C 0.3 mV 75 μA 80 ±20 ±15 ±100 25°C ±150 ppm/°C ±15 0.8 Full range 25°C 45 80 25°C UNIT MAX 25°C 25°C Average temperature coefficient IZ = 1 mA of reverse breakdown voltage DVZ DI Z LM4040C20I Full range IZ = 10 mA αVZ TA 0.3 1 2.5 6 Full range 1 1.2 2.5 8 8 mV 10 ZZ Reverse dynamic impedance IZ = 1 mA, f = 120 Hz, IAC = 0.1 IZ 25°C 0.3 eN Wideband noise IZ = 100 μA, 10 Hz ≤ f ≤ 10 kHz 25°C 35 35 μVRMS Long-term stability of reverse breakdown voltage t = 1000 h, TA = 25°C ± 0.1°C, IZ = 100 μA 120 120 ppm Thermal hysteresis (1) ΔTA = –40°C to 125°C 0.08% 0.08% VHYST (1) 0.9 0.3 1.1 Ω — Thermal hysteresis is defined as VZ,25°C (after cycling to –40°C) – VZ,25°C (after cycling to 125°C). Copyright © 2005–2015, Texas Instruments Incorporated Product Folder Links: LM4040A10 LM4040A20 Submit Documentation Feedback 7 LM4040A10, LM4040A20 SLOS456M – JANUARY 2005 – REVISED JANUARY 2015 www.ti.com 7.7 LM4040C20Q, LM4040D20Q Electrical Characteristics at extended temperature range, full-range TA = –40°C to 125°C (unless otherwise noted) PARAMETER VZ Reverse breakdown voltage ΔVZ Reverse breakdown voltage tolerance IZ,min Minimum cathode current TEST CONDITIONS IZ = 100 μA IZ = 100 μA IZ = 100 μA Reverse breakdown voltage change with cathode current change MIN 25°C TYP IZ,min < IZ < 1 mA 1 mA < IZ < 15 mA LM4040D20Q MAX MIN 2.048 TYP MAX 2.048 –10 10 –20 20 Full range –30 30 –50 50 45 75 25°C ±20 25°C ±15 Full range ±15 25°C 0.3 75 80 mV μA ±20 ±15 ±100 25°C Full range 25°C 45 80 UNIT V 25°C 25°C Average temperature coefficient IZ = 1 mA of reverse breakdown voltage DVZ DI Z LM4040C20Q Full range IZ = 10 mA αVZ TA ±150 ±15 0.8 0.3 1 2.5 Full range ppm/°C 6 1 1.2 2.5 8 8 mV 10 ZZ Reverse dynamic impedance IZ = 1 mA, f = 120 Hz, IAC = 0.1 IZ 25°C 0.3 eN Wideband noise IZ = 100 μA, 10 Hz ≤ f ≤ 10 kHz 25°C 35 35 μVRMS Long-term stability of reverse breakdown voltage t = 1000 h, TA = 25°C ± 0.1°C, IZ = 100 μA 120 120 ppm Thermal hysteresis (1) ΔTA = –40°C to 125°C 0.08% 0.08% VHYST (1) 8 0.9 0.3 1.1 Ω — Thermal hysteresis is defined as VZ,25°C (after cycling to –40°C) – VZ,25°C (after cycling to 125°C). Submit Documentation Feedback Copyright © 2005–2015, Texas Instruments Incorporated Product Folder Links: LM4040A10 LM4040A20 LM4040A10, LM4040A20 www.ti.com SLOS456M – JANUARY 2005 – REVISED JANUARY 2015 7.8 LM4040A25I, LM4040B25I Electrical Characteristics at industrial temperature range, full-range TA = –40°C to 85°C (unless otherwise noted) PARAMETER VZ Reverse breakdown voltage ΔVZ Reverse breakdown voltage tolerance IZ,min Minimum cathode current TEST CONDITIONS IZ = 100 μA IZ = 100 μA IZ = 100 μA Reverse breakdown voltage change with cathode current change MIN 25°C TYP LM4040B25I MAX MIN 2.5 IZ,min < IZ < 1 mA 1 mA < IZ < 15 mA TYP 2.5 V –2.5 2.5 –5 5 Full range –19 19 –21 21 45 75 ±20 25°C ±15 Full range ±15 25°C 0.3 mV 75 μA 80 ±20 ±15 ±100 25°C ±100 ppm/°C ±15 0.8 Full range 25°C 45 80 25°C UNIT MAX 25°C 25°C Average temperature coefficient IZ = 1 mA of reverse breakdown voltage DVZ DI Z LM4040A25I Full range IZ = 10 mA αVZ TA 0.3 1 2.5 6 Full range 0.8 1 2.5 8 6 mV 8 ZZ Reverse dynamic impedance IZ = 1 mA, f = 120 Hz, IAC = 0.1 IZ 25°C 0.3 eN Wideband noise IZ = 100 μA, 10 Hz ≤ f ≤ 10 kHz 25°C 35 35 μVRMS Long-term stability of reverse breakdown voltage t = 1000 h, TA = 25°C ± 0.1°C, IZ = 100 μA 120 120 ppm Thermal hysteresis (1) ΔTA = –40°C to 125°C 0.08% 0.08% VHYST (1) 0.8 0.3 0.8 Ω — Thermal hysteresis is defined as VZ,25°C (after cycling to –40°C) – VZ,25°C (after cycling to 125°C). Copyright © 2005–2015, Texas Instruments Incorporated Product Folder Links: LM4040A10 LM4040A20 Submit Documentation Feedback 9 LM4040A10, LM4040A20 SLOS456M – JANUARY 2005 – REVISED JANUARY 2015 www.ti.com 7.9 LM4040C25I, LM4040D25I Electrical Characteristics at industrial temperature range, full-range TA = –40°C to 85°C (unless otherwise noted) PARAMETER VZ Reverse breakdown voltage ΔVZ Reverse breakdown voltage tolerance IZ,min Minimum cathode current TEST CONDITIONS IZ = 100 μA IZ = 100 μA IZ = 100 μA Reverse breakdown voltage change with cathode current change MIN 25°C TYP LM4040D25I MAX MIN 2.5 IZ,min < IZ < 1 mA 1 mA < IZ < 15 mA TYP MAX 2.5 –12 12 –25 25 Full range –29 29 –49 49 45 75 25°C ±20 25°C ±15 Full range ±15 25°C 0.3 75 80 mV μA ±20 ±15 ±100 25°C Full range 25°C 45 80 UNIT V 25°C 25°C Average temperature coefficient IZ = 1 mA of reverse breakdown voltage DVZ DI Z LM4040C25I Full range IZ = 10 mA αVZ TA ±150 ±15 0.8 0.3 1 2.5 Full range ppm/°C 6 1 1.2 2.5 8 8 mV 10 ZZ Reverse dynamic impedance IZ = 1 mA, f = 120 Hz, IAC = 0.1 IZ 25°C 0.3 eN Wideband noise IZ = 100 μA, 10 Hz ≤ f ≤ 10 kHz 25°C 35 35 μVRMS Long-term stability of reverse breakdown voltage t = 1000 h, TA = 25°C ± 0.1°C, IZ = 100 μA 120 120 ppm Thermal hysteresis (1) ΔTA = –40°C to 125°C 0.08% 0.08% VHYST (1) 10 0.9 0.3 1.1 Ω — Thermal hysteresis is defined as VZ,25°C (after cycling to –40°C) – VZ,25°C (after cycling to 125°C). Submit Documentation Feedback Copyright © 2005–2015, Texas Instruments Incorporated Product Folder Links: LM4040A10 LM4040A20 LM4040A10, LM4040A20 www.ti.com SLOS456M – JANUARY 2005 – REVISED JANUARY 2015 7.10 LM4040C25Q, LM4040D25Q Electrical Characteristics at extended temperature range, full-range TA = –40°C to 125°C (unless otherwise noted) PARAMETER VZ Reverse breakdown voltage ΔVZ Reverse breakdown voltage tolerance IZ,min Minimum cathode current TEST CONDITIONS IZ = 100 μA IZ = 100 μA IZ = 100 μA Reverse breakdown voltage change with cathode current change MIN 25°C TYP IZ,min < IZ < 1 mA 1 mA < IZ < 15 mA LM4040D25Q MAX MIN 2.5 TYP 2.5 V –12 12 –25 25 Full range –38 38 –63 63 45 75 ±20 25°C ±15 Full range ±15 25°C 0.3 mV 75 μA 80 ±20 ±15 ±100 25°C ±150 ppm/°C ±15 0.8 Full range 25°C 45 80 25°C UNIT MAX 25°C 25°C Average temperature coefficient IZ = 1 mA of reverse breakdown voltage DVZ DI Z LM4040C25Q Full range IZ = 10 mA αVZ TA 0.3 1 2.5 6 Full range 1 1.2 2.5 8 8 mV 10 ZZ Reverse dynamic impedance IZ = 1 mA, f = 120 Hz, IAC = 0.1 IZ 25°C 0.3 eN Wideband noise IZ = 100 μA, 10 Hz ≤ f ≤ 10 kHz 25°C 35 35 μVRMS Long-term stability of reverse breakdown voltage t = 1000 h, TA = 25°C ± 0.1°C, IZ = 100 μA 120 120 ppm Thermal hysteresis (1) ΔTA = –40°C to 125°C 0.08% 0.08% VHYST (1) 0.9 0.3 1.1 Ω — Thermal hysteresis is defined as VZ,25°C (after cycling to –40°C) – VZ,25°C (after cycling to 125°C). Copyright © 2005–2015, Texas Instruments Incorporated Product Folder Links: LM4040A10 LM4040A20 Submit Documentation Feedback 11 LM4040A10, LM4040A20 SLOS456M – JANUARY 2005 – REVISED JANUARY 2015 www.ti.com 7.11 LM4040A30I, LM4040B30I Electrical Characteristics at industrial temperature range, full-range TA = –40°C to 85°C (unless otherwise noted) PARAMETER VZ Reverse breakdown voltage ΔVZ Reverse breakdown voltage tolerance IZ,min Minimum cathode current TEST CONDITIONS IZ = 100 μA IZ = 100 μA IZ = 100 μA Reverse breakdown voltage change with cathode current change MIN TYP 25°C LM4040B30I MAX MIN 3 IZ,min < IZ < 1 mA 1 mA < IZ < 15 mA TYP MAX 3 –3 3 –6 6 Full range –22 22 –26 26 47 77 25°C ±20 25°C ±15 Full range ±15 25°C 0.6 77 82 mV μA ±20 ±15 ±100 25°C Full range 25°C 47 82 UNIT V 25°C 25°C Average temperature coefficient IZ = 1 mA of reverse breakdown voltage DVZ DI Z LM4040A30I Full range IZ = 10 mA αVZ TA ±100 ±15 0.8 0.6 1.1 2.7 Full range ppm/°C 6 0.8 1.1 2.7 9 6 mV 9 ZZ Reverse dynamic impedance IZ = 1 mA, f = 120 Hz, IAC = 0.1 IZ 25°C 0.4 eN Wideband noise IZ = 100 μA, 10 Hz ≤ f ≤ 10 kHz 25°C 35 35 μVRMS Long-term stability of reverse breakdown voltage t = 1000 h, TA = 25°C ± 0.1°C, IZ = 100 μA 120 120 ppm Thermal hysteresis (1) ΔTA = –40°C to 125°C 0.08% 0.08% VHYST (1) 12 0.9 0.4 0.9 Ω — Thermal hysteresis is defined as VZ,25°C (after cycling to –40°C) – VZ,25°C (after cycling to 125°C). Submit Documentation Feedback Copyright © 2005–2015, Texas Instruments Incorporated Product Folder Links: LM4040A10 LM4040A20 LM4040A10, LM4040A20 www.ti.com SLOS456M – JANUARY 2005 – REVISED JANUARY 2015 7.12 LM4040C30I, LM4040D30I Electrical Characteristics at industrial temperature range, full-range TA = –40°C to 85°C (unless otherwise noted) PARAMETER VZ Reverse breakdown voltage ΔVZ Reverse breakdown voltage tolerance IZ,min Minimum cathode current TEST CONDITIONS IZ = 100 μA IZ = 100 μA IZ = 100 μA Reverse breakdown voltage change with cathode current change MIN TYP 25°C LM4040D30I MAX MIN 3 IZ,min < IZ < 1 mA 1 mA < IZ < 15 mA TYP 3 V –15 15 –30 30 Full range –34 34 –59 59 45 77 ±20 25°C ±15 Full range ±15 25°C 0.4 mV 77 μA 82 ±20 ±15 ±100 25°C ±150 ppm/°C ±15 0.8 Full range 25°C 45 82 25°C UNIT MAX 25°C 25°C Average temperature coefficient IZ = 1 mA of reverse breakdown voltage DVZ DI Z LM4040C30I Full range IZ = 10 mA αVZ TA 1.4 1.1 2.7 6 Full range 1 1.3 2.7 9 8 mV 11 ZZ Reverse dynamic impedance IZ = 1 mA, f = 120 Hz, IAC = 0.1 IZ 25°C 0.4 eN Wideband noise IZ = 100 μA, 10 Hz ≤ f ≤ 10 kHz 25°C 35 35 μVRMS Long-term stability of reverse breakdown voltage t = 1000 h, TA = 25°C ± 0.1°C, IZ = 100 μA 120 120 ppm Thermal hysteresis (1) ΔTA = –40°C to 125°C 0.08% 0.08% VHYST (1) 0.9 0.4 1.2 Ω — Thermal hysteresis is defined as VZ,25°C (after cycling to –40°C) – VZ,25°C (after cycling to 125°C). Copyright © 2005–2015, Texas Instruments Incorporated Product Folder Links: LM4040A10 LM4040A20 Submit Documentation Feedback 13 LM4040A10, LM4040A20 SLOS456M – JANUARY 2005 – REVISED JANUARY 2015 www.ti.com 7.13 LM4040C30Q, LM4040D30Q Electrical Characteristics at extended temperature range, full-range TA = –40°C to 125°C (unless otherwise noted) PARAMETER VZ Reverse breakdown voltage ΔVZ Reverse breakdown voltage tolerance IZ,min Minimum cathode current TEST CONDITIONS IZ = 100 μA IZ = 100 μA IZ = 100 μA Reverse breakdown voltage change with cathode current change MIN TYP 25°C IZ,min < IZ < 1 mA 1 mA < IZ < 15 mA LM4040D30Q MAX MIN 3 TYP MAX 3 –15 15 –30 30 Full range –45 45 –75 75 47 77 25°C ±20 25°C ±15 Full range ±15 25°C 0.4 77 82 mV μA ±20 ±15 ±100 25°C Full range 25°C 47 82 UNIT V 25°C 25°C Average temperature coefficient IZ = 1 mA of reverse breakdown voltage DVZ DI Z LM4040C30Q Full range IZ = 10 mA αVZ TA ±150 ±15 0.8 0.4 1.1 2.7 Full range ppm/°C 6 1.1 1.3 2.7 9 8 mV 11 ZZ Reverse dynamic impedance IZ = 1 mA, f = 120 Hz, IAC = 0.1 IZ 25°C 0.4 eN Wideband noise IZ = 100 μA, 10 Hz ≤ f ≤ 10 kHz 25°C 35 35 μVRMS Long-term stability of reverse breakdown voltage t = 1000 h, TA = 25°C ± 0.1°C, IZ = 100 μA 120 120 ppm Thermal hysteresis (1) ΔTA = –40°C to 125°C 0.08% 0.08% VHYST (1) 14 0.9 0.4 1.2 Ω — Thermal hysteresis is defined as VZ,25°C (after cycling to –40°C) – VZ,25°C (after cycling to 125°C). Submit Documentation Feedback Copyright © 2005–2015, Texas Instruments Incorporated Product Folder Links: LM4040A10 LM4040A20 LM4040A10, LM4040A20 www.ti.com SLOS456M – JANUARY 2005 – REVISED JANUARY 2015 7.14 LM4040A41I, LM4040B41I Electrical Characteristics at industrial temperature range, full-range TA = –40°C to 85°C (unless otherwise noted) PARAMETER VZ Reverse breakdown voltage ΔVZ Reverse breakdown voltage tolerance IZ,min Minimum cathode current TEST CONDITIONS IZ = 100 μA IZ = 100 μA IZ = 100 μA Reverse breakdown voltage change with cathode current change MIN 25°C TYP LM4040B41I MAX MIN 4.096 IZ,min < IZ < 1 mA 1 mA < IZ < 15 mA TYP 4.096 V –4.1 4.1 –8.2 8.2 Full range –31 31 –35 35 50 83 50 88 25°C ±30 25°C ±20 Full range ±20 25°C 0.5 83 μA ±30 ±20 ±100 ppm/°C ±20 0.9 Full range 0.5 1.2 25°C mV 88 ±100 25°C UNIT MAX 25°C 25°C Average temperature coefficient IZ = 1 mA of reverse breakdown voltage DVZ DI Z LM4040A41I Full range IZ = 10 mA αVZ TA 3 7 Full range 0.9 1.2 3 10 7 mV 10 ZZ Reverse dynamic impedance IZ = 1 mA, f = 120 Hz, IAC = 0.1 IZ 25°C 0.5 eN Wideband noise IZ = 100 μA, 10 Hz ≤ f ≤ 10 kHz 25°C 80 80 μVRMS Long-term stability of reverse breakdown voltage t = 1000 h, TA = 25°C ± 0.1°C, IZ = 100 μA 120 120 ppm Thermal hysteresis (1) ΔTA = –40°C to 125°C 0.08% 0.08% VHYST (1) 1 0.5 1 Ω — Thermal hysteresis is defined as VZ,25°C (after cycling to –40°C) – VZ,25°C (after cycling to 125°C). Copyright © 2005–2015, Texas Instruments Incorporated Product Folder Links: LM4040A10 LM4040A20 Submit Documentation Feedback 15 LM4040A10, LM4040A20 SLOS456M – JANUARY 2005 – REVISED JANUARY 2015 www.ti.com 7.15 LM4040C41I, LM4040D41I Electrical Characteristics at industrial temperature range, full-range TA = –40°C to 85°C (unless otherwise noted) PARAMETER VZ Reverse breakdown voltage ΔVZ Reverse breakdown voltage tolerance IZ,min Minimum cathode current TEST CONDITIONS IZ = 100 μA IZ = 100 μA IZ = 100 μA Reverse breakdown voltage change with cathode current change MIN 25°C TYP LM4040D41I MAX MIN 4.096 IZ,min < IZ < 1 mA 1 mA < IZ < 15 mA TYP MAX 4.096 –20 20 –41 41 Full range –47 47 –81 81 50 83 50 88 25°C ±30 25°C ±20 Full range ±20 25°C 0.5 mV μA ±30 ±20 Full range ±150 3 Full range ppm/°C ±20 0.9 0.5 1.2 25°C 83 88 ±100 25°C UNIT V 25°C 25°C Average temperature coefficient IZ = 1 mA of reverse breakdown voltage DVZ DI Z LM4040C41I Full range IZ = 10 mA αVZ TA 7 1.2 1.5 3 10 9 mV 13 ZZ Reverse dynamic impedance IZ = 1 mA, f = 120 Hz, IAC = 0.1 IZ 25°C 0.5 eN Wideband noise IZ = 100 μA, 10 Hz ≤ f ≤ 10 kHz 25°C 80 80 μVRMS Long-term stability of reverse breakdown voltage t = 1000 h, TA = 25°C ± 0.1°C, IZ = 100 μA 120 120 ppm Thermal hysteresis (1) ΔTA = –40°C to 125°C 0.08% 0.08% VHYST (1) 16 1 0.5 1.3 Ω — Thermal hysteresis is defined as VZ,25°C (after cycling to –40°C) – VZ,25°C (after cycling to 125°C). Submit Documentation Feedback Copyright © 2005–2015, Texas Instruments Incorporated Product Folder Links: LM4040A10 LM4040A20 LM4040A10, LM4040A20 www.ti.com SLOS456M – JANUARY 2005 – REVISED JANUARY 2015 7.16 LM4040A50I, LM4040B50I Electrical Characteristics at industrial temperature range, full-range TA = –40°C to 85°C (unless otherwise noted) PARAMETER VZ Reverse breakdown voltage ΔVZ Reverse breakdown voltage tolerance IZ,min Minimum cathode current TEST CONDITIONS IZ = 100 μA IZ = 100 μA IZ = 100 μA Reverse breakdown voltage change with cathode current change MIN TYP 25°C LM4040B50I MAX MIN 5 IZ,min < IZ < 1 mA 1 mA < IZ < 15 mA TYP 5 V –5 5 –10 10 Full range –38 38 –43 43 65 89 ±30 25°C ±20 Full range ±20 25°C 0.5 mV 89 μA 95 ±30 ±20 ±100 25°C ±100 ppm/°C ±20 1 Full range 25°C 65 95 25°C UNIT MAX 25°C 25°C Average temperature coefficient IZ = 1 mA of reverse breakdown voltage DVZ DI Z LM4040A50I Full range IZ = 10 mA αVZ TA 0.5 1.4 3.5 8 Full range 1 1.4 3.5 12 8 mV 12 ZZ Reverse dynamic impedance IZ = 1 mA, f = 120 Hz, IAC = 0.1 IZ 25°C 0.5 eN Wideband noise IZ = 100 μA, 10 Hz ≤ f ≤ 10 kHz 25°C 80 80 μVRMS Long-term stability of reverse breakdown voltage t = 1000 h, TA = 25°C ± 0.1°C, IZ = 100 μA 120 120 ppm Thermal hysteresis (1) ΔTA = –40°C to 125°C 0.08% 0.08% VHYST (1) 1.1 0.5 1.1 Ω — Thermal hysteresis is defined as VZ,25°C (after cycling to –40°C) – VZ,25°C (after cycling to 125°C). Copyright © 2005–2015, Texas Instruments Incorporated Product Folder Links: LM4040A10 LM4040A20 Submit Documentation Feedback 17 LM4040A10, LM4040A20 SLOS456M – JANUARY 2005 – REVISED JANUARY 2015 www.ti.com 7.17 LM4040C50I, LM4040D50I Electrical Characteristics at industrial temperature range, full-range TA = –40°C to 85°C (unless otherwise noted) PARAMETER VZ Reverse breakdown voltage ΔVZ Reverse breakdown voltage tolerance IZ,min Minimum cathode current TEST CONDITIONS IZ = 100 μA IZ = 100 μA IZ = 100 μA Reverse breakdown voltage change with cathode current change MIN TYP 25°C LM4040D50I MAX MIN 5 IZ,min < IZ < 1 mA 1 mA < IZ < 15 mA TYP MAX 5 –25 25 –50 50 Full range –58 58 –99 99 65 89 25°C ±30 25°C ±20 Full range ±20 25°C 0.5 89 95 mV μA ±30 ±20 ±100 25°C Full range 25°C 65 95 UNIT V 25°C 25°C Average temperature coefficient IZ = 1 mA of reverse breakdown voltage DVZ DI Z LM4040C50I Full range IZ = 10 mA αVZ TA ±150 ±20 1 0.5 1.4 3.5 Full range ppm/°C 8 1.3 1.8 3.5 12 10 mV 15 ZZ Reverse dynamic impedance IZ = 1 mA, f = 120 Hz, IAC = 0.1 IZ 25°C 0.5 eN Wideband noise IZ = 100 μA, 10 Hz ≤ f ≤ 10 kHz 25°C 80 80 μVRMS Long-term stability of reverse breakdown voltage t = 1000 h, TA = 25°C ± 0.1°C, IZ = 100 μA 120 120 ppm Thermal hysteresis (1) ΔTA = –40°C to 125°C 0.08% 0.08% VHYST (1) 18 1.1 0.5 1.5 Ω — Thermal hysteresis is defined as VZ,25°C (after cycling to –40°C) – VZ,25°C (after cycling to 125°C). Submit Documentation Feedback Copyright © 2005–2015, Texas Instruments Incorporated Product Folder Links: LM4040A10 LM4040A20 LM4040A10, LM4040A20 www.ti.com SLOS456M – JANUARY 2005 – REVISED JANUARY 2015 7.18 LM4040C50Q, LM4040D50Q Electrical Characteristics at extended temperature range, full-range TA = –40°C to 125°C (unless otherwise noted) PARAMETER VZ Reverse breakdown voltage ΔVZ Reverse breakdown voltage tolerance IZ,min Minimum cathode current TEST CONDITIONS IZ = 100 μA IZ = 100 μA IZ = 100 μA Reverse breakdown voltage change with cathode current change MIN TYP 25°C IZ,min < IZ < 1 mA 1 mA < IZ < 15 mA LM4040D50Q MAX MIN 5 TYP 5 V –25 25 –50 50 Full range –75 75 –125 125 65 89 ±30 25°C ±20 Full range ±20 25°C 0.5 mV 89 μA 95 ±30 ±20 ±100 25°C ±150 ppm/°C ±20 1 Full range 25°C 65 95 25°C UNIT MAX 25°C 25°C Average temperature coefficient IZ = 1 mA of reverse breakdown voltage DVZ DI Z LM4040C50Q Full range IZ = 10 mA αVZ TA 0.5 1.4 3.5 8 Full range 1 1.8 3.5 12 8 mV 12 ZZ Reverse dynamic impedance IZ = 1 mA, f = 120 Hz, IAC = 0.1 IZ 25°C 0.5 eN Wideband noise IZ = 100 μA, 10 Hz ≤ f ≤ 10 kHz 25°C 80 80 μVRMS Long-term stability of reverse breakdown voltage t = 1000 h, TA = 25°C ± 0.1°C, IZ = 100 μA 120 120 ppm Thermal hysteresis (1) ΔTA = –40°C to 125°C 0.08% 0.08% VHYST (1) 1.1 0.5 1.1 Ω — Thermal hysteresis is defined as VZ,25°C (after cycling to –40°C) – VZ,25°C (after cycling to 125°C). Copyright © 2005–2015, Texas Instruments Incorporated Product Folder Links: LM4040A10 LM4040A20 Submit Documentation Feedback 19 LM4040A10, LM4040A20 SLOS456M – JANUARY 2005 – REVISED JANUARY 2015 www.ti.com 7.19 LM4040A82I, LM4040B82I Electrical Characteristics at industrial temperature range, full-range TA = –40°C to 85°C (unless otherwise noted) PARAMETER VZ Reverse breakdown voltage ΔVZ Reverse breakdown voltage tolerance IZ,min Minimum cathode current TEST CONDITIONS IZ = 150 μA IZ = 150 μA IZ = 150 μA Reverse breakdown voltage change with cathode current change MIN 25°C TYP IZ,min < IZ < 1 mA 1 mA < IZ < 15 mA LM4040B82I MAX MIN 8.192 TYP MAX 8.192 –8.2 8.2 –16 16 Full range –61 61 –70 70 67 106 67 110 25°C ±40 25°C ±20 Full range ±20 25°C 0.6 mV μA ±40 ±20 Full range ±100 7 Full range ppm/°C ±20 1.3 0.6 2.5 25°C 106 110 ±100 25°C UNIT V 25°C 25°C Average temperature coefficient IZ = 1 mA of reverse breakdown voltage DVZ DI Z LM4040A82I Full range IZ = 10 mA αVZ TA 10 1.6 2.5 7 18 10 mV 18 ZZ Reverse dynamic impedance IZ = 1 mA, f = 120 Hz, IAC = 0.1 IZ 25°C 0.6 eN Wideband noise IZ = 150 μA, 10 Hz ≤ f ≤ 10 kHz 25°C 130 130 μVRMS Long-term stability of reverse breakdown voltage t = 1000 h, TA = 25°C ± 0.1°C, IZ = 150 μA 120 120 ppm Thermal hysteresis (1) ΔTA = –40°C to 125°C 0.08% 0.08% VHYST (1) 20 1.5 0.6 1.5 Ω — Thermal hysteresis is defined as VZ,25°C (after cycling to –40°C) – VZ,25°C (after cycling to 125°C). Submit Documentation Feedback Copyright © 2005–2015, Texas Instruments Incorporated Product Folder Links: LM4040A10 LM4040A20 LM4040A10, LM4040A20 www.ti.com SLOS456M – JANUARY 2005 – REVISED JANUARY 2015 7.20 LM4040C82I, LM4040D82I Electrical Characteristics at industrial temperature range, full-range TA = –40°C to 85°C (unless otherwise noted) PARAMETER VZ Reverse breakdown voltage ΔVZ Reverse breakdown voltage tolerance IZ,min Minimum cathode current TEST CONDITIONS IZ = 150 μA IZ = 150 μA IZ = 150 μA Reverse breakdown voltage change with cathode current change MIN 25°C TYP IZ,min < IZ < 1 mA 1 mA < IZ < 15 mA LM4040D82I MAX MIN 8.192 TYP 8.192 V –41 41 –82 82 Full range –94 94 –162 162 67 106 67 110 25°C ±40 25°C ±20 Full range ±20 25°C 0.6 111 μA ±40 ±20 ±150 ppm/°C ±20 1.3 Full range 0.6 1.7 7 15 2.5 25°C mV 115 ±100 25°C UNIT MAX 25°C 25°C Average temperature coefficient IZ = 1 mA of reverse breakdown voltage DVZ DI Z LM4040C82I Full range IZ = 10 mA αVZ TA 7 10 Full range 3 18 mV 24 ZZ Reverse dynamic impedance IZ = 1 mA, f = 120 Hz, IAC = 0.1 IZ 25°C 0.6 eN Wideband noise IZ = 150 μA, 10 Hz ≤ f ≤ 10 kHz 25°C 130 130 μVRMS Long-term stability of reverse breakdown voltage t = 1000 h, TA = 25°C ± 0.1°C, IZ = 150 μA 120 120 ppm Thermal hysteresis (1) ΔTA = –40°C to 125°C 0.08% 0.08% VHYST (1) 1.5 0.6 1.9 Ω — Thermal hysteresis is defined as VZ,25°C (after cycling to –40°C) – VZ,25°C (after cycling to 125°C). Copyright © 2005–2015, Texas Instruments Incorporated Product Folder Links: LM4040A10 LM4040A20 Submit Documentation Feedback 21 LM4040A10, LM4040A20 SLOS456M – JANUARY 2005 – REVISED JANUARY 2015 www.ti.com 7.21 LM4040A10I, LM4040B10I Electrical Characteristics at industrial temperature range, full-range TA = –40°C to 85°C (unless otherwise noted) PARAMETER VZ Reverse breakdown voltage ΔVZ Reverse breakdown voltage tolerance IZ,min Minimum cathode current TEST CONDITIONS IZ = 150 μA IZ = 150 μA IZ = 150 μA Reverse breakdown voltage change with cathode current change MIN 25°C TYP IZ,min < IZ < 1 mA 1 mA < IZ < 15 mA LM4040B10I MAX MIN 10 TYP MAX 10 –10 10 –20 20 Full range –75 75 –85 85 75 120 75 125 25°C ±40 25°C ±20 Full range ±20 25°C 0.8 mV μA ±40 ±20 Full range ±100 8 Full range ppm/°C ±20 1.5 0.8 3.5 25°C 120 125 ±100 25°C UNIT V 25°C 25°C Average temperature coefficient IZ = 1 mA of reverse breakdown voltage DVZ DI Z LM4040A10I Full range IZ = 10 mA αVZ TA 14 1.5 3.5 8 24 14 mV 24 ZZ Reverse dynamic impedance IZ = 1 mA, f = 120 Hz, IAC = 0.1 IZ 25°C 0.7 eN Wideband noise IZ = 150 μA, 10 Hz ≤ f ≤ 10 kHz 25°C 180 180 μVRMS Long-term stability of reverse breakdown voltage t = 1000 h, TA = 25°C ± 0.1°C, IZ = 150 μA 120 120 ppm Thermal hysteresis (1) ΔTA = –40°C to 125°C 0.08% 0.08% VHYST (1) 22 1.7 0.7 1.7 Ω — Thermal hysteresis is defined as VZ,25°C (after cycling to –40°C) – VZ,25°C (after cycling to 125°C). Submit Documentation Feedback Copyright © 2005–2015, Texas Instruments Incorporated Product Folder Links: LM4040A10 LM4040A20 LM4040A10, LM4040A20 www.ti.com SLOS456M – JANUARY 2005 – REVISED JANUARY 2015 7.22 LM4040C10I, LM4040D10I Electrical Characteristics at industrial temperature range, full-range TA = –40°C to 85°C (unless otherwise noted) PARAMETER VZ Reverse breakdown voltage ΔVZ Reverse breakdown voltage tolerance IZ,min Minimum cathode current TEST CONDITIONS IZ = 150 μA IZ = 150 μA IZ = 150 μA Reverse breakdown voltage change with cathode current change MIN 25°C TYP IZ,min < IZ < 1 mA 1 mA < IZ < 15 mA LM4040D10I MAX MIN 10 TYP 10 V –50 50 –100 100 Full range –115 115 –198 198 75 120 75 125 25°C ±40 25°C ±20 Full range ±20 25°C 0.8 130 μA ±40 ±20 ±150 ppm/°C ±20 1.5 Full range 0.8 2 8 18 3.5 25°C mV 135 ±100 25°C UNIT MAX 25°C 25°C Average temperature coefficient IZ = 1 mA of reverse breakdown voltage DVZ DI Z LM4040C10I Full range IZ = 10 mA αVZ TA 8 14 Full range 4 24 mV 29 ZZ Reverse dynamic impedance IZ = 1 mA, f = 120 Hz, IAC = 0.1 IZ 25°C 0.7 eN Wideband noise IZ = 150 μA, 10 Hz ≤ f ≤ 10 kHz 25°C 180 180 μVRMS Long-term stability of reverse breakdown voltage t = 1000 h, TA = 25°C ± 0.1°C, IZ = 150 μA 120 120 ppm Thermal hysteresis (1) ΔTA = –40°C to 125°C 0.08% 0.08% VHYST (1) 1.7 0.7 2.3 Ω — Thermal hysteresis is defined as VZ,25°C (after cycling to –40°C) – VZ,25°C (after cycling to 125°C). Copyright © 2005–2015, Texas Instruments Incorporated Product Folder Links: LM4040A10 LM4040A20 Submit Documentation Feedback 23 LM4040A10, LM4040A20 SLOS456M – JANUARY 2005 – REVISED JANUARY 2015 www.ti.com 7.23 Typical Characteristics 0.5 VZ, Change (%) 0.4 0.3 0.2 0.1 ZZ, Dynamic Output Impedance (Ω) 0.6 VZ = 2.5 V IZ = 150 mA 50 ppm/°C 20 ppm/°C 7 ppm/°C 0 −0.1 −0.2 −0.3 −0.4 20 40 60 80 100 120 Temperature (°C) Figure 1. Temperature Drift for Different Average Temperature Coefficients −20 0 No Capacitor 1 µF Tantanlum Capacitor 10 VZ = 2.5 V IZ = 150 µA TJ = 25°C IZ,AC = 0.1 IZ 1 0.1 100 XC 1k 120 1000 No Capacitor 100 VZ = 2.5 V IZ = 1 mA TJ = 25°C IZ,AC = 0.1 IZ 10 1-mF Tantanlum Capacitor 1 0.1 100 XC 10k 100k 1M Frequency (Hz) Figure 3. Output Impedance vs Frequency 1k Noise (mV/eHz) 10 Submit Documentation Feedback VZ = 2.5 V TJ = 25°C 100 80 60 40 20 0 0 0.5 1 1.5 2 2.5 3 VZ, Reverse Voltage (V) Figure 4. Temperature Drift for Different Average Temperature Coefficient VZ = 2.5 V IZ = 200 mA TJ = 25°C 1 0.1 24 100 10k 100k 1M Frequency (Hz) Figure 2. Output Impedance vs Frequency IZ, Cathode Current (mA) ZZ, Dynamic Output Impedance (W) −40 1000 1 100 1k 10k Frequency (Hz) Figure 5. Noise Voltage vs Frequency 10 100k Copyright © 2005–2015, Texas Instruments Incorporated Product Folder Links: LM4040A10 LM4040A20 LM4040A10, LM4040A20 www.ti.com SLOS456M – JANUARY 2005 – REVISED JANUARY 2015 8 Detailed Description 8.1 Overview The LM4040 is a precision micro-power curvature-corrected bandgap shunt voltage reference. The LM4040 has been designed for stable operation without the need of an external capacitor connected between the “+” pin and the “−” pin. If, however, a bypass capacitor is used, the LM4040 remains stable. LM4040 offers several fixed reverse breakdown voltages: 2.048 V, 2.500 V, 3.000 V, 4.096 V, 5.000 V, 6.000, 8.192 V, and 10.000 V. The minimum operating current increases from 60 µA for the LM4040-N-2.048 and LM4040-N-2.5 to 100 μA for the 10.0-V LM4040. All versions have a maximum operating current of 15 mA. Each reverse voltage options can be purchased with initial tolerances (at 25°C) of 0.1%, 0.2%, 0.5% and 1.0%. These reference options are denoted by A (0.1%), B (0.2%), C (0.5%) and D for (1.0%). The LM4040xxxI devices are characterized for operation from –40°C to 85°C, and the LM4040xxxQ devices are characterized for operation from –40°C to 125°C. 8.2 Functional Block Diagram CATHODE + _ ANODE 8.3 Feature Description A temperature compensated band gap voltage reference controls high gain amplifier and shunt pass element to maintain a nearly constant voltage between cathode and anode. Regulation occurs after a minimum current is provided to power the voltage divider and amplifier. Internal frequency compensation provides a stable loop for all capacitor loads. Floating shunt design is useful for both positive and negative regulation applications. 8.4 Device Functional Modes 8.4.1 Shunt Reference LM4040x will operate in one mode, which is as a fixed voltage reference that cannot be adjusted. LM4040x does offer various Reverse Voltage options that have unique electrical characteristics detailed in the Specifications section. In order for a proper Reverse Voltage to be developed, current must be sourced into the cathode of LM4040x. The minimum current needed for proper regulation is denoted in the Specifications section as IZ,min. Copyright © 2005–2015, Texas Instruments Incorporated Product Folder Links: LM4040A10 LM4040A20 Submit Documentation Feedback 25 LM4040A10, LM4040A20 SLOS456M – JANUARY 2005 – REVISED JANUARY 2015 www.ti.com 9 Applications and Implementation NOTE Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI’s customers are responsible for determining suitability of components for their purposes. Customers should validate and test their design implementation to confirm system functionality. 9.1 Application Information LM4040xxx is a well known industry standard device used in several applications and end equipment where a reference is required. Below describes this device being used in a data acquisition system. Analog to Digital conversion systems are the most common applications to use LM4040x due to its low reference tolerance which allows high precision in these systems. 9.2 Typical Applications ADS7842 0 V to VREF 1 AIN0 5V 2 AIN1 909 + 2.2 mF VDIG 28 + 27 3 AIN2 A1 26 4 AIN3 A0 25 5 VREF CLK 24 0.1 mF 5-V Analog Supply + 10 mF 3.2-MHz Clock BUSY 23 BUSY Output 7 DB11 WR 22 Write Input 8 DB10 CS 21 9 DB9 RD 20 6 AGND LM4040A-41 VANA 10 DB8 DB0 19 11 DB7 DB1 18 12 DB6 DB2 17 13 DB5 DB3 16 14 DGND DB4 15 Read Input Figure 6. Data-Acquisition Circuit With LM4040x-41 9.2.1 Design Requirements For this design example, use the parameters listed in Table 2 as the input parameters. Table 2. Design Parameters DESIGN PARAMETER 26 EXAMPLE VALUE ADC FSR (Full Scale Range) 4.096 ADC Resolution 12 Bits Supply Voltage 5V Cathode Current (Ik) 100 µA Submit Documentation Feedback Copyright © 2005–2015, Texas Instruments Incorporated Product Folder Links: LM4040A10 LM4040A20 LM4040A10, LM4040A20 www.ti.com SLOS456M – JANUARY 2005 – REVISED JANUARY 2015 9.2.2 Detailed Design Procedure When using LM4040x as a comparator with reference, determine the following: • Input voltage range • Reference voltage accuracy • Output logic input high and low level thresholds • Current source resistance 9.2.2.1 LM4040x Voltage and Accuracy Choice When using LM4040x as a reference for an ADC, the ADC's FSR (Full Scale Range), Resolution and LSB must be determined. LSB can be determined by: LSB=FSR/(2N-1) With N being the resolution or Number of Bits. FSR and Resolution can be determined by the ADC's datasheet. Vref can be determined by: Vref=FSR+LSB Though modern data converters use calibration techniques to compensate for any error introduced by a Vref's inaccuracy, it is best to use the highest accuracy available. This is due to errors in the calibration method that may allow some non-linearities introduced by the Vref's initial accuracy. A good example is the LM4040x-41 that is designed to be a cost-effective voltage reference as required in 12-bit data-acquisition systems. For 12-bit systems operating from 5-V supplies (see Figure 6), the LM4040A-41 (4.096 V, 0.01%) only introduces 4 LSBs (4mV) of possible error in a system that consists of 4096 LSBs. 9.2.2.2 Cathode and Load Currents In a typical shunt-regulator configuration (see Figure 7), an external resistor, RS, is connected between the supply and the cathode of the LM4040. RS must be set properly, as it sets the total current available to supply the load (IL) and bias the LM4040 (IZ). In all cases, IZ must stay within a specified range for proper operation of the reference. Taking into consideration one extreme in the variation of the load and supply voltage (maximum IL and minimum VS), RS must be small enough to supply the minimum IZ required for operation of the regulator, as given by data-sheet parameters. At the other extreme, maximum VS and minimum IL, RS must be large enough to limit IZ to less than its maximum-rated value of 15 mA. RS is calculated according to Equation 1: (V - VZ ) RS = S (IL + IZ ) (1) VS RS IZ + IL IL VZ IZ LM4040 Figure 7. Shunt Regulator 9.2.2.3 Output Capacitor The LM4040 does not require an output capacitor across cathode and anode for stability. However, if an output bypass capacitor is desired, the LM4040 is designed to be stable with all capacitive loads. Copyright © 2005–2015, Texas Instruments Incorporated Product Folder Links: LM4040A10 LM4040A20 Submit Documentation Feedback 27 LM4040A10, LM4040A20 SLOS456M – JANUARY 2005 – REVISED JANUARY 2015 www.ti.com 9.2.2.4 SOT-23 Connections There is a parasitic Schottky diode connected between pins 2 and 3 of the SOT-23 packaged device. Thus, pin 3 of the SOT-23 package must be left floating or connected to pin 2. 9.2.2.5 Start-Up Characteristics In any data conversion system, start-up characteristics are important, as to determine when it is safe begin conversion based upon a steady and settled reference value. As shown in Figure 9 it is best to allow for >20µs from supply start-up to begin conversion. RS VIN LM4040 VZ 1 Hz Rate Figure 8. Test Circuit 9.2.3 Application Curves 6 6 4 VZ = 2.5 V TJ = 25°C RS = 30 kW VZ (V) 4 2 VIN 0 3 −2 −4 2 VZ VIN (V) 5 −6 1 −8 0 −10 −1 −10 −12 0 10 20 30 40 50 60 70 80 90 Response Time (ms) Figure 9. Startup Response 28 Submit Documentation Feedback Copyright © 2005–2015, Texas Instruments Incorporated Product Folder Links: LM4040A10 LM4040A20 LM4040A10, LM4040A20 www.ti.com SLOS456M – JANUARY 2005 – REVISED JANUARY 2015 10 Power Supply Recommendations In order to not exceed the maximum cathode current, be sure that the supply voltage is current limited. For applications shunting high currents (15 mA max), pay attention to the cathode and anode trace lengths, adjusting the width of the traces to have the proper current density. 11 Layout 11.1 Layout Guidelines Figure 10 shows an example of a PCB layout of LM4040XXXDBZ. Some key Vref noise considerations are: • Connect a low-ESR, 0.1-μF (CL) ceramic bypass capacitor on the cathode pin node. • Decouple other active devices in the system per the device specifications. • Using a solid ground plane helps distribute heat and reduces electromagnetic interference (EMI) noise pickup. • Place the external components as close to the device as possible. This configuration prevents parasitic errors (such as the Seebeck effect) from occurring. • Do not run sensitive analog traces in parallel with digital traces. Avoid crossing digital and analog traces if possible and only make perpendicular crossings when absolutely necessary. 11.2 Layout Example GND DBZ (TOP VIEW) CL Rsup Vsup CATHODE GND ANODE 1 3 2 Figure 10. DBZ Layout example Copyright © 2005–2015, Texas Instruments Incorporated Product Folder Links: LM4040A10 LM4040A20 Submit Documentation Feedback 29 LM4040A10, LM4040A20 SLOS456M – JANUARY 2005 – REVISED JANUARY 2015 www.ti.com 12 Device and Documentation Support 12.1 Related Links The table below lists quick access links. Categories include technical documents, support and community resources, tools and software, and quick access to sample or buy. Table 3. Related Links PARTS PRODUCT FOLDER SAMPLE & BUY TECHNICAL DOCUMENTS TOOLS & SOFTWARE SUPPORT & COMMUNITY LM4040A10 Click here Click here Click here Click here Click here LM4040A20 Click here Click here Click here Click here Click here 12.2 Trademarks All trademarks are the property of their respective owners. 12.3 Electrostatic Discharge Caution These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 12.4 Glossary SLYZ022 — TI Glossary. This glossary lists and explains terms, acronyms, and definitions. 13 Mechanical, Packaging, and Orderable Information The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation. 30 Submit Documentation Feedback Copyright © 2005–2015, Texas Instruments Incorporated Product Folder Links: LM4040A10 LM4040A20 PACKAGE OPTION ADDENDUM www.ti.com 25-Nov-2015 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) LM4040A10IDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4NQ3 ~ 4NQU) LM4040A10IDBZRG4 ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4NQ3 ~ 4NQU) LM4040A10IDBZT ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4NQ3 ~ 4NQU) LM4040A10IDCKR ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 PHU LM4040A10ILP PREVIEW TO-92 LP 3 1000 TBD Call TI Call TI -40 to 85 LM4040A10ILPR PREVIEW TO-92 LP 3 2000 TBD Call TI Call TI -40 to 85 LM4040A20IDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4MC3 ~ 4MCU) LM4040A20IDBZRG4 ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4MC3 ~ 4MCU) LM4040A20IDBZT ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4MC3 ~ 4MCU) LM4040A20IDBZTG4 ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4MC3 ~ 4MCU) LM4040A20IDCKR ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 MSU LM4040A20IDCKRE4 ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 MSU LM4040A25IDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4NG3 ~ 4NGU) LM4040A25IDBZT ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4NG3 ~ 4NGU) LM4040A25IDBZTG4 ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4NG3 ~ 4NGU) LM4040A25IDCKR ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 P2U LM4040A25ILP PREVIEW TO-92 LP 3 1000 TBD Call TI Call TI -40 to 85 LM4040A25ILPR PREVIEW TO-92 LP 3 2000 TBD Call TI Call TI -40 to 85 LM4040A30IDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 Addendum-Page 1 (4M63 ~ 4M6U) Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 25-Nov-2015 Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) LM4040A30IDBZRG4 ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4M63 ~ 4M6U) LM4040A30IDBZT ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4M63 ~ 4M6U) LM4040A30IDBZTG4 ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4M63 ~ 4M6U) LM4040A30IDCKR ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 P9U LM4040A30IDCKRE4 ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 P9U LM4040A30IDCKT PREVIEW SC70 DCK 5 250 TBD Call TI Call TI -40 to 85 LM4040A30ILP PREVIEW TO-92 LP 3 1000 TBD Call TI Call TI -40 to 85 LM4040A30ILPM PREVIEW TO-92 LP 3 2000 TBD Call TI Call TI -40 to 85 LM4040A30ILPR PREVIEW TO-92 LP 3 2000 TBD Call TI Call TI -40 to 85 LM4040A41IDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4M23 ~ 4M2U) LM4040A41IDBZRG4 ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4M23 ~ 4M2U) LM4040A41IDBZT ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4M23 ~ 4M2U) LM4040A41IDBZTG4 ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4M23 ~ 4M2U) LM4040A41IDCKR ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 P4U LM4040A41ILP PREVIEW TO-92 LP 3 1000 TBD Call TI Call TI -40 to 85 LM4040A41ILPR PREVIEW TO-92 LP 3 2000 TBD Call TI Call TI -40 to 85 LM4040A50IDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4NA3 ~ 4NAU) LM4040A50IDBZT ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4NA3 ~ 4NAU) LM4040A50IDBZTG4 ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4NA3 ~ 4NAU) LM4040A50IDCKR ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 N5U Addendum-Page 2 Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 25-Nov-2015 Status (1) LM4040A50IDCKRG4 ACTIVE Package Type Package Pins Package Drawing Qty SC70 DCK 5 3000 Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 Device Marking (4/5) N5U LM4040A50ILP PREVIEW TO-92 LP 3 1000 TBD Call TI Call TI -40 to 85 LM4040A82IDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4NL3 ~ 4NLU) LM4040A82IDBZT ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4NL3 ~ 4NLU) LM4040A82IDBZTG4 ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4NL3 ~ 4NLU) LM4040A82IDCKR ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 PDU LM4040B10IDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4NR3 ~ 4NRU) LM4040B10IDBZT ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4NR3 ~ 4NRU) LM4040B10IDBZTG4 ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4NR3 ~ 4NRU) LM4040B10IDCKR ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 PJU LM4040B10ILP PREVIEW TO-92 LP 3 1000 TBD Call TI Call TI -40 to 85 LM4040B10ILPR PREVIEW TO-92 LP 3 2000 TBD Call TI Call TI -40 to 85 LM4040B20IDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4MD3 ~ 4MDU) LM4040B20IDBZRG4 ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4MD3 ~ 4MDU) LM4040B20IDBZT ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4MD3 ~ 4MDU) LM4040B20IDBZTG4 ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4MD3 ~ 4MDU) LM4040B20IDCKR ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 MTU LM4040B25IDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4NH3 ~ 4NHU) LM4040B25IDBZRG4 ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4NH3 ~ 4NHU) Addendum-Page 3 Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 25-Nov-2015 Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) LM4040B25IDBZT ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4NH3 ~ 4NHU) LM4040B25IDBZTG4 ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4NH3 ~ 4NHU) LM4040B25IDCKR ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 P3U LM4040B25IDCKRG4 ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 P3U LM4040B25ILP PREVIEW TO-92 LP 3 1000 TBD Call TI Call TI -40 to 85 LM4040B25ILPR PREVIEW TO-92 LP 3 2000 TBD Call TI Call TI -40 to 85 LM4040B30IDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4M73 ~ 4M7U) LM4040B30IDBZRG4 ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4M73 ~ 4M7U) LM4040B30IDBZT ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4M73 ~ 4M7U) LM4040B30IDCKR ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 PAU LM4040B30IDCKRG4 ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 PAU LM4040B30IDCKT PREVIEW SC70 DCK 5 250 TBD Call TI Call TI -40 to 85 LM4040B30ILP PREVIEW TO-92 LP 3 1000 TBD Call TI Call TI -40 to 85 LM4040B30ILPM PREVIEW TO-92 LP 3 2000 TBD Call TI Call TI -40 to 85 LM4040B30ILPR PREVIEW TO-92 LP 3 2000 TBD Call TI Call TI -40 to 85 LM4040B41IDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4M33 ~ 4M3U) LM4040B41IDBZT ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4M33 ~ 4M3U) LM4040B41IDBZTG4 ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4M33 ~ 4M3U) LM4040B41IDCKR ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 P5U LM4040B41ILP PREVIEW TO-92 LP 3 1000 TBD Call TI Call TI -40 to 85 LM4040B41ILPR PREVIEW TO-92 LP 3 2000 TBD Call TI Call TI -40 to 85 Addendum-Page 4 Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 25-Nov-2015 Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) LM4040B50IDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4NB3 ~ 4NBU) LM4040B50IDBZRG4 ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4NB3 ~ 4NBU) LM4040B50IDBZT ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4NB3 ~ 4NBU) LM4040B50IDCKR ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 MXU LM4040B50ILP PREVIEW TO-92 LP 3 1000 TBD Call TI Call TI -40 to 85 LM4040B50ILPR PREVIEW TO-92 LP 3 2000 TBD Call TI Call TI -40 to 85 LM4040B82IDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4NM3 ~ 4NMU) LM4040C10IDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4NS3 ~ 4NSU) LM4040C10IDBZT ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4NS3 ~ 4NSU) LM4040C10IDBZTG4 ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4NS3 ~ 4NSU) LM4040C10IDCKR ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 PKU LM4040C10ILP ACTIVE TO-92 LP 3 1000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFC10I LM4040C10ILPE3 ACTIVE TO-92 LP 3 1000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFC10I LM4040C10ILPR ACTIVE TO-92 LP 3 2000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFC10I LM4040C10ILPRE3 ACTIVE TO-92 LP 3 2000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFC10I LM4040C20IDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4MQ3 ~ 4MQU) LM4040C20IDBZT ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4MQ3 ~ 4MQU) LM4040C20IDBZTG4 ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4MQ3 ~ 4MQU) LM4040C20IDCKR ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 MVU Addendum-Page 5 Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 25-Nov-2015 Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) LM4040C20ILP ACTIVE TO-92 LP 3 1000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFC20I LM4040C20ILPE3 ACTIVE TO-92 LP 3 1000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFC20I LM4040C20ILPR ACTIVE TO-92 LP 3 2000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFC20I LM4040C20QDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 4MWU LM4040C20QDBZRG4 ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 4MWU LM4040C20QDBZT ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 4MWU LM4040C20QDBZTG4 ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 4MWU LM4040C25IDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4MU3 ~ 4MUU) LM4040C25IDBZRG4 ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4MU3 ~ 4MUU) LM4040C25IDBZT ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4MU3 ~ 4MUU) LM4040C25IDBZTG4 ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4MU3 ~ 4MUU) LM4040C25IDCKR ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 MUU LM4040C25IDCKT ACTIVE SC70 DCK 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 MUU LM4040C25IDCKTE4 ACTIVE SC70 DCK 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 MUU LM4040C25IDCKTG4 ACTIVE SC70 DCK 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 MUU LM4040C25ILP ACTIVE TO-92 LP 3 1000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFC25I LM4040C25ILPE3 ACTIVE TO-92 LP 3 1000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFC25I LM4040C25ILPR ACTIVE TO-92 LP 3 2000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFC25I Addendum-Page 6 Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 25-Nov-2015 Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) LM4040C25ILPRE3 ACTIVE TO-92 LP 3 2000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFC25I LM4040C25QDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 (4MA3 ~ 4MAU) LM4040C25QDBZRG4 ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 (4MA3 ~ 4MAU) LM4040C25QDBZT ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 (4MA3 ~ 4MAU) LM4040C25QDBZTG4 ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 (4MA3 ~ 4MAU) LM4040C30IDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4M83 ~ 4M8U) LM4040C30IDBZRG4 ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4M83 ~ 4M8U) LM4040C30IDBZT ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4M83 ~ 4M8U) LM4040C30IDBZTG4 ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4M83 ~ 4M8U) LM4040C30IDCKR ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 PBU LM4040C30IDCKT PREVIEW SC70 DCK 5 250 TBD Call TI Call TI -40 to 85 LM4040C30ILP ACTIVE TO-92 LP 3 1000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFC30I LM4040C30ILPE3 ACTIVE TO-92 LP 3 1000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFC30I LM4040C30ILPM PREVIEW TO-92 LP 3 2000 TBD Call TI Call TI -40 to 85 LM4040C30ILPR ACTIVE TO-92 LP 3 2000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFC30I LM4040C30QDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 4NJU LM4040C30QDBZT ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 4NJU LM4040C41IDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4M43 ~ 4M4U) LM4040C41IDBZRG4 ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4M43 ~ 4M4U) Addendum-Page 7 Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 25-Nov-2015 Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) LM4040C41IDBZT ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4M43 ~ 4M4U) LM4040C41IDBZTG4 ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4M43 ~ 4M4U) LM4040C41IDCKR ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 P6U LM4040C41IDCKRE4 ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 P6U LM4040C41IDCKRG4 ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 P6U LM4040C41ILP ACTIVE TO-92 LP 3 1000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFC41I LM4040C41ILPE3 ACTIVE TO-92 LP 3 1000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFC41I LM4040C41ILPR ACTIVE TO-92 LP 3 2000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFC41I LM4040C50IDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4NC3 ~ 4NCU) LM4040C50IDBZRG4 ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4NC3 ~ 4NCU) LM4040C50IDBZT ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4NC3 ~ 4NCU) LM4040C50IDBZTG4 ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4NC3 ~ 4NCU) LM4040C50IDCKR ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 MZU LM4040C50ILP ACTIVE TO-92 LP 3 1000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFC50I LM4040C50ILPE3 ACTIVE TO-92 LP 3 1000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFC50I LM4040C50ILPR ACTIVE TO-92 LP 3 2000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFC50I LM4040C50QDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 (4NE3 ~ 4NEU) LM4040C50QDBZT ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 (4NE3 ~ 4NEU) Addendum-Page 8 Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 25-Nov-2015 Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) LM4040C50QDBZTG4 ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 (4NE3 ~ 4NEU) LM4040C82IDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4NN3 ~ 4NNU) LM4040C82IDCKR ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 PFU LM4040C82ILP ACTIVE TO-92 LP 3 1000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFC82I LM4040C82ILPR ACTIVE TO-92 LP 3 2000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFC82I LM4040D20IDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4MV3 ~ 4MVU) LM4040D20IDBZRG4 ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4MV3 ~ 4MVU) LM4040D20IDBZT ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4MV3 ~ 4MVU) LM4040D20IDBZTG4 ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4MV3 ~ 4MVU) LM4040D20IDCKR ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 MWU LM4040D20IDCKRE4 ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 MWU LM4040D20IDCKRG4 ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 MWU LM4040D20ILPR ACTIVE TO-92 LP 3 2000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFD20I LM4040D20ILPRE3 ACTIVE TO-92 LP 3 2000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFD20I LM4040D20QDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 4MYU LM4040D20QDBZT ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 4MYU LM4040D20QDBZTG4 ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 4MYU LM4040D25IDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4ME3 ~ 4MEU) Addendum-Page 9 Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 25-Nov-2015 Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) LM4040D25IDBZRG4 ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4ME3 ~ 4MEU) LM4040D25IDBZT ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4ME3 ~ 4MEU) LM4040D25IDBZTG4 ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4ME3 ~ 4MEU) LM4040D25IDCKR ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 MEU LM4040D25IDCKRG4 ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 MEU LM4040D25IDCKT ACTIVE SC70 DCK 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 MEU LM4040D25IDCKTG4 ACTIVE SC70 DCK 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 MEU LM4040D25ILP ACTIVE TO-92 LP 3 1000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFD25I LM4040D25ILPE3 ACTIVE TO-92 LP 3 1000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFD25I LM4040D25ILPR ACTIVE TO-92 LP 3 2000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFD25I LM4040D25QDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 (4MB3 ~ 4MBU) LM4040D25QDBZRG4 ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 (4MB3 ~ 4MBU) LM4040D25QDBZT ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 (4MB3 ~ 4MBU) LM4040D25QDBZTG4 ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 (4MB3 ~ 4MBU) LM4040D30IDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4M93 ~ 4M9U) LM4040D30IDBZRG4 ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4M93 ~ 4M9U) LM4040D30IDBZT ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4M93 ~ 4M9U) LM4040D30IDBZTG4 ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4M93 ~ 4M9U) Addendum-Page 10 Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 25-Nov-2015 Status (1) LM4040D30IDCKR ACTIVE LM4040D30IDCKT LM4040D30ILP Package Type Package Pins Package Drawing Qty 3000 Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 Device Marking (4/5) SC70 DCK 5 PREVIEW SC70 DCK 5 250 TBD Call TI Call TI -40 to 85 ACTIVE TO-92 LP 3 1000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFD30I LM4040D30ILPE3 ACTIVE TO-92 LP 3 1000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFD30I LM4040D30ILPM PREVIEW TO-92 LP 3 2000 TBD Call TI Call TI -40 to 85 LM4040D30ILPR ACTIVE TO-92 LP 3 2000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFD30I LM4040D30ILPRE3 ACTIVE TO-92 LP 3 2000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFD30I LM4040D30QDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 4NKU LM4040D30QDBZRG4 ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 4NKU LM4040D41IDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4M53 ~ 4M5U) LM4040D41IDBZRG4 ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4M53 ~ 4M5U) LM4040D41IDBZT ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4M53 ~ 4M5U) LM4040D41IDBZTG4 ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4M53 ~ 4M5U) LM4040D41IDCKR ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 P7U LM4040D41ILP ACTIVE TO-92 LP 3 1000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFD41I LM4040D41ILPE3 ACTIVE TO-92 LP 3 1000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFD41I LM4040D41ILPR ACTIVE TO-92 LP 3 2000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFD41I LM4040D41ILPRE3 ACTIVE TO-92 LP 3 2000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFD41I LM4040D50IDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4ND3 ~ 4NDU) Addendum-Page 11 PCU Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 25-Nov-2015 Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) LM4040D50IDBZRG4 ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4ND3 ~ 4NDU) LM4040D50IDBZT ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4ND3 ~ 4NDU) LM4040D50IDBZTG4 ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4ND3 ~ 4NDU) LM4040D50IDCKR ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 M4U LM4040D50IDCKRG4 ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 M4U LM4040D50ILP ACTIVE TO-92 LP 3 1000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFD50I LM4040D50ILPE3 ACTIVE TO-92 LP 3 1000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFD50I LM4040D50ILPR ACTIVE TO-92 LP 3 2000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFD50I LM4040D50ILPRE3 ACTIVE TO-92 LP 3 2000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFD50I LM4040D50QDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 (4NF3 ~ 4NFU) LM4040D50QDBZT ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 (4NF3 ~ 4NFU) LM4040D82IDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4NP3 ~ 4NPU) LM4040D82IDBZT ACTIVE SOT-23 DBZ 3 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (4NP3 ~ 4NPU) LM4040D82IDCKR ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 PGU LM4040D82ILP ACTIVE TO-92 LP 3 1000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFD82I LM4040D82ILPR ACTIVE TO-92 LP 3 2000 Pb-Free (RoHS) CU SN N / A for Pkg Type -40 to 85 NFD82I (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. Addendum-Page 12 Samples PACKAGE OPTION ADDENDUM www.ti.com 25-Nov-2015 PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF LM4040C25 : • Enhanced Product: LM4040C25-EP NOTE: Qualified Version Definitions: • Enhanced Product - Supports Defense, Aerospace and Medical Applications Addendum-Page 13 PACKAGE MATERIALS INFORMATION www.ti.com 9-Dec-2015 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant LM4040A10IDCKR SC70 DCK 5 3000 179.0 8.4 2.2 2.5 1.2 4.0 8.0 Q3 LM4040A20IDCKR SC70 DCK 5 3000 179.0 8.4 2.2 2.5 1.2 4.0 8.0 Q3 LM4040A25IDCKR SC70 DCK 5 3000 179.0 8.4 2.2 2.5 1.2 4.0 8.0 Q3 LM4040A30IDCKR SC70 DCK 5 3000 179.0 8.4 2.2 2.5 1.2 4.0 8.0 Q3 LM4040A41IDCKR SC70 DCK 5 3000 179.0 8.4 2.2 2.5 1.2 4.0 8.0 Q3 LM4040A50IDCKR SC70 DCK 5 3000 179.0 8.4 2.2 2.5 1.2 4.0 8.0 Q3 LM4040A82IDCKR SC70 DCK 5 3000 179.0 8.4 2.2 2.5 1.2 4.0 8.0 Q3 LM4040B10IDCKR SC70 DCK 5 3000 179.0 8.4 2.2 2.5 1.2 4.0 8.0 Q3 LM4040B20IDCKR SC70 DCK 5 3000 179.0 8.4 2.2 2.5 1.2 4.0 8.0 Q3 LM4040B25IDCKR SC70 DCK 5 3000 179.0 8.4 2.2 2.5 1.2 4.0 8.0 Q3 LM4040B30IDCKR SC70 DCK 5 3000 179.0 8.4 2.2 2.5 1.2 4.0 8.0 Q3 LM4040B41IDCKR SC70 DCK 5 3000 179.0 8.4 2.2 2.5 1.2 4.0 8.0 Q3 LM4040B50IDCKR SC70 DCK 5 3000 179.0 8.4 2.2 2.5 1.2 4.0 8.0 Q3 LM4040C10IDCKR SC70 DCK 5 3000 179.0 8.4 2.2 2.5 1.2 4.0 8.0 Q3 LM4040C20IDCKR SC70 DCK 5 3000 179.0 8.4 2.2 2.5 1.2 4.0 8.0 Q3 LM4040C20QDBZR SOT-23 DBZ 3 3000 179.0 8.4 3.15 2.95 1.22 4.0 8.0 Q3 LM4040C20QDBZT SOT-23 DBZ 3 250 179.0 8.4 3.15 2.95 1.22 4.0 8.0 Q3 LM4040C25IDCKR SC70 DCK 5 3000 179.0 8.4 2.2 2.5 1.2 4.0 8.0 Q3 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 9-Dec-2015 Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant LM4040C25IDCKT SC70 DCK 5 250 179.0 8.4 2.2 2.5 1.2 4.0 8.0 Q3 LM4040C30IDCKR SC70 DCK 5 3000 179.0 8.4 2.2 2.5 1.2 4.0 8.0 Q3 LM4040C30QDBZR SOT-23 DBZ 3 3000 179.0 8.4 3.15 2.95 1.22 4.0 8.0 Q3 LM4040C30QDBZT SOT-23 DBZ 3 250 179.0 8.4 3.15 2.95 1.22 4.0 8.0 Q3 LM4040C41IDCKR SC70 DCK 5 3000 179.0 8.4 2.2 2.5 1.2 4.0 8.0 Q3 LM4040C50IDCKR SC70 DCK 5 3000 179.0 8.4 2.2 2.5 1.2 4.0 8.0 Q3 LM4040C82IDCKR SC70 DCK 5 3000 179.0 8.4 2.2 2.5 1.2 4.0 8.0 Q3 LM4040D20IDCKR SC70 DCK 5 3000 179.0 8.4 2.2 2.5 1.2 4.0 8.0 Q3 LM4040D20QDBZR SOT-23 DBZ 3 3000 179.0 8.4 3.15 2.95 1.22 4.0 8.0 Q3 LM4040D20QDBZT SOT-23 DBZ 3 250 179.0 8.4 3.15 2.95 1.22 4.0 8.0 Q3 LM4040D25IDCKR SC70 DCK 5 3000 179.0 8.4 2.2 2.5 1.2 4.0 8.0 Q3 LM4040D25IDCKT SC70 DCK 5 250 179.0 8.4 2.2 2.5 1.2 4.0 8.0 Q3 LM4040D30IDCKR SC70 DCK 5 3000 179.0 8.4 2.2 2.5 1.2 4.0 8.0 Q3 LM4040D30QDBZR SOT-23 DBZ 3 3000 179.0 8.4 3.15 2.95 1.22 4.0 8.0 Q3 LM4040D41IDCKR SC70 DCK 5 3000 179.0 8.4 2.2 2.5 1.2 4.0 8.0 Q3 LM4040D50IDCKR SC70 DCK 5 3000 179.0 8.4 2.2 2.5 1.2 4.0 8.0 Q3 LM4040D82IDCKR SC70 DCK 5 3000 179.0 8.4 2.2 2.5 1.2 4.0 8.0 Q3 *All dimensions are nominal Pack Materials-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 9-Dec-2015 Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM4040A10IDCKR SC70 DCK 5 3000 203.0 203.0 35.0 LM4040A20IDCKR SC70 DCK 5 3000 203.0 203.0 35.0 LM4040A25IDCKR SC70 DCK 5 3000 203.0 203.0 35.0 LM4040A30IDCKR SC70 DCK 5 3000 203.0 203.0 35.0 LM4040A41IDCKR SC70 DCK 5 3000 203.0 203.0 35.0 LM4040A50IDCKR SC70 DCK 5 3000 203.0 203.0 35.0 LM4040A82IDCKR SC70 DCK 5 3000 203.0 203.0 35.0 LM4040B10IDCKR SC70 DCK 5 3000 203.0 203.0 35.0 LM4040B20IDCKR SC70 DCK 5 3000 203.0 203.0 35.0 LM4040B25IDCKR SC70 DCK 5 3000 203.0 203.0 35.0 LM4040B30IDCKR SC70 DCK 5 3000 203.0 203.0 35.0 LM4040B41IDCKR SC70 DCK 5 3000 203.0 203.0 35.0 LM4040B50IDCKR SC70 DCK 5 3000 203.0 203.0 35.0 LM4040C10IDCKR SC70 DCK 5 3000 203.0 203.0 35.0 LM4040C20IDCKR SC70 DCK 5 3000 203.0 203.0 35.0 LM4040C20QDBZR SOT-23 DBZ 3 3000 203.0 203.0 35.0 LM4040C20QDBZT SOT-23 DBZ 3 250 203.0 203.0 35.0 LM4040C25IDCKR SC70 DCK 5 3000 203.0 203.0 35.0 LM4040C25IDCKT SC70 DCK 5 250 203.0 203.0 35.0 LM4040C30IDCKR SC70 DCK 5 3000 203.0 203.0 35.0 LM4040C30QDBZR SOT-23 DBZ 3 3000 203.0 203.0 35.0 LM4040C30QDBZT SOT-23 DBZ 3 250 203.0 203.0 35.0 LM4040C41IDCKR SC70 DCK 5 3000 203.0 203.0 35.0 LM4040C50IDCKR SC70 DCK 5 3000 203.0 203.0 35.0 LM4040C82IDCKR SC70 DCK 5 3000 203.0 203.0 35.0 LM4040D20IDCKR SC70 DCK 5 3000 203.0 203.0 35.0 LM4040D20QDBZR SOT-23 DBZ 3 3000 203.0 203.0 35.0 LM4040D20QDBZT SOT-23 DBZ 3 250 203.0 203.0 35.0 LM4040D25IDCKR SC70 DCK 5 3000 203.0 203.0 35.0 LM4040D25IDCKT SC70 DCK 5 250 203.0 203.0 35.0 LM4040D30IDCKR SC70 DCK 5 3000 203.0 203.0 35.0 LM4040D30QDBZR SOT-23 DBZ 3 3000 203.0 203.0 35.0 LM4040D41IDCKR SC70 DCK 5 3000 203.0 203.0 35.0 LM4040D50IDCKR SC70 DCK 5 3000 203.0 203.0 35.0 LM4040D82IDCKR SC70 DCK 5 3000 203.0 203.0 35.0 Pack Materials-Page 3 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2015, Texas Instruments Incorporated