Riedon CHR2512H Non-magnetic chip resistor Datasheet

CHR Series
Non-magnetic Chip Resistors
•
•
•
•
•
•
•
•
Resistances from 1 Ohm to 10M Ohms
Power Rating 0.05 to 2Watt
Resistance Tolerances to ± 0.5%
TCR’s to ± 50 ppm/°C
Non-Magnetic (contact PtAg)
Suitable for Gluing or Soldering
Sizes: 0402 / 0603 / 0805 / 1206 / 2010 / 2512 / 4020
Special High Temperature Version to 300°C (H)
(See ordering Information below)
SPECIFICATIONS
Type
0402 4
0603 4
0805 4
1206
2010
2512
4020
Power Rating ( W )
0.05
0.10
0.125
0.25
0.50
1.0 3
2.0 3
Trimmed
30
75
100
200
250
300
500
Untrimmed
(≥ 5% tol.)
60
150
200
400
900
1200
1200
Working 2
Voltage
( VAC )
Resistance Range
(Ω)
Tolerances Available ( % )
Temperature Coefficients Available ( ± ppm/°C ) 1 (others upon request)
1Ω - <10Ω
10% to 20%
250
5% to 20%
100 / 250
5% to 20%
100 / 250
5% to 20%
100 / 250
5% to 20%
100 / 250
5% to 20%
100 / 250
5% to 20%
100 / 250
10Ω - <100Ω
5% to 10%
100
2% to 10%
50 / 100
1% to 10%
50 / 100
1% to 10%
50 / 100
1% to 10%
50 / 100
1% to 10%
50 / 100
1% to 10%
50 / 100
100Ω - 1M
1% to 10%
50 / 100
1% to 10%
50 / 100
0.5% to
10%
50 / 100
0.5% to
10%
50 / 100
0.5% to
10%
50 / 100
0.5% to
10%
50 / 100
0.5% to
10%
50 / 100
>1M - 10M
5% to 20%
50 / 100
1% to 10%
50 / 100
1% to 10%
50 / 100
1% to 10%
50 / 100
1% to 10%
50 / 100
1% to 10%
50 / 100
1% to 10%
50 / 100
1) TCR: in ppm/C; +25°C...+125°C; TCR below standard TCR (highest value): +25°C...+85°C
2) Continuous operating voltage (U_, Ueff): V ≤ #(P*R) or max. working voltage (the lower value)
3) Solder pads must be sufficiently large to keep resistors’s peak temperature below rating
4) Best tolerance for HIgh Temp version is 2%
Specification
Value
Temperature Range
-55°C to +155°C (Standard)
-55°C to +125°C (50ppm/°C Parts)
-55°C to +300°C (High Temperature Version, TCR valid +25°C to +125°C )
Climactic Cetegory
55 / 155 / 56
Solderability
250°C / 3s (up to 6 months after shipment or 12 monts at storage in Nitrogen)
Max. Soldering Temperature
260°C / 10s
Riedon Inc.
5/16
300 Cypress Avenue
Alhambra CA 91801
www.riedon.com
(626) 284-9901
(626) 284-1704
CHR Series
Non-magnetic Chip Resistors
SPECIFICATIONS (continued)
Max ∆R
Long Term Stability
<10Ω
10Ω - 10M
Storage 125°C / 1000h
±1%
±0.5%
Storage 155°C / 1000h
±2%
±1%
Load Life / P=70% / 70°C / 1000h
±1%
±0.5%
±0.5%
±0.25%
±1%
±0.5%
Short term overload
Humidity / 96%RH / 40°C / 56 days
This part is RoHS complian with exemption 7(c)-I, as authorized by 2011/b5/EU.
RoHS Compliant Exemption
Dimensions
Type
L
B
D
C
CHR 0402 /
CHR 0402H
0.95 +0.10 / 0.05
0.48 +0.10 / -0.05
0.28 +0.1 / -0.05
0.1 +0.1 / -0.05
CHR 0603 /
CHR 0603H
1.5 +0.15 / -0.05
0.8 +0.15 / -0.05
0.4 +0.15 / -0.05
0.2 +0.2 / -0.1
CHR 0805 /
CHR 0805H
2.0 +0.15 / -0.05
1.25 +0.15 / -0.05
0.4 +0.15 / -0.05
0.3 +0.2 / -0.1
CHR 1206 /
CHR 1206H
3.2 +0.15 / -0.05
1.5 +0.2 / -0.05
0.4 +0.15 / -0.05
0.3 +0.2 / -0.1
CHR 2010 /
CHR 2010H
5.1 +0.15 / -0.05
2.5 +0.2 / -0.05
0.6 +0.20 / -0.1
1.2 ±0.2
CHR 2512 /
CHR 2512H
6.3 +0.15 / -0.05
3.5 +0.2 / -0.05
0.6 +0.15 / -0.05
0.9 ±0.2
CHR 4020 /
CHR 4020H
10.2 +0.15 / -0.05
5.1 +0.2 / -0.05
0.6 +0.15 / -0.05
0.9 ±0.2
Packaging:
Power Derating Curve
Bulk or Blistertape to IEC 60286-3
120
Tape width 8mm / Reel Diameter 180 or 330mm
Minimum quantity Bulk / 100 pieces per value
Minimum quantity Tape & Reel / 500 pieces per value
(Note: Except size 0402 / 1000 pieces per value)
Alhambra CA 91801
www.riedon.com
n
5/16
300 Cypress Avenue
si o
Riedon Inc.
er
)V
ard
40
20
0
0
High Temperature Part Description (H): Part Type H - Resistance - Tolerance - TCR
Example: CHR 0805H 50 kOhms 10% 50ppm
( Note: if no TCR is specified, the highest value will be supplied )
(H
60
nd
Standard Part Description: Part Type - Resistance - Tolerance - TCR
Example: CHR 0603 10 kOhms 5% 50ppm
( Note: if no TCR is specified, the highest value will be supplied )
80
Sta
Ordering Information
Power ( % )
100
50
100
150
200
250
300
350
Ambient Temperature (°C)
(626) 284-9901
(626) 284-1704
Similar pages