MHI100DI5.7Series High Isolation, 1W SIP Single & Dual Output DC/DC Converters Electrical Specifications Key Features: • 1W Output Power Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Input Parameter Conditions Min. 5 VDC Input 4.5 12 VDC Input 10.8 15 VDC Input 13.5 24 VDC Input 21.6 Capacitor Filter • 5.7 kV Isolation • 15 kV/µS CMTI Input Voltage Range • 40 Standard Models • Miniature SIP Case Input Filter Typ. 5.0 12.0 15.0 24.0 Max. 5.5 13.2 16.5 26.4 Units Typ. Max. ±5.0 ±1.0 Units % % % 100 ±0.02 mV P - P %/°C Max. Units VDC • -40°C to +85°C Operation Output • Industry Standard Pin-Out Parameter • Low Cost Conditions Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation, See Note 2 Ripple & Noise (20 MHz) Temperature Coefficient Output Short Circuit Min. Dual Output, Balanced Loads ±0.1 For VIN Change of 1% ±1.2 See Model Selection Guide See Note 3 ±0.01 Momentary (0.5 Sec Max) General Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Common Mode Transient Immunity Switching Frequency Conditions Rated For 60 Sec Tested For 1 Sec 500 VDC 100 kHz, 1V Min. 5,200 5,700 10 Typ. VDC G pF kV/µS kHz 7 15 100 Environmental Parameter Conditions Ambient Case Operating Temperature Range MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA Storage Temperature Range Cooling Humidity Physical Case Size Case Material Weight Min. -40 Typ. +25 -55 Free Air Convection RH, Non-condensing Max. +85 +100 +125 Units 95 % °C °C See Mechanical Diagram (Page 3) Non-Conductive Black Plastic (UL94-V0) 0.08 Oz (2.4g) Reliability Specifications Parameter MTBF Conditions MIL HDBK 217F, 25°C, Gnd Benign Min. 2.0 Typ. Max. Units MHours Min. Typ. Max. 9.0 18.0 20.0 30.0 260 Units Absolute Maximum Ratings T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Parameter Conditions Input Voltage Surge (0.1 Sec) Lead Temperature 5 VDC Input 12 VDC Input 15 VDC Input 24 VDC Input 1.5 mm From Case for 10 Sec Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. www.micropowerdirect.com VDC °C www.micropowerdirect.com Model Selection Guide Input Model Number Voltage (VDC) Nominal 5 5 5 5 5 5 5 5 5 Range 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 MHI105D-1509DI5.7 5 4.5 - 5.5 MHI112S-03DI5.7 MHI112S-05DI5.7 MHI112S-09DI5.7 MHI112S-12DI5.7 MHI112S-15DI5.7 MHI112D-05DI5.7 MHI112D-09DI5.7 MHI112D-12DI5.7 MHI112D-15DI5.7 12 12 12 12 12 12 12 12 12 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 MHI112D-1509DI5.7 12 10.8 - 13.2 MHI115S-03DI5.7 MHI115S-05DI5.7 MHI115S-09DI5.7 MHI115S-12DI5.7 MHI115S-15DI5.7 MHI115D-05DI5.7 MHI115D-09DI5.7 MHI115D-12DI5.7 MHI115D-15DI5.7 15 15 15 15 15 15 15 15 15 13.5 - 16.5 13.5 - 16.5 13.5 - 16.5 13.5 - 16.5 13.5 - 16.5 13.5 - 16.5 13.5 - 16.5 13.5 - 16.5 13.5 - 16.5 MHI115D-1509DI5.7 15 13.5 - 16.5 MHI124S-03DI5.7 MHI124S-05DI5.7 MHI124S-09DI5.7 MHI124S-12DI5.7 MHI124S-15DI5.7 MHI124D-05DI5.7 MHI124D-09DI5.7 MHI124D-12DI5.7 MHI124D-15DI5.7 24 24 24 24 24 24 24 24 24 21.6 - 26.4 21.6 - 26.4 21.6 - 26.4 21.6 - 26.4 21.6 - 26.4 21.6 - 26.4 21.6 - 26.4 21.6 - 26.4 21.6 - 26.4 MHI124D-1509DI5.7 24 21.6 - 26.4 MHI105S-03DI5.7 MHI105S-05DI5.7 MHI105S-09DI5.7 MHI105S-12DI5.7 MHI105S-15DI5.7 MHI105D-05DI5.7 MHI105D-09DI5.7 MHI105D-12DI5.7 MHI105D-15DI5.7 Output Current (mA) Voltage Full-Load No-Load (VDC) 286 35 3.3 286 35 5.0 266 35 9.0 261 35 12.0 254 35 15.0 282 35 ±5.0 269 35 ±9.0 262 35 ±12.0 254 35 ±15.0 +15.0 260 35 -9.0 117 17 3.3 117 17 5.0 110 17 9.0 108 17 12.0 104 17 15.0 116 17 ±5.0 111 17 ±9.0 108 17 ±12.0 104 17 ±15.0 +15.0 107 17 -9.0 95 16 3.3 95 16 5.0 89 16 9.0 90 16 12.0 84 16 15.0 94 16 ±5.0 90 16 ±9.0 86 16 ±12.0 84 16 ±15.0 +15.0 87 16 -9.0 60 12 3.3 60 12 5.0 56 12 9.0 53 12 12.0 52 12 15.0 59 12 ±5.0 56 12 ±9.0 55 12 ±12.0 53 12 ±15.0 +15.0 55 12 -9.0 Notes: 1. The specified maximum capacitive load is for each output. 2. Load regulation is measured over a range of 20% IOUT to 100% IOUT. 3. When measuring output ripple & noise, it is recommended that an external capacitor (1 µF typ.) be placed from the +VOUT to the -VOUT pins for single output units and from each output to common for dual output models. 4. The converter should be connected to a low ac-impedance source. An input source with a highly inductive impedance may affect the stability of the converter. In applications where the converter output loading is high and input power is supplied over long lines, it may be necessary to use a capacitor on the input to insure start-up. In this case, it is recommended that a low ESR (ESR <1.0⍀ at 100 kHz) capacitor be mounted close to the converter. For 5V input units a 2.2 µF is recommended; for 12V & 15V input units, a 1.0 µF; and for 24V units a 0.47 µF. 5. Operation at no-load will not damage the unit, but they may not meet all specifications. 6. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection tables for the correct rating. MicroPower Direct • 292 Page Street Ste D Stoughton, MA 02072 Current Current (mA, Max) (mA, Min) 303 200 111 84 66 ±100 ±56 ±42 ±33 +33 -55 303 200 111 84 66 ±100 ±56 ±42 ±33 +33 -55 303 200 111 84 66 ±100 ±56 ±42 ±33 +33 -55 303 200 111 84 66 ±100 ±56 ±42 ±33 +33 -55 Fuse Capacitive Load Efficiency Regulation Rating Load (%, Typ) Slow-Blow (%, Max) (µF, Max) (mA) 0.0 0.0 0.0 0.0 0.0 ±0.0 ±0.0 ±0.0 ±0.0 70 70 75 77 78 71 75 77 78 ±20.0 ±15.0 ±10.0 ±10.0 ±10.0 ±15.0 ±10.0 ±10.0 ±10.0 ±0.0 76 ±10.0 0.0 0.0 0.0 0.0 0.0 ±0.0 ±0.0 ±0.0 ±0.0 71 71 76 78 79 72 75 78 79 ±20.0 ±15.0 ±10.0 ±10.0 ±10.0 ±15.0 ±10.0 ±10.0 ±10.0 ±0.0 77 ±10.0 0.0 0.0 0.0 0.0 0.0 ±0.0 ±0.0 ±0.0 ±0.0 70 70 75 75 79 71 75 78 79 ±20.0 ±15.0 ±10.0 ±10.0 ±10.0 ±15.0 ±10.0 ±10.0 ±10.0 ±0.0 76 ±10.0 0.0 0.0 0.0 0.0 0.0 ±0.0 ±0.0 ±0.0 ±0.0 70 70 75 78 80 71 75 77 78 ±20.0 ±15.0 ±10.0 ±10.0 ±10.0 ±15.0 ±10.0 ±10.0 ±10.0 ±0.0 75 ±10.0 1,000 470 470 220 220 220 220 100 100 100 220 1,000 470 470 220 220 220 220 100 100 100 220 1,000 470 470 220 220 220 220 100 100 100 220 1,000 470 470 220 220 220 220 100 100 100 220 500 500 500 500 500 500 500 500 500 500 500 250 250 250 250 250 250 250 250 250 250 250 200 200 200 200 200 200 200 200 200 200 200 150 150 150 150 150 150 150 150 150 150 150 Derating Curve • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected] www.micropowerdirect.com IGBT Applications Notes: The MHI100x-xxD series is a good choice for IGBT applications. They are designed to withstand the extra stress caused by the high voltage switching transients present in IGBT drive circuits. The MHI1xxD-1509DI5.7 models are specifically designed for use with “962” type drivers. The IGD962 (available from MPD) is a hybrid integrated circuit specifically designed to drive N-channel IGBT modules. It provides the I/O isolation, high speed, drive voltage stability and fault protection required to control most MOS gated power devices. The drawing at right illustrates a typical connection of the MHI105D-1509DI5.7 to the IGD962. For more information on this connection, please contact the factory. Mechanical Dimensions Pin Connections Pin 1 2 5 6 7 Single Output +VIN -VIN -VOUT No Pin +VOUT Pin 1 2 5 6 7 Dual Output +VIN -VIN -VOUT Common +VOUT Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.02 (±0.50) MicroPower Direct We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]