3.2x2.4mm SMD CHIP LED LAMP Part Number: APD3224SGC-F01 Super Bright Green Features Description z 3.2x2.4mm SMT LED, 2.4mm thickness. The Super Bright Green source color devices are made with z Low power consumption. Gallium Phosphide Green Light Emitting Diode. z Ideal for backlight and indicator. z Package : 1500pcs / reel. z Moisture sensitivity level : level 3. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.1(0.004") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAF1086 REV NO: V.8B DATE: FEB/04/2015 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng PAGE: 1 OF 5 ERP: 1203006985 Selection Guide Part No. Dice APD3224SGC-F01 Super Bright Green (GaP) Viewing Angle [1] Iv (mcd) [2] @ 20mA Lens Type Min. Typ. 2θ1/2 55 100 20° Water Clear Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. 3. Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength Super Bright Green λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 565 nm IF=20mA Super Bright Green 568 nm IF=20mA Spectral Line Half-width Super Bright Green 30 nm IF=20mA C Capacitance Super Bright Green 15 pF VF=0V;f=1MHz VF [2] Forward Voltage Super Bright Green 2.2 2.5 V IF=20mA IR Reverse Current Super Bright Green 10 uA VR=5V Notes: 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. 4. Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Super Bright Green Units 62.5 mW DC Forward Current 25 mA Peak Forward Current [1] 140 mA 5 V Power dissipation Reverse Voltage Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAF1086 REV NO: V.8B DATE: FEB/04/2015 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng PAGE: 2 OF 5 ERP: 1203006985 Super Bright Green APD3224SGC-F01 SPEC NO: DSAF1086 REV NO: V.8B DATE: FEB/04/2015 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng PAGE: 3 OF 5 ERP: 1203006985 APD3224SGC-F01 Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAF1086 REV NO: V.8B DATE: FEB/04/2015 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng PAGE: 4 OF 5 ERP: 1203006985 PACKING & LABEL SPECIFICATIONS APD3224SGC-F01 Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAF1086 REV NO: V.8B DATE: FEB/04/2015 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng PAGE: 5 OF 5 ERP: 1203006985