CD22101, CD22102 Semiconductor T CMOS 4 E PRODUC OBSOLET CEMENT A L P E R D E D MEN 0-442-7747 NO RECOM ations 1-80 .com c li p p A l a arris Call Centr entapp@h or email: c Description February 1999 Features • Low ON Resistance . . . . . . . . . . . . 75Ω (Typ) at VDD = 12V • “Built - In” Latched Inputs • Large Analog Signal Capability . . . . . . . . . . . . . . . ±VDD/2 • Switch Bandwidth . . . . . . . . . . . . . . . . . . . . . . . . . . 10MHz • Matched Switch Characteristics ∆RON = 8Ω (Typ) at VDD = 12V • High Linearity - 0.25% Distortion (Typ) at f = 1kHz, VIN = 5VP-P, VDD - VSS = 10V, and RL = 1kΩ • Standard CMOS Noise Immunity Applications • Telephone Systems • PBX • Studio Audio Switching • Multisystem Bus Interconnect Ordering Information PART NUMBER TEMP. RANGE (oC) PACKAGE PKG. NO. CD22101E -40 to 85 24 Ld PDIP E24.6 CD22101F -55 to 125 24 Ld CERDIP F24.6 CD22102E -40 to 85 24 Ld PDIP E24.6 CD22101 and CD22102 crosspoint switches consist of 4 x 4 x 2 arrays of crosspoints (transmission gates) with a 4-line to 16-line decoder and 16 latch circuits. Any one of the sixteen crosspoint pairs can be selected by applying the appropriate four-line address, corresponding crosspoints in each array are turned on and off simultaneously. Any number of crosspoints can be turned on simultaneously. In the CD22101, the selected crosspoint pair can be turned on or off by applying a logic ONE or ZERO, respectively, to the data input, and applying a ONE to the strobe input. When the device is “powered up”, the states of the 16 switches are indeterminate. Therefore, all switches must be turned off by putting the strobe high, data-in low, and then addressing all switches in succession. The selected pair of crosspoints in the CD22102 is turned on by applying a logic ONE to the KA (set) input while a logic ZERO is on the KB input, and turned off by applying a logic ONE to the KB (reset) input while a logic ZERO is on the KA input. In this respect, the control latches of the CD22102 are similar to SET/RESET flip-flops. They differ, however, in that the simultaneous application of ONEs to the KA and KB inputs turns off (resets) all crosspoints. All crosspoints in both devices must be turned off as VDD is applied. Functional Diagram Pinouts CD22101 (PDIP, SBDIP) TOP VIEW CONTROL CD22102 (PDIP) TOP VIEW IN (OUT) 16 B 1 24 VDD C 2 23 A B 1 C 2 24 VDD 23 A X2' 3 22 X2 X2' 3 22 X2 Y1' 4 21 Y1 Y1' 4 21 Y1 Y2' 5 20 Y2 Y2' 5 20 Y2 X4' 6 19 X4 X4' 6 19 X4 X3' 7 18 X3 X3' 7 18 X3 Y4' 8 17 Y4 Y4' 8 17 Y4 Y3' 9 16 Y3 Y3' 9 16 Y3 X1' 10 15 X1 X1' 10 15 X1 D 11 14 KA VSS 12 13 KB D 11 VSS 12 14 DATA 13 STROBE ADDRESS [ /Title (CD22 101, CD221 02) /Subject (CMO S4x4 x2 Crosspoint Switch with Control Memory) / Author () /Keywords (Harris Semiconductor, Telecom, SLICs, SLACs , Telephone, Telephony, WLL, Wireless x 4 x 2 Crosspoint Switch with Control Memory © Harris Corporation 1999 4-193 OUT (IN) 4X4 SWITCH OUT (IN) DECODER LATCH 16 CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper IC Handling Procedures. Copyright 4X4 SWITCH 16 IN (OUT) File Number 2871.3 CD22101, CD22102 Absolute Maximum Ratings Thermal Information Supply Voltage (VDD) (Referenced to VSS Terminal) . . . .-0.5 to 20V Input Voltage (All Inputs) . . . . . . . . . . . . . . . . . . . -0.5 to VDD +0.5V Supply Voltage Range For TA = Full Package Temperature Range . . . . . . . . . . . . . . 3V to 18V Input Current (Any One Input) (Note 1) . . . . . . . . . . . . . . . . . . .±10mA Power Dissipation For TA = -40oC to 60oC (Package Type E) . . . . . . . . . . . . 500mW For TA = 60oC to 85oC Package Type E) . . . . . . . . Derate Linearly 12mW/oC to 200mW For TA = -55oC to 100oC (Package Type D, F) . . . . . . . . . 500mW For TA = 100oC to 125oC (Package Type D, F) . . . . . Derate Linearly 12mW/oC to 200mW Device Dissipation per Output Transistor For TA = Full Package Temperature Range (All Types) . . . . . 100mW Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 175oC Maximum Junction Temperature (Plastic Package) . . . . . . . . 150oC Maximum Storage Temperature Range . . . . . . -65oC ≤ TA ≤ 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC Operating Conditions Temperature Range Package Type D, F. . . . . . . . . . . . . . . . . . . . . -55oC ≤ TA ≤ 125oC Package Type E . . . . . . . . . . . . . . . . . . . . . . . . -40oC ≤ TA ≤ 85oC CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Electrical Specifications Values at -55oC, 25oC, 125oC Apply to D, F, H Packages Values at -40oC, 25oC, 85oC Apply to E Package TEST CONDITIONS PARAMETER FIGURE VDD(V) SYMBOL -55oC -40oC 85oC 125oC 25oC MAX MAX MAX MAX MIN TYP MAX UNITS STATIC CROSSPOINTS Quiescent Device Current On Resistance ∆ON Resistance OFF Leakage Current 1 5 5 5 150 150 - 0.04 5 µA 1 10 10 10 300 300 - 0.04 10 µA 1 15 20 20 600 600 - 0.04 20 µA 1 20 100 100 3000 3000 - 0.08 100 µA 14 5 475 500 725 800 - 225 600 Ω 15 10 135 145 205 230 - 85 180 Ω - 12 100 110 155 175 - 75 135 Ω 16 15 70 75 110 125 - 65 95 Ω IDD (Max) RON (Max) Any Switch VIS = 0 to VDD ∆RON Between Any Two Switches IL (Max) All Switches OFF, VIS = 18V 4 5 - - - - - 25 - Ω 10 - - - - - 10 - Ω 12 - - - - - 8 - Ω 15 - - - - - 5 - Ω 18 ±1000 - ±1 ±100 (Note 2) nA 5 1.5 - - 1.5 V 10 3 - - 3 V STATIC CONTROLS Input Low Voltage Input High Voltage VIL (Max) OFF Switch IL < 0.2µA VIH (Min) ON Switch See RON Characteristic 15 4 - - 4 V 5 3.5 3.5 - - V 10 7 7 - - V 15 Input Current IIN (Max) Any Control VIN = 0, 18V 2 11 ±0.1 18 ±0.1 NOTES: 1. Maximum current through transmission gates (switches) = 25mA. 2. Determined by minimum feasible leakage measurement for automatic testing. 4-194 ±1 ±1 11 - - V - ±10-5 ±0.1 µA CD22101, CD22102 Electrical Specifications TA = 25oC TEST CONDITIONS PARAMETER SYMBOL FIGURE fIS (kHz) RL (kΩ) VIS (V) (Note 3) VDD (V) MIN TYP MAX UNITS tPHL, tPLH 5 - - 5 5 - 30 60 ns - 10 10 10 - 15 30 ns 15 15 - 10 20 ns 10 - 40 - MHz DYNAMIC CROSSPOINTS Propagation Delay Time, (Switch ON) Signal Input to Output CL = 50pF; tR , tF = 20ns Frequency Response (Any Switch ON) f3dB Sine Wave Response (Distortion) THD Feedthrough (All Switches OFF) 19 1 1 5 V OS Sine Wave Input, 20log ----------- = -3dB V IS FDT - 13 1 1 2.5 5 - 1 - % 1 1 5 10 - 0.25 - % 1 1 7.5 15 - 0.15 - % 1.6 0.6 2 (Note 4) 10 - -96 - dB - 2.5 - MHz Sine Wave Input Frequency for Signal Crosstalk FCT 12 - 0.6 1 (Note 4) 10 Attenuation of 40dB Attenuation of 95dB Sine Wave Input 0.1 kHz Capacitance: XN to Ground CIS YN to Ground Feedthrough CIOS - - - - 25 - pF - - - - 60 - pF - - - - 0.6 - pF 5 - 500 1000 ns 10 - 230 460 ns 15 - 170 340 ns 5 - 515 1000 ns 10 - 220 440 ns 15 - 170 340 ns 5 - 500 1000 ns 10 - 215 430 ns 15 - 160 320 ns 5 - 480 960 ns 10 - 225 450 ns 15 - 155 300 ns DYNAMIC CONTROLS Propagation Delay Time: High Impedance to High Level or Low Level tPZH, tPZL 6 RL = 1kΩ, CL = 50pF, tR, tF = 20ns Strobe to Output, CD22101 Data-In to Output, CD22101 KA to Output, CD22102 Address to Output CD22101, CD22102 tPZH, tPZL tPZH, tPZL tPZH, tPZL 7 - 8 RL = 1kΩ, CL = 50pF, tR, tF = 20ns RL = 1kΩ, CL = 50pF, tR, tF = 20ns RL = 1kΩ, CL = 50pF, tR, tF = 20ns 4-195 CD22101, CD22102 Electrical Specifications TA = 25oC (Continued) TEST CONDITIONS PARAMETER SYMBOL FIGURE Propagation Delay Time: High Level or Low Level to High Impedance tPHZ, tPLZ 6 fIS (kHz) RL (kΩ) RL = 1kΩ, CL = 50pF, tR, tF = 20ns Strobe to Output, CD22101 KB to Output, CD22102 Data-In to Output, CD22101 KA • KB to Output, CD22102 Address to Output CD22101, CD22102 Minimum Strobe Pulse Width, CD22101 Address to Strobe Setup or Hold Times, CD22101 Strobe to Data-In Hold Time, CD22101 Address to KA and KB Setup or Hold Times, CD22102 Minimum KA • KB Pulse Width, CD22102 Minimum KA Pulse Width, CD22102 tPHZ, tPLZ tPHZ, tPLZ tPHZ, tPLZ tPHZ, tPLZ tW tSU, tH tHHL, tHLH tSU, tH tW tW - - - 8 6 9 10 - - - RL = 1kΩ, CL = 50pF, tR, tF = 20ns RL = 1kΩ, CL = 50pF, tR, tF = 20ns RL = 1kΩ, CL = 50pF, tR, tF = 20ns RL = 1kΩ, CL = 50pF, tR, tF = 20ns RL = 1kΩ, CL = 50pF, tR, tF = 20ns RL = 1kΩ, CL = 50pF, tR, tF = 20ns RL = 1kΩ, CL = 50pF, tR, tF = 20ns RL = 1kΩ, CL = 50pF, tR, tF = 20ns RL = 1kΩ, CL = 50pF, tR, tF = 20ns RL = 1kΩ, CL = 50pF, tR, tF = 20ns 4-196 VIS (V) (Note 3) VDD (V) MIN TYP MAX UNITS 5 - 450 900 ns 10 - 200 400 ns 15 - 135 270 ns 5 - 450 900 ns 10 - 200 400 ns 15 - 130 260 ns 5 - 450 900 ns 10 - 165 330 ns 15 - 110 220 ns 5 - 280 560 ns 10 - 130 260 ns 15 - 90 180 ns 5 - 425 850 ns 10 - 190 380 ns 15 - 130 260 ns 5 - 260 500 ns 10 - 120 240 ns 15 - 80 160 ns 5 - -160 0 ns 10 - -70 0 ns 15 - -50 0 ns 5 - 200 400 ns 10 - 80 160 ns 15 - 60 120 ns 5 - -160 0 ns 10 - -70 0 ns 15 - -50 0 ns 5 - 375 750 ns 10 - 160 320 ns 15 - 110 220 ns 5 - 425 850 ns 10 - 175 350 ns 15 - 120 240 ns CD22101, CD22102 TA = 25oC (Continued) Electrical Specifications TEST CONDITIONS PARAMETER SYMBOL FIGURE Minimum KB Pulse Width, CD22102 tW - Control Crosstalk, Data-In, Address or Strobe to Output fIS (kHz) RL (kΩ) VIS (V) (Note 3) RL = 1kΩ, CL = 50pF, tR, tF = 20ns 11 100 VDD (V) MIN TYP MAX UNITS 5 - 200 400 ns 10 - 90 180 ns 15 - 70 140 ns 5 - 75 - mVPEAK - - 5 7.5 pF 10 Square Wave Input = 5V, tR, tF = 20ns, RS = 1kΩ Input Capacitance CIN Any Control Input NOTES: V DD 3. Peak-to-peak voltage symmetrical about ----------, unless otherwise specified. 2 4. RMS. Functional Block Diagram CD22102 ONLY KB 21 KA 0 1 2 3 CD22101 ONLY STROBE (NOTE) 13 Y2 20 DATA (NOTE) Y1 4 5 6 SIGNALS OUT (IN) 7 Y3 14 16 16 23 A (NOTE) 8 9 10 11 Y4 17 LATCHES DECODER 12 13 14 15 1 B (NOTE) 15 16 ADDRESS 16 22 X1 2 18 X2 19 X3 X4 SIGNALS IN (OUT) C (NOTE) 4 11 D (NOTE) 16 0’ 1’ 2’ Y1’ 3’ Y2’ 5 4’ VDD 5’ 6’ SIGNALS OUT (IN) 7’ Y3’ 9 8’ NOTE: INPUTS PROTECTED BY COS/MOS PROTECTION NETWORK 9’ 10’ 11’ Y4’ 8 12’ 13’ 10 14’ 3 15’ 7 X1’ X2’ X3’ SIGNALS IN (OUT) VSS 4-197 6 X4’ CD22101, CD22102 Schematic Diagram (NOTE) STROBE 13 (NOTE) DATA IN 14 21 Y1 TO X1’ Y1’ 24 VDD A D Q B ø C 23 A (NOTE) TO 15 OTHER NANDS B 1 B (NOTE) Y2 TG TG KA (SET) (NOTE) 14 KB (RESET) (NOTE) 13 A B C D 16 TG TG TG ø ø 17 Y4 R TG TG 9 ( Y3’ ) TG 8 9 10 11 D Q 5 ( Y2’ ) TG Y3 TG 8 ( Y4’ ) TG 12 13 14 15 C TO 15 OTHER NANDS D 11 TG 4 5 6 7 TO 15 OTHER LATCHS C C (NOTE) TG CD22101 B 2 TG 20 LATCH A TG 0 1 2 3 ø D A TG 4 ( Y1’ ) ( D 15 X1 10 X1’ ) 22 ( X2 3 X2’ ) 18 ( X3 7 X3’ ) ( 19 X4 6 X4’ ) D (NOTE) TO 15 OTHER LATCHES 12 DETAIL OF TRANSMISSION GATES CD22102 VSS VDD IN VDD DETAIL OF LATCHES VDD ø NOTE: INPUTS PROTECTED BY COS/MOS PROTECTION NETWORK D p n Q ø OUT ø p n VSS Q ø VSS DECODER TRUTH TABLE ADDRESS ADDRESS A B C D SELECT A B C D SELECT 0 0 0 0 X1Y1 and X1’Y1’ 0 0 0 1 X1Y3 and X1’Y3’ 1 0 0 0 X2Y1 and X2’Y1’ 1 0 0 1 X2Y3 and X2’Y3’ 0 1 0 0 X3Y1 and X3’Y1’ 0 1 0 1 X3Y3 and X3’Y3’ 1 1 0 0 X4Y1 and X4’Y1’ 1 1 0 1 X4Y3 and X4’Y3’ 0 0 1 0 X1Y2 and X1’Y2’ 0 0 1 1 X1Y4 and X1’Y4’ 1 0 1 0 X2Y2 and X2’Y2’ 1 0 1 1 X2Y4 and X2’Y4’ 0 1 1 0 X3Y2 and X3’Y2’ 0 1 1 1 X3Y4 and X3’Y4’ 1 1 1 0 X4Y2 and X4’Y2’ 1 1 1 1 X4Y4 and X4’Y4’ 4-198 CD22101, CD22102 CONTROL TRUTH TABLE FOR CD22101 ADDRESS FUNCTION A B C D STROBE DATA SELECT Switch ON 1 1 1 1 1 1 15 (X4Y4) and 15’ (X4’Y4’) Switch OFF 1 1 1 1 1 0 15 (X4Y4) and 15’ (X4’Y4’) No Change X X X X 0 X X X X X 1 = High Level 0 = Low Level X = Don’t Care CONTROL TRUTH TABLE FOR CD22102 ADDRESS FUNCTION A B C D KA KB SELECT Switch ON 1 1 1 1 1 0 15 (X4Y4) and 15’ (X4’Y4’) Switch OFF 1 1 1 1 0 1 15 (X4Y4) and 15’ (X4’Y4’) All Switches OFF (Note 5) X X X X 1 1 All No Change X X X X 0 0 X X X X 1 = High Level 0 = Low Level X = Don’t Care NOTE: 5. In the event that KA and KB are changed from levels 1, 1 to 0, 0 KB should not be allowed to go to 0 before KA, otherwise a switch which was off will inadvertently be turned on. Metallization Mask Layout Dimensions in parenthesis are in millimeters and are derived from the basic inch dimensions as indicated. Grid graduations are in mils (10-3 inch). 4-199 CD22101, CD22102 Test Circuits and Waveforms VDD VDD VDD VDD IDD 1 24 2 23 3 22 4 21 5 20 6 19 7 18 8 17 9 16 10 15 11 14 12 13 VSS II VSS 1 24 2 23 3 22 4 21 5 20 6 19 7 18 8 17 9 16 10 15 11 14 12 13 VSS VSS MEASURE INPUTS SEQUENTIALLY TO BOTH VDD AND VSS CONNECT ALL UNUSED INPUTS TO EITHER VDD OR VSS FIGURE 1. QUIESCENT CURRENT TEST CIRCUIT FIGURE 2. INPUT CURRENT TEST CIRCUIT VDD 0.1µF ID 500µF Q2 CLK CLK Q3 Q4 Q2 1 24 Q3 2 23 3 22 4 21 5 20 S CL CL CL CL Q4 2kΩ 2kΩ 6 19 7 18 8 17 9 16 10 15 11 14 12 13 Q1 CL 105 CL POWER DISSIPATION PER PACKAGE (µW) Q1 CD4029 CL CL 2kΩ VSS 2kΩ TA = 25oC VDD = 15V 104 10V 10V 103 5V 102 CL = 50pF CL = 15pF 10 102 103 104 105 106 107 SWITCHING FREQUENCY (Hz) CLOSE SWITCH S AFTER APPLYING VDD FIGURE 3. DYNAMIC POWER DISSIPATION TEST CIRCUIT FOR CD22101AND TYPICAL DYNAMIC POWER DISSIPATION AS A FUNCTION OF SWITCHING FREQUENCY 4-200 CD22101, CD22102 Test Circuits and Waveforms (Continued) VDD ON 1 24 2 23 3 22 4 21 5 20 6 19 7 18 8 17 9 16 10 15 11 14 12 13 VIS IL VOS SW 50pF 10kΩ SW = ANY CROSSPOINT STROBE = DATA - IN = VDD VDD VIS 50% 50% 0 tPLH tPHL VDD VOS 50% 50% 0 VSS FIGURE 4. OFF SWITCH INPUT OR OUTPUT LEAKAGE CURRENT TEST CIRCUIT (16 OF 32 SWITCHES) FIGURE 5. PROPAGATION DELAY TIME TEST CIRCUIT AND WAVEFORMS (SIGNAL INPUT TO SIGNAL OUTPUT, SWITCH ON) tW DATA-IN STROBE STROBE 50% VDD SW 1kΩ SW = ANY CROSSPOINT 50% 50% VOS DATA-IN 50% 0 tS VDD VIS tW VDD tS tH tH 0 tPZH 50pF VDD 90% VOS 10% 0 tPHZ FIGURE 6. PROPAGATION DELAY TIME TEST CIRCUIT AND WAVEFORMS (STROBE TO SIGNAL OUTPUT, SWITCH TURN-ON OR TURN-OFF) 4-201 CD22101, CD22102 Test Circuits and Waveforms (Continued) DATA-IN VDD VDD VDD VDD 50% DATA-IN tPZH VOS SW VDD 1kΩ 50pF 0 1kΩ 0 VIS VOS VIS tPZL VOS SW VDD VOS 50pF 10% 0 50% DATA-IN 90% 0 SW = ANY CROSSPOINT STROBE = VDD FIGURE 7. PROPAGATION DELAY TIME TEST CIRCUIT AND WAVEFORMS (DATA-IN TO SIGNAL OUTPUT, SWITCH TURN-ON TO HIGH OR LOW LEVEL) VDD ADDRESS = 0 ADDRESS ADDRESS = 1 50% 50% 50% 0 tS VDD tH VDD VDD DATA-IN VIS SW VOS1 VIS SW 0 VOS2 tPHZ VDD VOS1 1kΩ 50pF 1kΩ 0 50pF VDD VOS2 SW = ANY CROSSPOINT STROBE = VDD 0 FIGURE 8. PROPAGATION DELAY TIME TEST CIRCUIT AND WAVEFORMS (ADDRESS TO SIGNAL OUTPUT, SWITCH TURN-ON OR TURN-OFF) 4-202 tPZH 90% 10% CD22101, CD22102 Test Circuits and Waveforms (Continued) 50% STROBE 50% DATA-IN DATA tSU 50% tHLH tHHL tHLH tH 50% STROBE ADDRESS 1µs 1µs OUTPUT OF SWITCH ADDRESSED 1µs Y2 IF SETUP AND HOLD TIMES PROVIDED ARE TOO SHORT, AN UNADDRESSED SWITCH MAY BE TURNED ON OR OFF SIMULTANEOUSLY WITH THE ADDRESSED SWITCH SET ALL SWITCHES TO OFF INITIALLY APPLY VDD TO ALL X INPUTS AND RETURN ALL Y OUTPUTS TO VSS THROUGH 1kΩ. ADDRESS X1Y2 (ABCD) WITH fIN = 10kHz FIGURE 9. ADDRESS TO STROBE SETUP AND HOLD TIMES FIGURE 10. STROBE TO DATA-IN HOLD TIME tH, FOR CD22101 CONTROLS 5µs VDD SW X (N) 1kΩ CONTROL Y (N) 0 10kΩ 75mV 0 VOS SW = ANY CROSSPOINT FIGURE 11. TEST CIRCUIT AND WAVEFORMS FOR CROSSTALK (CONTROL INPUT TO SIGNAL OUTPUT) -140 TA = 25oC RS = 600Ω RL = 600Ω VIS = 1VRMS = dB -120 600Ω SW OFF 600Ω SW 600Ω VOS CROSSTALK VIS V OS 20 log ---------V IS ON 600Ω SW = ANY CROSSPOINT -100 -80 VDD = 5V -60 10V -40 15V -20 0 102 103 104 105 106 107 INPUT SIGNAL FREQUENCY (Hz) FIGURE 12. TEST CIRCUIT AND TYPICAL CROSSTALK AS A FUNCTION OF FREQUENCY BETWEEN SWITCH CIRCUITS IN THE SAME PACKAGE 4-203 CD22101, CD22102 Test Circuits and Waveforms (Continued) TA = 25oC RS = 600Ω RL = 600Ω VOS 600Ω = 600Ω ANY OFF SWITCH -120 -100 FEEDTHROUGH VIS V OS 20 log ---------V IS dB -140 V OS ISOLATION (dB) = 20 LOG --------V IS 7.5V, -7.5V, 3VRMS 5V, -5V, 2VRMS -80 VDD = 2.5V, VSS = -2.5V -60 VIS = 1VRMS -40 -20 102 103 105 104 106 107 INPUT SIGNAL FREQUENCY (Hz) FIGURE 13. TEST CIRCUIT AND TYPICAL FEEDTHROUGH AS A FUNCTION OF FREQUENCY (ANY OFF SWITCH) Typical Performance Curves VDD = 2.5V, VSS = -2.5V VDD = 5V, VSS = -5V 175 SWITCH “ON” RESISTANCE (Ω) SWITCH “ON” RESISTANCE (Ω) 350 300 250 200 150 100 TA = 125oC 25oC 50 150 125 100 TA = 125oC 75 25oC 50 -55oC 25 -55oC 0 0 -2 -1 0 1 -4 2 INPUT SIGNAL (V) FIGURE 14. TYPICAL ON RESISTANCE AS A FUNCTION OF INPUT SIGNAL VOLTAGE AT VDD = -VSS = 2.5V -2 0 2 4 INPUT SIGNAL (V) FIGURE 15. TYPICAL ON RESISTANCE AS A FUNCTION OF INPUT SIGNAL VOLTAGE AT VDD = -VSS = 5V 4-204 Typical Performance Curves (Continued) 100 400 TA = 25oC 350 TA = 125oC SWITCH “ON” RESISTANCE (Ω) SWITCH “ON” RESISTANCE (Ω) VDD = 7.5V, VSS = -7.5V 75 25oC 50 -55oC 25 300 250 VDD = 2.5V, VSS = -2.5V 200 150 100 ±5V ±7.5V 50 0 0 -10 -8 -6 -4 -2 0 2 6 4 8 -10 10 -5 FIGURE 16. TYPICAL ON RESISTANCE AS A FUNCTION OF INPUT SIGNAL VOLTAGE AT VDD = -VSS = 7.5V TA = 25oC RL = 1MΩ, 100kΩ, 10kΩ 2.5 1kΩ 8 STROBE = VDD 6 DATA-IN = VDD 4 500Ω SW VIS 2 VOS RL VSS 4 6 8 OUTPUT SIGNAL (VOS) RMS (V) OUTPUT VOLTAGE (V) 10 VDD = 5V, VSS = -5V VIS = 5VP-P = SINE WAVE 1.77VRMS 10 2 5 FIGURE 17. TYPICAL ON RESISTANCE AS A FUNCTION OF INPUT SIGNAL VOLTAGE AT TA = 25oC VDD = 10V TA = 25oC 0 0 INPUT SIGNAL (V) INPUT SIGNAL (V) 10 CIOS = 0.4pF RL = 1MΩ VIS fIS 2 VOS (RMS) SW RL 1.5 10kΩ CL 1kΩ 1 RF VOLTMETER BOONTON RADIO MODEL 91-CA OR EQUIV. 0.5 0 105 106 107 108 INPUT SIGNAL FREQUENCY (Hz) INPUT VOLTAGE (V) FIGURE 18. TYPICAL SWITCH ON TRANSFER CHARACTERISTICS (1 OF 16 SWITCHES) CL = 15pF VDATA-IN = 5V FIGURE 19. TYPICAL SWITCH ON FREQUENCY RESPONSE CHARACTERISTICS 4-205