622 Mbps CWDM Single Mode Transceiver C-1xx-622-TDFB(3)-SSC4 Features • SC Duplex Single Mode Transceiver • Industry Standard 1x9 Footprint • Complies with IEEE 802.3 Gigabit Ethernet • Single +3.3V/5V Power Supply • Operating temperature Range 0 to 70ºC • PECL Differential Inputs and Outputs • PECL Signal Detection Output • Wave solderable and Aqueous Washable • Uncooled laser diode with MQW stucture • Complies with Telcordia (Bellcore) GR-468-CORE • 622 Mbps application • CWDM application • RoHS compliance available Absolute Maximum Rating Parameter Symbol Min. Max. Unit Note Power Supply Voltage Vcc 0 6 V C-1xx-622-TDFB-SSC4 Power Supply Voltage Vcc 0 3.6 V C-1xx-622-TDFB3-SSC4 Output Current Iout 0 30 mA Soldering Temperature - - 260 ºC Operating temerature Topr 0 70 ºC 10 seconds on leads only Storage Temperature Tstg -40 85 ºC Symbol Min. Typ. Max. Unit V Recommended Operating Condition Parameter Power Supply Voltage Vcc 4.75 5 5.25 Power Supply Voltage Vcc 3.1 3.3 3.5 V Operating Temperature (Case) Topr 0 - 70 ºC - - 622 - Mbps Data Rate Transmitter Specifications Parameter Symbol Min Typical Max Unit Notes Po -3 - +2 dBm Output Power is coupled into a 9/125 µm single Optical Optical Transmit Power λ λ − 5.5 λ λ + 7.5 nm λ = 1xxx nm ∆λ - - 1 nm -20 dB width Side Mode Suppression Ratio Sr 30 35 - dB CW, Po= 5mW Extinction Ratio ER 9 - - dB Output center Wavelength Output Spectrum Width Output Eye Compliant with IEEE 802.3 Optical Rise Time tr - - 0.26 ns 20% to 80% Values Optical Fall Time tf - - 0.26 ns 20% to 80% Values RIN - - -120 dB/Hz TJ - - 0.27 ns Relative Intensity Noise Total Jitter LUMINENTOIC.COM Measured with 27-1 PRBS 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 1 LUMNDS1892-May1308 Rev A.0 622 Mbps CWDM Single Mode Transceiver C-1xx-622-TDFB(3)-SSC4 Transmitter Specifications Parameter Symbol Min Typical Max Unit ICC - - 260 mA Data Input Current-Low IIL -350 - - µA Data Input Current-High IIH - - 350 µA Notes Electrical Power Supply Current Maximum current is specified at Vcc= Maximum @ maximum temperature Differential Input Voltage VIH-VIL 300 - - mV Data Input Voltage-Low VIL-VCC -2.0 - -1.58 V Data Input Voltage-High VIH-VCC -1.1 - -0.74 V Symbol Min Typical Max Unit Notes - - - -28 dBm Measured with 27-1 PRBS,BER= 10-12 Maximum Input Power Pin -3 - - dBm Signal Detect-Asserted Pa - - -28 dBm Measured on transition: low to high Signal Detect-Deasserted Pd -38 - - dBm Measured on transition: high to low Signal Detect-Hysteresis Pa-Pd 1 - - dB 1100 - 1620 nm Min Typical Max Unit Note These inputs are compatible with 10K, 10KH and 100K ECL and PECL inputs Receiver Specifications Parameter Optical Sensitivity Wavelength of Operation Receiver Specifications Parameter Symbol Electrical ICC - - 100 mA The current excludes the output load current Data Output Voltage-Low VOL -Vcc -2.0 - -1.58 V Data Output Voltage-High VOH- Vcc -1.1 - -0.74 V These outputs are compatible with 10K, 10KH and 100KECL and PECL outputs Signal Detect Output Voltage-Low VSDL-Vcc -2.0 - -1.58 V Signal Detect Output Voltage-High VSDH- Vcc -1.1 - -0.74 V Power Supply Current LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 2 LUMNDS1892-May1308 Rev A.0 622 Mbps CWDM Single Mode Transceiver C-1xx-622-TDFB(3)-SSC4 Connection Diagram 1. (Rx GND) 2. (Rx +) 3. (Rx-) 4. (SD) 5. (Rx Vcc) 6. (Tx Vcc) 7. (TX-) 8. (TX+) 9. (Tx GND) NC Top View NC Receiver Signal Ground Receiver Data Out Receiver Data Out Bar Signal Detect Receiver Power Supply Transmitter Power Supply Transmitter Data In Bar Transmitter Data in Transmitter Signal Ground PIN Symbol 1 RxGND 2 RD+ See recommended circuit schematic 3 RD- See recommended circuit schematic 4 SD 5 RxVcc 6 TxVcc DC power for the transmitter section 7 TD- See recommended circuit schematic 8 Warnings TD+ See recommended circuit schematic 9 LUMINENTOIC.COM Notes Directly connect this pin to the receiver ground plane Active high on this indicates a received optical signal DC power for the receiver section TxGND Directly connect this pin to the transmitter ground plane 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 3 LUMNDS1892-May1308 Rev A.0 622 Mbps CWDM Single Mode Transceiver C-1xx-622-TDFB(3)-SSC4 Recommended Circuit Schematic C-1xx-622-TDFB(3)-SSC4 Tx Vcc C5 Rx Vcc 9 R1 7 8 6 5 4 3 2 1 R3 R9 R5 C6 R7 RD + TD + RD - TD - Tx Vcc SD Rx Vcc R2 R4 Notes +3.3V: R1=R3=R5=R7=R9=130 R2=R4=R6=R8=R10=82 C1=C2=C3=C5=C6=0.1F C4=10F L1=L2=1H No internal connection Transceiver Top view No internal connection R10 R6 R8 L1 Notes +5V: R1=R3=R5=R7=R9=82 R2=R4=R6=R8=R10=130 C1=C2=C3=C5=C6=0.1F C4=10F L1=L2=1H Vcc C3 C1 L2 C4 C2 Rx Vcc Tx Vcc The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals. The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc. A GND plane under the module is required for good EMI and sensitivity performance. LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 4 LUMNDS1892-May1308 Rev A.0 622 Mbps CWDM Single Mode Transceiver C-1xx-622-TDFB(3)-SSC4 Package Diagram LUMINENTOIC.COM Top View Front View Side View Rear View Units: mm 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 5 LUMNDS1892-May1308 Rev A.0 622 Mbps CWDM Single Mode Transceiver C-1xx-622-TDFB(3)-SSC4 Ordering Information Available Options: C-1xx-622-TDFB-SSC4 C-1xx-622-TDFB3-SSC4 C-1xx-622-TDFB-SSC4-G5 C-1xx-622-TDFB3-SSC4-G5 Part numbering Definition: C - 1xx - 622 - TDFB(3) - S SC TxPower Temperature and Package RoHS • Tx Wavelength = 1xx0 nm xx=47,49,51,53,55,57,59,61 • Communication protocol (622 Mbps) 622 = PECL Signal Detection Output • TDFB = +5V Transceiver, DFB TDFB3= +3.3V Transceier, DFB • Single mode fiber • Connector options • Tx Power range 4 = -3 to +2 dBm • Temperature range and package Blank = commercial temperature(0 to 70 ºC), 10.4 mm, Black case • Ordering Information Blank = RoHS non-compliant product G5 = RoHS 5/6-compliant product (lead exemption) LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 6 LUMNDS1892-May1308 Rev A.0 1.25 Gbps CWDM Single Mode Transceiver C-1xx-622-TDFB(3)-SSC4 Warnings Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow guidelines according to proper ESD procedures. Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation. Legal Notice IMPORTANT NOTICE! All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of Sale for further warranty information. LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from such use or sale. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current. © LuminentOIC, Inc. 2003 All rights reserved LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 7 LUMNDS1892-May1308 Rev A.0