AIC AIC1550PPTR Low-noise synchronous pwm step-down dc/dc converter Datasheet

AIC1550
Low-Noise Synchronous PWM Step-Down
DC/DC Converter
DESCRIPTION
FEATURES
95% Efficiency or up
800mA Guaranteed Output Current.
Adjustable Output Voltage from 0.75V to VIN
of a range from +2.5V to 6.5V.
Very Low Quiescent Current: 35µA (Typ.).
Fixed- 500KHz or Adjustable Frequency
Synchronous PWM Operation.
Synchronizable
external
Switching
Frequency up to 1MHz.
Accurate Reference: 0.75V (±2%).
100% Duty Cycle in Dropout.
Low Profile 8-Pin MSOP Package.
APPLICATIONS
The AIC1550 is a low-noise pulse-widthmodulated (PWM) DC-DC step-down converter.
It powers logic circuits in PDAs and small
wireless systems such as cellular phones,
handy-terminals.
The device features an internal synchronous
rectifier for high conversion efficiency. Excellent
noise characteristics and fixed-frequency
operation provide easy post-filtering. The
AIC1550 is ideally suited for Li-ion battery
applications. It is also suitable for +3V or +5V
fixed input applications. The device can operate
in either one of the following four modes.
PDAs.
Digital Still Cameras.
Handy-Terminals.
(1)
Forced PWM mode operates at a
fixed frequency regardless of the
load.
(2)
Synchronizable
PWM
mode
allows the synchronization by
using an external switching
frequency
with
a
minimum
harmonics.
(3)
PWM/PFM Mode extends battery
life by switching to a PFM pulseskipping mode under light loads.
(4)
Shutdown mode sets device to
standby, reducing supply current
to 0.1µA or under.
Cellular Phones.
CPU I/O Supplies.
Cordless Phones.
Notebook Chipset Supplies.
Battery-Operated Devices (4 NiMH/ NiCd or 1
Li-ion Cells).
The AIC1550 can deliver over 800mA output
current. The output voltage can be adjusted
from 0.75V to VIN ranging from +2.5V to +6.5V.
Other features of the AIC1550 include low
quiescent current, low dropout voltage, and a
0.75V reference of ±2% accuracy. It is available
in a space-saving 8-pin MSOP package.
Analog Integrations Corporation
Si-Soft Research Center
DS-1550P-04 010405
3A1, No.1, Li-Hsin Rd. I , Science Park , Hsinchu 300, Taiwan , R.O.C.
TEL: 886-3-5772500
FAX: 886-3-5772510
www.analog.com.tw
1
AIC1550
TYPICAL APPLICATION CIRCUIT
VIN= 2.5V to 6.5V
1
BP
CIN
22µF
CBP
0.1µF
LX
VIN
2 BP
3
SHDN
4
FB
GND 7
SYNC/ 6
MODE
RT
5
VOUT = 1.8V
L1
8
*
6.8µH
D1
SS12
Optional
CF
R1
820K
AIC1550
12P
CO
22µF
R2
560K
CIN: TAIYO YUDEN LMK316F226ZL-T Ceramic capacitor
CO1: TAIYO YUDEN LMK316F226ZL-T Ceramic capacitor
L1: TDK SLF6025-6R8M1R3
D1: GS SS12
* Note: Efficiency can boost 2% to 4% if D1 is connected.
ORDERING INFORMATION
AIC1550XXXX
PACKING TYPE
TR: TAPE & REEL
TB: TUBE
PACKAGING TYPE
O:MSOP8
PIN CONFIGURATION
TOP VIEW
VIN 1
BP 2
SHDN 3
FB 4
8 LX
7 GND
6 SYNC/MODE
5 RT
C: Commercial Degree
P: Lead Free
Example: AIC1550COTR
In MSOP Package & Taping &
Reel Packing Type
AIC1550POTR
In MSOP Lead Free Package &
Taping & Reel Packing Type
2
AIC1550
ABSOLUTE MAXIMUM RATINGS
VIN, BP, SHDN, SYNC/MODE, RT to GND
BP to VIN
-0.3 to +7V
.-0.3 to 0.3V
LX to GND
-0.3 ~ (VIN+0.3V)
FB to GND
-0.3 ~ (VBP+0.3V)
Operating Temperature Range
Junction Temperatrue
Storage Temperature Range
Lead Temperature (Soldering. 10 sec)
-40°C ~ 85°C
125°C
- 65°C ~ 150°C
260°C
Absolute Maximum Ratings are those values beyond which the life of a device may be
Impaired.
TEST CIRCUIT
Refer to Typical Application Circuit.
3
AIC1550
ELECTRICAL CHARACTERISTICS
(VIN=+3.6V, TA=+25°C, SYNC/MODE =GND, SHDN =IN, unless otherwise specified.) (Note1)
PARAMETER
Input Voltage Range
Output Adjustment Range
Feedback Voltage
SYMBOL CONDITIONS
V
VOUT
VREF
VIN
V
VFB
0.735
0.765
V
IFB
P-Channel Current-Limit
+1
%
IOUT = 0 to 800mA
-1.3
%
VFB = 1.4V,
-50
0.01
50
VIN = 3.6V
0.32
0.65
VIN = 2.5V
0.38
VIN = 3.6V
0.32
VIN = 2.5V
0.38
(Note 2)
Threshold
fOSC
SYNC Capture Range
UVLO
VIN rising, typical hysteresis is
85mV
VIH
SHDN , SYNC/MODE, LIM
Logic Input Low
VIL
SHDN , SYNC/MODE, LIM
SYNC/MODE Minimum
Pulse Width
70
µA
0.1
1
µA
-20
0.1
20
µA
400
500
600
KHz
1000
KHz
100
Logic Input High
Logic Input Current
35
500
dutyMAX
SHDN , SYNC/MODE, LIM
High or low
Ω
A
leakage current
VIN = 5.5V, VLX = 0 or 5.5V
Ω
2.1
SHDN = LX = GND, includes LX
LX Leakage Current
0.65
nA
1.5
VFB = 1.4V, LX unconnected
Shutdown Supply Current
Threshold
1
SYNC/MODE = GND,
Quiescent Current
0.75
Duty Cycle = 100% to 23%
N-Channel On-Resistance NRDS(ON) ILX = 100mA
Undervoltage Lockout
UNITS
6.5
P-Channel On-Resistance PRDS(ON) ILX = 100mA
Maximum Duty Cycle
MAX
2.5
Load Regulation
Oscillator Frequency
TYP
VIN
Line Regulation
FB Input Current
MIN
1.9
%
2.0
2.1
2
-1
500
V
V
0.1
0.4
V
1
µA
nS
Note 1: Specifications are production tested at TA=25°C. Specifications over the -40°C to 85°C operating
temperature range are assured by design, characterization and correlation with Statistical
Quality Controls (SQC).
Note 2: Maximum specification is guaranteed by design, not production tested.
4
AIC1550
TYPICAL PERFORMANCE CHARACTERISTICS
(TA=25oC, VIN=3.6V, SYNC/MODE=GND, with Schottky diode D1, unless otherwise noted.)
100
100
VIN=2.1V
80
70
VIN=5.0V
60
VIN=6.5V
VIN=2.3V
80
70
VIN=3.3V
VOUT=1.2V
VOUT=1.5V
40
0.1
1
10
100
0.1
1000
1
Load Current (mA)
(R f
100
1000
t t
i
l
li
ti
i
it)
100
VIN=3.3V
VIN=2.1V
90
90
80
70
Efficiency (%)
Efficiency (%)
100
(Refer to typical application circuit)
(Refer to typical application circuit)
VIN=6.5V
VIN=5.0V
60
50
0.1
80
70
VIN=6.5V
VIN=5.0V
60
50
VOUT=1.8V
VIN=3.3V
VOUT=2.5V
40
1
10
100
40
1000
0.1
1
Load Current (mA)
Fig. 3 Load Current vs. Efficiency (VOUT=1.8V)
Fig. 4
(Refer to typical application circuit)
100
1000
Load Current (mA)
Load Current vs. Efficiency (VOUT=2.5V)
100
VIN=3.6V
VIN=3.6V
90
80
80
Efficiency (%)
90
VIN=4.2V
70
60
50
1
10
100
VIN=6.5V
70
VIN=5.0V
60
VIN=4.2V
50
VOUT=3.0V
0.1
10
(Refer to typical application circuit)
100
Efficiency (%)
10
Load Current (mA)
Fig. 2 Load Current vs. Efficiency (VOUT=1.5V)
Fig. 1 Load Current vs. Efficiency (VOUT=1.2V)
40
VIN=6.5V
VIN=5.0V
60
50
50
40
VIN=2.1V
90
Efficiency (%)
Efficiency (%)
90
1000
40
0.1
1
10
VOUT=3.3V
100
1000
Load Current (mA)
Load Current (mA)
Fig. 5 Load Current vs. Efficiency (VOUT=3.0V)
Fig. 6 Load Current vs. Efficiency (VOUT=3.3V)
(Refer to typical application circuit)
(Refer to typical application circuit)
5
AIC1550
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
0.765
100
W/ Schottky Diode
90
Reference Voltage (V)
Efficiency (%)
80
Wo/ Schottky Diode
70
60
SYNC= VIN
50
40
VOUT=3.0V
30
0.1
1
10
Load Current (mA)
VIN=3.6V
0.760
SYNC= GND
100
0.755
0.750
0.745
0.740
0.735
0.730
0.725
-50
1000
-25
550
50
75
100
125
550
540
VIN=3.6V
530
530
520
Frequency (KHz)
Frequency (KHz)
25
Temperature (°C)
Fig. 8 Reference Voltage vs. Temperature
Fig. 7 Load Current vs. Efficiency (W/ or W/O Schottky Diode)
540
0
510
500
490
480
520
510
500
490
480
470
470
460
460
450
-40
-20
0
20
40
60
80
100
450
120
2.0
Temperature (°C)
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
Supply Voltage (V)
Fig. 10 Frequency vs. Input Voltage
Fig. 9 Oscillator Frequency vs. Temperature
1.82
0.44
0.42
Output Voltage (V)
RDSON (mΩ)
1.80
Main Switch
0.40
0.38
0.36
0.34
0.32
VIN=3.6V
1.78
1.76
0.30
0.28
1.74
Synchronous Switch
0.26
2.0
2.5
3.0
3.5
4.0
4.5
5.0
Supply Voltage (V)
Fig. 11 RDSON vs. Supply Voltage
5.5
6.0
1.72
1
10
100
1000
Load Current (mA)
Fig. 12 Output Voltage vs. Load Current
6
AIC1550
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
300
100
VOUT=1.8V
PWM/PFM
90
80
200
Efficiency (%)
DC Supply Current (μA)
250
SYNC/PWM=IN
150
100
70
PWM
60
50
40
SYNC/PWM=GND
30
VIN=3.6V
VOUT=1.8V
50
20
0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
Supply Voltage (V)
Fig. 13 DC Supply Current vs. Supply Voltage
10
0.1
1
10
Fig. 14
100
1000
Load current (mA)
Efficiency vs. Load current
Operation Frequency (KHz)
1000
900
800
700
600
500
2250
2000
Fig. 15
1500 1250 1000 750
Tuning Resistor RT (kΩ)
1750
500
Operation Frequency vs. Tuning Resistor
VOUT=1.8V;
ILOAD=50mA to 500mA;
SYNC/MODE=IN
Fig. 17 Load Transient Response
250
Fig. 16 Start-up from Shutdown, RLOAD=3Ω
VOUT=1.8V;
ILOAD=50mA to 500mA;
SYNC/MODE=GND
Fig. 18
Load Transient Response
7
AIC1550
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
VIN=3.3V to 5V,
IOUT=1.8V;
ILOAD=200mA to 500mA;
SYNC/MODE=IN
Fig. 19 Line Transient Response
Fig. 20 Short Circuits Protection
VIN=3.6V, VOUT=1.8V, ILOAD=800mA
VOUT
VIN=3.6V; VOUT=1.8V;
ILOAD=500mA
VLX
SYNC/MODE=IN
Fig. 21
Switching Waveform
Fig. 22 Output Ripple voltage
8
AIC1550
BLOCK DIAGRAM
BP
C hip S upply
10
0.75V
REF
C urrent A MP .
SHDN
V IN
V IN
+
X5
-
5
S lope
RT
500K H z
O scillator
Frequency
S YN C
+
S election
P hase
C om pensation
FB
FB
REF
Q1
x1
C urrent Lim it
C om parator
C om pensation
-
E rror
A MP .
Q2
X20
REF
-
PW M
C om parator
+
LX
A ntiS hootT hrough
C ontrol Logic
+
Q3
P W M/P FM
C ontrol
Zero C ross
C om parator
-
REF
+
+
GND
P FM
C om parator
PIN DESCRIPTIONS
PIN 1: VIN-
PIN 2: BP-
Supply Voltage Input ranging from
+2.5V to +6.5V. Bypass with a
22µF capacitor.
Supply Bypass Pin internally
connecting to VIN. Bypass with a
0.1µF capacitor.
Shutdown-Control
PIN 3: SHDN - Active-Low,
Input reducing supply current to
0.1µA in shutdown mode.
PIN 4: FBFeedback Input.
PIN 5: RTFrequency
Adjustable
Pin
connecting to GND through a
resistor to increase frequency.
(Refer to Fig. 15)
PIN 6: SYNC/MODEOscillator Sync and Low-Noise,
Mode-Control Input.
SYNC/MODE = VIN (Forced
PWM Mode)
SYNC/MODE = GND (PWM/PFM
Mode)
An
external
clock
signal
connecting to this pin allows LX
switching synchronization.
PIN 7: GND- Ground.
PIN 8: LX-
Inductor connecting to the Drains
of the Internal Power MOSFETs
9
AIC1550
APPLICATION INFORMATION
Introduction
AIC1550 is a low-noise, pulse-width-modulated
(PWM), DC-DC step-down converter. It features
an internal synchronous rectifier, which eliminates
external Schottky diode. AIC1550 is suitable for
Li-lon battery applications, or can be used at 3V
or 5V fixed input voltage. It operates in one of
following four modes.
(1) Forced PWM mode operates at a
fixed frequency regardless of the
load.
(2) Synchronizable PWM mode allows
the synchronization by using an
external switching frequency with a
minimum harmonics.
(3) PWM/PFM Mode extends battery
life by switching to a PFM pulseskipping mode under light loads.
(4) Shutdown mode sets device to
standby, reducing supply current to
0.1µA or under.
Continuous output current of AIC1550 can be
upward to 800mA and output voltage can be
adjusted from 0.75V to VIN with an input range
from 2.5V to 6.5V by a voltage divider. AIC1550
also features high efficiency, low dropout voltage,
and a 0.75V reference with ±2% accuracy. It is
available in a space-saving 8-pin MSOP package.
Operation
When power on, control logic block detects
SYNC/MODE pin connecting to VIN or GND to
determine operation function and gives a signal to
PWM/PFM control block to determine the proper
comparator (ref. Block Diagram). AIC1550 works
with an internal synchronous rectifier - Q3, to
increase efficiency. When control logic block turns
Q2 on, Q3 will turn off through anti-short-through
block. Similarly, when Q3 is on, Q2 will turn off.
AIC1550 provides current limit function by using a
5Ω resistor. When Q1 turns on, current follows
through the 5Ω resistor. And current amplifier
senses the voltage, which crosses the resistor,
and amplifies it. When the sensed voltage gets
bigger than reference voltage, control logic shuts
the device off.
PWM/PFM Function
When connecting SYNC/MODE pin to VIN, the
device is forced into PWM (Pulse-WidthModulated) mode with constant frequency.
Advantage of constant frequency is easily
reducing noise without complex post-filter. But its
disadvantage is low efficiency at light loading.
Therefore, AIC1550 provides a function to solve
this problem. When connecting SYNC/MODE pin
to GND, device is able to get into PWM/PFM
(Pulse-Frequency-Modulated) modes. Under a
light loading condition, the device turns to PFM
mode, which results in a higher efficiency. PWM
mode is on when heavy loading applies and the
noise is reduced.
Frequency Synchronization
Connecting an external clock signal to
SNYC/MODE pin can control switching frequency.
The acceptable range is from 500kHz to 1MHz.
This mode exhibits low output ripple as well as
low audio noise and reduces RF interference
while providing reasonable low current efficiency.
10
AIC1550
100% Duty Cycle Operation
When the input voltage approaches the output
voltage, the converter continuously turns Q2 on.
In this mode, the output voltage is equal to the
input voltage minus the voltage, which is the drop
across Q2.
If input voltage is very close to output voltage, the
switching mode goes from pure PWM mode to
100% duty cycle operation. During this transient
state mentioned above, large output ripple voltage
will appear on output terminal.
Components Selection
Inductor
The inductor selection depends on the operating
frequency of AIC1550. The internal switching
frequency is 500KHz, and the external
synchronized frequency ranges from 500KHz to
1MHz. A higher frequency allows the uses of
smaller inductor and capacitor values. But, higher
frequency results lower efficiency due to the
internal switching loss.
The ripple current ∆IL interrelates with the
inductor value. A lower inductor value gets a
higher ripple current. Besides, a higher VIN or
VOUT can also get the same result. The inductor
value can be calculated as the following formula.
 V

1
(1)
L=
VOUT 1 − OUT 
(f )(∆IL )
VIN 

Users can define the acceptable ∆IL to gain a
suitable inductor value.
Since AIC1550 can be used in ceramic capacitor
application, the component selection will be
different from the one for the application above.
AIC1550 has a built-in slope compensation, which
acitvates when duty cycle is larger than 0.45. The
slope Ma, 0.27V/μs, has to be larger than half of
M2. M2 is equal to output voltage divided by L1.
The formula of inductor is shown as below:
V
V
OUT = OUT
(2)
2 × Ma 2 × 0.27
Note that output voltage can be defined according
L1 >
to user’s requirement to get a suitable inductor
value.
Output Capacitor
The selection of output capacitor depends on the
suitable ripple voltage. Lower ripple voltage
corresponds to lower ESR (Equivalent Series
Resistor) of output capacitor. Typically, once the
ESR is satisfied with the ripple voltage, the value
of capacitor is adequate for filtering. The formula
of ripple voltage is as below:

1 

(3)
∆VOUT = ∆IL  ESR +
8
fC
OUT 

Besides, in buck converter architecture frequency
stands at 1/√(LC) when a double pole formed by
the inductor and output capcitor occurs. This will
reduce phase margin of circuit so that the stability
gets weakened. Therefore, a feedforward
capacitor that is parallel with R1 can be added to
reduce output ripple voltage and increase circuit
stability. The output capacitor can be calculated
as the following formula.
1
L1 × C
≅
O
1
R1 × CF
(4)
For more reduction in the ripple voltage, a 12pF
ceramic capacitor, which is parallel with output
capacitor, is used.
External Schottky Diode
AIC1550 has an internal synchronous rectifier,
instead of Schottky diode in buck converter.
However, a blank time, which is an interval when
both of main switch, Q2, and synchronous rectifier,
Q3, are off; occurs at each switching cycle. At the
moment, AIC1550 has a decreasing efficiency.
Therefore, an external Schottky diode is needed
to reinforce the efficiency.
11
AIC1550
Since the diode conducts during the off time, the
peak current and voltage of converter is not
allowed to exceed the diode ratings. The ratings
of diode can be calculated by the following
formulas:
VD,MAX( OFF ) = VIN
ID,MAX( ON) = IOUT,MAX +
ID,AVG( ON)
(5)
∆IL
2
(6)
= IOUT − IIN = IOUT − D × IOUT
= (1 − D) × IOUT
(7)
Adjustable Output Voltage
AIC1550 appears a 0.75V reference voltage at FB
pin. Output voltage, ranging from 0.75V to VIN,
can be set by connecting two external resistors,
R1 and R2. VOUT can be calculated as:
R1
(8)
)
VOUT = 0.75 V × (1 +
R2
Applying a 12pF capacitor parallel with R1 can
prevent stray pickup. They should sit as close to
AIC1550 as possible. But load transient response
is degraded by this capacitor.
Layout Consideration
To ensure a proper operation of AIC1550, the
following points should be given attention to:
1. Input capacitor and Vin should be placed as
close as possible to each other to reduce the
input ripple voltage.
2. The output loop, which is consisted of
inductor, Schottky diode and output capacitor,
should be kept as small as possible.
3. The routes with large current should be kept
short and wide.
4. Logically the large current on the converter,
when AIC1550 is on or off, should flow at the
same direction.
5. The FB pin should connect to feedback
resistors directly. And the route should be
away from the noise source, such as inductor
of LX line.
6. Grounding all components at the same point
may effectively reduce the occurrence of loop.
A stability ground plane is very important for
gaining higher efficiency. When a ground
plane is cut apart, it may cause disturbed
signal and noise. If possible, two or three
through-holes can ensure the stability of
grounding. Fig.24 to 27 show the layout
diagrams of AIC1550.
Example
Here are two examples to prove the components
selector guide above.
1. Tantalum capacitors application:
Assume AIC1550 is used for mobile phone
application, which uses 1-cell Li-ion battery with
2.7V to 4.2V input voltage for power source. The
required load current is 800mA, and the output
voltage is 1.8V. Substituting VOUT=1.8V, VIN=4.2V,
∆I=250mA, and f=500KHz to equation (1)
L=
1 .8 V 
1.8 V

1 −
 = 8.23µH
4 .2 V 
500KHz × 250mA 
Therefore, 10µH is proper for the inductor. And
the inductor of series number SLF6025-100M1R0
from TDK with 57.3mΩ series resistor is
recommended for the best efficiency.
For output capacitor, the ESR is more important
than its capacity. Assuming ripple voltage
∆V=100mV, then the ESR can be calculated as:
∆V 100mV
ESR=
=
= 0.4Ω
∆I 250mA
Therefore, a 33µH/10V capacitor, MCM series
from NIPPON, is recommend.
Schottky selection is calculated as following.
VD,MAX( OFF ) = VIN = 4.2V
12
AIC1550
∆IL
2
250mA
= 800mA +
2
= 925mA
VOUT is substituted by 1.8V in equation (2) as
ID,MAX(ON) = IOUT,MAX +
L1 >
Let L1 = 6.8µH, and choose CF = 12pF, R1 =
820kΩ.
ID,avg( ON) = (1 − D) × IOUT
Co calculated by the following formula can
improve circuit stability.
1 .8
) × 800mA
4 .2
= 457 .14mA
= (1 −
1
According the datas above, the Schottky diode,
SS12, from GS is recommend.
For feedback resistors, choose R2=390kΩ and R1
can be calculated as follow:
 1 .8 V

R1 = 
− 1 × 390kΩ = 546kΩ ; use 560kΩ
0
.
75


Fig. 22 shows the application circuit of AIC1550,
and Fig. 23 to 26 show the layout diagrams of it.
Of the same AIC1550 application above, except
for ceramic capacitor used, Co, R1, and R2 can
be calculated as following formulas. And the same
values of load current and output voltage at
800mA and 1.8V respectively are used.
1
BP
+
CIN
10µF
CBP
0.1µF
LX
VIN
2 BP
3
SHDN
4
FB
L1 × C
C
O
GND 7
RT
5
O
1
R1 × CF
2
2
(
(
R1 × CF )
820k × 12pF)
=
=
L1
6.8µ.
= 12 µF
Say, CO is 22µF. Then, R2 can be decided by
equation (8) as
R1
=
VOUT
1.8
−1=
− 1 = 1.4
Vref
0.75
So, R2 = 560kΩ.
Note: Schottky diode, SS12 from GS, is still
required in this application.
VOUT = 1.8V
L1
8
SYNC/ 6
MODE
≅
Therefore,
R2
2. Ceramic capacitors application:
VIN= 2.5V to 6.5V
V
OUT = 1.8 = 3.33 µH
0.54
0.54
10µF
D1
SS12
**
Optional
CF
R1
560K
AIC1550
R2
390K
10P
+
*CO1
33µF
*CO2
4.7µF
* Note: CO1 can be omitted if CO2 in 10µF Ceramic
CIN: NIPPON 10µF/6V Tantalum capacitor
** Note: Efficiency can boost 2% to 4% if D1 is connected.
CO1: NIPPON 33µF/6V Tantalum capacitor
L: TDK SLF6025-100M1R0
D1: GS SS12
Fig. 23 AIC1550 Application Circuit (Tantalum capacitor application)
13
AIC1550
Fig. 24 Top Layer
Fig. 25 Bottom Layer
Fig. 26 Top Over Layer
Fig. 27 Bottom Over Layer
14
AIC1550
PHYSICAL DIMENSIONS
(unit: mm)
MSOP 8
D
S
Y
M
B
O
L
MSOP-8
MILLIMETERS
MIN.
MAX.
E
E1
A
A A
SEE VIEW B
A1
0.05
0.15
A2
0.75
0.95
b
0.25
0.40
c
0.13
0.23
D
2.90
E
A2
e
1.10
E1
2.90
A
e
L
A1
θ
3.10
4.90 BSC
3.10
0.65 BSC
0.40
0.70
0°
6°
b
0.25
c
WITH PLATING
BASE METAL
SECTION A-A
θ
L
VIEW B
Note:
Information provided by AIC is believed to be accurate and reliable. However, we cannot assume responsibility for use of any
circuitry other than circuitry entirely embodied in an AIC product; nor for any infringement of patents or other rights of third
parties that may result from its use. We reserve the right to change the circuitry and specifications without notice.
Life Support Policy: AIC does not authorize any AIC product for use in life support devices and/or systems. Life support devices
or systems are devices or systems which, (I) are intended for surgical implant into the body or (ii) support or sustain life, and
whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably
expected to result in a significant injury to the user.
15
Similar pages