JAN06 (1/5) MITSUBISHI (OPTICAL DEVICES) FU-653SEA-x2MyyF 1.55 μm EAM/DFB-LD MODULE WITH SINGLEMODE FIBER PIGTAIL DESCRIPTION Module type FU-653SEA-x2MyyF is a 1.55μm EA modulator integrated DFB-LD module with singlemode optical fiber. This module is suitable to a light source for use in 10Gb/s digital optical communication systems. FEATURES • Input impedance is 50Ω • Electroabsorption Modulator integrated Multi quantum wells (MQW) DFB Laser Diode Emission wavelength is in full C band Single mode optical fiber pig-tail Built-in optical isolator Built-in thermal electric cooler 7-pin Butterfly package with GPO connectoｒ • • • • • • With photodiode for optical output monitor • RoHS (2002/95/EC) complianｔ APPLICATION STM-64, OC192 (10Gb/s) Dense-WDM systems ABSOLUTE MAXIMUM RATINGS (Tld=Tset) Parameter Symbol Conditions Rating Unit Laser diode Optical output power Pf CW 6 mW Forward current If CW 200 mA Reverse voltage Vrl CW 2 V Modulator Reverse voltage Vrm 5 V Forward voltage Vfm 1 V Photodiode for Reverse voltage Vrd 20 V monitoring Forward current Ifd 2 mA Thermoelectric Current Ipe 1.5 A cooler(Note 1) Voltage Vpe 3 V Operating case temperature Tc -20 to 70 °C Storage temperature Tstg -40 to 85 °C Note 1. Even if the thermoelectric cooler(TEC) is operated within the rated conditions, uncontrolled current loading or operation without heat sink may easily damage the module by exceeding the storage temperature range. Thermistor resistance should be properly monitored by the feedback circuit during TEC operation to avoid the catastrophic damage. Mitsubishi Electric Corporation reserves the right to make changes to the products or information contained herein without notice. No liability is assumed as a result of their use or application. JAN06 (2/5) MITSUBISHI (OPTICAL DEVICES) FU-653SEA-x2MyyF 1.55 μm EAM/DFB-LD MODULE WITH SINGLEMODE FIBER PIGTAIL ELECTRICAL/OPTICAL CHARACTERISTICS (Tc=25°C, Tld=Tset, unless otherwise noted) Item Symbol Condition(Note2) Min. Typ. Max. Unit Threshold current Ith CW,Vm=0V 5 30 mA Operating current Iop CW,Vm=0V 50 70 100 mA Operating voltage Vop CW, If=Iop, Vm=0V 1.7 V Input impedance Zin If=Iop 50 Ω Optical output power Pf (Note 3,4) -2 dBm from fiber end Laser diode Tset 15 35 °C temperature Wavelength (Note 3,4) (See teble 1) nm λc Side mode Sr (Note 3,4) 35 40 dB suppression ratio Relative intensity RIN CW, If=Iop, Vm=0V,10GHz -135 dB/Hz noise Power penalty Pp (Note 3,4,), 800ps/nm 2.0 dB Extinction ratio Ex (Note 3,4) 10 dB Rise/fall time tr/tf (Note 3,4),20-80% 45 ps Cutoff frequency fc If=Iop,Vm=-1V 11 GHz RF return loss S11 10 15 dB If=Iop,Vm=-1V, f≤5GHz 5 7 dB If=Iop,Vm=-1V, f≤10GHz Tracking error Er 0.3 0.5 dB If=Iop,Tc=-20∼70°C, Note 5 Monitor current Imon If=Iop,Vrd=-5V 0.1 1.5 mA Dark current(PD) Id Vrd=-5V 0.1 μA Capacitance(PD) Ct Vrd=-5V 10 pF Optical isolation Iso 35 dB Tc=25°C 23 dB Tc=-20∼70°C Note 2 : Vm is EAM bias voltage at CW condition, Vpp and Voff are EAM amplitude and EAM high level offset voltage respectively at modulation condition. Note 3 : 9.95328Gbps, NRZ, PRBS2^23-1, If=Iop,Vpp=2.5V,Voff=0V to –1V Note 4 : Optical return loss of the connectors should be greater than 40dB in order to get specified performance. Note 5 : Er=10×log[Pf(Tc)/Pf(25°C)] THERMAL CHARACTERISTICS Parameter Thermistor resistance B constant of Rth Cooling capacity Cooler current Cooler voltage Symbol Rth B ΔT Ipe Vpe FIBER PIGTAIL SPECIFICATIONS Parameter Type Mode field diameter Cladding diameter Secondary coating outer diameter Connector Optical return loss of connector Conditions (Note2) Tc=Tld=25°C, If=Iop, Tc=70°C,Tld=25°C If=Iop, Tc=70°C,Tld=25°C Specification SM 9.5±1 125±2 0.9±0.1 See ordering information 40(min) Min. 9.5 55 - Limits Typ. 10 3950 0.6 1.2 Max. 10.5 1.2 2.5 Unit Ω K °C A V Unit μm μm mm dB Mitsubishi Electric Corporation reserves the right to make changes to the products or information contained herein without notice. No liability is assumed as a result of their use or application. JAN06 (3/5) MITSUBISHI (OPTICAL DEVICES) FU-653SEA-x2MyyF 1.55 μm EAM/DFB-LD MODULE WITH SINGLEMODE FIBER PIGTAIL ORDERING INFORMATION FU – 653SEA – _2M __ F λ code W V Table 1. f [THz] 195.90 195.80 195.70 195.60 195.50 195.40 195.30 195.20 195.10 195.00 194.90 194.80 194.70 194.60 λc [nm] 1530.33 1531.12 1531.90 1532.68 1533.47 1534.25 1535.04 1535.82 1536.61 1537.40 1538.19 1538.98 1539.77 1540.56 See table 1 Connector SC/PC FC/PC λ code 11 13 15 17 19 21 23 25 27 29 31 33 35 37 f [THz] 194.50 194.40 194.30 194.20 194.10 194.00 193.90 193.80 193.70 193.60 193.50 193.40 193.30 193.20 λc [nm] 1541.35 1542.14 1542.94 1543.73 1544.53 1545.32 1546.12 1546.92 1547.72 1548.51 1549.32 1550.12 1550.92 1551.72 λ code 39 41 43 45 47 49 51 53 55 57 59 61 63 65 f [THz] 193.10 193.00 192.90 192.80 192.70 192.60 192.50 192.40 192.30 192.20 192.10 192.00 191.90 191.80 λc [nm] 1552.52 1553.33 1554.13 1554.94 1555.75 1556.55 1557.36 1558.17 1558.98 1559.79 1560.61 1561.42 1562.23 1563.05 λ code 67 69 71 73 75 77 79 81 83 85 87 89 91 93 All wavelengths are referred to vacuum. Tolerance is λc+/-0.05nm. Mitsubishi Electric Corporation reserves the right to make changes to the products or information contained herein without notice. No liability is assumed as a result of their use or application. JAN06 (4/5) MITSUBISHI (OPTICAL DEVICES) FU-653SEA-x2MyyF 1.55 μm EAM/DFB-LD MODULE WITH SINGLEMODE FIBER PIGTAIL OUTLINE DIAGRAM unit : mm Connector Pin7 Pin1 Thermistor Thermo cooler PD EAM/LD GPO connector Pin No. 1 2 3 4 5 6 7 Case Function Thermistor Thermistor LD bias (Anode) Monitor PD (Anode) Monitor PD (Cathode) Cooler (Anode) Cooler (Cathode) Ground FU-653SEA-x2MｙｙF Mitsubishi Electric Corporation reserves the right to make changes to the products or information contained herein without notice. No liability is assumed as a result of their use or application. JAN06 (5/5) MITSUBISHI (OPTICAL DEVICES) FU-653SEA-x2MyyF 1.55 μm EAM/DFB-LD MODULE WITH SINGLEMODE FIBER PIGTAIL Safety Cautions for Use of Optoelectronic Devices General: Although the manufacturer is always striving to improve the reliability of its product, problems and errors may occur with semiconductor products. Therefore, the user's products are required to be designed with full safety regard to prevent any accidents that results in injury, death, fire or environmental damage even when semiconductor products happen to error. Especially it is recommended to take in consideration about redundancy, fire prevention, error prevention safeguards. And the following requirements must be strictly observed. Warning! 1. Eye safety : Seminductor laser radiates laser light during operation. Laser light is very dangerous when shot directly into human eyes. Don't look at laser light directly, or through optics such as a lens. The laser light should be observed using the ITV camera, IRviewer, or other appropriate instruments. 2. Product handling : The product contains GaAs (gallium arsenide). It is safe for regular use, but harmful to the human body if made into powder or steam. Be sure to avoid dangerous process like smashing, burning, chemical etching. Never put this product in one's mouth or swallow it. 3. Product disposal : This product must be disposed of as special industrial waste. It is necessary to separate it from general industrial waste and general garbage. Handling Cautions for Optoelectronic Devices 1. General: (1) The products described in this specification are designed and manufactured for use in general communication systems or electronic devices, unless their applications or reliability are otherwise specified. Therefore, they are not designed or manufactured for installation in devices or systems that may affect human life or that are used in social infrastructure requiring high reliability. (2) When the customer is considering to use the products in special applications, such as transportation systems (automobiles, trains, vessels), medical equipments, aerospace, nuclear power control, and submarine repeaters or systems, please contact Mitsubishi Electric or an authorized distributor. 2. Shipping Conditions: (1) During shipment, place the packing boxes in the correct direction, and fix them firmly to keep them immovable. Placing the boxes upside down, tilting, or applying abnormal pressure onto them may cause deformation in the electrode terminals, breaking of optical fiber, or other problems. (2) Never throw or drop the packing boxes. Hard impact on the boxes may cause break of the devices. (3) Take strict precautions to keep the devices dry when shipping under rain or snow. 3. Storage Conditions: When storing the products, it is recommended to store them following the conditions described below without opening the packing. Not taking enough care in storing may result in defects in electrical characteristics, soldering quality, visual appearance, and so on. The main points are described below (if special storage conditions are given to the product in the specification sheet, they have priority over the following general cautions): (1) Appropriate temperature and humidity conditions, i.e., temperature range between 5~30°C, and humidity between 40~60 percent RH, should be maintained in storage locations. Controlling the temperature and humidity within this range is particularly important in case of long-term storage for six months or more. (2) The atmosphere should be particularly free from toxic gases and dust. (3) Do not apply any load on the product. (4) Do not cut or bend the leads of the devices which are to be stored. This is to prevent corrosion in the cut or bent part of the lead causing soldering problems in the customer’s assembling process. (5) Sudden change in temperature may cause condensation in the product or packing, therefore, such locations should be avoided for storing. Temperature in storage locations should be stable. (6) When storing ceramic package products for extended periods of time, the leads may turn reddish due to reaction with sulfur in the atmosphere. (7) Storage conditions for bare chip and unsealed products shall be stated separately because bare chip and unsealed products require stricter controls than package sealed products. 4. Design Conditions and Environment under Use: (1) Avoid use in locations where water or organic solvents adhere directly to the product, or where there is any possibility of the generation of corrosive gas, explosive gas, dust, salinity, or other troublesome conditions. Such environments will not only significantly lower the reliability, but also may lead to serious accidents. (2) Operation in excess of the absolute maximum ratings can cause permanent damage to the device. The customers are requested to design not to exceed those ratings even for a short time. 5. ESD Safety Cautions: The optoelectronic devices are sensitive to static electricity (ESD, electro-static discharge). The product can be broken by ESD. When handling this product, please observe the following countermeasures: <Countermeasures against Static Electricity and Surge> To prevent break of devices by static electricity or surge, please adopt the following countermeasures in the assembly line: (1) Ground all equipments, machinery jigs, and tools in the process line with earth wires installed in them. Take particular care with hot plates, solder irons and other items for which the commercial power supplies are prone to leakage. (2) Workers should always use earth bands. Use of antistatic clothing, electric conductive shoes, and other safety equipment while at work is highly recommended. (3) Use conductive materials for this product’s container, etc. (4) It is recommended that grounding mats be placed on the surfaces of assembly line workbench and the surrounding floor in work area, etc. (5) When mounting this product in parts or materials which can be electrically charged (printed wiring boards, plastic products, etc.), pay close attention to the static electricity in those parts. ESD may damage the product. (6) Humidity in working environment should be controlled to be 40 percent RH or higher. These countermeasures are most general, and there is a need to carefully confirm the line before starting mass production using this product (in the trial production, etc.). It is extremely important to prevent surge, eliminate it rapidly, and prevent it from spreading. Mitsubishi Electric Corporation reserves the right to make changes to the products or information contained herein without notice. No liability is assumed as a result of their use or application.