MOLDED WIREWOUND CHIP INDUCTORS HWI453232 SERIES 1. PART NO. EXPRESSION : HW I 4 5 3 2 3 2 - 1 R 0 K F (a) (b) (c) (d)(e) (a) Series code (d) Tolerance code : K = ±10%, M = ±20% (b) Dimension code (e) F : Lead Free (c) Inductance code : 1R0 = 1.00uH 2. CONFIGURATION & DIMENSIONS : A' 1R0 A G I F H C I F PCB Pattern E B Unit:m/m A' A B C E F G H I 4.5±0.3 4.2±0.2 3.2±0.2 3.2±0.2 1.2±0.2 1.0±0.2 2.2 Ref. 1.6 Ref. 1.5 Ref. 3. SCHEMATIC : 4. MATERIALS : (a) Core : DR Ferrite Core d (b) Wire : Enamelled Copper Wire a (c) Terminal : Tinned Copper Plate (d) Capsulate : Epoxy Novolac Molding Compound c b NOTE : Specifications subject to change without notice. Please check our website for latest information. 26.02.2009 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 1 MOLDED WIREWOUND CHIP INDUCTORS HWI453232 SERIES 5. GENERAL SPECIFICATION : a) Temp. rise : 20°C Max. b) Ambient temp. : 100°C Max. c) Storage temp. : -40°C to +125°C d) Operating temp. : -40°C to +125°C e) Terminal strength : 0.5Kg Min. f) Rated current : Current cause inductance drop within 10% g) Resistance to solder heat : 260°C for 10secs h) Resistance to solvent : Per MIL-STD-202F 6. CHARACTERISTICS CURVES : Temperature (°C) Peak Temp : 250°C Max. Max time above 230°C : 40sec Max. Max time above 200°C : 70sec Max. Temperature Rising Area Preheat Area Reflow Area Cooling Area 2~4°C/sec 150~180°C / 90~150 sec 2~4°C/sec 3~5°C/sec 250 250±5°C 10sec 200 (45~70sec) 150 100 50 0 50 100 150 200 250 Time (seconds) NOTE : Specifications subject to change without notice. Please check our website for latest information. 26.02.2009 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 2 MOLDED WIREWOUND CHIP INDUCTORS HWI453232 SERIES 7. ELECTRICAL CHARACTERISTICS : Inductance ( µH ) Part No. Q Min. Test Frequency ( MHz ) SRF ( MHz ) Min. RDC (ȍ) Max. IDC ( mA ) Max. HWI453232-1R0 F 1.00 10 7.96 180 0.11 1050 HWI453232-1R2 F 1.20 10 7.96 160 0.12 1000 HWI453232-1R5 F 1.50 10 7.96 130 0.15 950 HWI453232-1R8 F 1.80 10 7.96 100 0.16 900 HWI453232-2R2 F 2.20 10 7.96 80 0.18 850 HWI453232-2R7 F 2.70 10 7.96 60 0.20 800 HWI453232-3R3 F 3.30 10 7.96 45 0.22 750 HWI453232-3R9 F 3.90 10 7.96 40 0.24 700 HWI453232-4R7 F 4.70 10 7.96 35 0.27 650 HWI453232-5R6 F 5.60 10 7.96 30 0.30 650 HWI453232-6R8 F 6.80 10 7.96 28 0.35 600 HWI453232-8R2 F 8.20 10 7.96 25 0.40 600 HWI453232-100 F 10.00 10 2.52 22 0.50 550 HWI453232-120 F 12.00 10 2.52 21 0.60 500 HWI453232-150 F 15.00 10 2.52 20 0.70 450 HWI453232-180 F 18.00 10 2.52 19 0.80 400 HWI453232-220 F 22.00 10 2.52 18 0.90 370 HWI453232-270 F 27.00 10 2.52 16 1.20 330 HWI453232-330 F 33.00 10 2.52 14 1.40 300 HWI453232-390 F 39.00 10 2.52 12 1.60 280 HWI453232-470 F 47.00 10 2.52 11.5 1.90 260 HWI453232-560 F 56.00 10 2.52 11 2.20 240 HWI453232-680 F 68.00 10 2.52 10 2.60 220 HWI453232-820 F 82.00 10 2.52 9 3.50 200 HWI453232-101 F 100.00 20 0.796 8 4.00 180 HWI453232-121 F 120.00 20 0.796 7.5 4.50 160 HWI453232-151 F 150.00 20 0.796 7.0 6.50 140 HWI453232-181 F 180.00 20 0.796 6.5 7.50 120 HWI453232-221 F 220.00 20 0.796 5.5 9.00 120 HWI453232-271 F 270.00 20 0.796 5.0 11.0 100 90 HWI453232-331 F 330.00 20 0.796 4.0 13.0 HWI453232-391 F 390.00 30 0.796 3.0 13.5 85 HWI453232-471 F 470.00 30 0.796 3.0 15.0 75 HWI453232-561 F 560.00 30 0.796 3.0 17.0 70 HWI453232-681 F 680.00 30 0.796 2.5 22.8 65 Inductance tolerance : : K : ±10% M : ±20% NOTE : Specifications subject to change without notice. Please check our website for latest information. 26.02.2009 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 3 MOLDED WIREWOUND CHIP INDUCTORS HWI453232 SERIES 8. PACKAGING INFORMATION : ( 1 ) CONFIGURATION T COVER TAPE B ØC A N 2.0±0.5 ØC D G EMBOSSED CARRIER * CARRIER TAPE WIDTH : D TRAILER NO COMPONENT 160mm Min. 1R0 1R0 START 1R0 1R0 1R0 4 m/m 1R0 P:8 m/m END TRAILER NO COMPONENT 390mm Min. COMPONENTS USER DIRECTION OF FEED ( 2 ) DIMENSIONS Unit:m/m A B C D 178 21±0.8 13 12 G 14 +0 N 50 -0 T 16.5 NOTE : Specifications subject to change without notice. Please check our website for latest information. 26.02.2009 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 4 MOLDED WIREWOUND CHIP INDUCTORS HWI453232 SERIES 9. RELIABILTY TEST : TEST ITEM SPECIFICATION TEST CONDITION / TEST METHOD ELECTRICAL PERFORMANCE TEST INDUCTANCE L HP4194A, Q HPE4991A, HP4285A IMPEDANCE ANALYZER : SELF RESONANCE FREQUENCY SRF DIGITAL MULITMETER : HPE4991A REFER TO STANDARD ELECTRICAL DC RESISTANCE RDC HP4194A, 502BC CHARACTERISTIC LIST APPLIED THE CURRENT TO COILS, THE INDUCTANCE CHANGE SHALL BE LESS THAN 10% TO INITIAL VALUE & TEMPERATURE RISE SHALL RATED CURRENT IDC NOT BE MORE THAN 20°C 1. APPLIED THE ALLOWED DC CURRENT FOR TEMPERATURE 20°C MAX RISE TEST 10 MINUTES 2. TEMPERATURE MEASURE BY DIGITAL SURFACE THERMOMETER AFTER TEST, INDUCTORS SHALL BE NO EVIDENCE OVER LOAD TEST OF ELECTRICAL AND MECHANICAL DAMAGE APPLIED 2 TIMES OF RATED ALLOWED DC CURRENT TO INDUCTOR FOR A PERIOD OF 5 MINUTES AFTER TEST, INDUCTORS WITHSTANDING SHALL BE NO EVIDENCE AC VOLTAGE OF 1000VAC APPLIED BETWEEN VOLTAGE TEST OF ELECTRICAL AND INDUCTORS TERMINAL AND CASE FOR 5 MINUTES MECHANICAL DAMAGE INSULATION RESISTANCE TEST 1000 MOHM MIN. 100 VDC APPLIED BETWEEN INDUCTOR TERMINAL AND COATING MECHANICAL PERFORMANCE TEST 1. INDUCTORS SHALL BE 1. AMPLITUDE :1.5 m/m VIBRATION TEST NO EVIDENCE OF 2. FFREQUENCY :10 -- 55 -- 10 HZ / 1MIN ( LOW FREQUENCY ) ELECTRICAL AND 3. DIRECTION :X, Y, Z MECHANICAL DAMAGE 4. DURATION :2 HRS / X, Y, Z 2. INDUCTANCE SHALL SHOCK TEST NOT CHANGE MORE THAN ±5% RESISTANCE TO SOLDERING HEAT 3. Q SHALL NOT CHANGE MORE THAN ±20% INDUCTORS SHALL BE DROPPED 10 TIMES FROM A HEIGHT OF 1m ONTO 3cm WOODEN BOARD TEMP :260±5°C TIME :10±1.0 SEC NOTE : Specifications subject to change without notice. Please check our website for latest information. 26.02.2009 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 5 MOLDED WIREWOUND CHIP INDUCTORS HWI453232 SERIES 9. RELIABILTY TEST : TERMINAL TERMINAL SHALL NOT STRENGTH-PULL BE LOOSENED OR TERMINALS IN THE AXIS DIRECTION FOR TEST RUPTURED 1 MINUTE. THE TERMINAL SHALL AFTER FLUXING, INDUCTOR SHALL BE DIPPED IN BE AT LEAST 90% A MELTED SOLDER BATH AT 240±5°C FOR COVERED WITH SOLDER 5 SECONDS. SOLDERABILITY TEST A 0.5KG LOAD SHALL BE APPLIED TO BOTH THERE SHALL BE NO CASE DEFORMATION RESISTANCE TO CHANGE IN SOLVENT TEST APPEARANCE OR MIL-STD-202F, METHOD 215D OBLITERATION OF MARKING CLIMATIC TEST TEMPERATURE 1. INDUCTORS SHALL BE CHARACTERISTIC NO EVIDENCE OF ELECTRICAL AND MECHANICAL HUMIDITY TEST DAMAGE 2. INDUCTANCE SHALL COLD TEST 1. TEMP :40±2°C 2. R.H. :90 ----- 95% 3. TIME :96±2 HOURS NOT CHANGE MORE 1. TEMP :-25±2°C THAN ±10% 2. TIME :96±2 HOURS 3. Q SHALL NOT CHANGE MORE THAN ±20% THERMAL SHOCK -40°C ----- +125°C TEST ROOM TEMP -40±2°C 15 MINS 30 MINS ROOM TEMP 15 MINS +125±2°C 30 MINS TOTAL :5 CYCLES 1. TEMP :85±2°C DRY HEAT TEST 2. TIME :96±2 HOURS 1. TEMP :85±2°C HIGH TEMPERATURE 2. TIME :1000±12 HOURS LOAD LIFE TEST HUMIDITY LOAD LIFE THERE SHALL BE NO 3. LOAD :ALLOWED DC CURRENT EVIDENCE OF SHORT OR 1. TEMP :40±2°C OPEN CIRCUITING 2. R.H. :90 ----- 95% 3. TIME :1000±12 HOURS 4. LOAD :ALLOWED DC CURRENT Note : Unless otherwise specified, allow the specimen to stand at room temperature for 1 hour or more but more than 2 hours, measure the electrical and mechanical performances NOTE : Specifications subject to change without notice. Please check our website for latest information. 26.02.2009 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 6