Differential/Single-Ended Input, Dual 1 MSPS, 12-Bit, 3-Channel SAR ADC AD7265 FEATURES FUNCTIONAL BLOCK DIAGRAM REF SELECT The conversion process and data acquisition use standard control inputs allowing easy interfacing to microprocessors or DSPs. The input signal is sampled on the falling edge of CS; conversion is also initiated at this point. The conversion time is determined by the SCLK frequency. The AD7265 uses advanced design techniques to achieve very low power dissipation at high throughput rates. With 5 V supplies and a 1 MSPS throughput rate, the part consumes 4 mA maximum. The part also offers flexible power/throughput rate management when operating in normal mode, because the quiescent current consumption is so low. The analog input range for the part can be selected to be a 0 V to VREF (or 2 × VREF) range, with either straight binary or twos complement output coding. The AD7265 has an on-chip 2.5 V reference that can be overdriven when an external reference is preferred. This external reference range is 100 mV to VDD. The AD7265 is available in 32-lead LFCSP and 32-lead TQFP. REF BUF MUX T/H AVDD DVDD AD7265 VA1 VA2 VA3 VA4 12-BIT SUCCESSIVE APPROXIMATION ADC OUTPUT DRIVERS VA5 CONTROL LOGIC VB1 VB2 VB3 VB4 DOUTA SCLK CS RANGE SGL/DIFF A0 A1 A2 VA6 VDRIVE MUX T/H VB5 12-BIT SUCCESSIVE APPROXIMATION ADC OUTPUT DRIVERS DOUTB VB6 BUF AGND AGND AGND DCAPB GENERAL DESCRIPTION The AD7265 1 is a dual, 12-bit, high speed, low power, successive approximation ADC that operates from a single 2.7 V to 5.25 V power supply and features throughput rates of up to 1 MSPS. The device contains two ADCs, each preceded by a 3-channel multiplexer, and a low noise, wide bandwidth track-and-hold amplifier that can handle input frequencies in excess of 30 MHz. DCAPA DGND DGND 04674-001 Dual 12-bit, 3-channel ADC Throughput rate: 1 MSPS Specified for VDD of 2.7 V to 5.25 V Power consumption 7 mW at 1 MSPS with 3 V supplies 17 mW at 1 MSPS with 5 V supplies Pin-configurable analog inputs 12-channel single-ended inputs 6-channel fully differential inputs 6-channel pseudo differential inputs 70 dB SINAD at 50 kHz input frequency Accurate on-chip reference: 2.5 V ±0.2% maximum @ 25°C, 20 ppm/°C maximum Dual conversion with read 875 ns, 16 MHz SCLK High speed serial interface SPI®-/QSPI™-/MICROWIRE™-/DSP-compatible −40°C to +125°C operation Shutdown mode: 1 μA maximum 32-lead LFCSP and 32-lead TQFP 2 MSPS version, AD7266 Figure 1. PRODUCT HIGHLIGHTS 1. Two Complete ADC Functions Allow Simultaneous Sampling and Conversion of Two Channels. Each ADC has three fully/pseudo differential pairs, or six single-ended channels, as programmed. The conversion result of both channels is simultaneously available on separate data lines, or in succession on one data line if only one serial port is available. 2. High Throughput with Low Power Consumption. The AD7265 offers a 1 MSPS throughput rate with 9 mW maximum power dissipation when operating at 3 V. 3. The AD7265 offers both a standard 0 V to VREF input range and a 2 × VREF input range. 4. No Pipeline Delay. The part features two standard successive approximation ADCs with accurate control of the sampling instant via a CS input and once off conversion control. 1 Protected by U.S. Patent No. 6,681,332. Rev. A Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 ©2006 Analog Devices, Inc. All rights reserved. AD7265 TABLE OF CONTENTS Features .............................................................................................. 1 Digital Inputs .............................................................................. 18 General Description ......................................................................... 1 VDRIVE ............................................................................................ 18 Functional Block Diagram .............................................................. 1 Modes of Operation ....................................................................... 19 Product Highlights ........................................................................... 1 Normal Mode.............................................................................. 19 Revision History ............................................................................... 2 Partial Power-Down Mode ....................................................... 19 Specifications..................................................................................... 3 Full Power-Down Mode ............................................................ 20 Timing Specifications .................................................................. 5 Power-Up Times......................................................................... 21 Absolute Maximum Ratings............................................................ 6 Power vs. Throughput Rate....................................................... 21 ESD Caution.................................................................................. 6 Serial Interface ................................................................................ 22 Pin Configurations and Function Descriptions ........................... 7 Microprocessor Interfacing........................................................... 23 Typical Performance Characteristics ............................................. 9 AD7265 to ADSP218x ............................................................... 23 Terminology .................................................................................... 11 AD7265 to ADSP-BF53x ........................................................... 24 Theory of Operation ...................................................................... 13 AD7265 to TMS320C541 .......................................................... 24 Circuit Information.................................................................... 13 AD7265 to DSP563xx ................................................................ 25 Converter Operation.................................................................. 13 Application Hints ........................................................................... 26 Analog Input Structure.............................................................. 13 Grounding and Layout .............................................................. 26 Analog Inputs.............................................................................. 14 PCB Design Guidelines for LFCSP .......................................... 26 Analog Input Selection .............................................................. 17 Evaluating the AD7265 Performance ...................................... 26 Output Coding............................................................................ 17 Outline Dimensions ....................................................................... 27 Transfer Functions...................................................................... 18 Ordering Guide .......................................................................... 27 REVISION HISTORY 11/06—Rev. 0 to Rev. A Changes to Format .............................................................Universal Changes to Reference Input/Output Section ................................ 4 Changes to Table 4............................................................................ 7 Changes to Terminology Section.................................................. 11 Changes to Figure 24 and Differential Mode Section................ 15 Changes to Figure 29...................................................................... 16 Changes to AD7265 to ADSP-BF53x Section............................. 24 Updated Outline Dimensions ....................................................... 27 Changes to Ordering Guide .......................................................... 27 4/05—Revision 0: Initial Version Rev. A | Page 2 of 28 AD7265 SPECIFICATIONS TA = TMIN to TMAX, VDD = 2.7 V to 5.25 V, fSCLK = 16 MHz, fS = 1 MSPS, VDRIVE = 2.7 V to 5.25 V; specifications apply using internal reference or external reference = 2.5 V ± 1%, unless otherwise noted. 1 Table 1. Parameter DYNAMIC PERFORMANCE Specification Unit Test Conditions/Comments Signal-to-Noise Ratio (SNR) 2 71 69 dB min dB min Signal-to-Noise + Distortion Ratio (SINAD)2 70 68 dB min dB min Total Harmonic Distortion (THD)2 –77 –73 dB max dB max –75 dB max fIN = 50 kHz sine wave; differential mode fIN = 50 kHz sine wave; single-ended and pseudo differential modes fIN = 50 kHz sine wave; differential mode fIN = 50 kHz sine wave; single-ended and pseudo differential modes fIN = 50 kHz sine wave; differential mode fIN = 50 kHz sine wave; single-ended and pseudo differential modes fIN = 50 kHz sine wave fa = 30 kHz, fb = 50 kHz –88 –88 –88 dB typ dB typ dB typ 11 50 200 33/26 3.5/3 ns max ps typ ps max MHz typ MHz typ 12 ±1 ±1.5 Bits LSB max LSB max ±0.99 −0.99/+1.5 LSB max LSB max ±6 ±2 ±2.5 ±0.5 LSB max LSB typ LSB max LSB typ ±2 ±0.5 ±5 ±1 ±2 ±0.5 LSB max LSB typ LSB max LSB typ LSB max LSB typ 0 V to VREF 0 V to 2 × VREF 0 to VREF 2 × VREF VCM ± VREF/2 VCM ± VREF V Spurious-Free Dynamic Range (SFDR)2 Intermodulation Distortion (IMD)2 Second-Order Terms Third-Order Terms Channel-to-Channel Isolation SAMPLE AND HOLD Aperture Delay 3 Aperture Jitter3 Aperture Delay Matching3 Full Power Bandwidth DC ACCURACY Resolution Integral Nonlinearity2 Differential Nonlinearity2, 4 Straight Binary Output Coding Offset Error Offset Error Match Gain Error Gain Error Match Twos Complement Output Coding Positive Gain Error Positive Gain Error Match Zero Code Error Zero Code Error Match Negative Gain Error Negative Gain Error Match ANALOG INPUT 5 Single-Ended Input Range @ 3 dB, VDD = 5 V/VDD = 3 V @ 0.1 dB, VDD = 5 V/VDD = 3 V ±0.5 LSB typ; differential mode ±0.5 LSB typ; single-ended and pseudo differential modes Differential mode Single-ended and pseudo differential modes T Pseudo Differential Input Range: VIN+ − VIN− 6 Fully Differential Input Range: VIN+ and VIN− VIN+ and VIN− V V V V Rev. A | Page 3 of 28 RANGE pin low RANGE pin high RANGE pin low RANGE pin high VCM = common-mode voltage 7 = VREF/2 VCM = VREF AD7265 Parameter DC Leakage Current Input Capacitance REFERENCE INPUT/OUTPUT Reference Output Voltage 8 Long-Term Stability Output Voltage Hysteresis2 Reference Input Voltage Range DC Leakage Current Input Capacitance DCAPA, DCAPB Output Impedance Reference Temperature Coefficient VREF Noise LOGIC INPUTS Input High Voltage, VINH Input Low Voltage, VINL Input Current, IIN Input Capacitance, CIN3 LOGIC OUTPUTS Output High Voltage, VOH Output Low Voltage, VOL Floating State Leakage Current Floating State Output Capacitance3 Output Coding CONVERSION RATE Conversion Time Track-and-Hold Acquisition Time3 Throughput Rate POWER REQUIREMENTS VDD VDRIVE IDD Normal Mode (Static) Operational, fS = 1 MSPS fS = 1 MSPS Partial Power-Down Mode Full Power-Down Mode (VDD) Power Dissipation Normal Mode (Operational) Partial Power-Down (Static) Full Power-Down (Static) Specification ±1 45 10 Unit μA max pF typ pF typ 2.5 150 50 0.1/VDD ±2 25 10 20 10 20 V min/V max ppm typ ppm typ V min/V max μA max pF typ Ω typ ppm/°C max ppm/°C typ μV rms typ 2.8 0.4 ±15 5 V min V max nA typ pF typ VDRIVE − 0.2 V min 0.4 V max ±1 μA max 7 pF typ Straight (natural) binary Twos complement Test Conditions/Comments When in track When in hold ±0.2% max @ 25°C For 1000 hours See Typical Performance Characteristics section External reference applied to Pin DCAPA/Pin DCAPB VIN = 0 V or VDRIVE SGL/DIFF = 1 with 0 V to VREF range selected SGL/DIFF = 0; SGL/DIFF = 1 with 0 V to 2 × VREF range 14 90 110 1 SCLK cycles ns max ns max MSPS max 2.7/5.25 2.7/5.25 V min/V max V min/V max 2.3 4 3.2 500 1 2.8 mA max mA max mA max μA max μA max μA max Digital I/Ps = 0 V or VDRIVE VDD = 5.25 V VDD = 5.25 V; 3.5 mA typ VDD = 3.6 V; 2.7 mA typ Static TA = −40°C to +85°C TA > 85°C to 125°C 21 2.625 5.25 mW max mW max μW max VDD = 5.25 V VDD = 5.25 V VDD = 5.25 V, TA = −40°C to +85°C 1 Temperature range is −40°C to +125°C. See Terminology section. Sample tested during initial release to ensure compliance. 4 Guaranteed no missed codes to 12 bits. 5 VIN− or VIN+ must remain within GND/VDD. 6 VIN− = 0 V for specified performance. For full input range on VIN− pin, see Figure 28 and Figure 29. 7 For full common-mode range, see Figure 24 and Figure 25. 8 Relates to Pin DCAPA or Pin DCAPB. 2 3 Rev. A | Page 4 of 28 875 ns with SCLK = 16 MHz Full-scale step input; VDD = 5 V Full-scale step input; VDD = 3 V AD7265 TIMING SPECIFICATIONS AVDD = DVDD = 2.7 V to 5.25 V, VDRIVE = 2.7 V to 5.25 V, internal/external reference = 2.5 V, TA = TMAX to TMIN, unless otherwise noted 1 . Table 2. Parameter fSCLK 2 tCONVERT tQUIET t2 t3 t4 3 t5 t6 t7 t8 t9 t10 Limit at TMIN , TMAX 1 4 16 14 × tSCLK 875 30 15/20 20/30 15 36 27 0.45 tSCLK 0.45 tSCLK 10 5 15 30 5 50 Unit MHz min MHz min MHz max ns max ns max ns min ns min ns min ns max ns max ns max ns min ns min ns min ns min ns max ns min ns min ns max Description TA = −40°C to +85°C TA > 85°C to 125°C tSCLK = 1/fSCLK fSCLK = 16 MHz Minimum time between end of serial read and next falling edge of CS VDD = 5 V/3 V, CS to SCLK setup time, TA = −40°C to +85°C VDD = 5 V/3 V, CS to SCLK setup time, TA > 85°C to 125°C Delay from CS until DOUTA and DOUTB are three-state disabled Data access time after SCLK falling edge, VDD = 3 V Data access time after SCLK falling edge, VDD = 5 V SCLK low pulse width SCLK high pulse width SCLK to data valid hold time, VDD = 3 V SCLK to data valid hold time, VDD = 5 V CS rising edge to DOUTA, DOUTB, high impedance CS rising edge to falling edge pulse width SCLK falling edge to DOUTA, DOUTB, high impedance SCLK falling edge to DOUTA, DOUTB, high impedance 1 Sample tested during initial release to ensure compliance. All input signals are specified with tr = tf = 5 ns (10% to 90% of VDD) and timed from a voltage level of 1.6 V. All timing specifications given are with a 25 pF load capacitance. With a load capacitance greater than this value, a digital buffer or latch must be used. See the Serial Interface section and Figure 41 and Figure 42. 2 Minimum SCLK for specified performance; with slower SCLK frequencies, performance specifications apply typically. 3 The time required for the output to cross 0.4 V or 2.4 V. Rev. A | Page 5 of 28 AD7265 ABSOLUTE MAXIMUM RATINGS Table 3. Parameter VDD to AGND DVDD to DGND VDRIVE to DGND VDRIVE to AGND AVDD to DVDD AGND to DGND Analog Input Voltage to AGND Digital Input Voltage to DGND Digital Output Voltage to GND VREF to AGND Input Current to Any Pin Except Supplies 1 Operating Temperature Range Storage Temperature Range Junction Temperature LFCSP/TQFP θJA Thermal Impedance θJC Thermal Impedance Lead Temperature, Soldering Reflow Temperature (10 sec to 30 sec) ESD 1 Rating −0.3 V to +7 V −0.3 V to +7 V −0.3 V to DVDD −0.3 V to AVDD −0.3 V to +0.3 V −0.3 V to +0.3 V −0.3 V to AVDD + 0.3 V −0.3 V to +7 V −0.3 V to VDRIVE + 0.3 V −0.3 V to AVDD + 0.3 V Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ESD CAUTION ±10 mA −40°C to +125°C −65°C to +150°C 150°C 108.2°C/W (LFCSP) 55°C/W (TQFP) 32.71°C/W (LFCSP) 255°C 1.5 kV Transient currents of up to 100 mA will not cause SCR latch up. Rev. A | Page 6 of 28 AD7265 DOUTB A0 CS SCLK AD7265 TOP VIEW (Not to Scale) 24 A1 23 A2 22 SGL/DIFF 21 RANGE 20 DCAP B AGND 6 19 AGND VA1 7 18 VB1 VA2 8 17 VB2 VB3 VB4 12 13 14 15 16 VB5 10 11 VB6 9 VA6 AGND 5 04674-041 AVDD 3 DCAP A 4 VA3 VA3 VA4 VA5 VA6 VB6 VB5 VB4 VB3 PIN 1 REF SELECT 2 VA5 TOP VIEW (Not to Scale) DGND 1 A1 A2 SGL/DIFF RANGE DCAPB AGND VB1 VB2 VA4 AD7265 24 23 22 21 20 19 18 17 DGND DVDD DOUTA DVDD VDRIVE DOUTA DGND DOUTB SCLK CS A0 32 31 30 29 28 27 26 25 PIN 1 INDICATOR 04674-002 1 2 3 4 5 6 7 8 32 31 30 29 28 27 26 25 9 10 11 12 13 14 15 16 DGND REF SELECT AVDD DCAPA AGND AGND VA1 VA2 VDRIVE PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS Figure 3. 32-Lead SU-32-2 Figure 2. 32-Lead CP-32-2 Table 4. Pin Function Descriptions Pin No. 1, 29 Mnemonic DGND 2 REF SELECT 3 AVDD 4, 20 DCAPA, DCAPB 5, 6, 19 AGND 7 to 12 VA1 to VA6 13 to 18 VB6 to VB1 21 RANGE 22 SGL/DIFF 23 to 25 A2 to A0 26 CS 27 SCLK Description Digital Ground. This is the ground reference point for all digital circuitry on the AD7265. Both DGND pins should connect to the DGND plane of a system. The DGND and AGND voltages should ideally be at the same potential and must not be more than 0.3 V apart, even on a transient basis. Internal/External Reference Selection. Logic input. If this pin is tied to DGND, the on-chip 2.5 V reference is used as the reference source for both ADC A and ADC B. In addition, Pin DCAPA and Pin DCAPB must be tied to decoupling capacitors. If the REF SELECT pin is tied to a logic high, an external reference can be supplied to the AD7265 through the DCAPA pin and/or the DCAPB pin. Analog Supply Voltage, 2.7 V to 5.25 V. This is the only supply voltage for all analog circuitry on the AD7265. The AVDD and DVDD voltages should ideally be at the same potential and must not be more than 0.3 V apart, even on a transient basis. This supply should be decoupled to AGND. Decoupling Capacitor Pins. Decoupling capacitors (470 nF recommended) are connected to these pins to decouple the reference buffer for each respective ADC. Provided the output is buffered, the on-chip reference can be taken from these pins and applied externally to the rest of a system. The range of the external reference is dependent on the analog input range selected. Analog Ground. Ground reference point for all analog circuitry on the AD7265. All analog input signals and any external reference signal should be referred to this AGND voltage. All three of these AGND pins should connect to the AGND plane of a system. The AGND and DGND voltages ideally should be at the same potential and must not be more than 0.3 V apart, even on a transient basis. Analog Inputs of ADC A. These may be programmed as six single-ended channels or three true differential analog input channel pairs. See Table 6. Analog Inputs of ADC B. These may be programmed as six single-ended channels or three true differential analog input channel pairs. See Table 6. Analog Input Range Selection. Logic input. The polarity on this pin determines the input range of the analog input channels. If this pin is tied to a logic low, the analog input range is 0 V to VREF. If this pin is tied to a logic high when CS goes low, the analog input range is 2 × VREF. See the Analog Input Selection section for details. Logic Input. This pin selects whether the analog inputs are configured as differential pairs or single ended. A logic low selects differential operation while a logic high selects single-ended operation. See the Analog Input Selection section for details. Multiplexer Select. Logic inputs. These inputs are used to select the pair of channels to be simultaneously converted, such as Channel 1 of both ADC A and ADC B, Channel 2 of both ADC A and ADC B, and so on. The pair of channels selected may be two single-ended channels or two differential pairs. The logic states of these pins need to be set up prior to the acquisition time and subsequent falling edge of CS to correctly set up the multiplexer for that conversion. See the Analog Input Selection section for further details and Table 6 for multiplexer address decoding. Chip Select. Active low logic input. This input provides the dual function of initiating conversions on the AD7265 and framing the serial data transfer. Serial Clock. Logic input. A serial clock input provides the SCLK for accessing the data from the AD7265. This clock is also used as the clock source for the conversion process. Rev. A | Page 7 of 28 AD7265 Pin No. 28, 30 Mnemonic DOUTB, DOUTA 31 VDRIVE 32 DVDD Description Serial Data Outputs. The data output is supplied to each pin as a serial data stream. The bits are clocked out on the falling edge of the SCLK input and 14 SCLKs are required to access the data. The data simultaneously appears on both pins from the simultaneous conversions of both ADCs. The data stream consists of two leading zeros followed by the 12 bits of conversion data. The data is provided MSB first. If CS is held low for 16 SCLK cycles rather than 14, then two trailing zeros appear after the 12 bits of data. If CS is held low for a further 16 SCLK cycles on either DOUTA or DOUTB, the data from the other ADC follows on the DOUT pin. This allows data from a simultaneous conversion on both ADCs to be gathered in serial format on either DOUTA or DOUTB using only one serial port. See the Serial Interface section. Logic Power Supply Input. The voltage supplied at this pin determines at what voltage the interface operates. This pin should be decoupled to DGND. The voltage at this pin may be different than that at AVDD and DVDD but should never exceed either by more than 0.3 V. Digital Supply Voltage, 2.7 V to 5.25 V. This is the supply voltage for all digital circuitry on the AD7265. The DVDD and AVDD voltages should ideally be at the same potential and must not be more than 0.3 V apart even on a transient basis. This supply should be decoupled to DGND. Rev. A | Page 8 of 28 AD7265 TYPICAL PERFORMANCE CHARACTERISTICS TA = 25°C, unless otherwise noted. –60 INTERNAL REFERENCE 4096 POINT FFT VDD = 5V, VDRIVE = 3V FSAMPLE = 1MSPS FIN = 26kHz SINAD = 71.4dB THD = –84.42dB DIFFERENTIAL MODE –10 –70 –30 –80 –50 (dB) –70 –100 0 200 –110 04674-003 –120 100mV p-p SINE WAVE ON AVDD NO DECOUPLING SINGLE-ENDED MODE 400 600 800 1000 1200 1400 1600 1800 2000 SUPPLY RIPPLE FREQUENCY (kHz) 0 50 100 150 0.8 –60 0.6 –65 0.4 DNL ERROR (LSB) –55 –75 –80 –85 –0.4 –0.8 100 200 300 400 500 600 700 NOISE FREQUENCY (kHz) 800 900 1000 VDD = 5V, VDRIVE = 3V DIFFERENTIAL MODE –0.2 –95 0 –1.0 0 500 1000 1500 1.0 RANGE = 0 TO VREF 3500 4000 0.6 VDD = 5V DIFFERENTIAL MODE 0.4 INL ERROR (LSB) SINAD (dB) 3000 VDD = 5V, VDRIVE = 3V DIFFERENTIAL MODE 0.8 72 2000 2500 CODE Figure 8. Typical DNL Figure 5. Channel-to-Channel Isolation 74 500 0 –0.6 –100 450 0.2 –90 04674-004 ISOLATION (dB) 1.0 VDD = 5V –70 400 Figure 7. FFT Figure 4. PSRR vs. Supply Ripple Frequency Without Supply Decoupling –50 200 250 300 350 FREQUENCY (kHz) 04674-006 –90 –110 04674-007 PSRR (dB) EXTERNAL REFERENCE –90 70 VDD = 3V DIFFERENTIAL MODE 0.2 0 –0.2 –0.4 68 –0.6 500 INPUT FREQUENCY (kHz) 1000 –1.0 04674-005 0 Figure 6. SINAD vs. Analog Input Frequency for Various Supply Voltages Rev. A | Page 9 of 28 0 500 1000 1500 2000 2500 CODE Figure 9. Typical INL 3000 3500 4000 04674-008 –0.8 66 AD7265 1.0 0.8 NO. OF OCCURRENCES POSITIVE INL 0 –0.2 NEGATIVE INL –0.4 –0.6 5000 4000 3000 1.0 1.5 2.0 2.5 0 2046 10000 INTERNAL REFERENCE 9000 11.0 NO. OF OCCURRENCES 10.0 VDD = 3V SINGLE-ENDED MODE 9.0 VDD = 3V DIFFERENTIAL MODE 2050 SINGLE-ENDED MODE 9984 CODES 8000 VDD = 5V SINGLE-ENDED MODE 8.5 2049 Figure 13. Histogram of Codes for 10k Samples in Differential Mode 11.5 9.5 2048 CODE 12.0 10.5 2047 04674-012 0.5 04674-009 0 Figure 10. Linearity Error vs. VREF VDD = 5V DIFFERENTIAL MODE 8.0 7000 6000 5000 4000 3000 2000 7.5 0.5 1.0 1.5 2.0 2.5 3.0 VREF (V) 3.5 4.0 4.5 5.0 04674-010 1000 0 0 2046 5 CODES 2047 11 CODES 2048 2049 04674-042 EFFECTIVE NUMBER OF BITS 6000 1000 VREF (V) 7.0 7000 2000 NEGATIVE DNL –0.8 –1.0 DIFFERENTIAL MODE 10000 CODES 8000 0.4 0.2 INTERNAL REFERENCE 9000 POSITIVE DNL 0.6 LINEARITY ERROR (LSB) 10000 VDD = 3V/5V DIFFERENTIAL MODE 2050 CODE Figure 11. Effective Number of Bits vs. VREF Figure 14. Histogram of Codes for 10k Samples in Single-Ended Mode 2.5010 –60 2.5005 –70 –75 CMRR (dB) 2.4995 2.4990 –80 –85 –90 2.4985 20 40 60 80 100 120 140 CURRENT LOAD (μA) 160 180 200 Figure 12. VREF vs. Reference Output Current Drive –100 0 200 400 600 800 RIPPLE FREQUENCY (kHz) 1000 Figure 15. CMRR vs. Common-Mode Ripple Frequency Rev. A | Page 10 of 28 1200 04674-040 –95 0 04674-011 VREF (V) 2.5000 2.4980 DIFFERENTIAL MODE VDD = 3V/5V –65 AD7265 TERMINOLOGY Differential Nonlinearity (DNL) Differential nonlinearity is the difference between the measured and the ideal 1 LSB change between any two adjacent codes in the ADC. Integral Nonlinearity (INL) Integral nonlinearity is the maximum deviation from a straight line passing through the endpoints of the ADC transfer function. The endpoints of the transfer function are zero scale with a single (1) LSB point below the first code transition, and full scale with a 1 LSB point above the last code transition. Offset Error Offset error applies to straight binary output coding. It is the deviation of the first code transition (00 . . . 000) to (00 . . . 001) from the ideal (AGND + 1 LSB). Signal-to-(Noise + Distortion) Ratio (SINAD) SINAD is the measured ratio of signal-to-(noise + distortion) at the output of the ADC. The signal is the rms amplitude of the fundamental. Noise is the sum of all non-fundamental signals up to half the sampling frequency (fS/2), excluding dc. The ratio is dependent on the number of quantization levels in the digitization process; the more levels, the smaller the quantization noise. The theoretical signal-to-(noise + distortion) ratio for an ideal N-bit converter with a sine wave input is given by Signal-to-(Noise + Distortion) = (6.02N + 1.76) dB Therefore, for a 12-bit converter, this is 74 dB. Total Harmonic Distortion (THD) Total harmonic distortion is the ratio of the rms sum of harmonics to the fundamental. For the AD7265, it is defined as Offset Error Match Offset error match is the difference in offset error across all 12 channels. THD ( dB ) = 20 log V 2 2 + V3 2 + V 4 2 + V5 2 + V6 2 V1 where: Gain Error Gain error applies to straight binary output coding. It is the deviation of the last code transition (111 . . . 110) to (111 . . . 111) from the ideal (VREF − 1 LSB) after the offset error is adjusted out. Gain error does not include reference error. V1 is the rms amplitude of the fundamental. V2, V3, V4, V5, and V6 are the rms amplitudes of the second through the sixth harmonics. Gain Error Match Gain error match is the difference in gain error across all 12 channels. Zero Code Error Zero code error applies when using twos complement output coding with, for example, the 2 × VREF input range as −VREF to +VREF biased about the VREF point. It is the deviation of the midscale transition (all 1s to all 0s) from the ideal VIN voltage (VREF). Zero Code Error Match Zero code error match refers to the difference in zero code error across all 12 channels. Positive Gain Error This applies when using twos complement output coding with, for example, the 2 × VREF input range as −VREF to +VREF biased about the VREF point. It is the deviation of the last code transition (011…110) to (011…111) from the ideal (+VREF − 1 LSB) after the zero code error is adjusted out. Track-and-Hold Acquisition Time The track-and-hold amplifier returns to track mode after the end of conversion. Track-and-hold acquisition time is the time required for the output of the track-and-hold amplifier to reach its final value, within ±1/2 LSB, after the end of conversion. Peak Harmonic or Spurious Noise Peak harmonic, or spurious noise, is defined as the ratio of the rms value of the next largest component in the ADC output spectrum (up to fS/2, excluding dc) to the rms value of the fundamental. Normally, the value of this specification is determined by the largest harmonic in the spectrum, but for ADCs where the harmonics are buried in the noise floor, it is a noise peak. Channel-to-Channel Isolation Channel-to-channel isolation is a measure of the level of crosstalk between channels. It is measured by applying a fullscale (2 × VREF when VDD = 5 V , and VREF when VDD = 3 V), 10 kHz sine wave signal to all unselected input channels and determining how much that signal is attenuated in the selected channel with a 50 kHz signal (0 V to VREF). The result obtained is the worst-case across all 12 channels for the AD7265. Intermodulation Distortion With inputs consisting of sine waves at two frequencies, fa and fb, any active device with nonlinearities creates distortion products at sum, and difference frequencies of mfa ± nfb where m, n = 0, 1, 2, 3, and so on. Intermodulation distortion terms are those for which neither m nor n are equal to zero. For example, the second-order terms include (fa + fb) and (fa − fb), while the third-order terms include (2fa + fb), (2fa − fb), (fa + 2fb), and (fa − 2fb). Rev. A | Page 11 of 28 AD7265 The AD7265 is tested using the CCIF standard where two input frequencies near the top end of the input bandwidth are used. In this case, the second-order terms are usually distanced in frequency from the original sine waves, while the third-order terms are usually at a frequency close to the input frequencies. As a result, the second-order and third-order terms are specified separately. The calculation of the intermodulation distortion is as per the THD specification, where it is the ratio of the rms sum of the individual distortion products to the rms amplitude of the sum of the fundamentals expressed in dBs. Common-Mode Rejection Ratio (CMRR) CMRR is defined as the ratio of the power in the ADC output at full-scale frequency, f, to the power of a 100 mV p-p sine wave applied to the common-mode voltage of VIN+ and VIN− of frequency fS as CMRR (dB) = 10 log(Pf/PfS) Thermal Hysteresis Thermal hysteresis is defined as the absolute maximum change of reference output voltage after the device is cycled through temperature from either T_HYS+ = +25°C to TMAX to +25°C or T_HYS− = +25°C to TMIN to +25°C It is expressed in ppm by VHYS ( ppm) = VREF (25°C) − VREF (T _ HYS) × 106 VREF (25°C) where: VREF (25°C) is VREF at 25°C. VREF (T_HYS) is the maximum change of VREF at T_HYS+ or T_HYS−. where: Pf is the power at frequency f in the ADC output. PfS is the power at frequency fS in the ADC output. Power Supply Rejection Ratio (PSRR) Variations in power supply affect the full-scale transition but not the converter’s linearity. PSRR is the maximum change in the full-scale transition point due to a change in power supply voltage from the nominal value (see Figure 4). Rev. A | Page 12 of 28 AD7265 THEORY OF OPERATION The AD7265 is a fast, micropower, dual, 12-bit, single-supply, ADC that operates from a 2.7 V to a 5.25 V supply. When operated from either a 3 V or a 5 V supply, the AD7265 is capable of throughput rates of 1 MSPS when provided with a 16 MHz clock. The AD7265 contains two on-chip, differential track-and-hold amplifiers, two successive approximation ADCs, and a serial interface with two separate data output pins. It is housed in a 32-lead LFCSP or a 32-lead TQFP, offering the user considerable space-saving advantages over alternative solutions. The serial clock input accesses data from the part, but also provides the clock source for each successive approximation ADC. The analog input range for the part can be selected to be a 0 V to VREF input or a 2 × VREF input, configured with either single-ended or differential analog inputs. The AD7265 has an on-chip 2.5 V reference that can be overdriven when an external reference is preferred. If the internal reference is to be used elsewhere in a system, then the output needs to be buffered first. The AD7265 also features power-down options to allow power saving between conversions. The power-down feature is implemented via the standard serial interface, as described in the Modes of Operation section. CONVERTER OPERATION The AD7265 has two successive approximation ADCs, each based around two capacitive DACs. Figure 16 and Figure 17 show simplified schematics of one of these ADCs in acquisition and conversion phase, respectively. The ADC is comprised of control logic, a SAR, and two capacitive DACs. In Figure 16 (the acquisition phase), SW3 is closed, SW1 and SW2 are in Position A, the comparator is held in a balanced condition, and the sampling capacitor arrays acquire the differential signal on the input. CS B A SW2 CS COMPARATOR CONTROL LOGIC SW3 B VREF CAPACITIVE DAC Figure 16. ADC Acquisition Phase 04674-013 VIN– A SW1 CAPACITIVE DAC CS B VIN+ VIN– A SW1 A SW2 CS COMPARATOR CONTROL LOGIC SW3 B VREF CAPACITIVE DAC Figure 17. ADC Conversion Phase ANALOG INPUT STRUCTURE Figure 18 shows the equivalent circuit of the analog input structure of the AD7265 in differential/pseudo differential modes. In single-ended mode, VIN− is internally tied to AGND. The four diodes provide ESD protection for the analog inputs. Care must be taken to ensure that the analog input signals never exceed the supply rails by more than 300 mV. This causes these diodes to become forward-biased and starts conducting into the substrate. These diodes can conduct up to 10 mA without causing irreversible damage to the part. The C1 capacitors in Figure 18 are typically 4 pF and can primarily be attributed to pin capacitance. The resistors are lumped components made up of the on resistance of the switches. The value of these resistors is typically about 100 Ω. The C2 capacitors are the ADC’s sampling capacitors with a capacitance of 45 pF typically. CAPACITIVE DAC VIN+ When the ADC starts a conversion (see Figure 17), SW3 opens and SW1 and SW2 move to Position B, causing the comparator to become unbalanced. Both inputs are disconnected once the conversion begins. The control logic and the charge redistribution DACs are used to add and subtract fixed amounts of charge from the sampling capacitor arrays to bring the comparator back into a balanced condition. When the comparator is rebalanced, the conversion is complete. The control logic generates the ADC output code. The output impedances of the sources driving the VIN+ and VIN− pins must be matched; otherwise, the two inputs will have different settling times, resulting in errors. 04674-014 CIRCUIT INFORMATION For ac applications, removing high frequency components from the analog input signal is recommended by the use of an RC low-pass filter on the relevant analog input pins with optimum values of 47 Ω and 10 pF. In applications where harmonic distortion and signal-to-noise ratio are critical, the analog input should be driven from a low impedance source. Large source impedances significantly affect the ac performance of the ADC and may necessitate the use of an input buffer amplifier. The choice of the op amp is a function of the particular application. Rev. A | Page 13 of 28 AD7265 VDD C1 R1 C2 –50 D FSAMPLE = 1MSPS VDD = 3V/5V –55 RANGE = 0 TO VREF VDD VIN– C1 –60 R1 C2 04674-015 D Figure 18. Equivalent Analog Input Circuit, Conversion Phase—Switches Open, Track Phase—Switches Closed –50 RSOURCE = 300Ω THD (dB) –70 RSOURCE = 100Ω RSOURCE = 0Ω RSOURCE = 47Ω –80 RSOURCE = 10Ω 0 100 200 300 400 INPUT FREQUENCY (kHz) 500 600 04674-016 –90 –85 –90 VDD = 5V SINGLE-ENDED MODE 0 100 200 300 400 INPUT FREQUENCY (kHz) 600 ANALOG INPUTS The AD7265 has a total of 12 analog inputs. Each on-board ADC has six analog inputs that can be configured as six singleended channels, three pseudo differential channels, or three fully differential channels. These can be selected as described in the Analog Input Selection section. If the analog input signal to be sampled is bipolar, the internal reference of the ADC can be used to externally bias up this signal to make it correctly formatted for the ADC. Figure 22 shows a typical connection diagram when operating the ADC in single-ended mode. +2.5V R +1.25V FSAMPLE = 1MSPS VDD = 3V RANGE = 0V TO VREF –65 500 Figure 21. THD vs. Analog Input Frequency for Various Supply Voltages Figure 19. THD vs. Analog Input Frequency for Various Source Impedances, Single-Ended Mode –60 VDD = 5V DIFFERENTIAL MODE The AD7265 can have a total of 12 single-ended analog input channels. In applications where the signal source has high impedance, it is recommended to buffer the analog input before applying it to the ADC. The analog input range can be programmed to be either 0 to VREF or 0 to 2 × VREF. –65 –85 –75 Single-Ended Mode –60 –75 VDD = 3V DIFFERENTIAL MODE –70 –80 When no amplifier is used to drive the analog input, the source impedance should be limited to low values. The maximum source impedance depends on the amount of THD that can be tolerated. The THD increases as the source impedance increases and performance degrades. Figure 19 shows a graph of the THD vs. the analog input signal frequency for different source impedances in single-ended mode, while Figure 20 shows the THD vs. the analog input signal frequency for different source impedances in differential mode. FSAMPLE = 1MSPS VDD = 3V –55 RANGE = 0V TO VREF VDD = 3V SINGLE-ENDED MODE –65 THD (dB) D 04674-018 D VIN+ Figure 21 shows a graph of the THD vs. the analog input frequency for various supplies while sampling at 1 MSPS. In this case, the source impedance is 47 Ω. 0V RSOURCE = 300Ω –1.25V VIN 0V R VA1 3R AD72651 R RSOURCE = 0Ω VB6 DCAP A/DCAP B RSOURCE = 100Ω –80 RSOURCE = 47Ω 1ADDITIONAL –85 RSOURCE = 10Ω –90 PINS OMITTED FOR CLARITY. Figure 22. Single-Ended Mode Connection Diagram 0 100 200 300 400 INPUT FREQUENCY (kHz) 500 600 Figure 20. THD vs. Analog Input Frequency for Various Source Impedances, Differential Mode Rev. A | Page 14 of 28 04674-019 0.47µF –75 04674-017 THD (dB) –70 AD7265 3.5 The AD7265 can have a total of six differential analog input pairs. 3.0 COMMON-MODE RANGE (V) Differential Mode Differential signals have some benefits over single-ended signals, including noise immunity based on the device’s common-mode rejection and improvements in distortion performance. Figure 23 defines the fully differential analog input of the AD7265. VREF p-p VIN+ TA = 25°C 2.5 2.0 1.5 1.0 0.5 PINS OMITTED FOR CLARITY. 0 0.5 1.0 1.5 2.0 2.5 3.0 VREF (V) 3.5 4.0 4.5 5.0 Figure 24. Input Common-Mode Range vs. VREF (0 to VREF Range, VDD = 5 V) 5.0 Figure 23. Differential Input Definition TA = 25°C 4.5 4.0 COMMON-MODE RANGE (V) The amplitude of the differential signal is the difference between the signals applied to the VIN+ and VIN− pins in each differential pair (VIN+ − VIN−). VIN+ and VIN− should be simultaneously driven by two signals each of amplitude VREF (or 2 × VREF, depending on the range chosen) that are 180° out of phase. The amplitude of the differential signal is therefore (assuming the 0 to VREF range is selected) −VREF to +VREF peakto-peak (2 × VREF), regardless of the common mode (CM). The common mode is the average of the two signals 3.5 3.0 2.5 2.0 1.5 1.0 0.5 (VIN+ + VIN−)/2 0 0 0.5 1.0 1.5 VREF (V) and is therefore the voltage on which the two inputs are centered. 2.0 2.5 04674-022 1ADDITIONAL 0 VIN– 04674-020 VREF p-p 04674-021 AD72651 COMMON MODE VOLTAGE Figure 25. Input Common-Mode Range vs. VREF (2 × VREF Range, VDD = 5 V) This results in the span of each input being CM ± VREF/2. This voltage has to be set up externally, and its range varies with the reference value, VREF. As the value of VREF increases, the commonmode range decreases. When driving the inputs with an amplifier, the actual common-mode range is determined by the amplifier’s output voltage swing. Figure 24 and Figure 25 show how the common-mode range typically varies with VREF for a 5 V power supply using the 0 to VREF range or 2 × VREF range, respectively. The common mode must be in this range to guarantee the functionality of the AD7265. When a conversion takes place, the common mode is rejected, resulting in a virtually noise-free signal of amplitude −VREF to +VREF corresponding to the digital codes of 0 to 4096. If the 2 × VREF range is used, then the input signal amplitude extends from −2 VREF to +2 VREF after conversion. Driving Differential Inputs Differential operation requires that VIN+ and VIN− be simultaneously driven with two equal signals that are 180° out of phase. The common mode must be set up externally. The common-mode range is determined by VREF, the power supply, and the particular amplifier used to drive the analog inputs. Differential modes of operation with either an ac or dc input provide the best THD performance over a wide frequency range. Because not all applications have a signal preconditioned for differential operation, there is often a need to perform single-ended-to-differential conversion. Rev. A | Page 15 of 28 AD7265 Using an Op Amp Pair Pseudo Differential Mode An op amp pair can be used to directly couple a differential signal to one of the analog input pairs of the AD7265. The circuit configurations illustrated in Figure 26 and Figure 27 show how a dual op amp can be used to convert a single-ended signal into a differential signal for both a bipolar and unipolar input signal, respectively. The AD7265 can have a total of six pseudo differential pairs. In this mode, VIN+ is connected to the signal source that must have an amplitude of VREF (or 2 × VREF, depending on the range chosen) to make use of the full dynamic range of the part. A dc input is applied to the VIN− pin. The voltage applied to this input provides an offset from ground or a pseudo ground for the VIN+ input. The benefit of pseudo differential inputs is that they separate the analog input signal ground from the ADC’s ground allowing dc common-mode voltages to be cancelled. The typical voltage range for the VIN− pin, while in pseudo differential mode, is shown in Figure 28 and Figure 29. Figure 30 shows a connection diagram for pseudo differential mode. The voltage applied to Point A sets up the common-mode voltage. In both diagrams, it is connected in some way to the reference, but any value in the common-mode range can be input here to set up the common mode. The AD8022 is a suitable dual op amp that can be used in this configuration to provide differential drive to the AD7265. 1.0 Take care when choosing the op amp; the selection depends on the required power supply and system performance objectives. The driver circuits in Figure 26 and Figure 27 are optimized for dc coupling applications requiring best distortion performance. 0.8 0.6 0.4 VIN– (V) The differential op amp driver circuit shown in Figure 27 is configured to convert and level shift a single-ended, groundreferenced (bipolar) signal to a differential signal centered at the VREF level of the ADC. 27Ω –0.2 –0.4 3.75V 2.5V 1.25V VIN+ GND 0 0.5 AD72651 V+ 27Ω A 2.5 3.75V 2.5V 1.25V VIN– (V) 04674-023 PINS OMITTED FOR CLARITY. Figure 26. Dual Op Amp Circuit to Convert a Single-Ended Unipolar Signal into a Differential Signal GND 440Ω 3.75V V+ 27Ω TA = 25°C 1.0 0.5 0 –0.5 2.5V 1.25V VIN+ 0 1 AD7265 220Ω 220Ω 3.75V V+ 27Ω A 0.5 1.0 1.5 2.0 2.5 3.0 VREF (V) VREF p–p 2.5V 1.25V 4.0 4.5 5.0 AD72651 VIN+ VIN– DCAP A/DCAP B V– 10kΩ 0.47µF PINS OMITTED FOR CLARITY. 04674-024 20kΩ 1ADDITIONAL 3.5 Figure 29. VIN− Input Voltage Range vs. VREF in Pseudo Differential Mode with VDD = 5 V V– 220kΩ 3.0 1.5 0.47µF 220Ω 2.5 2.0 10kΩ 2 × VREF p-p 2.0 VIN– DCAP A/DCAP B V– 1ADDITIONAL 1.5 VREF (V) Figure 28. VIN− Input Voltage Range vs. VREF in Pseudo Differential Mode with VDD = 3 V V– 220Ω 220Ω 1.0 Figure 27. Dual Op Amp Circuit to Convert a Single-Ended Bipolar Signal into a Differential Unipolar Signal Rev. A | Page 16 of 28 DC INPUT VOLTAGE VIN– VREF 0.47µF 1ADDITIONAL PINS OMITTED FOR CLARITY. Figure 30. Pseudo Differential Mode Connection Diagram 04674-044 V+ 0 04674-025 VREF 440Ω 220Ω 0.2 04674-043 The circuit configuration shown in Figure 26 converts a unipolar, single-ended signal into a differential signal. 2 × VREF p-p TA = 25°C AD7265 ANALOG INPUT SELECTION The analog inputs of the AD7265 can be configured as singleended or true differential via the SGL/DIFF logic pin, as shown in Figure 31. If this pin is tied to a logic low, the analog input channels to each on-chip ADC are set up as three true differential pairs. If this pin is at logic high, the analog input channels to each on-chip ADC are set up as six single-ended analog inputs. The required logic level on this pin needs to be established prior to the acquisition time and remain unchanged during the conversion time until the track-and-hold has returned to track. The track-and-hold returns to track on the 13th rising edge of SCLK after the CS falling edge (see Figure 41). If the level on this pin is changed, it is recognized by the AD7265; therefore, it is necessary to keep the same logic level during acquisition and conversion to avoid corrupting the conversion in progress. For example, in Figure 31, the SGL/DIFF pin is set at logic high for the duration of both the acquisition and conversion times so the analog inputs are configured as single ended for that conversion (Sampling Point A). The logic level of the SGL/DIFF changed to low after the track-and-hold returned to track and prior to the required acquisition time for the next sampling instant at Point B; therefore, the analog inputs are configured as differential for that conversion. tACQ 1 14 The analog input range of the AD7265 can be selected as 0 V to VREF or 0 V to 2 × VREF via the RANGE pin. This selection is made in a similar fashion to that of the SGL/DIFF pin by setting the logic state of the RANGE pin a time tacq prior to the falling edge of CS. Subsequent to this, the logic level on this pin can be altered after the third falling edge of SCLK. If this pin is tied to a logic low, the analog input range selected is 0 V to VREF. If this pin is tied to a logic high, the analog input range selected is 0 V to 2 × VREF. OUTPUT CODING The AD7265 output coding is set to either twos complement or straight binary, depending on which analog input configuration is selected for a conversion. Table 5 shows which output coding scheme is used for each possible analog input configuration. Table 5. AD7265 Output Coding B A CS The channels used for simultaneous conversions are selected via the multiplexer address input pins, A0 to A2. The logic states of these pins also need to be established prior to the acquisition time; however, they may change during the conversion time, provided that the mode is not changed. If the mode is changed from fully differential to pseudo-differential, for example, then the acquisition time would start again from this point. The selected input channels are decoded as shown in Table 6. 1 14 04674-026 SCLK SGL/DIFF Figure 31. Selecting Differential or Single-Ended Configuration SGL/DIFF DIFF DIFF SGL SGL PSEUDO DIFF PSEUDO DIFF Range Output Coding 0 V to VREF 0 V to 2 × VREF 0 V to VREF 0 V to 2 × VREF 0 V to VREF 0 V to 2 × VREF Twos complement Twos complement Straight binary Twos complement Straight binary Twos complement Table 6. Analog Input Type and Channel Selection SGL/DIFF 1 1 1 1 1 1 0 0 0 0 0 0 A2 0 0 0 0 1 1 0 0 0 0 1 1 A1 0 0 1 1 0 0 0 0 1 1 0 0 A0 0 1 0 1 0 1 0 1 0 1 0 1 VIN+ VA1 VA2 VA3 VA4 VA5 VA6 VA1 VA1 VA3 VA3 VA5 VA5 ADC A VIN− AGND AGND AGND AGND AGND AGND VA2 VA2 VA4 VA4 VA6 VA6 VIN+ VB1 VB2 VB3 VB4 VB5 VB6 VB1 VB1 VB3 VB3 VB5 VB5 Rev. A | Page 17 of 28 ADC B VIN− AGND AGND AGND AGND AGND AGND VB2 VB2 VB4 VB4 VB6 VB6 Comment Single ended Single ended Single ended Single ended Single ended Single ended Fully differential Pseudo differential Fully differential Pseudo differential Fully differential Pseudo differential AD7265 TRANSFER FUNCTIONS DIGITAL INPUTS The designed code transitions occur at successive integer LSB values (1 LSB, 2 LSB, and so on). In single-ended mode, the LSB size is VREF/4096 when the 0 V to VREF range is used, and the LSB size is 2 × VREF/4096 when the 0 V to 2 × VREF range is used. In differential mode, the LSB size is 2 × VREF/4096 when the 0 V to VREF range is used, and the LSB size is 4 × VREF/4096 when the 0 V to 2 × VREF range is used. The ideal transfer characteristic for the AD7265 when straight binary coding is output is shown in Figure 32, and the ideal transfer characteristic for the AD7265 when twos complement coding is output is shown (with the 2 × VREF range) in Figure 33. The digital inputs applied to the AD7265 are not limited by the maximum ratings that limit the analog inputs. Instead, the digital inputs can be applied up to 7 V and are not restricted by the VDD + 0.3 V limit, as are the analog inputs. See the Absolute Maximum Ratings section for more information. Another advantage of the SCLK, RANGE, A0 to A2, and CS pins not being restricted by the VDD + 0.3 V limit is that power supply sequencing issues are avoided. If one of these digital inputs is applied before VDD, there is no risk of latch-up, as there would be on the analog inputs if a signal greater than 0.3 V were applied prior to VDD. VDRIVE The AD7265 also has a VDRIVE feature to control the voltage at which the serial interface operates. VDRIVE allows the ADC to easily interface to both 3 V and 5 V processors. For example, if the AD7265 was operated with a VDD of 5 V, the VDRIVE pin could be powered from a 3 V supply, allowing a large dynamic range with low voltage digital processors. Therefore, the AD7265 could be used with the 2 × VREF input range, with a VDD of 5 V while still being able to interface to 3 V digital parts. 111...111 ADC CODE 111...110 111...000 1LSB = VREF/4096 011...111 000...010 000...001 000...000 VREF – 1LSB 0V 1LSB 04674-027 ANALOG INPUT NOTE 1. VREF IS EITHER VREF OR 2 × VREF. Figure 32. Straight Binary Transfer Characteristic 1LSB = 2 × VREF/4096 011...111 000...001 000...000 111...111 100...010 100...001 100...000 –VREF + 1LSB VREF – 1LSB +VREF – 1 LSB ANALOG INPUT 04674-028 ADC CODE 011...110 Figure 33. Twos Complement Transfer Characteristic with VREF ± VREF Input Range Rev. A | Page 18 of 28 AD7265 MODES OF OPERATION NORMAL MODE This mode is intended for applications that need the fastest throughput rates because the user does not have to worry about any power-up times with the AD7265 remaining fully powered at all times. Figure 34 shows the general diagram of the operation of the AD7265 in this mode. CS 1 10 14 DOUTA DOUTB LEADING ZEROS + CONVERSION RESULT 04674-029 SCLK Figure 34. Normal Mode Operation The conversion is initiated on the falling edge of CS, as described in the Serial Interface section. To ensure that the part remains fully powered up at all times, CS must remain low until at least 10 SCLK falling edges have elapsed after the falling edge of CS. If CS is brought high any time after the 10th SCLK falling edge but before the 14th SCLK falling edge, the part remains powered up, but the conversion is terminated and DOUTA and DOUTB go back into three-state. Fourteen serial clock cycles are required to complete the conversion and access the conversion result. The DOUT line does not return to three-state after 14 SCLK cycles have elapsed, but instead does so when CS is brought high again. If CS is left low for another 2 SCLK cycles (for example, if only a 16 SCLK burst is available), two trailing zeros are clocked out after the data. If CS is left low for a further 14 (or 16) SCLK cycles, the result from the other ADC on board is also accessed on the same DOUT line, as shown in Figure 42 (see the Serial Interface section). Once 32 SCLK cycles have elapsed, the DOUT line returns to three-state on the 32nd SCLK falling edge. If CS is brought high prior to this, the DOUT line returns to three-state at that point. Therefore, CS may idle low after 32 SCLK cycles until it is brought high again sometime prior to the next conversion (effectively idling CS low), if so desired, because the bus still returns to three-state upon completion of the dual result read. Once a data transfer is complete and DOUTA and DOUTB have returned to three-state, another conversion can be initiated after the quiet time, tQUIET, has elapsed by bringing CS low again (assuming the required acquisition time is allowed). PARTIAL POWER-DOWN MODE This mode is intended for use in applications where slower throughput rates are required. Either the ADC is powered down between each conversion, or a series of conversions may be performed at a high throughput rate, and the ADC is then powered down for a relatively long duration between these bursts of several conversions. When the AD7265 is in partial power-down, all analog circuitry is powered down except for the on-chip reference and reference buffer. To enter partial power-down mode, the conversion process must be interrupted by bringing CS high anywhere after the second falling edge of SCLK and before the 10th falling edge of SCLK, as shown in Figure 35. Once CS is brought high in this window of SCLKs, the part enters partial power-down, the conversion that was initiated by the falling edge of CS is terminated, and DOUTA and DOUTB go back into three-state. If CS is brought high before the second SCLK falling edge, the part remains in normal mode and does not power down. This avoids accidental power-down due to glitches on the CS line. CS 1 2 10 14 SCLK DOUTA DOUTB Rev. A | Page 19 of 28 THREE-STATE Figure 35. Entering Partial Power-Down Mode 04674-030 The mode of operation of the AD7265 is selected by controlling the (logic) state of the CS signal during a conversion. There are three possible modes of operation: normal mode, partial powerdown mode, and full power-down mode. After a conversion is initiated, the point at which CS is pulled high determines which power-down mode, if any, the device enters. Similarly, if already in a power-down mode, CS can control whether the device returns to normal operation or remains in power-down. These modes of operation are designed to provide flexible power management options. These options can be chosen to optimize the power dissipation/throughput rate ratio for differing application requirements. AD7265 When the AD7265 is in full power-down, all analog circuitry is powered down. Full power-down is entered in a similar way as partial power-down, except the timing sequence shown in Figure 35 must be executed twice. The conversion process must be interrupted in a similar fashion by bringing CS high anywhere after the second falling edge of SCLK and before the 10th falling edge of SCLK. The device enters partial power-down at this point. To reach full power-down, the next conversion cycle must be interrupted in the same way, as shown in Figure 37. Once CS is brought high in this window of SCLKs, the part completely powers down. To exit this mode of operation and power up the AD7265 again, a dummy conversion is performed. On the falling edge of CS, the device begins to power up and continues to power up as long as CS is held low until after the falling edge of the 10th SCLK. The device is fully powered up after approximately 1 μs has elapsed, and valid data results from the next conversion, as shown in Figure 36. If CS is brought high before the second falling edge of SCLK, the AD7265 again goes into partial power-down. This avoids accidental power-up due to glitches on the CS line. Although the device may begin to power up on the falling edge of CS, it powers down again on the rising edge of CS. If the AD7265 is already in partial power-down mode and CS is brought high between the second and 10th falling edges of SCLK, the device enters full power-down mode. Note that it is not necessary to complete the 14 SCLKs once CS is brought high to enter a power-down mode. To exit full power-down and power up the AD7265, a dummy conversion is performed, as when powering up from partial power-down. On the falling edge of CS, the device begins to power up and continues to power up, as long as CS is held low until after the falling edge of the 10th SCLK. The required power-up time must elapse before a conversion can be initiated, as shown in Figure 38. See the Power-Up Times section for the power-up times associated with the AD7265. FULL POWER-DOWN MODE This mode is intended for use in applications where throughput rates slower than those in the partial power-down mode are required, as power-up from a full power-down takes substantially longer than that from partial power-down. This mode is more suited to applications where a series of conversions performed at a relatively high throughput rate are followed by a long period of inactivity and thus power-down. THE PART IS FULLY POWERED UP; SEE POWER-UP TIMES SECTION. THE PART BEGINS TO POWER UP. tPOWER-UP1 CS 1 10 DOUTA DOUTB 14 1 INVALID DATA 14 04674-031 SCLK VALID DATA Figure 36. Exiting Partial Power-Down Mode THE PART ENTERS PARTIAL POWER DOWN. THE PART BEGINS TO POWER UP. THE PART ENTERS FULL POWER DOWN. CS DOUTA DOUTB 1 2 10 INVALID DATA 14 THREE-STATE 1 2 10 INVALID DATA Figure 37. Entering Full Power-Down Mode Rev. A | Page 20 of 28 14 THREE-STATE 04674-032 SCLK AD7265 THE PART BEGINS TO POWER UP. THE PART IS FULLY POWERED UP, SEE POWER-UP TIMES SECTION. tPOWER-UP2 CS DOUTA DOUTB 14 10 1 14 1 INVALID DATA 04674-033 SCLK VALID DATA Figure 38. Exiting Full Power-Down Mode Once supplies are applied to the AD7265, enough time must be allowed for any external reference to power up and charge the various reference buffer decoupling capacitors to their final values. TA = 25°C 9.5 9.0 8.5 8.0 7.5 7.0 VARIABLE SCLK 6.5 16MHz SCLK 6.0 5.5 5.0 0 100 200 300 400 500 600 700 THROUGHPUT (kSPS) 800 900 1000 04674-045 When power supplies are first applied to the AD7265, the ADC may power up in either of the power-down modes or normal mode. Because of this, it is best to allow a dummy cycle to elapse to ensure the part is fully powered up before attempting a valid conversion. Likewise, if it is intended to keep the part in the partial power-down mode immediately after the supplies are applied, then two dummy cycles must be initiated. The first dummy cycle must hold CS low until after the 10th SCLK falling edge (see Figure 34); in the second cycle, CS must be brought high before the 10th SCLK edge but after the second SCLK falling edge (see Figure 35). Alternatively, if it is intended to place the part in full power-down mode when the supplies are applied, then three dummy cycles must be initiated. The first dummy cycle must hold CS low until after the 10th SCLK falling edge (see Figure 34); the second and third dummy cycles place the part in full power-down (see Figure 37). 10.0 Figure 39. Power vs. Throughput in Normal Mode with VDD = 3 V 25 TA = 25°C 23 21 19 15 16MHz SCLK 13 11 9 POWER vs. THROUGHPUT RATE 7 The power consumption of the AD7265 varies with throughput rate. When using very slow throughput rates and as fast an SCLK frequency as possible, the various power-down options 5 Rev. A | Page 21 of 28 VARIABLE SCLK 17 0 100 200 300 400 500 600 700 THROUGHPUT (kSPS) 800 900 1000 Figure 40. Power vs. Throughput in Normal Mode with VDD = 5 V 04674-046 To power up from full power-down (whether using an internal or external reference), approximately 1.5 ms should be allowed from the falling edge of CS, shown as tPOWER-UP2 in Figure 38. Powering up from partial power-down requires much less time. The power-up time from partial power-down is typically 1 μs; however, if using the internal reference, then the AD7265 must be in partial power-down for at least 67 μs in order for this power-up time to apply. POWER (mW) As described in detail, the AD7265 has two power-down modes, partial power-down and full power-down. This section deals with the power-up time required when coming out of either of these modes. It should be noted that the power-up times, as explained in this section, apply with the recommended capacitors in place on the DCAPA and DCAPB pins. can be used to make significant power savings. However, the AD7265 quiescent current is low enough that even without using the power-down options, there is a noticeable variation in power consumption with sampling rate. This is true whether a fixed SCLK value is used or if it is scaled with the sampling rate. Figure 39 and Figure 40 show plots of power vs. the throughput rate when operating in normal mode for a fixed maximum SCLK frequency, and an SCLK frequency that scales with the sampling rate with VDD = 3 V and VDD = 5 V, respectively. In all cases, the internal reference was used. POWER (mW) POWER-UP TIMES AD7265 SERIAL INTERFACE A minimum of 14 serial clock cycles are required to perform the conversion process and to access data from one conversion on either data line of the AD7265. CS going low provides the leading zero to be read in by the microcontroller or DSP. The remaining data is then clocked out by subsequent SCLK falling edges, beginning with a second leading zero. Therefore, the first falling clock edge on the serial clock has the leading zero provided and also clocks out the second leading zero. The 12-bit result then follows with the final bit in the data transfer valid on the 14th falling edge, having being clocked out on the previous (13th) falling edge. It may also be possible to read in data on each SCLK rising edge depending on the SCLK frequency or the supply voltage. The first rising edge of SCLK after the CS falling edge would have the second leading zero provided, and the 13th rising SCLK edge would have DB0 provided. Figure 41 shows the detailed timing diagram for serial interfacing to the AD7265. The serial clock provides the conversion clock and controls the transfer of information from the AD7265 during conversion. The CS signal initiates the data transfer and conversion process. The falling edge of CS puts the track-and-hold into hold mode, at which point the analog input is sampled and the bus is taken out of three-state. The conversion is also initiated at this point and requires a minimum of 14 SCLKs to complete. Once 13 SCLK falling edges have elapsed, the track-and-hold goes back into track on the next SCLK rising edge, as shown in Figure 41 at Point B. If a 16-SCLK transfer is used, then two trailing zeros will appear after the final LSB. On the rising edge of CS, the conversion is terminated and DOUTA and DOUTB go back into three-state. If CS is not brought high but is instead held low for a further 14 (or 16) SCLK cycles on DOUTA, the data from Conversion B is output on DOUTA (followed by 2 trailing zeros). Note that with fast SCLK values, and thus short SCLK periods, in order to allow adequately for t2, an SCLK rising edge may occur before the first SCLK falling edge. This rising edge of SCLK can be ignored for the purposes of the timing descriptions in this section. If a falling edge of SCLK is coincident with the falling edge of CS, then this falling edge of SCLK is not acknowledged by the AD7265, and the next falling edge of SCLK will be the first registered after the falling edge of CS. Likewise, if CS is held low for a further 14 (or 16) SCLK cycles on DOUTB, the data from Conversion A is output on DOUTB. This is illustrated in Figure 42 where the case for DOUTA is shown. In this case, the DOUT line in use goes back into three-state on the 32nd SCLK falling edge or the rising edge of CS, whichever occurs first. CS t9 SCLK t6 1 3 2 4 t3 DOUTA DB11 0 0 DOUTB THREESTATE 2 LEADING ZEROS B 5 t4 DB10 13 t5 t7 DB9 DB2 DB8 tQUIET t8 DB1 DB0 THREE-STATE 04674-034 t2 Figure 41. Serial Interface Timing Diagram CS t6 2 1 3 4 t3 DOUTA 0 ZERO DB11A THREESTATE 2 LEADING ZEROS 5 t4 DB10A DB9A t5 14 16 15 32 17 t10 t7 ZERO ZERO ZERO ZERO DB11B 2 TRAILING ZEROS 2 LEADING ZEROS Figure 42. Reading Data from Both ADCs on One DOUT Line with 32 SCLKs Rev. A | Page 22 of 28 ZERO ZERO 2 TRAILING ZEROS THREESTATE 04674-035 t2 SCLK AD7265 MICROPROCESSOR INTERFACING The serial interface on the AD7265 allows the part to be directly connected to a range of many different microprocessors. This section explains how to interface the AD7265 with some of the more common microcontroller and DSP serial interface protocols. AD7265 TO ADSP-218x The ADSP-218x family of DSPs interface directly to the AD7265 without any glue logic required. The VDRIVE pin of the AD7265 takes the same supply voltage as that of the ADSP-218x. This allows the ADC to operate at a higher supply voltage than its serial interface and, therefore, the ADSP-218x, if necessary. This example shows both DOUTA and DOUTB of the AD7265 connected to both serial ports of the ADSP-218x. The SPORT0 and SPORT1 control registers should be set up as shown in Table 7 and Table 8. The connection diagram is shown in Figure 43. The ADSP-218x has the TFS0 and RFS0 of the SPORT0 and the RFS1 of SPORT1 tied together. TFS0 is set as an output, and both RFS0 and RFS1 are set as inputs. The DSP operates in alternate framing mode, and the SPORT control register is set up as described. The frame synchronization signal generated on the TFS is tied to CS, and, as with all signal processing applications, equidistant sampling is necessary. However, in this example, the timer interrupt is used to control the sampling rate of the ADC and, under certain conditions, equidistant sampling may not be achieved. AD72651 ADSP-218x1 SCLK SCLK0 SCLK1 CS TFS0 RFS0 Table 7. SPORT0 Control Register Setup ISCLK = 1 TFSR = RFSR = 1 IRFS = 0 ITFS = 1 Description Alternate framing Active low frame signal Right justify data 16-bit data-word (or may be set to 1101 for 14-bit data-word) Internal serial clock Frame every word ISCLK = 0 TFSR = RFSR = 1 IRFS = 0 ITFS = 1 DR0 DOUTB DR1 VDRIVE VDD 1ADDITIONAL PINS OMITTED FOR CLARITY. Figure 43. Interfacing the AD7265 to the ADSP-218x The timer registers are loaded with a value that provides an interrupt at the required sample interval. When an interrupt is received, a value is transmitted with TFS/DT (ADC control word). The TFS is used to control the RFS, and hence, the reading of data. The frequency of the serial clock is set in the SCLKDIV register. When the instruction to transmit with TFS is given (AX0 = TX0), the state of the SCLK is checked. The DSP waits until the SCLK has gone high, low, and high again before transmission starts. If the timer and SCLK values are chosen such that the instruction to transmit occurs on or near the rising edge of SCLK, then the data may be transmitted or it may wait until the next clock edge. Table 8. SPORT1 Control Register Setup Setting TFSW = RFSW = 1 INVRFS = INVTFS = 1 DTYPE = 00 SLEN = 1111 DOUTA 04674-036 Setting TFSW = RFSW = 1 INVRFS = INVTFS = 1 DTYPE = 00 SLEN = 1111 RFS1 Description Alternate framing Active low frame signal Right justify data 16-bit data-word (or may be set to 1101 for 14-bit data-word) External serial clock Frame every word To implement the power-down modes, SLEN should be set to 1001 to issue an 8-bit SCLK burst. For example, the ADSP-2111 has a master clock frequency of 16 MHz. If the SCLKDIV register is loaded with the value 3, then an SCLK of 2 MHz is obtained, and eight master clock periods will elapse for every one SCLK period. If the timer registers are loaded with the value 803, then 100.5 SCLKs will occur between interrupts and, subsequently, between transmit instructions. This situation yields sampling that is not equidistant, as the transmit instruction is occurring on a SCLK edge. If the number of SCLKs between interrupts is a whole integer figure of N, then equidistant sampling will be implemented by the DSP. Rev. A | Page 23 of 28 AD7265 AD7265 to ADSP-BF53x AD7265 TO TMS320C541 The ADSP-BF53x family of DSPs interface directly to the AD7265 without any glue logic required. The availability of secondary receive registers on the serial ports of the Blackfin® DSPs means only one serial port is necessary to read from both DOUT pins simultaneously. Figure 44 shows both DOUTA and DOUTB of the AD7265 connected to Serial Port 0 of the ADSP-BF53x. The SPORT0 Receive Configuration 1 register and SPORT0 Receive Configuration 2 register should be set up as outlined in Table 9 and Table 10. The serial interface on the TMS320C541 uses a continuous serial clock and frame synchronization signals to synchronize the data transfer operations with peripheral devices like the AD7265. The CS input allows easy interfacing between the TMS320C541 and the AD7265 without any glue logic required. The serial ports of the TMS320C541 are set up to operate in burst mode with internal CLKX0 (TX serial clock on Serial Port 0) and FSX0 (TX frame sync from Serial Port 0). The serial port control registers (SPC) must have the following setup. CS VDRIVE SPC SPC0 SPC1 DR0PRI DR0SEC Figure 44. Interfacing the AD7265 to the ADSP-BF53x Table 9. The SPORT0 Receive Configuration 1 Register (SPORT0_RCR1) SLEN = 1111 TFSR = RFSR = 1 FSM 1 1 MCM 1 0 TXM 1 0 The format bit, FO, may be set to 1 to set the word length to 8 bits to implement the power-down modes on the AD7265. SERIAL DEVICE B (SECONDARY) PINS OMITTED FOR CLARITY. Setting RCKFE = 1 LRFS = 1 RFSR = 1 IRFS = 1 RLSBIT = 0 RDTYPE = 00 IRCLK = 1 RSPEN = 1 FO 0 0 RFS0 VDD 1ADDITIONAL Table 11. Serial Port Control Register Setup RCLK0 SCLK DOUTB ADSP-BF53x1 SPORT0 The connection diagram is shown in Figure 45. For signal processing applications, it is imperative that the frame synchronization signal from the TMS320C541 provide equidistant sampling. The VDRIVE pin of the AD7265 takes the same supply voltage as that of the TMS320C541. This allows the ADC to operate at a higher voltage than its serial interface, and therefore, the TMS320C541, if necessary. AD72651 Description Sample data with falling edge of RSCLK Active low frame signal Frame every word Internal RFS used Receive MSB first Zero fill Internal receive clock Receive enabled 16-bit data-word (or may be set to 1101 for 14-bit data-word) TMS320C5411 SCLK CLKX0 CLKR0 CLKX1 CLKR1 DOUTA DR0 DOUTB DR1 CS FSX0 FSR0 VDRIVE FSR1 VDD Table 10. The SPORT0 Receive Configuration 2 Register (SPORT0_RCR2) Setting RXSE = 1 SLEN = 1111 1ADDITIONAL PINS OMITTED FOR CLARITY. Description Secondary side enabled 16-bit data-word (or may be set to 1101 for 14-bit data-word) To implement the power-down modes, SLEN should be set to 1001 to issue an 8-bit SCLK burst. A Blackfin driver for the AD7265 is available to download at www.analog.com. Rev. A | Page 24 of 28 Figure 45. Interfacing the AD7265 to the TMS320C541 04674-038 DOUTA SERIAL DEVICE A (PRIMARY) 04674-037 AD72651 AD7265 The connection diagram in Figure 46 shows how the AD7265 can be connected to the ESSI (synchronous serial interface) of the DSP563xx family of DSPs from Motorola. There are two on-board ESSIs, and each operates in synchronous mode (Bit SYN = 1 in CRB register) with internally generated word length frame sync for both TX and RX (Bit FSL1 = 0 and Bit FSL0 = 0 in CRB). Normal operation of the ESSI is selected by making MOD = 0 in the CRB. Set the word length to 16 by setting Bit WL1 = 1 and Bit WL0 = 0 in CRA. In the example shown in Figure 46, the serial clock is taken from the ESSI0 so the SCK0 pin must be set as an output, SCKD = 1, while the SCK1 pin is set as an input, SCKD = 0. The frame sync signal is taken from SC02 on ESSI0, so SCD2 = 1, while on ESSI1, SCD2 = 0; therefore, SC12 is configured as an input. The VDRIVE pin of the AD7265 takes the same supply voltage as that of the DSP563xx. This allows the ADC to operate at a higher voltage than its serial interface and therefore the DSP563xx, if necessary. DSP563xx1 AD72651 SCLK SCK0 DOUTA SRD0 DOUTB SRD1 SCK1 To implement the power-down modes on the AD7265, the word length can be changed to 8 bits by setting Bit WL1 = 0 and Bit WL0 = 0 in CRA. The FSP bit in the CRB should be set to 1 so the frame sync is negative. It is imperative for signal processing applications that the frame synchronization signal from the DSP563xx provides equidistant sampling. CS SC02 VDRIVE SC12 VDD 1ADDITIONAL PINS OMITTED FOR CLARITY. Figure 46. Interfacing the AD7265 to the DSP563xx Rev. A | Page 25 of 28 04674-039 AD7265 TO DSP563xx AD7265 APPLICATION HINTS GROUNDING AND LAYOUT PCB DESIGN GUIDELINES FOR LFCSP The analog and digital supplies to the AD7265 are independent and separately pinned out to minimize coupling between the analog and digital sections of the device. The printed circuit board (PCB) that houses the AD7265 should be designed so that the analog and digital sections are separated and confined to certain areas of the board. This design facilitates the use of ground planes that can be easily separated. The lands on the chip scale package (CP-32-3) are rectangular. The PCB pad for these should be 0.1 mm longer than the package land length, and 0.05 mm wider than the package land width, thereby having a portion of the pad exposed. To ensure that the solder joint size is maximized, the land should be centered on the pad. To provide optimum shielding for ground planes, a minimum etch technique is generally best. All three AGND pins of the AD7265 should be sunk in the AGND plane. Digital and analog ground planes should be joined in only one place. If the AD7265 is in a system where multiple devices require an AGND to DGND connection, the connection should still be made at one point only, a star ground point that should be established as close as possible to the ground pins on the AD7265. Avoid running digital lines under the device as this couples noise onto the die. However, the analog ground plane should be allowed to run under the AD7265 to avoid noise coupling. The power supply lines to the AD7265 should use as large a trace as possible to provide low impedance paths and reduce the effects of glitches on the power supply line. To avoid radiating noise to other sections of the board, fast switching signals, such as clocks, should be shielded with digital ground, and clock signals should never run near the analog inputs. Avoid crossover of digital and analog signals. To reduce the effects of feedthrough within the board, traces on opposite sides of the board should run at right angles to each other. A microstrip technique is the best method but is not always possible with a double-sided board. In this technique, the component side of the board is dedicated to ground planes, while signals are placed on the solder side. The bottom of the chip scale package has a thermal pad. The thermal pad on the PCB should be at least as large as the exposed pad. On the PCB, there should be a clearance of at least 0.25 mm between the thermal pad and the inner edges of the pad pattern to ensure that shorting is avoided. To improve thermal performance of the package, use thermal vias on the PCB incorporating them in the thermal pad at 1.2 mm pitch grid. The via diameter should be between 0.3 mm and 0.33 mm, and the via barrel should be plated with 1 oz. copper to plug the via. The user should connect the PCB thermal pad to AGND. EVALUATING THE AD7265 PERFORMANCE The recommended layout for the AD7265 is outlined in the evaluation board documentation. The evaluation board package includes a fully assembled and tested evaluation board, documentation, and software for controlling the board from the PC via the evaluation board controller. The evaluation board controller can be used in conjunction with the AD7265 evaluation board, as well as many other Analog Devices, Inc. evaluation boards ending in the CB designator, to demonstrate/evaluate the ac and dc performance of the AD7265. The software allows the user to perform ac (fast Fourier transform) and dc (histogram of codes) tests on the AD7265. The software and documentation are on a CD shipped with the evaluation board. Good decoupling is also important. All analog supplies should be decoupled with 10 μF tantalum capacitors in parallel with 0.1 μF capacitors to GND. To achieve the best results from these decoupling components, they must be placed as close as possible to the device, ideally right up against the device. The 0.1 μF capacitors should have low effective series resistance (ESR) and effective series inductance (ESI), such as the common ceramic types or surface-mount types. These low ESR and ESI capacitors provide a low impedance path to ground at high frequencies to handle transient currents due to internal logic switching. Rev. A | Page 26 of 28 AD7265 OUTLINE DIMENSIONS 0.60 MAX 5.00 BSC SQ 0.60 MAX PIN 1 INDICATOR 25 24 PIN 1 INDICATOR TOP VIEW 0.50 BSC 4.75 BSC SQ 1 3.25 3.10 SQ 2.95 EXPOSED PAD (BOTTOM VIEW) 0.50 0.40 0.30 17 16 9 8 0.25 MIN 3.50 REF 0.80 MAX 0.65 TYP 12° MAX 1.00 0.85 0.80 32 0.05 MAX 0.02 NOM 0.30 0.23 0.18 SEATING PLANE COPLANARITY 0.08 0.20 REF COMPLIANT TO JEDEC STANDARDS MO-220-VHHD-2 Figure 47. 32-Lead Lead Frame Chip Scale Package [LFCSP_VQ] 5 mm × 5 mm Body, Very Thin Quad (CP-32-2) Dimensions shown in millimeters 0.75 0.60 0.45 1.20 MAX 9.00 BSC SQ 25 32 24 1 PIN 1 7.00 BSC SQ TOP VIEW 0.15 0.05 (PINS DOWN) 0° MIN 1.05 1.00 0.95 0.20 0.09 7° 3.5° 0° 0.08 MAX COPLANARITY SEATING PLANE 17 8 9 VIEW A VIEW A 0.80 BSC LEAD PITCH ROTATED 90° CCW 16 0.45 0.37 0.30 COMPLIANT TO JEDEC STANDARDS MS-026ABA Figure 48. 32-Lead Thin Plastic Quad Flat Package [TQFP] (SU-32-2) Dimensions shown in millimeters ORDERING GUIDE Model AD7265BCP AD7265BCPZ 1 AD7265BCPZ-REEL71 AD7265BCPZ-REEL1 AD7265BSUZ1 AD7265BSUZ-REEL71 AD7265BSUZ-REEL1 EVAL-AD7265CB 2 EVAL-CONTROL BRD2 3 1 2 3 Temperature Range –40°C to +125°C –40°C to +125°C –40°C to +125°C –40°C to +125°C –40°C to +125°C –40°C to +125°C –40°C to +125°C Package Description 32-Lead LFCSP_VQ 32-Lead LFCSP_VQ 32-Lead LFCSP_VQ 32-Lead LFCSP_VQ 32-Lead TQFP 32-Lead TQFP 32-Lead TQFP Evaluation Board Control Board Package Option CP-32-2 CP-32-2 CP-32-2 CP-32-2 SU-32-2 SU-32-2 SU-32-2 Z = Pb-free part. This can be used as a standalone evaluation board or in conjunction with the EVAL-CONTROL board for evaluation/demonstration purposes. This board is a complete unit allowing a PC to control and communicate with all Analog Devices, Inc. evaluation boards ending in the CB designators. To order a complete evaluation kit, the particular ADC evaluation board (such as, EVAL-AD7265CB), the EVAL-CONTROL BRD2, and a 12 V transformer must be ordered. See the relevant evaluation board technical note for more information. Rev. A | Page 27 of 28 AD7265 NOTES ©2006 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D04674-0-11/06(A) T T Rev. A | Page 28 of 28