Photologic® Reflective Object Sensor OPB760, OPB761, OPB762, OPB763 (Series N and T) OPB770, OPB771, OPB772, OPB773 (Series NZ and TZ) Features: • Choice of mounting configurations • Choice of four output configurations • .040” (10.160 mm) PCBoard mount (N and T series) • 12” (304.800 mm) AWG 26 wires (NZ and TZ series) OPB760N OPB775TZ Description: The OPB760N, OPB760T, OPB770N and OPB770T series of reflec ve assemblies feature Photologic® output. The electrical output can be specified as either TTL Totem-Pole or TTL Open-Collector, either of which can be supplied with inverter or buffer output polarity. OPB760N and OPB760T series devices are designed for PCBoard moun ng and have 0.04” (10 mm) long leads. OPB760T and OPB770T series devices are designed for remote moun ng with two moun ng tabs. OPB770NZ and OPB770TZ series devices have 12” (305 mm) long, UL approved 26 AWG wires. All devices in this series offer the added stability of a built-in hysteresis amplifier. Custom electrical, wire and cabling and connectors are available. Contact your local representa ve or OPTEK for more informa on. Applications: • • • • • • Non-contact Photologic® reflective object sensor Assembly line automation Machine automation Machine safety End of travel sensor Door sensor Ordering Information Part LED Peak Sensor Reflection Distance Number Wavelength Photologic® (Inch) Min / Max Mounting OPB760N Totem-Pole OPB761N Open Collector OPB762N Inv-Totem-Pole PCBoard .40” OPB763N Inv-Open Collector (10.160 mm) OPB760T Totem-Pole leads) OPB761T Open Collector OPB762T Inv-Totem-Pole OPB763T Inv-Open Collector 890 nm 0.080" / 0.220” OPB770NZ Totem-Pole OPB771NZ Open Collector OPB772NZ Inv-Totem-Pole OPB773NZ Inv-Open Collector 12” (304.800 mm) 26 AWG wire OPB770TZ Totem-Pole OPB771TZ Open Collector OPB772TZ Inv-Totem-Pole OPB773TZ Inv-Open Collector RoHS General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc OPTEK Technology, Inc. 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.ttelectronics.com Issue C 05/2016 Page 1 Photologic® Reflective Object Sensor OPB760, OPB761, OPB762, OPB763 (Series N and T) OPB770, OPB771, OPB772, OPB773 (Series NZ and TZ) Electrical Specifications OPB760, OPB770 Buffered Totem-Pole OPB761, OPB771 Buffered Open Collector VCC VCC OUT OUT GND OPB762, OPB772 Inverted Totem-Pole VCC GND OPB763, OPB773 Inverted Open-Collector VCC OUT OUT GND General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc GND OPTEK Technology, Inc. 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.ttelectronics.com Issue C 05/2016 Page 2 Photologic® Reflective Object Sensor OPB760, OPB761, OPB762, OPB763 (Series N and T) OPB770, OPB771, OPB772, OPB773 (Series NZ and TZ) Electrical Specifications OPB760 (N and T Series) OPB770 (NZ and TZ Series) X = 0.08” [2.0mm] to 0.22” [5.6mm] Pin # Description Pin# Description 1 Cathode 3 Ground 4 Output 5 VCC 2 Anode General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc Color/Pin# [ MILLIMETERS] DIMENSIONS ARE IN: INCHES Description Color/Pin# Description Red-4 Anode White-1 VCC Black-5 Cathode Blue-2 Output Green-3 Ground OPTEK Technology, Inc. 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.ttelectronics.com Issue C 05/2016 Page 3 Photologic® Reflective Object Sensor OPB760, OPB761, OPB762, OPB763 (Series N and T) OPB770, OPB771, OPB772, OPB773 (Series NZ and TZ) Electrical Specifications Absolute Maximum Ratings (TA=25°C unless otherwise noted) Supply Voltage, VCC (not to exceed 3 seconds) 10 V Storage Temperature Range -40° C to +85° C Operating Temperature Range -40° C to +70° C Lead Soldering Temperature (1/16” inch (1.6 mm) from case for 5 seconds with soldering iron)(1) 260° C (2) Input Diode Power Dissipation 100 mW Output Photologic® Power Dissipation(3) 200 mW Total Device Power Dissipation(4) 300 mW Voltage at Output Lead (Open Collector Output) 35 V Diode Forward DC Current 40 mA Diode Reverse DC Voltage 3V Electrical Characteristics (TA = 25°C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Input Diode VF Forward Voltage - - 1.8 V IF = 40 mA, TA = 25° C IR Reverse Current - - 100 μA VR = 2.0 V, TA = 25° C 4.75 - 5.25 V Output Photologic® Sensor VCC Operating DC Supply Voltage ICCL Low Level Supply Current: Buffered Totem-Pole Output(5)(6) Buffered Open-Collector Output(5)(6) - - 10 10 mA mA Inverted Totem-Pole Output(5) Inverted Open-Collector Output(5) - - 10 10 mA mA Vcc = 5.25 V, If = 25 mA (output open) High Level Supply Current: Buffered Totem-Pole Output(5)(6) Buffered Open-Collector Output(5) - - 10 10 mA mA Vcc = 5.25 V, If = 25 mA (output open) Inverted Totem-Pole Output(5)(6) Inverted Open-Collector Output(5)(6) - - 10 10 mA mA Vcc = 5.25 V, If = 0 mA (output open) High Level Output Current: Buffered Open-Collector Output - - 100 100 μA μA Vcc = 4.5 V, If = 25 mA, VOH = 30 V, TA=25°C Inverted Open-Collector Output - - 100 μA Vcc = 4.5 V, If = 0 mA, VOH = 30 V, TA = 25°C ICCH IOH Notes: (1) (2) (3) (4) (5) (6) (7) Vcc = 5.25 V, If = 0 mA (output open) RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering. Derate linearly 2.22 mW/°C above 25° C. Derate linearly 4.44 mW/°C above 25° C. Derate linearly 6.66 mW/°C above 25° C.Normal application would be with light source blocked, simulated by IF=0 mA. Tested at d = 0.080” (mm) from a 90% diffuse white test surface. Normal application would be with light source blocked, simulated by IF = 0 mA. All parameters tested using pulse technique. General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc OPTEK Technology, Inc. 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.ttelectronics.com Issue C 05/2016 Page 4 Photologic® Reflective Object Sensor OPB760, OPB761, OPB762, OPB763 (Series N and T) OPB770, OPB771, OPB772, OPB773 (Series NZ and TZ) Electrical Specifications Electrical Characteristics (TA = 25°C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS - - 25 mA Hysteresis(2) 1.1 - 2.0 - Short Circuit Output Current: Buffered Totem-Pole Output(1) -15 - -100 mA Inverted Totem-Pole Output(1) -15 - -100 mA Low Level Output Voltage: Buffered Totem-Pole Output(1)(4) Buffered Open-Collector Output(1)(4) - - 0.4 0.4 V V VCC = 4.5 V, IOL = 12.8 mA, IF = 0 mA or IF = 30 mA Inverted Totem-Pole Output Inverted Open-Collector Output(1)(4) - - 0.4 0.4 V V VCC = 4.5 V, IOL = 12.8 mA, IF = 25 mA High Level Output Voltage: Buffered Totem-Pole Output(1) 2.4 - - V Inverted Totem-Pole Output(1)(4) 2.4 - - V VCC = 4.5 V, IOH = -800 μA, IF = 0 mA Inverted Totem-Pole Output (3) Inverted Open-Collector Output(3) 2.4 2.4 - - V V VCC = 4.5 V, IOH = -800 μA, IF = 30 mA Output Photologic® Sensor (continued) IF(+) IF(+)/IF(-) IOS VOL VOH LED Positive-Going Threshold Current(2) Vcc = 5 V, TA = 25° C Vcc = 5 V If = 25 mA, Vcc = 5.25 V, Output = GRD If = 0 mA, Vcc = 5.25 V, Output = GRD VCC = 4.5 V, IOH = -800 μA, IF = 25 mA Notes: (1) Tested at d = 0.080” (mm) from a 90% diffuse white test surface. (2) Tested at d = 0.080” (mm), 0.150” (mm) and 0.220” (mm) from a 90% diffuse white test surface. Reference: Eastman Kodak, Catalog #E 152 7795. (3) Tested at d = 0.080” (mm), 0.150” (mm) and 0.220” (mm) from a 5% diffuse black test surface. (4) Normal application would be with light source blocked, simulated by IF=0 mA. (5) OPB760N through OPB763N series devices are terminated with 0.20” (mm) square leads designed for printed PCBoard mounting. (6) OPB770NZ through OPB773NZ series devices are terminated with 12 inches (mm) of 7-strand 26 AWG UL1429 insulated wire on each terminal. A standard AMP No. 640442-5 connector has been attached to the lead wires to ease connection to wire harnesses. (7) OPB760T through OPB763T series devices are terminated with 0.020” (mm) square leads designed for printed PCBoard mounting. (8) OPB770TZ through OPB773TZ series are terminated with 12” (mm) of 7-strand 26 AWG UL1429 insulated wire on each terminal. A standard AMP No. 640442-5 connector has been attached to the lead wires to ease connection to wire harnesses. (9) All parameters tested using pulse technique. General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc OPTEK Technology, Inc. 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.ttelectronics.com Issue C 05/2016 Page 5 Photologic® Reflective Object Sensor OPB760, OPB761, OPB762, OPB763 (Series N and T) OPB770, OPB771, OPB772, OPB773 (Series NZ and TZ) Performance Logic Level vs Distance 1 1 1 1 1 Kodak 90% - Towards Logic Logic Logic Level vs Distance 1 1 Copy Paper - Towards 1 Kodak 90% - Away Copy Paper - Away 0 0 0 0 0 0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.0 0.1 0.2 Distance (inches) 0.3 0.4 0.5 0.6 0.5 0.6 Distance (inches) Logic Level vs Distance Logic Level vs Distance 1 1 1 1 1 1 Logic Logic Kodak 19% - Towards 1 1 Avery Labels - Towards Kodak 19% - Away 0 0 Avery Labels - Away 0 0 0 0 0.0 0.1 0.2 0.3 0.4 0.5 Distance (inches) General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc 0.6 0.0 0.1 0.2 0.3 0.4 Distance (inches) OPTEK Technology, Inc. 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.ttelectronics.com Issue C 05/2016 Page 6 Photologic® Reflective Object Sensor OPB760, OPB761, OPB762, OPB763 (Series N and T) OPB770, OPB771, OPB772, OPB773 (Series NZ and TZ) Performance Typical Trigger Current and Hysteresis Ratio vs Ambient Temperature Logic Level vs Distance 1 14 IF (+), IF(-) and IF(+)/IF(-) - Trigger Current and Hysteresis Ratio IF(+) mA 1 Logic 1 Retro 3M 3870 - Towards 1 0 Retro 3M 3870 - Away 0 IF(-) mA 12 Hys 10 8 6 4 2 0 0 0.0 0.1 0.2 0.3 0.4 0.5 -40 -30 -20 -10 0.6 Distance (inches) Output Voltage vs Ambient Temperature 10 20 30 40 50 60 70 80 Supply Current vs Ambient Temperature 18 9 16 8 14 7 12 6 Typical Icc (mA) Typical Output Voltage (V) 0 Ta - Ambient Temperature (°C) 10 8 5 4 3 6 4 2 Voh (V) Vol (V) 2 Icch(mA) Iccl(mA) 1 0 0 -40 -20 0 20 40 60 Ta -Ambient Temperature - (°C) General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc 80 -40 -20 0 20 40 60 80 Ta -Ambient Temperature - (°C) OPTEK Technology, Inc. 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.ttelectronics.com Issue C 05/2016 Page 7