HMC394LP4 / 394LP4E v08.0607 FREQUENCY DIVIDERS & DETECTORS - SMT 6 GaAs HBT PROGRAMMABLE 5-BIT COUNTER, DC - 2.2 GHz Typical Applications Features Programmable divider for offset synthesizer and variable divide by N applications: SSB Phase Noise: -153 dBc/Hz @ 100 kHz • Satellite Communication Systems Parallel 5-Bit Control • Point-to-Point and Point-to-Multi-Point Radios Wide Input Power Range: -20 to +10 dBm • LMDS 4mm x 4mm Leadless SMT Package Selectable Division from 2 to 32 • SONET Functional Diagram General Description The HMC394LP4 & HMC394LP4E are low noise GaAs HBT programmable 5-bit counters in 4mm x 4mm leadless surface mount packages. This device allows continuous division from N= 2 to 32 at input frequencies up to 2.2 GHz. The output voltage swing is 800 mV with a duty cycle inversely proportional to N. The low additive SSB phase noise of -153 dBc/Hz at 100 KHz offset makes this counter an excellent choice for low noise synthesizer applications. Electrical Specifications, TA = +25° C, 50 Ohm System, Vcc= 5V Parameter Conditions Maximum Input Frequency Sine Wave Input [1] Input Power Range Fin = 0.1 to 2.2 GHz SSB Phase Noise Typ. Max. 2.2 Minimum Input Frequency Output Power Min. -15 GHz >-20 0.1 GHz +10 dBm Divide-by-2 4 dBm Fin = 1 GHz, N = 4 -153 dBc/Hz Output Transition Time 100 ps Supply Current (Icc) 194 mA 1. Divider will operate down to DC for square-wave input signal. 6 - 50 Units For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC394LP4 / 394LP4E v08.0607 GaAs HBT PROGRAMMABLE 5-BIT COUNTER, DC - 2.2 GHz Input Sensitivity Window vs. Temperature, N= 16, T= -40 °C to +85 °C 20 10 10 0 Recommended Operating Window -10 -20 6 0 -10 -20 -30 -30 0 0.5 1 1.5 2 2.5 3 0 0.5 1 INPUT FREQUENCY (GHz) 2 2.5 3 SSB Phase Noise Performance, Fin= 1 GHz, N= 4, T= 25 °C Output Power, 5 Major Divide Ratio States, T= 25 °C 10 -60 N=2 N=4 -70 0 SSB PHASE NOISE (dBc/Hz) 5 Output Power (dBm) 1.5 INPUT FREQUENCY (GHz) N=8 -5 N=16 -10 N=32 -15 -80 -90 -100 -110 -120 -130 -140 -150 -20 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 2 2.2 2.4 -160 2 10 3 10 INPUT FREQUENCY (GHz) 5 6 10 10 7 10 OFFSET FREQUENCY (Hz) Fundamental Feedthru Power, Pin= 0 dBm, T= 25 °C Typical Supply Current vs. Vcc 0 -10 OUTPUT LEVEL (dBm) 4 10 -20 Vcc (V) Icc (mA) 4.75 176 5.0 194 5.25 210 FREQUENCY DIVIDERS & DETECTORS - SMT 20 INPUT POWER (dBm) INPUT POWER (dBm) Input Sensitivity Window, 5 major Divide Ratio States, T= 25 °C Note: Divider will operate over full voltage range shown above. -30 N=2 N=4 N=8 N=16 N=32 -40 -50 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 2 2.2 2.4 INPUT FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 6 - 51 HMC394LP4 / 394LP4E v08.0607 GaAs HBT PROGRAMMABLE 5-BIT COUNTER, DC - 2.2 GHz 2nd Harmonic, Pin= 0 dBm, T= 25 °C 0 0 -5 OUTPUT LEVEL (dBm) OUTPUT LEVEL (dBm) N=2 -10 N=4 N=8 -15 -20 0.4 0.6 0.8 1 N=16 N=32 1.2 1.4 1.6 1.8 2 2.2 N=32 -15 N=16 0.6 0.8 0 N=16 N=32 1.4 1.6 1.8 2 2.2 2.4 2 2.2 2.4 68 70 -5 OUTPUT LEVEL (dBm) OUTPUT LEVEL (dBm) 1.2 0 N=2 N=8 -5 -10 -15 -20 -25 -10 -15 -20 N=2 N=4 N=8 -25 0.6 0.8 1 1.2 1.4 1.6 1.8 2 2.2 -30 0.4 2.4 0.6 0.8 INPUT FREQUENCY (GHz) 1 N=16 N=32 1.2 1.4 1.6 1.8 INPUT FREQUENCY (GHz) Output Voltage Wavform, Fin= 1 GHz, N= 2, Pin= 0 dBm, T= 25 °C Output Voltage Wavform, Fin= 1 GHz, N= 17, Pin= 0 dBm, T= 25 °C 500 200 400 AMPLITUDE (mV) 300 100 0 -100 -300 38 1 5th Harmonic, Pin= 0 dBm, T= 25 °C -200 300 200 100 0 38.5 39 39.5 TIME (nS) 6 - 52 -10 INPUT FREQUENCY (GHz) 4th Harmonic, Pin= 0 dBm, T= 25 °C -30 0.4 N=8 -5 -20 0.4 2.4 N=4 INPUT FREQUENCY (GHz) AMPLITUDE (mV) FREQUENCY DIVIDERS & DETECTORS - SMT 6 3rd Harmonic, Pin= 0 dBm, T= 25 °C 40 40.5 41 -100 48 50 52 54 56 58 60 62 64 66 TIME (nS) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC394LP4 / 394LP4E v08.0607 GaAs HBT PROGRAMMABLE 5-BIT COUNTER, DC - 2.2 GHz Absolute Maximum Ratings +13 dBm Vcc +5.5V VLogic -1.6 to -1.2 Vcc Maximum Channel Temperature 135 °C Continuous Pdiss (T = 85 °C) (derate 55 mW/°C above 85 °C) 1.155 W Storage Temperature -65 to +150 °C Operating Temperature -55 to +85 °C ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS 6 FREQUENCY DIVIDERS & DETECTORS - SMT RF Input (Vcc = +5V) Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Package Information Part Number Package Body Material Lead Finish MSL Rating HMC394LP4 Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 HMC394LP4E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 Package Marking [3] [1] H394 XXXX [2] H394 XXXX [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 6 - 53 HMC394LP4 / 394LP4E v08.0607 GaAs HBT PROGRAMMABLE 5-BIT COUNTER, DC - 2.2 GHz Pin Description FREQUENCY DIVIDERS & DETECTORS - SMT 6 6 - 54 Pin Number Function Description 1-5 AO - A4 CMOS compatible control input bit 0 (LSB) - 4. 6, 9, 10, 11, 12, 15, 18, 19, 20, 21, 22 GND Ground: Backside of package has exposed metal ground slug which must be connected to ground. 7, 8, 23, 24 VCC Supply voltage 5V ± 0.25V must be applied to all four pins. 13 IN RF input 180° out of phase with pin 14 must be AC ground. 14 IN RF input must be DC blocked. 16 OUT Divided output pulse. 17 OUT Divided output pulse 180° out of phase with pin 16. Interface Schematic For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC394LP4 / 394LP4E v08.0607 GaAs HBT PROGRAMMABLE 5-BIT COUNTER, DC - 2.2 GHz HMC394LP4 Programming Truth Table A1 A2 A3 A4 Output Low 0 0 0 0 0 /2 1 0 0 0 0 /3 0 1 0 0 0 /4 1 1 0 0 0 - - - - - - / 32 1 1 1 1 1 Note: A0 through A4 are CMOS compatible logic control inputs. Application Circuit, (2 GHz - Divide-by-20) 6 FREQUENCY DIVIDERS & DETECTORS - SMT (LSB) A0 Function * Note: Mount bypass capacitors as close to pins as possible. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 6 - 55 HMC394LP4 / 394LP4E v08.0607 GaAs HBT PROGRAMMABLE 5-BIT COUNTER, DC - 2.2 GHz Evaluation PCB FREQUENCY DIVIDERS & DETECTORS - SMT 6 The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and backside ground slug should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. List of Materials for Evaluation PCB 104898 [1] Item Description Function S1 S2 S3 S4 S5 J1 - J3 PCB Mount SMA RF Connector Output Low 0 0 0 0 0 C1 - C2 [2] 1.0 μF Tantalum Capacitor /2 1 0 0 0 0 C3 - C4 [2] .01 μF Capacitor, 0603 Pkg. /3 0 1 0 0 0 C5 - C8 1000 pF Capacitor, 0603 Pkg. /4 1 1 0 0 0 R1* Resistor SIP 10 K ohm - - - - - - S1 - S6 Jumper (shunt) 2mm / 32 1 1 1 1 1 U1 HMC394LP4 / HMC394LP4E 5-Bit Counter Note: 0 = Jumper Installed. 1 = Jumper Not Installed. PCB 104435 Eval Board [1] Reference this number when ordering complete evaluation PCB [2] Optional components. 6 - 56 HMC394LP4 Evaluation PCB Truth Table Note: The evaluation PCB for the HMC394LP4 contains 10K Ohm pull up resistors for each of the five control inputs A0 through A4. Programming the 31 distinct division ratios consists of installing or removing jumpers S1 through S5, as shown above. Jumper S6 must always be installed to provide ground to pin 20. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC394LP4 / 394LP4E v08.0607 GaAs HBT PROGRAMMABLE 5-BIT COUNTER, DC - 2.2 GHz Applications Information Asynchronous Programming The 5-Bit programmable counter counts-down from the programmed value of the data bits to zero and issues an output pulse at the end of each cycle. Settling time of the programmable 5-Bit counter is defined as the maximum time required for the counter to change the division ratio N to a new value after the data bits have settled. The worst case settling time occurs if the data bits A0 thru A4 are changing during the load cycle. Under this condition, the data bits may potentially be erroneous when they are clocked in and in the worst case could be all 1’s, requiring 32 clock cycles until the correct data is re-loaded into the flip flops. The worst case asynchronous settling time can be calculated as follows: TSETTLING MAX = 32/fIN (For Asynchronous Programming) 6 FREQUENCY DIVIDERS & DETECTORS - SMT Simplified Block Diagram As an example, if the input frequency is 1 GHz, the maximum settling time is 32 nS For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 6 - 57 HMC394LP4 / 394LP4E v08.0607 GaAs HBT PROGRAMMABLE 5-BIT COUNTER, DC - 2.2 GHz Synchronous Programming FREQUENCY DIVIDERS & DETECTORS - SMT 6 For applications which can not tolerate a momentary undefined division ratio, which normally occurs while changing the data bits (A0-A4) at random, synchronous programming can be used. Data is loaded into the counter on every rising edge of the clock which occurs while the output (OUT) is “HIGH”. The typical minimum setup and hold times are shown in the table below as a function of frequency. For precision applications, the rising edge of the complementary output may be used to latch the new data bits (A0-A4), so that all bits are settled before the next load cycle. TSETTLING MAX = N/fIN (For Synchronous Programming) Where N is the desired division ratio, and fIN = Input Frequency (Hz) Parameter 0.5 GHz 1 GHz 2 GHz tSETUP 200 ps 200 ps 200 ps tHOLD 700 ps 300 ps 120 ps Programmable Divider Timing Requirements for Synchronous Programming t SU OUT t Rising Edge to Clock New Data OUT A0-A4 HOLD CURRENT DATA NEW DATA IN Data Load Rising Edge 6 - 58 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC394LP4 / 394LP4E v07.0705 GaAs HBT PROGRAMMABLE 5-BIT COUNTER, DC - 2.2 GHz CMOS/TTL Input Characteristics Maximum Input Logic “0” Voltage (VIL MAXIMUM) = 1.1V @ 10 uA. 6 Input IV characteristics for the logic inputs (A0-A4) are shown below: 0.4 V Input Current (mA) 0.2 V IL MAX IH MIN 0 -0.2 -0.4 -0.6 -0.8 0 1 2 3 4 5 Input Voltage (V) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com FREQUENCY DIVIDERS & DETECTORS - SMT Minimum Input Logic “1” Voltage (VIH MINIMUM) = 1.8V @ 500 uA. 6 - 59