MN103SE3 Series Type Internal ROM type MN103SE3K MN103SFE3K Mask ROM FLASH ROM (byte) 256K RAM (byte) 8K QFP100-P-1818B Package (Lead-free) Minimum Instruction Execution Time 16.7 ns (4.5 V to 5.5 V) Interrupts 9 external interrupts 47 internal interrupts: Watchdog timer. Timer. Serial I/F. PWM. A/D conversion finish. System error Timer Counter 8-bit timer × 12 Timer 0 to 7, 14 to 17 Interval timer. Event count. Cascading connectable 16-bit timer × 6 Timer 8 to 10 .........Interval timer. Event count. PWM output. Double buffer Timer 11 ................Interval timer. Event count. PWM output (6 pins simultaneous output are available). Double buffer Timer 12, 13 ..........Interval timer. Double buffer. Start synchronized with 3-phase PWM are available Watchdog timer × 1 Serial interface UART (full duplex) /Synchronous interfaces selective × 3 Serial 0, 1...............7-bit, 8-bit transmission Serial 2...................1-bit to 8-bit transmission (synchronous). 2 and 3 channel type selectable (synchronous) I/O Pins I/O 81 : Common use × 81 A/D converter 10-bit × 3 unit. 20 channels Minimum conversion time: 1.0 µs Simultaneous conversion of 3 series are available Conversion start synchronized with 3-phase PWM or timer 12, 13 are available Motor Control PWM 16-bit 3-phase PWM × 2 Triangular waveform or jigsaw waveform. Dead time setup. Double buffer. Output polar switching is available. PWM output pin protect function Electrical Charactreistics (A/D converter characteristics) Parameter Symbol Condition min 10-bit Non-linear error A/D conversion time TAD 1.0 Analog input voltage VIA VSS Limit typ max ±3 Unit LSB µs VDD V Ta = 25 °C. VDD = 5.0 V. VSS = 0 V MAF00028EEM MN103SE3K, MN103SFE3K Pin Assignment 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 P45, TM10BO P44, TM10AO P43, TM9BIO P42, TM9AIO P41, TM9BO P40, TM9AO P37, TM8BIO P36, TM8AIO VSS P35, TM5IO VDD P34, TM4IO P33, TM3IO P32, TM2IO P31, TM1IO P30, TM0IO P27, SBI0 P26, SBT0 P25, SBO0 P24, SBI1 P23, SBT1 P22, SBO1 P21, SBI2 P20, SBT2 P17, SBO2 QFP100-P-1818B 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 P76, TM11O4 P77, TM11O5 P80, IRQ00 P81, IRQ01 P82, IRQ02 P83, IRQ03 P84, TM14IO TCPOUT P86 P87 P90, ADIN00 P91, ADIN01 P92, ADIN02 P93, ADIN03 VSS P94, ADIN04 VDD P95, ADIN05 P96, ADIN06 P97, ADIN07 PA0, ADIN08 PA1, ADIN09 PA2, ADIN10 PA3, ADIN11 PA4, ADIN12 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 P46, TM10AIO P47, TM10BIO P50, TM6IO P51, TM7IO P52, PWM00 P53, NPWM00 P54, PWM01 P55, NPWM01 P56, PWM02 P57, NPWM02 P60 P61 P62, PWM10 P63, NPWM10 P64, PWM11 P65, NPWM11 P66, PWM12 P67, NPWM12 VDD P72, TM11IO0 VSS P73, TM11IO1 VDD2 P74, TM11O2 P75, TM11O3 MAF00028EEM 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 P16, TM17IO P15, TM16IO NRST P14, IRQ08 P13, IRQ07 P12, IRQ06 P11, IRQ05 P10, IRQ04 VDD2 VDD VDD VPPEX VSS OSCI OSCO PB3, ADIN19 PB2, ADIN18 TEST3 TEST2 TEST1 PB1, ADIN17 PB0, ADIN16 PA7, ADIN15 PA6, ADIN14 PA5, ADIN13 Request for your special attention and precautions in using the technical information and semiconductors described in this book (1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and regulations of the exporting country, especially, those with regard to security export control, must be observed. (2) The technical information described in this book is intended only to show the main characteristics and application circuit examples of the products. No license is granted in and to any intellectual property right or other right owned by Panasonic Corporation or any other company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other company which may arise as a result of the use of technical information described in this book. (3) The products described in this book are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: – Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. – Any applications other than the standard applications intended. (4) The products and product specifications described in this book are subject to change without notice for modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions (operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS, thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages. (7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of our company. 20080805