ES2AA THRU ES2JA 2.0 AMPS. Super Fast Surface Mount Rectifiers Voltage Range 50 to 600 Volts Current 2.0 Amperes SMA/DO-214AC Features Glass passivated junction chip For surface mounted application Low profile package Built-in strain relief Ideal for automated placement Easy pick and place Superfast recovery time for high efficiency Glass passivated chip junction High temperature soldering: O 260 C/10 seconds at terminals Plastic material used carries Underwriters Laboratory Classification 94V-O .062(1.58) .050(1.27) .111(2.83) .090(2.29) .187(4.75) .160(4.06) .103(2.61) .078(1.99) .012(.31) .006(.15) Mechanical Data Cases: Molded plastic Terminals: Solder plated Polarity: Indicated by cathode band Packing: 12mm tape per E1A STD RS-481 Weight: 0.093 gram .008(.20) .004(.10) .056(1.41) .035(0.90) .210(5.33) .195(4.95) Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol ES ES ES ES ES ES ES ES Units Type Number 2AA 2BA 2CA 2DA 2FA 2GA 2HA 2JA Maximum Recurrent Peak Reverse 50 100 150 200 300 400 500 600 V VRRM Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current See Fig. 1 Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 2.0A Maximum DC Reverse Current @TA =25℃ at Rated DC Blocking Voltage @ TA=100℃ Maximum Reverse Recovery Time ( Note 1 ) Typical Junction Capacitance ( Note 2 ) Maximum Thermal Resistance (Note 3) Operating Temperature Range Storage Temperature Range VRMS VDC I(AV) 35 50 70 100 105 150 IFSM 140 200 210 300 350 500 420 600 V V 2.0 A 50 A 0.95 VF 280 400 1.3 1.7 V IR 10 350 uA uA Trr 35 nS Cj RθJA RθJL 25 20 75 20 -55 to +150 -55 to + 150 TJ TSTG Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1 MHz and Applied VR=4.0 Volts 3. Units Mounted on P.C.B. 0.2" x 0.2" (5.0 x 5.0mm) Pad Areas - 172 - pF ℃/W ℃ ℃ RATINGS AND CHARACTERISTIC CURVES (ES2AA THRU ES2JA) FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE FIG.2- MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 60 PEAK FORWARD SURGE CURRENT. (A) AVERAGE FORWARD CURRENT. (A) 3.0 RESISTIVE OR INDUCTIVE LOAD 0.2X0.2"(5.0X5.0mm) COPPER PAD AREAS 2.0 1.0 0 80 90 100 110 120 130 140 8.3ms Single Half Sine Wave o (JEDEC Method) at TL=120 C 50 40 30 20 10 0 150 NUMBER OF CYCLES AT 60Hz FIG.3- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 60 100 10 1 o LEAD TEMPERATURE. ( C) FIG.4- TYPICAL REVERSE CHARACTERISTICS 1000 0 A- JA ES 2F A- GA 2A A- DA INSTANTANEOUS REVERSE CURRENT. ( A) 10 ES 2H 1 ES INSTANTANEOUS FORWARD CURRENT. (A) Tj=25 C PULSE WIDTH-300 S 1% DUTY CYCLE 0.1 0.01 0.4 0.8 1.0 1.2 1.4 1.6 10 Tj=85 0C 1 Tj=25 0C 0.1 0 1.8 FIG.5- TYPICAL JUNCTION CAPACITANCE Tj=25 0C f=1.0MHz Vsig=50mVp-p 50 40 ES 30 2A A-D A 20 ES 2FA -JA 10 0 1 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 60 JUNCTION CAPACITANCE.(pF) Tj=125 0C 0.01 0.6 FORWARD VOLTAGE. (V) 0 100 10 100 REVERSE VOLTAGE. (V) - 173 -