ADS8343 ADS8 343 SBAS183C – JANUARY 2001 – REVISED APRIL 2003 16-Bit, 4-Channel Serial Output Sampling ANALOG-TO-DIGITAL CONVERTER FEATURES DESCRIPTION ● BIPOLAR INPUT RANGE The ADS8343 is a 4-channel, 16-bit sampling Analog-toDigital (A/D) converter with a synchronous serial interface. Typical power dissipation is 8mW at a 100kHz throughput rate and a +5V supply. The reference voltage (VREF) can be varied between 500mV and VCC/2, providing a corresponding input voltage range of ±VREF. The device includes a shutdown mode which reduces power dissipation to under 15µW. The ADS8343 is ensured down to 2.7V operation. ● PIN-FOR-PIN COMPATIBLE WITH THE ADS7841 AND ADS8341 ● SINGLE SUPPLY: 2.7V to 5V ● 4-CHANNEL SINGLE-ENDED OR 2-CHANNEL DIFFERENTIAL INPUT ● UP TO 100kHz CONVERSION RATE Low power, high speed, and an onboard multiplexer make the ADS8343 ideal for battery-operated systems such as personal digital assistants, portable multi-channel data loggers, and measurement equipment. The serial interface also provides low-cost isolation for remote data acquisition. The ADS8343 is available in an SSOP-16 package and is ensured over the –40°C to +85°C temperature range. ● 86dB SINAD ● SERIAL INTERFACE ● SSOP-16 PACKAGE APPLICATIONS ● ● ● ● ● DATA ACQUISITION TEST AND MEASUREMENT INDUSTRIAL PROCESS CONTROL PERSONAL DIGITAL ASSISTANTS BATTERY-POWERED SYSTEMS SAR DCLK CS CH0 CH1 CH2 Comparator Four Channel Multiplexer Serial Interface and Control CDAC CH3 SHDN DIN DOUT BUSY COM VREF Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright © 2001-2003, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. www.ti.com PACKAGE/ORDERING INFORMATION PRODUCT MAXIMUM INTEGRAL LINEARITY ERROR (LSB) NO MISSING CODES ERROR (LSB) ADS8343E 8 " " ADS8343EB " PACKAGE-LEAD PACKAGE DESIGNATOR(1) SPECIFIED TEMPERATURE RANGE 14 SSOP-16 DBQ –40°C to +85°C ADS8343E Rails, 100 " " " " ADS8343E/2K5 Tape and Reel, 2500 6 15 SSOP-16 DBQ –40°C to +85°C ADS8343EB Rails, 100 " " " " " ADS8343EB/2K5 Tape and Reel, 2500 ORDERING NUMBER TRANSPORT MEDIA, QUANTITY NOTE: (1) For the most current specifications and package information, refer to our web site at www.ti.com. ABSOLUTE MAXIMUM RATINGS(1) PIN CONFIGURATIONS +VCC to GND ........................................................................ –0.3V to +6V Analog Inputs to GND ............................................ –0.3V to +VCC + 0.3V Digital Inputs to GND ........................................................... –0.3V to +6V Power Dissipation .......................................................................... 250mW Maximum Junction Temperature ................................................... +150°C Operating Temperature Range ........................................ –40°C to +85°C Storage Temperature Range ......................................... –65°C to +150°C Lead Temperature (soldering, 10s) ............................................... +300°C Top View NOTE: (1) Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. Exposure to absolute maximum conditions for extended periods may affect device reliability. ELECTROSTATIC DISCHARGE SENSITIVITY This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. SSOP +VCC 1 16 DCLK CH0 2 15 CS CH1 3 14 DIN CH2 4 13 BUSY 12 DOUT ADS8343 CH3 5 COM 6 11 GND SHDN 7 10 GND VREF 8 9 +VCC ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PIN DESCRIPTIONS 2 PIN NAME DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 +VCC CH0 CH1 CH2 CH3 COM SHDN VREF +VCC GND GND DOUT BUSY DIN CS DCLK Power Supply, 2.7V to 5V Analog Input Channel 0 Analog Input Channel 1 Analog Input Channel 2 Analog Input Channel 3 Common reference for analog inputs. This pin is typically connected to VREF. Shutdown. When LOW, the device enters a very low power shutdown mode. Voltage Reference Input. See Electrical Characteristic Table for ranges. Power Supply, 2.7V to 5V Ground Ground Serial Data Output. Data is shifted on the falling edge of DCLK. This output is high impedance when CS is HIGH. Busy Output. This output is high impedance when CS is HIGH. Serial Data Input. If CS is LOW, data is latched on rising edge of DCLK. Chip Select Input. Controls conversion timing and enables the serial input/output register. External Clock Input. This clock runs the SAR conversion process and synchronizes serial data I/O. Maximum input clock frequency equals 2.4MHz to achieve 100kHz sampling rate. ADS8343 www.ti.com SBAS183C ELECTRICAL CHARACTERISTICS: +5V At TA = –40°C to +85°C, +VCC = +5V, VREF = +2.5V, fSAMPLE = 100kHz, and fCLK = 24 • fSAMPLE = 2.4MHz, unless otherwise noted. ADS8343E PARAMETER CONDITIONS MIN TYP RESOLUTION ANALOG INPUT Full-Scale Input Span Absolute Input Range Positive Input-Negative Input Positive Input Negative Input POWER-SUPPLY REQUIREMENTS +VCC Quiescent Current ✻ ✻ ✻ 1.0 20 3 +4.75V < VCC < 5.25V ±8 ±2 8.0 ±0.05 4.0 ✻ ✻ ✻ ✻ = = = = 5Vp-p 5Vp-p 5Vp-p 5Vp-p at at at at 0.024 0 2.4 2.4 0.5 ✻ ✻ Specified Performance 4.75 100 3 7.5 –40 Clk Cycles Clk Cycles kHz ns ns ps MHz MHz MHz ✻ ✻ V GΩ µA µA µA ✻ 5.5 +0.8 1.5 150 Bits LSB mV LSB(1) % LSB µVrms LSB(1) dB dB dB dB ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ 0.4 Binary Two’s Complement Power Dissipation ±6 ±1 ✻ ±0.024 ✻ ✻ ✻ ✻ CMOS 3.0 –0.3 3.5 V V V pF µA ✻ ✻ ✻ ✻ +VCC/2 5 40 2.5 0.001 | IIH | ≤ +5µA | IIL | ≤ +5µA IOH = –250µA IOL = 250µA ✻ ✻ ✻ ✻ –95 86 97 100 DCLK Static Bits ✻ ✻ ✻ ✻ 500 30 100 2.4 10kHz 10kHz 10kHz 50kHz ✻ ✻ 100 VIN VIN VIN VIN UNITS ✻ 16 4.5 SHDN = VDD MAX 15 2.3 fSAMPLE = 10kHz Power-Down Mode(3, 4), CS = +VCC TEMPERATURE RANGE Specified Performance TYP ✻ ✻ 14 fSAMPLE = 12.5kHz DCLK Static DIGITAL INPUT/OUTPUT Logic Family Logic Levels VIH VIL VOH VOL Data Format +VREF +VCC + 0.2 +VCC + 0.2 –VREF –0.2 –0.2 Data Transfer Only REFERENCE INPUT Range Resistance Input Current MIN 25 ±1 SAMPLING DYNAMICS Conversion Time Acquisition Time Throughput Rate Multiplexer Settling Time Aperture Delay Aperture Jitter Internal Clock Frequency External Clock Frequency DYNAMIC CHARACTERISTICS Total Harmonic Distortion(2) Signal-to-(Noise + Distortion) Spurious-Free Dynamic Range Channel-to-Channel Isolation MAX 16 Capacitance Leakage Current SYSTEM PERFORMANCE No Missing Codes Integral Linearity Error Bipolar Error Bipolar Error Match Gain Error Gain Error Match Noise Power-Supply Rejection ADS8343EB 5.25 2.0 ✻ ✻ ✻ ✻ ✻ V mA µA µA mW ✻ °C ✻ 3 10 +85 ✻ V V V V ✻ Same specifications as ADS8343E. NOTES: (1) LSB means Least Significant Bit. With VREF equal to +2.5V, one LSB is 76µV. (2) First nine harmonics of the test frequency. (3) Auto power-down mode (PD1 = PD0 = 0) active or SHDN = GND. (4) Power-down after conversion mode with external clock gated ‘HIGH’. ADS8343 SBAS183C www.ti.com 3 ELECTRICAL CHARACTERISTICS: +2.7V At TA = –40°C to +85°C, +VCC = +2.7V, VREF = +1.25V, fSAMPLE = 100kHz, and fCLK = 24 • fSAMPLE = 2.4MHz, unless otherwise noted. ADS8343E PARAMETER CONDITIONS MIN TYP RESOLUTION ANALOG INPUT Full-Scale Input Span Absolute Input Range SAMPLING DYNAMICS Conversion Time Acquisition Time Throughput Rate Multiplexer Settling Time Aperture Delay Aperture Jitter Internal Clock Frequency External Clock Frequency MAX MIN TYP 16 Positive Input-Negative Input Positive Input Negative Input +VREF +VCC + 0.2 +VCC + 0.2 –VREF –0.2 –0.2 Capacitance Leakage Current SYSTEM PERFORMANCE No Missing Codes Integral Linearity Error Bipolar Error Bipolar Error Match Gain Error Gain Error Match Noise Power-Supply Rejection ADS8343EB ✻ ✻ ✻ 14 1.0 20 3 ±12 ±1 4.0 ±0.05 4.0 ✻ ✻ ✻ ✻ BITS ✻ ✻ ✻ V V V pF µA ±8 ±0.5 ✻ ±0.0024 ✻ ✻ 16 ✻ 4.5 ✻ 100 ✻ ✻ ✻ ✻ 500 30 100 2.4 When Used with Internal Clock Data Transfer Only ✻ 15 1.2 SHDN = VDD UNITS ✻ ✻ 25 ±1 +2.7 < VCC < +3.3V MAX 0.024 0.024 0 2.4 2.0 2.4 ✻ ✻ ✻ ✻ ✻ ✻ Bits LSB mV LSB % of FSR LSB µVrms LSB(1) Clk Cycles Clk Cycles kHz ns ns ps MHz MHz MHz MHz DYNAMIC CHARACTERISTICS Total Harmonic Distortion(2) Signal-to-(Noise + Distortion) Spurious-Free Dynamic Range Channel-to-Channel Isolation REFERENCE INPUT Range Resistance Input Current VIN = 2.5Vp-p at 1kHz VIN = 2.5Vp-p at 1kHz VIN = 2.5Vp-p at 1kHz VIN = 2.5Vp-p at 10kHz 0.5 DCLK Static POWER-SUPPLY REQUIREMENTS +VCC Quiescent Current ✻ 40 3 | IIH | ≤ +5µA | IIL | ≤ +5µA IOH = –250µA IOL = 250µA +VCC • 0.7 –0.3 +VCC • 0.8 Specified Performance 2.7 ✻ ✻ ✻ 3.2 –40 ✻ ✻ ✻ ✻ ✻ 0.4 Binary Two’s Complement Power Dissipation ✻ V GΩ µA µA µA ✻ 5.5 +0.8 1.2 105 dB dB dB dB ✻ ✻ ✻ ✻ ✻ CMOS fSAMPLE = 10kHz Power-Down Mode(3, 4), CS = +VCC TEMPERATURE RANGE Specified Performance +VCC/2 5 13 2.5 0.001 fSAMPLE = 12.5kHz DCLK Static DIGITAL INPUT/OUTPUT Logic Family Logic Levels VIH VIL VOH VOL Data Format ✻ ✻ ✻ ✻ –94 81 98 100 3.6 1.85 ✻ ✻ 3 5 +85 ✻ ✻ ✻ V V V V ✻ ✻ V mA µA µA mW ✻ °C ✻ Same specifications as ADS8343E. NOTES: (1) LSB means Least Significant Bit. With VREF equal to +1.25V, one LSB is 38µV. (2) First nine harmonics of the test frequency. (3) Auto power-down mode (PD1 = PD0 = 0) active or SHDN = GND. (4) Power-down after conversion mode with external clock gated ‘HIGH’. 4 ADS8343 www.ti.com SBAS183C TYPICAL CHARACTERISTICS: +5V At TA = +25°C, +VCC = +5V, VREF = +2.5V, fSAMPLE = 100kHz, and fCLK = 24 • fSAMPLE = 2.4MHz, unless otherwise noted. FREQUENCY SPECTRUM (4096 Point FFT; fIN = 9.985kHz, –0.2dB) 0 0 –20 –20 –40 –40 Amplitude (dB) Amplitude (dB) FREQUENCY SPECTRUM (4096 Point FFT; fIN = 1.001kHz, –0.2dB) –60 –80 –100 –60 –80 –100 –120 –120 –140 –140 0 10 20 30 40 50 0 10 20 30 40 Frequency (kHz) Frequency (kHz) SIGNAL-TO-NOISE RATIO AND SIGNAL-TO-(NOISE + DISTORTION) vs INPUT FREQUENCY SPURIOUS-FREE DYNAMIC RANGE AND TOTAL HARMONIC DISTORTION vs INPUT FREQUENCY 100 50 110 –110 80 100 –100 90 –90 THD(1) 80 –80 SINAD 70 70 60 –70 NOTE: (1) First nine harmonics of the input frequency. 60 1 10 100 1 10 Frequency (kHz) Frequency (kHz) EFFECTIVE NUMBER OF BITS vs INPUT FREQUENCY CHANGE IN SIGNAL-TO-(NOISE + DISTORTION) vs TEMPERATURE 0.1 15.0 fIN = 4.956kHz, –0.2dB Delta from 25°C (dB) 14.5 Effective Number of Bits –60 100 14.0 13.5 13.0 12.5 0 –0.1 –0.2 12.0 11.5 –0.3 11.0 1 10 100 Frequency (kHz) –25 0 25 50 75 100 Temperature (°C) ADS8343 SBAS183C –50 www.ti.com 5 THD (dB) SFDR (dB) SNR and SINAD (dB) SFDR SNR 90 TYPICAL CHARACTERISTICS: +5V (Cont.) At TA = +25°C, +VCC = +5V, VREF = +2.5V, fSAMPLE = 100kHz, and fCLK = 24 • fSAMPLE = 2.4MHz, unless otherwise noted. DIFFERENTIAL LINEARITY ERROR vs CODE 4 2 3 1 2 DLE (LSBs) ILE (LSBs) INTEGRAL LINEARITY ERROR vs CODE 3 0 –1 1 0 –2 –1 –3 –2 –4 8000H 0000H C000H 4000H –3 8000H 7FFFH 0000H C000H Output Code SUPPLY CURRENT vs TEMPERATURE Delta from 25°C (LSBs) Supply Current (mA) 1 1.5 1.4 1.3 1.2 0 –1 –2 –3 –4 –50 –25 0 25 50 75 100 –50 –25 0 25 50 75 Temperature (°C) Temperature (°C) CHANGE IN GAIN vs TEMPERATURE WORST-CASE CHANNEL-TO-CHANNEL BPZ MATCH vs TEMPERATURE 100 4.5 BPZ Match (LSBs) 1.0 Delta from 25°C (LSBs) 7FFFH CHANGE IN BPZ vs TEMPERATURE 1.6 0.5 0 –0.5 4.0 3.5 3.0 –50 –25 0 25 50 75 –50 100 –25 0 25 50 75 100 Temperature (°C) Temperature (°C) 6 4000H Output Code ADS8343 www.ti.com SBAS183C TYPICAL CHARACTERISTICS: +5V (Cont.) At TA = +25°C, +VCC = +5V, VREF = +2.5V, fSAMPLE = 100kHz, and fCLK = 24 • fSAMPLE = 2.4MHz, unless otherwise noted. COMMON-MODE REJECTION vs FREQUENCY 0.4 100 0.3 90 CMRR (dB) Gain Match (LSBs) WORST CASE CHANNEL-TO-CHANNEL GAIN MATCH vs TEMPERATURE 0.2 0.1 80 70 0 60 VCM = 2Vp-p Sinewave Centered Around VREF –0.1 50 –50 –25 0 25 50 75 100 0.1 1 Temperature (°C) 10 100 Frequency (kHz) TYPICAL CHARACTERISTICS: +2.7V At TA = +25°C, +VCC = +2.7V, VREF = +1.25V, fSAMPLE = 100kHz, and fCLK = 24 • fSAMPLE = 2.4MHz, unless otherwise noted. FREQUENCY SPECTRUM (4096 Point FFT; fIN = 9.985kHz, –0.2dB) 0 0 –20 –20 –40 –40 Amplitude (dB) –60 –80 –100 –120 –80 –100 –120 –140 –140 0 10 20 30 40 50 0 10 20 30 40 Frequency (kHz) Frequency (kHz) SIGNAL-TO-NOISE RATIO AND SIGNAL-TO-(NOISE + DISTORTION) vs INPUT FREQUENCY SPURIOUS-FREE DYNAMIC RANGE AND TOTAL HARMONIC DISTORTION vs INPUT FREQUENCY 95 100 50 –100 90 SNR 85 –90 SFDR SFDR (dB) SNR and SINAD (dB) –60 75 SINAD 80 –80 70 THD(1) –70 65 60 –60 NOTE: (1) First nine harmonics of the input frequency. 55 500 1 10 100 Frequency (kHz) 10 100 Frequency (kHz) ADS8343 SBAS183C –50 1 www.ti.com 7 THD (dB) Amplitude (dB) FREQUENCY SPECTRUM (4096 Point FFT; fIN = 1.001kHz, –0.2dB) TYPICAL CHARACTERISTICS: +2.7V (Cont.) At TA = +25°C, +VCC = +2.7V, VREF = +1.25V, fSAMPLE = 100kHz, and fCLK = 24 • fSAMPLE = 2.4MHz, unless otherwise noted. EFFECTIVE NUMBER OF BITS vs INPUT FREQUENCY CHANGE IN SIGNAL-TO-(NOISE + DISTORTION) vs TEMPERATURE 0.4 14.0 fIN = 4.956kHz, –0.2dB 0.2 13.0 Delta from 25°C (dB) Effective Number of Bits 13.5 12.5 12.0 11.5 11.0 10.5 10.0 0 –0.2 –0.4 –0.6 9.5 –0.8 9.0 1 10 –50 100 –25 0 Frequency (kHz) 4 2 3 DLE (LSBs) ILE (LSBs) 3 1 0 –1 75 100 2 1 0 –1 –2 –2 –3 8000H 0000H C000H 4000H –3 8000H 7FFFH 0000H C000H Output Code 4000H 7FFFH Output Code SUPPLY CURRENT vs TEMPERATURE CHANGE IN BPZ vs TEMPERATURE 1.0 Delta from 25°C (LSBs) 1.2 Supply Current (mA) 50 DIFFERENTIAL LINEARITY ERROR vs CODE INTEGRAL LINEARITY ERROR vs CODE 1.1 1.0 0.9 0.5 0 –0.5 –1.0 –50 –25 0 25 50 75 100 –50 Temperature (°C) 8 25 Temperature (°C) –25 0 25 50 75 100 Temperature (°C) ADS8343 www.ti.com SBAS183C TYPICAL CHARACTERISTICS: +2.7V (Cont.) At TA = +25°C, +VCC = +2.7V, VREF = +1.25V, fSAMPLE = 100kHz, and fCLK = 24 • fSAMPLE = 2.4MHz, unless otherwise noted. WORST-CASE CHANNEL-TO-CHANNEL BPZ MATCH vs TEMPERATURE CHANGE IN GAIN vs TEMPERATURE 1.5 BPZ Match (LSBs) Delta from 25°C (LSBs) 0.5 0 –0.5 –1.0 1.0 0.5 0 –50 –25 0 25 50 75 –50 100 –25 0 50 75 100 COMMON-MODE REJECTION vs FREQUENCY 0.16 80 0.15 70 CMRR (dB) Gain Match (LSBs) WORST-CASE CHANNEL-TO-CHANNEL GAIN MATCH vs TEMPERATURE 0.14 0.13 60 50 VCM = 1Vp-p Sinewave Centered Around VREF 0.12 –50 –25 0 25 50 75 40 100 0.1 Temperature (°C) 1 10 100 Frequency (kHz) POWER-DOWN SUPPLY CURRENT vs TEMPERATURE SUPPLY CURRENT vs +VSS 140 1.4 External Clock Disabled fSAMPLE = 100kHz Supply Current (mA) 120 Supply Current (mA) 25 Temperature (°C) Temperature (°C) 100 80 60 40 1.3 1.2 1.1 20 0 1.0 –50 –25 0 25 50 75 100 2.5 Temperature (°C) 3.5 4.0 4.5 5.0 +VSS (V) ADS8343 SBAS183C 3.0 www.ti.com 9 TYPICAL CHARACTERISTICS: +2.7V (Cont.) At TA = +25°C, +VCC = +2.7V, VREF = +1.25V, fSAMPLE = 100kHz, and fCLK = 24 • fSAMPLE = 2.4MHz, unless otherwise noted. SUPPLY CURRENT vs SAMPLING FREQUENCY 1.4 fCLK = 2.4MHz Supply Current (mA) 1.2 1.0 VSS = 5.0V 0.8 0.6 VSS = 2.7V 0.4 0.2 Power-Down After Conversion Mode. External Clock Gated HIGH After Conversion. 0 10 20 30 40 50 60 70 80 90 100 Sampling Frequency (kHz) THEORY OF OPERATION The ADS8343 is a classic Successive Approximation Register (SAR) A/D converter. The architecture is based on capacitive redistribution which inherently includes a sample-and-hold function. The converter is fabricated on a 0.6µm CMOS process. The basic operation of the ADS8343 is shown in Figure 1. The device requires an external reference and an external clock. It operates from a single supply of 2.7V to 5.25V. The external reference can be any voltage between 500mV and +VCC/2. The value of the reference voltage directly sets the input range of the converter. The average reference input current depends on the conversion rate of the ADS8343. The analog input to the converter is differential and is provided via a 4-channel multiplexer. The input can be provided in reference to a voltage on the COM pin (which is generally VREF) or differentially by using two of the four input channels (CH0-CH3). The particular configuration is selectable via the digital interface. ANALOG INPUT The analog input is bipolar and fully differential. There are two general methods of driving the analog input of the ADS8343: single-ended or differential, as shown in Figure 2. ADS8343 + 1µF to 10µF CHX ADS8343 ±VREF(1) +2.7V to +5V COM 0.1µF 1 +VCC DCLK 16 2 CH0 CS 15 3 CH1 DIN 14 4 CH2 BUSY 13 5 CH3 DOUT 12 6 COM GND 11 7 SHDN GND 10 8 VREF +VCC Common-Mode Voltage (typically VREF) Serial/Conversion Clock Chip Select Single-Ended Input Single-ended or differential analog inputs. VREF Serial Data In ± Serial Data Out Common-Mode Voltage 1µF 10 2 (1) ± VREF 2 CHX+ ADS8343 CHX– Differential Input 9 FIGURE 1. Basic Operation of the ADS8343. VREF(1) NOTE: (1) Relative to common-mode voltage. FIGURE 2. Methods of Driving the ADS8343—Single-Ended or Differential. ADS8343 www.ti.com SBAS183C When the input is single-ended, the COM input is held at a fixed voltage. The CHX input swings around the same voltage and the peak-to-peak amplitude is 2 • VREF. The value of VREF determines the range over which the common voltage may vary, as shown in Figure 3. 5 VCC = 5V 4.9 The input current on the analog inputs depends on a number of factors: sample rate, input voltage, and source impedance. Essentially, the current into the ADS8343 charges the internal capacitor array during the sample period. After this capacitance has been fully charged, there is no further input current. Common Voltage Range (V) 4 Single-Ended Input 3 2.8 2.1 2 In each case, care should be taken to ensure that the output impedance of the sources driving the CHX and COM inputs are matched. If this is not observed, the two inputs could have different settling times. This may result in offset error, gain error, and linearity error which change with both temperature and input voltage. If the impedance cannot be matched, the errors can be lessened by giving the ADS8343 additional acquisition time. Care must be taken regarding the absolute analog input voltage. Outside of these ranges, the converter’s linearity may not meet specifications. Please refer to the electrical characteristics table for min/max ratings. 1 0.1 0 REFERENCE INPUT –1 0.5 1.0 1.5 2.0 2.5 VREF (V) FIGURE 3. Single-Ended Input—Common Voltage Range vs VREF. When the input is differential, the amplitude of the input is the difference between the CHX and COM input. A voltage or signal is common to both of these inputs. The peak-to-peak amplitude of each input is VREF about this common voltage. However, since the inputs are 180° out-of-phase, the peakto-peak amplitude of the difference voltage is 2 • VREF. The value of VREF also determines the range of the voltage that may be common to both inputs, as shown in Figure 4. The external reference sets the analog input range. The ADS8343 will operate with a reference in the range of 500mV to +VCC/2. Keep in mind that the analog input is the difference between the CHX input and the COM input, as shown in Figure 5. For example, in the single-ended mode, with VREF and COM pin set to 1.25V, the selected input channel (CH0-CH3) will properly digitize a signal in the range of 0V to 2.50V relative to GND. If the COM pin is connected to 2.0V, the input range on the selected channel is 0.75V to 3.25V. A2-A0 (Shown 001B) CH0 CH1 CH2 +IN CH3 5.2 Converter 5 –IN VCC = 5V 4.2 Common Voltage Range (V) 4 3 COM Differential Input SGL/DIF (Shown HIGH) 2 FIGURE 5. Simplified Diagram of the Analog Input. 1 0.8 0.2 0 0.0 1.0 1.5 2.0 2.5 VREF (V) FIGURE 4. Differential Input—Common Voltage Range vs VREF. There are several critical items concerning the reference input and its wide voltage range. As the reference voltage is reduced, the analog voltage weight of each digital output code is also reduced. This is often referred to as the LSB (Least Significant Bit) size and is equal to the reference voltage divided by 65,536. Any offset or gain error inherent in the A/D converter will appear to increase, in terms of LSB ADS8343 SBAS183C www.ti.com 11 size, as the reference voltage is reduced. For example, if the offset of a given converter is 2LSBs with a 2.5V reference, then it will typically be 10LSBs with a 0.5V reference. In each case, the actual offset of the device is the same, 76µV. converter enters the conversion mode. At this point, the input sample-and-hold goes into the hold mode. The next 16 clock cycles accomplish the actual A/D conversion. The noise or uncertainty of the digitized output will increase with lower LSB size. With a reference voltage of 500mV, the LSB size is 7.6µV. This level is below the internal noise of the device. As a result, the digital output code will not be stable and vary around a mean value by a number of LSBs. The distribution of output codes will be gaussian and the noise can be reduced by simply averaging consecutive conversion results or applying a digital filter. Also shown in Figure 6 is the placement and order of the control bits within the control byte. Tables I and II give detailed information about these bits. The first bit, the ‘S’ bit, must always be HIGH and indicates the start of the control byte. The ADS8343 will ignore inputs on the DIN pin until the start bit is detected. The next three bits (A2-A0) select the active input channel or channels of the input multiplexer, as shown in Tables III and IV and Figure 5. Control Byte With a lower reference voltage, care should be taken to provide a clean layout including adequate bypassing, a clean (low-noise, low-ripple) power supply, a low-noise reference, and a low-noise input signal. Because the LSB size is lower, the converter will also be more sensitive to nearby digital signals and electromagnetic interference. Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) S A2 A1 A0 — SGL/DIF PD1 PD0 TABLE I. Order of the Control Bits in the Control Byte. The voltage into the VREF input is not buffered and directly drives the Capacitor Digital-to-Analog Converter (CDAC) portion of the ADS8343. Typically, the input current is 13µA with a 2.5V reference. This value will vary by microamps depending on the result of the conversion. The reference current diminishes directly with both conversion rate and reference voltage. As the current from the reference is drawn on each bit decision, clocking the converter more quickly during a given conversion period will not reduce overall current drain from the reference. BIT NAME DESCRIPTION 7 S Start Bit. Control byte starts with first HIGH bit on DIN. 6-4 A2-A0 Channel Select Bits. Along with the SGL/DIF bit, these bits control the setting of the multiplexer input. 2 SGL/DIF Single-Ended/Differential Select Bit. Along with bits A2-A0, this bit controls the setting of the multiplexer input. 1-0 PD1-PD0 Power-Down Mode Select Bits. See Table V for details. TABLE II. Descriptions of the Control Bits within the Control Byte. DIGITAL INTERFACE Figure 6 shows the typical operation of the ADS8343’s digital interface. This diagram assumes that the source of the digital signals is a microcontroller or digital signal processor with a basic serial interface (note that the digital inputs are overvoltage tolerant up to 5.5V, regardless of +VCC). Each communication between the processor and the converter consists of eight clock cycles. One complete conversion can be accomplished with three serial communications, for a total of 24 clock cycles on the DCLK input. A2 A1 A0 CH0 0 0 1 +IN 1 0 1 0 1 0 1 1 0 CH1 CH2 CH3 COM –IN +IN –IN +IN –IN +IN –IN TABLE III. Single-Ended Channel Selection (SGL/DIF HIGH). The first eight cycles are used to provide the control byte via the DIN pin. When the converter has enough information about the following conversion to set the input multiplexer appropriately, it enters the acquisition (sample) mode. After three more clock cycles, the control byte is complete and the A2 A1 A0 CH0 CH1 0 0 1 +IN –IN CH2 CH3 1 0 1 –IN +IN 0 1 0 +IN –IN 1 1 0 –IN +IN COM TABLE IV. Differential Channel Control (SGL/DIF LOW). CS tACQ DCLK 1 8 Idle DIN S A2 8 1 Acquire A1 A0 1 8 1 8 Conversion Idle SGL/ PD1 PD0 DIF S (START) A2 Acquire A1 A0 1 Conversion SGL/ PD1 PD0 DIF (START) BUSY DOUT 15 14 13 12 11 10 9 8 7 (MSB) 6 5 4 3 2 1 0 (LSB) Zero Filled... 15 14 (MSB) FIGURE 6. Conversion Timing, 24-Clocks per Conversion, 8-Bit Bus Interface. No DCLK delay required with dedicated serial port. 12 ADS8343 www.ti.com SBAS183C The SGL/DIF bit controls the multiplexer input mode: either single-ended (HIGH) or differential (LOW). In single-ended mode, the selected input channel is referenced to the COM pin. In differential mode, the two selected inputs provide a differential input. See Tables III and IV and Figure 5 for more information. The last two bits (PD1-PD0) select the powerdown mode as shown in Table V. If both inputs are HIGH, the device is always powered up. If both inputs are LOW, the device enters a power-down mode between conversions. When a new conversion is initiated, the device will resume normal operation instantly—no delay is needed to allow the device to power up and the very first conversion will be valid. PD1 PD0 0 0 1 0 1 0 1 1 DESCRIPTION Power-down between conversions. When each conversion is finished, the converter enters a lowpower mode. At the start of the next conversion, the device instantly powers up to full power. There is no need for additional delays to assure full operation and the very first conversion is valid. Selects internal clock mode. Reserved for future use. No power-down between conversions, device always powered. Selects external clock mode. TABLE V. Power-Down Selection. Clock Modes The ADS8343 can be used with an external serial clock or an internal clock to perform the successive-approximation conversion. In both clock modes, the external clock shifts data in and out of the device. Internal clock mode is selected when PD1 is HIGH and PD0 is LOW. If the user decides to switch from one clock mode to the other, an extra conversion cycle will be required before the ADS8343 can switch to the new mode. The extra cycle is required because the PD0 and PD1 control bits need to be written to the ADS8343 prior to the change in clock modes. When power is first applied to the ADS8343, the user must set the desired clock mode. It can be set by writing PD1 = 1 and PD0 = 0 for internal clock mode or PD1 = 1 and PD0 = 1 for external clock mode. After enabling the required clock mode, only then should the ADS8343 be set to power-down between conversions (i.e., PD1 = PD0 = 0). The ADS8343 maintains the clock mode it was in prior to entering the power-down modes. External Clock Mode In external clock mode, the external clock not only shifts data in and out of the ADS8343, it also controls the A/D conversion steps. BUSY will go HIGH for one clock period after the last bit of the control byte is shifted in. Successive-approximation bit decisions are made and appear at DOUT on each of the next 16 DCLK falling edges, see Figure 6. Figure 7 shows the BUSY timing in external clock mode. Since one clock cycle of the serial clock is consumed with BUSY going HIGH (while the MSB decision is being made), 16 additional clocks must be given to clock out all 16 bits of data; thus, one conversion takes a minimum of 25 clock cycles to fully read the data. Since most microprocessors communicate in 8-bit transfers, this means that an additional transfer must be made to capture the LSB. There are two ways of handling this requirement. One is presented in Figure 6, where the beginning of the next control byte appears at the same time the LSB is being clocked out of the ADS8343. This method allows for maximum throughput and 24 clock cycles per conversion. CS tCSS tCL tCH tBD tBD tD0 tCSH DCLK tDS DIN tDH PD0 tBDV tBTR BUSY tDV tTR DOUT 15 14 FIGURE 7. Detailed Timing Diagram. ADS8343 SBAS183C www.ti.com 13 The other method is shown in Figure 8, which uses 32 clock cycles per conversion; the last seven clock cycles simply shift out zeros on the DOUT line. BUSY and DOUT go into a high-impedance state when CS goes HIGH; after the next CS falling edge, BUSY will go LOW. SYMBOL DESCRIPTION MIN tACQ Acquisition Time 1.5 TYP MAX UNITS tDS DIN Valid Prior to DCLK Rising 100 ns tDH DIN Hold After DCLK HIGH 10 ns µs tDO DCLK Falling to DOUT Valid 200 ns Internal Clock Mode tDV CS Falling to DOUT Enabled 200 ns tTR CS Rising to DOUT Disabled 200 ns In internal clock mode, the ADS8343 generates its own conversion clock internally. This relieves the microprocessor from having to generate the SAR conversion clock and allows the conversion result to be read back at the processor’s convenience, at any clock rate from 0MHz to 2.0MHz. BUSY goes LOW at the start of conversion and then returns HIGH when the conversion is complete. During the conversion, BUSY will remain LOW for a maximum of 8µs. Also, during the conversion, DCLK should remain LOW to achieve the best noise performance. The conversion result is stored in an internal register; the data may be clocked out of this register any time after the conversion is complete. tCSS CS Falling to First DCLK Rising 100 ns tCSH CS Rising to DCLK Ignored 0 ns tCH DCLK HIGH 200 ns tCL DCLK LOW 200 tBD DCLK Falling to BUSY Rising 200 ns tBDV CS Falling to BUSY Enabled 200 ns tBTR CS Rising to BUSY Disabled 200 ns ns TABLE VI. Timing Specifications (+VCC = +2.7V to 3.6V, TA = –40°C to +85°C, CLOAD = 50pF). SYMBOL If CS is LOW when BUSY goes LOW following a conversion, the next falling edge of the external serial clock will write out the MSB on the DOUT line. The remaining bits (D14-D0) will be clocked out on each successive clock cycle following the MSB. If CS is HIGH when BUSY goes LOW then the DOUT line will remain in tri-state until CS goes LOW, as shown in Figure 9. CS does not need to remain LOW once a conversion has started. Note that BUSY is not tri-stated when CS goes HIGH in internal clock mode. Data can be shifted in and out of the ADS8343 at clock rates exceeding 2.4MHz, provided that the minimum acquisition time tACQ, is kept above 1.7µs. DESCRIPTION MIN TYP MAX UNITS tACQ Acquisition Time 1.7 tDS DIN Valid Prior to DCLK Rising 50 ns tDH DIN Hold After DCLK HIGH 10 ns µs tDO DCLK Falling to DOUT Valid 100 ns tDV CS Falling to DOUT Enabled 70 ns tTR CS Rising to DOUT Disabled 70 ns tCSS CS Falling to First DCLK Rising 50 ns tCSH CS Rising to DCLK Ignored 0 ns tCH DCLK HIGH 150 ns tCL DCLK LOW 150 tBD DCLK Falling to BUSY Rising 100 ns tBDV CS Falling to BUSY Enabled 70 ns tBTR CS Rising to BUSY Disabled 70 ns ns TABLE VII. Timing Specifications (+VCC = +4.75V to +5.25V, TA = –40°C to +85°C, CLOAD = 50pF). Digital Timing Figure 4 and Tables VI and VII provide detailed timing for the digital interface of the ADS8343. CS tACQ DCLK 1 8 Idle DIN S A2 1 8 Acquire A1 A0 1 1 8 8 Conversion Idle SGL/ DIF PD1 PD0 (START) BUSY DOUT 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 (MSB) Zero Filled... 0 (LSB) FIGURE 8. External Clock Mode 32 Clocks Per Conversion. CS tACQ DCLK 1 8 Idle DIN S A2 Acquire A1 A0 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Conversion SGL/ DIF PD1 PD0 (START) BUSY DOUT 15 14 13 12 11 10 (MSB) 9 8 7 6 5 4 3 2 1 0 Zero Filled... (LSB) FIGURE 9. Internal Clock Mode Timing. 14 ADS8343 www.ti.com SBAS183C DATA FORMAT The output data from the ADS8343 is in Binary Two’s Complement format, as shown in Table VIII. This table represents the ideal output code for the given input voltage and does not include the effects of offset, gain, or noise. DIGITAL OUTPUT Full-Scale Range 2 • VREF Least Significant Bit (LSB) 2 • VREF/65536 BINARY CODE HEX CODE +Full-Scale +VREF – 1LSB 0111 1111 1111 1111 7FFF 0V 0000 0000 0000 0000 0000 0V – 1LSB 1111 1111 1111 1111 FFFF –VREF 1000 0000 0000 0000 8000 Midscale Midscale – 1LSB –Full-Scale BINARY TWO’S COMPLEMENT 1000 fCLK = 24 • fSAMPLE TABLE VIII. Ideal Input Voltages and Output Codes. POWER DISSIPATION There are three power modes for the ADS8343: full-power (PD1 = PD0 = 1B), auto power-down (PD1 = PD0 = 0B), and shutdown (SHDN LOW). The affects of these modes varies depending on how the ADS8343 is being operated. For example, at full conversion rate and 24-clocks per conversion, there is very little difference between full-power mode and auto power-down, a shutdown (SHDN LOW) will not lower power dissipation. When operating at full-speed and 24 clocks per conversion (see Figure 6), the ADS8343 spends most of its time acquiring or converting. There is little time for auto power-down, assuming that this mode is active. Thus, the difference between full-power mode and auto power-down is negligible. If the conversion rate is decreased by simply slowing the frequency of the DCLK input, the two modes remain approximately equal. However, if the DCLK frequency is kept at the maximum rate during a conversion, but conversion are simply done less often, then the difference between the two modes is dramatic. Figure 10 shows the difference between reducing the DCLK frequency (“scaling” DCLK to match the conversion rate) or maintaining DCLK at the highest frequency and reducing the number of conversion per second. In the later case, the converter spends an increasing percentage of its time in power-down mode (assuming the auto power-down mode is active). Supply Current (µA) ANALOG VALUE Operating the ADS8343 in auto power-down mode will result in the lowest power dissipation, and there is no conversion time “penalty” on power-up. The very first conversion will be valid. SHDN can be used to force an immediate power-down. 100 fCLK = 2.4MHz 10 TA = 25°C +VCC = +2.7V VREF = +2.5V PD1 = PD0 = 0 1 1k 10k 100k 1M fSAMPLE (Hz) FIGURE 10. Supply Current versus Directly Scaling the Frequency of DCLK with Sample Rate or Keeping DCLK at the Maximum Possible Frequency. 14 TA = 25°C +VCC = +2.7V VREF = +2.5V fCLK = 24 • fSAMPLE PD1 = PD0 = 0 12 Supply Current (µA) DESCRIPTION If DCLK is active and CS is LOW while the ADS8343 is in auto power-down mode, the device will continue to dissipate some power in the digital logic. The power can be reduced to a minimum by keeping CS HIGH. The differences in supply current for these two cases are shown in Figure 11. 10 8 6 CS LOW (GND) 4 2 CS HIGH (+VCC) 0 0.09 0.00 1k 10k 100k 1M fSAMPLE (Hz) FIGURE 11. Supply Current vs State of CS . ADS8343 SBAS183C www.ti.com 15 NOISE AVERAGING The noise floor of the ADS8343 itself is extremely low, as can be seen from Figures 12 and 13, and is much lower than competing A/D converters. The ADS8343 was tested at both 5V and 2.7V and in both the internal and external clock modes. A low-level DC input was applied to the analog input pins and the converter was put through 5000 conversions. The digital output of the A/D converter will vary in output code due to the internal noise of the ADS8343. This is true for all 16-bit, SAR-type, A/D converters. Using a histogram to plot the output codes, the distribution should appear bell-shaped with the peak of the bell curve representing the nominal code for the input value. The ±1σ, ±2σ, and ±3σ distributions will represent the 68.3%, 95.5%, and 99.7%, respectively, of all codes. The transition noise can be calculated by dividing the number of codes measured by 6 and this will yield the ±3σ distribution or 99.7% of all codes. Statistically, up to 3 codes could fall outside the distribution when executing 1000 conversions. The ADS8343, with < 3 output codes for the ±3σ distribution, will yield a < ±0.5LSB transition noise at 5V operation. Remember, to achieve this low noise performance, the peak-to-peak noise of the input signal and reference must be < 50µV. The noise of the A/D converter can be compensated by averaging the digital codes. By averaging conversion results, transition noise will be reduced by a factor of 1/√n, where n is the number of averages. For example, averaging 4 conversion results will reduce the transition noise by 1/2 to ±0.25LSBs. Averaging should only be used for input signals with frequencies near DC. 3295 774 131 FFFEH FFFFH 0000H 0001H 0002H Code FIGURE 12. Histogram of 5000 Conversions of a DC Input at the Code Transition, 5V Operation External Clock Mode. 2387 905 8 512 38 38 7 FFFCH FFFDH FFFEH FFFFH 0000H 0001H 0002H 0003H 0004H Code FIGURE 13. Histogram of 5000 Conversions of a DC Input at the Code Center, 2.7V Operation Internal Clock Mode. 16 For optimum performance, care should be taken with the physical layout of the ADS8343 circuitry. This is particularly true if the reference voltage is low and/or the conversion rate is high. The basic SAR architecture is sensitive to glitches or sudden changes on the power supply, reference, ground connections, and digital inputs that occur just prior to latching the output of the analog comparator. Thus, during any single conversion for an nbit SAR converter, there are n “windows” in which large external transient voltages can easily affect the conversion result. Such glitches might originate from switching power supplies, nearby digital logic, and high-power devices. The degree of error in the digital output depends on the reference voltage, layout, and the exact timing of the external event. The error can change if the external event changes in time with respect to the DCLK input. The reference should be similarly bypassed with a 1µF capacitor. Again, a series resistor and large capacitor can be used to low-pass filter the reference voltage. If the reference voltage originates from an op amp, make sure that it can drive the bypass capacitor without oscillation (the series resistor can help in this case). The ADS8343 draws very little current from the reference on average, but it does place larger demands on the reference circuitry over short periods of time (on each rising edge of DCLK during a conversion). The ADS8343 architecture offers no inherent rejection of noise or voltage variation in regards to the reference input. This is of particular concern when the reference input is tied to the power supply. Any noise and ripple from the supply will appear directly in the digital results. While high-frequency noise can be filtered out as discussed in the previous paragraph, voltage variation due to line frequency (50Hz or 60Hz) can be difficult to remove. 694 411 LAYOUT With this in mind, power to the ADS8343 should be clean and well bypassed. A 0.1µF ceramic bypass capacitor should be placed as close to the device as possible. In addition, a 1µF to 10µF capacitor and a 5Ω or 10Ω series resistor may be used to low-pass filter a noisy supply. 705 95 For AC signals, a digital filter can be used to low-pass filter and decimate the output codes. This works in a similar manner to averaging; for every decimation by 2, the signalto-noise ratio will improve 3dB. The GND pin should be connected to a clean ground point. In many cases, this will be the “analog” ground. Avoid connections which are too near the grounding point of a microcontroller or digital signal processor. If needed, run a ground trace directly from the converter to the power-supply entry point. The ideal layout will include an analog ground plane dedicated to the converter and associated analog circuitry. ADS8343 www.ti.com SBAS183C PACKAGE OPTION ADDENDUM www.ti.com 11-Apr-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (°C) Top-Side Markings (3) (4) ADS8343E ACTIVE SSOP DBQ 16 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 ADS 8343E ADS8343E/2K5 ACTIVE SSOP DBQ 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 ADS 8343E ADS8343E/2K5G4 ACTIVE SSOP DBQ 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 ADS 8343E ADS8343EB ACTIVE SSOP DBQ 16 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 ADS 8343E B ADS8343EBG4 ACTIVE SSOP DBQ 16 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 ADS 8343E B ADS8343EG4 ACTIVE SSOP DBQ 16 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 ADS 8343E (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Top-Side Marking for that device. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 11-Apr-2013 Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 16-Aug-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device ADS8343E/2K5 Package Package Pins Type Drawing SSOP DBQ 16 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 2500 330.0 12.4 Pack Materials-Page 1 6.4 B0 (mm) K0 (mm) P1 (mm) 5.2 2.1 8.0 W Pin1 (mm) Quadrant 12.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 16-Aug-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) ADS8343E/2K5 SSOP DBQ 16 2500 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2014, Texas Instruments Incorporated