EGP30A THRU EGP30K 3.0 AMPS. Glass Passivated High Efficient Plastic Rectifiers Voltage Range 50 to 800 Volts Current 3.0 Amperes DO-201 Features Plastic material used carries Underwriters Laboratories Classification 94V-O Glass passivated cavity-free junction Superfast recovery time for high efficiency Low forward voltage, high current capability Low leakage current High surge current capability High temperature metallurgically bonded construction High temperature soldering guaranteed: 300℃ / 10seconds, .375”(9.5mm) lead length at 5 lbs., (2.3kg) tension Mechanical Data Case: JEDEC DO-201 molded plastic over solid glass body Lead: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting position: Any Weight: 0.048 ounce, 1.28 gram Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol EGP EGP Type Number 30A 30B Maximum Recurrent Peak Reverse Voltage VRRM 50 100 Maximum RMS Voltage VRMS 35 70 Maximum DC Blocking Voltage VDC 50 100 Maximum Average Forward Rectified Current 0.375”(9.5mm) Lead Length @ TA = 55℃ Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 3.0A Maximum DC Reverse Current @ TA=25℃ at Rated DC Blocking Voltage @ TA=125℃ Maximum Reverse Recovery Time ( Note 1 ) o TA=25 C Typical Junction Capacitance ( Note 2 ) Typical Thermal Resistance (Note 3) EGP EGP EGP EGP EGP Units 30D 30F 30G 30J 30K 200 140 200 300 210 300 400 280 400 600 420 600 800 560 800 V V V I(AV) 3.0 A IFSM 125 A 0.95 VF 1.25 1.7 5.0 100 IR uA uA 50 Trr Cj RθJA 60 TJ TSTG Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1.0 MHz and Applied Reverse Voltage of 4.0V D.C. 3. Mount on Cu-Pad Size 16mm x 16mm on P.C.B. Operating and Storage Temperature Range - 590 - 75 50 40 -65 to + 150 V nS pF ℃/W ℃ RATINGS AND CHARACTERISTIC CURVES (EGP30A THRU EGP30K) FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 10W NONINDUCTIVE 50W NONINDUCTIVE trr +0.5A (-) DUT PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) (+) -1.0A 1cm 100 RESISTIVE OR INDUCTIVE LOAD 0.375" (9.5mm) LEAD LENGTH 2.0 1.0 0 0 25 50 75 100 125 150 175 o PEAK FORWARD SURGE CURRENT. (A) AMBIENT TEMPERATURE. ( C) FIG.3- MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT Tj=125 0C 1 0.1 Tj=75 0C 0.01 Tj=25 0C Tj=Tj max. 8.3ms Single Half Sine Wave JEDEC Method 125 0.001 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 100 FIG.6- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 75 50 50 PULSE WIDTH-300 S 1% DUTY CYCLE 25 0 1 100 10 NUMBER OF CYCLES AT 60Hz FIG.4- TYPICAL JUNCTION CAPACITANCE 210 JUNCTION CAPACITANCE.(pF) Tj=150 0C 10 175 150 SET TIME BASE FOR 5/ 10ns/ cm FIG.5- TYPICAL REVERSE CHARACTERISTICS FIG.2- MAXIMUM FORWARD CURRENT DERATING CURVE Tj=25 0C f=1.0MHz Vsig=50mVp-p 180 150 120 90 INSTANTANEOUS FORWARD CURRENT. (A) AVERAGE FORWARD CURRENT. (A) NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms 3.0 0 -0.25A INSTANTANEOUS REVERSE CURRENT. ( A) (+) 50Vdc (approx) (-) 10 Tj=150 0C 1 Tj=25 0C 0.1 60 30 0 0.1 EGP30A-EGP30D EGP30F EGP30K EGP30A-EGP30D EGP30F-EGP30K 1 0.01 0.2 10 100 1000 REVERSE VOLTAGE. (V) - 591 - 0.4 0.6 0.8 1.0 1.2 1.4 FORWARD VOLTAGE. (V) 1.6 1.8