MIL-PRF-38534 AND 38535 CERTIFIED FACILITY 100 VOLT 20 AMP H-BRIDGE PWM MOTOR DRIVER/AMPLIFIER 4206 FEATURES: • • • • • • • Replaces APEX SA01 PWM Amplifier 100 Volt, 20 Amp Capability Self-Contained Smart Lowside/Highside Drive Circuitry Internal PWM Generation, Shoot-through Protection Isolated Case Allows Direct Heatsinking Available Fully Screened To MIL-PRF-38534 Class H Contact MSK for MIL-PRF-38534 Qualification Status DESCRIPTION: The MSK4206 is a complete H-Bridge microcircuit intended for use in DC brushed motor control applications or Class D switchmode amplification in severe operating conditions. All of the control circuitry, including an error amplifier, is internal to the device. A precision reference output is provided for use in offsetting the error amplifier. Fixed highside current limit is provided internally. Lowside current limit is user controlled with the use of an external resistor network. The design is packaged in a 10 pin bolt down power package. EQUIVALENT SCHEMATIC TYPICAL APPLICATIONS PIN-OUT INFORMATION • MOTOR CONTROL • REACTIVE LOADS • PIEZO ELEMENTS 1 2 3 4 5 1 - IN +IN EA OUT GND REF 6 7 8 9 10 A OUT +VS ISENSE B OUT SHDN/FILTER 8548-139 Rev. D 05/17 ABSOLUTE MAXIMUM RATINGS +VS IOUT IPK VOUT VIN VL 8 High Voltage Supply...................................................100V Continuous Output Current..........................................20A Peak Output Current....................................................30A Output Voltage Range..................................GND TO +VS Input Voltage, +IN and -IN ...............................0V TO 12V Logic Input Voltage (SHDN/FILTER)................0V TO 10V ELECTRICAL SPECIFICATIONS Parameter Test Conditions OUTPUT CHARACTERISTICS VDS(ON) Highside 6 ID = 10A VDS(ON) Lowside ID = 10A 6 VDS(ON) Highside 2 6 ID = 20A ID = 15A ID = 20A VDS(ON) Lowside 6 ID = 20A 2 RDS(ON) each MOSFET ID = 10A 2 6 7 P-CHANNEL N-CHANNEL Leakage Current Highside +VS = 80V Leakage Current Lowside A/B out = 80V OUTPUT FREQUENCY and DUTY CYCLE Switching Frequency EA OUT = 5V Duty Cycle EA OUT = 8V, Output A = 100%, Output B = 0% EA OUT = 2V, Output A = 0%, Output B = 100% SUPPLY CURRENT CHARACTERISTICS +VS 2 +VS Current IREF = 5mA, RL = 10KΩ SHDN/FILTER = <180mV +VS Current IREF = 5mA, RL = 10KΩ SHDN/FILTER = <180mV REFERENCE Output Voltage IOUT = 5mA Load Regulation Line Regulation Error Amp Offset Voltage Input Bias Current Offset Current Common Mode Voltage range 2 Common Mode Rejection, DC Slew Rate Open loop gain 2 Gain Bandwidth Product SHDN/FILTER Trip Point Input Current 2 9 TST Storage Temperature Range....................-65°C to +150°C TLD Lead Temperature Range (10 Seconds)............................................................300°C TC Case Operating Temperature Range MSK4206H..............................................-55°C to +125°C MSK4206...................................................-40°C to +85°C TJ Junction Temperature............................................+150°C θJc Thermal Resistance (Output FETS @ 125°C)...................................1.25°C/W (Output FETS @ 25°C).....................................1.0°C/W Group A Subgroup Min. 1 2 3 1 2 3 1 2 3 1 2 3 1 2 1 2 1 2 1 2 - 1.60 2.4 1.1 0.75 1.1 0.45 3.5 3.7 2.1 1.5 2.4 0.90 110 168 22 78 0.02 1.0 0.02 1.0 2.0 3.0 1.5 1.0 1.5 0.70 125 250 52 95 25 250 25 250 - 1.60 0.75 3.5 1.5 110 22 0.02 0.02 - 2.2 1.2 125 52 25 25 - V V V V V V V V V V V V mΩ mΩ mΩ mΩ µA µA µA µA 4 4 7 7 35 40 - 42 50 Verify Verify 49 60 - 32 40 - 42 50 Verify Verify 52 60 - KHz % P/F P/F 1, 2, 3 1 1 16 - 50 60 20 100 93 25 16 - 50 60 - 100 93 25 V mA mA 1 2, 3 - 7.46 7.42 - 7.50 20 1 7.54 7.58 - 7.42 - 7.50 20 1 7.58 - V V PPM/mA PPM/V 1 2, 3 1 2, 3 1 2, 3 1, 2, 3 -10 -15 2 0.5 0.7 0.01 0.01 - +10 +15 5 13 1 8 8 -15 2 0.5 0.01 0.01 +15 8 2 8 mV mV µA µA µA µA V 1, 2, 3 4, 5, 6 - 75 75 - 15 2 - 75 75 - 15 - - dB V/µS dB MHz 1 1 180 - 200 0.8 220 10 170 - 200 0.8 230 10 mV µA MSK4206H Typ. Max. Min. MSK4206 Typ. Max. Units NOTES: 1 +VS = 28V, I SENSE = Ground, SHDN/FILTER = 0V unless otherwise specified. 2 Guaranteed by design but not tested. Typical parameters are representative of actual device performance but are for reference only. 3 Class H devices are 100% tested to subgroups 1, 2, 3, 4 and 7. Subgroup 5 and 6 testing available upon request. 4 Subgroup 1, 4, 7 TA = +25°C 2, 5 TA = +125°C 3, 6 TA = -55°C 5 Industrial grade devices shall be 100% tested at 25°C only. 6 Tested with a low duty cycle pulse to minimize junction heating. 7 The typical internal reading is for the die only. This should be used for thermal calculations only. 8 Continuous operation at or above absolute maximum ratings may adversly effect the device performance and/or life cycle. 9 Internal solder reflow temperature is 180°C, do not exceed. 2 8548-139 Rev. D 05/17 APPLICATION NOTES MSK4206 PIN DESCRIPTION +VS - Is the voltage supply for powering internal logic and drivers as well as H-bridge supply pin. The MOSFETS obtain the drive current from this supply pin. The MOSFETs are rated at 100 volts. Proper bypassing to GND with sufficient capacitance to suppress any voltage transients, and ensure removal of any drooping during switching, should be done as close to the pin on the hybrid as possible. AOUT - Is the output pin for one half of the bridge. As EA OUT goes more positive the duty cycles increases at this output. BOUT - Is the output pin for one half of the bridge. As EA OUT goes more positive the duty cycles decreases at this output. ISENSE - Is the connection for the bottom of the half bridge. This can have a sense resistor connection to the +Vs return ground for current limit sensing, or can be connected directly to ground. The maximum voltage on this pin is ±5V with respect to GND. GND - Is the return connection for +VS. +IN - Is the non-inverting input to the internal error amplifier. This pin requires a level between 2 and 8V for proper operation. -IN - Is the inverting input to the internal error amplifier. EA OUT - Is the output of the internal error amplifier. The error amplifier output is connected internally to the PWM. An error amp output voltage higher than 5V will produce greater than 50% duty cycle pulses out of A OUT. An error amp voltage lower than 5V will produce greater than 50% duty cycle pulses out of B OUT. REF - Is the output of the internal precision reference. The internal reference will provide 7.5V with load current up to 5mA. SHDN/FILTER - Is the connection for disabling all 4 output switches. SHUTDOWN high overrides all other inputs. When taken low, everything functions normally. This pin should be grounded if not used. 3 8548-139 Rev. D 05/17 APPLICATION NOTES CONT'D CURRENT LIMIT The current limit function sets the peak limit on current flow in pin 8. This circuit can trip at anytime during the conduction period and will hold the output transistors off for the remainder of that conduction period. It is recommended that RLIMIT resistor be non-inductive. Load current flows in the ISENSE pin. To avoid errors due to lead length connect the SHDN/FILTER pin directly to the RLIMIT resistor (through the filter network and shutdown divider resistor) and connect the RLIMIT resistor directly to the +VS return. Switching noise spikes will invariably be found at the ISENSE pin. The noise spikes could trip the current limit threshold which is only 200mV. RFILTER and CFILTER should be adjusted so as to reduce the switching noise well below 200mV to prevent false current limiting. The sum of the DC level plus the noise peak will determine the current limiting value. As in most switching circuits it may be difficult to determine the true noise amplitude without careful attention to grounding of the oscilloscope probe. Use the shortest possible ground lead for the probe and connect exactly at the GND pin of the amplifier. Suggested starting values are CFILTER=0.01µF, RFILTER=5K. The required value of RLIMIT in voltage mode may be calculated by: RLIMIT=0.2V/ILIMIT where RLIMIT is the required resistor value and ILIMIT is the maximum desired current. If RSHDN is used it will further divide down the sense voltage. The shutdown divider network will also have an effect on the filtering circuit. FIGURE 1 ERROR AMPLIFIER The internal amplifier can be used to integrate the difference between command signals and feedback signals. For highest loop accurancy it is best to configure the error amplifier as an integrator. Poles and zeros must be selected to provide circuit stability while maximizing system respones. Specific component values will vary from system to system. The 7.5V reference output can be used to bias the non-inverting input of the error amplifier to the middle of its 2 to 8V common mode voltage range. (See typical application circuit). PROTECTION CIRCUITS In addition to the externally programmable current limit there is also a fixed internal current limit which senses only the highside current. The DC trip level is approximately 35A. Should either of the outputs be shorted to ground the highside current limit will latch off the output transistors. It will be necessary to remove the fault condition and recycle power to +VS to restart the circuit. 4 8548-139 Rev. D 05/17 TYPICAL APPLICATION CIRCUIT MOTOR DRIVER WITH TACH FEEDBACK MmkdkoadIT 5 8548-139 Rev. D 05/17 PERFORMANCE CURVES 6 8548-139 Rev. D 05/17 MECHANICAL SPECIFICATIONS WEIGHT= 35 GRAMS TYPICAL TORQUE SPEC: 8-10 IN-LBS ALL DIMENSIONS ARE SPECIFIED IN INCHES ORDERING INFORMATION MSK4206H SCREENING BLANK= INDUSTRIAL H=MIL-PRF-38534 CLASS H GENERAL PART NUMBER The above example is a Military grade class H hybrid. 7 8548-139 Rev. D 05/17 S N G I S E S I H E G D A K EW C PA R N E O T F E L T O O S N OB ON I S ER V T WEIGHT= 35 GRAMS TYPICAL TORQUE SPEC: 8-10 IN-LBS ALL DIMENSIONS ARE SPECIFIED IN INCHES 8 8548-139 Rev. D 05/17 REVISION HISTORY MSK www.anaren.com/MSK The information contained herein is believed to be accurate at the time of printing. MSK reserves the right to make changes to its products or specifications without notice, however, and assumes no liability for the use of its products. Please visit our website for the most recent revision of this datasheet. Contact MSK for MIL-PRF-38534 qualification status. 9 8548-139 Rev. D 05/17