Vertical Cavity Surface Emitting Laser in TO-46 Package OPV302 • • • • • 850nm VCSEL technology High thermal stability Low drive current High output power Narrow Beam Angle The OPV302 is a Vertical Cavity Surface Emitting Laser (VCSEL) packaged in a dome lens TO-46 package. VCSELs offer many advantages in sensing applications when compared to infrared LEDs. These devices require substantially lower drive currents to obtain the same amount of output power as LEDs. This feature allows VCSELs to be used in low power consumption applications such as battery operated equipment. The dome lens packaging creates a narrow beam angle from the device. Long distance applications may benefit from this feature as secondary optics may be eliminated, reducing total system cost. The OPV302 is optically and spectrally compatible with Optek’s standard detector products such as the OP800 series phototransistors, OP830 series photodarlingtons and the OP910 photodiode. Applications • • • • Emission Surface Non-contact position sensing Photoelectric sensors Optical encoders Light curtains OPV302 Pin Connection 1 VCSEL Anode 2 VCSEL Cathode 3 No Connection .186 .180 .210 .190 VCSEL .050 M AX .030 M AX 1 2 3X .500 M IN 3X .019 .016 2 Additional laser safety information can be found on the Optek website. See application bulletin #221. Classification is not marked on the device due to space limitations. See package outline for centerline of optical radiance. Operating devices beyond maximum rating may result in hazardous radiation exposure. 1 .230 .209 3 .100 Pb RoHS Optek reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc.— 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (800) 341-4747 FAX: (972) 323– 2396 [email protected] www.optekinc.com A subsidiary of TT electronics plc VCSEL in TO-46 Package OPV302 Absolute Maximum Ratings TA = 25o C unless otherwise noted Storage Temperature Range -40° to +100° C Operating Temperature Range -40° to +85° C 260° C(1) Lead Soldering Temperature [1/16 inch (1.6mm) from case for 5 sec with soldering iron] Maximum Forward Peak Current 20 mA Maximum Reverse Voltage 5V Electrical Characteristics (TA = 25°C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS POT Total Power Out mW IF = 7 mA ITH Threshold Current 3.0 mA Note 2 VF Forward Voltage 2.2 V IF = 7 mA IR Reverse Current 100 nA VR = 5 V RS Series Resistance 55 ohms Note 3 η Slope Efficiency 0.28 mW/mA Note 4 λ Wavelength 830 ∆λ Optical Bandwidth θ Beam Divergence 1.5 CONDITIONS 20 860 nm 0.85 nm 4 Degrees ∆η/∆T Temp Coefficient of Slope Efficiency -0.50 %/°C (0° - 70°C), Note 4 ∆λ/∆T Temp Coefficient of Wavelength 0.06 nm/°C (0° - 70°C) ∆lTH/∆T Temp Coefficient of Threshold Current ±1.0 mA ∆VF/∆T Temp Coefficient for Forward Voltage -2.5 mV/°C (0° - 70°C), Note 2 (0° - 70°C) NOTES: (1) RMA flux is recommended. Solder dwell time can be increased to 10 seconds when flow soldering. (2) Threshold Current is based on the two line intersection method specified in Telcordia GR-468-Core. Line 1 from 4 mA to 6 mA. Line 2 from 0 mA to 0.5 mA. (3) Series Resistance is the slope of the Voltage-Current line from 5 to 8 mA. (4) Slope efficiency, is the slope of the best fit LI line from 5 mA to 8 mA with 0.25mA test intervals. Normalized Output Power vs. Forward Current Typical Angular Output 100% 200% Normalized Output Power Relative Output 80% 60% 40% 20% 100% 0% -90 -60 -30 0 30 60 Normalized at 7mA, 25°C 90 Angular Displacement—Degrees OPTEK Technology Inc.— 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (800) 341-4747 FAX: (972) 323– 2396 [email protected] www.optekinc.com 0% 0 2 4 6 8 10 12 Forward Current—mA Issue 1.1 05.05 Page 2 of 2