Rohm DTC115GKA Digital transistors (built-in resistor) Datasheet

DTC115GUA / DTC115GKA / DTC115GSA
Transistors
Digital transistors (built-in resistor)
DTC115GUA / DTC115GKA / DTC115GSA
2.0
1.3
0.9
(1)
(2)
(3)
0.3
1.25
0~0.1
0.15
0.2
2.1
0.1Min.
Each lead has same dimensions
ROHM : UMT3
EIAJ : SC-70
C
(1) Emitter
(2) Base
(3) Collector
(1)
DTC115GKA
R
(2)
(3)
0.4
E
E : Emitter
C : Collector
B : Base
0.95 0.95
1.9
2.9
zEquivalent circuit
B
0.65 0.65
DTC115GUA
0.7
zExternal dimensions (Unit : mm)
zFeatures
1) The built-in bias resistors consist of thin-film resistors with
complete isolation to allow positive biasing of the input, and
parasitic effects are almost completely eliminated.
2) Only the on / off conditions need to be set for operation,
making device design easy.
3) Higher mounting densities can be achieved.
1.6
0~0.1
0.3Min.
zAbsolute maximum ratings (Ta=25°C)
Emitter-base voltage
Collector current
VEBO
IC
100
V
V
V
mA
200
mW
300
mW
150
°C
°C
Collector power
dissipation
DTA115GUA / DTA115GKA
50
5
Pc
DTA115GSA
Junction temperature
Tj
Tstg
Storage temperature
−55 to +150
DTC115GSA
4
zPackage, marking, and packaging specifications
Type
Package
Marking
Packaging code
Basic ordering unit (pieces)
DTC115GUA
UMT3
DTC115GKA
SMT3
K29
T106
K29
T146
3000
3000
(1) Emitter
(2) Base
(3) Collector
2
3Min.
Unit
50
3
Limits
VCBO
VCEO
Parameter
Each lead has same dimensions
ROHM : SMT3
EIAJ : SC-59
(15Min.)
Symbol
Collector-base voltage
Collector-emitter voltag
1.1
0.8
0.15
2.8
0.45
2.5
0.5 0.45
5
DTC115GSA
SPT
−
(1) (2) (3)
TP
5000
ROHM : SPT
EIAJ : SC-72
Taping specifications
(1) Emitter
(2) Collector
(3) Base
zElectrical characteristics (Ta=25°C)
Parameter
Collector-base breakdown voltage
Collector-emitter breakdown voltag
Emitter-base breakdown voltage
Collector cutoff current
Emitter cutoff current
Collector-emitter saturation voltage
DC current transfer ratio
Symbol
Min.
Typ.
Max.
Unit
BVCBO
BVCEO
50
50
5
−
−
−
−
0.5
V
V
V
µA
30
−
82
−
−
−
−
−
−
−
58
0.3
−
µA
V
−
70
−
100
250
130
−
kΩ
MHz
BVEBO
ICBO
IEBO
VCE(sat)
hFE
Emitter-base resistance
R
Transition frequency
fT
Conditions
IC=50µA
IC=1mA
IE=72µA
VCB=50V
VEB=4V
IC=5mA, IB=0.25mA
IC=5mA, VCE=5V
−
VCE=10V, IE=−5mA, f=100MHz
∗
∗ Transition frequency of the device.
Rev.A
1/2
DTC115GUA / DTC115GKA / DTC115GSA
Transistors
1k
OUTPUT CURRENT : lo
500
VCE=5V
Ta=100°C
200
Ta=25°C
100
Ta = −40°C
50
20
10
5
2
1
10µ
20µ
50µ 100µ 200µ 500µ 1m
2m
5m 10m
COLLECTOR CURRENT : IC (A)
Fig.1 DC current transfer ratio vs.
collector current characteristics
COLLECTOR SATURATION VOLTAGE : VCE(sat) (V)
zElectrical characteristics curves
1
500m
lC/lB=20/1
200m
Ta=100°C
Ta=25°C
100m
50m
Ta=−40°C
20m
10m
5m
2m
1m
10µ
20µ
50µ 100µ 200µ 500µ 1m
2m
5m 10m
COLLECTOR CURRENT : IC (A)
Fig.2 Collector-emitter saturation voltage vs.
collector current characteristics
Rev.A
2/2
Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level of
reliability and the malfunction of with would directly endanger human life (such as medical instruments,
transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other
safety devices), please be sure to consult with our sales representative in advance.
About Export Control Order in Japan
Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control
Order in Japan.
In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause)
on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction.
Appendix1-Rev1.1
Similar pages