NSC LM397MFX Single general purpose voltage comparator Datasheet

LM397
Single General Purpose Voltage Comparator
General Description
Features
The LM397 is a single voltage comparator with an input
common mode that includes ground. The LM397 is designed
to operate from a single 5V to 30V power supply or a split
power supply. Its low supply current is virtually independent
of the magnitude of the supply voltage.
The LM397 features an open collector output stage. This
allows the connection of an external resistor at the output.
The output can directly interface with TTL, CMOS and other
logic levels, by tying the resistor to different voltage levels
(level translator).
The LM397 is available in space saving SOT23-5 package
and pin compatible to TI’s TL331, single differential comparator.
(TA = 25˚C. Typical values unless otherwise specified).
n SOT23-5 package
n Industrial operating range
−40˚C to +85˚C
n Single or dual power supplies
n Wide supply voltage range
5V to 30V
n Low supply current
300µA
n Low input bias current
7nA
± 1nA
n Low input offset current
± 2mV
n Low input offset voltage
n Response time
440ns (50mV overdrive)
n Input common mode voltage
0 to VS - 1.5V
Applications
n
n
n
n
Connection Diagram
A/D converters
Pulse, square wave generators
Peak detector
Industrial applications
Typical Circuit
SOT23-5
20022108
Top View
20022109
FIGURE 1. Inverting Comparator with Hysteresis
Ordering Information
Package
Part Number
Package Marking
Transport Media
NSC Drawing
5-Pin SOT-23
LM397MF
C397
1k Units Tape and Reel
MF05A
LM397MFX
© 2001 National Semiconductor Corporation
DS200221
3k Units Tape and Reel
www.national.com
LM397 Single General Purpose Voltage Comparator
June 2001
LM397
Absolute Maximum Ratings
Junction Temperature (Note 4)
(Note 1)
+150˚C
Soldering Information
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Infrared or Convection (20 sec.)
235˚C
Wave Soldering (10 sec.)
260˚C
ESD Tolerance
Human Body Model
Machine Model
2KV (Note 2)
Operating Ratings (Note 1)
200V (Note 3)
VIN Differential
Supply Voltage, VS
30V
Supply Voltages
30V or ± 15V
Voltage at Input Pins
−0.3V to 30V
5V to 30V
Junction Temperature Range (Note 4)
−40˚C to +85˚C
Package Thermal Resistance (Note 4)
SOT23-5
168˚C/W
Storage Temperature Range
−65˚C to +150˚C
Electrical Characteristics
Unless otherwise specified, all limits guaranteed for at TJ = 25˚C, VS = 5V. Bold-
face limits apply at temperature extremes.
Symbol
Parameter
Conditions
Min
(Note 6)
Typ
(Note 5)
Max
(Note 6)
Units
VOS
Input Offset Voltage
VS = 5V to 30V,
VO = 1.4V, VCM = 0V
2
7
10
mV
IOS
Input Offset Current
VO = 1.4V, VCM = 0V
1.6
50
250
nA
IB
Input Bias Current
VO = 1.4V, VCM = 0V
10
250
400
nA
IS
Supply Current
RL = Open, VS = 5V
0.25
0.7
RL = Open, VS = 30V
0.30
2
mA
IO
Output Sink Current
VIN+ = 1V,VIN− = 0V, VO = 1.5V
ILEAKAGE
Output Leakage Current
VIN+ = 1V,VIN− = 0V, VO = 5V
0.1
nA
VIN+ = 1V,VIN− = 0V, VO = 30V
1
µA
180
VOL
Output Voltage Low
IO = −4mA, VIN+ = 0V,VIN− = 1V
VCM
Common-Mode Input Voltage
Range
VS = 5V to 30V (Note 7)
www.national.com
2
6
13
mA
400
700
VS - 1.5V
0
VS - 2V
0
mV
V
LM397
Electrical Characteristics
Unless otherwise specified, all limits guaranteed for at TJ = 25˚C, VS = 5V.
Boldface limits apply at temperature extremes. (Continued)
Symbol
Parameter
Conditions
Min
(Note 6)
Typ
(Note 5)
Max
(Note 6)
Units
AV
Voltage Gain
VS = 15V, VO = 1.4V to 11.4V,
RL > = 15kΩ connected to VS
120
tPHL
Propagation Delay (High to Low)
Input Overdrive = 5mV
RL = 5.1kΩ connected to 5V,
CL = 15pF
900
Input Overdrive = 50mV
RL = 5.1kΩ connected to 5V,
CL = 15pF
250
Input Overdrive = 5mV
RL = 5.1kΩ connected to 5V,
CL = 15pF
940
µs
Input Overdrive = 50mV
RL = 5.1kΩ connected to 5V,
CL = 15pF
440
ns
tPLH
Propagation Delay (Low to High)
V/mV
ns
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics.
Note 2: Human body model, 1.5kΩ in series with 100pF.
Note 3: Machine model, 0Ω in series with 200pF.
Note 4: The maximum power dissipation is a function of TJ(MAX), θJA , and TA. The maximum allowable power dissipation at any ambient temperature is
PD = (TJ(MAX) - TA)/ θJA . All numbers apply for packages soldered directly onto a PC board.
Note 5: Typical values represent the most likely parametric norm.
Note 6: All limits are guaranteed by testing or statistical analysis.
Note 7: The input common-mode voltage of either input should not be permitted to go below the negative rail by more than 0.3V. The upper end of the
common-mode voltage range is VS - 1.5V at 25˚C.
3
www.national.com
LM397
Typical Performance Characteristics
TA = 25˚C. Unless otherwise specified.
Supply Current vs. Supply Voltage
Input Bias Current vs. Supply Current
20022103
20022101
Output Saturation Voltage vs. Output Sink Current
Input Offset Voltage vs. Supply Voltage
20022104
20022102
Response Time for Various Input Overdrives – tPHL
Response Time for Various Input Overdrives – tPLH
20022105
www.national.com
20022106
4
For an inverting configured comparator, hysteresis can be
added with a three resistor network and positive feedback.
When input voltage (VIN) at the inverting node is less than
non-inverting node (VT), the output is high. The equivalent
circuit for the three resistor network is R1 in parallel with R3
and in series with R2. The lower threshold voltage VT1 is
calculated by:
VT1 = ((VS R2) / (((R1 R3) / (R1 + R3)) + R2))
Basic Comparators
A comparator is quite often used to convert an analog signal
to a digital signal. The comparator compares an input voltage (VIN) at the non-inverting pin to the reference voltage
(VREF) at the inverting pin. If VIN is less than VREF the output
(VO) is low (VOL). However, if VIN is greater than VREF, the
output voltage (VO) is high (VOH). Refer to Figure 2.
When VIN is greater than VT, the output voltage is low. The
equivalent circuit for the three resistor network is R2 in
parallel with R3 and in series with R1. The upper threshold
voltage VT2 is calculated by:
VT2 = VS ((R2 R3) / (R2 + R3)) / (R1 + ((R2 R3) / (R2 +
R3)))
The hysteresis is defined as
∆VIN = VT1 – VT2
20022110
20022112
20022111
FIGURE 2. Basic Comparator
Hysteresis
The basic comparator configuration may oscillate or produce
a noisy output if the applied differential input is near the
comparator’s input offset voltage. This tends to occur when
the voltage on the input is equal or very close to the other
input voltage. Adding hysteresis can prevent this problem.
Hysteresis creates two switching thresholds (one for the
rising input voltage and the other for the falling input voltage). Hysteresis is the voltage difference between the two
switching thresholds. When both inputs are nearly equal,
hysteresis causes one input to effectively move quickly pass
the other. Thus, effectively moving the input out of region that
oscillation may occur.
20022113
FIGURE 3. Inverting Configured Comparator – LM397
5
www.national.com
LM397
Application Notes
LM397
Application Notes
(Continued)
Input Stage
The LM397 has a bipolar input stage. The input common
mode voltage range is from 0 to (VS – 1.5V).
Output Stage
The LM397 has an open collector grounded-emitter NPN
output transistor for the output stage. This requires an external pull-up resistor connected between the positive supply
voltage and the output. The external pull-up resistor should
be high enough resistance so to avoid excessive power
dissipation. In addition, the pull-up resistor should be low
enough resistance to enable the comparator to switch with
the load circuitry connected. Because it is an open collector
output stage, several comparator outputs can be connected
together to create an OR’ing function output. With an open
collector, the output can be used as a simple SPST switch to
ground.The amount of current which the output can sink is
approximately 10mA. When the maximum current limit is
reached, the output transistor will saturate and the output will
rise rapidly (Figure 4).
www.national.com
20022107
FIGURE 4. Output Saturation Voltage vs. Output Sink
Current
6
LM397
SOT23-5 Tape and Reel Specification
Tape Format
Tape Section
# Cavities
Cavity Status
Cover Tape Status
Leader (Start End)
0 (min)
Empty
Sealed
75 (min)
Empty
Sealed
3000
Filled
Sealed
1000
Filled
Sealed
Carrier
Trailer (Hub End)
125 (min)
Empty
Sealed
0 (min)
Empty
Sealed
TAPE DIMENSIONS
20022115
8mm
0.130
(3.3)
0.124
(3.15)
0.130
(3.3)
0.126
(3.2)
0.138 ± 0.002
(3.5 ± 0.05)
0.055 ± 0.004
(1.4 ± 0.11)
0.157
(4)
0.315 ± 0.012
(8 ± 0.3)
Tape Size
DIM A
DIM Ao
DIM B
DIM Bo
DIM F
DIM Ko
DIM P1
DIM W
7
www.national.com
LM397
SOT23-5 Tape and Reel Specification
(Continued)
REEL DIMENSIONS
20022116
8mm
7.00
330.00
0.059
1.50
0.512
13.00
0.795
20.20
2.165
55.00
0.331 + 0.059/−0.000
8.40 + 1.50/−0.00
0.567
14.40
W1 + 0.078/−0.039
W1 + 2.00/−1.00
Tape Size
A
B
C
D
N
W1
W2
W3
www.national.com
8
LM397 Single General Purpose Voltage Comparator
Physical Dimensions
inches (millimeters) unless otherwise noted
5-Pin SOT23
NS Package Number MF05A
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
National Semiconductor
Corporation
Americas
Email: [email protected]
www.national.com
National Semiconductor
Europe
Fax: +49 (0) 180-530 85 86
Email: [email protected]
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
Email: [email protected]
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
Similar pages